Pull x86 fixes from Thomas Gleixner:
"A couple of fixlets for x86:
- Fix the ESPFIX double fault handling for 5-level pagetables
- Fix the commandline parsing for 'apic=' on 32bit systems and update
documentation
- Make zombie stack traces reliable
- Fix kexec with stack canary
- Fix the delivery mode for APICs which was missed when the x86
vector management was converted to single target delivery. Caused a
regression due to the broken hardware which ignores affinity
settings in lowest prio delivery mode.
- Unbreak modules when AMD memory encryption is enabled
- Remove an unused parameter of prepare_switch_to"
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Switch all APICs to Fixed delivery mode
x86/apic: Update the 'apic=' description of setting APIC driver
x86/apic: Avoid wrong warning when parsing 'apic=' in X86-32 case
x86-32: Fix kexec with stack canary (CONFIG_CC_STACKPROTECTOR)
x86: Remove unused parameter of prepare_switch_to
x86/stacktrace: Make zombie stack traces reliable
x86/mm: Unbreak modules that use the DMA API
x86/build: Make isoimage work on Debian
x86/espfix/64: Fix espfix double-fault handling on 5-level systems
Some of the APIC incarnations are operating in lowest priority delivery
mode. This worked as long as the vector management code allocated the same
vector on all possible CPUs for each interrupt.
Lowest priority delivery mode does not necessarily respect the affinity
setting and may redirect to some other online CPU. This was documented
somewhere in the old code and the conversion to single target delivery
missed to update the delivery mode of the affected APIC drivers which
results in spurious interrupts on some of the affected CPU/Chipset
combinations.
Switch the APIC drivers over to Fixed delivery mode and remove all
leftovers of lowest priority delivery mode.
Switching to Fixed delivery mode is not a problem on these CPUs because the
kernel already uses Fixed delivery mode for IPIs. The reason for this is
that th SDM explicitely forbids lowest prio mode for IPIs. The reason is
obvious: If the irq routing does not honor destination targets in lowest
prio mode then an IPI targeted at CPU1 might end up on CPU0, which would be
a fatal problem in many cases.
As a consequence of this change, the apic::irq_delivery_mode field is now
pointless, but this needs to be cleaned up in a separate patch.
Fixes: fdba46ffb4 ("x86/apic: Get rid of multi CPU affinity")
Reported-by: vcaputo@pengaru.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: vcaputo@pengaru.com
Cc: Pavel Machek <pavel@ucw.cz>
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1712281140440.1688@nanos
If CONFIG_DEBUG_SLAB=y, and no PCIe card is inserted, the kernel crashes
during probe on r8a7791/koelsch:
rcar-pcie fe000000.pcie: PCIe link down
Unable to handle kernel paging request at virtual address 6b6b6b6b
(seeing this message requires earlycon and keep_bootcon).
Indeed, pci_free_host_bridge() frees the PCI host bridge, including the
embedded rcar_pcie object, so pci_free_resource_list() must not be called
afterwards.
To fix this, move the call to pci_free_resource_list() up, and update the
label name accordingly.
Fixes: ddd535f1ea ("PCI: rcar: Fix memory leak when no PCIe card is inserted")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
* pci/host-tango:
PCI: tango: Add MSI controller support
PCI: Use of_pci_dma_range_parser_init() to reduce duplication
of/pci: Add of_pci_dma_range_parser_init() for dma-ranges parsing support
* pci/host-generic:
dt-bindings: PCI: designware: Add binding for Designware PCIe in ECAM mode
PCI: generic: Add support for Synopsys DesignWare RC in ECAM mode
Rename xgene_pcie_probe_bridge() to xgene_pcie_probe() to follow the
convention of other drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Rename xilinx_pcie_link_is_up() to xilinx_pcie_link_up() to follow the
convention of other drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Rename altera_pcie_link_is_up() to altera_pcie_link_up() to follow the
convention of other drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Ley Foon Tan <ley.foon.tan@intel.com>
The effective_affinity_mask is always set when an interrupt is assigned in
__assign_irq_vector() -> apic->cpu_mask_to_apicid(), e.g. for struct apic
apic_physflat: -> default_cpu_mask_to_apicid() ->
irq_data_update_effective_affinity(), but it looks d->common->affinity
remains all-1's before the user space or the kernel changes it later.
