The sunxi_sid driver currently uses a statically allocated nvmem_config
structure that is updated at probe time. This is sub-optimal as it
limits the driver to one instance, and also takes up space even if the
device is not present.
Modify the driver to allocate the nvmem_config structure at probe time,
plugging in the desired parameters along the way.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SID cells are 32-bit aligned, and a multiple of 32 bits in length. The
only outlier is the thermal sensor calibration data, which is 16 bits
per sensor. However a whole 64 bits is allocated for this purpose, so
we could consider it conforming to the rule above.
Also, the register read-out method assumes native endian, unlike the
direct MMIO method, which assumes big endian. Thus no endian conversion
is involved.
Under these assumptions, the register read-out method can be slightly
optimized. Instead of reading one word then discarding 3 bytes, read
the whole word directly into the buffer. However, for reads under 4
bytes or trailing bytes, we still use a scratch buffer to extract the
requested bytes.
We could go one step further if .word_size was 4, but changing that
would affect the sysfs interface's behavior.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the reg_read callbacks already support arbitrary, but 4-byte
aligned. offsets and lengths into the SID, there is no need for another
for loop just to use it to read 1 byte at a time.
Read out the whole SID block in one go.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The i.MX OCOTP controller is used in numerous Freescale/NXP
SoCs from the MXC family, so the strict dependency on the
i.MX6 SoC is too narrow. Broaden it to cover all the MXC
familiy members.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The i.MX8MQ uses the same OCOTP block as the i.MX7D, but with
fourfold increase in fuse banks.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver needs ZynqMP firmware interface to call EEMI
APIs. In case firmware is not ready, dependent drivers
should wait until the firmware is ready.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Here is the big char/misc driver patch pull request for 5.1-rc1.
The largest thing by far is the new habanalabs driver for their AI
accelerator chip. For now it is in the drivers/misc directory but will
probably move to a new directory soon along with other drivers of this
type.
Other than that, just the usual set of individual driver updates and
fixes. There's an "odd" merge in here from the DRM tree that they asked
me to do as the MEI driver is starting to interact with the i915 driver,
and it needed some coordination. All of those patches have been
properly acked by the relevant subsystem maintainers.
All of these have been in linux-next with no reported issues, most for
quite some time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXH+dPQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym1fACgvpZAxjNzoRQJ6f06tc8ujtPk9rUAnR+tCtrZ
9e3l7H76oe33o96Qjhor
=8A2k
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver patch pull request for 5.1-rc1.
The largest thing by far is the new habanalabs driver for their AI
accelerator chip. For now it is in the drivers/misc directory but will
probably move to a new directory soon along with other drivers of this
type.
Other than that, just the usual set of individual driver updates and
fixes. There's an "odd" merge in here from the DRM tree that they
asked me to do as the MEI driver is starting to interact with the i915
driver, and it needed some coordination. All of those patches have
been properly acked by the relevant subsystem maintainers.
All of these have been in linux-next with no reported issues, most for
quite some time"
* tag 'char-misc-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (219 commits)
habanalabs: adjust Kconfig to fix build errors
habanalabs: use %px instead of %p in error print
habanalabs: use do_div for 64-bit divisions
intel_th: gth: Fix an off-by-one in output unassigning
habanalabs: fix little-endian<->cpu conversion warnings
habanalabs: use NULL to initialize array of pointers
habanalabs: fix little-endian<->cpu conversion warnings
habanalabs: soft-reset device if context-switch fails
habanalabs: print pointer using %p
habanalabs: fix memory leak with CBs with unaligned size
habanalabs: return correct error code on MMU mapping failure
habanalabs: add comments in uapi/misc/habanalabs.h
habanalabs: extend QMAN0 job timeout
habanalabs: set DMA0 completion to SOB 1007
habanalabs: fix validation of WREG32 to DMA completion
habanalabs: fix mmu cache registers init
habanalabs: disable CPU access on timeouts
habanalabs: add MMU DRAM default page mapping
habanalabs: Dissociate RAZWI info from event types
misc/habanalabs: adjust Kconfig to fix build errors
...
blocking_notifier_call_chain() returns the value returned by the last
registered callback. A positive return value doesn't indicate an error
and an nvmem device should correctly register irrespective of any
notifier callback failures. Drop the retval check.
