The WM8325 is a PMIC for low power, high performance applications. From
a software point of view the device is identical to the WM8320, all the
differences are at the hardware level.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fixes below sparse warning.
drivers/mfd/twl-core.c:258:20: warning: symbol 'twl_map' was not declared. Should it be static?
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Tony Lindgren <tony@atomide.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch defines platform data for the ks8842 int the timberdale
MFD.
The platform data contains DMA channels to be used by the driver.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add PM helpers to STMPE and add support to enable wakeup from low power
states
Acked-by: Rabin VINCENT <rabin.vincent@stericsson.com>
Acked-by: Linus WALLEIJ <linus.walleij@stericsson.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Free allocated memory. Call stmpe_disable() if it was enabled.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch add a dependancy for ab8500-core driver so as to depend on
u8500 platform.
This patch also fixes the build issues(powerpc_allyesconfig) for the
patch 03f582a93ecca6e9584b622570022abf08ed03ec (misc: Add ab8500 pwm
driver)
Signed-off-by: Arun Murthy <arun.murthy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for enabling and disabling tps6586x subdevice interrupts
Signed-off-by: Gary King <gking@nvidia.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds the choice of accessing the AB8500 registers
via prcmu I2C. Access either via SPI or I2C is supported.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds the possibility to read and write registers
via the debug_fs. It also adds ranges of registers sorted by bank
which makes it possible to read all defined registers in a bank.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds a Pulse Width Modulation driver for Analog Baseband
Chip AB8500.
Signed-off-by: Arun Murthy <arun.murthy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch makes the ab8500 mixed signal chip expose the same
interface for register access as the ab3100, ab3550 and ab5500 chip.
The ab8500_read() and ab8500_write() is removed and replaced with
abx500_get_register_interruptible() and
abx500_set_register_interruptible().
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch removes the requirement that gpio base be supplied in
platform data.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Adjust the tmio_mmc block size check to accept 2-byte requests in 4-bit
mode if the hardware supports it.
Tested with the SDHI hardware block included in sh7724.
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Magnus Damm <damm@opensource.se>
Tested-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In some platforms (e.g. AP4EVB) the card detect pin of a slot is not
directly connected to the sh_mmcif controller, so that polling needs
to be used. To overcome the overhead induced by querying the controller
on each poll cycle, card detection can be handled in the platform code
more efficiently.
This patch exposes a get_cd hook for that purpose.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On some platforms (e.g. AP4EVB) the card detect pin of a slot is not
directly connected to the sdhi hardware, so that polling needs to be used
with tmio_mmc and card detection is handled in the platform code.
This patch allows to set tmio_mmc capabilities (to pass the
MMC_CAP_NEEDS_POLL flag) and exposes a get_cd hook for that purpose.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some controllers, supported by the tmio_mmc driver do not have the card
detect pin of a slot connected, so that polling needs to be used and
card detection is handled by other means.
This patch exposes a get_cd hook for that purpose.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds support for the RTC provided by the Maxim 8998 chip. This
driver was tested on a GONI board by using the rtc-test application from
the Documentation/rtc.txt.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use genirq and provide seperated file for interrupts support.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The MAX8998 chip have regulator and rtc features. The i2c slave address
of regulator and rtc is different, so needs each i2c client on i2c
operation functions.
Also, this patch exports i2c operation functions instead of callback to
make easy to read.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
1. return -ENOMEM if platform_device_alloc() fail.
2. call platform_device_put() if platform_device_add() fail.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
1. return -ENOMEM if platform_device_alloc() fail.
2. call platform_device_put() if platform_device_add() fail.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch fixes da903x_add_subdevs error path:
1. return -ENOMEM if platform_device_alloc() fail.
2. call platform_device_put() if platform_device_add() fail.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add codec IRQ resources that are used in 88pm860x codec driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
For the resources allocated in tps6586x_i2c_probe(),
we need to free it in tps6586x_i2c_remove().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
use the new definitions on twl header for code
consistency.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
use the new definitions on twl header for code
consistency.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
use the new definitions on twl header for code
consistency.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
LP3974 PMIC support. It has same functionality as max8998.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
GPIOs on these controller are multi-functional. If you decided to use
some of them e.g. as input channels for the ADC, you surely don't want
those pins to be reassigned as simple GPIOs (which may be triggered even
from userspace via 'export'). Same for the touchscreen controller pins.
Since knowledge about the hardware is needed to decide which GPIOs to
reserve, let this bitmask be inside platform_data and provide some
defines to assist potential users.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This switches the AB3100 core driver to using MFD cells for
subdevices instead of spawning common platform devices.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since there is no discardable probe() function in the I2C device
framework, let's just tag it __devinit and take the footprint hit
rather than seeing the compilation warnings every day.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fixed warnings about unprototyped global functions.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds support for the Broadcom BCM63xx SoC built-in watchdog, it
uses one of the BCM63xx hardware timer id.
Signed-off-by: Miguel Gaio <miguel.gaio@efixo.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On iEi PCISA-9652-R10 (BIOS version 1.5) single board computer reads
from the game port do not seem to reset the watchdog timer. This patch
adds a module parameter wdt_config_reg to specify alternative reset
sources. At least WDT_RESET_KBD has been tested, even just running
while true; do
setleds -L +scroll
sleep 1
setleds -L -scroll
sleep 1
done
is enough to keep the watchdog happy.
Signed-off-by: Timo Juhani Lindfors <timo.lindfors@iki.fi>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds support for watchdogs with 8b timers, like ones in
IT8702F and older revisions of IT8712F Super IO chip, to it87_wdt
driver. This patch should be used after the patch
'it87_wdt: Add support for IT8720F watchdog'.
Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
In current implementation, vid is declared as u8,
then "vid == -1" is always false, and "vid >= 0" is always true.
Thus change it to s8.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Commit f03f91826 (regulator: Add option for machine drivers
to enable the dummy regulator) in the regulators tree
seems to have introduced the following build break when
CONFIG_REGULATOR_DUMMY is disabled. Fix this.
CC drivers/regulator/dummy.o
drivers/regulator/dummy.c:41: error: redefinition of 'regulator_dummy_init'
drivers/regulator/dummy.h:28: note: previous definition of 'regulator_dummy_init' was here
make[2]: *** [drivers/regulator/dummy.o] Error 1
make[1]: *** [drivers/regulator] Error 2
make: *** [drivers] Error 2
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
I have a regulator A that sets regulator B as its supply. When I call
set_supply to add B as the supply for A, regulator A gets added to the
supply_list for regulator B.
When I call regulator_disable(A), I end up with a call chain like this:
regulator_disable(A)
> mutex_lock(A)
> _regulator_disable(A)
>> _regulator_disable(B)
>>> _notifier_call_chain(B)
>>>> mutex_lock(A)
Which results in dead lock since we are trying to acquire the mutex lock
for regulator A which we already hold.
