Otherwise, the configured IPv6 address could be still "tentative"
at test time, possibly causing tests failures.
We can also drop some sleep along the code and decrease the
timeout for most commands so that the test runtime decreases.
v1 -> v2:
- fix comment (Stefano)
Fixes: d1f1b9cbf3 ("selftests: net: Introduce first PMTU test")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to dp83640 delay after soft reset
is needed to set up registers correctly.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running RISC-V QEMU with the Bochs device attached via PCIe the
probe of the Bochs device fails with:
[drm:bochs_hw_init] *ERROR* ID mismatch
This was introduced by this commit:
7780eb9ce8 bochs: convert to drm_dev_register
To fix the error we ensure that pci_enable_device() is called before
bochs_load().
Fixes: 7780eb9ce8 ("bochs: convert to drm_dev_register")
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reported-by: David Abdurachmanov <david.abdurachmanov@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190221003231.31625-1-alistair.francis@wdc.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The prepare_fb call always happens on new_plane_state.
The drm_atomic_helper_cleanup_planes checks to see if
plane state pointer has changed when deciding to call cleanup_fb on
either the new_plane_state or the old_plane_state.
For a non-async atomic commit the state pointer is swapped, so this
helper calls prepare_fb on the new_plane_state and cleanup_fb on the
old_plane_state. This makes sense, since we want to prepare the
framebuffer we are going to use and cleanup the the framebuffer we are
no longer using.
For the async atomic update helpers this differs. The async atomic
update helpers perform in-place updates on the existing state. They call
drm_atomic_helper_cleanup_planes but the state pointer is not swapped.
This means that prepare_fb is called on the new_plane_state and
cleanup_fb is called on the new_plane_state (not the old).
In the case where old_plane_state->fb == new_plane_state->fb then
there should be no behavioral difference between an async update
and a non-async commit. But there are issues that arise when
old_plane_state->fb != new_plane_state->fb.
The first is that the new_plane_state->fb is immediately cleaned up
after it has been prepared, so we're using a fb that we shouldn't
be.
The second occurs during a sequence of async atomic updates and
non-async regular atomic commits. Suppose there are two framebuffers
being interleaved in a double-buffering scenario, fb1 and fb2:
- Async update, oldfb = NULL, newfb = fb1, prepare fb1, cleanup fb1
- Async update, oldfb = fb1, newfb = fb2, prepare fb2, cleanup fb2
- Non-async commit, oldfb = fb2, newfb = fb1, prepare fb1, cleanup fb2
We call cleanup_fb on fb2 twice in this example scenario, and any
further use will result in use-after-free.
The simple fix to this problem is to block framebuffer changes
in the drm_atomic_helper_async_check function for now.
v2: Move check by itself, add a FIXME (Daniel)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Cc: <stable@vger.kernel.org> # v4.14+
Fixes: fef9df8b59 ("drm/atomic: initial support for asynchronous plane update")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/275364/
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Add a mechanism to only send commit done events once all pending
updates have been applied. This closes a small race window where
already armed events could fire even though the double buffered
hardware update just missed the update window.
- Add plane zpos property support to allow placing the overlay plane
behind the primary plane.
- Allow building imx-drm on all platforms under COMPILE_TEST.
-----BEGIN PGP SIGNATURE-----
iI4EABYIADYWIQRRO6F6WdpH1R0vGibVhaclGDdiwAUCXG/bAhgccGhpbGlwcC56
YWJlbEBnbWFpbC5jb20ACgkQ1YWnJRg3YsAz6wEA4ThGF7nvouYeI2jLEuLmkIpr
wXdyGA5XScfoSQUgFisBAPGl+g578KjIq7PrazKAEoKeencLytlf8mWCl99YZukB
=Veu5
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-next-2019-02-22' of git://git.pengutronix.de/pza/linux into drm-next
drm/imx: handle pending updates better, add plane zpos property support
- Add a mechanism to only send commit done events once all pending
updates have been applied. This closes a small race window where
already armed events could fire even though the double buffered
hardware update just missed the update window.
- Add plane zpos property support to allow placing the overlay plane
behind the primary plane.
- Allow building imx-drm on all platforms under COMPILE_TEST.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Philipp Zabel <pza@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20190222112350.m3ucezilqx6cyest@pengutronix.de
For platforms, which use a PHYS_OFFSET != 0, symbol _end also
contains that offset. So when calling memblock_reserve() for
reserving kernel the size argument needs to be adjusted.