Fixes: bee1138bea ("nvmem: add a notifier chain")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds zynqmp nvmem firmware driver to access the
SoC revision information from the hardware register.
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The imx-ocotp nvmem driver supports the i.MX 7D SoC too. Allow to select
the imx-ocotp driver even if only the i.MX 7D SoC has been selected.
Fixes: 711d454779 ("nvmem: octop: Add i.MX7D support")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once the correct cell has been found there is no need to continue
iterating, just stop there. While at it replace the goto used to leave
the loop with simple break statements.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__nvmem_device_get() make use of bus_find_device() to get the relevant
device and this function increase the reference count of the device
found, however this is not accounted for anywhere. Fix
__nvmem_device_get() and __nvmem_device_put() to properly release this
reference count.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In nvmem_device_get(), when the device lookup fails with DT it
currently fallback on nvmem_find() which is wrong for two reasons.
First nvmem_find() return NULL when nothing is found instead of an
ERR_PTR. But nvmem_find() also just lookup the device, it doesn't
reference the module and increment the reference count like it is done
in the DT path.
To fix this we replace the call to nvmem_find() with a call to
__nvmem_device_get() which does all the referencing and return a
proper ERR_PTR in case of error.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_nvmem_device_get() would crash if NULL was passed as a connection
ID. Rework this to use the usual sementic of assuming the first
connection when no connection ID is given.
Furthermore of_nvmem_device_get() would return -EINVAL when it failed
to resolve the connection, making it impossible to properly implement
an optional connection. Return -ENOENT instead to let the caller know
that the connection doesn't exists.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the cell list is not empty and nvmem_find_cell_by_node/name() is
called for a cell that is not present in the list they will return an
invalid pointer instead of NULL. This happen because
list_for_each_entry() stop once it reach the list head again, but as
the list head is not contained in a struct nvmem_cell the iteration
variable then contains an invalid value.
This is easily solved by using a variable to iterate over the list and
one to return the cell found.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_nvmem_cell_get() should return -ENOENT when a cell isn't defined,
otherwise callers can't distinguish between a missing cell and other
errors.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If no write callback is given the device should be marked as read-only.
While at it also move from a bit or to a logical or as that is a logical
expression.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In comparision to the i.MX6UL the lower cost variants i.MX6ULL/ULZ only
supports 8 OTP banks a 8 words.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i.MX7ULP is a new SoC of i.MX family which has 8 kbit eFuse OTP,
enable ocotp driver support for this SoC.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ACPI support to bcm ocotp driver
This patch is based on Linux-4.20-rc7.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Spreadtrum SC27XX efuse data are organized by blocks and each block
contains 2 bytes data. Moreover the nvmem core always pass the offset
in byte to the controller, so we should change the offset in byte to
the correct block index and block offset to read the data.
Signed-off-by: Freeman Liu <freeman.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to add nvmem support for MTD. TI DaVinci is the first platform
that will be using it, but only in non-DT mode. In order not to
introduce any new interface to supporting of which we would have to
commit - add a new config option that tells nvmem not to use the DT
node of the parent device.
This way we won't be creating nvmem devices corresponding with MTD
partitions defined in device tree. By default MTD will set this new
field to true.
Once a set of bindings for MTD nvmem cells is agreed upon, we'll be
able to remove this option.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we put static variable to a header file it's copied to each module
that includes the header. But not all of them are actually using it.
Move nvmem_type_str array to its only user to make a compiler happy:
In file included from include/linux/rtc.h:18,
from drivers/rtc/rtc-proc.c:15:
include/linux/nvmem-provider.h:29:27: warning: 'nvmem_type_str'
defined but not used [-Wunused-const-variable=]
static const char * const nvmem_type_str[] = {
^~~~~~~~~~~~~~
Suggested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Suggested-by: Joe Perches <joe@perches.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get and enable the peripheral clock required by the efuse device.
The driver has been handle to work without it so far because the
clock was left enabled by default but it won't be the case soon.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a type attribute so userspace is able to know how the data is stored as
this can help taking the correct decision when selecting which device to
use. This will also help program display the proper warnings when burning
fuses for example.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NVMEM DT support seems to be totally broken after
commit e888d445ac ("nvmem: resolve cells from DT at registration time")
Fix this!
Index used in of_nvmem_cell_get() to find cell is specific to
consumer, It can not be used for searching the cell in provider.