This patch addresses this issue by moving the call to disable regulator
B outside of the lock aquired inside the initial call to
regulator_disable.
This change also addresses the issue of not acquiring the mutex for
regulator B before calling _regulator_disable(B).
Signed-off-by: Jeffrey Carlyle <jeff.carlyle@motorola.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow machine drivers to explicitly enable the use of the dummy regulator,
enabling simpler support for systems with only a few specific supplies
visible to software.
It is strongly recommended that this is not used on systems with
substantial software control over their PMICs, for maximum functionality
constrints should be as fully specified as possible.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch includes below fixes based on Mark's comment.
- Return actual error if i2c_smbus_read_byte_data() fail
- Add spaces around bitwise AND operator(&) to improve readability
- Add comment to explain why we need to update voltage change control register
for LDO1 and LDO5
- Logging the value for diagnostics if chip reported incorrect voltage value
- Add __devinit annotation for setup_regulators()
- Show system control register1 value if the value is mismatched
- Logging the value for diagnostics if failed to detect device
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds regulator drivers for National Semiconductors LP3972 PMIC.
This LP3972 PMIC controller has 3 DC/DC voltage converters and 5 low drop-out
(LDO) regulators. LP3972 PMIC controller uses I2C interface.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
MAX8952 PMIC is used to provide voltage output between 770mV - 1400mV
with DVS support. In this initial release, users can set voltages for
four DVS modes, RAMP delay values, and SYNC frequency.
Controlling FPWM/SYNC_MODE/Pull-Down/Ramp Modes and reading CHIP_ID
is not supported in this release.
If GPIO of EN is not valid in platform data, the driver assumes that it
is always-on. If GPIO of VID0 or VID1 is invalid, the driver pulls down
VID0 and VID1 to fix DVS mode as 0 and disables DVS support.
We assume that V_OUT is capable to provide every voltage from 770mV to
1.40V in 10mV steps although the data sheet has some ambiguity on it.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
--
v2:
- Style correction
- Can accept platform_data with invalid GPIOs
- Removed unnecessary features
- Improved error handling
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This simple patch adds support for a watchdog in IT8720F Super IO chip
to it87_wdt driver.
Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The current iTCO_wdt driver warnings are confusing. Currently when the device
driver returns an error the console contains:
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: failed to reset NO_REBOOT flag, reboot disabled by hardware
iTCO_wdt: No card detected
After the patch,
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: failed to reset NO_REBOOT flag, device disabled by hardware/BIOS
Clean this up and use the word "device" to describe the device.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds the Intel Patsburg (PCH) DeviceIDs for iTCO Watchdog.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: (68 commits)
hwmon: (it87) Add support for the IT8721F/IT8758E
hwmon: (it87) Move conversion functions
hwmon: Remove many EXPERIMENTAL flags
hwmon: (lm85) Add support for ADT7468 high-frequency PWM mode
hwmon: (lm85) Document the ADT7468 as supported
hwmon: (lm85) Fix ADT7468 frequency table
hwmon: I2C addresses are constant
Move ams driver to macintosh
hwmon: (pcf8591) Don't attempt to detect devices
hwmon: (pcf8591) Register as a hwmon device
hwmon: (w83795) Use standard attributes for chassis intrusion
hwmon: (w83795) Exclude fan control feature by default
hwmon: (w83795) Add myself as co-author and maintainer
hwmon: (w83795) More style cleanups
hwmon: (w83795) Fix LSB reading of voltage limits
hwmon: (w83795) Use dev_get_drvdata() where possible
hwmon: (w83795) Delay reading pwm config registers
hwmon: (w83795) Delay reading limit registers
hwmon: (w83795) Move register reads to dedicated functions
hwmon: (w83795) Pack similar register reads
...
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits)
x86: allocate space within a region top-down
x86: update iomem_resource end based on CPU physical address capabilities
x86/PCI: allocate space from the end of a region, not the beginning
PCI: allocate bus resources from the top down
resources: support allocating space within a region from the top down
resources: handle overflow when aligning start of available area
resources: ensure callback doesn't allocate outside available space
resources: factor out resource_clip() to simplify find_resource()
resources: add a default alignf to simplify find_resource()
x86/PCI: MMCONFIG: fix region end calculation
PCI: Add support for polling PME state on suspended legacy PCI devices
PCI: Export some PCI PM functionality
PCI: fix message typo
PCI: log vendor/device ID always
PCI: update Intel chipset names and defines
PCI: use new ccflags variable in Makefile
PCI: add PCI_MSIX_TABLE/PBA defines
PCI: add PCI vendor id for STmicroelectronics
x86/PCI: irq and pci_ids patch for Intel Patsburg DeviceIDs
PCI: OLPC: Only enable PCI configuration type override on XO-1
...
This patch enables and disables the rx and tx bits in the MAC control reg
by using a single write operation.
This also solves a possible problem (spotted on SPEAr platforms) at 10Mbps
where two consecutive writes to a MAC control register can take more than
4 phy_clk cycles.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/atarilance.c: In function ‘addr_accessible’:
drivers/net/atarilance.c:413: warning: comparison of distinct pointer types lacks a cast
drivers/net/atarilance.c:450: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset the whole hw instead of freeing hw resources
consumed by each pci function.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Crash is triggered by commit e6484930d7 ("net: allocate tx queues in
register_netdevice"), which moved tx netqueue creation into register_netdev.
So now calling netif_stop_queue() before register_netdev causes an oops.
Move netif_stop_queue() after net device registration to fix crash.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the IT8721F/IT8758E. These new chips differ from the
older IT87xxF chips in the following ways:
* ADC LSB is 12 mV instead of 16 mV.
* PWM values are 8-bit instead of 7-bit.
There are other minor changes we don't have to care about in the
driver.