Fixes: bcec54bf31 ("mips: switch to NO_BOOTMEM")
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # v4.20+
security_mmap_addr() does a capability check with current_cred(), but
we can reach this code from contexts like a VFS write handler where
current_cred() must not be used.
This can be abused on systems without SMAP to make NULL pointer
dereferences exploitable again.
Fixes: 8869477a49 ("security: protect from stack expansion into low vm addresses")
Cc: stable@kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In VRR mode, keep track of the vblank count of the last
completed pageflip in amdgpu_crtc->last_flip_vblank, as
recorded in the pageflip completion handler after each
completed flip.
Use that count to prevent mmio programming a new pageflip
within the same vblank in which the last pageflip completed,
iow. to throttle pageflips to at most one flip per video
frame, while at the same time allowing to request a flip
not only before start of vblank, but also anywhere within
vblank.
The old logic did the same, and made sense for regular fixed
refresh rate flipping, but in vrr mode it prevents requesting
a flip anywhere inside the possibly huge vblank, thereby
reducing framerate in vrr mode instead of improving it, by
delaying a slightly delayed flip requests up to a maximum
vblank duration + 1 scanout duration. This would limit VRR
usefulness to only help applications with a very high GPU
demand, which can submit the flip request before start of
vblank, but then have to wait long for fences to complete.
With this method a flip can be both requested and - after
fences have completed - executed, ie. it doesn't matter if
the request (amdgpu_dm_do_flip()) gets delayed until deep
into the extended vblank due to cpu execution delays. This
also allows clients which want to regulate framerate within
the vrr range a much more fine-grained control of flip timing,
a feature that might be useful for video playback, and is
very useful for neuroscience/vision research applications.
In regular non-VRR mode, retain the old flip submission
behavior. This to keep flip scheduling for fullscreen X11/GLX
OpenGL clients intact, if they use the GLX_OML_sync_control
extensions glXSwapBufferMscOML(, ..., target_msc,...) function
with a specific target_msc target vblank count.
glXSwapBuffersMscOML() or DRI3/Present PresentPixmap() will
not flip at the proper target_msc for a non-zero target_msc
if VRR mode is active with this patch. They'd often flip one
frame too early. However, this limitation should not matter
much in VRR mode, as scheduling based on vblank counts is
pretty futile/unusable under variable refresh duration
anyway, so no real extra harm is done.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With Micrel KSZ8061 PHY, the link may occasionally not come up after
Ethernet cable connect. The vendor's (Microchip, former Micrel) errata
sheet 80000688A.pdf descripes the problem and possible workarounds in
detail, see below.
The batch implements workaround 1, which permanently fixes the issue.
DESCRIPTION
Link-up may not occur properly when the Ethernet cable is initially
connected. This issue occurs more commonly when the cable is connected
slowly, but it may occur any time a cable is connected. This issue occurs
in the auto-negotiation circuit, and will not occur if auto-negotiation
is disabled (which requires that the two link partners be set to the
same speed and duplex).
END USER IMPLICATIONS
When this issue occurs, link is not established. Subsequent cable
plug/unplaug cycle will not correct the issue.
WORk AROUND
There are four approaches to work around this issue:
1. This issue can be prevented by setting bit 15 in MMD device address 1,
register 2, prior to connecting the cable or prior to setting the
Restart Auto-negotiation bit in register 0h. The MMD registers are
accessed via the indirect access registers Dh and Eh, or via the Micrel
EthUtil utility as shown here:
. if using the EthUtil utility (usually with a Micrel KSZ8061
Evaluation Board), type the following commands:
> address 1
> mmd 1
> iw 2 b61a
. Alternatively, write the following registers to write to the
indirect MMD register:
Write register Dh, data 0001h
Write register Eh, data 0002h
Write register Dh, data 4001h
Write register Eh, data B61Ah
2. The issue can be avoided by disabling auto-negotiation in the KSZ8061,
either by the strapping option, or by clearing bit 12 in register 0h.
Care must be taken to ensure that the KSZ8061 and the link partner
will link with the same speed and duplex. Note that the KSZ8061
defaults to full-duplex when auto-negotiation is off, but other
devices may default to half-duplex in the event of failed
auto-negotiation.
3. The issue can be avoided by connecting the cable prior to powering-up
or resetting the KSZ8061, and leaving it plugged in thereafter.