Use device_node instead of this to find the matching cell in device
tree case.
Fixes: e888d445ac ("nvmem: resolve cells from DT at registration time")
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nvmem_find_cell_by_index() is only called from inside an #ifdef,
so we get a build warning without CONFIG_OF:
drivers/nvmem/core.c:496:1: error: 'nvmem_find_cell_by_index' defined but not used [-Werror=unused-function]
Move it into the same #ifdef as the caller to avoid the warning.
Fixes: e888d445ac ("nvmem: resolve cells from DT at registration time")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove a variable that's no longer used from lpc18xx_eeprom_remove().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We check if the pointer returned by __nvmem_device_get() is not NULL
while we should actually check if it is not IS_ERR(nvmem). Fix it.
While we're at it: fix the next error path where we should assign an
error value to cell before returning.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
[srinivas: rebased on top of next]
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now we have new api nvmem_add/del_cell_table() we do not want users to use
nvmem_add_cells() anymore. So mark it accordingly. I guess it was missed in
original cleanup patch.
This also fixes below warning:
core.c:355:5: warning: no previous prototype for 'nvmem_add_cells'
[-Wmissing-prototypes]
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The argument representing the cell name in the nvmem_cell_get() family
of functions is not consistend between function prototypes and
definitions. Name it 'id' in all those routines. This is in line with
other frameworks and can represent both the DT cell name from the
nvmem-cell-names property as well as the con_id field from cell
lookup entries.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a blocking notifier chain with four events (add and remove for
both devices and cells) so that users can get notified about the
addition of nvmem resources they're waiting for.
We'll use this instead of the at24 setup callback in the mityomapl138
board file.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a way for machine code users to associate devices with nvmem cells.
This restores the support for non-DT systems but following a different
approach. Cells must now be associated with devices using provided
routines and data structures before they can be retrieved using
nvmem_cell_get().
It's still possible to define cells statically in nvmem_config but
cells created this way still need to be associated with consumers using
lookup entries.
Note that nvmem_find() must be moved higher in the source file as we
want to call it from __nvmem_device_get() for devices that don't have
a device node.
The signature of __nvmem_device_get() is also changed as it's no longer
used to retrieve cells.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we're creating a new cell structure everytime a DT user
calls nvmem_cell_get().
Change this behavior by resolving the cells during nvmem provider
registration and adding all cells to the provider's list. Make
of_nvmem_cell_get() just parse the phandle and look the cell up
in the relevant provider's list.
Don't drop the cell in nvmem_cell_put().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new structs and routines allowing users to define nvmem cells from
machine code. This global list of entries is parsed when a provider
is registered and cells are associated with the relevant nvmem_device
struct.
A possible improvement for the future is to allow users to register
cell tables after the nvmem provider has been registered by updating
the cell list at each call to nvmem_(add|del)_cell_table().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nvmem subsystem keeps a global list of cells that, for non-DT systems,
can only be referenced by cell name, which makes it impossible to have
more than one nvmem device with cells named the same.
This patch makes every nvmem device the owner of the list of its cells.
This effectively removes the support for non-DT systems, but it will
be reintroduced following a different approach in subsequent patches.
This isn't a problem as support for board files in nvmem is currently
broken anyway: any user that would try to get an nvmem cell from the
global cell list would remove the cell after the calling
nvmem_cell_put(). This can cause anything from a subsequent user not
being able to get the cell to double free errors if more users hold
reference to the same cell at the same time.
Fortunately there are no such users which allows us to rework this part.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We switched the nvmem framework to using kref instead of manually
checking the current number of users in nvmem_unregister() so this
function can no longer fail. We also converted all remaining users
that still checked the return value of nvmem_unregister() to using
devm_nvmem_register(). Make the routine return void.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the managed version of nvmem_register().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver currently returns -EINVAL if kzalloc() fails in probe().
Change it to -ENOMEM as it should be.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use kref for reference counting. Use an approach similar to the one
seen in the common clock subsystem: don't actually destroy the nvmem
device until the last user puts it. This way we can get rid of the
users check from nvmem_unregister().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function can fail so check its return value in nvmem_register()
and act accordingly.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two empty lines between devm_nvmem_unregister() and
__nvmem_device_get(). Remove one.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the provided helper for iterating over list entries without having
to use the list_entry() macro.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This field is never set and is only used in a single error message.
