We now have two implementations for vmapping a whole object, one for
dma-buf and one for the ringbuffer. If we couple the mapping into the
obj->pages lifetime, then we can reuse an obj->mapping for both and at
the same time couple it into the shrinker. There is a third vmapping
routine in the cmdparser that maps only a range within the object, for
the time being that is left alone, but will eventually use these routines
in order to cache the mapping between invocations.
v2: Mark the failable kmalloc() as __GFP_NOWARN (vsyrjala)
v3: Call unpin_vmap from the right dmabuf unmapper
v4: Rename vmap to map as we don't wish to imply the type of mapping
involved, just that it contiguously maps the object into kernel space.
Add kerneldoc and lockdep annotations
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-4-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Seal the request and mark it as pending execution before we submit it to
hardware. We assume that the actual submission cannot fail (that
guarantee is provided by preallocating space in the request for the
submission). As we may inspect this state without holding any locks
during hangcheck we should apply a barrier to ensure that we do
not see a more recent value in the HWS than we are tracking.
Based on a patch by Mika Kuoppala.
Suggested-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460010558-10705-8-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Since we are setting engine local values that are tied to the hardware,
move it out of i915_gem_init_seqno() into the intel_ring_init_seqno()
backend, next to where the other hw semaphore registers are written.
v2: Make the explanatory comment about always resetting the semaphores to
0 irrespective of the value of the reset seqno.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460010558-10705-4-git-send-email-chris@chris-wilson.co.uk
After the GPU reset and we discard all of the incomplete requests, mark
the GPU as having advanced to the last_submitted_seqno (as having
completed the requests and ready for fresh work). The impact of this is
negligible, as all the requests will be considered completed by this
point, it just brings the HWS into line with expectations for external
viewers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460010558-10705-2-git-send-email-chris@chris-wilson.co.uk
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Doing a lot of work in the interrupt handler introduces huge
latencies to the system as a whole.
Most dramatic effect can be seen by running an all engine
stress test like igt/gem_exec_nop/all where, when the kernel
config is lean enough, the whole system can be brought into
multi-second periods of complete non-interactivty. That can
look for example like this:
NMI watchdog: BUG: soft lockup - CPU#0 stuck for 23s! [kworker/u8:3:143]
Modules linked in: [redacted for brevity]
CPU: 0 PID: 143 Comm: kworker/u8:3 Tainted: G U L 4.5.0-160321+ #183
Hardware name: Intel Corporation Broadwell Client platform/WhiteTip Mountain 1
Workqueue: i915 gen6_pm_rps_work [i915]
task: ffff8800aae88000 ti: ffff8800aae90000 task.ti: ffff8800aae90000
RIP: 0010:[<ffffffff8104a3c2>] [<ffffffff8104a3c2>] __do_softirq+0x72/0x1d0
RSP: 0000:ffff88014f403f38 EFLAGS: 00000206
RAX: ffff8800aae94000 RBX: 0000000000000000 RCX: 00000000000006e0
RDX: 0000000000000020 RSI: 0000000004208060 RDI: 0000000000215d80
RBP: ffff88014f403f80 R08: 0000000b1b42c180 R09: 0000000000000022
R10: 0000000000000004 R11: 00000000ffffffff R12: 000000000000a030
R13: 0000000000000082 R14: ffff8800aa4d0080 R15: 0000000000000082
FS: 0000000000000000(0000) GS:ffff88014f400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fa53b90c000 CR3: 0000000001a0a000 CR4: 00000000001406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Stack:
042080601b33869f ffff8800aae94000 00000000fffc2678 ffff88010000000a
0000000000000000 000000000000a030 0000000000005302 ffff8800aa4d0080
0000000000000206 ffff88014f403f90 ffffffff8104a716 ffff88014f403fa8
Call Trace:
<IRQ>
[<ffffffff8104a716>] irq_exit+0x86/0x90
[<ffffffff81031e7d>] smp_apic_timer_interrupt+0x3d/0x50
[<ffffffff814f3eac>] apic_timer_interrupt+0x7c/0x90
<EOI>
[<ffffffffa01c5b40>] ? gen8_write64+0x1a0/0x1a0 [i915]
[<ffffffff814f2b39>] ? _raw_spin_unlock_irqrestore+0x9/0x20
[<ffffffffa01c5c44>] gen8_write32+0x104/0x1a0 [i915]
[<ffffffff8132c6a2>] ? n_tty_receive_buf_common+0x372/0xae0
[<ffffffffa017cc9e>] gen6_set_rps_thresholds+0x1be/0x330 [i915]
[<ffffffffa017eaf0>] gen6_set_rps+0x70/0x200 [i915]
[<ffffffffa0185375>] intel_set_rps+0x25/0x30 [i915]
[<ffffffffa01768fd>] gen6_pm_rps_work+0x10d/0x2e0 [i915]
[<ffffffff81063852>] ? finish_task_switch+0x72/0x1c0
[<ffffffff8105ab29>] process_one_work+0x139/0x350
[<ffffffff8105b186>] worker_thread+0x126/0x490
[<ffffffff8105b060>] ? rescuer_thread+0x320/0x320
[<ffffffff8105fa64>] kthread+0xc4/0xe0
[<ffffffff8105f9a0>] ? kthread_create_on_node+0x170/0x170
[<ffffffff814f351f>] ret_from_fork+0x3f/0x70
[<ffffffff8105f9a0>] ? kthread_create_on_node+0x170/0x170
I could not explain, or find a code path, which would explain
a +20 second lockup, but from some instrumentation it was
apparent the interrupts off proportion of time was between
10-25% under heavy load which is quite bad.
When a interrupt "cliff" is reached, which was >~320k irq/s on
my machine, the whole system goes into a terrible state of the
above described multi-second lockups.
By moving the GT interrupt handling to a tasklet in a most
simple way, the problem above disappears completely.
Testing the effect on sytem-wide latencies using
igt/gem_syslatency shows the following before this patch:
gem_syslatency: cycles=1532739, latency mean=416531.829us max=2499237us
gem_syslatency: cycles=1839434, latency mean=1458099.157us max=4998944us
gem_syslatency: cycles=1432570, latency mean=2688.451us max=1201185us
gem_syslatency: cycles=1533543, latency mean=416520.499us max=2498886us
This shows that the unrelated process is experiencing huge
delays in its wake-up latency. After the patch the results
look like this:
gem_syslatency: cycles=808907, latency mean=53.133us max=1640us
gem_syslatency: cycles=862154, latency mean=62.778us max=2117us
gem_syslatency: cycles=856039, latency mean=58.079us max=2123us
gem_syslatency: cycles=841683, latency mean=56.914us max=1667us
Showing a huge improvement in the unrelated process wake-up
latency. It also shows an approximate halving in the number
of total empty batches submitted during the test. This may
not be worrying since the test puts the driver under
a very unrealistic load with ncpu threads doing empty batch
submission to all GPU engines each.
Another benefit compared to the hard-irq handling is that now
work on all engines can be dispatched in parallel since we can
have up to number of CPUs active tasklets. (While previously
a single hard-irq would serially dispatch on one engine after
another.)
More interesting scenario with regards to throughput is
"gem_latency -n 100" which shows 25% better throughput and
CPU usage, and 14% better dispatch latencies.
I did not find any gains or regressions with Synmark2 or
GLbench under light testing. More benchmarking is certainly
required.
v2:
* execlists_lock should be taken as spin_lock_bh when
queuing work from userspace now. (Chris Wilson)
* uncore.lock must be taken with spin_lock_irq when
submitting requests since that now runs from either
softirq or process context.
v3:
* Expanded commit message with more testing data;
* converted missed locking sites to _bh;
* added execlist_lock comment. (Chris Wilson)
v4:
* Mention dispatch parallelism in commit. (Chris Wilson)
* Do not hold uncore.lock over MMIO reads since the block
is already serialised per-engine via the tasklet itself.
(Chris Wilson)
* intel_lrc_irq_handler should be static. (Chris Wilson)
* Cancel/sync the tasklet on GPU reset. (Chris Wilson)
* Document and WARN that tasklet cannot be active/pending
on engine cleanup. (Chris Wilson/Imre Deak)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Testcase: igt/gem_exec_nop/all
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94350
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1459768316-6670-1-git-send-email-tvrtko.ursulin@linux.intel.com
Refer to the GGTT VM consistently as "ggtt->base" instead of just "ggtt",
"vm" or indirectly through other variables like "dev_priv->ggtt.base"
to avoid confusion with the i915_ggtt object itself and PPGTT VMs.
Refer to the GGTT as "ggtt" instead of indirectly through chaining.
As a bonus gets rid of the long-standing i915_obj_to_ggtt vs.
i915_gem_obj_to_ggtt conflict, due to removal of i915_obj_to_ggtt!
v2:
- Added some more after grepping sources with Chris
v3:
- Refer to GGTT VM through ggtt->base consistently instead of ggtt_vm
(Chris)
v4:
- Convert all dev_priv->ggtt->foo accesses to ggtt->foo.
v5:
- Make patch checker happy
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Rename and document the GGTT init functions to give a better
idea of the context where they are called from.
i915_gem_gtt_init => i915_ggtt_init_hw
i915_gem_init_global_gtt => i915_gem_init_ggtt
i915_global_gtt_cleanup => i915_ggtt_cleanup_hw
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458830866-12578-1-git-send-email-joonas.lahtinen@linux.intel.com
Lets BUG_ON and don't bother with a WARN and returning an error, so we can
remove the need to pollute the code with error handling, after all it is
a programmer error to provide NULL view. Also while we're here remove
redundant NULL ggtt_view check.
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458834860-7898-1-git-send-email-matthew.auld@intel.com
Having provided for_each_engine_id() for cases where the third (id)
argument is useful, we can now replace all the remaining instances with
a simpler version that takes only two parameters. In many cases, this
also allows the elimination of the local variable used in the iterator
(usually 'i').
v2:
s/dev_priv/(dev_priv__)/ in body of for_each_engine_masked() [Chris Wilson]
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458757194-17783-2-git-send-email-david.s.gordon@intel.com
Refer to Global GTT consistently as GGTT, thus rename dev_priv->gtt
to dev_priv->ggtt and struct i915_gtt to struct i915_ggtt.
Fix a couple of whitespace problems while at it.
v2:
- Fix a typo in commit message.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Where we have a request we can use req->i915 directly instead
of going through the engine and device. Coccinelle script:
@@
function f;
identifier r;
@@
f(..., struct drm_i915_gem_request *r, ...)
{
...
- engine->dev->dev_private
+ r->i915
...
}
@@
struct drm_i915_gem_request *req;
@@
(
req->
- engine->dev->dev_private
+ i915
)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458219850-21007-1-git-send-email-tvrtko.ursulin@linux.intel.com
The only steps requiring device access is the fence and swizzling
initialization, so split these out keeping them in their current place
and move the rest of init steps earlier.
v2-v3:
- unchanged
v4:
- move call to i915_gem_detect_bit_6_swizzle() to
i915_gem_load_init_fences() and preserve the original order of
the detection of HW fence capailities wrt. swizzling (Chris)
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458132843-21860-1-git-send-email-imre.deak@intel.com
In full gpu reset we prime all engines and reset domains corresponding to
each engine. Per engine reset is just a special case of this process
wherein only a single engine is reset. This change is aimed to modify
relevant functions to achieve this. There are some other steps we carry out
in case of engine reset which are addressed in later patches.
Reset func now accepts a mask of all engines that need to be reset. Where
per engine resets are supported, error handler populates the mask
accordingly otherwise all engines are specified.
v2: ALL_ENGINES mask fixup, better for_each_ring_masked (Chris)
v3: Whitespace fixes (Chris)
v4: Rebase due to s/ring/engine
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458143640-20563-1-git-send-email-mika.kuoppala@intel.com
Some trivial ones, first pass done with Coccinelle:
@@
@@
(
- I915_NUM_RINGS
+ I915_NUM_ENGINES
|
- intel_ring_flag
+ intel_engine_flag
|
- for_each_ring
+ for_each_engine
|
- i915_gem_request_get_ring
+ i915_gem_request_get_engine
|
- intel_ring_idle
+ intel_engine_idle
|
- i915_gem_reset_ring_status
+ i915_gem_reset_engine_status
|
- i915_gem_reset_ring_cleanup
+ i915_gem_reset_engine_cleanup
|
- init_ring_lists
+ init_engine_lists
)
But that didn't fully work so I cleaned it up with:
for f in *.[hc]; do sed -i -e s/I915_NUM_RINGS/I915_NUM_ENGINES/ $f; done
for f in *.[hc]; do sed -i -e s/i915_gem_request_get_ring/i915_gem_request_get_engine/ $f; done
for f in *.[hc]; do sed -i -e s/intel_ring_flag/intel_engine_flag/ $f; done
for f in *.[hc]; do sed -i -e s/intel_ring_idle/intel_engine_idle/ $f; done
for f in *.[hc]; do sed -i -e s/init_ring_lists/init_engine_lists/ $f; done
for f in *.[hc]; do sed -i -e s/i915_gem_reset_ring_cleanup/i915_gem_reset_engine_cleanup/ $f; done
for f in *.[hc]; do sed -i -e s/i915_gem_reset_ring_status/i915_gem_reset_engine_status/ $f; done
v2: Rebase.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
commit e5756c10d8
Author: Imre Deak <imre.deak@intel.com>
Date: Fri Aug 14 18:43:30 2015 +0300
drm/i915/bxt: don't allow cached GEM mappings on A stepping
Added an exception of disallowing snooping for Broxton A
stepping hardware but userptr was still enabling it regardless.
Move the check to HAS_SNOOP now that it is used from multiple
call sites and use it.
v2: Userptr cannot be supported when it cannot be coherent and
generalize the code better. (Chris Wilson)
v3: Make has_snoop true only when !has_llc. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1456920631-34302-1-git-send-email-tvrtko.ursulin@linux.intel.com
The multiple levels of indirect do nothing but hinder the compiler and
the pointer chasing turns to be quite painful but painless to fix.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456484600-11477-1-git-send-email-tvrtko.ursulin@linux.intel.com
Elsewhere we have adopted the convention of using '_link' to denote
elements in the list (and '_list' for the actual list_head itself), and
that the name should indicate which list the link belongs to (and
preferrably not just where the link is being stored).
s/vma_link/obj_link/ (we iterate over obj->vma_list)
s/mm_list/vm_link/ (we iterate over vm->[in]active_list)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
This behavior of checking for a shmem backed GEM object was introduced here:
commit 4c914c0c7c
Author: Brad Volkin <bradley.d.volkin@intel.com>
Date: Tue Feb 18 10:15:45 2014 -0800
drm/i915: Refactor shmem pread setup
It is possible for an object to not be a shmem backed GEM object (for example
userptr objects). An example of how we hit this failure can be found through
copy_batch() in the command parser because we allocate a userptr object for the
batch which contains privileged instructions. Userptr calls
drm_gem_private_object_init() which explicitly sets the filp to none.
NOTE: I manually retyped this from a test machine. So I haven't even compiled
this exact patch.
v2: Use same logic as from a2a4f916c2f (Kristian, Dave Gordon)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Kristian Høgsberg <krh@bitplanet.net>
Cc: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Tested-by: Jordan Justen <jordan.l.justen@intel.com> (v1)
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455047053-2644-1-git-send-email-benjamin.widawsky@intel.com
We know this never runs from interrupt context so
don't need to use the flags variant.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Swap the order of context & engine cleanup, so that contexts are cleaned
up first, and *then* engines. This is a more sensible order anyway, but
in particular has become necessary since the 'intel_ring_initialized()
must be simple and inline' patch, which now uses ring->dev as an
'initialised' flag, so it can now be NULL after engine teardown. This
in turn can cause a problem in the context code, which (used to) check
the ring->dev->struct_mutex -- causing a fault if ring->dev was NULL.