4. If the above measures are not taken and the problem occurs, link can
be recovered by setting the Restart Auto-Negotiation bit in
register 0h, or by resetting or power cycling the device. Reset may
be either hardware reset or software reset (register 0h, bit 15).
PLAN
This errata will not be corrected in the future revision.
Fixes: 7ab59dc15e ("drivers/net/phy/micrel_phy: Add support for new PHYs")
Signed-off-by: Alexander Onnasch <alexander.onnasch@landisgyr.com>
Signed-off-by: Rajasingh Thavamani <T.Rajasingh@landisgyr.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netif_msg_init() API takes on input the amount of bits to be set. The
description of debug parameter in the enc28j60 module is misleading in this
sense and passing 0xffff does not give an expected behaviour.
Fix the description of debug module parameter to show what exactly is expected.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1 << 31 is Undefined Behaviour according to the C standard.
Use U type modifier to avoid theoretical overflow.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have been reports of oversize UDP packets being sent to the
driver to be transmitted, causing error conditions. The issue is
likely caused by the dst of the SKB switching between 'lo' with
64K MTU and the hardware device with a smaller MTU. Patches are
being proposed by Mahesh Bandewar <maheshb@google.com> to fix the
issue.
In the meantime, add a quick length check in the driver to prevent
the error. The driver uses the TX packet size as index to look up an
array to setup the TX BD. The array is large enough to support all MTU
sizes supported by the driver. The oversize TX packet causes the
driver to index beyond the array and put garbage values into the
TX BD. Add a simple check to prevent this.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Logical block size is the lowest possible block size that the storage
device can address. Max segment size is often related with controller's
DMA capability. And it is reasonable to align max segment size with
logical block size.
SDHCI sets un-aligned max segment size, and causes ADMA error, so
fix it by aligning max segment size with logical block size.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: linux-block@vger.kernel.org
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Free up the allocated memory in the case of error return
The value of mmc_host->cqe_enabled stays 'false'. Thus, cqhci_disable
(mmc_cqe_ops->cqe_disable) won't be called to free the memory. Also,
cqhci_disable() seems to be designed to disable and free all resources, not
suitable to handle this corner case.
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is not enough space being allocated when DCMD is disabled.
CQE_DCMD is not necessary to be enabled when CQE is enabled.
(Software could halt CQE to send command)
In the case that CQE_DCMD is not enabled, it still needs to allocate
space for data transfer. For instance:
CQE_DCMD is enabled: 31 slots space (one slot used by DCMD)
CQE_DCMD is disabled: 32 slots space
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
scsi_device_quiesce() and scsi_device_resume() are called during
system-wide suspend and resume. scsi_device_quiesce() only succeeds for
SCSI devices that are in one of the RUNNING, OFFLINE or TRANSPORT_OFFLINE
states (see also scsi_set_device_state()). This patch avoids that the
following warning is triggered when resuming a system for which quiescing a
SCSI device failed:
WARNING: CPU: 2 PID: 11303 at drivers/scsi/scsi_lib.c:2600 scsi_device_resume+0x4f/0x58
CPU: 2 PID: 11303 Comm: kworker/u8:70 Not tainted 5.0.0-rc1+ #50
Hardware name: LENOVO 80E3/Lancer 5B2, BIOS A2CN45WW(V2.13) 08/04/2016
Workqueue: events_unbound async_run_entry_fn
Call Trace:
scsi_dev_type_resume+0x2e/0x60
async_run_entry_fn+0x32/0xd8
process_one_work+0x1f4/0x420
worker_thread+0x28/0x3c0
kthread+0x118/0x130
ret_from_fork+0x22/0x40
Cc: Przemek Socha <soprwa@gmail.com>
Reported-by: Przemek Socha <soprwa@gmail.com>
Fixes: 3a0a529971 ("block, scsi: Make SCSI quiesce and resume work reliably") # v4.15
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a request has its priority changed, we traverse the graph of all of
its signalers to raise their priorities to match (priority inheritance).
If the request has already started executing its payload, we know that
all of its signalers must have signaled and we do not need to process
our list of signalers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190226102404.29153-1-chris@chris-wilson.co.uk
In case of CQHCI, mrq->cmd may be NULL for data requests (non DCMD).
In such case mmc_should_fail_request is directly dereferencing
mrq->cmd while cmd is NULL.
