The current code in the 'rt2800_adjust_freq_offset'
function limits the device specific frequency offset
value to FREQ_BOUND but ignores the fact that the
uppermost bit is not part of the frequency offset
value. As the result, the driver always uses the
FREQ_BOUND value if the uppermost bit is set.
Update the code to use the correct source value
for calculating the boundary.
Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
Reference:
RTMPAdjustFrequencyOffset function in common/rt_rf.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of precomputing the beacon base in
each caller, pass the beacon index to the
'rt2800_clear_beacon_register' function
and compute the beacon base in there.
This allows to simplify the caller functions
a bit.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The name of the HW_BEACON_OFFSET macro is a
bit confusing. It returns with one of the
HW_BEACON_BASE* values, so rename the macro
to HW_BEACON_BASE to reflect that.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we use struct efx_mtd to represent a physical NVRAM device
and struct efx_mtd_partition to represent a partition on that device.
But this only really makes sense for Falcon, as we don't know or care
whether MC-managed NVRAM partitions are on one or more physical
devices. It complicates iteration and provides little benefit.
Therefore:
- Replace the pointer to efx_mtd in mtd_info::priv with a pointer to efx_nic
- Move the falcon_spi_device pointer into the union in struct efx_mtd_partition
- Move the device name to efx_mtd_partition::dev_type_name
- Move the efx_mtd_ops pointer to efx_nic::mtd_ops
- Make efx_nic::mtd_list a list of partitions
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
On Falcon we implement MAC filtering requested by the stack using the
MAC wrapper's single unicast filter and multicast hash filter. Siena
is very similar, though MAC configuration is mediated by the MC.
Since MCDI operations may sleep, reconfiguration is deferred from
ndo_set_rx_mode to a work item. However, it still updates the private
variables describing the filter state synchronously. Contrary to
comments, the later use of these variables is not protected using the
address lock, resulting in race conditions.
Move the state update to a new function
efx_farch_filter_sync_rx_mode() and make the Falcon-arch MAC
configuration functions call that, so that its use is consistently
serialised by the mac_lock.
Invert and rename the promiscuous flag to the more accurate
unicast_filter, and comment that both this and multicast_hash are
not used on EF10.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
MAC filters inserted on request from the stack (ndo_set_rx_mode)
should allow manual steering but not removal. Currently we have a
special case for Siena's all-multicast and all-unicast MAC filters,
but on EF10 we need to allow for steering of precise MAC filters as
well.
The EFX_FILTER_FLAG_RX_STACK flag changes the behaviour of replacement
and removal requests:
- Replacement *of* a filter with this flag never clears the flag but
does change steering and saved priority
- Replacement *by* a filter with this flag only sets the flag but does
not change steering
- Removal with priority < EFX_FILTER_PRI_REQUIRED really resets RX
steering and saved priority
This could support precise MAC filtering on Siena in future.
As a side-benefit, the default MAC filters are hidden from ethtool
until they are steered.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Move the special case for removal of default filters from
efx_farch_filter_table_clear_entry() into a wrapper function,
efx_farch_filter_table_remove(). Move the existence and priority
checks into the latter and use it where appropriate.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Aside from accelerated RFS, there is almost nothing that can be shared
between the filter table implementations for the Falcon architecture
and EF10.
Move the few shared functions into efx.c and rx.c and the rest into
farch.c. Introduce efx_nic_type operations for the implementation and
inline wrapper functions that call these.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Currently every call to efx_farch_filter_table_clear_entry() is
shortly followed by a conditional reset of the table limits. The new
limits (0) are not pushed to hardware until the next filter insertion.
Move both the reset and the hardware reconfiguration into
efx_farch_filter_table_clear_entry(), and add an explanatory comment.
Also, make consistent use of the term 'search limit' for the maximum
number of probes the NIC must make when searching for a filter of a
particular type.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Move the common state from struct efx_filter_state into struct efx_nic.
Rename struct efx_filter_state to efx_farch_filter_state and change
the type of efx_nic::filter_state to void *.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Replace type field with match_flags. Add rss_context and match values
covering of most of what is now in the MCDI protocol.
Change some fields into bitfields so that the structure size doesn't grow
beyond 64 bytes.
Ditch the filter decoding functions as it is now easier to pick apart
the abstract structure.
Rewrite ethtool NFC rule functions to set/get filter match flags and
values directly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The filter table(s) on EF10 are managed by firmware and will need
almost entirely separate code. Rename the types and functions used
within the existing implementation. The current definition of struct
efx_filter_spec is really implementation-specific, so we need to keep
it. For now, define a separate structure for the internal
representation but leave them identical.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The PLL hang workaround is required only for AR9330 and
AR9340. This issue was first observed on an AP121 and the WAR
is enabled for AR9340 also (DB120 etc.), since it uses a PLL
design identical to AR9330. This is not required for AR9485 and AR9550.
Various bugs have been reported regarding this:
https://bugzilla.redhat.com/show_bug.cgi?id=997217https://bugzilla.redhat.com/show_bug.cgi?id=994648
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_htc adds padding between the 802.11 header and the payload during
TX by moving the header. When handing the frame back to mac80211 for TX
status handling the header is not moved back into its original position.
This can result in a too small skb headroom when entering ath9k_htc
again (due to a soft retransmission for example) causing an
skb_under_panic oops.
Fix this by moving the 802.11 header back into its original position
before returning the frame to mac80211 as other drivers like rt2x00
or ath5k do.
Reported-by: Marc Kleine-Budde <mkl@blackshift.org>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Tested-by: Marc Kleine-Budde <mkl@blackshift.org>
Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gotta love a macro that doesn't reduce the typing you have to do.
Also, only the driver core, and one network driver uses this. The
driver core functions will be going away soon, and I'll convert the
network driver soon to not need this as well, so delete it for now
before anyone else gets some bright ideas and wants to use it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
My current 3.11 fix:
commit 788f7a56fc
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Thu Aug 1 12:07:55 2013 +0200
iwl4965: reset firmware after rfkill off
broke rfkill notification to user-space . I missed that bug, because
I compiled without CONFIG_RFKILL, sorry about that.
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WARNING:JIFFIES_COMPARISON: Comparing jiffies is almost always wrong;
prefer time_after, time_before and friends
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While doing shutdown on the PCI device, the corresponding callback
function e1000e_shutdown() is trying to clear those correctable
errors on the upstream P2P bridge. Unfortunately, we don't have
the upstream P2P bridge under some cases (e.g. PCI-passthrou for
KVM on Power). That leads to kernel crash eventually.
The patch adds one more check on that to avoid kernel crash.
Signed-off-by: Li Zhang <zhlcindy@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch attempts to work around a problem found with some systems where
the call to pci_diable_link_state_locked() fails. As a result, ASPM is not,
in fact, disabled. Changing disable ASPM code to check if state actually
is disabled after the call and, if not, try another way to disable it.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Acked-by: Bruce W. Allan <bruce.w.allan@intel.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit (c96ddb0b e1000e: Use marco instead of digit for defining
e1000_rx_desc_packet_split) moved a define from one file to another but
missed using proper indentation/whitespace.
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the ethtool callbacks necessary to change the RETA
indirection table from userspace.
In order to achieve this, we add the indirection table field (rss_indir_tbl)
in the board specific data structure (struct igb_adapter) to preserve the
values across hardware resets.
The indirection table must be initialized with default values in the
following cases:
* at module init time
* when the number of RX queues changes.
For this reason we add a new field (rss_indir_tbl_init) in igb_adapter
that keeps track of the number of RX queues. Whenever the number of RX
queues changes, the rss_indir_tbl is modified and initialized with default
values. The rss_indir_tbl_init is updated accordingly.
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Laura Mihaela Vasilescu <laura.vasilescu@rosedu.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
RETA indirection table is used to assign the received data to a CPU
in order to maintain an efficient distribution of network receive
processing across multiple CPUs.
This patch removes the hard-coded value for the size of the indirection
table and defines a new macro.
Signed-off-by: Laura Mihaela Vasilescu <laura.vasilescu@rosedu.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes issues found with older parts and older NVM tools in the
display of the version in ethtool.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the specific device id support for versions of i210 that do
not have flash installed.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch refactors NVM read functions in order to accommodate i210 devices
that do not have a flash. Previously, this was not supported on i210
devices.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch refactors the init_nvm_params functions for 82575 and adds a new
function for the i210/i211 devices in order to configure separately the NVM
functionality for the i210/i211 family.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we limit the lower bound for max_frame_size to
the size of a standard Ethernet frame. This allows for feature parity with
other Intel based drivers such as ixgbe.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
MSI-X interrupts are required for SR-IOV operation. Check to make sure
they're enabled before allowing the user to turn on VFs.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds rcu_lock to avoid possible race condition with igb_update_stats
function accessing the rings in free_ q_vector.
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes register read to "just-read" without returning a value
for hardware to accurately latch the register value.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch resets the link, if link is up - whenever users enable or disable EEE
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_set_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_set_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a type cast from 'unsigned int' to 'int'.
'priv->instance' may less than zero, so need a type cast, the related
warnings (allmodconfig, "EXTRA_CFLAGS=-W"):
drivers/net/can/c_can/c_can_platform.c:198:3: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_set_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using deva_set_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Sergei Shtylyov explained in the #mipslinux IRC channel:
[Mon 2013-08-19 12:28:21 PM PDT] <headless> guys, are you sure it's not "DMA off stack" case?
[Mon 2013-08-19 12:28:35 PM PDT] <headless> it's a known stack corruptor on non-coherent arches
[Mon 2013-08-19 12:31:48 PM PDT] <DonkeyHotei> headless: for usb/ehci?