In the early allocation/initialization phase of an IRQ, we should use the
effective_affinity_mask, otherwise Hyper-V may not deliver the interrupt to
the expected CPU. Without the patch, if we assign 7 Mellanox ConnectX-3
VFs to a 32-vCPU VM, one of the VFs may fail to receive interrupts.
Tested-by: Adrian Suhov <v-adsuho@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jake Oshins <jakeo@microsoft.com>
Cc: stable@vger.kernel.org
Cc: Jork Loeser <jloeser@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PTR_ERR should access the value just tested by IS_ERR, otherwise the wrong
error code will be returned.
Fixes: 2eeb02b285 ("PCI: faraday: Add clock handling")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Add Tegra186 PCIe support. UPHY programming is performed by BPMP; PHY
enable calls are not required for Tegra186 PCIe.
Power partition ungate is done by BPMP powergate driver. The Tegra186
DT description must include a "power-domains" property, which results in
dev->pm_domain being set.
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
[bhelgaas: add "power-domains" reference]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Add support for allocating multiple MSIs at the same time, so that the
MSI_FLAG_MULTI_PCI_MSI flag can be added to the msi_domain_info structure.
Avoid storing the hwirq in the low 5 bits of the message data, as it is
used by the device. Also fix an endianness problem by using readl().
Signed-off-by: Sandor Bodo-Merle <sbodomerle@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
The Tegra PCI host controller can generate configuration space accesses
with byte, word and dword granularity for devices. Only root ports can't
have their configuration space accessed in this way.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
struct pci_host_bridge gained hooks to map/swizzle IRQs, so that the IRQ
mapping can be done automatically by PCI core code through the
pci_assign_irq() function instead of resorting to arch-specific
implementation callbacks to carry out the same task which force PCI host
bridge drivers implementation to implement per-arch kludges to carry out a
task that is inherently architecture agnostic.
Commit 769b461fc0 ("arm64: PCI: Drop DT IRQ allocation from
pcibios_alloc_irq()") was assuming all PCI host controller drivers had been
converted to use ->map_irq(), but that wasn't the case: pci-aardvark had
not been converted. Due to this, it broke the support for legacy PCI
interrupts when using the pci-aardvark driver (used on Marvell Armada 3720
platforms).
In order to fix this, we make sure the ->map_irq and ->swizzle_irq fields
of pci_host_bridge are properly filled in.
Fixes: 769b461fc0 ("arm64: PCI: Drop DT IRQ allocation from pcibios_alloc_irq()")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.13+
This reverts commit d7bd554f27.
It turns out that Tegra20 has a bug in the implementation of the MSI
target address register (which is worked around by the existence of the
struct tegra_pcie_soc.msi_base_shift parameter) that restricts the MSI
target memory to the lower 32 bits of physical memory on that particular
generation. The offending patch causes a regression on TrimSlice, which
is a Tegra20-based device and has a PCI network interface card.
An initial, simpler fix was to change the MSI target address for Tegra20
only, but it was pointed out that the offending commit also prevents the
use of 32-bit only MSI capable devices, even on later chips. Technically
this was never guaranteed to work with the prior code in the first place
because the allocated page could have resided beyond the 4 GiB boundary,
but it is still possible that this could've introduced a regression.
The proper fix that was settled on is to select a fixed address within
the lowest 32 bits of physical address space that is otherwise unused,
but testing of that patch has provided mixed results that are not fully
understood yet.
Given all of the above and the relative urgency to get this fixed in
v4.13, revert the offending commit until a universal fix is found.
