Add a parameter to eeh_pe_state_clear() that allows passed-through PEs
to be excluded. Update callers to always pass true so that there is no
change in behaviour.
Also refactor to use direct traversal, to allow the removal of some
boilerplate.
This is to prepare for follow-up work for passed-through devices.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
eeh_unfreeze_pe() performs two operations: unfreezing a PE (which may
cause firmware to unfreeze child PEs as well) and de-isolating the PE
and it's children.
To simplify this and support future work, separate out the
de-isolation and perform it at the call sites (when necessary).
There should be no change in behaviour.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Including (in no particular order):
- Page table code for AMD IOMMU now supports large pages where
smaller page-sizes were mapped before. VFIO had to work around
that in the past and I included a patch to remove it (acked by
Alex Williamson)
- Patches to unmodularize a couple of IOMMU drivers that would
never work as modules anyway.
- Work to unify the the iommu-related pointers in
'struct device' into one pointer. This work is not finished
yet, but will probably be in the next cycle.
- NUMA aware allocation in iommu-dma code
- Support for r8a774a1 and r8a774c0 in the Renesas IOMMU driver
- Scalable mode support for the Intel VT-d driver
- PM runtime improvements for the ARM-SMMU driver
- Support for the QCOM-SMMUv2 IOMMU hardware from Qualcom
- Various smaller fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=DT9A
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- Page table code for AMD IOMMU now supports large pages where smaller
page-sizes were mapped before. VFIO had to work around that in the
past and I included a patch to remove it (acked by Alex Williamson)
- Patches to unmodularize a couple of IOMMU drivers that would never
work as modules anyway.
- Work to unify the the iommu-related pointers in 'struct device' into
one pointer. This work is not finished yet, but will probably be in
the next cycle.
- NUMA aware allocation in iommu-dma code
- Support for r8a774a1 and r8a774c0 in the Renesas IOMMU driver
- Scalable mode support for the Intel VT-d driver
- PM runtime improvements for the ARM-SMMU driver
- Support for the QCOM-SMMUv2 IOMMU hardware from Qualcom
- Various smaller fixes and improvements
* tag 'iommu-updates-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (78 commits)
iommu: Check for iommu_ops == NULL in iommu_probe_device()
ACPI/IORT: Don't call iommu_ops->add_device directly
iommu/of: Don't call iommu_ops->add_device directly
iommu: Consolitate ->add/remove_device() calls
iommu/sysfs: Rename iommu_release_device()
dmaengine: sh: rcar-dmac: Use device_iommu_mapped()
xhci: Use device_iommu_mapped()
powerpc/iommu: Use device_iommu_mapped()
ACPI/IORT: Use device_iommu_mapped()
iommu/of: Use device_iommu_mapped()
driver core: Introduce device_iommu_mapped() function
iommu/tegra: Use helper functions to access dev->iommu_fwspec
iommu/qcom: Use helper functions to access dev->iommu_fwspec
iommu/of: Use helper functions to access dev->iommu_fwspec
iommu/mediatek: Use helper functions to access dev->iommu_fwspec
iommu/ipmmu-vmsa: Use helper functions to access dev->iommu_fwspec
iommu/dma: Use helper functions to access dev->iommu_fwspec
iommu/arm-smmu: Use helper functions to access dev->iommu_fwspec
ACPI/IORT: Use helper functions to access dev->iommu_fwspec
iommu: Introduce wrappers around dev->iommu_fwspec
...
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files.
Semantic patch information:
Rationale: DEFINE_SIMPLE_ATTRIBUTE + debugfs_create_file()
imposes some significant overhead as compared to
DEFINE_DEBUGFS_ATTRIBUTE + debugfs_create_file_unsafe().
Generated by: scripts/coccinelle/api/debugfs/debugfs_simple_attr.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use the new function to replace the open-coded iommu check.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell Currey <ruscur@russell.cc>
Cc: Sam Bobroff <sbobroff@linux.ibm.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The wait_state member of eeh_ops does not need to be platform
dependent; it's just logic around eeh_ops.get_state(). Therefore,
merge the two (slightly different!) platform versions into a new
function, eeh_wait_state() and remove the eeh_ops member.
While doing this, also correct:
* The wait logic, so that it never waits longer than max_wait.
* The wait logic, so that it never waits less than
EEH_STATE_MIN_WAIT_TIME.
* One call site where the result is treated like a bit field before
it's checked for negative error values.
* In pseries_eeh_get_state(), rename the "state" parameter to "delay"
because that's what it is.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, eeh_pe_state_mark() marks a PE (and it's children) with a
state and then performs additional processing if that state included
EEH_PE_ISOLATED.
The state parameter is always a constant at the call site, so
rearrange eeh_pe_state_mark() into two functions and just call the
appropriate one at each site.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function eeh_pe_state_mark_with_cfg() just performs the work of
eeh_pe_state_mark() and then, conditionally, the work of
eeh_pe_state_clear(). However it is only ever called with a constant
state such that the condition is always true, so replace it by direct
calls.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently a flag, EEH_POSTPONED_PROBE, is used to prevent an incorrect
message "EEH: No capable adapters found" from being displayed during
the boot of powernv systems.
It is necessary because, on powernv, the call to eeh_probe_devices()
made from eeh_init() is too early and EEH can't yet be enabled. A
second call is made later from eeh_pnv_post_init(), which succeeds.
(On pseries, the first call succeeds because PCI devices are set up
early enough and no second call is made.)
This can be simplified by moving the early call to eeh_probe_devices()
from eeh_init() (where it's seen by both platforms) to
pSeries_final_fixup(), so that each platform only calls
eeh_probe_devices() once, at a point where it can succeed.
This is slightly later in the boot sequence, but but still early
enough and it is now in the same place in the sequence for both
platforms (the pcibios_fixup hook).
The display of the message can be cleaned up as well, by moving it
into eeh_probe_devices().
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If an error occurs during an unplug operation, it's possible for
eeh_dump_dev_log() to be called when edev->pdn is null, which
currently leads to dereferencing a null pointer.
Handle this by skipping the error log for those devices.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Due to recent refactoring in EEH in:
commit b9fde58db7 ("powerpc/powernv: Rework EEH initialization on
powernv")
a misleading message was seen in the kernel message buffer:
[ 0.108431] EEH: PowerNV platform initialized
[ 0.589979] EEH: No capable adapters found
This happened due to the removal of the initialization delay for powernv
platform.