[Mon 2013-08-19 12:34:11 PM PDT] <DonkeyHotei> headless: explain
[Mon 2013-08-19 12:35:38 PM PDT] <headless> usb_control_msg() (or other such func) should not use buffer on stack. DMA from/to stack is prohibited
[Mon 2013-08-19 12:35:58 PM PDT] <headless> and EHCI uses DMA on control xfers (as well as all the others)
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to get an interface specification if we know it's the
wrong one.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
this pull-request for net-next consists of a series by Alexander
Shiyan, he cleans up the mcp251x driver. As the first patch touches
arch/arm/mach-pxa, it's acked by Haojian Zhuang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the no_csum_insertion private parameter that is not used anymore
and, also, the "likely" annotation from the condition that is not in a critical path.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Acked-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only thing we may have from tun device is the fprog, whic contains
the number of filter elements and a pointer to (user-space) memory
where the elements are. The program itself may not be available if the
device is persistent and detached.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a small problem with sk-filters on tun devices. Consider
an application doing this sequence of steps:
fd = open("/dev/net/tun");
ioctl(fd, TUNSETIFF, { .ifr_name = "tun0" });
ioctl(fd, TUNATTACHFILTER, &my_filter);
ioctl(fd, TUNSETPERSIST, 1);
close(fd);
At that point the tun0 will remain in the system and will keep in
mind that there should be a socket filter at address '&my_filter'.
If after that we do
fd = open("/dev/net/tun");
ioctl(fd, TUNSETIFF, { .ifr_name = "tun0" });
we most likely receive the -EFAULT error, since tun_attach() would
try to connect the filter back. But (!) if we provide a filter at
address &my_filter, then tun0 will be created and the "new" filter
would be attached, but application may not know about that.
This may create certain problems to anyone using tun-s, but it's
critical problem for c/r -- if we meet a persistent tun device
with a filter in mind, we will not be able to attach to it to dump
its state (flags, owner, address, vnethdr size, etc.).
The proposal is to allow to attach to tun device (with TUNSETIFF)
w/o attaching the filter to the tun-file's socket. After this
attach app may e.g clean the device by dropping the filter, it
doesn't want to have one, or (in case of c/r) get information
about the device with tun ioctls.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiqueue tun devices allow to attach and detach from its queues
while keeping the interface itself set on file.
Knowing this is critical for the checkpoint part of criu project.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tun devices cannot be created with ifidex user wants, but it's
required by checkpoint-restore project.
Long time ago such ability was implemented for rtnl_ops-based
interface for creating links (9c7dafbf net: Allow to create links
with given ifindex), but the only API for creating and managing
tuntap devices is ioctl-based and is evolving with adding new ones
(cde8b15f tuntap: add ioctl to attach or detach a file form tuntap
device).
Following that trend, here's how a new ioctl that sets the ifindex
for device, that _will_ be created by TUNSETIFF ioctl looks like.
So those who want a tuntap device with the ifindex N, should open
the tun device, call ioctl(fd, TUNSETIFINDEX, &N), then call TUNSETIFF.
If the index N is busy, then the register_netdev will find this out
and the ioctl would be failed with -EBUSY.
If setifindex is not called, then it will be generated as before.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The workarounds that currently use EFX_WORKAROUND_ALWAYS are in
Falcon-specific or Falcon-arch-specific code, so get rid of the
conditions altogether. Add/move comments as appropriate.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
EF10 functions don't have a fixed BAR size, and the minimum is not
large enough for all the queues we might want to allocate. We have to
find out the BAR size at run-time, and therefore phys_addr_channels
and mem_map_size cannot be defined per-NIC-type.
Change efx_nic_type::mem_map_size to a function pointer which is
called to find the wanted memory map size (before probe).
Replace efx_nic_type::phys_addr_channels with efx_nic::max_channels,
to be initialised by the probe function.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
When we poll for MCDI request completion, we don't hold the interface
lock while setting the response fields in struct efx_mcdi_iface.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
MCDI v2 adds a second header dword with wider command and length
fields. It also defines extra error codes.
Change the fallback error number for unknown MCDI error codes from EIO
to EPROTO. EIO is treated as indicating the MCDI transport has failed
and we need to reset the function, which is rather drastic.
v2 error codes and lengths don't fit into completion events, so for a
v2-capable transport, always read the response header rather then
using the event fields.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
EF10 controllers do not have shared memory for communication with the
MC; instead it reads requests and writes responses in host memory,
which allows for longer messages. It is also responsible for all
datapath control operations and hardware resource allocation, which
requires a large number of new commands and adds more possible error
cases. MCDI v2 extends the message header to support this.
Update the MCDI protocol definition header to include v2 lengths,
errors and messages, and a few definitions specific to the
SFC9100 family (codenames Farmingdale and Huntington) which is
the first generation of EF10.
Some messages have been extended, so adjust the code accordingly:
- The request for MC_CMD_DRV_ATTACH now includes a datapath firmware
ID. This is ignored by Siena but we should fill it in anyway,
initially always specifying low-latency datapath.
- The response for MC_CMD_GET_LOOPBACK_MODES now includes a 40G
field. Accept shorter responses that don't include it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Currently we only translate error codes in efx_mcdi_poll(), but we
also need to do so in efx_mcdi_ev_cpl().
The reason we didn't notice before is that the MC firmware error codes
are mostly taken from Unix/Linux and no translation is necessary on
most architectures. Make sure we notice any future failure by
changing the sign of resprc (matching the kernel convention) and BUG
if it's ever positive at command completion.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Result of skb_frag_dma_map() and dma_map_single() wasn't checked.
Added a check and proper handling in case of failure.
Moved the mapping to the beginning of mlx4_en_xmit(), before updating
the ring data structure to make error handling easier.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hardware gets into error state, must notify user about it.
When QP in error state no traffic will be tx'ed from the attached
tx_ring.
Driver should know how to recover from this unexpected state. I will send later
on the recovery flow, but having the print shouldn't be delayed.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug when FC and PFC are enabled/disabled at the same time.
According to ConnectX-3 Programmer Manual these two features are mutial
exclusive. So make sure when enabling PFC to turn off global FC and
vise versa. Otherwise it hurts the performance.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add efx_nic_type operations for the many efx_nic functions that need
to be implemented different on EF10. For now, change most of the
existing efx_nic_*() functions into inline wrappers. As a later step,
we may be able to improve branch prediction for operations used on the
fast path by copying the pointers into each queue/channel structure.
Move the Falcon/Siena implementations to new file farch.c and rename
the functions and static data to use a prefix of 'efx_farch_'.
Move efx_may_push_tx_desc() to nic.h, as the EF10 TX code will also
use it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Each function driver instance uses the MAC address of the
lowest function belonging to that physical port as a unique
port identifier. This port identifier is read and cached in
driver during probe and provided to user space through
ndo_get_phys_port_id()
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Enable diagnostic test via ethtool and QConvergeConsole
application when Multiple Tx queues are enabled on 82xx
series adapters.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o using ethtool {set|get}_channel option, user can change number
of Tx queues for 82xx Series adapter.
o updated ethtool -S <ethX> option to display stats from each Tx queue.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o 82xx firmware allows support for multiple Tx queues. This
patch will enable multi Tx queue support for 82xx series
adapter. Max number of Tx queues supported will be 8.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently efx_stop_datapath() will try to flush our DMA queues (if DMA
is enabled), then finalise software and hardware state for each queue.
However, for EF10 we must ask the MC to finalise each queue, which
implicitly starts flushing it, and then wait for the flush events.
We therefore need to delegate more of this to the NIC type.
Combine all the hardware operations into a new NIC-type operation
efx_nic_type::fini_dmaq, and call this before tearing down the
software state and buffers for all the DMA queues.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
efx_unregister_netdev() should not call efx_release_tx_buffers()
directly, as it is already done when closing the device:
efx_net_stop() -> efx_stop_all() -> efx_stop_datapath() ->
efx_fini_tx_queue() -> efx_release_tx_buffers().
(This was presumably a workaround for a race between efx_stop_all()
and the data path that has since been properly fixed.)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
rx_queue::enabled guards refill, so rename it to reflect that. Clear
it at the start of the queue teardown process rather than waiting for
the RX queue to be flushed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We unconditionally acknowledge legacy interrupts just before disabling
them. This workaround is needed on Falcon A1 but probably not on
later chips where the legacy interrupt mechanism is different. It was
also originally done after the IRQ handler was removed, not before.
Restore the original behaviour for Falcon A1 only by doing this
acknowledgement in the efx_nic_type::fini operation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
There are many problems with the current efx_stop_interrupts() and
efx_start_interrupts():
1. On Siena, it is unsafe to disable the master IRQ enable bit
(DRV_INT_EN_KER) while any IRQ sources are enabled.
2. On EF10 there is no master IRQ enable bit, so we cannot expect to
defer IRQs without tearing down event queues. (Though I don't think
we will need to keep any event queues around while the device is down,
as we do for VFDI on Siena.)
3. synchronize_irq() only waits for a running IRQ handler to finish,
not for any propagation through IRQ controllers. Therefore an IRQ may
still be received and handled after efx_stop_interrupts() returns.
IRQ handlers can then race with channel reallocation.