Another change is that we will handle internal voltage scaling in the
driver instead of delegating the work to user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move conversion functions until after structure defintions. This is
needed for future changes which make use of the structures in the
conversion funtcions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove the dependency on EXPERIMENTAL for all drivers which are in
the kernel tree for a long time, are known to work properly and for
which we have documentation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Corentin Labbe <corentin.labbe@geomatys.fr>
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: Juerg Haefliger <juergh@gmail.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The ADT7468 supports a high-frequency PWM output mode where all PWM
outputs are driven by a 22.5 kHz clock. Add support for this mode, and
document it, as it may surprise the user that setting one PWM output
frequency also affects the other PWM outputs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The ADT7468 uses the same frequency table as the ADT7463.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Cc: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
We can mark normal_i2c const. Almost all drivers do that already, so
fix the 3 remaining ones before they are used as (bad) examples for
new drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: George Joseph <george.joseph@fairview5.com>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
The ams driver isn't a hardware monitoring driver, so it shouldn't
live under driver/hwmon. drivers/macintosh seems much more
appropriate, as the driver is only useful on PowerBooks and iBooks.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Stelian Pop <stelian@popies.net>
Cc: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
The PCF8591 can't be detected, don't even try. There are plenty of
other means to instantiate i2c devices these days.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Register PCF8591 devices as hwmon devices. There's little point in
implementing the standard sysfs interface if we don't register it in
a way libsensors will pick it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Follow the standard attribute naming for the chassis intrusion
feature. I couldn't test the beeping (my board apparently doesn't do
that) but the alarm works fine.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The fan control feature of the w83795 driver is insufficiently
reviewed and tested for public consumption at this time, so make it
optional and disabled by default. We will change the default when
review and testing is deemed sufficient. Ultimately the option will
go away.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
I've made so many changes to the w83795 driver that it's only fair to
list myself as a co-author. I'll also maintain the driver for some
time. There's more work needed on the driver for sure.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cleanups suggested by Guenter Roeck, falling into 4 categories:
* Swapping test orders, because if (var == CONSTANT) is much easier to
read than if (CONSTANT == var).
* Simplifying comparisons with 0.
* Dropping unneeded masks.
* Dropping unneeded parentheses and curly braces.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
When we don't need the client pointer, calling dev_get_drvdata() is
more efficient that calling to_i2c_client() and then
i2c_get_clientdata().
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Wait until we need the pwm config register values, instead of
pre-reading them. This saves over 1 second on modprobe on my test
system.
Obviously this time is added when first accessing pwm config
attributes, however not everybody will use them, so it seems unfair
to slow down driver loading (and thus boot) for an optional feature.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Wait until we need the limit register values, instead of pre-reading
them. This saves 544 ms on modprobe on my test system. Obviously this
time is added when first running "sensors" or any other monitoring
application, but I think it is better than slowing down the boot.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move initial register reads out of probe, to dedicated functions.
This makes the code clearer, and will be needed if we want to delay
calling these functions until they are needed, or want to call them
periodically.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cascaded conditionals are inefficient. Reorder the fields so that
PWM register addresses can be computed more efficiently.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
There is no point in reading registers during initialization if we
will refresh the values in the update function later. This is only
slowing down the driver loading with no benefit, stop doing it.
This change saves 480 ms on driver load on my test system.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
All 3 temperature sensor type sysfs functions (show_temp_mode,
store_temp_mode and show_dts_mode) can be simplified. We don't
create these files when the correponding input isn't in temperature
monitoring mode, so there is no point in handling that case.
Likewise, we don't allow changing inputs from temperature to voltage,
so the code handling this case is dead and can be removed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
VRLSB_SHIFT is a non-sense, the actual shift depends on the sensor
type (fans need 4, other sensors need 6). Get rid of it to prevent
any confusion. Also get rid of the useless masking, the meaningful
bits are always the MSb so there's nothing to mask out after
shifting.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Shorten driver load time by avoiding duplicate register access during
initialization. This saves 112 ms on modprobe on my test system.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Handle beep_enable just like all other beep bits. It doesn't need
anything special, so let's avoid redundant code. This also saves a
duplicate register read at initialization time.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The PWM duty cycle frequenty attributes are improperly named
(fanN_div instead of pwmN_div) and contain raw values instead of
actual frequencies. Rename them and fix their contents.
Also improve the logic when the user asks for a new frequency, to
always pick the closest supported frequency. The algorithm could
certainly be optimized, but the operation is infrequent enough that
I don't think it's worth the effort.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The W83795G can be configured to set the in0, in1 and/or in2 voltage
limits dynamically based on VID input pins. Switch the respective
sysfs attributes to read-only.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Misplaced parentheses caused the wrong register value to be read,
resulting in random LSB for fan speed values and limits.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* The data structure is zalloc'd, so no need to set individual fields
to 0 explicitly.
* Refactor the handling of pins that can be used for either
temperature or voltage monitoring.
* Misc other clean-ups.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Only create fan[1-8]_target files when the fan in question can be
controlled (PWM output is present.) Also name these files according
to the standard.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use a dedicated 2D array for PWM attributes. This way, PWM attributes
are handled the same way as other attributes, this is more consistent.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use 2D arrays for in, fan, temp and dts device attributes. Using
linear arrays is too risky as we have to skip some groups depending
on the device model and configuration. Adding or removing an
attribute would let the driver build silently but then it would crash
at runtime. With 2D arrays, the consistency checking happens at build
time, which is much safer.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Functions w83795_create_files and w83795_remove_files iterate over
the same set of files, just calling a different function. Merge them
into a single function which takes the action as a parameter. This
saves code, and also ensure that file creation and deletion are in
sync.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Function w83795_probe() is way too big, move file creation to a separate
function to make it more readable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Sysfs files must be removed on device removal but also when device
registration fails. Move the code to a separate function to avoid
code redundancy.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move the bank selection code to a separate function, to avoid
duplicating it in read and write functions. Improve error reporting
on register access error.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Enum chips and chip_types are redundant, get rid of the former. Fix
the detection code to properly identify the chip variant and name the
client accordingly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There is still much work needed, but I wanted to give Wei the credit
he deserves. I've merged some of my own fixes already, to make
gcc and checkpatch happy. Individual fixes and improvements from me
will follow.
[JD: Fix build errors]
[JD: Coding style cleanups]
[JD: Get rid of forward declarations]
[JD: Drop VID support]
[JD: Drop fault output control feature]
[JD: Use lowercase for inline function names]
[JD: Use strict variants of the strtol/ul functions]
[JD: Shorten the read and write function names]
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This way we don't need to modify Kconfig every time a new SoC comes along to
make this driver support it. Also fix some typos while I'm at it.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The semaphore which protects the ADC is semantically a mutex. Use a
real mutex.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Currently we get the checkpatch warning
consider using strict_strtol in preference to simple_strtol.
