The cached command status is only set when the write back status is
is passed in. Move the variable set outside of the check so it is
always set.
Fixes: 0d5c10b4c8 ("dmaengine: idxd: add work queue drain support")
Reported-by: Ramesh Thomas <ramesh.thomas@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/162274329740.1822314.3443875665504707588.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add occupancy information to wq sysfs attribute. Attribute will show
wq occupancy data if "WQ Occupancy Support" field in WQCAP is 1. It
displays the number of entries currently in this WQ. This is provided
as an estimate and should not be relied on to determine whether there
is space in the WQ. The data is to provide information to user apps
for flow control.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/162275745546.1857062.8765615879420582018.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The previous state cleanup patch only performed wq state cleanups. This
does not go far enough as when device is disabled or reset, the state
for groups and engines must also be cleaned up. Add additional state
cleanup beyond wq cleanup. Tie those cleanups directly to device
disable and reset, and wq disable and reset.
Fixes: da32b28c95 ("dmaengine: idxd: cleanup workqueue config after disabling")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/162285154108.2096632.5572805472362321307.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by moving the error_pm label above the pm_runtime_put() in
the error path.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20210706124521.1371901-1-yukuai3@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When user calls dmaengine_terminate_sync, the driver will clean up any
remaining descriptors for all the pending or active transfers that had
previously been submitted. However, this might happen whilst the tasklet is
invoking the DMA callback for the last finished transfer, so by the time it
returns and takes over the channel's spinlock, the list of completed
descriptors it was traversing is no longer valid. This leads to a
read-after-free situation.
Fix it by signalling whether a user-triggered termination has happened by
means of a boolean variable.
Signed-off-by: Adrian Larumbe <adrian.martinezlarumbe@imgtec.com>
Link: https://lore.kernel.org/r/20210706234338.7696-3-adrian.martinezlarumbe@imgtec.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The wrappers in include/linux/pci-dma-compat.h should go away.
Replace 'pci_set_dma_mask/pci_set_consistent_dma_mask' by an equivalent
and less verbose 'dma_set_mask_and_coherent()' call.
Even if the code may look different, it should have exactly the same
run-time behavior.
If pci_set_dma_mask(64) fails and pci_set_dma_mask(32) succeeds, then
pci_set_consistent_dma_mask(64) will also fail.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/70c8a3bc67e41c5fefb526ecd64c5174c1e2dc76.1625720835.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Intel Elkhart Lake PSE DMA implementation is integrated with crossbar IP
in order to serve more hardware than there are DMA request lines available.
Due to this, program xBAR hardware to make flexible support of PSE peripheral.
The Device-to-Device has not been tested and it's not supported by DMA Engine,
but it's left in the code for the sake of documenting hardware features.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210712113940.42753-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix the following fallthrough warning:
drivers/dma/ti/k3-udma.c:4951:2: warning: unannotated fall-through between switch labels [-Wimplicit-fallthrough]
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Fix the following fallthrough warnings (arm64-randconfig):
drivers/dma/ipu/ipu_idmac.c:621:2: warning: unannotated fall-through between switch labels [-Wimplicit-fallthrough]
rivers/dma/ipu/ipu_idmac.c:981:2: warning: unannotated fall-through between switch labels [-Wimplicit-fallthrough]
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/60edca25.k00ut905IFBjPyt5%25lkp@intel.com/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Here is the small set of driver core and debugfs updates for 5.14-rc1.
Included in here are:
- debugfs api cleanups (touched some drivers)
- devres updates
- tiny driver core updates and tweaks
Nothing major in here at all, and all have been in linux-next for a
while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM7jA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yloDQCfZOlLYXF+2KgXJQqevNnRiu7/B1gAn3aCX6xh
UWVUfu5LDIXi2uFERRT1
=Ze3R
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core changes from Greg KH:
"Here is the small set of driver core and debugfs updates for 5.14-rc1.