Fixes: d7bd554f27 ("PCI: tegra: Do not allocate MSI target memory")
Reported-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Reported-by: Erik Faye-Lund <kusmabite@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # 4.13.x
Some implementations of the Synopsys DesignWare PCIe controller implement
a so-called ECAM shift mode, which allows a static memory window to be
configured that covers the configuration space of the entire bus range.
Usually, when the firmware performs all the low level configuration that is
required to expose this controller in a fully ECAM compatible manner, we
can simply describe it as "pci-host-ecam-generic" and be done with it.
However, in some cases (e.g., the Marvell Armada 80x0 as well as the
Socionext SynQuacer Soc), the IP was synthesized with an ATU window
granularity that does not allow the first bus to be mapped in a way that
prevents the device on the downstream port from appearing more than once,
and so we still need special handling in software to drive this static
almost-ECAM configuration.
So extend the pci-host-generic driver so it can support these controllers
as well, by adding special config space accessors that take the above quirk
into account.
Note that, unlike most drivers for this IP, this driver does not expose a
fake bridge device at B/D/F 00:00.0. There is no point in doing so, given
that this is not a true bridge, and does not require any windows to be
configured in order for the downstream device to operate correctly.
Omitting it also prevents the PCI resource allocation routines from handing
out BAR space to it unnecessarily.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[bhelgaas: factor out pci_dw_valid_device(), add pci_dw_ecam_map_bus() and
use generic read/write functions]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Will Deacon <will.deacon@arm.com>
This PCI host bridge from V3 Semiconductor needs no further
introduction. An ancient driver for it has been sitting in
arch/arm/mach-integrator/pci_v3.* since before v2.6.12 and the
initial migration to git.
But we need to get the drivers out of arch/arm/* and get proper handling of
the old drivers, rewrite and clean up so the PCI maintainer can control the
mass of drivers without having to run all over the kernel. We also switch
swiftly to all the new infrastructure found in the PCI hosts as of late.
Some code is preserved so I have added an extensive list of authors in the
top comment section.
This driver probes with the following result:
OF: PCI: host bridge /pciv3@62000000 ranges:
OF: PCI: No bus range found for /pciv3@62000000, using [bus 00-ff]
OF: PCI: IO 0x60000000..0x6000ffff -> 0x00000000
OF: PCI: MEM 0x40000000..0x4fffffff -> 0x40000000
OF: PCI: MEM 0x50000000..0x5fffffff -> 0x50000000
pci-v3-semi 62000000.pciv3: initialized PCI V3 Integrator/AP integration
pci-v3-semi 62000000.pciv3: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff]
pci_bus 0000:00: root bus resource [mem 0x50000000-0x5fffffff pref]
pci-v3-semi 62000000.pciv3: parity error interrupt
pci-v3-semi 62000000.pciv3: master abort error interrupt
pci-v3-semi 62000000.pciv3: PCI target LB->PCI READ abort interrupt
pci-v3-semi 62000000.pciv3: master abort error interrupt
(repeats a few times)
pci 0000:00:09.0: [1011:0024] type 01 class 0x060400
pci-v3-semi 62000000.pciv3: master abort error interrupt
pci-v3-semi 62000000.pciv3: PCI target LB->PCI READ abort interrupt
pci 0000:00:0b.0: [8086:1229] type 00 class 0x020000
pci 0000:00:0b.0: reg 0x10: [mem 0x00000000-0x00000fff pref]
pci 0000:00:0b.0: reg 0x14: [io 0x0000-0x001f]
pci 0000:00:0b.0: reg 0x18: [mem 0x00000000-0x000fffff]
pci 0000:00:0b.0: reg 0x30: [mem 0x00000000-0x000fffff pref]
pci 0000:00:0b.0: supports D1 D2
pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot
pci 0000:00:0c.0: [5333:8811] type 00 class 0x030000
pci 0000:00:0c.0: reg 0x10: [mem 0x00000000-0x03ffffff]
pci 0000:00:0c.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
pci 0000:00:0c.0: vgaarb: VGA device added: decodes=io+mem,owns=io,locks=none
PCI: bus0: Fast back to back transfers disabled
PCI: bus1: Fast back to back transfers enabled
pci 0000:00:0c.0: BAR 0: assigned [mem 0x40000000-0x43ffffff]
pci 0000:00:0b.0: BAR 2: assigned [mem 0x44000000-0x440fffff]
pci 0000:00:0b.0: BAR 6: assigned [mem 0x50000000-0x500fffff pref]
pci 0000:00:0c.0: BAR 6: assigned [mem 0x50100000-0x5010ffff pref]
pci 0000:00:0b.0: BAR 0: assigned [mem 0x50110000-0x50110fff pref]
pci 0000:00:0b.0: BAR 1: assigned [io 0x1000-0x101f]
pci 0000:00:09.0: PCI bridge to [bus 01]
pci 0000:00:0b.0: Firmware left e100 interrupts enabled; disabling
(...)