Also we should not allow any partially numeric values.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
I was wondering if that chip ever existed publicly... Apparently yes,
so add support for it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Instead of using switch/case and if statements in probe, define chip specific
functionality in a parameter structure array.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The family check in k8temp is not required because the driver is
already bound to a northbridge device only used with K8 CPUs.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Along the same lines as "cxgb4: fix crash due to manipulating queues
before registration" (8f6d9f4047), before
commit "net: allocate tx queues in register_netdevice"
netif_tx_stop_all_queues and related functions could be used between
device allocation and registration but now only after registration.
cxgb4 has such a call before registration and crashes now. Move it
after register_netdev.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: eric.dumazet@gmail.com
Cc: sonnyrao@us.ibm.com
Cc: Divy Le Ray <divy@chelsio.com>
Cc: Dimitris Michailidis <dm@chelsio.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __NS8390_init tries to start the device queue before the
device is registered. This results in an oops (snipped):
[ 2.865493] BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
[ 2.866106] IP: [<ffffffffa000602a>] netif_start_queue+0xb/0x12 [8390]
[ 2.881267] Call Trace:
[ 2.881437] [<ffffffffa000624d>] __NS8390_init+0x102/0x15a [8390]
[ 2.881999] [<ffffffffa00062ae>] NS8390_init+0x9/0xb [8390]
[ 2.882237] [<ffffffffa000d820>] ne2k_pci_init_one+0x297/0x354 [ne2k_pci]
[ 2.882955] [<ffffffff811c7a0e>] local_pci_probe+0x12/0x16
[ 2.883308] [<ffffffff811c85ad>] pci_device_probe+0xc3/0xef
[ 2.884049] [<ffffffff8129218d>] driver_probe_device+0xbe/0x14b
[ 2.884937] [<ffffffff81292260>] __driver_attach+0x46/0x62
[ 2.885170] [<ffffffff81291788>] bus_for_each_dev+0x49/0x78
[ 2.885781] [<ffffffff81291fbb>] driver_attach+0x1c/0x1e
[ 2.886089] [<ffffffff812912ab>] bus_add_driver+0xba/0x227
[ 2.886330] [<ffffffff8129259a>] driver_register+0x9e/0x115
[ 2.886933] [<ffffffff811c8815>] __pci_register_driver+0x50/0xac
[ 2.887785] [<ffffffffa001102c>] ne2k_pci_init+0x2c/0x2e [ne2k_pci]
[ 2.888093] [<ffffffff81000212>] do_one_initcall+0x7c/0x130
[ 2.888693] [<ffffffff8106d74f>] sys_init_module+0x99/0x1da
[ 2.888946] [<ffffffff81002a2b>] system_call_fastpath+0x16/0x1b
This happens because the netif_start_queue sets respective bit on the dev->_tx
array which is not yet allocated.
As far as I understand the code removing the netif_start_queue from __NS8390_init
is OK, since queue will be started later on device open. Plz, correct me if I'm wrong.
Found in the Dave's current tree, so he's in Cc.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduced by commit:e6484930d7c73d324bccda7d43d131088da697b9
net: allocate tx queues in register_netdevice
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Acked-by: Greg Rose <greg.v.rose@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ixgb fails to work after reload on recent kernels:
rmmod ixgb (dev->current_state = PCI_UNKNOWN)
modprobe ixgb (pci_enable_device will bail leaving current_state to PCI_UNKNOWN)
ifup eth0
do_IRQ: 2.82 No irq handler for vector (irq -1)
The issue was exposed by commit fcd097f31a
PCI: MSI: Remove unsafe and unnecessary hardware access
which avoids HW writes for power states != PCI_D0
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DCB credits refill quantum _must_ be greater than half the max
packet size. This is needed to guarantee that TX DMA operations
are not attempted during a pause state. Additionally, the min IFG
must be set correctly for DCB mode. If a DMA operation is
requested unexpectedly during the pause state the HW data
store may be corrupted leading to a DMA hang. The DMA hang
requires a reset to correct. This fixes the HW configuration
to avoid this condition.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some parts need to execute resets during normal operation. This flag
check ensures that those parts reset without needlessly alarming the
user. Other unexpected resets by other parts will dump debug info
and message the reset action to the user, as originally intended.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some errors can be induced in the PHY via environmental testing
(specifically extreme temperature changes and electro static
discharge testing), and in the case of the PHY hanging due to
this input, this detects the problem and resets to continue.
This issue only applies to 82574 silicon.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the roundup macro is sane, it can't be used in structure
definitions, or the build breaks.. For now, create a "broken_roundup()"
macro to get everything building again, but in the end, fixing these
structures to use a proper size value is the correct thing to do.
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Henry Ptasinski <henryp@broadcom.com>
Cc: Nohee Ko <noheek@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The way network devices are reference counted does not include poking
around in the reference count itself. This breaks when the reference
count is changed to be a different type. Fix the driver to do the
proper function calls instead.
Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb tree renamed the USB storage defines to make more sense, so this
driver needs the changes as well so that things will compile properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This merges the staging-next tree to Linus's tree and resolves
some conflicts that were present due to changes in other trees that were
affected by files here.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (505 commits)
[media] af9015: Fix max I2C message size when used with tda18271
[media] IR: initialize ir_raw_event in few more drivers
[media] Guard a divide in v4l1 compat layer
[media] imon: fix nomouse modprobe option
[media] imon: remove redundant change_protocol call
[media] imon: fix my egregious brown paper bag w/rdev/idev split
[media] cafe_ccic: Configure ov7670 correctly
[media] ov7670: allow configuration of image size, clock speed, and I/O method
[media] af9015: support for DigitalNow TinyTwin v3 [1f4d:9016]
[media] af9015: map DigitalNow TinyTwin v2 remote
[media] DigitalNow TinyTwin remote controller
[media] af9015: RC fixes and improvements
videodev2.h.xml: Update to reflect the latest changes at videodev2.h
[media] v4l: document new Bayer and monochrome pixel formats
[media] DocBook/v4l: Add missing formats used on gspca cpia1 and sn9c2028
[media] firedtv: add parameter to fake ca_system_ids in CA_INFO
[media] tm6000: fix a macro coding style issue
tm6000: Remove some ugly debug code
[media] Nova-S-Plus audio line input
[media] [RFC,1/1] V4L2: Use new CAP bits in existing RDS capable drivers
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (66 commits)
mmc: add new sdhci-pxa driver for Marvell SoCs
mmc: make number of mmcblk minors configurable
mmc_spi: Recover from CRC errors for r/w operation over SPI.
mmc: sdhci-pltfm: add -pltfm driver for imx35/51
mmc: sdhci-of-esdhc: factor out common stuff
mmc: sdhci_pltfm: pass more data on custom init call
mmc: sdhci: introduce get_ro private write-protect hook
mmc: sdhci-pltfm: move .h file into appropriate subdir
mmc: sdhci-pltfm: Add structure for host-specific data
mmc: fix cb710 kconfig dependency warning
mmc: cb710: remove debugging printk (info duplicated from mmc-core)
mmc: cb710: clear irq handler on init() error path
mmc: cb710: remove unnecessary msleep()
mmc: cb710: implement get_cd() callback
mmc: cb710: partially demystify clock selection
mmc: add a file to debugfs for changing host clock at runtime
mmc: sdhci: allow for eMMC 74 clock generation by controller
mmc: sdhci: highspeed: check for mmc as well as sd cards
mmc: sdhci: Add Moorestown device support
mmc: sdhci: Intel Medfield support
...