Also rename the cleanup function to reflect what it actually does
(cleanup engines, not a ringbuffer), and fix an annoying whitespace issue.
v2: Also make the fix in i915_load_modeset_init, not just in
i915_driver_unload (Chris Wilson)
v3: Had extra stuff in it.
v4: Reverted extra stuff (so we're back to v2).
Rebased and updated commentary above (Dave Gordon).
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: David Gordon <david.s.gordon@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1453504211-7982-2-git-send-email-david.s.gordon@intel.com
commit 033908aed5
Author: Dave Gordon <david.s.gordon@intel.com>
Date: Thu Dec 10 18:51:23 2015 +0000
drm/i915: mark GEM object pages dirty when mapped & written by the CPU
introduced a check into i915_gem_object_get_dirty_pages() that returned
a NULL pointer when called with a bad object, one that was not backed by
shmemfs. This WARN was too strict as we can work on all struct page
backed objects, and resulted in a WARN + GPF for existing userspace. In
order to differentiate the various types of objects, add a new flags field
to the i915_gem_object_ops struct to describe their capabilities, with
the first flag being whether the object has struct pages.
v2: Drop silly const before an integer in the structure declaration.
Testcase: igt/gem_userptr_blits/relocations
Reported-and-tested-by: Kristian Høgsberg Kristensen <krh@bitplanet.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Kristian Høgsberg Kristensen <krh@bitplanet.net>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Kristian Høgsberg Kristensen <krh@bitplanet.net>
Tested-by: Michal Winiarski <michal.winiarski@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453487551-16799-1-git-send-email-chris@chris-wilson.co.uk
Previously intel_lr_context_(un)pin were operating on requests
which is in conflict with their names.
If we make them take a context and an engine, it makes the names
make more sense and it also makes future fixes possible.
v2: Rebase for default_context/kernel_context change.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Nick Hoath <nicholas.hoath@intel.com>
Factor out common clean-up code for the GEM load time init function.
Also rename i915_gem_load() to i915_gem_load_init() to have a better
match with its new clean-up function.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453209992-25995-5-git-send-email-imre.deak@intel.com
Factor out the common GEM shrinker clean-up code and call the shrinker
init function from the same function from where the corresponding
shrinker clean-up function is called. Also add sanity checking to the
shrinker and OOM registration calls.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453209992-25995-4-git-send-email-imre.deak@intel.com
Swap the order of context & engine cleanup, so that contexts are cleaned
up first, and *then* engines. This is a more sensible order anyway, but
in particular has become necessary since the 'intel_ring_initialized()
must be simple and inline' patch, which now uses ring->dev as an
'initialised' flag, so it can now be NULL after engine teardown. This
in turn can cause a problem in the context code, which (used to) check
the ring->dev->struct_mutex -- causing a fault if ring->dev was NULL.
Also rename the cleanup function to reflect what it actually does
(cleanup engines, not a ringbuffer), and fix an annoying whitespace issue.
v2: Also make the fix in i915_load_modeset_init, not just in
i915_driver_unload (Chris Wilson)
v3: Had extra stuff in it.
v4: Reverted extra stuff (so we're back to v2).
Rebased and updated commentary above (Dave Gordon).
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1453405067-32890-3-git-send-email-david.s.gordon@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tvrtko was looking through the execbuffer-ioctl and noticed that the
uABI was tightly coupled to our internal engine identifiers. Close
inspection also revealed that we leak those internal engine identifiers
through the busy-ioctl, and those internal identifiers already do not
match the user identifiers. Fortuitiously, there is only one user of the
set of busy rings from the busy-ioctl, and they only wish to choose
between the RENDER and the BLT engines.
Let's fix the userspace ABI while we still can.
v2: Update the uAPI documentation to explain the identifiers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Testcase: igt/gem_busy
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1452876706-21620-1-git-send-email-chris@chris-wilson.co.uk
At the moment execbuf ring selection is fully coupled to
internal ring ids which is not a good thing on its own.
This dependency is also spread between two source files and
not spelled out at either side which makes it hidden and
fragile.
This patch decouples this dependency by introducing an explicit
translation table of execbuf uAPI to ring id close to the only
call site (i915_gem_do_execbuffer).
This way we are free to change driver internal implementation
details without breaking userspace. All state relating to the
uAPI is now contained in, or next to, i915_gem_do_execbuffer.
As a side benefit, this patch decreases the compiled size
of i915_gem_do_execbuffer.
v2: Extract ring selection into eb_select_ring. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1452870770-13981-1-git-send-email-tvrtko.ursulin@linux.intel.com
There are a few bits of code which the transformations implemented by
the previous patch reveal to be suboptimal, once the notion of a per-
ring default context has gone away. So this tidies up the leftovers.
It could have been squashed into the previous patch, but that would have
made that patch less clearly a simple transformation. In particular, any
change which alters the code block structure or indentation has been
deferred into this separate patch, because such things tend to make
diffs more difficult to read.
v4: Rebased
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453230175-19330-4-git-send-email-david.s.gordon@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we've eliminated a lot of uses of ring->default_context,
we can eliminate the pointer itself.
All the engines share the same default intel_context, so we can just
keep a single reference to it in the dev_priv structure rather than one
in each of the engine[] elements. This make refcounting more sensible
too, as we now have a refcount of one for the one pointer, rather than
a refcount of one but multiple pointers.
From an idea by Chris Wilson.
v2: transform an extra instance of ring->default_context introduced by
42f1cae8c drm/i915: Restore inhibiting the load of the default context
That patch's commentary includes:
v2: Mark the global default context as uninitialized on GPU reset so
that the context-local workarounds are reloaded upon re-enabling
The code implementing that now also benefits from the replacement of
the multiple (per-ring) pointers to the default context with a single
pointer to the unique kernel context.
v4: Rebased, remove underused local (Nick Hoath)
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1453230175-19330-3-git-send-email-david.s.gordon@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are a number of places where the driver needs a request, but isn't
working on behalf of any specific user or in a specific context. At
present, we associate them with the per-engine default context. A future
patch will abolish those per-engine context pointers; but we can already
eliminate a lot of the references to them, just by making the allocator
allow NULL as a shorthand for "an appropriate context for this ring",
which will mean that the callers don't need to know anything about how
the "appropriate context" is found (e.g. per-ring vs per-device, etc).
So this patch renames the existing i915_gem_request_alloc(), and makes
it local (static inline), and replaces it with a wrapper that provides
a default if the context is NULL, and also has a nicer calling
convention (doesn't require a pointer to an output parameter). Then we
change all callers to use the new convention:
OLD:
err = i915_gem_request_alloc(ring, user_ctx, &req);
if (err) ...
NEW:
req = i915_gem_request_alloc(ring, user_ctx);
if (IS_ERR(req)) ...
OLD:
err = i915_gem_request_alloc(ring, ring->default_context, &req);
if (err) ...
NEW:
req = i915_gem_request_alloc(ring, NULL);
if (IS_ERR(req)) ...
v4: Rebased
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453230175-19330-2-git-send-email-david.s.gordon@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No need to call ktime_get_raw_ns twice per unlimited wait and can
also elimate a local variable.
v2: Added comment about silencing the compiler warning. (Daniel Vetter)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1452870672-13901-1-git-send-email-tvrtko.ursulin@linux.intel.com
misc i915 fixes all over the place.
* tag 'drm-intel-next-fixes-2016-01-14' of git://anongit.freedesktop.org/drm-intel:
drm/i915/gen9: Set PIN_ZONE_4G end to 4GB - 1 page
drm/i915: Widen return value for reservation_object_wait_timeout_rcu to long.
drm/i915: intel_hpd_init(): Fix suspend/resume reprobing
drm/i915: shut up gen8+ SDE irq dmesg noise, again
drm/i915: Restore inhibiting the load of the default context
drm/i915: Tune down rpm wakelock debug checks
drm/i915: Avoid writing relocs with addresses in non-canonical form
drm/i915: Move Braswell stop_machine GGTT insertion workaround
Kernel and userspace are able to handle 4GB (1<<32) address space range,
but "A32 Stateless Model" is not. According to documentation, A32 accesses
are based on General State Base Address and bound checking is in place.
Because size field (instruction State Base Address) limitation, it is not
possible to address full 4GB memory region.
A32 Stateless Model is used by some libraries and without this patch, the
last page of 4GB address space is not accessible in 32bit processes.
Reported-by: Artur Harasimiuk <artur.harasimiuk@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452512367-23614-1-git-send-email-michel.thierry@intel.com
Cc: drm-intel-fixes@lists.freedesktop.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 1892faa9ec)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
- fix atomic watermark recomputation logic (Maarten)
- modeset sequence fixes for LPT (Ville)
- more kbl enabling&prep work (Rodrigo, Wayne)
- first bits for mst audio
- page dirty tracking fixes from Dave Gordon
- new get_eld hook from Takashi, also included in the sound tree
- fixup cursor handling when placed at address 0 (Ville)
- refactor VBT parsing code (Jani)
- rpm wakelock debug infrastructure ( Imre)
- fbdev is pinned again (Chris)
- tune the busywait logic to avoid wasting cpu cycles (Chris)
* tag 'drm-intel-next-2015-12-18' of git://anongit.freedesktop.org/drm-intel: (81 commits)
drm/i915: Update DRIVER_DATE to 20151218
drm/i915/skl: Default to noncoherent access up to F0
drm/i915: Only spin whilst waiting on the current request
drm/i915: Limit the busy wait on requests to 5us not 10ms!
drm/i915: Break busywaiting for requests on pending signals
drm/i915: don't enable autosuspend on platforms without RPM support
drm/i915/backlight: prefer dev_priv over dev pointer
drm/i915: Disable primary plane if we fail to reconstruct BIOS fb (v2)
drm/i915: Pin the ifbdev for the info->system_base GGTT mmapping
drm/i915: Set the map-and-fenceable flag for preallocated objects
drm/i915: mdelay(10) considered harmful
drm/i915: check that we are in an RPM atomic section in GGTT PTE updaters
drm/i915: add support for checking RPM atomic sections
drm/i915: check that we hold an RPM wakelock ref before we put it
drm/i915: add support for checking if we hold an RPM reference
drm/i915: use assert_rpm_wakelock_held instead of opencoding it
drm/i915: add assert_rpm_wakelock_held helper
drm/i915: remove HAS_RUNTIME_PM check from RPM get/put/assert helpers
drm/i915: get a permanent RPM reference on platforms w/o RPM support
drm/i915: refactor RPM disabling due to RC6 being disabled
...
Limit busywaiting only to the request currently being processed by the
GPU. If the request is not currently being processed by the GPU, there
is a very low likelihood of it being completed within the 2 microsecond
spin timeout and so we will just be wasting CPU cycles.
v2: Check for logical inversion when rebasing - we were incorrectly
checking for this request being active, and instead busywaiting for
when the GPU was not yet processing the request of interest.
v3: Try another colour for the seqno names.
v4: Another colour for the function names.
v5: Remove the forced coherency when checking for the active request. On
reflection and plenty of recent experimentation, the issue is not a
cache coherency problem - but an irq/seqno ordering problem (timing issue).
Here, we do not need the w/a to force ordering of the read with an
interrupt.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: "Rogozhkin, Dmitry V" <dmitry.v.rogozhkin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Eero Tamminen <eero.t.tamminen@intel.com>
Cc: "Rantala, Valtteri" <valtteri.rantala@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449833608-22125-4-git-send-email-chris@chris-wilson.co.uk
When waiting for high frequency requests, the finite amount of time
required to set up the irq and wait upon it limits the response rate. By
busywaiting on the request completion for a short while we can service
the high frequency waits as quick as possible. However, if it is a slow
request, we want to sleep as quickly as possible. The tradeoff between
waiting and sleeping is roughly the time it takes to sleep on a request,
on the order of a microsecond. Based on measurements of synchronous
workloads from across big core and little atom, I have set the limit for
busywaiting as 10 microseconds. In most of the synchronous cases, we can
reduce the limit down to as little as 2 miscroseconds, but that leaves
quite a few test cases regressing by factors of 3 and more.
The code currently uses the jiffie clock, but that is far too coarse (on
the order of 10 milliseconds) and results in poor interactivity as the
CPU ends up being hogged by slow requests. To get microsecond resolution
we need to use a high resolution timer. The cheapest of which is polling
local_clock(), but that is only valid on the same CPU. If we switch CPUs
because the task was preempted, we can also use that as an indicator that
the system is too busy to waste cycles on spinning and we should sleep
instead.
__i915_spin_request was introduced in
commit 2def4ad99b [v4.2]
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Apr 7 16:20:41 2015 +0100
drm/i915: Optimistically spin for the request completion
v2: Drop full u64 for unsigned long - the timer is 32bit wraparound safe,
so we can use native register sizes on smaller architectures. Mention
the approximate microseconds units for elapsed time and add some extra
comments describing the reason for busywaiting.
v3: Raise the limit to 10us
v4: Now 5us.
Reported-by: Jens Axboe <axboe@kernel.dk>
Link: https://lkml.org/lkml/2015/11/12/621
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: "Rogozhkin, Dmitry V" <dmitry.v.rogozhkin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Eero Tamminen <eero.t.tamminen@intel.com>
Cc: "Rantala, Valtteri" <valtteri.rantala@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449833608-22125-3-git-send-email-chris@chris-wilson.co.uk
The busywait in __i915_spin_request() does not respect pending signals
and so may consume the entire timeslice for the task instead of
returning to userspace to handle the signal.
In the worst case this could cause a delay in signal processing of 20ms,
which would be a noticeable jitter in cursor tracking. If a higher
resolution signal was being used, for example to provide fairness of a
server timeslices between clients, we could expect to detect some
unfairness between clients (i.e. some windows not updating as fast as
others). This issue was noticed when inspecting a report of poor
interactivity resulting from excessively high __i915_spin_request usage.
Fixes regression from
commit 2def4ad99b [v4.2]
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Apr 7 16:20:41 2015 +0100
drm/i915: Optimistically spin for the request completion
v2: Try to assess the impact of the bug
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc; "Rogozhkin, Dmitry V" <dmitry.v.rogozhkin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Eero Tamminen <eero.t.tamminen@intel.com>
Cc: "Rantala, Valtteri" <valtteri.rantala@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449833608-22125-2-git-send-email-chris@chris-wilson.co.uk
As we mark the preallocated objects as bound, we should also flag them
correctly as being map-and-fenceable (if appropriate!) so that later
users do not get confused and try and rebind the pinned vma in order to
get a map-and-fenceable binding.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: "Goel, Akash" <akash.goel@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: drm-intel-fixes@lists.freedesktop.org
Link: http://patchwork.freedesktop.org/patch/msgid/1448029000-10616-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is the "fix igt basic test set issues" edition.
- more PSR fixes from Rodrigo, getting closer
- tons of fifo underrun fixes from Ville
- runtime pm fixes from Imre, Daniel Stone
- fix SDE interrupt handling properly (Jani Nikula)
- hsw/bdw fdi modeset sequence fixes (Ville)
- "don't register bad VGA connectors and fall over" fixes (Ville)
- more fbc fixes from Paulo
- and a grand total of exactly one feature item: Implement dma-buf/fence based
cross-driver sync in the i915 pageflip path (Alex Goins)
* tag 'drm-intel-next-2015-12-04-1' of git://anongit.freedesktop.org/drm-intel: (70 commits)
drm/i915: Update DRIVER_DATE to 20151204
drm/i915/skl: Add SKL GT4 PCI IDs
Revert "drm/i915: Extend LRC pinning to cover GPU context writeback"
drm/i915: Correct the Ref clock value for BXT
drm/i915: Restore skl_gt3 device info
drm/i915: Fix RPS pointer passed from wait_ioctl to i915_wait_request
Revert "drm/i915: Remove superfluous NULL check"
drm/i915: Clean up device info structure definitions
drm/i915: Remove superfluous NULL check
drm/i915: Handle cdclk limits on broadwell.
i915: wait for fence in prepare_plane_fb
i915: wait for fence in mmio_flip_work_func
drm/i915: Extend LRC pinning to cover GPU context writeback
drm/i915/guc: Clean up locks in GuC
drm/i915: only recompress FBC after flushing a drawing operation
drm/i915: get rid of FBC {,de}activation messages
drm/i915: kill fbc.uncompressed_size
drm/i915: use a single intel_fbc_work struct
drm/i915: check for FBC planes in the same place as the pipes
drm/i915: alloc/free the FBC CFB during enable/disable
...