Fix this by checking for mrq->cmd pointer.
Fixes: 72a5af554d ("mmc: core: Add support for handling CQE requests")
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
My console locks up as soon as Linux writes to [88800000,88f00000[
AFAIU, that memory area is reserved for trustzone.
Extend TZ reserved memory range, to prevent Linux from stepping on
trustzone's toes.
Cc: stable@vger.kernel.org # 4.20+
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Fixes: c783394956 ("arm64: dts: qcom: msm8998: Add smem related nodes")
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
When sending multicast messages via blocking socket,
if sending link is congested (tsk->cong_link_cnt is set to 1),
the sending thread will be put into sleeping state. However,
tipc_sk_filter_rcv() is called under socket spin lock but
tipc_wait_for_cond() is not. So, there is no guarantee that
the setting of tsk->cong_link_cnt to 0 in tipc_sk_proto_rcv() in
CPU-1 will be perceived by CPU-0. If that is the case, the sending
thread in CPU-0 after being waken up, will continue to see
tsk->cong_link_cnt as 1 and put the sending thread into sleeping
state again. The sending thread will sleep forever.
CPU-0 | CPU-1
tipc_wait_for_cond() |
{ |
// condition_ = !tsk->cong_link_cnt |
while ((rc_ = !(condition_))) { |
... |
release_sock(sk_); |
wait_woken(); |
| if (!sock_owned_by_user(sk))
| tipc_sk_filter_rcv()
| {
| ...
| tipc_sk_proto_rcv()
| {
| ...
| tsk->cong_link_cnt--;
| ...
| sk->sk_write_space(sk);
| ...
| }
| ...
| }
sched_annotate_sleep(); |
lock_sock(sk_); |
remove_wait_queue(); |
} |
} |
This commit fixes it by adding memory barrier to tipc_sk_proto_rcv()
and tipc_wait_for_cond().
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Incoming packets may have IP header checksum verified by the host.
They may not have IP header checksum computed after coalescing.
This patch re-compute the checksum when necessary, otherwise the
packets may be dropped, because Linux network stack always checks it.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
net: Fail route add with unsupported nexthop attribute
RTA_VIA was added for MPLS as a way of specifying a gateway from a
different address family. IPv4 and IPv6 do not currently support RTA_VIA
so using it leads to routes that are not what the user intended. Catch
and fail - returning a proper error message.
MPLS on the other hand does not support RTA_GATEWAY since it does not
make sense to have a nexthop from the MPLS address family. Similarly,
catch and fail - returning a proper error message.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
MPLS does not support nexthops with an MPLS address family.
Specifically, it does not handle RTA_GATEWAY attribute. Make it
clear by returning an error.
Fixes: 03c0566542 ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 currently does not support nexthops outside of the AF_INET6 family.
Specifically, it does not handle RTA_VIA attribute. If it is passed
in a route add request, the actual route added only uses the device
which is clearly not what the user intended:
$ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
$ ip ro ls
...
2001:db8:2::/64 dev eth0 metric 1024 pref medium
Catch this and fail the route add:
$ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
Error: IPv6 does not support RTA_VIA attribute.
Fixes: 03c0566542 ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 currently does not support nexthops outside of the AF_INET family.
Specifically, it does not handle RTA_VIA attribute. If it is passed
in a route add request, the actual route added only uses the device
which is clearly not what the user intended:
$ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
$ ip ro ls
...
172.16.1.0/24 dev eth0
Catch this and fail the route add:
$ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
Error: IPv4 does not support RTA_VIA attribute.
Fixes: 03c0566542 ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bpf/syscall.c, bpf_map_get_fd_by_id() use bpf_map_inc_not_zero()
to increase the refcount, both map->refcnt and map->usercnt. Then, if
bpf_map_new_fd() fails, should handle map->usercnt too.
Fixes: bd5f5f4ecb ("bpf: Add BPF_MAP_GET_FD_BY_ID")
Signed-off-by: Peng Sun <sironhide0null@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Check the infoframes and infoframe enable state when comparing two
crtc states.
We'll use the infoframe logging functions from video/hdmi.c to
show the infoframes as part of the state dump.
TODO: Try to better integrate the infoframe dumps with
drm state dumps
v2: drm_printk() is no more
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190225174106.2163-9-ville.syrjala@linux.intel.com
Read the HDMI infoframes from the hbuf and unpack them into
the crtc state.