e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
e100 0000:00:0b.0: enabling device (0146 -> 0147)
e100 0000:00:0b.0 eth0: addr 0x50110000, irq 31, MAC addr 00:08:c7:99:d2:57
> lspci
00:0b.0 Class 0200: 8086:1229
00:09.0 Class 0604: 1011:0024
00:0c.0 Class 0300: 5333:8811
> cat /proc/iomem
40000000-4fffffff : V3 PCI NON-PRE-MEM
40000000-43ffffff : 0000:00:0c.0
44000000-440fffff : 0000:00:0b.0
44000000-440fffff : e100
50000000-5fffffff : V3 PCI PRE-MEM
50000000-500fffff : 0000:00:0b.0
50100000-5010ffff : 0000:00:0c.0
50110000-50110fff : 0000:00:0b.0
50110000-50110fff : e100
61000000-61ffffff : /pciv3@62000000
62000000-6200ffff : /pciv3@62000000
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[bhelgaas: fold in %pR fixes from Arnd Bergmann <arnd@arndb.de>:
http://lkml.kernel.org/r/20171011140224.3770968-1-arnd@arndb.de]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Add support for the MSI controller in Tango, which supports 256
message-signaled interrupts and a single doorbell address.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use the new of_pci_dma_range_parser_init() to reduce code duplication.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9cLP
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add enhanced Downstream Port Containment support, which prints more
details about Root Port Programmed I/O errors (Dongdong Liu)
- add Layerscape ls1088a and ls2088a support (Hou Zhiqiang)
- add MediaTek MT2712 and MT7622 support (Ryder Lee)
- add MediaTek MT2712 and MT7622 MSI support (Honghui Zhang)
- add Qualcom IPQ8074 support (Varadarajan Narayanan)
- add R-Car r8a7743/5 device tree support (Biju Das)
- add Rockchip per-lane PHY support for better power management (Shawn
Lin)
- fix IRQ mapping for hot-added devices by replacing the
pci_fixup_irqs() boot-time design with a host bridge hook called at
probe-time (Lorenzo Pieralisi, Matthew Minter)
- fix race when enabling two devices that results in upstream bridge
not being enabled correctly (Srinath Mannam)
- fix pciehp power fault infinite loop (Keith Busch)
- fix SHPC bridge MSI hotplug events by enabling bus mastering
(Aleksandr Bezzubikov)
- fix a VFIO issue by correcting PCIe capability sizes (Alex
Williamson)
- fix an INTD issue on Xilinx and possibly other drivers by unifying
INTx IRQ domain support (Paul Burton)
- avoid IOMMU stalls by marking AMD Stoney GPU ATS as broken (Joerg
Roedel)
- allow APM X-Gene device assignment to guests by adding an ACS quirk
(Feng Kan)
- fix driver crashes by disabling Extended Tags on Broadcom HT2100
(Extended Tags support is required for PCIe Receivers but not
Requesters, and we now enable them by default when Requesters support
them) (Sinan Kaya)
- fix MSIs for devices that use phantom RIDs for DMA by assuming MSIs
use the real Requester ID (not a phantom RID) (Robin Murphy)
- prevent assignment of Intel VMD children to guests (which may be
supported eventually, but isn't yet) by not associating an IOMMU with
them (Jon Derrick)
- fix Intel VMD suspend/resume by releasing IRQs on suspend (Scott
Bauer)
- fix a Function-Level Reset issue with Intel 750 NVMe by waiting
longer (up to 60sec instead of 1sec) for device to become ready
(Sinan Kaya)