To fix this:
a. Introduce a software IRQ enable flag. So long as this is clear,
IRQ handlers will only acknowledge IRQs and not touch the channel
structures.
b. Define a new struct efx_msi_context as the context for MSIs. This
is never reallocated and is sufficient to find the software enable
flag and the channel structure. It also includes the channel/IRQ
name, which was previously separated out as it must also not be
reallocated.
c. Split efx_{start,stop}_interrupts() into
efx_{,soft_}_{enable,disable}_interrupts(). The 'soft' functions
don't touch the hardware master enable flag (if it exists) and don't
reinitialise or tear down channels with the keep_eventq flag set.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
efx_process_channel_now() is unneeded since self-tests can rely on
normal NAPI polling. Remove it and all calls to it.
efx_channel::work_pending and efx_channel_processed() are also
unneeded (the latter being the same as efx_nic_eventq_read_ack()).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The EF10 architecture has a very different register layout from
previous controllers, so we'll use separate files for the two sets of
register definitions. Use 'farch' as an abbreviation for
Falcon-architecture.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
On EF10, the firmware is in charge of allocating buffer table entries.
Change struct efx_special_buffer to use a struct efx_buffer member,
so that it can be used with efx_nic_{alloc,free}_buffer() in that
case.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Most call sites for efx_nic_alloc_buffer() are part of the probe or
reconfiguration paths and can allocate with GFP_KERNEL. A few others
should use GFP_NOIO (I think). Only one is in atomic context and
must use the current GFP_ATOMIC.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Move the lowest layer (transport) of the current MCDI code to
per-NIC-type operations.
Introduce a new structure and efx_nic member for MCDI-specific data.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
This should probably be done during MCDI initialisation for any NIC.
Change efx_mcdi_init() to return an error code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Collect together MCDI port functions from mcdi.c, mcdi_mac.c,
mcdi_phy.c and siena.c. Rename the 'siena' functions accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We currently require that MCDI request and response lengths are
multiples of 4 bytes, because we will copy dwords in and out of shared
memory and we want to be sure we won't read or write out of bounds.
But all we really need to know is that there is sufficient padding for
that. Also, we should ensure that buffers are dword-aligned, as on
some architectures misaligned access will result in data corruption or
a crash.
Change the buffer type to array-of-efx_dword_t and remove the
requirement that the lengths are multiples of 4.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
A few functions are using heap buffers; change them to use stack
buffers as we really don't need to resort to the heap for a 252
byte buffer in process context.
MC_CMD_MEMCPY is quite weird in that it can use inline data placed in
the request buffer after the array of records. Thus there are two
variable-length arrays and we can't use the normal accessors for
the second. So we have to use _MCDI_PTR() in efx_sriov_memcpy().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We need to access arrays of 16-bit words and 32-bit dwords in MCDI
buffers based on the MCDI protocol definitions.
We should also be able to read and write fields within structures,
without specifying an array index each time. So add MCDI_FIELD()
and make MCDI_ARRAY_FIELD() use it. Also add MCDI_SET_FIELD().
Split MCDI_ARRAY_PTR() into MCDI_ARRAY_STRUCT_PTR() and
_MCDI_ARRAY_PTR(), which are currently identical but will diverge in
later changes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Add _MCDI_DWORD() which yields an lvalue for the given dword field
and change MCDI_DWORD(), MCDI_SET_DWORD() and MCDI_QWORD() to use it.
Fold the rather trivial MCDI_PTR2() into MCDI_PTR() and _MCDI_DWORD().
Remove MCDI_SET_DWORD2() and MCDI_QWORD2(). MCDI_DWORD2() should also
go, but it still has one user which we'll get rid of later.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
MCDI_DECLARE_BUF declares a variable as an MCDI buffer of the
requested length, adding any necessary padding.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
commit 385904f819 ('sfc: Don't use
efx_filter_{build,hash,increment}() for default MAC filters') used the
wrong name to find the index of default RX MAC filters at insertion/
update time. This could result in memory corruption and would in any
case silently fail to update the filter.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
brcm80211 cannot handle sending frames with CCK rates as part of an
A-MPDU session. Other drivers may have issues too. Set the flag in all
drivers that have been tested with CCK rates.
This fixes a reported brcmsmac regression introduced in
commit ef47a5e4f1aaf1d0e2e6875e34b2c9595897bef6
"mac80211/minstrel_ht: fix cck rate sampling"
Cc: stable@vger.kernel.org # 3.10
Reported-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Patch allow to use different mode settings for SPI (MODE3 for example)
and limit maximal speed according to IC datasheet.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Flags is not used by boards, so remove this field from the driver
platform_data.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch replaces power callbacks to the regulator API. To improve
the readability of the code, helper for the regulator enable/disable
was added.
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some boards require custom PHY configuration, for example due to trace
length differences. Add the ability to configure these registers in
order to get the PHY to function on boards that need it.
Because PHYs are auto-detected based on MDIO device IDs, allow PHY
configuration to be specified in the parent Ethernet device node if no
PHY device node is present.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some phy's can be configured to enable wake on lan (e.g. at803x or marvell 88E1318S).
There is no way how to enable wol on CPSW with such connected phys. This patch
adds this support. It is provided by calling the phy's related code.
Tested on board with at8030x connected phy. Wol interrupt line is
connected to GPIO0 on am335x.
Signed-off-by: Matus Ujhelyi <ujhelyi.m@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW driver no longer supports platform register as all the SoCs which has CPSW
are supporting DT only booting, so moving cpsw.h header file from platform
include to drivers/net/ethernet/ti
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_ioremap_resource instead of devm_request_and_ioremap.
This was done using the semantic patch
scripts/coccinelle/api/devm_ioremap_resource.cocci
The relevant call to platform_get_resource was manually moved down to the
call to devm_ioremap_resource.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Regarding the iwlwifi bits, Johannes says:
"We revert an rfkill bugfix that unfortunately caused more bugs, shuffle
some code to avoid touching the PCIe device before it's enabled and
disconnect if firmware fails to do our bidding. I also have Stanislaw's
fix to not crash in some channel switch scenarios."
As for the mac80211 bits, Johannes says:
"This time, I have one fix from Dan Carpenter for users of
nl80211hdr_put(), and one fix from myself fixing a regression with the
libertas driver."
Along with the above...
Dan Carpenter fixes some incorrectly placed "address of" operators
in hostap that caused copying of junk data.
Jussi Kivilinna corrects zd1201 to use an allocated buffer rather
than the stack for a URB operation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of_dev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Acked-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &ofdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to fix a problem in the rtl8211 where the driver
wasn't properly enabled the interrupt on link change status.
it has to enable the ineterrupt on the bit 10 in the register 18
(INER).
Reported-by: Sharma Bhupesh <B45370@freescale.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the 'register_type' field of the 'sh_eth' driver's platform data is not
used by the driver anymore, it's time to remove it and its initializers from
the SH platform code. Also move *enum* declaring values for this field from
<linux/sh_eth.h> to the local driver's header file as they're only needed
by the driver itself now...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register layout is a SoC characteristic, so it's wrong that it's stored
in the otherwise board specific platform data. Add 'register_type' field to
'struct sh_eth_cpu_data', initialize it properly for each SoC, and read it
from this structure instead of the platfrom data from now on...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not clear Broadcast/Multicast/Unicast Wake Flag or LanWake in
Config5. This is necessary to preserve WOL state when the driver is
loaded. Although the r8168 vendor driver does not write Config5 (it has
been commented out), Hayes Wang from Realtek said that masking bits like
this is more sensible.
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ndo_busy_poll handler. Use skb_mark_napi_id to mark receive
packets with the napi id. For each slice, use per-slice spinlock and
state variable to ensure that only one handler processes receive
pacekts.
Locking, statistics counters, and the ndo_busy_poll handler follow
those in the ixgbe driver. So, credit goes to that driver's authors.
Signed-off-by: Hyong-Youb Kim <hykim@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When attempting to change e.g. the advertising mask when the link is down
ecmd->speed is -1 causing mii_ethtool_sset() to bail out.
This bug bit when connecting to a gigabit switch through a 4-pin (industrial)
cable, since link negotiation would not complete (both endpoints claimed to
be gigabit-capable, but this is not possible with only 4 pins).
Any attempt to fix this by setting autonegation to not offer 1000Mbps
failed as the setting would not be accepted while the link was still down...
Set ecmd->speed to SPEED_1000 to satisfy mii_ethtool_sset()
(the actual value of ecmd->speed doesn't matter as long as it is valid,
since a re-negotation is forced afterwards).
Signed-off-by: Anders Larsen <al@alarsen.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing unlock before return from function moxart_mac_start_xmit()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool core will lower the requested length to the one returned by
get_regs_len, therefore no additional check is needed in the get_regs
function.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch generates a hardware crash notification (NETDEV_REBOOT)
during reset. After a hardware crash, ENIC resets all its resources
including queue pair filters programmed by USNIC. USNIC registers for
this notification, and on receiving it, reprograms the queue pair
filters.
Signed-off-by: Neel Patel <neepatel@cisco.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an interface for USNIC to proxy firmware commands
through ENIC.
Signed-off-by: Neel Patel <neepatel@cisco.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch,
- Adds new firmware commands for the new Cisco Low Latency NIC
(aka. USNIC).
Signed-off-by: Neel Patel <neepatel@cisco.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If via_ircc_open() fails, data structures of the driver left uninitialized,
but probe (via_init_one()) returns zero. That can lead to null pointer dereference
in via_remove_one(), since it does not check drvdata for NULL.
The patch implements proper error code propagation.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the user turns off VNET_HDR support on the
macvtap device, there is no way to provide any
offload information to the user. So, it's safer
to ignore offload setting then depend on the user
setting them correctly.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the user turns off IFF_VNET_HDR flag, attempts to change
offload features via TUNSETOFFLOAD do not work. This could cause
GSO packets to be delivered to the user when the user is
not prepared to handle them.