Even though the EEH infrastructure for the devices is eventually
initialized and still works just fine the eeh device probe step is
postponed in order to assure the PEs are created. Later
pnv_eeh_post_init does the probe devices job but at that point the
message was already shown right after eeh_init flow.
This patch introduces a new flag EEH_POSTPONED_PROBE to represent that
temporary state and avoid the message mentioned above and showing the
follow one instead:
[ 0.107724] EEH: PowerNV platform initialized
[ 4.844825] EEH: PCI Enhanced I/O Error Handling Enabled
Signed-off-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Tested-by:Venkat Rao B <vrbagal1@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Notable changes:
- Support for split PMD page table lock on 64-bit Book3S (Power8/9).
- Add support for HAVE_RELIABLE_STACKTRACE, so we properly support live
patching again.
- Add support for patching barrier_nospec in copy_from_user() and syscall entry.
- A couple of fixes for our data breakpoints on Book3S.
- A series from Nick optimising TLB/mm handling with the Radix MMU.
- Numerous small cleanups to squash sparse/gcc warnings from Mathieu Malaterre.
- Several series optimising various parts of the 32-bit code from Christophe Leroy.
- Removal of support for two old machines, "SBC834xE" and "C2K" ("GEFanuc,C2K"),
which is why the diffstat has so many deletions.
And many other small improvements & fixes.
There's a few out-of-area changes. Some minor ftrace changes OK'ed by Steve, and
a fix to our powernv cpuidle driver. Then there's a series touching mm, x86 and
fs/proc/task_mmu.c, which cleans up some details around pkey support. It was
ack'ed/reviewed by Ingo & Dave and has been in next for several weeks.
Thanks to:
Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Al Viro, Andrew
Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Arnd Bergmann, Balbir Singh,
Cédric Le Goater, Christophe Leroy, Christophe Lombard, Colin Ian King, Dave
Hansen, Fabio Estevam, Finn Thain, Frederic Barrat, Gautham R. Shenoy, Haren
Myneni, Hari Bathini, Ingo Molnar, Jonathan Neuschäfer, Josh Poimboeuf,
Kamalesh Babulal, Madhavan Srinivasan, Mahesh Salgaonkar, Mark Greer, Mathieu
Malaterre, Matthew Wilcox, Michael Neuling, Michal Suchanek, Naveen N. Rao,
Nicholas Piggin, Nicolai Stange, Olof Johansson, Paul Gortmaker, Paul
Mackerras, Peter Rosin, Pridhiviraj Paidipeddi, Ram Pai, Rashmica Gupta, Ravi
Bangoria, Russell Currey, Sam Bobroff, Samuel Mendoza-Jonas, Segher
Boessenkool, Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stewart Smith,
Thiago Jung Bauermann, Torsten Duwe, Vaibhav Jain, Wei Yongjun, Wolfram Sang,
Yisheng Xie, YueHaibing.
-----BEGIN PGP SIGNATURE-----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=ZlBf
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- Support for split PMD page table lock on 64-bit Book3S (Power8/9).
- Add support for HAVE_RELIABLE_STACKTRACE, so we properly support
live patching again.
- Add support for patching barrier_nospec in copy_from_user() and
syscall entry.
- A couple of fixes for our data breakpoints on Book3S.
- A series from Nick optimising TLB/mm handling with the Radix MMU.
- Numerous small cleanups to squash sparse/gcc warnings from Mathieu
Malaterre.
- Several series optimising various parts of the 32-bit code from
Christophe Leroy.
- Removal of support for two old machines, "SBC834xE" and "C2K"
("GEFanuc,C2K"), which is why the diffstat has so many deletions.
And many other small improvements & fixes.
There's a few out-of-area changes. Some minor ftrace changes OK'ed by
Steve, and a fix to our powernv cpuidle driver. Then there's a series
touching mm, x86 and fs/proc/task_mmu.c, which cleans up some details
around pkey support. It was ack'ed/reviewed by Ingo & Dave and has
been in next for several weeks.
Thanks to: Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Al
Viro, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Arnd
Bergmann, Balbir Singh, Cédric Le Goater, Christophe Leroy, Christophe
Lombard, Colin Ian King, Dave Hansen, Fabio Estevam, Finn Thain,
Frederic Barrat, Gautham R. Shenoy, Haren Myneni, Hari Bathini, Ingo
Molnar, Jonathan Neuschäfer, Josh Poimboeuf, Kamalesh Babulal,
Madhavan Srinivasan, Mahesh Salgaonkar, Mark Greer, Mathieu Malaterre,
Matthew Wilcox, Michael Neuling, Michal Suchanek, Naveen N. Rao,
Nicholas Piggin, Nicolai Stange, Olof Johansson, Paul Gortmaker, Paul
Mackerras, Peter Rosin, Pridhiviraj Paidipeddi, Ram Pai, Rashmica
Gupta, Ravi Bangoria, Russell Currey, Sam Bobroff, Samuel
Mendoza-Jonas, Segher Boessenkool, Shilpasri G Bhat, Simon Guo,
Souptick Joarder, Stewart Smith, Thiago Jung Bauermann, Torsten Duwe,
Vaibhav Jain, Wei Yongjun, Wolfram Sang, Yisheng Xie, YueHaibing"
* tag 'powerpc-4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (251 commits)
powerpc/64s/radix: Fix missing ptesync in flush_cache_vmap
cpuidle: powernv: Fix promotion from snooze if next state disabled
powerpc: fix build failure by disabling attribute-alias warning in pci_32
ocxl: Fix missing unlock on error in afu_ioctl_enable_p9_wait()
powerpc-opal: fix spelling mistake "Uniterrupted" -> "Uninterrupted"
powerpc: fix spelling mistake: "Usupported" -> "Unsupported"
powerpc/pkeys: Detach execute_only key on !PROT_EXEC
powerpc/powernv: copy/paste - Mask SO bit in CR
powerpc: Remove core support for Marvell mv64x60 hostbridges
powerpc/boot: Remove core support for Marvell mv64x60 hostbridges
powerpc/boot: Remove support for Marvell mv64x60 i2c controller
powerpc/boot: Remove support for Marvell MPSC serial controller
powerpc/embedded6xx: Remove C2K board support
powerpc/lib: optimise PPC32 memcmp
powerpc/lib: optimise 32 bits __clear_user()
powerpc/time: inline arch_vtime_task_switch()
powerpc/Makefile: set -mcpu=860 flag for the 8xx
powerpc: Implement csum_ipv6_magic in assembly
powerpc/32: Optimise __csum_partial()
powerpc/lib: Adjust .balign inside string functions for PPC32
...