Remove the field and use nvmem_dev_name() instead.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kernel users don't have any means of checking the names of nvmem
devices. Add a routine that returns the name of the nvmem provider.
This will be useful for future nvmem notifier subscribers - otherwise
they can't check what device is being added/removed.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nvmem_device_get() should return ERR_PTR() on error or valid pointer
on success, but one of the code path seems to return NULL, so fix it.
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i.MX6SLL is a new SoC of i.MX6 family, enable ocotp
driver support for this SoC.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add the efuse driver which is embeded in Spreadtrum SC27XX
series PMICs. The sc27xx efuse contains 32 blocks and each block's
data width is 16 bits.
Signed-off-by: Freeman Liu <freeman.liu@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nvmem ncells can be over written by calling nvmem_add_cells()
multiple times. I see there is no real point of maintaining count
of cells when we have a list of cell.
Remove this to avoid any confusion!
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the quest to remove all stack VLA usage from the kernel[1], this
uses the maximum allocation size for the stack and adds a sanity check,
similar to what has already be done for the regular rave-sp driver.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit ca04d9d3e1 ("phy: qcom-qusb2: New driver for QUSB2 PHY on
Qcom chips") you can see a call like:
devm_nvmem_cell_get(dev, NULL);
Note that the cell ID passed to the function is NULL. This is because
the qcom-qusb2 driver is expected to work only on systems where the
PHY node is hooked up via device-tree and is nameless.
This works OK for the most part. The first thing nvmem_cell_get()
does is to call of_nvmem_cell_get() and there it's documented that a
NULL name is fine. The problem happens when the call to
of_nvmem_cell_get() returns -EINVAL. In such a case we'll fall back
to nvmem_cell_get_from_list() and eventually might (if nvmem_cells
isn't an empty list) crash with something that looks like:
strcmp
nvmem_find_cell
__nvmem_device_get
nvmem_cell_get_from_list
nvmem_cell_get
devm_nvmem_cell_get
qusb2_phy_probe
There are several different ways we could fix this problem:
One could argue that perhaps the qcom-qusb2 driver should be changed
to use of_nvmem_cell_get() which is allowed to have a NULL name. In
that case, we'd need to add a patche to introduce
devm_of_nvmem_cell_get() since the qcom-qusb2 driver is using devm
managed resources.
One could also argue that perhaps we could just add a name to
qcom-qusb2. That would be OK but I believe it effectively changes the
device tree bindings, so maybe it's a no-go.
In this patch I have chosen to fix the problem by simply not crashing
when a NULL cell_id is passed to nvmem_cell_get().
NOTE: that for the qcom-qusb2 driver the "nvmem-cells" property is
defined to be optional and thus it's expected to be a common case that
we would hit this crash and this is more than just a theoretical fix.
Fixes: ca04d9d3e1 ("phy: qcom-qusb2: New driver for QUSB2 PHY on Qcom chips")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function nvmem_reg_read can return a non zero value indicating an error.
This returned value must be read and error propagated to
nvmem_cell_prepare_write_buffer. Silence the following gcc warning (W=1):
drivers/nvmem/core.c:1093:9: warning: variable 'rc' set but
not used [-Wunused-but-set-variable]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document dev parameter which not described in devm_nvmem_unregister
and devm_nvmem_register functions.
Fix below warnings when kernel is compiled with W=1
drivers/nvmem/core.c:579: warning: Function parameter or member
'dev' not described in 'devm_nvmem_register'
nvmem/core.c:615: warning: Function parameter or member 'dev'
not described in 'devm_nvmem_unregister'
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add write support to the meson-gx efuse driver.
Beware, this efuse is one time programmable !
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most of the code and variables in the read callback is not necessary.
Keep only what is required.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having a global structure holding a reference to the device
structure is not very nice. Allocate the econfig instead and fill
the nvmem information as before
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not all platforms use device tree. It is useful to be able to add
cells to a NVMEM device from code. Export nvmem_add_cells() so making
this possible.
This required changing the parameters a bit, so that just the cells
and the number of cells are passed, not the whole nvmem config
structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of char/misc driver patches for 4.17-rc1.
There are a lot of little things in here, nothing huge, but all
important to the different hardware types involved:
- thunderbolt driver updates
- parport updates (people still care...)