To solve, allow processing of TUNSETOFFLOAD when IFF_VNET_HDR is
disabled.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In macvtap, tap_features specific the features of that the user
has specified via ioctl(). If we treat macvtap as a macvlan+tap
then we could all the tap a pseudo-device and give it other features
like SG and GSO. Then we can stop using the features of lower
device (macvlan) when forwarding the traffic the tap.
This solves the issue of possible checksum offload mismatch between
tap feature and macvlan features.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't emit OOM warnings when k.alloc calls fail when
there there is a v.alloc immediately afterwards.
Converted a kmalloc/vmalloc with memset to kzalloc/vzalloc.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
o Use appropriate firmware image file name based on device IDs.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Loopback initiator function drivers should process loopback time extend AEN.
These AENs are triggered by the loopback time extend mailbox command
issued by the target function drivers.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o 84xx adapters support VLAN stripping for PVID. Packets don't have
VLAN tag inserted in case of PVID. So packet should follow non vlan path.
o Use capability bit to set PVID mode.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are possible HW configurations in which PFs will have SR-IOV capability
but will have Max VFs set to 0 - this happens when there are Multi-Function
devices where the VFs are allocated to only some of the PFs.
DMAE is configured to support VFs only if the configuring PF has supported VFs.
In case the first PF to be loaded will be one without supported VFs, it will
not configure DMAE to the VF-supporting mode. When VFs of other PFs will be
loaded later on, they will not be able to communicate with their PF.
This changes the requirement for configuring DMAE for VF-supporting mode;
If the device has SR-IOV capabilities there must be some PF that has
max supported VFs > 0, thus it will configure the DMAE for supporting VFs.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since SR-IOV can be activated dynamically and iproute2 can be called
asynchronously, the various callbacks need a robust sanity check before
attempting to access the SR-IOV database and members since there are numerous
states in which it can find the driver (e.g., PF is down, sriov was not enabled
yet, VF is down, etc.).
In many of the states the callback result will be null pointer dereference.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During probe, VFs might erroneously try to access the shared memory (which
only PFs are capabale of accessing), causing benign attentions to appear.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When publishing information via getfeatcfg(), bnx2x driver didn't consider
remote errors (e.g., switch that doesn't support DCBX) when setting the
error flags.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After notification that DCBX configuration has ended arrived to the driver,
the driver configured the FW/HW in sleepless context.
As a result, it was possible to reach a race (mostly with CNIC registration)
in which the configuration will return a timeout, failing to set the DCBX
results correctly.
This patch moves the configuration following the DCBX end into the slowpath
RTNL task (i.e., sleepless context protected by the RTNL lock), allowing the
configuration to cope with such races.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 3deb816 "bnx2x: Add a periodic task for link PHY events"
link state changes can be detected not only via the attention flow but also
from the periodic task.
If the link state will change in such a manner (i.e., via the periodic task),
dropless flow-control will not be configured.
This patch remedies the issue, adding the missing configuration to all required
flows.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch allows transmit side vlan offload for vxlan
devices.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than having static headroom calculation, adjust headroom
according to target device.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch allows more code sharing between vxlan and ovs-vxlan.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch adds data field to vxlan socket and export
vxlan handler api.
vh->data is required to store private data per vxlan handler.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once we have ovs-vxlan functionality, one UDP port can be assigned
to kernel-vxlan or ovs-vxlan port. Therefore following patch adds
vxlan demux functionality, so that vxlan or ovs module can
register for particular port.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use iptunnel_pull_header() for better code sharing.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restructure vxlan-socket management APIs so that it can be
shared between vxlan and ovs modules.
This patch does not change any functionality.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
v6-v7:
- get rid of zero refcnt vs from hashtable.
Signed-off-by: David S. Miller <davem@davemloft.net>
Split some parts of code into another function to simplify
tx_bottom(). Use while loop to replace the goto loop.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move some declearation of variables in rx_bottom().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use r8152_get_tx_agg for getting tx agg list
- Replace submit rx with goto submit
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the type of contex of tx_agg and rx_agg from void * to
staruc r8152 *.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 2011_1007_RT5390_RT5392_Linux_STA_V2.5.0.3_DPO
driver enables PCIe wakeup for these chips as well.
Do the same in rt2x00.
References:
rt28xx_init in common/rtmp_init_intf.c
RTMPInitPCIeLinkCtrlValue in os/linux/rt_rbus_pci_drv.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2800pci driver uses the same [RT]XWI size
for all chipsets, however some chips requires
different values.
The size of the [RT]XWI structures is a constant
value for a given chipset and it does not depend
on the underlying interface. Add a helper function
which returns the correct values for the actual
chipset and use the new helper both in the rt2800usb
and in the rt2800pci drivers. This ensures that both
drivers are using the correct values.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CSA is only enabled for one interface, but the same limitation applies
for mac80211 too. It checks whether the beacon has been sent (different
approaches for non-EDMA-enabled and EDMA-enabled devices), and completes
the channel switch after that.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To enable support for 5/10 MHz, some internal functions must be
converted from using the (old) channel_type to chandef. This is a good
chance to change all remaining occurences.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
5/10 MHz channels should always use SIFS times as defined in IEEE
802.11-2012 18.4.4 (OFDM PHY characteristics). This makes it compatible
to ath5k, which does the same.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Performance Based Window snooze mechanism is based on uAPSD and is
used in low-medium traffic scenarios, in order to provide better power
performance while insuring low latency and jitter for the incoming traffic.
This patch enables PBW snoozing in case uAPSD is enabled and all ACs are
uAPSD trigger and delivery enabled.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use beacon statistics notification to track RSSI.
Notify mac80211 when the tresholds are crossed.
The roaming treshold is configured to be
equal to cqm_thold. If the beacon filtering command
is not supported by fw fall back and use mac80211
mechanism.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The callers of iwl_drv_start() are probe functions. If a probe
function returns 0, it means it succeeded. So if NULL was returned by
iwl_drv_start(), it would be considered as a success.
Fix this by returning -ENOMEM if the driver struct allocation fails in
iwl_drv_start().
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix the help texts to properly reflect the 7260 and 3160 devices
support.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of assigning the default max probe length to 200 in the main
code, create a macro for consistency and clarity.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To be able to add more logic to the resume code, refactor it a bit,
moving some status checking/reporting logic into a new function.
The locking becomes a bit odd (one of the new functions now unlocks
the mutex) but this will be required to call new mac80211 APIs in
there later.
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the previous QUERY_PAGES command version we used one command to get the
required amount of boot, init and post init pages. The new version uses the
op_mod field to specify whether the query is for the required amount of boot,
init or post init pages. In addition the output field size for the required
amount of pages increased from 16 to 32 bits.
In MANAGE_PAGES command the input_num_entries and output_num_entries fields
sizes changed from 16 to 32 bits and the PAS tables offset changed to 0x10.
In the pages request event the num_pages field also changed to 32 bits.
In the HCA-capabilities-layout the size and location of max_qp_mcg field has
been changed to support 24 bits.
This patch isn't compatible with firmware versions < 5; however, it turns out that the
first GA firmware we will publish will not support previous versions so this should be OK.
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent fix d9bf5f1309 "tun: compare with 0 instead of total_len" is
not totally correct. Because "len" and "sizeof()" are size_t type, that
means they are never less than zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Load firmware from file before setting up interrupts.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver was hitting a panic at the time of adapter reset due to invalid command
access from the list which had been already freed by the queuing thread.
Flush all the pending commands from the list before proceeding with adapter reset
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o After firmware reset VFs were failing to come up because of not
reinitializing mailbox data structures. Reinitialize them so that
VFs can come up after firmware reset.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Do not allow interrupt test when adapter is resetting.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver was misinterpreting the return status for beacon
state query leading to incorrect interpretation of beacon
state and logging an error message for successful status.
Fixed the driver to properly interpret the return status.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver was issuing set driver version command through all
functions in the adapter. Fix the driver to issue set driver
version once per adapter, through function 0.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d8af4dfd8 ("net/tg3: Fix kernel crash") introduced a possible
NULL pointer dereference in tg3 driver when !netdev || !netif_running(netdev)
condition is met and netdev is NULL. Then, the jump to the 'done' label
calls dev_close() with a netdevice that is NULL. Therefore, only call
dev_close() when we have a netdevice, but one that is not running.
[ Add the same checks in tg3_io_slot_reset() per Gavin Shan - by Nithin
Nayak Sujir ]
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Gavin Shan <shangw@linux.vnet.ibm.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding type casts to suppress sparse warnings:
* warning: cast to restricted __le32/__le16
Signed-off-by: Mark Schulte <schultetwin@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the rx_fifo queue is accessed only using the various
lockless SKB queue routines, there is no need to initialize
the lock and __skb_queue_head_init() can be used.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The documentation for antenna diversity says:
"The decision of diversity is done at 802.11 preamble. So, for
11G/11B, for every MAC packet hardware will do a decision. But in
11N with aggregation, the decision is made only at the preamble and
all other MPDUs will use the same LNA as the first MPDU."
Make use of rs_firstaggr to avoid needlessly scanning for LNA
changes.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The combined RSSI can be invalid which is indicated by
the value -128. Use RX_FLAG_NO_SIGNAL_VAL for such cases.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case a descriptor has the "done" bit clear and the
next descriptor has it set, we drop both of them. If
the packet that is received after these two packets
is dropped for some reason, "discard_next" will not cleared.