This patch removes the controller overlap between cciss and hpsa. It was
decided that no overlap should exist. All new controllers will use the hpsa
SCSI based driver.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Structure IOCTL_Command_struct is copied to userland with
some padding fields at the end of the struct unitialized.
It leads to leaking of contents of kernel stack memory.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
As described in https://bugzilla.kernel.org/show_bug.cgi?id=19922
: I had an AoE device go down overnight, and while a server was trying to
: write to it, it was also writing this message to its logs:
:
: 209 printk(KERN_INFO "aoe: device %ld.%d is not up\n",
: 210 d->aoemajor, d->aoeminor);
:
: The message appeared many times per second, and over several hours
: produced about 7.5 gigabytes of log files, filling up all free space on
: the root filesystem.
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Suggested-by: Roman Mamedov <roman@rm.pp.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
If CONFIG_LBDAF=y, `sector_t' becomes `u64' instead of `unsigned long':
drivers/block/z2ram.c: In function ¡do_z2_request¢:
drivers/block/z2ram.c:83: warning: format %lu expects type `long unsigned int', but argument 2 has type `sector_t'
Hence always cast it to `unsigned long long' for printing. Also do the
pr_err() dance, while we're at it.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
flush_scheduled_work() is deprecated and scheduled to be removed.
Directly cancel aoedev->work on free instead of depending on
flush_scheduled_works().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Failure to create drbd_ee_mempool appears not to get checked. Looks like
a copy-and-paste problem to me.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Very recently, the RS485 interface has been fixed by adding two further
fields (see commit 1b6331848b).
Check the value of the flag SER_RS485_RTS_BEFORE_SEND before delaying.
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
(Updated to address Ben's comments. With regard to the message segment
restriction it's not something we hit on the actual platform so while
I will investigate that further I don't think its a blocker to submission.
At worst its a spot over-restrictive)
From: Wen Wang <wen.w.wang@intel.com>
Initial release of the driver. Updated and verified on hardware.
Cleaned up as follows
Alan Cox:
Squash down the switches into tables, and use the PCI ident field. We
could perhaps take this further and put the platform and port number into
this.
uint32t -> u32
bracketing of case statements
spacing and '!' usage
Check the speed (which is now 0/1/2) is valid and ignore otherwise.
Fix remaining problems/suggestions from Jean's review
Fix items from Ben's review
Arjan van de Ven:
Initial power management hooks
Yong Wang <youg.y.wang@intel.com>:
Shared IRQ support
Wen Wang <wen.w.wang@intel.com>:
D3 support
Fixes for OCT test runs
Interrupt optimisations
Hong Liu <hong.liu@intel.com>
The runtime PM code is working on the wrong device (i2c_adapter->dev).
The correct one should be pci_dev->dev. This breaks attached i2c
slave devices with runtime PM enabled. Slave device needs to runtime
resume parent device before runtime resuming itself, but we always get
error since we don't have pm_runtime callback for i2c_adapter->dev.
Bin Yang <bin.yang@intel.com>:
Update speed table
Saadi Maalem <saadi.maalem@intel.com>:
Clear all interrupts in the hardware init
Celine Chotard <celinex.chotard@intel.com>:
Correct ordering of clear/disable of IRQs
Signed-off-by: Wen Wang <wen.w.wang@intel.com>
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Bin Yang <bin.yang@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The driver is not buildable without MFD changes. For now, let's
disable the driver as it breaks build for major platforms (i.e. x86).
CC [M] drivers/power/twl4030_charger.o
drivers/power/twl4030_charger.c: In function 'twl4030_clear_set_boot_bci':
drivers/power/twl4030_charger.c:105: error: 'TWL4030_PM_MASTER_BOOT_BCI' undeclared (first use in this function)
drivers/power/twl4030_charger.c:105: error: (Each undeclared identifier is reported only once
drivers/power/twl4030_charger.c:105: error: for each function it appears in.)
drivers/power/twl4030_charger.c: In function 'twl4030_bci_have_vbus':
drivers/power/twl4030_charger.c:137: error: 'TWL4030_PM_MASTER_STS_HW_CONDITIONS' undeclared (first use in this function)
drivers/power/twl4030_charger.c: In function 'twl4030_bci_probe':
drivers/power/twl4030_charger.c:477: warning: overflow in implicit constant conversion
drivers/power/twl4030_charger.c:485: warning: overflow in implicit constant conversion
make[2]: *** [drivers/power/twl4030_charger.o] Error 1
We can re-enable it if MFD tree will finally merge into 2.6.37.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
bio_clone and bio_alloc allocate from a common bio pool.
If an md device is stacked with other devices that use this pool, or under
something like swap which uses the pool, then the multiple calls on
the pool can cause deadlocks.
So allocate a local bio pool for each md array and use that rather
than the common pool.
This pool is used both for regular IO and metadata updates.
Signed-off-by: NeilBrown <neilb@suse.de>
Currently sync_page_io takes a 'bdev'.
Every caller passes 'rdev->bdev'.
We will soon want another field out of the rdev in sync_page_io,
So just pass the rdev instead of the bdev out of it.
Signed-off-by: NeilBrown <neilb@suse.de>
Though this mem alloc is GFP_NOIO an so will not deadlock, it seems
better to do the allocation before 'raise_barrier' which stops any IO
requests while the resync proceeds.
raid10 always uses this order, so it is at least consistent to do the
same in raid1.
Signed-off-by: NeilBrown <neilb@suse.de>
bio_alloc can never fail (as it uses a mempool) but an block
indefinitely, especially if the caller is holding a reference to a
previously allocated bio.
So these to places which both handle failure and hold multiple bios
should not use bio_alloc, they should use bio_kmalloc.
Signed-off-by: NeilBrown <neilb@suse.de>
It is not safe to allocate from a mempool while holding an item
previously allocated from that mempool as that can deadlock when the
mempool is close to exhaustion.
So don't use a bio list to collect the bios to write to multiple
devices in raid1 and raid10.
Instead queue each bio as it becomes available so an unplug will
activate all previously allocated bios and so a new bio has a chance
of being allocated.
This means we must set the 'remaining' count to '1' before submitting
any requests, then when all are submitted, decrement 'remaining' and
possible handle the write completion at that point.
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Workqueue usage in md has two problems.
* Flush can be used during or depended upon by memory reclaim, but md
uses the system workqueue for flush_work which may lead to deadlock.
* md depends on flush_scheduled_work() to achieve exclusion against
completion of removal of previous instances. flush_scheduled_work()
may incur unexpected amount of delay and is scheduled to be removed.