Here are the patchset to add get_eld op to audio component for
communicating more directly between i915 and HD-audio.
Currently, the HDMI/DP audio status and ELD are notified and obtained
via the hardware-level communication over HD-audio unsolicited event
and verbs although the graphics driver holds the exactly same
information. As we already have a notification via audio component,
this is another step forward; namely, the audio driver may fetch
directly the audio status and ELD via the new component op.
The commits are based on Dave's latest drm-next branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=NShN
-----END PGP SIGNATURE-----
Merge tag 'drm-i915-get-eld' of tiwai/sound into drm-intel-next-queued
Add get_eld audio component for i915/HD-audio
Currently, the HDMI/DP audio status and ELD are notified and obtained
via the hardware-level communication over HD-audio unsolicited event
and verbs although the graphics driver holds the exactly same
information. As we already have a notification via audio component,
this is another step forward; namely, the audio driver may fetch
directly the audio status and ELD via the new component op.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
When creating a new (pageable) GEM object and filling it with data, we
must mark it as 'dirty', i.e. backing store is out-of-date w.r.t. the
newly-written content. This ensures that if the object is evicted under
memory pressure, its pages in the pagecache will be written to backing
store rather than discarded.
Based on an original version by Alex Dai.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1449773486-30822-3-git-send-email-david.s.gordon@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In various places, a single page of a (regular) GEM object is mapped into
CPU address space and updated. In each such case, either the page or the
the object should be marked dirty, to ensure that the modifications are
not discarded if the object is evicted under memory pressure.
The typical sequence is:
va = kmap_atomic(i915_gem_object_get_page(obj, pageno));
*(va+offset) = ...
kunmap_atomic(va);
Here we introduce i915_gem_object_get_dirty_page(), which performs the
same operation as i915_gem_object_get_page() but with the side-effect
of marking the returned page dirty in the pagecache. This will ensure
that if the object is subsequently evicted (due to memory pressure),
the changes are written to backing store rather than discarded.
Note that it works only for regular (shmfs-backed) GEM objects, but (at
least for now) those are the only ones that are updated in this way --
the objects in question are contexts and batchbuffers, which are always
shmfs-backed.
Separate patches deal with the cases where whole objects are (or may
be) dirtied.
v3: Mark two more pages dirty in the page-boundary-crossing
cases of the execbuffer relocation code [Chris Wilson]
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1449773486-30822-2-git-send-email-david.s.gordon@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When clearing an execlist queue, instead of traversing it and unreferencing all
requests while holding the spinlock (which might lead to thread sleeping with
IRQs are turned off - bad news!), just move all requests to the retire request
list while holding spinlock and then drop spinlock and invoke the execlists
request retirement path, which already deals with the intricacies of
purging/dereferencing execlist queue requests.
This patch can be considered v3 of:
commit b96db8b81c54ef30485ddb5992d63305d86ea8d3
Author: Tomas Elf <tomas.elf@intel.com>
drm/i915: Grab execlist spinlock to avoid post-reset concurrency issues
This patch assumes v2 of the above patch is part of the baseline, reverts v2
and adds changes on top to turn it into v3.
Signed-off-by: Tomas Elf <tomas.elf@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1445619757-19822-1-git-send-email-tomas.elf@intel.com
Reviewed-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Dave Gordon <dave.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Do some further clean up based on the initial review of
drm/i915: Separate cherryview from valleyview.
In this case remove a hack for VLV A0.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Wayne Boyer <wayne.boyer@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449514270-15171-4-git-send-email-wayne.boyer@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The cherryview device shares many characteristics with the valleyview
device. When support was added to the driver for cherryview, the
corresponding device info structure included .is_valleyview = 1.
This is not correct and leads to some confusion.
This patch changes .is_valleyview to .is_cherryview in the cherryview
device info structure and simplifies the IS_CHERRYVIEW macro.
Then where appropriate, instances of IS_VALLEYVIEW are replaced with
IS_VALLEYVIEW || IS_CHERRYVIEW or equivalent.
v2: Use IS_VALLEYVIEW || IS_CHERRYVIEW instead of defining a new macro.
Also add followup patches to fix issues discovered during the first
review. (Ville)
v3: Fix some style issues and one gen check. Remove CRT related changes
as CRT is not supported on CHV. (Imre, Ville)
v4: Make a few more optimizations. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Wayne Boyer <wayne.boyer@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449692975-14803-1-git-send-email-wayne.boyer@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Userspace can pass in an offset that it presumes the object is located
at. The kernel will then do its utmost to fit the object into that
location. The assumption is that userspace is handling its own object
locations (for example along with full-ppgtt) and that the kernel will
rarely have to make space for the user's requests.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
v2: Fixed incorrect eviction found by Michal Winiarski - fix suggested by Chris
Wilson. Fixed incorrect error paths causing crash found by Michal Winiarski.
(Not published externally)
v3: Rebased because of trivial conflict in object_bind_to_vm. Fixed eviction
to allow eviction of soft-pinned objects when another soft-pinned object used
by a subsequent execbuffer overlaps reported by Michal Winiarski.
(Not published externally)
v4: Moved soft-pinned objects to the front of ordered_vmas so that they are
pinned first after an address conflict happens to avoid repeated conflicts in
rare cases (Suggested by Chris Wilson). Expanded comment on
drm_i915_gem_exec_object2.offset to cover this new API.
v5: Added I915_PARAM_HAS_EXEC_SOFTPIN parameter for detecting this capability
(Kristian). Added check for multiple pinnings on eviction (Akash). Made sure
buffers are not considered misplaced without the user specifying
EXEC_OBJECT_SUPPORTS_48B_ADDRESS. User must assume responsibility for any
addressing workarounds. Updated object2.offset field comment again to clarify
NO_RELOC case (Chris). checkpatch cleanup.
v6: Trivial rebase on latest drm-intel-nightly
v7: Catch attempts to pin above the max virtual address size and return
EINVAL (Tvrtko). Decouple EXEC_OBJECT_SUPPORTS_48B_ADDRESS and
EXEC_OBJECT_PINNED flags, user must pass both flags in any attempt to pin
something at an offset above 4GB (Chris, Daniel Vetter).
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Akash Goel <akash.goel@intel.com>
Cc: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Zou Nanhai <nanhai.zou@intel.com>
Cc: Kristian Høgsberg <hoegsberg@gmail.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Acked-by: PDT
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449575707-20933-1-git-send-email-thomas.daniel@intel.com
This was in the documentation for modeset helper hooks, where it is a
bit misplaced.
v2: Reindent the drm_mode_status enum, inspired by Ville.
v3: Suggestions from Ville and Thierry.
v4: Small fixup that 0day spotted.
v5: Slight change to avoid accidental headings in kerneldoc output.
Cc: ville.syrjala@linux.intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-27-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v3)
Reviewed-by: Thierry Reding <treding@nvidia.com> (v3)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWZMgaAAoJEHm+PkMAQRiGGcIH+gNS/hbN2DKW7wphl1QuaV7C
1fror8AvpwbGa/o0yuxovaVuZzAR0TF31vn+gAemF4U/hnM25xqxEHXYZEVv8OWw
mbz4/z+jbVk3SiS5AiZPIZgL4W6RZnG5QYfiTVGPlBHuBznW2ITlNlClBOmBL45o
uhb3bjTzi70AZ7Gh6i9sHgJoHg6D9u/ZxLaLcWnM79BzyTMHTf2t0wnrQmh66lEE
hp7Rn9wXv9bk/e3iH7CVUb97P4IWhhkmfqcoturqAg9+C/M26b0VmvQp9Sy8S6Pd
FVQ+SUIZllj5ZDKe9mOcs37czlxTr0keEFqzWeMh/7y4iuI3RaRp/qb+7mX5sIE=
=WGZ1
-----END PGP SIGNATURE-----
Back merge tag 'v4.4-rc4' into drm-next
We've picked up a few conflicts and it would be nice
to resolve them before we move onwards.
This reverts commit 6d65ba943a.
Mika Kuoppala traced down a use-after-free crash in module unload to
this commit, because ring->last_context is leaked beyond when the
context gets destroyed. Mika submitted a quick fix to patch that up in
the context destruction code, but that's too much of a hack.
The right fix is instead for the ring to hold a full reference onto
it's last context, like we do for legacy contexts.
Since this is causing a regression in BAT it gets reverted before we
can close this.
Cc: Nick Hoath <nicholas.hoath@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Gordon <david.s.gordon@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Alex Dai <yu.dai@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93248
Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
In commit 2e1b873072 [v4.2]
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Apr 27 13:41:22 2015 +0100
drm/i915: Convert RPS tracking to a intel_rps_client struct
we converted the __i915_wait_request() to take a new intel_rps_client
struct (rather than having to pass fake drm_i915_file_private structs).
However, due to use of passing a void pointer, I didn't spot one
callsite in wait-ioctl was passing the wrong pointer.
Fwiw, the impact of this bug is zero. Along the rps path, we always
first call list_empty(rps) which when we pass in the wrong pointer
always evaluates to false and we return early and never chase the
invalid pointers.
The user visible impact is then wait-ioctl doesn't get the same
waitboosting as the other interfaces (set-domain, throttle), which is a
performance concern for the *very* few users of the wait interface.
There is also a libdrm_intel patch to use the wait-ioctl for
drm_intel_bo_wait_rendering() if anyone feels inclined to review
libdrm_intel patches.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: Add Chris' explanation for why the impact of this is pretty
close to 0.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the first retired request on a new context to unpin
the old context. This ensures that the hw context remains
bound until it has been written back to by the GPU.
Now that the context is pinned until later in the request/context
lifecycle, it no longer needs to be pinned from context_queue to
retire_requests.
This fixes an issue with GuC submission where the GPU might not
have finished writing back the context before it is unpinned. This
results in a GPU hang.
v2: Moved the new pin to cover GuC submission (Alex Dai)
Moved the new unpin to request_retire to fix coverage leak
v3: Added switch to default context if freeing a still pinned
context just in case the hw was actually still using it
v4: Unwrapped context unpin to allow calling without a request
v5: Only create a switch to idle context if the ring doesn't
already have a request pending on it (Alex Dai)
Rename unsaved to dirty to avoid double negatives (Dave Gordon)
Changed _no_req postfix to __ prefix for consistency (Dave Gordon)
Split out per engine cleanup from context_free as it
was getting unwieldy
Corrected locking (Dave Gordon)
v6: Removed some bikeshedding (Mika Kuoppala)
Added explanation of the GuC hang that this fixes (Daniel Vetter)
v7: Removed extra per request pinning from ring reset code (Alex Dai)
Added forced ring unpin/clean in error case in context free (Alex Dai)
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Issue: VIZ-4277
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Gordon <david.s.gordon@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Alex Dai <yu.dai@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have relied upon the sole caller (wait_ioctl) validating the timeout
argument. However, when waiting for multiple requests I forgot to ensure
that the timeout was still positive on the later requests. This is more
simply done inside __i915_wait_request.
Fixes regression introduced in
commit b47161858b
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Apr 27 13:41:17 2015 +0100
drm/i915: Implement inter-engine read-read optimisations
The impact of the regression is 1 jiffie for each extra active ring for
a wait_ioctl with a timeout -- I don't think anyone has noticed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1448544702-5594-1-git-send-email-chris@chris-wilson.co.uk
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWUmHZAAoJEHm+PkMAQRiGHtcH/RVRsn8re0WdRWYaTr9+Hknm
CGlRJN4LKecttgYQ/2bS1QsDbt8usDPBiiYVopqGXQxPBmjyDAqPjsa+8VzCaVc6
WA+9LDB+PcW28lD6BO+qSZCOAm7hHSZq7dtw9x658IqO+mI2mVeCybsAyunw2iWi
Kf5q90wq6tIBXuT8YH9MXGrSCQw00NclbYeYwB9CmCt9hT/koEFBdl7uFUFitB+Q
GSPTz5fXhgc5Lms85n7flZlrVKoQKmtDQe4/DvKZm+SjsATHU9ru89OxDBdS5gSG
YcEIM4zc9tMjhs3GC9t6WXf6iFOdctum8HOhUoIN/+LVfeOMRRwAhRVqtGJ//Xw=
=DCUg
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rc2' into drm-intel-next-queued
Linux 4.4-rc2
Backmerge to get at
commit 1b0e3a049e
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Nov 5 23:04:11 2015 +0200
drm/i915/skl: disable display side power well support for now
so that we can proplery re-eanble skl power wells in -next.
Conflicts are just adjacent lines changed, except for intel_fbdev.c
where we need to interleave the changs. Nothing nefarious.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
When register type safety happens, we can't just try to emit the
register itself to the ring. Instead we'll need to extract the
offset from it first. Add some convenience functions that will do
that.
v2: Convert MOCS setup too
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446672017-24497-20-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
After Damien's D3 fix I started to get runtime suspend residency for the
first time and that revealed a breakage on the set_caching IOCTL path
that accesses the HW but doesn't take an RPM ref. Fix this up.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Link: http://patchwork.freedesktop.org/patch/msgid/1446665132-22491-1-git-send-email-imre.deak@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
No need to verify VMA belongs to GGTT since:
1. The function must return a normal VMA belonging to passed in VM.
2. There can only be one normal VMA for any VM.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1447329595-17495-1-git-send-email-tvrtko.ursulin@linux.intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Pull drm updates from Dave Airlie:
"I Was Almost Tempted To Capitalise Every Word, but then I decided I
couldn't read it myself!
I've also got one pull request for the sti driver outstanding. It
relied on a commit in Greg's tree and I didn't find out in time, that
commit is in your tree now so I might send that along once this is
merged.
I also had the accidental misfortune to have access to a Skylake on my
desk for a few days, and I've had to encourage Intel to try harder,
which seems to be happening now.
Here is the main drm-next pull request for 4.4.
Highlights:
New driver:
vc4 driver for the Rasberry Pi VPU.
(From Eric Anholt at Broadcom.)
Core:
Atomic fbdev support
Atomic helpers for runtime pm
dp/aux i2c STATUS_UPDATE handling
struct_mutex usage cleanups.
Generic of probing support.
Documentation:
Kerneldoc for VGA switcheroo code.
Rename to gpu instead of drm to reflect scope.
i915:
Skylake GuC firmware fixes
HPD A support
VBT backlight fallbacks
Fastboot by default for some systems
FBC work
BXT/SKL workarounds
Skylake deeper sleep state fixes
amdgpu:
Enable GPU scheduler by default
New atombios opcodes
GPUVM debugging options
Stoney support.
Fencing cleanups.
radeon:
More efficient CS checking
nouveau:
gk20a instance memory handling improvements.