To aid debugging, add a message to show when EEH processing for a PE
will be done at the device's parent, rather than directly at the
device.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The traversal functions eeh_pe_traverse() and eeh_pe_dev_traverse()
both provide their first argument as void * but every single user casts
it to the expected type.
Change the type of the first parameter from void * to the appropriate
type, and clean up all uses.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Variants of proc_create{,_data} that directly take a seq_file show
callback and drastically reduces the boilerplate code in the callers.
All trivial callers converted over.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Checking for a "fully active" device state requires testing two flag
bits, which is open coded in several places, so add a function to do
it.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ttq9
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- skip AER driver error recovery callbacks for correctable errors
reported via ACPI APEI, as we already do for errors reported via the
native path (Tyler Baicar)
- fix DPC shared interrupt handling (Alex Williamson)
- print full DPC interrupt number (Keith Busch)
- enable DPC only if AER is available (Keith Busch)
- simplify DPC code (Bjorn Helgaas)
- calculate ASPM L1 substate parameter instead of hardcoding it (Bjorn
Helgaas)
- enable Latency Tolerance Reporting for ASPM L1 substates (Bjorn
Helgaas)
- move ASPM internal interfaces out of public header (Bjorn Helgaas)
- allow hot-removal of VGA devices (Mika Westerberg)
- speed up unplug and shutdown by assuming Thunderbolt controllers
don't support Command Completed events (Lukas Wunner)
- add AtomicOps support for GPU and Infiniband drivers (Felix Kuehling,
Jay Cornwall)
- expose "ari_enabled" in sysfs to help NIC naming (Stuart Hayes)
- clean up PCI DMA interface usage (Christoph Hellwig)
- remove PCI pool API (replaced with DMA pool) (Romain Perier)
- deprecate pci_get_bus_and_slot(), which assumed PCI domain 0 (Sinan
Kaya)
- move DT PCI code from drivers/of/ to drivers/pci/ (Rob Herring)
- add PCI-specific wrappers for dev_info(), etc (Frederick Lawler)
- remove warnings on sysfs mmap failure (Bjorn Helgaas)
- quiet ROM validation messages (Alex Deucher)
- remove redundant memory alloc failure messages (Markus Elfring)
- fill in types for compile-time VGA and other I/O port resources
(Bjorn Helgaas)
- make "pci=pcie_scan_all" work for Root Ports as well as Downstream
Ports to help AmigaOne X1000 (Bjorn Helgaas)
- add SPDX tags to all PCI files (Bjorn Helgaas)
- quirk Marvell 9128 DMA aliases (Alex Williamson)
- quirk broken INTx disable on Ceton InfiniTV4 (Bjorn Helgaas)
- fix CONFIG_PCI=n build by adding dummy pci_irqd_intx_xlate() (Niklas
Cassel)
- use DMA API to get MSI address for DesignWare IP (Niklas Cassel)
- fix endpoint-mode DMA mask configuration (Kishon Vijay Abraham I)
- fix ARTPEC-6 incorrect IS_ERR() usage (Wei Yongjun)
- add support for ARTPEC-7 SoC (Niklas Cassel)
- add endpoint-mode support for ARTPEC (Niklas Cassel)
- add Cadence PCIe host and endpoint controller driver (Cyrille
Pitchen)
- handle multiple INTx status bits being set in dra7xx (Vignesh R)
- translate dra7xx hwirq range to fix INTD handling (Vignesh R)
- remove deprecated Exynos PHY initialization code (Jaehoon Chung)
- fix MSI erratum workaround for HiSilicon Hip06/Hip07 (Dongdong Liu)
- fix NULL pointer dereference in iProc BCMA driver (Ray Jui)
- fix Keystone interrupt-controller-node lookup (Johan Hovold)
- constify qcom driver structures (Julia Lawall)
- rework Tegra config space mapping to increase space available for
endpoints (Vidya Sagar)
- simplify Tegra driver by using bus->sysdata (Manikanta Maddireddy)
- remove PCI_REASSIGN_ALL_BUS usage on Tegra (Manikanta Maddireddy)
- add support for Global Fabric Manager Server (GFMS) event to
Microsemi Switchtec switch driver (Logan Gunthorpe)
- add IDs for Switchtec PSX 24xG3 and PSX 48xG3 (Kelvin Cao)
* tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe endpoint controller
PCI: endpoint: Fix EPF device name to support multi-function devices
PCI: endpoint: Add the function number as argument to EPC ops
PCI: cadence: Add host driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe host controller
PCI: Add vendor ID for Cadence
PCI: Add generic function to probe PCI host controllers
PCI: generic: fix missing call of pci_free_resource_list()
PCI: OF: Add generic function to parse and allocate PCI resources
PCI: Regroup all PCI related entries into drivers/pci/Makefile
PCI/DPC: Reformat DPC register definitions
PCI/DPC: Add and use DPC Status register field definitions
PCI/DPC: Squash dpc_rp_pio_get_info() into dpc_process_rp_pio_error()
PCI/DPC: Remove unnecessary RP PIO register structs
PCI/DPC: Push dpc->rp_pio_status assignment into dpc_rp_pio_get_info()
PCI/DPC: Squash dpc_rp_pio_print_error() into dpc_rp_pio_get_info()
PCI/DPC: Make RP PIO log size check more generic
PCI/DPC: Rename local "status" to "dpc_status"
PCI/DPC: Squash dpc_rp_pio_print_tlp_header() into dpc_rp_pio_print_error()
...
Add EEH platform operations for pseries to update VF config space.
With this change after EEH, the VF will have updated config space for
pseries platform.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Juan J. Alvarez <jjalvare@linux.vnet.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove the post_init callback which is only used
by powernv, we can just call it explicitly from
the powernv code.
This partially kills the ability to "disable" eeh at
runtime via debugfs as this was calling that same
callback again, but this is both unused and broken
in several ways. If we want to revive it, we need
to create a dedicated enable/disable callback on the
backend that does the right thing.
Let the bulk of eeh initialize normally at
core_initcall() like it does on pseries by removing
the hack in eeh_init() that delays it.
Instead we make sure our eeh->probe cleanly bails
out of the PEs haven't been created yet and we force
a re-probe where we used to call eeh_init() again.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Otherwise we end up not yet having computed the right diag data size
on powernv where EEH initialization is delayed, thus causing memory
corruption later on when calling OPAL.