Well, actually just AVI infoframe for now but let's write the
infoframe readout code in a more generic fashion in case we
expand this later.
Note that Daniel was sceptical about the benefit if this and
also concerned about the potential for crappy sdvo encoders not
implementing the hbuf read commands. My (admittedly limited)
experience is that such encoders don't implement even the
get/set hdmi encoding commands and thus would always be treated
as dvi only. Hence I believe this is safe, and also IMO preferable
having quirks to deal with missing readout support. The readout
support is neatly isolated in the sdvo code whereas the quirk
would leak to other parts of the driver (state checker, fastboot,
etc.) thus complicating the lives of other people.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190225174106.2163-8-ville.syrjala@linux.intel.com
As with regular HDMI encoders, let's precompute the infoframes
(actually just AVI infoframe for the time being) with SDVO HDMI
encoders.
v2: Drop the WARN_ON() from drm_hdmi_avi_infoframe_from_display_mode()
return since that could genuinely fail due to user asking
for incompatible aspect ratio
v3: .compute_config() now returns int
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190225174106.2163-7-ville.syrjala@linux.intel.com
Add code to read the infoframes from the video DIP and unpack them into
the crtc state.
v2: Make the read funcs return void (Daniel)
Drop the duplicate infoframe enabled checks (Daniel)
Add a FIXME for lspcon infoframe readout
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190225174106.2163-6-ville.syrjala@linux.intel.com
Store the infoframes in the crtc state and precompute them in
.compute_config(). While precomputing we'll also fill out the
inforames.enable bitmask appropriately.
v2: Drop the null packet stuff (Daniel)
Add a FIXME for lspcon
v3: .compute_config() now returns int
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190225174106.2163-5-ville.syrjala@linux.intel.com
Store the mask of enabled infoframes in the crtc state. We'll start
with just the readout for HDMI encoder, and we'll expand this
to compute the bitmask in .compute_config() later. SDVO will also
follow later.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190225174106.2163-4-ville.syrjala@linux.intel.com
We want to start tracking which infoframes are enabled, so let's replace
the boolean flag with a bitmask.
We'll abstract the bitmask so that it's not platform dependent. That
will allow us to examine the bitmask later in platform independent code.
v2: Don't map VIDEO_DIP_ENABLE to the null packet (Daniel)
Put a FIXME in the lspcon function
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190225174106.2163-3-ville.syrjala@linux.intel.com
This simplifies adding new query item objects.
v2: Use query_hdr (Tvrtko, Chris).
int instead of u32 in return (Tvrtko)
v3: More naming fixes (Tvrtko)
Signed-off-by: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190211173251.7131-1-abdiel.janulgue@linux.intel.com
Commit 57384592c4 ("iommu/vt-d: Store bus information in RMRR PCI
device path") changed the type of the path data, however, the change in
path type was not reflected in size calculations. Update to use the
correct type and prevent a buffer overflow.
This bug manifests in systems with deep PCI hierarchies, and can lead to
an overflow of the static allocated buffer (dmar_pci_notify_info_buf),
or can lead to overflow of slab-allocated data.
BUG: KASAN: global-out-of-bounds in dmar_alloc_pci_notify_info+0x1d5/0x2e0
Write of size 1 at addr ffffffff90445d80 by task swapper/0/1
CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 4.14.87-rt49-02406-gd0a0e96 #1
Call Trace:
? dump_stack+0x46/0x59
? print_address_description+0x1df/0x290
? dmar_alloc_pci_notify_info+0x1d5/0x2e0
? kasan_report+0x256/0x340
? dmar_alloc_pci_notify_info+0x1d5/0x2e0
? e820__memblock_setup+0xb0/0xb0
? dmar_dev_scope_init+0x424/0x48f
? __down_write_common+0x1ec/0x230
? dmar_dev_scope_init+0x48f/0x48f
? dmar_free_unused_resources+0x109/0x109
? cpumask_next+0x16/0x20
? __kmem_cache_create+0x392/0x430
? kmem_cache_create+0x135/0x2f0
? e820__memblock_setup+0xb0/0xb0
? intel_iommu_init+0x170/0x1848
? _raw_spin_unlock_irqrestore+0x32/0x60
? migrate_enable+0x27a/0x5b0
? sched_setattr+0x20/0x20
? migrate_disable+0x1fc/0x380
? task_rq_lock+0x170/0x170
? try_to_run_init_process+0x40/0x40
? locks_remove_file+0x85/0x2f0
? dev_prepare_static_identity_mapping+0x78/0x78
? rt_spin_unlock+0x39/0x50