Improved PGOB detection and GK107 support
Kepler GDDR5 PLL statbility improvement
G8x/GT2xx reclock improvements
new userspace API compatiblity fixes.
virtio-gpu:
Add 3D support - qemu 2.5 has it merged for it's gtk backend.
msm:
Initial msm88896 (snapdragon 8200)
exynos:
HDMI cleanups
Enable mixer driver byt default
Add DECON-TV support
vmwgfx:
Move to using memremap + fixes.
rcar-du:
Add support for R8A7793/4 DU
armada:
Remove support for non-component mode
Improved plane handling
Power savings while in DPMS off.
tda998x:
Remove unused slave encoder support
Use more HDMI helpers
Fix EDID read handling
dwhdmi:
Interlace video mode support for ipu-v3/dw_hdmi
Hotplug state fixes
Audio driver integration
imx:
More color formats support.
tegra:
Minor fixes/improvements"
[ Merge fixup: remove unused variable 'dev' that had all uses removed in
commit 4e270f088011: "drm/gem: Drop struct_mutex requirement from
drm_gem_mmap_obj" ]
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (764 commits)
drm/vmwgfx: Relax irq locking somewhat
drm/vmwgfx: Properly flush cursor updates and page-flips
drm/i915/skl: disable display side power well support for now
drm/i915: Extend DSL readout fix to BDW and SKL.
drm/i915: Do graphics device reset under forcewake
drm/i915: Skip fence installation for objects with rotated views (v4)
vga_switcheroo: Drop client power state VGA_SWITCHEROO_INIT
drm/amdgpu: group together common fence implementation
drm/amdgpu: remove AMDGPU_FENCE_OWNER_MOVE
drm/amdgpu: remove now unused fence functions
drm/amdgpu: fix fence fallback check
drm/amdgpu: fix stoping the scheduler timeout
drm/amdgpu: cleanup on error in amdgpu_cs_ioctl()
drm/i915: Fix locking around GuC firmware load
drm/amdgpu: update Fiji's Golden setting
drm/amdgpu: update Fiji's rev id
drm/amdgpu: extract common code in vi_common_early_init
drm/amd/scheduler: don't oops on failure to load
drm/amdgpu: don't oops on failure to load (v2)
drm/amdgpu: don't VT switch on suspend
...
There are many places which use mapping_gfp_mask to restrict a more
generic gfp mask which would be used for allocations which are not
directly related to the page cache but they are performed in the same
context.
Let's introduce a helper function which makes the restriction explicit and
easier to track. This patch doesn't introduce any functional changes.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Michal Hocko <mhocko@suse.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__GFP_WAIT was used to signal that the caller was in atomic context and
could not sleep. Now it is possible to distinguish between true atomic
context and callers that are not willing to sleep. The latter should
clear __GFP_DIRECT_RECLAIM so kswapd will still wake. As clearing
__GFP_WAIT behaves differently, there is a risk that people will clear the
wrong flags. This patch renames __GFP_WAIT to __GFP_RECLAIM to clearly
indicate what it does -- setting it allows all reclaim activity, clearing
them prevents it.
[akpm@linux-foundation.org: fix build]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__GFP_WAIT has been used to identify atomic context in callers that hold
spinlocks or are in interrupts. They are expected to be high priority and
have access one of two watermarks lower than "min" which can be referred
to as the "atomic reserve". __GFP_HIGH users get access to the first
lower watermark and can be called the "high priority reserve".
Over time, callers had a requirement to not block when fallback options
were available. Some have abused __GFP_WAIT leading to a situation where
an optimisitic allocation with a fallback option can access atomic
reserves.
This patch uses __GFP_ATOMIC to identify callers that are truely atomic,
cannot sleep and have no alternative. High priority users continue to use
__GFP_HIGH. __GFP_DIRECT_RECLAIM identifies callers that can sleep and
are willing to enter direct reclaim. __GFP_KSWAPD_RECLAIM to identify
callers that want to wake kswapd for background reclaim. __GFP_WAIT is
redefined as a caller that is willing to enter direct reclaim and wake
kswapd for background reclaim.
This patch then converts a number of sites
o __GFP_ATOMIC is used by callers that are high priority and have memory
pools for those requests. GFP_ATOMIC uses this flag.
o Callers that have a limited mempool to guarantee forward progress clear
__GFP_DIRECT_RECLAIM but keep __GFP_KSWAPD_RECLAIM. bio allocations fall
into this category where kswapd will still be woken but atomic reserves
are not used as there is a one-entry mempool to guarantee progress.
o Callers that are checking if they are non-blocking should use the
helper gfpflags_allow_blocking() where possible. This is because
checking for __GFP_WAIT as was done historically now can trigger false
positives. Some exceptions like dm-crypt.c exist where the code intent
is clearer if __GFP_DIRECT_RECLAIM is used instead of the helper due to
flag manipulations.
o Callers that built their own GFP flags instead of starting with GFP_KERNEL
and friends now also need to specify __GFP_KSWAPD_RECLAIM.
The first key hazard to watch out for is callers that removed __GFP_WAIT
and was depending on access to atomic reserves for inconspicuous reasons.
In some cases it may be appropriate for them to use __GFP_HIGH.
The second key hazard is callers that assembled their own combination of
GFP flags instead of starting with something like GFP_KERNEL. They may
now wish to specify __GFP_KSWAPD_RECLAIM. It's almost certainly harmless
if it's missed in most cases as other activity will wake kswapd.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make pinning and waiting a separate step, and wait for object idle
without struct_mutex held.
Changes since v1:
- Do not wait when a reset is in progress.
- Remove call to i915_gem_object_wait_rendering for
intel_overlay_do_put_image (Chris Wilson)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
DRM_ERROR an continue without any issues aren't allowed since that
causes noise in the CI system. But we absolutely want to have the
DRM_ERROR when we want to run with GuC.
For simplicity just short-circuit all the loader code when it's not
needed.
v2: Mika&Chris complained that I shouldn't hit send on patches written
before coffee kicks in.
v3: Make it compile at least ...
Cc: Alex Dai <yu.dai@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445591459-4327-1-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Having flushed all requests from all queues, we know that all
ringbuffers must now be empty. However, since we do not reclaim
all space when retiring the request (to prevent HEADs colliding
with rapid ringbuffer wraparound) the amount of available space
on each ringbuffer upon reset is less than when we start. Do one
more pass over all the ringbuffers to reset the available space
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Grab execlist lock when cleaning up execlist queues after GPU reset to avoid
concurrency problems between the context event interrupt handler and the reset
path immediately following a GPU reset.
* v2 (Chris Wilson):
Do execlist check and use simpler form of spinlock functions.
Signed-off-by: Tomas Elf <tomas.elf@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Revision checks are almost always accompanied by a platform check. (The
exceptions are platform specific code.) Add helpers to check for a
platform and a revision range: IS_SKL_REVID() and IS_BXT_REVID(). In
most places this simplifies and clarifies the code. It will be obvious
that revid macros are used for the correct platform.
This should make it easier to find all the revision checks for
workarounds for each platform, and make it easier to remove them once we
drop support for early hardware revisions.
This should also make it easier to differentiate between Skylake and
Kabylake revision checks when Kabylake support is added.
v2: rebase
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445343722-3312-3-git-send-email-jani.nikula@intel.com
Since the remove of the pin-ioctl, we only care about not changing the
cache level on buffers pinned to the hardware as indicated by
obj->pin_display. By knowing that only objects pinned to the hardware
will have an elevated vma->pin_count, so we can coallesce many of the
linear walks over the obj->vma_list.
v2: Try and retrospectively add comments explaining the steps in
rebinding the active VMA.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prevent leaking VMAs and PPGTT VMs when objects are imported
via flink.
Scenario is that any VMAs created by the importer will be left
dangling after the importer exits, or destroys the PPGTT context
with which they are associated.
This is caused by object destruction not running when the
importer closes the buffer object handle due the reference held
by the exporter. This also leaks the VM since the VMA has a
reference on it.
In practice these leaks can be observed by stopping and starting
the X server on a kernel with fbcon compiled in. Every time
X server exits another VMA will be leaked against the fbcon's
frame buffer object.
Also on systems where flink buffer sharing is used extensively,
like Android, this leak has even more serious consequences.
This version is takes a general approach from the earlier work
by Rafael Barbalho (drm/i915: Clean-up PPGTT on context
destruction) and tries to incorporate the subsequent discussion
between Chris Wilson and Daniel Vetter.
v2:
Removed immediate cleanup on object retire - it was causing a
recursive VMA unbind via i915_gem_object_wait_rendering. And
it is in fact not even needed since by definition context
cleanup worker runs only after the last context reference has
been dropped, hence all VMAs against the VM belonging to the
context are already on the inactive list.
v3:
Previous version could deadlock since VMA unbind waits on any
rendering on an object to complete. Objects can be busy in a
different VM which would mean that the cleanup loop would do
the wait with the struct mutex held.
This is an even simpler approach where we just unbind VMAs
without waiting since we know all VMAs belonging to this VM
are idle, and there is nothing in flight, at the point
context destructor runs.
v4:
Double underscore prefix for __915_vma_unbind_no_wait and a
commit message typo fix. (Michel Thierry)
Note that this is just a partial/interim fix since we have a bit a
fundamental issue with cleaning up, e.g.
https://bugs.freedesktop.org/show_bug.cgi?id=87729
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Testcase: igt/gem_ppgtt.c/flink-and-exit-vma-leak
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rafael Barbalho <rafael.barbalho@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
[danvet: Add a note that this isn't everything.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are some allocations that must be only referenced by 32-bit
offsets. To limit the chances of having the first 4GB already full,
objects not requiring this workaround use DRM_MM_SEARCH_BELOW/
DRM_MM_CREATE_TOP flags
In specific, any resource used with flat/heapless (0x00000000-0xfffff000)
General State Heap (GSH) or Instruction State Heap (ISH) must be in a
32-bit range, because the General State Offset and Instruction State
Offset are limited to 32-bits.
Objects must have EXEC_OBJECT_SUPPORTS_48B_ADDRESS flag to indicate if
they can be allocated above the 32-bit address range. To limit the
chances of having the first 4GB already full, objects will use
DRM_MM_SEARCH_BELOW + DRM_MM_CREATE_TOP flags when possible.
The libdrm user of the EXEC_OBJECT_SUPPORTS_48B_ADDRESS flag is here:
http://lists.freedesktop.org/archives/intel-gfx/2015-September/075836.html
v2: Changed flag logic from neeeds_32b, to supports_48b.
v3: Moved 48-bit support flag back to exec_object. (Chris, Daniel)
v4: Split pin flags into PIN_ZONE_4G and PIN_HIGH; update PIN_OFFSET_MASK
to use last PIN_ defined instead of hard-coded value; use correct limit
check in eb_vma_misplaced. (Chris)
v5: Don't touch PIN_OFFSET_MASK and update workaround comment (Chris)
v6: Apply pin-high for ggtt too (Chris)
v7: Handle simultaneous pin-high and pin-mappable end correctly (Akash)
Fix check for entries currently using +4GB addresses, use min_t and
other polish in object_bind_to_vm (Chris)
v8: Commit message updated to point to libdrm patch.
v9: vmas are allocated in the correct ozone, so only check flag when the
vma has not been allocated. (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v4)
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge to catch up with 4.3. slightly more involved conflict in the
irq code, but nothing beyond adjacent changes.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
It would be initialized just moments later by i915_init_vm.
Rearrange the code such that i915_init_vm() is next to its callers
inside i915_gem_gtt (and so we can make it static). After removing the
dance around the files, it is clear that we are repeating some work
inside the initializers (such as calling drm_mm_init() multiple times),
so take advantage of the refactor to also remove some redundant code and
clean up the interface.
v2: Commit msg update,
s/i915_init_vm/i915_address_space_init, move to i915_gem_gtt.c,
init address_space during i915_gem_setup_global_gtt for ggtt.
v3: Do not init global_link - we are adding it to vm_list moments later,
make i915_address_space_init static, use OOP style parameter order.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the following 'make htmldocs' warnings:
.//drivers/gpu/drm/i915/i915_gem.c:1729: warning: No description found for parameter 'vma'
.//drivers/gpu/drm/i915/i915_gem.c:1729: warning: No description found for parameter 'vmf'
.//drivers/gpu/drm/i915/i915_gem.c:4962: warning: No description found for parameter 'old'
.//drivers/gpu/drm/i915/i915_gem.c:4962: warning: No description found for parameter 'new'
.//drivers/gpu/drm/i915/i915_gem.c:4962: warning: No description found for parameter 'frontbuffer_bits'
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Extend init/init_hw split to context init.
- Move context initialisation in to i915_gem_init_hw
- Move one off initialisation for render ring to
i915_gem_validate_context
- Move default context initialisation to logical_ring_init
Rename intel_lr_context_deferred_create to
intel_lr_context_deferred_alloc, to reflect reduced functionality &
alloc/init split.
This patch is intended to split out the allocation of resources &
initialisation to allow easier reuse of code for resume/gpu reset.
v2: Removed function ptr wrapping of do_switch_context (Daniel Vetter)
Left ->init_context int intel_lr_context_deferred_alloc
(Daniel Vetter)
Remove unnecessary init flag & ring type test. (Daniel Vetter)
Improve commit message (Daniel Vetter)
v3: On init/reinit, set the hw next sequence number to the sw next
sequence number. This is set to 1 at driver load time. This prevents
the seqno being reset on reinit (Chris Wilson)
v4: Set seqno back to ~0 - 0x1000 at start-of-day, and increment by 0x100
on reset.
This makes it obvious which bbs are which after a reset. (David Gordon
& John Harrison)
Rebase.
v5: Rebase. Fixed rebase breakage. Put context pinning in separate
function. Removed code churn. (Thomas Daniel)
v6: Cleanup up issues introduced in v2 & v5 (Thomas Daniel)
Issue: VIZ-4798
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: John Harrison <john.c.harrison@intel.com>
Cc: David Gordon <david.s.gordon@intel.com>
Cc: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This avoids some bad register writes and generally feels more correct
than unconditionally trying to redirect interrupts and such.
References: https://bugs.freedesktop.org/show_bug.cgi?id=91777
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Comment disagrees with the code which has changed a lot since
it was documented.
Note that the logic to remove -EIO handling was dropped in
commit 1488fc08c1
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Apr 24 15:47:31 2012 +0100
drm/i915: Remove the deferred-free list
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm updates from Dave Airlie:
"This is the main pull request for the drm for 4.3. Nouveau is
probably the biggest amount of changes in here, since it missed 4.2.
Highlights below, along with the usual bunch of fixes.
All stuff outside drm should have applicable acks.
Highlights:
- new drivers:
freescale dcu kms driver
- core:
more atomic fixes
disable some dri1 interfaces on kms drivers
drop fb panic handling, this was just getting more broken, as more locking was required.
new core fbdev Kconfig support - instead of each driver enable/disabling it
struct_mutex cleanups
- panel:
more new panels
cleanup Kconfig
- i915:
Skylake support enabled by default
legacy modesetting using atomic infrastructure
Skylake fixes
GEN9 workarounds
- amdgpu:
Fiji support
CGS support for amdgpu
Initial GPU scheduler - off by default
Lots of bug fixes and optimisations.
- radeon:
DP fixes
misc fixes
- amdkfd:
Add Carrizo support for amdkfd using amdgpu.
- nouveau:
long pending cleanup to complete driver,
fully bisectable which makes it larger,
perfmon work
more reclocking improvements
maxwell displayport fixes
- vmwgfx:
new DX device support, supports OpenGL 3.3
screen targets support
- mgag200:
G200eW support
G200e new revision support
- msm:
dragonboard 410c support, msm8x94 support, msm8x74v1 support
yuv format support
dma plane support
mdp5 rotation
initial hdcp
- sti:
atomic support
- exynos:
lots of cleanups
atomic modesetting/pageflipping support
render node support
- tegra:
tegra210 support (dc, dsi, dp/hdmi)
dpms with atomic modesetting support
- atmel:
support for 3 more atmel SoCs
new input formats, PRIME support.