Fixes: 5cb1f8fddd ("powerpc/powernv/pci: Dynamically allocate PHB diag data")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The pci_dn struct caches a OF device node pointer in order to access
the "ibm,loc-code" property when EEH is recovering.
However, when this happens in eeh_dev_check_failure(), we also have
a pci_dev pointer which should have a valid pointer to the device node
when pci_dn has one (both pointers are not NULL for physical functions
and are NULL for virtual functions).
This changes pci_remove_device_node_info() to look for a parent of
the node being removed, just like pci_add_device_node_info() does when it
references the parent node.
This is the first step to get rid of pci_dn::node.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The eeh_dev struct already holds a pointer to pci_dn which it does not
exist without and pci_dn itself holds the very same pointer so just
use it.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add newer helpers to make the function usage simpler. It is always
recommended to use find_current_mm_pte() for walking the page table.
If we cannot use find_current_mm_pte(), it should be documented why
the said usage of __find_linux_pte() is safe against a parallel THP
split.
For now we have KVM code using __find_linux_pte(). This is because kvm
code ends up calling __find_linux_pte() in real mode with MSR_EE=0 but
with PACA soft_enabled = 1. We may want to fix that later and make
sure we keep the MSR_EE and PACA soft_enabled in sync. When we do that
we can switch kvm to use find_linux_pte().
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc_debugfs_root is the dentry representing the root of the
"powerpc" directory tree in debugfs.
Currently it sits in asm/debug.h, a long with some other things that
have "debug" in the name, but are otherwise unrelated.
Pull it out into a separate header, which also includes linux/debugfs.h,
and convert all the users to include debugfs.h instead of debug.h.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We give up recovery on permanent error, simply shutdown the affected
devices and remove them. If the devices can't be put into quiet state,
they spew more traffic that is likely to cause another unexpected EEH
error. This was observed on "p8dtu2u" machine:
0002:00:00.0 PCI bridge: IBM Device 03dc
0002:01:00.0 Ethernet controller: Intel Corporation \
Ethernet Controller X710/X557-AT 10GBASE-T (rev 02)
0002:01:00.1 Ethernet controller: Intel Corporation \
Ethernet Controller X710/X557-AT 10GBASE-T (rev 02)
0002:01:00.2 Ethernet controller: Intel Corporation \
Ethernet Controller X710/X557-AT 10GBASE-T (rev 02)
0002:01:00.3 Ethernet controller: Intel Corporation \
Ethernet Controller X710/X557-AT 10GBASE-T (rev 02)
On P8 PowerNV platform, the IO path is frozen when shutdowning the
devices, meaning the memory registers are inaccessible. It is why
the devices can't be put into quiet state before removing them.
This fixes the issue by enabling IO path prior to putting the devices
into quiet state.
Reported-by: Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
eeh_pe_reset and eeh_reset_pe are two different functions in the same
file which do mostly the same thing. Not only is this confusing, but
potentially causes disrepancies in functionality, notably eeh_reset_pe
as it does not check return values for failure.
Refactor this into the following:
- eeh_pe_reset(): stays as is, performs a single operation, exported
- eeh_pe_reset_full(): new, full reset process that calls eeh_pe_reset()
- eeh_reset_pe(): removed and replaced by eeh_pe_reset_full()
- eeh_reset_pe_once(): removed
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PHB, PE (and by association MVE) numbers are printed as a mix of decimal
and hexadecimal throughout the kernel. This can be misleading, so make
them all hexadecimal.
Standardising on hex instead of dec because:
- PHB numbers are presented in hex in sysfs/debugfs (and lspci, etc)
- PE numbers are presented as hex in sysfs and parsed in hex in debugfs
The only place I think this could cause confusing are the messages during
boot, i.e.
pci 000a:01 : [PE# 000] Secondary bus 1 associated with PE#0
which can be a quick way to check PE numbers. pe_level_printk() will
only print two characters instead of three, so the above would be
pci 000a:01 : [PE# 00] Secondary bus 1 associated with PE#0
which gives a hint it's in hex.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
No real need for this to be pr_warn(), reduce it to pr_info().
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This exports @confirm_error_lock so that eeh_serialize_{lock, unlock}()
can be used to freeze the affected PE in PCI surprise hot remove path.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Function eeh_pe_set_option() is used to apply the requested options
(enable, disable, unfreeze) in EEH virtualization path. The semantics
of this function isn't complete until freezing is supported.
This allows to freeze the indicated PE. The new semantics is going to
be used in PCI surprise hot remove path, to freeze removed PCI devices
(PE) to avoid unexpected EEH error reporting.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is a very minor/trivial fix for the output of PCI address on EEH
logs. The PCI address on "OF node" field currently is using ":" as a
separator for the function, but the usual separator is ".". This patch
changes the separator to dot, so the PCI address is printed as usual.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reverts commit 89a51df5ab.
The function eeh_add_device_early() is used to perform EEH
initialization in devices added later on the system, like in
hotplug/DLPAR scenarios. Since the commit 89a51df5ab ("powerpc/eeh:
Fix crash in eeh_add_device_early() on Cell") a new check was introduced
in this function - Cell has no EEH capabilities which led to kernel oops
if hotplug was performed, so checking for eeh_enabled() was introduced
to avoid the issue.
However, in architectures that EEH is present like pSeries or PowerNV,
we might reach a case in which no PCI devices are present on boot time
and so EEH is not initialized. Then, if a device is added via DLPAR for
example, eeh_add_device_early() fails because eeh_enabled() is false,
and EEH end up not being enabled at all.
This reverts the aforementioned patch since a new verification was
introduced by the commit d91dafc02f ("powerpc/eeh: Delay probing EEH
device during hotplug") and so the original Cell issue does not happen
anymore.
Cc: stable@vger.kernel.org # v4.1+
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The label "reset" in eeh_pe_change_owner() is used only for once.
No need to keep it and just drop it. No logical changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
IBM online documentation for EEH uses "extended error handling" and
"enhanced error handling" to refer to the same thing, in different
places. The only place mentioning it as "enhanced error handling" in the
kernel is the MAINTAINERS file, and it's "extended" in some documentation.
IBM originally defined EEH as "enhanced error handling", so standardise
all mentions of EEH to use that term.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In eeh_pci_enable(), after making the request to set the new options, we
call eeh_ops->wait_state() to check that the request finished successfully.
At the moment, if eeh_ops->wait_state() returns 0, we return 0 without
checking that it reflects the expected outcome. This can lead to callers
further up the chain incorrectly assuming the slot has been successfully
unfrozen and continuing to attempt recovery.