This patch adds two workqueues to md - md_wq and md_misc_wq. The
former is guaranteed to make forward progress under memory pressure
and serves flush_work. The latter serves as the flush domain for
other works.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: NeilBrown <neilb@suse.de>
bitmap_get_counter returns the number of sectors covered
by the counter in a pass-by-reference variable.
In some cases this can be very large, so make it a sector_t
for safety.
Signed-off-by: NeilBrown <neilb@suse.de>
lock_kernel calls were recently pushed down into open/release
functions.
md doesn't need that protection.
Then the BKL calls were change to md_mutex. We don't need those
either.
So remove it all.
Signed-off-by: NeilBrown <neilb@suse.de>
A RAID1 which has no persistent metadata, whether internal or
external, will hang on the first write.
This is caused by commit 070dc6dd71
In that case, MD_CHANGE_PENDING never gets cleared.
So during md_update_sb, is neither persistent or external,
clear MD_CHANGE_PENDING.
This is suitable for 2.6.36-stable.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: enable unmappable vram for evergreen
drm/radeon/kms: fix tiled db height calculation on 6xx/7xx
drm/radeon/kms: fix handling of tex lookup disable in cs checker on r2xx
Commit eab6d18d "vlan: Don't check for vlan group before
vlan_tx_tag_present" removed the need for the adapter variable
in igb_xmit_frame_ring_adv(). This removes the variable as well
to avoid the compiler warning.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to iterative over every single irq_desc when we can
already work out which IRQs have a backing descriptor via the shiny new
for_each_active_irq(). Switch to that instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (48 commits)
DMAENGINE: move COH901318 to arch_initcall
dma: imx-dma: fix signedness bug
dma/timberdale: simplify conditional
ste_dma40: remove channel_type
ste_dma40: remove enum for endianess
ste_dma40: remove TIM_FOR_LINK option
ste_dma40: move mode_opt to separate config
ste_dma40: move channel mode to a separate field
ste_dma40: move priority to separate field
ste_dma40: add variable to indicate valid dma_cfg
async_tx: make async_tx channel switching opt-in
move async raid6 test to lib/Kconfig.debug
dmaengine: Add Freescale i.MX1/21/27 DMA driver
intel_mid_dma: change the slave interface
intel_mid_dma: fix the WARN_ONs
intel_mid_dma: Add sg list support to DMA driver
intel_mid_dma: Allow DMAC2 to share interrupt
intel_mid_dma: Allow IRQ sharing
intel_mid_dma: Add runtime PM support
DMAENGINE: define a dummy filter function for ste_dma40
...
* 'viafb-next' of git://github.com/schandinat/linux-2.6: (29 commits)
viafb: add initial VX900 support
viafb: fix hardware acceleration for suspend & resume
viafb: make suspend and resume work (on all machines?)
viafb: restore display on resume
Minimal support for viafb suspend/resume
viafb: use proper register for colour when doing fill ops
viafb: add documentation for proc interface
viafb: rename output devices
viafb: add a mapping of supported output devices
viafb: set sync polarity for all output devices
viafb: add function to change sync polarity per device
viafb: reduce I2C timeout and delay
viafb: enable I2C for CRT
viafb: fix i2c_transfer error handling
viafb: vt1636 cleanup
viafb: introduce per output device power management
viafb: limit LCD code impact
viafb: add interface for output device configuration
viafb: merge the remaining output path with enable functions
viafb: use new device routing
...
* git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-mn10300: (44 commits)
MN10300: Save frame pointer in thread_info struct rather than global var
MN10300: Change "Matsushita" to "Panasonic".
MN10300: Create a defconfig for the ASB2364 board
MN10300: Update the ASB2303 defconfig
MN10300: ASB2364: Add support for SMSC911X and SMC911X
MN10300: ASB2364: Handle the IRQ multiplexer in the FPGA
MN10300: Generic time support
MN10300: Specify an ELF HWCAP flag for MN10300 Atomic Operations Unit support
MN10300: Map userspace atomic op regs as a vmalloc page
MN10300: And Panasonic AM34 subarch and implement SMP
MN10300: Delete idle_timestamp from irq_cpustat_t
MN10300: Make various interrupt priority settings configurable
MN10300: Optimise do_csum()
MN10300: Implement atomic ops using atomic ops unit
MN10300: Make the FPU operate in non-lazy mode under SMP
MN10300: SMP TLB flushing
MN10300: Use the [ID]PTEL2 registers rather than [ID]PTEL for TLB control
MN10300: Make the use of PIDR to mark TLB entries controllable
MN10300: Rename __flush_tlb*() to local_flush_tlb*()
MN10300: AM34 erratum requires MMUCTR read and write on exception entry
...
In autoclear mode bdev is NULL but the sysfs
entry should be destroyed otherwise this warning appears:
WARNING: at fs/sysfs/dir.c:451 sysfs_add_one+0x82/0x95()
sysfs: cannot create duplicate filename '/devices/virtual/block/loop0/loop'
Fixes commit ee86273062
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'module' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
NULL-terminate all pci_device_id tables
(trivial) Fix compiler warning in kernel/modules.c
* akpm-incoming-2: (139 commits)
epoll: make epoll_wait() use the hrtimer range feature
select: rename estimate_accuracy() to select_estimate_accuracy()
Remove duplicate includes from many files
ramoops: use the platform data structure instead of module params
kernel/resource.c: handle reinsertion of an already-inserted resource
kfifo: fix kfifo_alloc() to return a signed int value
w1: don't allow arbitrary users to remove w1 devices
alpha: remove dma64_addr_t usage
mips: remove dma64_addr_t usage
sparc: remove dma64_addr_t usage
fuse: use release_pages()
taskstats: use real microsecond granularity for CPU times
taskstats: split fill_pid function
taskstats: separate taskstats commands
delayacct: align to 8 byte boundary on 64-bit systems
delay-accounting: reimplement -c for getdelays.c to report information on a target command
namespaces Kconfig: move namespace menu location after the cgroup
namespaces Kconfig: remove the cgroup device whitelist experimental tag
namespaces Kconfig: remove pointless cgroup dependency
namespaces Kconfig: make namespace a submenu
...
The BKL was pushed into this function when it was converted to use the
unlocked_ioctl interface, but nothing that the function touches is
actually protected by the BKL. So just remove the BKL entirely, so that
we finally can get a realistic system build without the BKL being
enabled at all.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Evergreen now has blit support, but unmappable vram support
was disabled in c919b371cb
(drm/radeon/kms: avoid corner case issue with unmappable vram V2)
due to merge ordering. This re-enables unmappable vram on
evergreen.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Calculate height based on the slice bitfield rather than the size.