- dwhdmi:
preparing to add audio support
- rockchip:
yuv plane support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1369 commits)
drm/amdgpu: rename gmc_v8_0_init_compute_vmid
drm/amdgpu: fix vce3 instance handling
drm/amdgpu: remove ib test for the second VCE Ring
drm/amdgpu: properly enable VM fault interrupts
drm/amdgpu: fix warning in scheduler
drm/amdgpu: fix buffer placement under memory pressure
drm/amdgpu/cz: fix cz_dpm_update_low_memory_pstate logic
drm/amdgpu: fix typo in dce11 watermark setup
drm/amdgpu: fix typo in dce10 watermark setup
drm/amdgpu: use top down allocation for non-CPU accessible vram
drm/amdgpu: be explicit about cpu vram access for driver BOs (v2)
drm/amdgpu: set MEC doorbell range for Fiji
drm/amdgpu: implement burst NOP for SDMA
drm/amdgpu: add insert_nop ring func and default implementation
drm/amdgpu: add amdgpu_get_sdma_instance helper function
drm/amdgpu: add AMDGPU_MAX_SDMA_INSTANCES
drm/amdgpu: add burst_nop flag for sdma
drm/amdgpu: add count field for the SDMA NOP packet v2
drm/amdgpu: use PT for VM sync on unmap
drm/amdgpu: make wait_event uninterruptible in push_job
...
Due to a coherency issue on BXT A steppings we can't guarantee a
coherent view of cached (CPU snooped) GPU mappings, so fail such
requests. User space is supposed to fall back to uncached mappings in
this case.
v2:
- limit the WA to A steppings, on later stepping this HW issue is fixed
v3:
- return error instead of trying to work around the issue in kernel,
since that could confuse user space (Chris)
Testcast: igt/gem_store_dword_batches_loop/cached-mapping
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fetches the required firmware image from the filesystem,
then loads it into the GuC's memory via a dedicated DMA engine.
This patch is derived from GuC loading work originally done by
Vinit Azad and Ben Widawsky.
v2:
Various improvements per review comments by Chris Wilson
v3:
Removed 'wait' parameter to intel_guc_ucode_load() as firmware
prefetch is no longer supported in the common firmware loader,
per Daniel Vetter's request.
Firmware checker callback fn now returns errno rather than bool.
v4:
Squash uC-independent code into GuC-specifc loader [Daniel Vetter]
Don't keep the driver working (by falling back to execlist mode)
if GuC firmware loading fails [Daniel Vetter]
v5:
Clarify WOPCM-related #defines [Tom O'Rourke]
Delete obsolete code no longer required with current h/w & f/w
[Tom O'Rourke]
Move the call to intel_guc_ucode_init() later, so that it can
allocate GEM objects, and have it fetch the firmware; then
intel_guc_ucode_load() doesn't need to fetch it later.
[Daniel Vetter].
v6:
Update comment describing intel_guc_ucode_load() [Tom O'Rourke]
Issue: VIZ-4884
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we don't clflush on pin_to_display if the bo is already
UC/WT and is not in the CPU write domain. This causes problems with
pwrite since pwrite doesn't change the write domain, and it avoids
clflushing on UC/WT buffers on LLC platforms unless the buffer is
currently being scanned out.
Fix the problem by marking the cache dirty and adjusting
i915_gem_object_set_cache_level() to clflush when the cache is dirty
even if the cache_level doesn't change.
My last attempt [1] at fixing this via write domain frobbing was shot
down, but now with the cache_dirty flag we can do things in a nicer way.
[1] http://lists.freedesktop.org/archives/intel-gfx/2014-November/055390.html
v2: Drop the I915_CACHE_NONE/WT checks from pwrite
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86422
Testcase: igt/kms_pwrite_crc
Testcase: igt/gem_pwrite_snooped
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similar to commit c44ef60e43 ("drm/i915/gtt:
Allow >= 4GB sizes for vm"), i915_gem_obj_offset and i915_gem_obj_ggtt_offset
return an unsigned long, which in only 4-bytes long in 32-bit kernels.
Change return type (and other related offset variables) to u64.
Since Global GTT is always limited to 4GB, this change would not be required
in i915_gem_obj_ggtt_offset, but this is done for consistency.
v2: Remove unnecessary offset variable in do_pin, as we already have
vma->node.start (Chris).
Update GGTT offset too (Tvrtko).
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In a 48b world, users can try to allocate buffers bigger than 4GB; in
these cases it is important that size is a 64b variable.
v2: Drop the warning about bind with size 0, it shouldn't happen anyway.
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we shrink our working sets, we want to avoid stealing pages from
objects that likely to be reused in the near future. We first look at
inactive objects before processing active objects - but what about a
recently active object that is about to be used again. That object's
position in the bound_list is ordered by the time of binding, not the
time of last use, so the most recently used inactive object could well
be at the head of the shrink list. To compensate, give the object a bump
to MRU when it becomes inactive (thus transitioning to the end of the
first pass in shrink lists). Conversely, bumping on inactive makes
bumping on active useless, since when we do have to reap from the active
working set, everything is going to become inactive very quickly and the
order pretty much random - just hope for the best at that point, as once
we start stalling on active objects, we can hope that the rebinding
neatly orders vital objects.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: Resolve merge conflict.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Replace the deprecated atomic_{set,clear}_mask() usage with the now
ubiquous atomic_{or,andnot}() functions.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
No code changes, just moving all the fence related code into a
separate file (and avoiding a bunch of forward declarations while at
it).
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
i915_gem_object_create_from_data() is a generic function to save data
from a plain linear buffer in a new pageable gem object that can later
be accessed by the CPU and/or GPU.
We will need this for the microcontroller firmware loading support code.
Derived from i915_gem_object_write(), originally by Alex Dai
v2:
Change of function: now allocates & fills a new object, rather than
writing to an existing object
New name courtesy of Chris Wilson
Explicit domain-setting and other improvements per review comments
by Chris Wilson & Daniel Vetter
v4:
Rebased
Issue: VIZ-4884
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge fixes since it's getting out of hand again with the massive
split due to atomic between -next and 4.2-rc. All the bugfixes in
4.2-rc are addressed already (by converting more towards atomic
instead of minimal duct-tape) so just always pick the version in next
for the conflicts in modeset code.
All the other conflicts are just adjacent lines changed.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_gem_gtt.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_drv.h
drivers/gpu/drm/i915/intel_ringbuffer.h
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
After the previous patch this flag will check always clear, as it's
never set for shmem backed and userptr objects, so we can remove it.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Yeah this isn't really fixes but it's a nice cleanup to
clarify the code but not really worth the hassle of backmerging. So
just add to -fixes, we're still early in -rc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have 3 types of DMA mappings for GEM objects:
1. physically contiguous for stolen and for objects needing contiguous
memory
2. DMA-buf mappings imported via a DMA-buf attach operation
3. SG DMA mappings for shmem backed and userptr objects
For 1. and 2. the lifetime of the DMA mapping matches the lifetime of the
corresponding backing pages and so in practice we create/release the
mapping in the object's get_pages/put_pages callback.
For 3. the lifetime of the mapping matches that of any existing GPU binding
of the object, so we'll create the mapping when the object is bound to
the first vma and release the mapping when the object is unbound from its
last vma.
Since the object can be bound to multiple vmas, we can end up creating a
new DMA mapping in the 3. case even if the object already had one. This
is not allowed by the DMA API and can lead to leaked mapping data and
IOMMU memory space starvation in certain cases. For example HW IOMMU
drivers (intel_iommu) allocate a new range from their memory space
whenever a mapping is created, silently overriding a pre-existing
mapping.
Fix this by moving the creation/removal of DMA mappings to the object's
get_pages/put_pages callbacks. These callbacks already check for and do
an early return in case of any nested calls. This way objects of the 3.
case also become more like the other object types.
I noticed this issue by enabling DMA debugging, which got disabled after
a while due to its internal mapping tables getting full. It also reported
errors in connection to random other drivers that did a DMA mapping for
an address that was previously mapped by i915 but was never released.
Besides these diagnostic messages and the memory space starvation
problem for IOMMUs, I'm not aware of this causing a real issue.
The fix is based on a patch from Chris.
v2:
- move the DMA mapping create/remove calls to the get_pages/put_pages
callbacks instead of adding new callbacks for these (Chris)
v3:
- also fix the get_page cache logic on the userptr async path (Chris)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The hang checker needs to inspect whether or not the ring request list is empty
as well as if the given engine has reached or passed the most recently
submitted request. The problem with this is that the hang checker cannot grab
the struct_mutex, which is required in order to safely inspect requests since
requests might be deallocated during inspection. In the past we've had kernel
panics due to this very unsynchronized access in the hang checker.
One solution to this problem is to not inspect the requests directly since
we're only interested in the seqno of the most recently submitted request - not
the request itself. Instead the seqno of the most recently submitted request is
stored separately, which the hang checker then inspects, circumventing the
issue of synchronization from the hang checker entirely.
This fixes a regression introduced in
commit 44cdd6d219
Author: John Harrison <John.C.Harrison@Intel.com>
Date: Mon Nov 24 18:49:40 2014 +0000
drm/i915: Convert 'ring_idle()' to use requests not seqnos
v2 (Chris Wilson):
- Pass current engine seqno to ring_idle() from i915_hangcheck_elapsed() rather
than compute it over again.
- Remove extra whitespace.
Issue: VIZ-5998
Signed-off-by: Tomas Elf <tomas.elf@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add regressing commit citation provided by Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be useful to PSR and FBC once we start making
dirty fb calls to also flush frontbuffer.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pass around requests to carry context deeper in callchain.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is found that i915 will not reset gpu under execlist mode when
unload module. that will lead to some issues when unload/load module
with different submission mode. e.g. from execlist mode to ring
buffer mode via loading/unloading i915. Because HW is not in a reset
state and registers are not clean under such condition.
Signed-off-by: Niu,Bing <bing.niu@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently only normal views were accounted which under-accounts
the usage as reported in debugfs.
Introduce new helper, i915_gem_obj_total_ggtt_size, and use it
from call sites which want to know how much GGTT space are
objects using.
v2: Single loop in i915_gem_get_aperture_ioctl. (Chris Wilson)
v3: Walk GGTT active/inactive lists in i915_gem_get_aperture_ioctl
for better efficiency. (Chris Wilson, Daniel Vetter)
v4: Make i915_gem_obj_total_ggtt_size private to debugfs. (Chris Wilson)
v5: Change unsigned long to u64. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can't elide the fb tracking invalidate if the buffer is already in
the right domain since that would lead to missed screen updates. I'm
pretty sure I've written this already before but must have gotten lost
unfortunately :(
v2: Chris observed that all internal set_domain users already
correctly do the fb invalidate on their own, hence we can move this
just into the set_domain ioctl instead.
v3: I screwed up setting the invalidate ORIGIN_* correctly (Chris).
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.2.
I've one other new driver from freescale on my radar, it's been posted
and reviewed, I'd just like to get someone to give it a last look, so
maybe I'll send it or maybe I'll leave it.
There is no major nouveau changes in here, Ben was working on
something big, and we agreed it was a bit late, there wasn't anything
else he considered urgent to merge.
There might be another msm pull for some bits that are waiting on
arm-soc, I'll see how we time it.
This touches some "of" stuff, acks are in place except for the fixes
to the build in various configs,t hat I just applied.
Summary:
New drivers:
- virtio-gpu:
KMS only pieces of driver for virtio-gpu in qemu.
This is just the first part of this driver, enough to run
unaccelerated userspace on. As qemu merges more we'll start
adding the 3D features for the virgl 3d work.
- amdgpu:
a new driver from AMD to driver their newer GPUs. (VI+)
It contains a new cleaner userspace API, and is a clean
break from radeon moving forward, that AMD are going to
concentrate on. It also contains a set of register headers
auto generated from AMD internal database.
core:
- atomic modesetting API completed, enabled by default now.
- Add support for mode_id blob to atomic ioctl to complete interface.
- bunch of Displayport MST fixes
- lots of misc fixes.
panel:
- new simple panels
- fix some long-standing build issues with bridge drivers
radeon:
- VCE1 support
- add a GPU reset counter for userspace
- lots of fixes.
amdkfd:
- H/W debugger support module
- static user-mode queues
- support killing all the waves when a process terminates
- use standard DECLARE_BITMAP
i915:
- Add Broxton support
- S3, rotation support for Skylake
- RPS booting tuning
- CPT modeset sequence fixes
- ns2501 dither support
- enable cmd parser on haswell
- cdclk handling fixes
- gen8 dynamic pte allocation
- lots of atomic conversion work
exynos:
- Add atomic modesetting support
- Add iommu support
- Consolidate drm driver initialization
- and MIC, DECON and MIPI-DSI support for exynos5433
omapdrm:
- atomic modesetting support (fixes lots of things in rewrite)
tegra:
- DP aux transaction fixes
- iommu support fix
msm:
- adreno a306 support
- various dsi bits
- various 64-bit fixes
- NV12MT support
rcar-du:
- atomic and misc fixes
sti:
- fix HDMI timing complaince
tilcdc:
- use drm component API to access tda998x driver
- fix module unloading
qxl:
- stability fixes"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (872 commits)
drm/nouveau: Pause between setting gpu to D3hot and cutting the power
drm/dp/mst: close deadlock in connector destruction.
drm: Always enable atomic API
drm/vgem: Set unique to "vgem"
of: fix a build error to of_graph_get_endpoint_by_regs function
drm/dp/mst: take lock around looking up the branch device on hpd irq
drm/dp/mst: make sure mst_primary mstb is valid in work function
of: add EXPORT_SYMBOL for of_graph_get_endpoint_by_regs
ARM: dts: rename the clock of MIPI DSI 'pll_clk' to 'sclk_mipi'
drm/atomic: Don't set crtc_state->enable manually
drm/exynos: dsi: do not set TE GPIO direction by input
drm/exynos: dsi: add support for MIC driver as a bridge
drm/exynos: dsi: add support for Exynos5433
drm/exynos: dsi: make use of array for clock access
drm/exynos: dsi: make use of driver data for static values
drm/exynos: dsi: add macros for register access
drm/exynos: dsi: rename pll_clk to sclk_clk
drm/exynos: mic: add MIC driver
of: add helper for getting endpoint node of specific identifiers
drm/exynos: add Exynos5433 decon driver
...
We can have exactly 4GB sized ppgtt with 32bit system.
size_t is inadequate for this.
v2: Convert a lot more places (Daniel)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As there is no OLR to check, the check_olr() function is now a no-op and can be
removed.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In _i915_add_request(), the request is associated with a userland client.
Specifically it is linked to the 'file' structure and the current user process
is recorded. One problem here is that the current user process is not
necessarily the same as when the request was submitted to the driver. This is
especially true when the GPU scheduler arrives and decouples driver submission
from hardware submission. Note also that it is only in the case where the add
request comes from an execbuff call that there is a client to associate. Any
other add request call is kernel only so does not need to do it.
This patch moves the client association into a separate function. This is then
called from the execbuffer code path itself at a sensible time. It also removes
the now redundant 'file' pointer from the add request parameter list.
An extra cleanup of the client association is also added to the request clean up
code for the eventuality where the request is killed after association but
before being submitted (e.g. due to out of memory error somewhere). Once the
submission has happened, the request is on the request list and the regular
request list removal will clear the association. Note that this still needs to
happen at this point in time because the request might be kept floating around
much longer (due to someone holding a reference count) and the client should not
be worrying about this request after it has been retired.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The outstanding_lazy_request is no longer used anywhere in the driver.
Everything that was looking at it now has a request explicitly passed in from on
high. Everything that was relying upon it behind the scenes is now explicitly
creating/passing/submitting its own private request. Thus the OLR can be
removed.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the *_ring_begin() functions no longer call the request allocation
code, it is finally safe for the request allocation code to call *_ring_begin().
This is important to guarantee that the space reserved for the subsequent
i915_add_request() call does actually get reserved.
v2: Renamed functions according to review feedback (Tomas Elf).
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that everything above has been converted to use requests, intel_ring_begin()
can be updated to take a request instead of a ring. This also means that it no
longer needs to lazily allocate a request if no-one happens to have done it
earlier.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Updated the ring->sync_to() implementations to take a request instead of a ring.