On powernv, this will occur if pnv_eeh_get_pe_state() or
pnv_eeh_get_phb_state() return 0, which in turn occurs if the relevant OPAL
call returns OPAL_EEH_STOPPED_MMIO_DMA_FREEZE or
OPAL_EEH_PHB_ERROR respectively.
On pseries, this will occur if pseries_eeh_get_state() returns 0, which in
turn occurs if RTAS reports that the PE is in the MMIO Stopped and DMA
Stopped states.
Obviously, none of these cases represent a successful completion of a
request to thaw MMIO or DMA.
Fix the check so that a wait_state() return value of 0 won't be considered
successful for the EEH_OPT_THAW_MMIO or EEH_OPT_THAW_DMA cases.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When eeh_dump_pe_log() is only called by eeh_slot_error_detail(),
we already have the check that the PE isn't in PCI config blocked
state in eeh_slot_error_detail(). So we needn't the duplicated
check in eeh_dump_pe_log().
This removes the duplicated check in eeh_dump_pe_log(). No logical
changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When passing through SRIOV VFs to guest, we possibly encounter EEH
error on PF. In this case, the VF PEs are put into frozen state.
The error could be reported to guest before it's captured by the
host. That means the guest could attempt to recover errors on VFs
before host gets chance to recover errors on PFs. The VFs won't be
recovered successfully.
This enforces the recovery order for above case: the recovery on
child PE in guest is hold until the recovery on parent PE in host
is completed.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PFs are enumerated on PCI bus, while VFs are created by PF's driver.
In EEH recovery, it has two cases:
1. Device and driver is EEH aware, error handlers are called.
2. Device and driver is not EEH aware, un-plug the device and plug it again
by enumerating it.
The special thing happens on the second case. For a PF, we could use the
original pci core to enumerate the bus, while for VF we need to record the
VFs which aer un-plugged then plug it again.
Also The patch caches the VF index in pci_dn, which can be used to
calculate VF's bus, device and function number. Those information helps to
locate the VF's PCI device instance when doing hotplug during EEH recovery
if necessary.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PEs for VFs don't have primary bus. So they have to have their own reset
backend, which is used during EEH recovery. The patch implements the reset
backend for VF's PE by issuing FLR or AF FLR to the VFs, which are contained
in the PE.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The comment block above pcibios_set_pcie_reset_state() incorrectly refers
to pcibios_set_pcie_slot_reset(). Fix the comment accordingly.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When one or both of the below two flags are marked in the PE state, the
PE's IO path is regarded as enabled: EEH_STATE_MMIO_ACTIVE or
EEH_STATE_MMIO_ENABLED.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
No need to have two atomic opertions (update and fetch/check) when
decreasing PE's number of passed devices as one atomic operation
is enough.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We need to properly identify whether a hugepage is an explicit or
a transparent hugepage in follow_huge_addr(). We used to depend
on hugepage shift argument to do that. But in some case that can
result in wrong results. For ex:
On finding a transparent hugepage we set hugepage shift to PMD_SHIFT.
But we can end up clearing the thp pte, via pmdp_huge_get_and_clear.
We do prevent reusing the pfn page via the usage of
kick_all_cpus_sync(). But that happens after we updated the pte to 0.
Hence in follow_huge_addr() we can find hugepage shift set, but transparent
huge page check fail for a thp pte.
NOTE: We fixed a variant of this race against thp split in commit
691e95fd73
("powerpc/mm/thp: Make page table walk safe against thp split/collapse")
Without this patch, we may hit the BUG_ON(flags & FOLL_GET) in
follow_page_mask occasionally.
In the long term, we may want to switch ppc64 64k page size config to
enable CONFIG_ARCH_WANT_GENERAL_HUGETLB
Reported-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The config space of some PCI devices can't be accessed when their
PEs are in frozen state. Otherwise, fenced PHB might be seen.
Those PEs are identified with flag EEH_PE_CFG_RESTRICTED, meaing
EEH_PE_CFG_BLOCKED is set automatically when the PE is put to
frozen state (EEH_PE_ISOLATED). eeh_slot_error_detail() restores
PCI device BARs with eeh_pe_restore_bars(), which then calls
eeh_ops->restore_config() to reinitialize the PCI device in
(OPAL) firmware. eeh_ops->restore_config() produces PCI config
access that causes fenced PHB. The problem was reported on below
adapter:
0001:01:00.0 0200: 14e4:168e (rev 10)
0001:01:00.0 Ethernet controller: Broadcom Corporation \
NetXtreme II BCM57810 10 Gigabit Ethernet (rev 10)
This fixes the issue by skipping eeh_pe_restore_bars() in
eeh_slot_error_detail() when EEH_PE_CFG_BLOCKED is set for the PE.
Fixes: b6541db1 ("powerpc/eeh: Block PCI config access upon frozen PE")
Cc: stable@vger.kernel.org # v4.0+
Reported-by: Manvanthara B. Puttashankar <mputtash@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
pcibios_set_pcie_reset_state() could be called to complete
reset request when passing through PCI device, flag
EEH_PE_ISOLATED is set before saving the PCI config sapce.
On some Broadcom adapters, EEH_PE_CFG_BLOCKED is automatically
set when the flag EEH_PE_ISOLATED is marked. It caused bogus
data saved from the PCI config space, which will be restored
to the PCI adapter after the reset. Eventually, the hardware
can't work with corrupted data in PCI config space.
The patch fixes the issue with eeh_pe_state_mark_no_cfg(), which
doesn't set EEH_PE_CFG_BLOCKED when seeing EEH_PE_ISOLATED on the
PE, in order to avoid the bogus data saved and restored to the PCI
config space.
Reported-by: Rajanikanth H. Adaveeshaiah <rajanikanth.ha@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In the complete hotplug case, EEH PEs are supposed to be released
and set to NULL. Normally, this is done by eeh_remove_device(),
which is called from pcibios_release_device().
However, if something is holding a kref to the device, it will not
be released, and the PE will remain. eeh_add_device_late() has
a check for this which will explictly destroy the PE in this case.
This check in eeh_add_device_late() occurs after a call to
eeh_ops->probe(). On PowerNV, probe is a pointer to pnv_eeh_probe(),
which will exit without probing if there is an existing PE.
This means that on PowerNV, devices with outstanding krefs will not
be rediscovered by EEH correctly after a complete hotplug. This is
affecting CXL (CAPI) devices in the field.