Same as Dave's CB fix.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There are cases when multiple texture units have to be enabled,
but not actually used to sample. This patch checks to see if
the lookup_disable bit is set and if so, skips the texture check.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=25544
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
As each board and system has different memory for ramoops. It's better to
define the platform data instead of module params.
[akpm@linux-foundation.org: fix ramoops_remove() return type]
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marco Stornelli <marco.stornelli@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The search/pullup/add/remove device attributes were 0666 which would allow
arbitrary users to affect the 1 wire bus. Change to 0664 to prevent that.
I found this patch in the Android tree, apparently this has never been
sent upstream so doing it now.
Signed-off-by: Brian Swetland <swetland@google.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace possibly damaging broadcast writes into the per-port SP_MODE
registers with individual writes for each port. This will preserve
individual port configurations in case if ports are configured
differently.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace hardcoded maximum port number with actual reported number of
switch ports.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
RapidIO spec v.2.1 adds Idle Sequence 2 into LP-Serial Physical Layer.
The fix ensures that corresponding bits are not corrupted during error
handling.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Detects RIO link to the already enumerated device and properly sets links
between device objects. Changes to the enumeration/discovery logic:
1. Use Master Enable bit to signal end of the enumeration - agents may
start their discovery process as soon as they see this bit set
(Component Tag register was used before for this purpose).
2. Enumerator sets Component Tag (!= 0) immediately during device
setup. This allows to identify the device if the redundant route
exists in a RIO system.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the RIO switch driver and definitions for IDT CPS-1848 and CPS-1616
Gen2 devices.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add explicit device access check before performing device enumeration.
This gives a chance to clear possible link error conditions by issuing
safe maintenance read request(s).
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add check for access to port-write (PW) message source device before
processing the PW message. If source RIO device is not available (power
down or RIO link failure) trace back to a last available switch/port on
the PW message route and service failure at that point.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. Change to create attribute "routes" only for switches.
2. Add a switch-specific callback to create/remove proprietary attributes.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The default error-stopped state handler provides recovery mechanism as
defined by RIO specification.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Create back and forward links between RIO devices. These links are
intended for use by error management and hot-plug extensions. Links for
redundant RIO connections between switches are not set (will be fixed in a
separate patch).
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The switch port information is obtained and stored during RIO device
setup. Therefore repeated reads from Switch Port Information CAR may be
removed.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This set of RapidIO patches extends support for standard error recovery
mechanism and adds new IDT Gen2 sRIO switch devices - CPS-1848 and
CPS-1616. Implementation of the standard error-stopped state recovery
mechanism (as defined by the RapidIO specification) is required for the
new switches.
Version 2 of this set of patches addresses received comments and fixes an
error notification setup issue found in the idt_gen2.c after the first
version was released.
This patch:
Make RapidIO devices appear in /sys/devices/rapidio directory instead of
top of /sys/devices directory.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both mxser_disable_must_enchance_mode() and mxser_get_must_hardware_id()
called from function CheckIsMoxaMust(), when CONFIG_PCI=y. So mark both
the functions under CONFIG_PCI.
We were warned by the following warning.
drivers/char/mxser.c:306: warning: `mxser_disable_must_enchance_mode' defined but not used
drivers/char/mxser.c:391: warning: `mxser_get_must_hardware_id'
defined but not used
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changed <module>-objs to <module>-y in Makefile and use
ccflags-y option.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for extended byte synchronous mode feature of hardware.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Structures tmp_params and new_line are copied to userland with some
padding fields unitialized. It leads to leaking of stack memory.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Acked-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Structure par_timeout is copied to userland with some padding fields
unitialized. Field tv_usec has type __kernel_suseconds_t, it differs from
tv_sec's type on some architectures. It leads to leaking of stack memory.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Structure st_loc is copied to userland with some fields unitialized. It
leads to leaking of stack memory.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a long standing bug with per device locking.
Each device has an associated spinlock for synchronizing access to
hardware and state information with the ISR. A single hardware card has
one or more devices.
Bug: Non ISR code correctly acquires and releases the per device lock.
ISR incorrectly always acquires and releases the lock of the first device
on the card.
The decoupled and list based nature of the ISR and deferred processing
interaction allowed this to work in normal operation. Exceptional events
like an application forcing hardware shutdown, reset, or reconfiguration
while active can trigger the bug.
Fixed ISR to acquire and release the per device lock.
One exception is manipulation of the GPIO card resource which is global
and effectively owned by the first device of the card. Non-ISR access to
GPIO resource is changed to use lock of first device on card.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch for SGI Altix/IA64 eliminates interval long timer holdoffs in
cases where we don't start an interval timer before the expiration time.
This sometimes happens when a number of interval timers on the same shub
with the same interval run simultaneously.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This doesn't do anything.
Cc: Timur Tabi <timur@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Amit Shah <amit.shah@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There was a release_region() missing on the error path.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__init and __exit belong after the return type on functions, not
before.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Untested, but looks like an obvious typo to me.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Cc: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This code is preceded by a call to framebuffer_alloc, which allocates
memory, so this memory should be freed before leaving the function in an
error case. out_release_framebuffer just frees the frame buffer and
returns.
A simplified version of the semantic match that finds this problem is:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression x;
expression E;
identifier f1;
iterator I;
@@
x = framebuffer_alloc(...);
<... when != x
when != true (x == NULL || ...)
when != if (...) { <+...x...+> }
when != I (...) { <+...x...+> }
(
x == NULL
|
x == E
|
x->f1
)
...>
* return ...;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fb_{read,write} access the framebuffer using lots of fb_{read,write}l's
but don't check that the file position is aligned which can cause problems
on some architectures which do not support unaligned accesses.
Since the operations are essentially memcpy_{from,to}io, new
fb_memcpy_{from,to}fb macros have been defined and these are used instead.
For Sparc, fb_{read,write} macros use sbus_{read,write}, so this defines
new sbus_memcpy_{from,to}io functions the same as memcpy_{from,to}io but
using sbus_{read,write}b instead of {read,write}b.
Signed-off-by: James Hogan <james@albanarts.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change a few lines of indentation to tabs.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function has an unsigned return type, but returns a negative constant
to indicate an error condition. The result of calling the function is
only tested by comparison to 0, and thus unsigned is not needed and can be
dropped from the return type.
A sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@exists@
identifier f;
constant C;
@@
unsigned f(...)
{ <+...
* return -C;
...+> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I tested savagefb on 3 different Savage 4 cards:
Diamond Stealth III S520
Number Nine SR9
Datapath Horizon 2S (two savage chips on a PCI card)
it worked except the DDC which did not work on any of them.