Also updated the tracer to include the request id.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
[danvet: Rebase since I didn't merge the patch which added ->uniq.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Updated the ring->emit_request() implementation to take a request instead of a
ringbuf/request pair. Also removed its use of the OLR for obtaining the
request's seqno.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Updated the various ring->add_request() implementations to take a request
instead of a ring. This removes their reliance on the OLR to obtain the seqno
value that the request should be tagged with.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Updated the *_ring_flush_all_caches() functions to take requests instead of
rings or ringbuf/context pairs.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Converted i915_gem_l3_remap() to take a request structure instead of a ring.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that everything above has been converted to use request structures, it is
possible to update the lower level move_to_active() functions to be request
based as well.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that all callers of i915_add_request() have a request pointer to hand, it is
possible to update the add request function to take a request pointer rather
than pulling it out of the OLR.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The plan is to pass requests around as the basic submission tracking structure
rather than rings and contexts. This patch updates the i915_gem_object_sync()
code path.
v2: Much more complex patch to share a single request between the sync and the
page flip. The _sync() function now supports lazy allocation of the request
structure. That is, if one is passed in then that will be used. If one is not,
then a request will be allocated and passed back out. Note that the _sync() code
does not necessarily require a request. Thus one will only be created until
certain situations. The reason the lazy allocation must be done within the
_sync() code itself is because the decision to need one or not is not really
something that code above can second guess (except in the case where one is
definitely not required because no ring is passed in).
The call chains above _sync() now support passing a request through which most
callers passing in NULL and assuming that no request will be required (because
they also pass in NULL for the ring and therefore can't be generating any ring
code).
The exeception is intel_crtc_page_flip() which now supports having a request
returned from _sync(). If one is, then that request is shared by the page flip
(if the page flip is of a type to need a request). If _sync() does not generate
a request but the page flip does need one, then the page flip path will create
its own request.
v3: Updated comment description to be clearer about 'to_req' parameter (Tomas
Elf review request). Rebased onto newer tree that significantly changed the
synchronisation code.
v4: Updated comments from review feedback (Tomas Elf)
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the request is guaranteed to specify the context, it is possible to
update the context switch code to use requests rather than ring and context
pairs. This patch updates i915_switch_context() accordingly.
Also removed the warning that the request's context must match the last context
switch's context. As the context switch now gets the context object from the
request structure, there is no longer any scope for the two to become out of
step.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The final step in removing the OLR from i915_gem_init_hw() is to pass the newly
allocated request structure in to each step rather than passing a ring
structure. This patch updates both i915_ppgtt_init_ring() and
i915_gem_context_enable() to take request pointers.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that a single per ring loop is being done for all the different
intialisation steps in i915_gem_init_hw(), it is possible to add proper request
management as well. The last remaining issue is that the context enable call
eventually ends up within *_render_state_init() and this does its own private
_i915_add_request() call.
This patch adds explicit request creation and submission to the top level loop
and removes the add_request() from deep within the sub-functions.
v2: Updated for removal of batch_obj from add_request call in previous patch.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The start of day context initialisation code in i915_gem_context_enable() loops
over each ring and calls the legacy switch context or the execlist init context
code as appropriate.
This patch moves the ring looping out of that function in to the top level
caller i915_gem_init_hw(). This means the a single pass can be made over all
rings doing the PPGTT, L3 remap and context initialisation of each ring
altogether.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The i915_gem_init_hw() function calls a bunch of smaller initialisation
functions. Multiple of which have generic sections and per ring sections. This
means multiple passes are done over the rings. Each pass writes data to the ring
which floats around in that ring's OLR until some random point in the future
when an add_request() is done by some random other piece of code.
This patch breaks i915_ppgtt_init_hw() in two with the per ring initialisation
now being done in i915_ppgtt_init_ring(). The ring looping is now done at the
top level in i915_gem_init_hw().
v2: Fix dumb loop variable re-use.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added explicit request creation and submission to the GPU idle code path.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In order to explcitly track all GPU work (and completely remove the outstanding
lazy request), it is necessary to add extra i915_add_request() calls to various
places. Some of these do not need the implicit cache flush done as part of the
standard batch buffer submission process.
This patch adds a flag to _add_request() to specify whether the flush is
required or not.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The alloc_request() function does not actually return the newly allocated
request. Instead, it must be pulled from ring->outstanding_lazy_request. This
patch fixes this so that code can create a request and start using it knowing
exactly which request it actually owns.
v2: Updated for new i915_gem_request_alloc() scheme.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In execlist mode, the context object pointer is written in to the request
structure (and reference counted) at the point of request creation. In legacy
mode, this only happens inside i915_add_request().
This patch updates the legacy code path to match the execlist version. This
allows all the intermediate code between request creation and request submission
to get at the context object given only a request structure. Thus negating the
need to pass context pointers here, there and everywhere.
v2: Moved the context reference so it does not need to be undone if the
get_seqno() fails.
v3: Fixed execlist mode always hitting a warning about invalid last_contexts
(which don't exist in execlist mode).
v4: Updated for new i915_gem_request_alloc() scheme.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The i915_add_request() function is called to keep track of work that has been
written to the ring buffer. It adds epilogue commands to track progress (seqno
updates and such), moves the request structure onto the right list and other
such house keeping tasks. However, the work itself has already been written to
the ring and will get executed whether or not the add request call succeeds. So
no matter what goes wrong, there isn't a whole lot of point in failing the call.
At the moment, this is fine(ish). If the add request does bail early on and not
do the housekeeping, the request will still float around in the
ring->outstanding_lazy_request field and be picked up next time. It means
multiple pieces of work will be tagged as the same request and driver can't
actually wait for the first piece of work until something else has been
submitted. But it all sort of hangs together.
This patch series is all about removing the OLR and guaranteeing that each piece
of work gets its own personal request. That means that there is no more
'hoovering up of forgotten requests'. If the request does not get tracked then
it will be leaked. Thus the add request call _must_ not fail. The previous patch
should have already ensured that it _will_ not fail by removing the potential
for running out of ring space. This patch enforces the rule by actually removing
the early exit paths and the return code.
Note that if something does manage to fail and the epilogue commands don't get
written to the ring, the driver will still hang together. The request will be
added to the tracking lists. And as in the old case, any subsequent work will
generate a new seqno which will suffice for marking the old one as complete.
v2: Improved WARNings (Tomas Elf review request).
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is a bad idea for i915_add_request() to fail. The work will already have been
send to the ring and will be processed, but there will not be any tracking or
management of that work.
The only way the add request call can fail is if it can't write its epilogue
commands to the ring (cache flushing, seqno updates, interrupt signalling). The
reasons for that are mostly down to running out of ring buffer space and the
problems associated with trying to get some more. This patch prevents that
situation from happening in the first place.
When a request is created, it marks sufficient space as reserved for the
epilogue commands. Thus guaranteeing that by the time the epilogue is written,
there will be plenty of space for it. Note that a ring_begin() call is required
to actually reserve the space (and do any potential waiting). However, that is
not currently done at request creation time. This is because the ring_begin()
code can allocate a request. Hence calling begin() from the request allocation
code would lead to infinite recursion! Later patches in this series remove the
need for begin() to do the allocate. At that point, it becomes safe for the
allocate to call begin() and really reserve the space.
Until then, there is a potential for insufficient space to be available at the
point of calling i915_add_request(). However, that would only be in the case
where the request was created and immediately submitted without ever calling
ring_begin() and adding any work to that request. Which should never happen. And
even if it does, and if that request happens to fall down the tiny window of
opportunity for failing due to being out of ring space then does it really
matter because the request wasn't doing anything in the first place?
v2: Updated the 'reserved space too small' warning to include the offending
sizes. Added a 'cancel' operation to clean up when a request is abandoned. Added
re-initialisation of tracking state after a buffer wrap to keep the sanity
checks accurate.
v3: Incremented the reserved size to accommodate Ironlake (after finally
managing to run on an ILK system). Also fixed missing wrap code in LRC mode.
v4: Added extra comment and removed duplicate WARN (feedback from Tomas).
For: VIZ-5115
CC: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge drm-next because the conflict between Ander's atomic fixes
for 4.2 and Maartens future work are getting to unwielding to handle.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_ringbuffer.h
Just always take ours, same as git merge -X ours, but done by hand
because I didn't trust git: It's confusing that it doesn't show any
conflicts in the merge diff at all.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This patch doesn't have any functional change, but organize fruntbuffer
invalidate and busy by removing unecesarry signature argument for ring.
It was unsed on mark_fb_busy and only used on fb_obj_invalidate for the
same ORIGIN_CS usage. So let's clean it a bit
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently we can have requests even if though the active list is empty,
so do the request retirement regardless of whether there's anything
on the active list.
The way it happened here is that during suspend intel_ring_idle()
notices the olr hanging around and then proceeds to get rid of it by
adding a request. However since there was nothing on the active lists
i915_gem_retire_requests() didn't clean those up, and so the idle work
never runs, and we leave the GPU "busy" during suspend resulting in a
WARN later.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
With the introduction of multiple views of an obj in the same vm, each
vma was taught to cache its copy of the pages (so that different views
could have different page arrangements). However, this missed decoupling
those vma->ggtt_view.pages when the vma released its reference on the
obj->pages. As we don't always free the vma, this leads to a possible
scenario (e.g. execbuffer interrupted by the shrinker) where the vma
points to a stale obj->pages, and explodes.
Fixes regression from commit fe14d5f4e5
Author: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Date: Wed Dec 10 17:27:58 2014 +0000
drm/i915: Infrastructure for supporting different GGTT views per object
Tvrtko says, if someone else will be confused how this can happen, key
is the reservation execbuffer path. That puts the VMA on the exec_list
which prevents i915_vma_unbind and i915_gem_vma_destroy from fully
destroying the VMA. So the VMA is left existing as an empty object in
the list - unbound and disassociated with the backing store. Kind of a
cached memory object. And then re-using it needs to clear the cached
pages pointer which is fixed above.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1227892
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
[Jani: Added Tvrtko's explanation to commit message.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Apparently we can have requests even if though the active list is empty,
so do the request retirement regardless of whether there's anything
on the active list.
The way it happened here is that during suspend intel_ring_idle()
notices the olr hanging around and then proceeds to get rid of it by
adding a request. However since there was nothing on the active lists
i915_gem_retire_requests() didn't clean those up, and so the idle work
never runs, and we leave the GPU "busy" during suspend resulting in a
WARN later.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In commit 1854d5ca0d
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Apr 7 16:20:32 2015 +0100
drm/i915: Deminish contribution of wait-boosting from clients
we removed an atomic timer based check for allowing waitboosting and
moved it below the mutex taken during RPS. However, that mutex can be
held for long periods of time on Vallyview/Cherryview as communication
with the PCU is slow. As clients may frequently wait for results (e.g.
such as tranform feedback) we introduced contention between the client
and the RPS worker. We can take advantage of the RPS worker, by
switching the wait boost decision to use spin locks and defer the
actual reclocking to the worker.
Fixes a regression of up to 45% on Baytrail and Baswell!
v2 (Daniel):
- Use max_freq_softlimit instead of the not-yet-merged boost
frequency.
- Don't inject a fake irq into the boost work, instead treat
client_boost as just another legit waker.
v3: Drop the now unused mask (Chris).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90112
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As Daniel commented on
commit b7ffe1362c5f468b853223acc9268804aa92afc8
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Apr 27 13:41:24 2015 +0100
drm/i915: Free RPS boosts for all laggards
it is better to be explicit when sharing hardcoded values such as
throttle/boost timeouts. Make it so!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After allocating from the slab cache, we then need to free the request
back into the slab cache upon error (and not call kfree as that leads
to eventual memory corruption).
Fixes regression from
commit efab6d8dd1
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Apr 7 16:20:57 2015 +0100
drm/i915: Use a separate slab for requests
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the client stalls on a congested request, chosen to be 20ms old to
match throttling, allow the client a free RPS boost.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
[danvet: s/0/NULL/ reported by 0-day build]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we have internal clients, rather than faking a whole
drm_i915_file_private just for tracking RPS boosts, create a new struct
intel_rps_client and pass it along when waiting.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ring switches can occur many times per frame, and are often out of
control, causing frequent RPS boosting for no practical benefit. Treat
the sw semaphore synchronisation as a separate client and only allow it
to boost once per busy/idle cycle.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently, we only track the last request globally across all engines.
This prevents us from issuing concurrent read requests on e.g. the RCS
and BCS engines (or more likely the render and media engines). Without
semaphores, we incur costly stalls as we synchronise between rings -
greatly impacting the current performance of Broadwell versus Haswell in
certain workloads (like video decode). With the introduction of
reference counted requests, it is much easier to track the last request
per ring, as well as the last global write request so that we can
optimise inter-engine read read requests (as well as better optimise
certain CPU waits).
v2: Fix inverted readonly condition for nonblocking waits.
v3: Handle non-continguous engine array after waits
v4: Rebase, tidy, rewrite ring list debugging
v5: Use obj->active as a bitfield, it looks cool
v6: Micro-optimise, mostly involving moving code around
v7: Fix retire-requests-upto for execlists (and multiple rq->ringbuf)
v8: Rebase
v9: Refactor i915_gem_object_sync() to allow the compiler to better
optimise it.
Benchmark: igt/gem_read_read_speed
hsw:gt3e (with semaphores):
Before: Time to read-read 1024k: 275.794µs
After: Time to read-read 1024k: 123.260µs
hsw:gt3e (w/o semaphores):
Before: Time to read-read 1024k: 230.433µs
After: Time to read-read 1024k: 124.593µs
bdw-u (w/o semaphores): Before After
Time to read-read 1x1: 26.274µs 10.350µs
Time to read-read 128x128: 40.097µs 21.366µs
Time to read-read 256x256: 77.087µs 42.608µs
Time to read-read 512x512: 281.999µs 181.155µs
Time to read-read 1024x1024: 1196.141µs 1118.223µs
Time to read-read 2048x2048: 5639.072µs 5225.837µs
Time to read-read 4096x4096: 22401.662µs 21137.067µs
Time to read-read 8192x8192: 89617.735µs 85637.681µs
Testcase: igt/gem_concurrent_blit (read-read and friends)
Cc: Lionel Landwerlin <lionel.g.landwerlin@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> [v8]
[danvet: s/\<rq\>/req/g]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The merged seqno->request conversion from John called request
variables req, but some (not all) of Chris' recent patches changed
those to just rq. We've had a lenghty (and inconclusive) discussion on
irc which is the more meaningful name with maybe at most a slight bias
towards req.
Given that the "don't change names without good reason to avoid
conflicts" rule applies, so lets go back to a req everywhere for
consistency. I'll sed any patches for which this will cause conflicts
before applying.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: John Harrison <John.C.Harrison@Intel.com>
[danvet: s/origina/merged/ as pointed out by Chris - the first
mass-conversion patch was from Chris, the merged one from John.]
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
We no longer interpolate domains in the same manner, and even if we did,
we should trust setting either of the other write domains would trigger
an invalidation rather than force it. Remove the tweaking of the
read_domains since it serves no purpose and use
i915_gem_object_wait_rendering() directly.
Note that this goes back to
commit a8198eea15
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Apr 13 22:04:09 2011 +0100
drm/i915: Introduce i915_gem_object_finish_gpu()
and gpu domain tracking died in
commit cc889e0f6c
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Jun 13 20:45:19 2012 +0200
drm/i915: disable flushing_list/gpu_write_list
which is more than 1 year older.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add notes with information dug out of git history.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We do not yet support tiled objects bigger than the mappable
aperture size so reject them.
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
[danvet: Rework the check a bit to avoid warnings.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use partial view for huge BOs (bigger than half the mappable aperture)
in fault handler so that they can be accessed withough trying to make
room for them by evicting other objects.
v2:
- Only use partial views in the case where early rejection was
previously done.
- Account variable type changes from previous reroll.
v3:
- Add a comment about overwriting existing page entries.
(Tvrtko Ursulin)
- Whitespace fixes.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Do not skip special GGTT views when considering whether an object
is pinned or not.