Put the probe after the kref check so that the PE is destroyed
and affected devices are correctly rediscovered by EEH.
Fixes: d91dafc02f ("powerpc/eeh: Delay probing EEH device during hotplug")
Cc: stable@vger.kernel.org
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This relies on the fact that a PCI device always has an IOMMU table
which may not be the case when we get dynamic DMA windows so
let's use more reliable check for IOMMU group here.
As we do not rely on the table presence here, remove the workaround
from pnv_pci_ioda2_set_bypass(); also remove the @add_to_iommu_group
parameter from pnv_ioda_setup_bus_dma().
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 28158cd "powerpc/eeh: Enhance pcibios_set_pcie_reset_state()"
introduced a fix for a problem where certain configurations could lead to
pci_reset_function() destroying the state of PCI devices other than the one
specified.
Unfortunately, the fix has a trivial bug - it calls pci_save_state() again,
when it should be calling pci_restore_state(). This corrects the problem.
Cc: Gavin Shan <gwshan@au1.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, the macro IS_BRIDGE is not used any where.
This patch just removes it.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch defines PCI error types and functions in uapi/asm/eeh.h
and exports function eeh_pe_inject_err(), which will be called by
VFIO driver to inject the specified PCI error to the indicated
PE for testing purpose.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 1c509148b ("powerpc/eeh: Do probe on pci_dn") probes EEH
devices in early stage, which is reasonable to pSeries platform.
However, it's wrong for PowerNV platform because the PE# isn't
determined until the resources (IO and MMIO) are assigned to
PE in hotplug case. So we have to delay probing EEH devices
for PowerNV platform until the PE# is assigned.
Fixes: ff57b454dd ("powerpc/eeh: Do probe on pci_dn")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When asserting reset in pcibios_set_pcie_reset_state(), the PE
is enforced to (hardware) frozen state in order to drop unexpected
PCI transactions (except PCI config read/write) automatically by
hardware during reset, which would cause recursive EEH error.
However, the (software) frozen state EEH_PE_ISOLATED is missed.
When users get 0xFF from PCI config or MMIO read, EEH_PE_ISOLATED
is set in PE state retrival backend. Unfortunately, nobody (the
reset handler or the EEH recovery functinality in host) will clear
EEH_PE_ISOLATED when the PE has been passed through to guest.
The patch sets and clears EEH_PE_ISOLATED properly during reset
in function pcibios_set_pcie_reset_state() to fix the issue.
Fixes: 28158cd ("Enhance pcibios_set_pcie_reset_state()")
Reported-by: Carol L. Soto <clsoto@us.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Carol L. Soto <clsoto@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We can disable a THP split or a hugepage collapse by disabling irq.
We do send IPI to all the cpus in the early part of split/collapse,
and disabling local irq ensure we don't make progress with
split/collapse. If the THP is getting split we return NULL from
find_linux_pte_or_hugepte(). For all the current callers it should be ok.
We need to be careful if we want to use returned pte_t pointer outside
the irq disabled region. W.r.t to THP split, the pfn remains the same,
but then a hugepage collapse will result in a pfn change. There are
few steps we can take to avoid a hugepage collapse.One way is to take page
reference inside the irq disable region. Other option is to take
mmap_sem so that a parallel collapse will not happen. We can also
disable collapse by taking pmd_lock. Another method used by kvm
subsystem is to check whether we had a mmu_notifer update in between
using mmu_notifier_retry().
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The recent change to the EEH probing causes a crash on Cell because
eeh_ops is NULL.
Check if EEH is enabled and if not bail out.
Fixes: ff57b454dd ("powerpc/eeh: Do probe on pci_dn")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch removes struct eeh_dev::dn and the corresponding helper
functions: eeh_dev_to_of_node() and of_node_to_eeh_dev(). Instead,
eeh_dev_to_pdn() and pdn_to_eeh_dev() should be used to get the
pdn, which might contain device_node on PowerNV platform.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are 3 EEH operations whose arguments contain device_node:
read_config(), write_config() and restore_config(). The patch
replaces device_node with pci_dn.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Originally, EEH core probes on device_node or pci_dev to populate
EEH devices and PEs, which conflicts with the fact: SRIOV VFs are
usually enabled and created by PF's driver and they don't have the
corresponding device_nodes. Instead, SRIOV VFs have dynamically
created pci_dn, which can be used for EEH probe.
The patch reworks EEH probe for PowerNV and pSeries platforms to
do probing based on pci_dn, instead of pci_dev or device_node any
more.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Function pcibios_set_pcie_reset_state() is possibly called by
pci_reset_function(), on which VFIO infrastructure depends to
issue reset. pcibios_set_pcie_reset_state() is issuing reset
on the parent PE of the indicated PCI device. The reset causes
state lost on all PCI devices except the indicated one as the
argument to pcibios_set_pcie_reset_state(). Also, sideband
MMIO access from guest when issuing reset would cause unexpected
EEH error.
For above two issues, the patch applies following enhancements
to pcibios_set_pcie_reset_state():
* For all PCI devices except the indicated one, save their
state prior to reset and restore state after that.
* Explicitly freeze PE prior to reset and unfreeze it after
that, in order to avoid unexpected EEH error.
Tested-by: Priya M. A <priyama2@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When PE's frozen count hits maximal allowed frozen times, which is
5 currently, it will be forced to be offline permanently. Once the
PE is removed permanently, rebooting machine is required to bring
the PE back. It's not convienent when testing EEH functionality.
The patch exports the maximal allowed frozen times through debugfs
entry (/sys/kernel/debug/powerpc/eeh_max_freezes).
Requested-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is what we get in dmesg when booting a pseries guest and
the hypervisor doesn't provide EEH support.
[ 0.166655] EEH functionality not supported
[ 0.166778] eeh_init: Failed to call platform init function (-22)
Since both powernv_eeh_init() and pseries_eeh_init() already complain when
hitting an error, it is not needed to print more (especially such an
uninformative message).
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On PowerNV platform, PHB diag-data is dumped after stopping device
drivers. In case of recursive EEH errors, the kernel is usually
crashed before dumping PHB diag-data for the second EEH error. It's
hard to locate the root cause of the second EEH error without PHB
diag-data.
The patch adds one more EEH option "eeh=early_log", which helps
dumping PHB diag-data immediately once frozen PE is detected, in
order to get the PHB diag-data for the second EEH error.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In PCI passthrou scenario, we need simulate EEH recovery for Emulex
adapters when their ownership changes, as we did in commit 5cfb20b96
("powerpc/eeh: Emulate EEH recovery for VFIO devices"). Broadcom
BCM5719 adpaters are facing same problem and needs same cure.