Fix this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MIC/PHYERR/CRC error bits are valid only for
the last desc. for chained packets. Check this early
in the preprocess() routine and bail out.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure that chained descriptors are handled correctly
before the packet is parsed to determine if it is a beacon.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handle chained descriptors and increment the RX counter
only for valid packets. Since this is used only by MCI,
use CONFIG_ATH9K_BTCOEX_SUPPORT.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The various error bits that ath_debug_stat_rx()
checks are valid only for the last descriptor for
a chained packet, handle this correctly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Parse the PHY error details only for the last fragment
in case descriptors are chained.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to calculate the mactime for chained
descriptor packets, so make sure that this is done
only for the last fragment of valid packets.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The keymiss events are valid only in the last descriptor
of a packet. Fix this by making sure that we return
early in case of chained descriptors.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Frames with invalid or zero length can be discarded
early, there is no need to check the crypto bits.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the DFS code appears to process the phy errors
ATH9K_PHYERR_RADAR and ATH9K_PHYERR_FALSE_RADAR_EXT,
check for the correct phyerr status in the main RX
tasklet routine.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If usb auto suspend is enabled or system run in to suspend/resume
cycle, ath9k-htc adapter will stop to response. It is reproducible on xhci HCs.
Host part of problem:
XHCI do timing calculation based on Transfer Type and bInterval,
immediately after device was detected. Ath9k-htc try to overwrite
this parameters on module probe and some changes in FW,
since we do not initiate usb reset from the driver this changes
are not took to account. So, before any kind of suspend or reset,
host controller will operate with old parameters. Only after suspend/resume
and if interface id stay unchanged, new parameters will by applied. Host
will send bulk data with no intervals (?), which will cause
overflow on FIFO of EP4.
Firmware part of problem:
By default, ath9k-htc adapters configured with EP3 and EP4
as interrupt endpoints. Current firmware will try to overwrite
ConfigDescriptor to make EP3 and EP4 bulk. FIFO for this endpoints
stay not reconfigured, so under the hood it is still Int EP.
This patch is revert of 4a0e8ecca4 commit which trying to
reduce CPU usage on some systems. Since it will produce more bug
as fixes, we will need to find other way to fix it.
here is comment from kernel source which has some more explanation:
* Some buggy high speed devices have bulk endpoints using
* maxpacket sizes other than 512. High speed HCDs may not
* be able to handle that particular bug, so let's warn...
in our case EP3 and EP4 have maxpacket sizes = 64!!!
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix for TCP iperf from Windows to Linux stall after about 1sec
Hardware reports false errors in some situations:
Microsoft IP stack, in violation of RFC 1624, set TCP checksum that should be 0x0
as 0xffff. hardware report Rx csum error. If HW csum absolutely trusted,
this frame can be never received, as re-transmitted one will have same csum problem.
In addition, it mess up block ack reorder buffer, as if packet dropped, it is not score boarded
there.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If that flag stays set for a buffer that already ran through the tx path
once, it might cause issues in tx completion processing. Better clear it
early to ensure that this does not happen
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_tid_drain is only called when a station entry is being removed, so
there is no point in still tracking BAW state. Remove some unnecessary
code and a bogus TODO comment related to this.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They are not implemented, and accessing them might trigger errors
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Writing to that file is unnecessary and quirky, the antenna API should
be used instead. Use debugfs_create_u8 to allow reading the values.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 uses debugfs_remove_recursive, so there's no need for the
driver to do an explicit cleanup of its sta debugfs entry.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also reduce the size of a few fields where possible
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to a race condition that exists in the tx path, the hardware
might re-read the 'next' pointer of a descriptor of the last completed
frame. This only affects non-EDMA (pre-AR93xx) devices.
To deal with this race, defer clearing and re-linking a completed rx
descriptor until the next one has been processed.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Host tx glomming require an extended hardware sdio bus header to store
information for dongle. Introduce a variable in struct brcmf_sdio to replace
macro SDPCM_HDRLEN
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Streamlining sdio bus specific header related code as preparation for host
tx glomming
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
remove align from brcmf_bus since it is only used by sdio bus layer internally
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Abstract brcmf_sdio_txpkt_prep and brcmf_sdio_txpkt_postp as a preparation
of chained tx packets for host side tx glomming.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement the .tdls_oper() callback and indicate TDLS support
in the wiphy flags.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not every IF event from the firmware needs to result in a
related interface, netdev or wdev, on the host. This is
indicated in the event message. Handle that flag and effectively
ignore the firmware event.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
FWS uses locking to protect its data while being called from
various entries. On bus_txdata the lock was kept resulting in
unnecessary long locking, but also creating possibility for
deadlock. This update changes the locking to release lock when
bus_txdata is called.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When fw signalling is disabled tx is sent immediately. Using
queues and worker thread allows usb to do synchronous autopm. This
patch makes fws use queues and worker thread even if signalling is
not supported by FW or not enabled.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature moves the responsibility of collecting all MPDUs in an
AMPDU session in the correct order from the firmware to the host
driver. This reduces buffer requirement on the firmware side.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With firmware-signalling the packet handed to the bus specific driver
layer should not be discarded with brcmf_txcomplete() in the failure
path. Instead only an error is returned and the caller decides what
to do with the packet.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware-signalling needs transmit to firmware to be atomic and
uses a spinlock with irq disabled. Therefor, brcmf_sdbrcm_txdata()
should not use spin_unlock_bh() as it would enable the interrupts.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers supporting NAPI should use a NAPI-specific function for receiving
packets. Hence netif_rx is changed to netif_receive_skb.
Furthermore netif_napi_del should be used in the probe and remove function
to clean up the NAPI resource information.
Thanks to Francois Romieu, David Shwatrz and Rami Rosen for their help on
this patch.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the interrupt transfer to replace polling link status.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the tx/rx aggregation which could contain one or more packets
for each bulk in/out. This could reduce the loading of the host
controller by sending less bulk transfer.
The rx packets in the bulk in buffer should be 8-byte aligned, and
the tx packets in the bulk out buffer should be 4-byte aligned.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit f83331bab1.
As the tests PPC64 (powernv platform) show, IOMMU pages are leaking
when transferring big amount of small packets (<=64 bytes),
"ping -f" and waiting for 15 seconds is the simplest way to confirm the bug.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Santosh Rastapur <santosh@chelsio.com>
Cc: Jay Fenlason <fenlason@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Divy Le ray <divy@chelsio.com>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for some versions of firmware to advertise capabilities that driver
is not ready to handle. This may lead to controller stall. Since the driver is
interested only in subset of flags, clearing the rest.
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we set "len = total_len" in the beginning of tun_get_user(),
so we should compare the new len with 0, instead of total_len,
or the if statement always returns false.
Signed-off-by: Weiping Pan <wpan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initially I improperly set a boundary for maximum number of input
packets to process on NAPI poll ("work") so it might be more than
expected amount ("weight").
This was really harmless but seeing WARN_ON_ONCE on every device boot is
not nice. So trivial fix ("<" instead of "<=") is here.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
There might be a crash as during shutdown flow CNIC might try
to access resources already freed by bnx2x.
Change bnx2x_close() into dev_close() in __bnx2x_remove (shutdown flow)
to guarantee CNIC is notified of the device's change of status.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTE write access error might occur in MF_ALLOWED mode when IOMMU
is active. The patch adds rmmod HSI indicating to MFW to stop
running queries which might trigger this failure.
Signed-off-by: Barak Witkowsky <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETS can be enabled as a result of DCB negotiation, then
fairness must be recalculated after each negotiation.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add locking to protect different statistics flows from
running simultaneously.
This in order to serialize statistics requests sent to FW,
otherwise two outstanding queries may cause FW assert.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
This is a batch of updates intended for 3.12. It is mostly driver
stuff, although Johannes Berg and Simon Wunderlich make a good
showing with mac80211 bits (particularly some work on 5/10 MHz
channel support).
The usual suspects are mostly represented. There are lots of updates
to iwlwifi, ath9k, ath10k, mwifiex, rt2x00, wil6210, as usual.
The bcma bus gets some love this time, as do cw1200, iwl4965, and a
few other bits here and there. I don't think there is much unusual
here, FWIW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The new IP version which is present in AM43xx SoC has a minor changes and the
offsets are same as the previous version, so adding new IP version support in
the driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eTSEC has Rx and Tx flow control capabilities that may be enabled
through MACCFG1[Rx_Flow, Tx_Flow] bits. These bits must not be set
however when eTSEC is operated in Half-Duplex mode. Unfortunately,
the driver currently sets these bits unconditionally.
This patch adds the proper handling of the PAUSE frame capability
register bits by implementing the ethtool -A interface. When pause
autoneg is enabled, the controller uses the phy's capability to
negotiate PAUSE frame settings with the link partner and reconfigures
its Rx_Flow and Tx_Flow settings to match the capabilities of the
link partner. If pause autoneg is off, the PAUSE frame generation
may be forced manually (ethtool -A). Flow control is disabled by
default now.
This implementation is inspired by the tg3 driver.
Signed-off-by: Lutz Jaenicke <ljaenicke@innominate.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pptp driver has lots of byte order warnings from sparse.
This was because the on-the-wire header is in network byte order (obviously)
but the definition did not reflect that.