Looking at the BIOS code, it does not use MMIO register 0xff20 but CRT
register 0xa0 or 0xb1 - depending on the chip revision and something in
register 0xa6. With this patch, DDC works fine on all 3 cards (even on
the second head of Horizon 2S - although it does not display anything as
it's misconfigured because of missing BIOS).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CONFIG_FB_MATROX_G ifdef isn't necessary at this point, because it is
checked in an outer ifdef level already and has no effect here.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In this case the logic is very similar but the IRQs are not exposed and
the device is not picked up via PCI
Based on a separate internal whitney point driver by Yin Kangkai.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Yin Kangkai <kangkai.yin@intel.com>
Cc: Alek Du <alek.du@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Deweird this driver.
Cc: Alek Du <alek.du@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Topcliff PCH is the platform controller hub that is going to be used in
Intel's upcoming general embedded platform. All IO peripherals in
Topcliff PCH are actually devices sitting on AMBA bus. Topcliff PCH has
GPIO I/F. Using this I/F, it is able to access system devices connected
to GPIO.
[akpm@linux-foundation.org: ese DEFINE_PCI_DEVICE_TABLE (per Joe Perches)]
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Tomoya MORINAGA <morinaga526@dsn.okisemi.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement irq_chip functionality on ADP5588/5587 GPIO expanders. Only
level sensitive interrupts are supported. Interrupts provided by this
irq_chip must be requested using request_threaded_irq().
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for generic 74x164 serial-in/parallel-out 8-bits shift
register. This driver can be used as a GPIO output expander.
[akpm@linux-foundation.org: remove unused local `refresh']
Signed-off-by: Miguel Gaio <miguel.gaio@efixo.com>
Signed-off-by: Juhos Gabor <juhosg@openwrt.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some versions of the hardware can trash the IER register if simultaneous
interrupts occur. This patch works around it by using a local copy of the
register and restoring it after every interrupt.
Signed-off-by: Tomas Hallenberg <tomas.hallenberg@pelagicore.com>
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The basic GPIO controllers may be found in various on-board FPGA and ASIC
solutions that are used to control board's switches, LEDs, chip-selects,
Ethernet/USB PHY power, etc.
These controllers may not provide any means of pin setup
(in/out/open drain).
The driver supports:
- 8/16/32/64 bits registers;
- GPIO controllers with clear/set registers;
- GPIO controllers with a single "data" register;
- Big endian bits/GPIOs ordering (mostly used on PowerPC).
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>,
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the "alarm" function to the jz4740 RTC. Interrupts will now be raised
when the "alarm" time is reached.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The DS3232 RTC driver only has the tick function. Add an alarm function
so the driver is complete.
Signed-off-by: Lan Chunhe-B25806 <b25806@freescale.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add "rtc_valid_tm" in s3c_rtc_gettime() as per Wan ZongShun's suggestion.
Suggested-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change RTC initialization method in probe(). The 'rtc_valid_tm(tm)' can
check whether RTC BCD is valid or not. And change the method of checking
because the previous method cannot validate RTC BCD registers properly.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The alarm_irq_enable function should be implemented to support RTC alarm.
And fix tabs instead of white space around the proc field.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Current s3c_rtc_getalarm() sets missing field of alarm time with 0xff.
But this value should be -1 according to drivers/rtc/interface.c.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
S3C2410_RTCCON of TYPE_S3C64XX RTC should be read/written by readw and
writew, because TYPE_S3C64XX RTC uses bit 8 and 9. And TYPE_S3C2410 RTC
also can access it by readw and writew.
[atul.dahiya@samsung.com: tested on smdk2416]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Tested-by: Atul Dahiya <atul.dahiya@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rtc-omap driver currently hardcodes the RTC wakeup capability to be
"not capable". While this seems to be true for existing OMAP1 boards
which are not wired for this, the DA850/OMAP-L138 SoC, the RTC can always
be wake up source from its "deep sleep" mode.
This patch lets the wakeup capability be set from platform data and does
not override the setting from the driver. For DA850/OMAP-L138, this is
done from arch/arm/mach-davinci/devices-da8xx.c:da8xx_register_rtc()
Note that this patch does not change the behavior on any existing OMAP1
board since the platform device registration sets the wakeup capability to
0 by default.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If device_register() fails then call put_device(). See comment to
device_register.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rest of the driver had debug markings already. This also standardizes
the usage of "dev" a bit.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
By unifying the RTC_ISTAT clearing steps, we shrink the interrupt handler
and avoid multiple writes to the hardware registers.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an RTC driver for the built-in RTC in the LPC32XX SoC. This patch
includes updates from the initial review comments and updates from the v3
review.
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Durgesh Pattamatta <durgesh.pattamatta@nxp.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When all VT's are in use, VT_OPENQRY casts -1 to unsigned char before
returning it to userspace as an int. VT255 is not the next available
console.
Signed-off-by: Graham Gower <graham.gower@gmail.com>
Cc: Greg KH <greg@kroah.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Put basic system information in the dmesg log. There are lots of dmesg
logs on the web, and it would be useful if they contained this information
for debugging platform problems. "BOARD/PRODUCT" format copied from
show_regs_common(), which is used in the oops path.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(Applied over Eric's "ehea: fix use after free" patch)
Currently ehea stats are broken. The bytes counters are got from
the hardware, while the packets counters are got from the device
driver. Also, the device driver counters are resetted during the
the down process, and the hardware aren't, causing some weird
numbers.
This patch just consolidates the packets and bytes on the device
driver.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ath5k_hw_attach fails it will free sc->ah (local variable ah) before
returning. However, when it reports failure the caller (ath5k_pci_probe)
will also free sc->ah. Let the caller handle the deallocation, it does
so on further errors as well.
Signed-off-by: Jones Desougi <jones.desougi@27m.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Netgear WNDA3200 device uses ar7010 firmware but it is failed to set
correct firmware offset on firmware download which causes device initialization
failure.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Completing aggregate frames can lead to new buffers being pushed into
the tid queues due to software retransmission.
When the tx queues are being drained, all pending aggregates must be
completed before the tid queues get drained, otherwise buffers might be
leaked.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Apart from locking the start and stop PCU we need
to ensure we also content starting and stopping the PCU
between hardware resets.
This is part of a series that will help resolve the bug:
https://bugzilla.kernel.org/show_bug.cgi?id=14624
For more details about this issue refer to:
http://marc.info/?l=linux-wireless&m=128629803703756&w=2
Cc: stable@kernel.org
Cc: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The real way to lock RX is to contend on the PCU
and reset, this will be fixed in the next patch but for
now just do the renames so that the next patch which changes
the locking order is crystal clear.
This is part of a series that will help resolve the bug:
https://bugzilla.kernel.org/show_bug.cgi?id=14624
For more details about this issue refer to:
http://marc.info/?l=linux-wireless&m=128629803703756&w=2
Cc: stable@kernel.org
Cc: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark Brown