- fix a Function-Level Reset issue on iProc Stingray by working around
hardware defects in the CRS implementation (Oza Pawandeep)
- fix an issue with Intel NVMe P3700 after an iProc reset by adding a
delay during shutdown (Oza Pawandeep)
- fix a Microsoft Hyper-V lockdep issue by polling instead of blocking
in compose_msi_msg() (Stephen Hemminger)
- fix a wireless LAN driver timeout by clearing DesignWare MSI
interrupt status after it is handled, not before (Faiz Abbas)
- fix DesignWare ATU enable checking (Jisheng Zhang)
- reduce Layerscape dependencies on the bootloader by doing more
initialization in the driver (Hou Zhiqiang)
- improve Intel VMD performance allowing allocation of more IRQ vectors
than present CPUs (Keith Busch)
- improve endpoint framework support for initial DMA mask, different
BAR sizes, configurable page sizes, MSI, test driver, etc (Kishon
Vijay Abraham I, Stan Drozd)
- rework CRS support to add periodic messages while we poll during
enumeration and after Function-Level Reset and prepare for possible
other uses of CRS (Sinan Kaya)
- clean up Root Port AER handling by removing unnecessary code and
moving error handler methods to struct pcie_port_service_driver
(Christoph Hellwig)
- clean up error handling paths in various drivers (Bjorn Andersson,
Fabio Estevam, Gustavo A. R. Silva, Harunobu Kurokawa, Jeffy Chen,
Lorenzo Pieralisi, Sergei Shtylyov)
- clean up SR-IOV resource handling by disabling VF decoding before
updating the corresponding resource structs (Gavin Shan)
- clean up DesignWare-based drivers by unifying quirks to update Class
Code and Interrupt Pin and related handling of write-protected
registers (Hou Zhiqiang)
- clean up by adding empty generic pcibios_align_resource() and
pcibios_fixup_bus() and removing empty arch-specific implementations
(Palmer Dabbelt)
- request exclusive reset control for several drivers to allow cleanup
elsewhere (Philipp Zabel)
- constify various structures (Arvind Yadav, Bhumika Goyal)
- convert from full_name() to %pOF (Rob Herring)
- remove unused variables from iProc, HiSi, Altera, Keystone (Shawn
Lin)
* tag 'pci-v4.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (170 commits)
PCI: xgene: Clean up whitespace
PCI: xgene: Define XGENE_PCI_EXP_CAP and use generic PCI_EXP_RTCTL offset
PCI: xgene: Fix platform_get_irq() error handling
PCI: xilinx-nwl: Fix platform_get_irq() error handling
PCI: rockchip: Fix platform_get_irq() error handling
PCI: altera: Fix platform_get_irq() error handling
PCI: spear13xx: Fix platform_get_irq() error handling
PCI: artpec6: Fix platform_get_irq() error handling
PCI: armada8k: Fix platform_get_irq() error handling
PCI: dra7xx: Fix platform_get_irq() error handling
PCI: exynos: Fix platform_get_irq() error handling
PCI: iproc: Clean up whitespace
PCI: iproc: Rename PCI_EXP_CAP to IPROC_PCI_EXP_CAP
PCI: iproc: Add 500ms delay during device shutdown
PCI: Fix typos and whitespace errors
PCI: Remove unused "res" variable from pci_resource_io()
PCI: Correct kernel-doc of pci_vpd_srdt_size(), pci_vpd_srdt_tag()
PCI/AER: Reformat AER register definitions
iommu/vt-d: Prevent VMD child devices from being remapping targets
x86/PCI: Use is_vmd() rather than relying on the domain number
...