? lockref_put_or_lock+0x2a/0x40
? dput+0x128/0x2f0
? __rcu_read_unlock+0x66/0x80
? __fput+0x250/0x300
? __rcu_read_lock+0x1b/0x30
? mntput_no_expire+0x38/0x290
? e820__memblock_setup+0xb0/0xb0
? pci_iommu_init+0x25/0x63
? pci_iommu_init+0x25/0x63
? do_one_initcall+0x7e/0x1c0
? initcall_blacklisted+0x120/0x120
? kernel_init_freeable+0x27b/0x307
? rest_init+0xd0/0xd0
? kernel_init+0xf/0x120
? rest_init+0xd0/0xd0
? ret_from_fork+0x1f/0x40
The buggy address belongs to the variable:
dmar_pci_notify_info_buf+0x40/0x60
Fixes: 57384592c4 ("iommu/vt-d: Store bus information in RMRR PCI device path")
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
In selftests/live_hangcheck, we have a lot of tests for resetting simple
spinners, but nothing quite prepared us for how the GPU reacted to
triggering a reset outside of the safe spinner. These two subtests fill
the ring with plain old empty, non-spinning requests, and then triggers
a reset. Without a user-payload to blame, these requests will exercise
the 'non-started' paths and mostly be replayed verbatim.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190226094922.31617-4-chris@chris-wilson.co.uk
Having weaned the interrupt handling off using a single global execution
queue, we no longer need to emit a global_seqno. Note that we still have
a few assumptions about execution order along engine timelines, but this
removes the most obvious artefact!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190226094922.31617-3-chris@chris-wilson.co.uk
To determine whether an engine has 'stuck', we simply check whether or
not is still on the same seqno for several seconds. To keep this simple
mechanism intact over the loss of a global seqno, we can simply add a
new global heartbeat seqno instead. As we cannot know the sequence in
which requests will then be completed, we use a primitive random number
generator instead (with a cycle long enough to not matter over an
interval of a few thousand requests between hangcheck samples).
The alternative to using a dedicated seqno on every request is to issue
a heartbeat request and query its progress through the system. Sadly
this requires us to reduce struct_mutex so that we can issue requests
without requiring that bkl.
v2: And without the extra CS_STALL for the hangcheck seqno -- we don't
need strict serialisation with what comes later, we just need to be sure
we don't write the hangcheck seqno before our batch is flushed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190226094922.31617-1-chris@chris-wilson.co.uk
In R-Car Gen2 or later, the maximum number of transfer blocks are
changed from 0xFFFF to 0xFFFFFFFF. Therefore, Block Count Register
should use iowrite32().
If another system (U-boot, Hypervisor OS, etc) uses bit[31:16], this
value will not be cleared. So, SD/MMC card initialization fails.
So, check for the bigger register and use apropriate write. Also, mark
the register as extended on Gen2.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: use max_blk_count in if(), add Gen2, update commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@kernel.org
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
[Ulf: Fixed build error]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The change to use dma_set_mask() incorrectly made a second call with the 32
bit DMA mask value when the call with the 64 bit DMA mask value succeeded.
Fixes: 453cd3700c ("scsi: hptiop: use dma_set_mask")
Cc: <stable@vger.kernel.org>
Suggested-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The change to use dma_set_mask_and_coherent() incorrectly made a second
call with the 32 bit DMA mask value when the call with the 64 bit DMA
mask value succeeded.
[mkp: fixed commit message]
Fixes: e4db40e7a1 ("scsi: hisi_sas: use dma_set_mask_and_coherent")
Cc: <stable@vger.kernel.org>
Suggested-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The change to use dma_set_mask_and_coherent() incorrectly made a second
call with the 32 bit DMA mask value when the call with the 64 bit DMA mask
value succeeded.
Fixes: c22b332d81 ("scsi: csiostor: switch to generic DMA API")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The change to use dma_set_mask_and_coherent() incorrectly made a second
call with the 32 bit DMA mask value when the call with the 64 bit DMA mask
value succeeded.
[mkp: fixed commit message]
Fixes: a69b080025 ("scsi: bfa: use dma_set_mask_and_coherent")
Cc: <stable@vger.kernel.org>
Suggested-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Paolo Abeni