- nvmem driver updates
- mei updates (as always)
- hwtracing driver updates
- hyperv driver updates
- extcon driver updates
- and a handfull of even smaller driver subsystem and individual
driver updates
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsShSQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykNqwCfUbfvopswb1PesHCLABDBsFQChgoAniDa6pS9
kI8TN5MdLN85UU27Mkb6
=BzFR
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc driver patches for 4.17-rc1.
There are a lot of little things in here, nothing huge, but all
important to the different hardware types involved:
- thunderbolt driver updates
- parport updates (people still care...)
- nvmem driver updates
- mei updates (as always)
- hwtracing driver updates
- hyperv driver updates
- extcon driver updates
- ... and a handful of even smaller driver subsystem and individual
driver updates
All of these have been in linux-next with no reported issues"
* tag 'char-misc-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (149 commits)
hwtracing: Add HW tracing support menu
intel_th: Add ACPI glue layer
intel_th: Allow forcing host mode through drvdata
intel_th: Pick up irq number from resources
intel_th: Don't touch switch routing in host mode
intel_th: Use correct method of finding hub
intel_th: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate
stm class: Make dummy's master/channel ranges configurable
stm class: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate
MAINTAINERS: Bestow upon myself the care for drivers/hwtracing
hv: add SPDX license id to Kconfig
hv: add SPDX license to trace
Drivers: hv: vmbus: do not mark HV_PCIE as perf_device
Drivers: hv: vmbus: respect what we get from hv_get_synint_state()
/dev/mem: Avoid overwriting "err" in read_mem()
eeprom: at24: use SPDX identifier instead of GPL boiler-plate
eeprom: at24: simplify the i2c functionality checking
eeprom: at24: fix a line break
eeprom: at24: tweak newlines
eeprom: at24: refactor at24_probe()
...
The new of_get_nvmem_mac_address() helper function causes a link error
with CONFIG_NVMEM=m:
drivers/of/of_net.o: In function `of_get_nvmem_mac_address':
of_net.c:(.text+0x168): undefined reference to `of_nvmem_cell_get'
of_net.c:(.text+0x19c): undefined reference to `nvmem_cell_read'
of_net.c:(.text+0x1a8): undefined reference to `nvmem_cell_put'
I could not come up with a good solution for this, as the code is always
built-in. Using an #if IS_REACHABLE() check around it would solve the
link time issue but then stop it from working in that configuration.
Making of_nvmem_cell_get() an inline function could also solve that, but
seems a bit ugly since it's somewhat larger than most inline functions,
and it would just bring that problem into the callers. Splitting the
function into a separate file might be an alternative.
This uses the big hammer by making CONFIG_NVMEM itself a 'bool' symbol,
which avoids the problem entirely but makes the vmlinux larger for anyone
that might use NVMEM support but doesn't need it built-in otherwise.
Fixes: 9217e566bd ("of_net: Implement of_get_nvmem_mac_address helper")
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mike Looijmans
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that doing some operation will make the value pre-read on H3
SID controller wrong again, so all operation should be performed by
register.
Change the SID reading to use register only.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The i.MX7 family has similar SNVS hardware so make the snvs-lpgpr
support it along with the i.MX6 family. The register interface is the
same except for the number and offset of the general purpose registers.
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
meson_mx_efuse_read calculates the address internal to the eFuse based
on the offset and the word size. This works fine with any given offset.
However, the offset is also included when writing to the output buffer.
This means that reading 4 bytes at offset 500 tries to write beyond the
array allocated by the nvmem core as it wants to write the 4 bytes to
"buffer address + offset (500)".
This issue did not show up in the previous tests since no driver uses
any value from the eFuse yet and reading the eFuse via sysfs simply
reads the whole eFuse, starting at offset 0.
Fix this by only including the offset in the internal address
calculation.
Fixes: 8caef1fa91 ("nvmem: add a driver for the Amlogic Meson6/Meson8/Meson8b SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the necessary data for handling eFuse on the rk3328.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The eFuse size is defined in property <reg> before, but the length
of registers is not equal to the size on some platforms, so we
add a new property to redefine it.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The efuse on UniPhier allows 8bit access according to the specification.
Since bit offset of nvmem is limited to 0-7, it is desiable to change
access unit of nvmem to 8bit.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chen-Yu Tsai