Also, the address structure to user space actually put the call id
in host order. Rather than break ABI compatibility, just acknowledge
the existing design.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA sync should sync the whole receive buffer, not just
part of it. Fixes log messages dma_sync_check.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that the definition of ax88172a_info matches the declaration seen
by users and silence sparse warnings about symbols without declarations
in the global namespace by moving the declaration into the shared header
asix.h.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make functions that are only referenced from ops structures static, they
do not need to be in the global namespace and sparse complains about this.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recognize XRC QPs in the SR-IOV resource tracker based on transport
type. The previous check didn't match IB_QPT_XRC_INI and caused an
invalid calculation for required mtt pages.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In stmmac_init_rx_buffers():
* add missing handling of dma_map_single() error
* remove superfluous unlikely() optimization while at it
Add stmmac_free_rx_buffers() helper and use it in dma_free_rx_skbufs().
In init_dma_desc_rings():
* add missing handling of kmalloc_array() errors
* fix handling of dma_alloc_coherent() and stmmac_init_rx_buffers() errors
* make function return an error value on error and 0 on success
In stmmac_open():
* add handling of init_dma_desc_rings() return value
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New routine has been added to avoid duplication of code to wait for
pending PCI transactions to complete. This makes use of that routine.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Acked-by: David S. Miller <davem@davemloft.net>
The Compressed LIP region is used to hold a limited number of Local
IPv6 addresses. This region is primarily used to reduce the TCAM
space consumed for an IPv6 offloaded connection. A 128-bit LIP will
be reduced to 13-bit and stored in the TCAM if there is a match
between the IPv6 tuple's LIP and the one stored in the CLIP region.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add cxgb4_create_server6 and cxgb4_remove_server routines to create
and remove listening IPv6 servers.
Return success (0) from cxgb4_create_server in case of ctrl queue
congestion since in case of congestion, passive open request gets
queued and gets processed later. If a non-zero value were returned it
would be treated as an error and the ULD would free STID, which can
result in an error in passive open reply.
Add cpl structure for active open request with IPv6 address for T5.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch enables 'can_dma_sg' flag for ax88179_178a device
if the attached host controller supports building packet from
discontinuous buffers(DMA SG is possible), so TSO can be enabled
and skb fragment buffers can be passed to usb stack via urb->sg
directly.
With the patch, system CPU utilization decreased ~50% and throughput
increased by ~10% when doing iperf client test on one ARM A15 dual
core board.
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Grant Grundler <grundler@google.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Eric Dumazet <edumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces support of DMA SG if the USB host controller
which usbnet device is attached to is capable of building packet from
discontinuous buffers.
The patch supports passing the skb fragment buffers to usb stack directly
via urb->sg.
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Grant Grundler <grundler@google.com>
Cc: Freddy Xin <freddy@asix.com.tw>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
config: make ARCH=m68k allmodconfig
All error/warnings:
drivers/net/wireless/mwifiex/cfg80211.c: In function
'mwifiex_fill_coalesce_rule_info':
>> drivers/net/wireless/mwifiex/cfg80211.c:2493:3: error: implicit
declaration of function 'mwifiex_is_pattern_supported'
[-Werror=implicit-function-declaration]
drivers/net/wireless/mwifiex/cfg80211.c: At top level:
drivers/net/wireless/mwifiex/cfg80211.c:2537:12: warning:
'mwifiex_cfg80211_set_coalesce' defined but not used
[-Wunused-function]
cc1: some warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current and future chips supported by mvm will only have a maximum
of 2 antennas so all the MIMO3 related code and states can be dropped.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement basic uAPSD client support adding the following:
- Advertise uAPSD support in HW capabilities
- Set all ACs trigger- and delivery-enabled
- Set max SP length to 2 buffered frames
- Assign QNDP with the highest TID with no mandatory admission
control required
- Set uAPSD related parameters in Power Table command
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some more cleanups of unused fields and their initializations.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is a missing '-' character here so we return positive 'ENOMEM'
instead of negative. The caller doesn't care. All non-zero returns
are translated to '-ENOMEM' in iwl_pcie_nic_init().
This is just a cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This isn't very informative and can be deduced from rate_scale_table.
Remove as a preparation for dropping iwl_rs_rate_info.ieee.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The iwl_trans_pcie_alloc() function doesn't pass up error codes
returned from functions it calls, swallowing them and returning NULL
in all failure cases. The caller checks if the return value is NULL
and returns -ENOMEM. This is not correct, because in certain cases
the failure was not due to an OOM situation.
To fix this, modify the iwl_trans_pcie_alloc() function to use
ERR_PTR() to return error codes and clean up the error handling code
a bit.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The time event firmware API will change, add the support for that.
Use the new API throughout and convert to the old where needed.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the wdev from cfg80211 on to the driver as the vif
if given and it's valid for the driver.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To allow drivers to implement per-interface testmode operations
more easily, pass a wdev pointer if any identification for one
was given from userspace. Clean up the code a bit while at it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A lot of drivers check the frame protocol for ETH_P_PAE,
for various reasons (like making those more reliable).
Add a new flags bitmap to the TX control info and a new
flag indicating the control port protocol is in use to
let all drivers also apply such logic to other control
port protocols, should they be configured.
Also use the new flag in the iwlwifi drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix possibly wrong memcpy() bytes length since some CAN records received from
PCAN-USB could define a DLC field in range [9..15].
In that case, the real DLC value MUST be used to move forward the record pointer
but, only 8 bytes max. MUST be copied into the data field of the struct
can_frame object of the skb given to the network core.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit ac4e4af1e5 ("macvtap: Consistently use rcu functions"),
Thomas gets two different warnings :
BUG: using smp_processor_id() in preemptible [00000000] code: vhost-45891/45892
caller is macvtap_do_read+0x45c/0x600 [macvtap]
CPU: 1 PID: 45892 Comm: vhost-45891 Not tainted 3.11.0-bisecttest #13
Call Trace:
([<00000000001126ee>] show_trace+0x126/0x144)
[<00000000001127d2>] show_stack+0xc6/0xd4
[<000000000068bcec>] dump_stack+0x74/0xd8
[<0000000000481066>] debug_smp_processor_id+0xf6/0x114
[<000003ff802e9a18>] macvtap_do_read+0x45c/0x600 [macvtap]
[<000003ff802e9c1c>] macvtap_recvmsg+0x60/0x88 [macvtap]
[<000003ff80318c5e>] handle_rx+0x5b2/0x800 [vhost_net]
[<000003ff8028f77c>] vhost_worker+0x15c/0x1c4 [vhost]
[<000000000015f3ac>] kthread+0xd8/0xe4
[<00000000006934a6>] kernel_thread_starter+0x6/0xc
[<00000000006934a0>] kernel_thread_starter+0x0/0xc
And
BUG: using smp_processor_id() in preemptible [00000000] code: vhost-45897/45898
caller is macvlan_start_xmit+0x10a/0x1b4 [macvlan]
CPU: 1 PID: 45898 Comm: vhost-45897 Not tainted 3.11.0-bisecttest #16
Call Trace:
([<00000000001126ee>] show_trace+0x126/0x144)
[<00000000001127d2>] show_stack+0xc6/0xd4
[<000000000068bdb8>] dump_stack+0x74/0xd4
[<0000000000481132>] debug_smp_processor_id+0xf6/0x114
[<000003ff802b72ca>] macvlan_start_xmit+0x10a/0x1b4 [macvlan]
[<000003ff802ea69a>] macvtap_get_user+0x982/0xbc4 [macvtap]
[<000003ff802ea92a>] macvtap_sendmsg+0x4e/0x60 [macvtap]
[<000003ff8031947c>] handle_tx+0x494/0x5ec [vhost_net]
[<000003ff8028f77c>] vhost_worker+0x15c/0x1c4 [vhost]
[<000000000015f3ac>] kthread+0xd8/0xe4
[<000000000069356e>] kernel_thread_starter+0x6/0xc
[<0000000000693568>] kernel_thread_starter+0x0/0xc
2 locks held by vhost-45897/45898:
#0: (&vq->mutex){+.+.+.}, at: [<000003ff8031903c>] handle_tx+0x54/0x5ec [vhost_net]
#1: (rcu_read_lock){.+.+..}, at: [<000003ff802ea53c>] macvtap_get_user+0x824/0xbc4 [macvtap]
In the first case, macvtap_put_user() calls macvlan_count_rx()
in a preempt-able context, and this is not allowed.
In the second case, macvtap_get_user() calls
macvlan_start_xmit() with BH enabled, and this is not allowed.
Reported-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Bisected-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MOXA UC-711X hardware(s) has an ethernet controller that seem
to be developed internally. The IC used is "RTL8201CP".
Since there is no public documentation, this driver is mostly the
one published by MOXA that has been heavily cleaned up / ported
from linux 2.6.9.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding paged frags skbs to af_unix sockets introduced a performance
regression on large sends because of additional page allocations, even
if each skb could carry at least 100% more payload than before.
We can instruct sock_alloc_send_pskb() to attempt high order
allocations.
Most of the time, it does a single page allocation instead of 8.
I added an additional parameter to sock_alloc_send_pskb() to
let other users to opt-in for this new feature on followup patches.
Tested:
Before patch :
$ netperf -t STREAM_STREAM
STREAM STREAM TEST
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
2304 212992 212992 10.00 46861.15
After patch :
$ netperf -t STREAM_STREAM
STREAM STREAM TEST
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
2304 212992 212992 10.00 57981.11
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
callid_sock array is referenced via rcu_dereference and
sparse rcu checks complains about address space mismatch.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Nithin Nayak Sujir <nsujir@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Manish Chopra <manish.chopra@qlogic.com>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Andrew Gallatin <gallatin@myri.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: netdev@vger.kernel.org
Acked-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixed the condition of extend_desc for jumbo frame.
There is no check routine for extend_desc in the stmmac_jumbo_frm function.