Included in here are:
- debugfs api cleanups (touched some drivers)
- devres updates
- tiny driver core updates and tweaks
Nothing major in here at all, and all have been in linux-next for a
while with no reported issues"
* tag 'driver-core-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (27 commits)
docs: ABI: testing: sysfs-firmware-memmap: add some memmap types.
devres: Enable trace events
devres: No need to call remove_nodes() when there none present
devres: Use list_for_each_safe_from() in remove_nodes()
devres: Make locking straight forward in release_nodes()
kernfs: move revalidate to be near lookup
drivers/base: Constify static attribute_group structs
firmware_loader: remove unneeded 'comma' macro
devcoredump: remove contact information
driver core: Drop helper devm_platform_ioremap_resource_wc()
component: Rename 'dev' to 'parent'
component: Drop 'dev' argument to component_match_realloc()
device property: Don't check for NULL twice in the loops
driver core: auxiliary bus: Fix typo in the docs
drivers/base/node.c: make CACHE_ATTR define static DEVICE_ATTR_RO
debugfs: remove return value of debugfs_create_ulong()
debugfs: remove return value of debugfs_create_bool()
scsi: snic: debugfs: remove local storage of debugfs files
b43: don't save dentries for debugfs
b43legacy: don't save dentries for debugfs
...
New drivers/devices
- Support for QCOM SM8250 GPI DMA
- removal of shdma-of driver and binding
Updates:
- arm-pl08x yaml binding move
- altera-msgdma gained DT support
- removal of imx-sdma platform data support
- idxd and xilinx driver updates
-----BEGIN PGP SIGNATURE-----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=yltL
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"This time around we have a smaller pull request than usual and this
includes code removal, so should be good!
New drivers/devices
- Support for QCOM SM8250 GPI DMA
- removal of shdma-of driver and binding
Updates:
- arm-pl08x yaml binding move
- altera-msgdma gained DT support
- removal of imx-sdma platform data support
- idxd and xilinx driver updates"
* tag 'dmaengine-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (22 commits)
dmaengine: imx-sdma: Remove platform data header
dmaengine: xilinx: dpdma: Fix spacing around addr[i-1]
dmaengine: xilinx: dpdma: Use kernel type u32 over uint32_t
dmaengine: altera-msgdma: add OF support
MAINTAINERS: add entry for Altera mSGDMA
dt-bindings: dma: add schema for altera-msgdma
dmaengine: xilinx: dpdma: fix kernel-doc
dmaengine: sf-pdma: apply proper spinlock flags in sf_pdma_prep_dma_memcpy()
dmaengine: sh: Remove unused shdma-of driver
dt-bindings: dmaengine: Remove SHDMA Device Tree bindings
dmaengine: qcom: gpi: Add SM8250 compatible
dt-bindings: dmaengine: qcom: gpi: add compatible for sm8250
dmaengine: sun4i: Use list_move_tail instead of list_del/list_add_tail
dmaengine: ti: omap-dma: Skip pointless cpu_pm context restore on errors
dmaengine: hsu: Account transferred bytes
dmaengine: Move kdoc description of struct dma_chan_percpu closer to it
dmaengine: xilinx: dpdma: Print debug message when losing vsync race
dmaengine: xilinx: dpdma: Print channel number in kernel log messages
dt-bindings: dma: convert arm-pl08x to yaml
dmaengine: idxd: remove devm allocation for idxd->int_handles
...