Reported-by: Rajeshkumar Subramanian <rajeshkumars@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch introduces additional flag EEH_PE_RESET to indicate the
corresponding PE is under reset. In turn, the PE retrieval bakcend
on PowerNV platform can return unfrozen state for the EEH core to
moving forward. Flag EEH_PE_CFG_BLOCKED isn't the correct one for
the purpose.
In PCI passthrou case, the problem is more worse: Guest doesn't
recover 6th EEH error. The PE is left in isolated (frozen) and
config blocked state on Broadcom adapters. We can't retrieve the
PE's state correctly any more, even from the host side via sysfs
/sys/bus/pci/devices/xxx/eeh_pe_state.
Reported-by: Rajeshkumar Subramanian <rajeshkumars@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch refactors eeh_reset_pe() in order for:
* Varied return values for different failure cases.
* Replace pr_err() with pr_warn() and print function name.
* Coding style cleanup.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When the PE's config space is marked as blocked, PCI config read
requests always return 0xFF's. It's pointless to collect logs in
this case.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The flag EEH_PE_RESET indicates blocking config space of the PE
during reset time. We potentially need block PE's config space
other than reset time. So it's reasonable to replace it with
EEH_PE_CFG_BLOCKED to indicate its usage.
There are no substantial code or logic changes in this patch.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The PEs can be organized as nested. Current implementation doesn't
dump PCI config space for subordinate devices of child PEs. However,
the frozen PE could be caused by those subordinate devices of its
child PEs.
The patch dumps PCI config space for all subordinate devices of the
problematic PE.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When enabling EEH functionality on passed through devices (PE)
with VFIO, the devices in the PE would be removed permanently
from guest side. In that case, the PE remains frozen state.
When returning PE to host, or restarting the guest again, we
had mechanism unfreezing the PE by clearing PESTA/B frozen
bits. However, that's not enough for some adapters, which are
indicated as following "lspci" shows. Those adapters require
hot reset on the parent bus to bring their firmware back to
workable state. Otherwise, those adaptrs won't be operative
and the host (for returning case) or the guest will fail to
load the drivers for those adapters without exception.
0000:01:00.0 Ethernet controller: Emulex Corporation OneConnect \
10Gb NIC (be3) (rev 02)
0000:01:00.0 0200: 19a2:0710 (rev 02)
0001:03:00.0 Ethernet controller: Emulex Corporation OneConnect \
NIC (Lancer) (rev 10)
0001:03:00.0 0200: 10df:e220 (rev 10)
The patch adds mechanism to emulate EEH recovery (for hot reset
on parent PCI bus) on 3 gates to fix the issue: open/release one
adapter of the PE, enable EEH functionality on one adapter of the
PE.
Reported-by: Murilo Fossa Vicentini <muvic@br.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PE would be owned by userland, which probably request PE reset
done in host side. During the reset, we should drop the PCI
config accesses to the PE with help of flag EEH_PE_RESET.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Function pcibios_set_pcie_reset_state() can be used to do PCI
reset. PCI config access during the reset usually causes EEH
errors unexpectedly. In order to avoid the EEH error, the patch
blocks PCI config access during reset with the help of flag
EEH_PE_RESET, which is similar to what we did in EEH PE reset
path.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch uses eeh_unfreeze_pe() to replace the logic clearing
frozen IO and DMA, in order to simplify the code.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When passing through PE to guest, that's possibly in frozen
state. The driver for the pass-through devices on guest side
can't be loaded successfully as reported. We already had one
gate in eeh_dev_open() to clear PE frozen state accordingly,
but that's not enough because the function is only called at
QEMU startup for once.
The patch adds another gate in eeh_pe_set_option() so that the
PE frozen state can be cleared at QEMU restart time.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function eeh_pci_enable() is called to apply various requests
to one particular PE: Enabling EEH, Disabling EEH, Enabling IO,
Enabling DMA, Freezing PE. When enabling IO or DMA on one specific
PE, we need check that IO or DMA isn't enabled previously. But
the condition used to do the check isn't completely correct because
one PE would be in DMA frozen state with workable IO path, or vice
versa.
The patch fixes the improper condition.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When passing through device, its PE might have been put into frozen
state. One obvious example would be: the passed PE is forced to be
offline because of hitting maximal allowed EEH errors in userland.
In that case, the frozen state won't be cleared and then the PE is
returned back to host, which might not have chance detecting and
recovering from it.
The patch adds more check when passing through device and clear the
PE frozen state if necessary.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The PCI devices that have been passed through are enabled before
reset, we need restore to the enabled state after reset. Otherwise,
MMIO access might be issued to disabled devices after reset and
causes exceptional recursive EEH error.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch adds one more option (EEH_OPT_FREEZE_PE) to set_option()
method to proactively freeze PE, which will be issued before resetting
pass-throughed PE to drop MMIO access during reset because it's
always contributing to recursive EEH error.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
eeh_check_failure() is used to check frozen state of the PE which
owns the indicated I/O address. The argument "val" of the function
isn't used. The patch drops it and return the frozen state of the
PE as expected.
Cc: Vishal Mansur <vmansur@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function is used by VFIO driver, which might be built as a
dynamic module. So it should be exported.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some new functions are exposed for use by the IOMMU code but
won't build when CONFIG_IOMMU_API isn't set, so shield them
appropriately.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_warn() is equal to pr_warning(), but the former is a bit more
formal according to commit fc62f2f ("kernel.h: add pr_warn for
symmetry to dev_warn, netdev_warn").
The patch replaces pr_warning() with pr_warn().
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch prints 4 PCIE or AER config registers each line, which
is part of the EEH log so that it looks a bit more compact.
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
According to the experiment I did, PCI config access is blocked
on P7IOC frozen PE by hardware, but PHB3 doesn't do that. That
means we always get 0xFF's while dumping PCI config space of the
frozen PE on P7IOC. We don't have the problem on PHB3. So we have
to enable I/O prioir to collecting error log. Otherwise, meaningless
0xFF's are always returned.