* pci/host-vmd:
iommu/vt-d: Prevent VMD child devices from being remapping targets
x86/PCI: Use is_vmd() rather than relying on the domain number
x86/PCI: Move VMD quirk to x86 fixups
MAINTAINERS: Add Jonathan Derrick as VMD maintainer
PCI: vmd: Remove IRQ affinity so we can allocate more IRQs
PCI: vmd: Free up IRQs on suspend path
PCI: vmd: Assign vector zero to all bridges
PCI: vmd: Reserve IRQ pre-vector for better affinity
* pci/host-rockchip:
PCI: rockchip: Fix platform_get_irq() error handling
PCI: rockchip: Umap IO space if probe fails
PCI: rockchip: Remove IRQ domain if probe fails
PCI: rockchip: Disable vpcie0v9 if resume_noirq fails
PCI: rockchip: Clean up PHY if driver probe or resume fails
PCI: rockchip: Factor out rockchip_pcie_deinit_phys()
PCI: rockchip: Factor out rockchip_pcie_disable_clocks()
PCI: rockchip: Factor out rockchip_pcie_enable_clocks()
PCI: rockchip: Factor out rockchip_pcie_setup_irq()
PCI: rockchip: Use gpiod_set_value_cansleep() to allow reset via expanders
PCI: rockchip: Use PCI_NUM_INTX
PCI: rockchip: Explicitly request exclusive reset control
dt-bindings: phy-rockchip-pcie: Convert to per-lane PHY model
dt-bindings: PCI: rockchip: Convert to per-lane PHY model
arm64: dts: rockchip: convert PCIe to use per-lane PHYs for rk3339
PCI: rockchip: Idle inactive PHY(s)
phy: rockchip-pcie: Reconstruct driver to support per-lane PHYs
PCI: rockchip: Add per-lane PHY support
PCI: rockchip: Factor out rockchip_pcie_get_phys()
PCI: rockchip: Control optional 12v power supply
dt-bindings: PCI: rockchip: Add vpcie12v-supply for Rockchip PCIe controller
* pci/host-rcar:
PCI: rcar: Add device tree support for r8a7743/5
PCI: rcar: Fix memory leak when no PCIe card is inserted
PCI: rcar: Fix error exit path
* pci/host-mediatek:
PCI: mediatek: Use PCI_NUM_INTX
PCI: mediatek: Add MSI support for MT2712 and MT7622
PCI: mediatek: Use bus->sysdata to get host private data
dt-bindings: PCI: Add support for MT2712 and MT7622
PCI: mediatek: Add controller support for MT2712 and MT7622
dt-bindings: PCI: Cleanup MediaTek binding text
dt-bindings: PCI: Rename MediaTek binding
PCI: mediatek: Switch to use platform_get_resource_byname()
PCI: mediatek: Add a structure to abstract the controller generations
PCI: mediatek: Rename port->index and mtk_pcie_parse_ports()
PCI: mediatek: Use readl_poll_timeout() to wait for Gen2 training
PCI: mediatek: Explicitly request exclusive reset control
Apparently the PCIe capability is at address 0x40 in config space of X-Gene
v1 Root Ports. Add a definition of that and use the generic PCI_EXP_RTCTL
offset into the capability. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When platform_get_irq() fails we should propagate the real error value
instead of always returning -EINVAL.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Duc Dang <dhdang@apm.com>
When platform_get_irq() fails we should propagate the real error value
instead of always returning -EINVAL.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
When platform_get_irq() fails we should propagate the real error value
instead of always returning -EINVAL.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
platform_get_irq() returns a negative number on failure, so adjust the
logic to detect such condition and propagate the real error value on
failure.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ley Foon Tan <lftan@altera.com>
Linus Torvalds