Even though extend_desc is set if dma_tx is used instead of dma_etx.
It causes kernel panic.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LNA combining algorithm has to be run for cards
that support the required diversity features, make
sure that that correct conditions are met before
enabing this algorithm.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BTCOEX has to be *disabled* for WLAN RX diversity to
work on combo cards.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Create a per-vif dummy node entry for keeping the multicast software
queues. This helps in setups with a lot of mulitcast traffic that could
otherwise potentially drown out unicast traffic to stations.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of trying to schedule the same TID multiple times in a loop,
iterate over other TIDs/stations first.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a first step for improving fairness between legacy and 802.11n
traffic, and it should also improve reliability of resets and channel
changes by keeping the hardware queue depth very short.
When an aggregation session is torn down, all packets in the retry queue
will be removed from the BAW and freed.
For all subframes that have not been transmitted yet, the A-MPDU flag
will be cleared, and a sequence number allocated. This ensures that the
next A-MPDU session will get the correct initial sequence number.
This happens both on aggregation session start and stop.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise in some cases, EAPOL frames might be filtered during the
initial handshake, causing delays and assoc failures.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the tid aggregation state has been marked as inactive, free
completed tx packets immediately. When a new aggregation session has not
been initialized yet, the BAW checks do not recognize it as expired.
Might fix potential stalls in setting up a new aggregation session.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- Allow ath_tx_get_tid_subframe to return non-AMPDU subframes.
- Reset the tid paused state on aggregation stop
- Initialize software queues even when HT is not supported
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a packet has been tracked as part of the BlockAck window and added
to the hardware queue, it can end up back in the TID queue again with
fi->retries still set to 0 (e.g. if the frame was filtered). Keep an
extra bit for the BAW tracking status to fix this corner case.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The check for ATH_AMPDU_SUBFRAME_DEFAULT is unnecessary, since it's set
to half the maximum BlockAck Window size, which is already the maximum
value that h_baw could possibly have. Also remove unnecessary variables.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Improves packet retry order and helps with further tx queueing
improvements.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is essentially the same, but written shorter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00queue_pause_queue_nocheck()is used only in this file.
Fix the following sparse warning:
drivers/net/wireless/rt2x00/rt2x00queue.c:939:6: warning: symbol 'rt2x00queue_pause_queue_nocheck' was not declared. Should it be
static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure that CONFIG_ATH9K_BTCOEX_SUPPORT is used for
the WLAN/BT RX diversity hooks.
Reported by the kernel build testing backend.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Coalesce filters are configured in firmware based on settings
received from cfg80211.
Packet type which is required by firmware is determined based on
provided patterns in a rule:
Unicast: if pattern '01' with offset 0 is found
Multicast: if pattern '33:33' or '01:00:5e' with offset 0 is found
Broadcast: if pattern 'ff:ff:ff:ff' with offset 0 is found
Some example coalesce configuration files:
1) Coalesce Rx data packets from 192.168.0.88
mac address of our device is 00:50:43:21:53:7A
Source IP address offset comes out as 52 after following
calculations:
32 bytes of HW 802.11 header + 8 bytes LLC +
12 bytes in IPV4 header till source IP address
Destination mac is at offset 6 in HW header.
delay=100
condition=1
patterns=01,6+00:50:43:22,10+53:7A,52+c0:a8:00:58
2) Coalesce all broadcast and multicast packets(Multiple packet
types are not allowed in a single rule. Hence created separate
rules)
delay=400
condition=1
patterns=33:33
delay=400
condition=1
patterns=ff:ff:ff:ff
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The offset number is increased to accomodate requests from
user to match more fields in a Rx packet.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is modified so that it can be reused for coalesce feature.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Their names were generic. We need to define similar macros
for coalesce feature. Hence they are renamed here.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a regression introduced by:
commit fe5c3561e6
Author: stephen hemminger <stephen@networkplumber.org>
Date: Sat Jul 13 10:18:18 2013 -0700
vxlan: add necessary locking on device removal
The problem is that vxlan_dellink(), which is called with RTNL lock
held, tries to flush the workqueue synchronously, but apparently
igmp_join and igmp_leave work need to hold RTNL lock too, therefore we
have a soft lockup!
As suggested by Stephen, probably the flush_workqueue can just be
removed and let the normal refcounting work. The workqueue has a
reference to device and socket, therefore the cleanups should work
correctly.
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Tested-by: Cong Wang <amwang@redhat.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a regression introduced by:
commit 3fc2de2fab
Author: stephen hemminger <stephen@networkplumber.org>
Date: Thu Jul 18 08:40:15 2013 -0700
vxlan: fix igmp races
Before this commit, the old code was:
if (vxlan_group_used(vn, vxlan->default_dst.remote_ip))
ip_mc_join_group(sk, &mreq);
else
ip_mc_leave_group(sk, &mreq);
therefore we shoud check vxlan_group_used(), not its opposite,
for igmp_join.
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduced in cf3c4c0306
("8139cp: Add dma_mapping_error checking")
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want the data stored in "addr" and "qual", but the extra ampersands
mean we are copying stack data instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch fixes zd1201 not to use stack as URB transfer_buffer. URB buffers need
to be DMA-able, which stack is not.
Patch is only compile tested.
Cc: stable@vger.kernel.org
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having the same code sequentially, fall-through.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Simplify iwl_rxq_space to improve readability and reduce
the ambiguity spares to a single element.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reduce the ambiguity spares to a single element if the window size is not
smaller than the queue size. If smaller, no spares are required at all.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This debug level will be used in the future for logging
interaction with external modules.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code was only enabling it when already enabled, which
obviously can't work.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of bond_add_vlan() failure currently we'll have the vlan's
refcnt bumped up in all slaves, but it will never go down because it
failed to get added to the bond, so properly unwind the added vlan if
bond_add_vlan fails.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we have vlan_vids_add/del_by_dev() which serve the same purpose as
bond's bond_add/del_vlans_on_slave() with the good side effect of
reverting the changes if one of the additions fails.
There's only 1 change in the behaviour of enslave: if adding of the
vlans to the slave fails, we'll fail the enslaving because otherwise we
might delete some vlan that wasn't added by the bonding.
The only way this may happen is with ENOMEM currently, so we're in trouble
anyway.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ksz8873mll_read_status() is used only in this file.
Fix the following sparse warning:
drivers/net/phy/micrel.c:147:5: warning: symbol 'ksz8873mll_read_status' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To let it be reused and reduce code duplication. Also document this function.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WoL and power state changes will now be done in the shutdown handler.
open/close/ethtool will no longer change the power state. NVRAM
operations can now be permitted whether the device is up or down.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate MAC and PHY WoL setup code into a separate function.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
by closing the device if necessary. Otherwise, since NAPI state is
already disabled, a subsequent close will hang the system.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Uninitialized value was being returned in the non-failure case.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Log the event type for unknown async events
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BE2 FW GET_PHY_DETAILS cmd does not return fixed speeds supported.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SH-R and Lancer-R, use the FW supported values for Max unicast MACs,
Max VLANs and Max multicast MACs.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a chip wide value and the PFs already report it.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new speeds are supported by variants of the Skyhawk-R chip.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In our Fuz testing, reference client corrupts the dest mac to "00:00:00:00:00:00"
in the WPA2 handshake no 2. During driver init the sta_list entries mac
addresses are by default "00:00:00:00:00:00". Driver returns an invalid
pointer (conn) and the drver shall crash, if rxtids (aggr_conn)
skb queues are accessed, since they would not be initialized.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make sure to cancel heart beat timer before
freeing wmi to avoid potential NULL pointer
dereference.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Unify the PCI options location.
By default the SoC PS option is disabled to boost the
performance and due to poor stability on early HW revisions.
In future we can remove the module parameter and turn on/off
the PS for given hardware.
This change also makes the pci module parameter for SoC PS static.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A few places in the code (mac80211 and iwlmvm) use the same
TU_TO_JIFFIES() macro and could use TU_TO_EXP_TIME() that
mac80211 has. Make these available to everyone and use them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If scheduling an important time event fails, or if we get
an unexpected notification from the firmware, there isn't
much we can do to recover, so just drop the connection and
let higher layers retry it.
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
rs_ht_to_legacy and ant_toggle_lookup are arrays that
represent some state-machine. initialize them explicitly
with designated initialization to make them more clear
and avoid errors.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_mvm_mac_add_interface() didn't clean up beacon filtering
configuration and ctxt allocation in some error cases.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no reason for the transport to call itself through
indirect function pointers, inline the (little) code there
is and remove the indirection completely.
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
do some little cleanups in tx.c - eliminate duplicate checks,
use locally cached fields and predefined macros.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use a C99 initializer to clear the command and move the lockdep
assertion before the restart check. Since this causes problems
with the BUILD_BUG_ON() with some compilers, change that a bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When fewer than three antennas are connected (as is
always the case for the current devices), the signal
strength reporting was wrong; fix it.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The traffic load monitoring isn't used anymore to decide whether
a Tx aggregation on a specific TID should be started.
No point in collecting these statistics. Remove the relevant code.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If no opmode is present during suspend/resume (i.e. if
the iwldvm or iwlmvm isn't loaded) the driver crashes
during resume, trying to call the rfkill notification.
Avoid that, and also don't enable the rfkill interrupt
in this case (to avoid crashing trying to handle the
interrupt later.)
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a debugfs entry for the RX statistics received from
the firmware.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit a53ee0a308.
This fix causes a worse HW Error when entering RF-Kill.