The patch fixes it by EEH flag (EEH_ENABLE_IO_FOR_LOG), which is
selectively set to indicate the case for: P7IOC on PowerNV platform,
pSeries platform.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are multiple global EEH flags. Almost each flag has its own
accessor, which doesn't make sense. The patch refactors EEH flag
accessors so that they look unified:
eeh_add_flag(): Add EEH flag
eeh_clear_flag(): Clear EEH flag
eeh_has_flag(): Check if one specific flag has been set
eeh_enabled(): Check if EEH functionality has been enabled
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Function eeh_iommu_group_to_pe() iterates each PCI device to check
the binding IOMMU group with get_iommu_table_base(), which possibly
fetches pdev->dev.archdata.dma_data.dma_offset. It's (0x1 << 59)
for "bypass" cases.
The patch fixes the issue by iterating devices hooked to the IOMMU
group and fetch IOMMU table there.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch exports functions to be used by new VFIO ioctl command,
which will be introduced in subsequent patch, to support EEH
functinality for VFIO PCI devices.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We must not handle EEH error on devices which are passed to somebody
else. Instead, we expect that the frozen device owner detects an EEH
error and recovers from it.
This avoids EEH error handling on passed through devices so the device
owner gets a chance to handle them.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As Ben suggested, it's meaningful to dump PE's location code
for site engineers when hitting EEH errors. The patch introduces
function eeh_pe_loc_get() to retireve the location code from
dev-tree so that we can output it when hitting EEH errors.
If primary PE bus is root bus, the PHB's dev-node would be tried
prior to root port's dev-node. Otherwise, the upstream bridge's
dev-node of the primary PE bus will be check for the location code
directly.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we have the corner case of frozen parent and child PE at the
same time, we have to handle the frozen parent PE prior to the
child. Without clearning the frozen state on parent PE, the child
PE can't be recovered successfully.
The patch searches the EEH PE hierarchy tree and returns the toppest
frozen PE to be handled. It ensures the frozen parent PE will be
handled prior to child PE.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 7f52a526f ("powerpc/eeh: Allow to disable EEH") caused
following build error with "celleb_defconfig" as being catched
by Mikey on linux-next.
arch/powerpc/kernel/eeh.c: In function 'eeh_init_proc':
arch/powerpc/kernel/eeh.c:1173:37: error: 'powerpc_debugfs_root' \
undeclared (first use in this function)
arch/powerpc/kernel/eeh.c:1173:37: note: each undeclared identifier \
is reported only once for each function it appears in
Reported-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Basically, we have 3 types of resets to fulfil PE reset: fundamental,
hot and PHB reset. For the later 2 cases, we need PCI bus reset hold
and settlement delay as specified by PCI spec. PowerNV and pSeries
platforms are running on top of different firmware and some of the
delays have been covered by underly firmware (PowerNV).
The patch makes the delays unified to be done in backend, instead of
EEH core.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch introduces bootarg "eeh=off" to disable EEH functinality.
Also, it creates /sys/kerenl/debug/powerpc/eeh_enable to disable
or enable EEH functionality. By default, we have the functionality
enabled.
For PowerNV platform, we will restore to have the conventional
mechanism of clearing frozen PE during PCI config access if we're
going to disable EEH functionality. Conversely, we will rely on
EEH for error recovery.
The patch also fixes the issue that we missed to cover the case
of disabled EEH functionality in function ioda_eeh_event(). Those
events driven by interrupt should be cleared to avoid endless
reporting.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There're 2 EEH subsystem variables: eeh_subsystem_enabled and
eeh_probe_mode. We needn't maintain 2 variables and we can just
have one variable and introduce different flags. The patch also
introduces additional flag EEH_FORCE_DISABLE, which will be used
to disable EEH subsystem via boot parameter ("eeh=off") in future.
Besides, the patch also introduces flag EEH_ENABLED, which is
changed to disable or enable EEH functionality on the fly through
debugfs entry in future.
With the patch applied, the creteria to check the enabled EEH
functionality is changed to:
!EEH_FORCE_DISABLED && EEH_ENABLED : Enabled
Other cases : Disabled
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When calling into eeh_gather_pci_data() on pSeries platform, we
possiblly don't have pci_dev instance yet, but eeh_dev is always
ready. So we use cached capability from eeh_dev instead of pci_dev
for log dump there. In order to keep things unified, we also cache
PCI capability positions to eeh_dev for PowerNV as well.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch replaces printk(KERN_WARNING ...) with pr_warn() in the
function eeh_gather_pci_data().
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have suffered recrusive frozen PE a lot, which was caused
by IO accesses during the PE reset. Ben came up with the good
idea to keep frozen PE until recovery (BAR restore) gets done.
With that, IO accesses during PE reset are dropped by hardware
and wouldn't incur the recrusive frozen PE any more.
The patch implements the idea. We don't clear the frozen state
until PE reset is done completely. During the period, the EEH
core expects unfrozen state from backend to keep going. So we
have to reuse EEH_PE_RESET flag, which has been set during PE
reset, to return normal state from backend. The side effect is
we have to clear frozen state for towice (PE reset and clear it
explicitly), but that's harmless.
We have some limitations on pHyp. pHyp doesn't allow to enable
IO or DMA for unfrozen PE. So we don't enable them on unfrozen PE
in eeh_pci_enable(). We have to enable IO before grabbing logs on
pHyp. Otherwise, 0xFF's is always returned from PCI config space.
Also, we had wrong return value from eeh_pci_enable() for
EEH_OPT_THAW_DMA case. The patch fixes it too.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When doing PE reset, EEH_PE_ISOLATED is cleared unconditionally.
However, We should remove that if the PE reset has cleared the
frozen state successfully. Otherwise, the flag should be kept.
The patch fixes the issue.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PE state (for eeh_pe instance) EEH_PE_PHB_DEAD is duplicate to
EEH_PE_ISOLATED. Originally, those PHBs (PHB PE) with EEH_PE_PHB_DEAD
would be removed from the system. However, it's safe to replace
that with EEH_PE_ISOLATED.
The patch also clear EEH_PE_RECOVERING after fenced PHB has been handled,
either failure or success. It makes the PHB PE state consistent with:
PHB functions normally NONE
PHB has been removed EEH_PE_ISOLATED
PHB fenced, recovery in progress EEH_PE_ISOLATED | RECOVERING
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We possiblly detect EEH errors during reboot, particularly in kexec
path, but it's impossible for device drivers and EEH core to handle
or recover them properly.
The patch registers one reboot notifier for EEH and disable EEH
subsystem during reboot. That means the EEH errors is going to be
cleared by hardware reset or second kernel during early stage of
PCI probe.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch cleans up variable eeh_subsystem_enabled so that we needn't
refer the variable directly from external. Instead, we will use
function eeh_enabled() and eeh_set_enable() to operate the variable.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>