Wrong behaviour was introduced in;
commit ec7adb6ee7
Author: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Date: Mon Mar 16 14:11:13 2015 +0200
drm/i915: Do not use ggtt_view with (aliasing) PPGTT
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GGTT VMA sizes might be smaller than the whole object size due to
different GGTT views.
v2:
- Separate GGTT view constraint calculations from normal view
constraint calculations (Chris Wilson)
v3:
- Do not bother with debug wording. (Tvrtko Ursulin)
v4:
- Clearer logic for calculating map_and_fenceable (Tvrtko Ursulin)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
[danvet: Drop BUG_ON, it's redudant.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reading a single value from the object, the locking only provides futile
protection against userspace races. The locking is useless so remove it.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Unbinding doesn't always lead to unconditional destruction
of vma. This destruction avoidance happens if vma is part of
execbuffer relocation list or if vma is being considered for
eviction in i915_gem_evict_something().
For those other users, mark the vma unbound so that
the correct state of this vma is preserved.
Reported-by: Chris Wilson <chris@chris-wilson.co.ok>
Cc: Chris Wilson <chris@chris-wilson.co.ok>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-intel-next-2015-04-23:
- dither support for ns2501 dvo (Thomas Richter)
- some polish for the gtt code and fixes to finally enable the cmd parser on hsw
- first pile of bxt stage 1 enabling (too many different people to list ...)
- more psr fixes from Rodrigo
- skl rotation support from Chandra
- more atomic work from Ander and Matt
- pile of cleanups and micro-ops for execlist from Chris
drm-intel-next-2015-04-10:
- cdclk handling cleanup and fixes from Ville
- more prep patches for olr removal from John Harrison
- gmbus pin naming rework from Jani (prep for bxt)
- remove ->new_config from Ander (more atomic conversion work)
- rps (boost) tuning and unification with byt/bsw from Chris
- cmd parser batch bool tuning from Chris
- gen8 dynamic pte allocation (Michel Thierry, based on work from Ben Widawsky)
- execlist tuning (not yet all of it) from Chris
- add drm_plane_from_index (Chandra)
- various small things all over
* tag 'drm-intel-next-2015-04-23-fixed' of git://anongit.freedesktop.org/drm-intel: (204 commits)
drm/i915/gtt: Allocate va range only if vma is not bound
drm/i915: Enable cmd parser to do secure batch promotion for aliasing ppgtt
drm/i915: fix intel_prepare_ddi
drm/i915: factor out ddi_get_encoder_port
drm/i915/hdmi: check port in ibx_infoframe_enabled
drm/i915/hdmi: fix vlv infoframe port check
drm/i915: Silence compiler warning in dvo
drm/i915: Update DRIVER_DATE to 20150423
drm/i915: Enable dithering on NatSemi DVO2501 for Fujitsu S6010
rm/i915: Move i915_get_ggtt_vma_pages into ggtt_bind_vma
drm/i915: Don't try to outsmart gcc in i915_gem_gtt.c
drm/i915: Unduplicate i915_ggtt_unbind/bind_vma
drm/i915: Move ppgtt_bind/unbind around
drm/i915: move i915_gem_restore_gtt_mappings around
drm/i915: Fix up the vma aliasing ppgtt binding
drm/i915: Remove misleading comment around bind_to_vm
drm/i915: Don't use atomics for pg_dirty_rings
drm/i915: Don't look at pg_dirty_rings for aliasing ppgtt
drm/i915/skl: Support Y tiling in MMIO flips
drm/i915: Fixup kerneldoc for struct intel_context
...
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
WaIdleLiteRestore is an execlists-only workaround, and requires the driver
to ensure that any context always has HEAD!=TAIL when attempting lite
restore.
Add two extra MI_NOOP instructions at the end of each request, but keep
the requests tail pointing before the MI_NOOPs. We may not need to
executed them, and this is why request->tail is sampled before adding
these extra instructions.
If we submit a context to the ELSP which has previously been submitted,
move the tail pointer past the MI_NOOPs. This ensures HEAD!=TAIL.
v2: Move overallocation to gen8_emit_request, and added note about
sampling request->tail in commit message (Chris).
v3: Remove redundant request->tail assignment in __i915_add_request, in
lrc mode this is already set in execlists_context_queue.
Do not add wa implementation details inside gem (Chris).
v4: Apply the wa whenever the req has been resubmitted and update
comment (Chris).
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Currently we have the problem that the decision whether ptes need to
be (re)written is splattered all over the codebase. Move all that into
i915_vma_bind. This needs a few changes:
- Just reuse the PIN_* flags for i915_vma_bind and do the conversion
to vma->bound in there to avoid duplicating the conversion code all
over.
- We need to make binding for EXECBUF (i.e. pick aliasing ppgtt if
around) explicit, add PIN_USER for that.
- Two callers want to update ptes, give them a PIN_UPDATE for that.
Of course we still want to avoid double-binding, but that should be
taken care of:
- A ppgtt vma will only ever see PIN_USER, so no issue with
double-binding.
- A ggtt vma with aliasing ppgtt needs both types of binding, and we
track that properly now.
- A ggtt vma without aliasing ppgtt could be bound twice. In the
lower-level ->bind_vma functions hence unconditionally set
GLOBAL_BIND when writing the ggtt ptes.
There's still a bit room for cleanup, but that's for follow-up
patches.
v2: Fixup fumbles.
v3: s/PIN_EXECBUF/PIN_USER/ for clearer meaning, suggested by Chris.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
It's true that we might need to context switch, but both the signalling
and implementation of the same are a few source files away. Remove it.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They change with the address space and not with each vma, so move them
into the right pile of vfuncs. Save 2 pointers per vma and clarifies
the code.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Purpose of this tracking is to know when to flush the cache between
the CPU and the non-coherent display engine. Prior to:
commit 121920faf2
Author: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Date: Mon Mar 23 11:10:37 2015 +0000
drm/i915/skl: Query display address through a wrapper
This worked by a mix of direct flag manipulation and checking for
existence of a pinned GGTT VMA.
With the introduction of rotated display mappings this approach is
no longer correct.
New simpler approach is to just keep this count over calls which pin
and unpin objects to and from display, at the slight cost of extra
space in every bo.
(Inspired and extracted code from a larger rework by Chris Wilson.)
v2: Remove the limit since it is not well defined. (Chris Wilson, Ville Syrjälä)
v3: Commit message corrections. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
One month passed between posting a patch and it getting merged, and
unfortunately even though it still applies, it needs fixing to account
for changes in function parameters since:
commit d385612e15b8b6eb3db328d83f1872ef8a381788
Author: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Date: Tue Mar 17 14:45:29 2015 +0000
drm/i915: Log view type when printing warnings
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
[danvet: Squash in fixup from Tvrtko to fix the rebase conflict.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The obj->pin_mappable flag only exists for debug purposes and is a
hindrance that is mistreated with rotated GGTT views. For debug
purposes, it suffices to mark objects with pin_display as being of note.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This provides a nice boost to mesa in swap bound scenarios (as mesa
throttles itself to the previous frame and given the scenario that will
complete shortly). It will also provide a good boost to systems running
with semaphores disabled and so frequently waiting on the GPU as it
switches rings. In the most favourable of microbenchmarks, this can
increase performance by around 15% - though in practice improvements
will be marginal and rarely noticeable.
v2: Account for user timeouts
v3: Limit the spinning to a single jiffie (~1us) at most. On an
otherwise idle system, there is no scheduler contention and so without a
limit we would spin until the GPU is ready.
v4: Drop forcewake - the lazy coherent access doesn't require it, and we
have no reason to believe that the forcewake itself improves seqno
coherency - it only adds delay.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Eero Tamminen <eero.t.tamminen@intel.com>
Cc: "Rantala, Valtteri" <valtteri.rantala@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move to i915_vma_bind as it is part of the binding.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already assign a unique identifier to every request: seqno. That
someone felt like adding a second one without even mentioning why and
tweaking ABI smells very fishy.
Fixes regression from
commit b3a38998f0
Author: Nick Hoath <nicholas.hoath@intel.com>
Date: Thu Feb 19 16:30:47 2015 +0000
drm/i915: Fix a use after free, and unbalanced refcounting
v2: Rebase
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Nick Hoath <nicholas.hoath@intel.com>
Cc: Thomas Daniel <thomas.daniel@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
[danvet: Fixup because different merge order.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
vma are more frequently allocated than objects and so should equally
benefit from having a dedicated slab.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
requests are even more frequently allocated than objects and equally
benefit from having a dedicated slab.
v2: Rebase
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we submit a request to the GPU, we first take the rpm wakelock, and
only release it once the GPU has been idle for a small period of time
after all requests have been complete. This means that we are sure no
new interrupt can arrive whilst we do not hold the rpm wakelock and so
can drop the individual get/put around every single request inside
execlists.
Note: to close one potential issue we should mark the GPU as busy
earlier in __i915_add_request.
To elaborate: The issue is that we emit the irq signalling sequence
before we grab the rpm reference, which means we could miss the
resulting interrupt (since that's not set up when suspended). The only
bad side effect is a missed interrupt, gt mmio writes automatically
wake up the hw itself. But otoh we have an umbrella rpm reference for
the entirety of execbuf, as long as that's there we're covered.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Explain a bit more about the add_request issue, which after
some irc chatting with Chris turns out to not be an issue really.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now with the trimmed memcpy before the command parser, we try to
allocate many different sizes of batches, predominantly one or two
pages. We can therefore speed up searching for a good sized batch by
keeping the objects of buckets of roughly the same size.
v2: Add a comment about bucket sizes
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At runtime, this helps ensure that the batch pools are kept trim and
fast. Then at suspend, this releases memory that we do not need to
restore. It also ties into the oom-notifier to ensure that we recover as
much kernel memory as possible during OOM.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I woke up one morning and found 50k objects sitting in the batch pool
and every search seemed to iterate the entire list... Painting the
screen in oils would provide a more fluid display.
One issue with the current design is that we only check for retirements
on the current ring when preparing to submit a new batch. This means
that we can have thousands of "active" batches on another ring that we
have to walk over. The simplest way to avoid that is to split the pools
per ring and then our LRU execution ordering will also ensure that the
inactive buffers remain at the front.
v2: execlists still requires duplicate code.
v3: execlists requires more duplicate code
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit ec5cc0f9b0
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu Jun 12 10:28:55 2014 +0100
drm/i915: Restrict GPU boost to the RCS engine
The premise that media/blitter workloads are not affected by boosting is
patently false with a trip through igt. The question that remains is
what exactly is going wrong with the media workload that prompted this?
Hopefully that would be fixed by the missing agressive downclocking, in
addition to the extra restrictions imposed on how frequent a process is
allowed to boost.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Deepak S <deepak.s@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll>
Acked-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With boosting for missed pageflips, we have a much stronger indication
of when we need to (temporarily) boost GPU frequency to ensure smooth
delivery of frames. So now only allow each client to perform one RPS boost
in each period of GPU activity due to stalling on results.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The biggest user of i915_gem_object_get_page() is the relocation
processing during execbuffer. Typically userspace passes in a set of
relocations in sorted order. Sadly, we alternate between relocations
increasing from the start of the buffers, and relocations decreasing
from the end. However the majority of consecutive lookups will still be
in the same page. We could cache the start of the last sg chain, however
for most callers, the entire sgl is inside a single chain and so we see
no improve from the extra layer of caching.
v2: Avoid the double increment inside unlikely()
References: https://bugs.freedesktop.org/show_bug.cgi?id=88308
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The request allocation code is largely duplicated between legacy mode and
execlist mode. The actual difference between the two versions of the code is
pretty minimal.
This patch moves the common code out into a separate function. This is then
called by the execution specific version prior to setting up the one different
value.
For: VIZ-5190
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The submission portion of the execbuffer code path was abstracted into a
function pointer indirection as part of the legacy vs execlist work. The two
implementation functions are called 'i915_gem_ringbuffer_submission' and
'intel_execlists_submission' but the pointer was called 'do_execbuf'. There is
already a 'i915_gem_do_execbuffer' function (which is what calls the pointer
indirection). The name of the pointer is therefore considered to be backwards
and should be changed.
This patch renames it to 'execbuf_submit' which is hopefully a bit clearer.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We were missing a convenience stub to aquire the right mutex whilst
dropping the request, so add it.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVGHwjAAoJEHm+PkMAQRiG8rcIAJ6cEJ6mbqLpyz5XrGf4yNp0
+wG/QlEpT8rgrxe9wSjB3lfW3kR2Pe69b9fVVCdiklygdkmva5vfmDrVGGzYfe3M
QrFSSlMVBplvh6IiM/L1mVMtr3DSmCO23YZZ9R5b7FoEYatNHRpNWBCBpuXpd4aD
sLuIvO3L/S7LqeOAFkkYWv6AuL9umicmjR8u+nsmCSRJom7At/aJ6R66WIp9vxho
Rn7r6wcUk6B2Q/gYNjdSE8SIwdyKhuBGyvqQ9U9s6Btg9DQfM/b0vG5kw9hqeAq/
9445jqVDP1whA2vz6GjnvltidxrqRvuDPBwzOnFmY5U+KZz4lS3x2mnWAAJ3xWs=
=TqVJ
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rc6' into drm-intel-next
Backmerge Linux 4.0-rc6 because conflicts are (again) getting out of
hand. To make sure we don't lose any bugfixes from the 4.0-rc5-rc6
flurry of patches we've applied them all to -next too.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Always take the version from -next, we've already handled all
conflicts with explicit cherrypicking.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
To allow for views where the view type is not defined by the view type only,
like it is in stereo or rotated 90 degree view, change the semantic to require
the whole view structure for comparison when we match a GGTT view.
This allows including parameters like offset to be included in the view which
is useful for eg. partial views.
v3:
- Rely on ggtt_view type being 0 for non-GGTT vma's, which equals to
I915_GGTT_VIEW_NORMAL. (Daniel Vetter)
- Do not use potentially slower comparison when we only want to know if
something is or is not a normal view.
- Rebase on top of rotated view patches. Add rotated view singleton.
- If one view is missing in comparison they're equal only if both are missing.
v4:
- Use comparison helper in obj_to_ggtt_view too. (Tvrtko Ursulin)
- Do WARN_ON if one view is NULL. (Tvrtko Ursulin)
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Traces for page directories and tables allocation and map.
v2: Removed references to teardown.
v3: bitmap_scnprintf has been deprecated.
v4: Replace bitmap_scnprintf with scnprintf correctly, and get right
range lengths. (Mika)
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we retire requests last, we may use a later seqno and so clear
the requests lists without clearing the active list, leading to
confusion. Hence we should retire requests first for consistency with
the early return. The order used to be important as the lifecycle for
the object on the active list was determined by request->seqno. However,
the requests themselves are now reference counted removing the
constraint from the order of retirement.
Fixes regression from
commit 1b5a433a4d
Author: John Harrison <John.C.Harrison@Intel.com>
Date: Mon Nov 24 18:49:42 2014 +0000
drm/i915: Convert 'i915_seqno_passed' calls into 'i915_gem_request_completed
'
and a
WARNING: CPU: 0 PID: 1383 at drivers/gpu/drm/i915/i915_gem_evict.c:279 i915_gem_evict_vm+0x10c/0x140()
WARN_ON(!list_empty(&vm->active_list))
Identified by updating WATCH_LISTS:
[drm:i915_verify_lists] *ERROR* blitter ring: active list not empty, but no requests
WARNING: CPU: 0 PID: 681 at drivers/gpu/drm/i915/i915_gem.c:2751 i915_gem_retire_requests_ring+0x149/0x230()
WARN_ON(i915_verify_lists(ring->dev))
Note that this is only a problem in evict_vm where the following happens
after a retire_request has cleaned out all requests, but not all active
bo:
- intel_ring_idle called from i915_gpu_idle notices that no requests are
outstanding and immediately returns.