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Otherwise, on neighbour creation, bond_neigh_init() will be called with a
foreign netdev.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup gfar_start_xmit()'s fast path by factoring out "redundant"
FCB insertion code (repeated gfar_add_fcb() calls and related)
and by reducing the number of if() clauses (i.e. if(fcb) checks).
Improve maintainability (e.g. there's less code and easier to read)
also by introducing do_csum and do_vlan to mark the other 2 Tx TOE
functionalities, following the same model as do_tstamp.
fcb_len may also be 0 now, to mark that Tx FCB insertion conditions
(do_csum, do_vlan, do_tstamp) have not been met.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both [eTSEC76] and [eTSEC12] errata relate to Tx checksum generation
(for some MPC83xx and MCP8548 older revisions). They require the same
workaround: manual checksum computation and insertion, and disabling
the H/W Tx csum acceleration feature (per frame) through Tx FCB
(Frame Control Block) csum offload settings.
The workaround for [eTSEC76] needs to be fixed because it currently
fails to disable H/W Tx csum insertion via FCB. This patch fixes it
and provides a common workaround implementation for both Tx csum errata.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're already protected by RTNL lock, so nothing can happen to bond/its
slaves, and thus the locking is useless here (both bond->lock and
bond->curr_active_slave).
Also, add ASSERT_RTNL() both to bond_set_rx_mode() and bond_hw_addr_swap()
to catch possible uses of it without RTNL locking.
This patch also saves us from a lockdep false-positive in
bond_set_rx_mode() vs bond_hw_addr_swap().
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new IP version has a minor changes and the offsets are same as the
previous version, so adding new IP version support in the driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we use a lot of time comparison math for arp_interval
comparisons, which are sometimes quite hard to read and understand.
All the time comparisons have one pattern:
(time - arp_interval_jiffies) <= jiffies <= (time + mod *
arp_interval_jiffies + arp_interval_jiffies/2)
Introduce a new helper - bond_time_in_interval(), which will do the math in
one place and, thus, will clean up the logical code. This helper introduces
a bit of overhead (by always calculating the jiffies from arp_interval),
however it's really not visible, considering that functions using it
usually run once in arp_interval milliseconds.
There are several lines slightly over 80 chars, however breaking them would
result in more hard-to-read code than several character after the 80 mark.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple cleanup to not call slave_last_rx() on every time function. It won't
give any measurable boost - but looks cleaner and easier to understand.
There are no time-consuming functions in between these calls, so it's safe
to call it in the beginning only once.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During a HW reset, the diversity config is programmed
in the set_board_values() eeprom callback, there is no
need to do it again by calling ath_ant_comb_update().
Fixed antenna support is not fully handled for 1-stream
cards, it can be done later.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
prism2_open() as an .ndo_open handler should not return positive numbers
in case of failure, but it does return 1 in a couple of places.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WB225 based cards like CUS198 and CUS230 support
both fast antenna diversity and LNA combining. Add support
for this and also program the SWCOM register with the
correct "ant_ctrl_comm2g_switch_enable" value.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CUS198/CUS230 cards require a custom value to be
programmed into the SWCOM register. Assign this during
init time.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This variable is redundant since we can use
common->bt_ant_diversity to determine if diversity
has to be enabled/disabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MC_GAIN_CTL/CCK_DETECT registers have to be programmed
with the correct configuration values if WLAN/BT RX diversity
is enabled. Add this and also take care of the BTCOEX mode
when fast diversity is enabled/disabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A custom solution for Asus is WB195 based and supports
WLAN/BT Rx diversity. Identify this card and set the
capability.
CUS198/CUS230, which are based on WB225 also support
WLAN/BT Rx diversity.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use "ath9k_hw_set_bt_ant_diversity" instead.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make use of this capability to restrict the usage of the
debugfs file and modparam using which this feature can
be enabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For single-chain WLAN+BT cards, the BT antenna can be used for
WLAN RX when the BT interface is disabled. Rename the modparam
"antenna_diversity" to "bt_ant_diversity" to clarify this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CUS198/CUS230 need a few tweaks in the antenna diversity
algorithm to accomodate RSSI variation. Add a couple
of knobs to control low RSSI threshold and fast antenna
diversity bias values.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's an underlying race condition with the unjoin_work() call that is
sometimes triggered depending on scheduling order and the phase of the
moon. This doesn't fix the race condition, but it does remove the
ill-advised BUG_ON() call in an easily-recoverable situation.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the missing unlock before return from function tile_net_open()
in the error handling case.
Introduced by commit f3286a3af8.
(tile: support multiple mPIPE shims in tilegx network driver)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These local functions are used only in this file.
Fix the following sparse warnings:
drivers/net/ethernet/mellanox/mlx4/cmd.c:803:5: warning: symbol 'MLX4_CMD_UPDATE_QP_wrapper' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlx4/cmd.c:812:5: warning: symbol 'MLX4_CMD_GET_OP_REQ_wrapper' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlx4/cmd.c:1547:5: warning: symbol 'mlx4_master_immediate_activate_vlan_qos' was not declared. Should
it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These local functions are used only in this file.
Fix the following sparse warnings:
drivers/net/ethernet/micrel/ks8842.c:708:6: warning: symbol 'ks8842_handle_rx' was not declared. Should it be static?
drivers/net/ethernet/micrel/ks8842.c:718:6: warning: symbol 'ks8842_handle_tx' was not declared. Should it be static?
drivers/net/ethernet/micrel/ks8842.c:727:6: warning: symbol 'ks8842_handle_rx_overrun' was not declared. Should it be static?
drivers/net/ethernet/micrel/ks8842.c:735:6: warning: symbol 'ks8842_tasklet' was not declared. Should it be static?
drivers/net/ethernet/micrel/ks8851_mll.c:691:6: warning: symbol 'ks_enable_qmu' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These local functions are used only in this file.
Fix the following sparse warnings:
drivers/net/ethernet/emulex/benet/be_main.c:475:6: warning: symbol 'populate_erx_stats' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_main.c:1485:6: warning: symbol 'be_rx_compl_process_gro' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_main.c:2262:5: warning: symbol 'be_poll' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_main.c:3223:6: warning: symbol 'flash_cookie' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_main.c:3280:27: warning: symbol 'get_fsec_info' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_cmds.c:1013:5: warning: symbol 'be_cmd_mccq_ext_create' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_cmds.c:1071:5: warning: symbol 'be_cmd_mccq_org_create' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_cmds.c:3166:5: warning: symbol 'be_cmd_get_profile_config_mbox' was not declared. Should it be
static?
drivers/net/ethernet/emulex/benet/be_cmds.c:3194:5: warning: symbol 'be_cmd_get_profile_config_mccq' was not declared. Should it be
static?
drivers/net/ethernet/emulex/benet/be_roce.c:96:6: warning: symbol '_be_roce_dev_remove' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_roce.c:113:6: warning: symbol '_be_roce_dev_open' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_roce.c:129:6: warning: symbol '_be_roce_dev_close' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bna_rx_sm_stop_wait_entry(), bna_rx_sm_rxf_stop_wait_entry(),
bna_rx_sm_started_entry(), bna_rx_sm_cleanup_wait_entry(),
and bna_rx_sm_cleanup_wait() are used only in this file.
Fix the following sparse warnings:
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1423:1: warning: symbol 'bna_rx_sm_stop_wait_entry' was not declared. Should it be
static?
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1476:1: warning: symbol 'bna_rx_sm_rxf_stop_wait_entry' was not declared. Should it be
static?
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1532:1: warning: symbol 'bna_rx_sm_started_entry' was not declared. Should it be
static?
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1597:1: warning: symbol 'bna_rx_sm_cleanup_wait_entry' was not declared. Should it be
static?
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1602:1: warning: symbol 'bna_rx_sm_cleanup_wait' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove this code, per Dave Miller's request, since it is not being used
anywhere in the kernel.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit df8ef8f3aa
macvlan: add FDB bridge ops and macvlan flags
added a flags field to macvlan, which can be
controlled from userspace.
The idea is to make the interface future-proof
so we can add flags and not new fields.
However, flags value isn't validated, as a result,
userspace can't detect which flags are supported.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes interrupt-related issue when no
interfaces were running thus the device was
considered powered down.
The power_down() function isn't really powering
down the device. It simply assumed it won't
interrupt. This wasn't true in some cases and
could lead to paging failures upon FW indication
interrupt (i.e. FW crash) because some structures
aren't allocated in that device state.
One reason for that was that ar_pci->started
wasn't reset. The other is interrupts should've
been masked when teardown starts.
The patch reorganized interrupt setup and makes
sure ar_pci->started is reset accordingly.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The following is needed as well to fix warning/error about shifting a 32 bit
value 32 bits which occurs if building on 32 bit platform caused by conversion
to using dma_addr_t
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vxlan remote list is protected by RCU and guaranteed to be non-empty.
Split out the rcu and non-rcu access to the list to fix warning
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This old driver never checked for DMA mapping errors.
Causing splats with the new DMA mapping checks:
WARNING: at lib/dma-debug.c:937 check_unmap+0x47b/0x930()
skge 0000:01:09.0: DMA-API: device driver failed to check map
Add checks and unwind code.
Reported-by: poma <pomidorabelisima@gmail.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ax88179_tx_fixup() has quite complex code trying to push 8 bytes
of control data (len/mss), but fails to do it properly for TCP packets,
incurring an extra copy and point of memory allocation failure.
Lets use the simple and approved way.
dev->needed_headroom being 8, all frames should have 8 bytes of
headroom, so the extra copy should be unlikely anyway.
This patch should improve performance for TCP xmits.
Reported-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gabor Juhos