- i915_gem_retire_requests_ring called from i915_gem_retire_requests also
immediately returns when there's no request, still leaving the bo on the
active list.
- evict_vm hits the WARN_ON(!list_empty(&vm->active_list)) after evicting
all active objects that there's still stuff left that shouldn't be
there.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
90/270 rotated scanout needs a rotated GTT view of the framebuffer.
This is put in a separate VMA with a dedicated ggtt view and wired such that
it is created when a framebuffer is pinned to a 90/270 rotated plane.
Rotation is only possible with Yb/Yf buffers and error is propagated to
user space in case of a mismatch.
Special rotated page view is constructed at the VMA creation time by
borrowing the DMA addresses from obj->pages.
v2:
* Do not bother with pages for rotated sg list, just populate the DMA
addresses. (Daniel Vetter)
* Checkpatch cleanup.
v3:
* Rebased on top of new plane handling (create rotated mapping when
setting the rotation property).
* Unpin rotated VMA on unpinning from display plane.
* Simplify rotation check using bitwise AND. (Chris Wilson)
v4:
* Fix unpinning of optional rotated mapping so it is really considered
to be optional.
v5:
* Rebased for fb modifier changes.
* Rebased for atomic commit.
* Only pin needed view for display. (Ville Syrjälä, Daniel Vetter)
v6:
* Rebased after preparatory work has been extracted out. (Daniel Vetter)
v7:
* Slightly simplified tiling geometry calculation.
* Moved rotated GGTT view implementation into i915_gem_gtt.c (Daniel Vetter)
v8:
* Do not use i915_gem_obj_size to get object size since that actually
returns the size of an VMA which may not exist.
* Rebased for ggtt view changes.
v9:
* Rebased after code review changes on the preceding patches.
* Tidy function definitions. (Joonas Lahtinen)
For: VIZ-4726
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> (v4)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To support frame buffer rotation we need to be able to pass on the information
on what kind of GGTT view is required for display.
This patch just adds the parameter and makes all the callers default to the
normal view.
v2: Rebased for ggtt view changes.
v3: Don't limit PIN_MAPPABLE to normal views just yet. (Joonas Lahtinen)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> (v3)
[danvet: s/BUG/WARN/ in the patch hunk because. At least where the
BUG_ON isn't fatal right away.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch was formerly known as, "Force pd restore when PDEs change,
gen6-7." I had to change the name because it is needed for GEN8 too.
The real issue this is trying to solve is when a new object is mapped
into the current address space. The GPU does not snoop the new mapping
so we must do the gen specific action to reload the page tables.
GEN8 and GEN7 do differ in the way they load page tables for the RCS.
GEN8 does so with the context restore, while GEN7 requires the proper
load commands in the command streamer. Non-render is similar for both.
Caveat for GEN7
The docs say you cannot change the PDEs of a currently running context.
We never map new PDEs of a running context, and expect them to be
present - so I think this is okay. (We can unmap, but this should also
be okay since we only unmap unreferenced objects that the GPU shouldn't
be tryingto va->pa xlate.) The MI_SET_CONTEXT command does have a flag
to signal that even if the context is the same, force a reload. It's
unclear exactly what this does, but I have a hunch it's the right thing
to do.
The logic assumes that we always emit a context switch after mapping new
PDEs, and before we submit a batch. This is the case today, and has been
the case since the inception of hardware contexts. A note in the comment
let's the user know.
It's not just for gen8. If the current context has mappings change, we
need a context reload to switch
v2: Rebased after ppgtt clean up patches. Split the warning for aliasing
and true ppgtt options. And do not break aliasing ppgtt, where to->ppgtt
is always null.
v3: Invalidate PPGTT TLBs inside alloc_va_range.
v4: Rename ppgtt_invalidate_tlbs to mark_tlbs_dirty and move
pd_dirty_rings from i915_address_space to i915_hw_ppgtt. Fixes when
neither ctx->ppgtt and aliasing_ppgtt exist.
v5: Removed references to teardown_va_range.
v6: Updated needs_pd_load_pre/post.
v7: Fix pd_dirty_rings check in needs_pd_load_post, and update/move
comment about updated PDEs to object_pin/bind (Mika).
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com> (v2+)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of implementing the full tracking + dynamic allocation, this
patch does a bit less than half of the work, by tracking and warning on
unexpected conditions. The tracking itself follows which PTEs within a
page table are currently being used for objects. The next patch will
modify this to actually allocate the page tables only when necessary.
With the current patch there isn't much in the way of making a gen
agnostic range allocation function. However, in the next patch we'll add
more specificity which makes having separate functions a bit easier to
manage.
One important change introduced here is that DMA mappings are
created/destroyed at the same page directories/tables are
allocated/deallocated.
Notice that aliasing PPGTT is not managed here. The patch which actually
begins dynamic allocation/teardown explains the reasoning for this.
v2: s/pdp.page_directory/pdp.page_directories
Make a scratch page allocation helper
v3: Rebase and expand commit message.
v4: Allocate required pagetables only when it is needed, _bind_to_vm
instead of bind_vma (Daniel).
v5: Rebased to remove the unnecessary noise in the diff, also:
- PDE mask is GEN agnostic, renamed GEN6_PDE_MASK to I915_PDE_MASK.
- Removed unnecessary checks in gen6_alloc_va_range.
- Changed map/unmap_px_single macros to use dma functions directly and
be part of a static inline function instead.
- Moved drm_device plumbing through page tables operation to its own
patch.
- Moved allocate/teardown_va_range calls until they are fully
implemented (in subsequent patch).
- Merged pt and scratch_pt unmap_and_free path.
- Moved scratch page allocator helper to the patch that will use it.
v6: Reduce complexity by not tearing down pagetables dynamically, the
same can be achieved while freeing empty vms. (Daniel)
v7: s/i915_dma_map_px_single/i915_dma_map_single
s/gen6_write_pdes/gen6_write_pde
Prevent a NULL case when only GGTT is available. (Mika)
v8: Rebased after s/page_tables/page_table/.
v9: Reworked i915_pte_index and i915_pte_count.
Also exercise bitmap allocation here (gen6_alloc_va_range) and fix
incorrect write_page_range in i915_gem_restore_gtt_mappings (Mika).
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com> (v3+)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Two code changes:
- Extract i915_gem_shrinker_init.
- Inline i915_gem_object_is_purgeable since we open-code it everywhere
else too.
This already has the benefit of pulling all the shrinker code
together, next patch adds a bit of kerneldoc.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This makes the interface consistent to old i915_gem_obj_ggtt_pin.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GGTT views are only applicable when dealing with GGTT. Change the code to
reject ggtt_view where it should not be used and require it when it should
be.
v2:
- Dropped _ppgtt_ infixes, allow both types to be passed
- Disregard other but normal views when no view is specified
- More checks that valid parameters are passed
- More readable error checking
v3:
- Prefer WARN_ONCE over BUG_ON when there is code path for failure
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
[danvet: Drop unecessary forward decl from earlier patch iterations.]
[danvet: Remove unused variable spotted by Tvrtko.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge because of numerous and interleaving conflicts and git
rerere getting confused a bit too often.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
All conflicts are because of -next patches backported to -fixes, so
just go with the code in -next.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
We need this for FBC, and possibly for PSR too.
v2: Don't only flush: invalidate too (Daniel).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to port FBC to the frontbuffer tracking infrastructure, but
for that we need to know what caused the object invalidation so
we can react accordingly: CPU mmaps need manual, GTT mmaps and
flips don't need handling and ring rendering needs nukes.
v2: - s/ORIGIN_RENDER/ORIGIN_CS/ (Daniel, Rodrigo)
- Fix copy/pasted wrong documentation
- Rebase
v3: - Rebase
v4: - Don't pass the operation to flushes (Daniel).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Long ago I found that I was getting sporadic errors when booting SNB,
with the symptom being that the first batch died with IPEHR != *ACTHD,
typically caused by the TLB being invalid. These magically disappeared
if I held the forcewake during the entire ring initialisation sequence.
(It can probably be shortened to a short critical section, but the whole
initialisation is full of register writes and so we would be taking and
releasing forcewake almost continually, and so holding it over the
entire sequence will probably be a net win!)
Note some of the kernels I encounted the issue already had the deferred
forcewake release, so it is still relevant.
I know that there have been a few other reports with similar failure
conditions on SNB, I think such as
References: https://bugs.freedesktop.org/show_bug.cgi?id=80913
v2: Wrap i915_gem_init_hw() with its own security blanket as we take
that path following resume and reset.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This fixes a regression from
commit 5ed0bdf21a
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Wed Jul 16 21:05:06 2014 +0000
drm: i915: Use nsec based interfaces
that made a negative timeout return immediately rather than the
previously defined behaviour of waiting indefinitely.
Testcase: igt/gem_wait
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89494
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Kristian Høgsberg <krh@bitplanet.net>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Jani: fixed a checkpatch complaint about whitespace.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU/NacAAoJEHm+PkMAQRiGdUcIAJU5dHclwd9HRc7LX5iOwYN6
mN0aCsYjMD8Pjx2VcPCgJvkIoESQO5pkwYpFFWCwILup1bVEidqXfr8EPOdThzdh
kcaT0FwUvd19K+0jcKVNCX1RjKBtlUfUKONk6sS2x4RrYZpv0Ur8Gh+yXV8iMWtf
fAusNEYlxQJvEz5+NSKw86EZTr4VVcykKLNvj+/t/JrXEuue7IG8EyoAO/nLmNd2
V/TUKKttqpE6aUVBiBDmcMQl2SUVAfp5e+KJAHmizdDpSE80nU59UC1uyV8VCYdM
qwHXgttLhhKr8jBPOkvUxl4aSXW7S0QWO8TrMpNdEOeB3ZB8AKsiIuhe1JrK0ro=
=Xkue
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rc3' into drm-next
Linux 4.0-rc3 backmerge to fix two i915 conflicts, and get
some mainline bug fixes needed for my testing box
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/intel_display.c
- Y tiling support for scanout from Tvrtko&Damien
- Remove more UMS support
- some small prep patches for OLR removal from John Harrison
- first few patches for dynamic pagetable allocation from Ben Widawsky, rebased
by tons of other people
- DRRS support patches (Sonika&Vandana)
- fbc patches from Paulo
- make sure our vblank callbacks aren't called when the pipes are off
- various patches all over
* tag 'drm-intel-next-2015-02-27' of git://anongit.freedesktop.org/drm-intel: (61 commits)
drm/i915: Update DRIVER_DATE to 20150227
drm/i915: Clarify obj->map_and_fenceable
drm/i915/skl: Allow Y (and Yf) frame buffer creation
drm/i915/skl: Update watermarks for Y tiling
drm/i915/skl: Updated watermark programming
drm/i915/skl: Adjust get_plane_config() to support Yb/Yf tiling
drm/i915/skl: Teach pin_and_fence_fb_obj() about Y tiling constraints
drm/i915/skl: Adjust intel_fb_align_height() for Yb/Yf tiling
drm/i915/skl: Allow scanning out Y and Yf fbs
drm/i915/skl: Add new displayable tiling formats
drm/i915: Remove DRIVER_MODESET checks from modeset code
drm/i915: Remove regfile code&data for UMS suspend/resume
drm/i915: Remove DRIVER_MODESET checks from gem code
drm/i915: Remove DRIVER_MODESET checks in the gpu reset code
drm/i915: Remove DRIVER_MODESET checks from suspend/resume code
drm/i915: Remove DRIVER_MODESET checks in load/unload/close code
drm/i915: fix a printk format
drm/i915: Add media rc6 residency file to sysfs
drm/i915: Add missing description to parameter in alloc_pt_range
drm/i915: Removed the read of RP_STATE_CAP from sysfs/debugfs functions
...
- use the atomic helpers for plane_upate/disable hooks (Matt Roper)
- refactor the initial plane config code (Damien)
- ppgtt prep patches for dynamic pagetable alloc (Ben Widawsky, reworked and
rebased by a lot of other people)
- framebuffer modifier support from Tvrtko Ursulin, drm core code from Rob Clark
- piles of workaround patches for skl from Damien and Nick Hoath
- vGPU support for xengt on the client side (Yu Zhang)
- and the usual smaller things all over
* tag 'drm-intel-next-2015-02-14' of git://anongit.freedesktop.org/drm-intel: (88 commits)
drm/i915: Update DRIVER_DATE to 20150214
drm/i915: Remove references to previously removed UMS config option
drm/i915/skl: Use a LRI for WaDisableDgMirrorFixInHalfSliceChicken5
drm/i915/skl: Fix always true comparison in a revision id check
drm/i915/skl: Implement WaEnableLbsSlaRetryTimerDecrement
drm/i915/skl: Implement WaSetDisablePixMaskCammingAndRhwoInCommonSliceChicken
drm/i915: Add process identifier to requests
drm/i915/skl: Implement WaBarrierPerformanceFixDisable
drm/i915/skl: Implement WaCcsTlbPrefetchDisable:skl
drm/i915/skl: Implement WaDisableChickenBitTSGBarrierAckForFFSliceCS
drm/i915/skl: Implement WaDisableHDCInvalidation
drm/i915/skl: Implement WaDisableLSQCROPERFforOCL
drm/i915/skl: Implement WaDisablePartialResolveInVc
drm/i915/skl: Introduce a SKL specific init_workarounds()
drm/i915/skl: Document that we implement WaRsClearFWBitsAtReset
drm/i915/skl: Implement WaSetGAPSunitClckGateDisable
drm/i915/skl: Make the init clock gating function skylake specific
drm/i915/skl: Provide a gen9 specific init_render_ring()
drm/i915/skl: Document the WM read latency W/A with its name
drm/i915/skl: Also detect eDRAM on SKL
...
For an object right on the boundary of mappable space, as the fenceable
size is stricly greater than the actual size, its fence region may extend
out of mappable space.
Note that only pnv/g33 has fence_size > obj.size and an unmappable
range in the gtt, and there alignment constraints prevent bad things
from happening.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Clarify why this shouldn't change anything as per the
discussion on intel-gfx.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In execlist mode, the ringbuf is a function of the ring and context whereas in
legacy mode, it is derived from the ring alone. Thus the calculation required to
determine the ringbuf pointer from the ring (and context) also needs to test
execlist mode or not. This is messy.
Further, the request structure holds a pointer to both the ring and the context
for which it was created. Thus, given a request, it is possible to derive the
ringbuf in either legacy or execlist mode. Hence it is necessary to pass just
the request in to all the low level functions rather than some combination of
request, ring, context and ringbuf. However, rather than recalculating it each
time, it is much simpler to just cache the ringbuf pointer in the request
structure itself.
Caching the pointer means the calculation is done once at request creation time
and all further code and simply read it directly from the request structure.
OTC-Jira: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
[danvet: Drop contentless comment in lrc alloc request entirely. And
spelling fix in the commit message.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When converting from implicitly tracked execlist queue items to ref counted
requests, not all frees of requests were replaced with unrefs, and extraneous
refs/unrefs of contexts were added.
Correct the unbalanced refcount & replace the frees.
Remove a noisy warning when hitting the request creation path.
drm_i915_gem_request and intel_context are both kref reference counted
structures. Upon allocation, drm_i915_gem_request's ref count should be
bumped using kref_init. When a context is assigned to the request,
the context's reference count should be bumped using i915_gem_context_reference.
i915_gem_request_reference will reduce the context reference count when
the request is freed.
Problem introduced in
commit 6d3d8274bc
Author: Nick Hoath <nicholas.hoath@intel.com>
AuthorDate: Thu Jan 15 13:10:39 2015 +0000
drm/i915: Subsume intel_ctx_submit_request in to drm_i915_gem_request
v2: Added comments explaining how the ctx pointer and the request object should
be ref-counted. Removed noisy warning.
v3: Cleaned up the language used in the commit & the header
description (Thanks David Gordon)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88652
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Chris Wilson