Since commit 6c5f05a6cd ("ARM: imx3: Remove imx3 soc_init()")
there are no more users of struct sdma_script_start_addrs outside
of the driver itself, thus let's move the struct declaration just
to the driver source code and remove the header file as unused one.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210620191103.156626-1-vz@mleia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Bunch of driver fixes, notably:
- More idxd fixes for driver unregister, error handling and bus
assignment
- HAS_IOMEM depends fix for few drivers
- lock fix in pl330 driver
- xilinx drivers fixes for initialize registers, missing dependencies
and limiting descriptor IDs
- mediatek descriptor management fixes
-----BEGIN PGP SIGNATURE-----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=FL1v
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine fixes from Vinod Koul:
"A bunch of driver fixes, notably:
- More idxd fixes for driver unregister, error handling and bus
assignment
- HAS_IOMEM depends fix for few drivers
- lock fix in pl330 driver
- xilinx drivers fixes for initialize registers, missing dependencies
and limiting descriptor IDs
- mediatek descriptor management fixes"
* tag 'dmaengine-fix-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
dmaengine: mediatek: use GFP_NOWAIT instead of GFP_ATOMIC in prep_dma
dmaengine: mediatek: do not issue a new desc if one is still current
dmaengine: mediatek: free the proper desc in desc_free handler
dmaengine: ipu: fix doc warning in ipu_irq.c
dmaengine: rcar-dmac: Fix PM reference leak in rcar_dmac_probe()
dmaengine: idxd: Fix missing error code in idxd_cdev_open()
dmaengine: stedma40: add missing iounmap() on error in d40_probe()
dmaengine: SF_PDMA depends on HAS_IOMEM
dmaengine: QCOM_HIDMA_MGMT depends on HAS_IOMEM
dmaengine: ALTERA_MSGDMA depends on HAS_IOMEM
dmaengine: idxd: Add missing cleanup for early error out in probe call
dmaengine: xilinx: dpdma: Limit descriptor IDs to 16 bits
dmaengine: xilinx: dpdma: Add missing dependencies to Kconfig
dmaengine: stm32-mdma: fix PM reference leak in stm32_mdma_alloc_chan_resourc()
dmaengine: zynqmp_dma: Fix PM reference leak in zynqmp_dma_alloc_chan_resourc()
dmaengine: xilinx: dpdma: initialize registers before request_irq
dmaengine: pl330: fix wrong usage of spinlock flags in dma_cyclc
dmaengine: fsl-dpaa2-qdma: Fix error return code in two functions
dmaengine: idxd: add missing dsa driver unregister
dmaengine: idxd: add engine 'struct device' missing bus type assignment
Fix function name in xilinx/xilinx_dpdma.c comment to remove
a warning found by kernel-doc.
drivers/dma/xilinx/xilinx_dpdma.c:935: warning: expecting prototype for
xilinx_dpdma_chan_no_ostand(). Prototype was for
xilinx_dpdma_chan_notify_no_ostand() instead.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/1623222893-123227-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The second parameter of spinlock_irq[save/restore] function is flags,
which is the last input parameter of sf_pdma_prep_dma_memcpy().
So declare local variable 'iflags' to be used as the second parameter of
spinlock_irq[save/restore] function.
Signed-off-by: Austin Kim <austin.kim@lge.com>
Link: https://lore.kernel.org/r/20210611065336.GA1121@raspberrypi
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Remove the DT-based Renesas SHDMA DMA multiplexer driver, as it is
unused. The DMA multiplexer node and one DMA controller instance were
added to the R-Mobile APE6 .dtsi file, but DMA support was never fully
enabled, cfr. commit a19788612f ("dmaengine: sh: Remove R-Mobile
APE6 support").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/e9445a5f4ac15fc4d3b376b5e675e39f8c95b967.1623406640.git.geert+renesas@glider.be
Signed-off-by: Vinod Koul <vkoul@kernel.org>
SM8250 seems to work just fine, so add a shiny new compatible for it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210614235358.444834-2-konrad.dybcio@somainline.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into driver-core-next
We need the driver core fix in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using list_move_tail() instead of list_del() + list_add_tail().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/1623036035-30614-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
As recommended by the doc in:
Documentation/drivers-api/dmaengine/provider.rst
Use GFP_NOWAIT to not deplete the emergency pool.
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Link: https://lore.kernel.org/r/20210513192642.29446-4-granquet@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Avoid issuing a new desc if one is still being processed as this can
lead to some desc never being marked as completed.
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Link: https://lore.kernel.org/r/20210513192642.29446-3-granquet@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The desc_free handler assumed that the desc we want to free was always
the current one associated with the channel.
This is seldom the case and this is causing use after free crashes in
multiple places (tx/rx/terminate...).
BUG: KASAN: use-after-free in mtk_uart_apdma_rx_handler+0x120/0x304
Call trace:
dump_backtrace+0x0/0x1b0
show_stack+0x24/0x34
dump_stack+0xe0/0x150
print_address_description+0x8c/0x55c
__kasan_report+0x1b8/0x218
kasan_report+0x14/0x20
__asan_load4+0x98/0x9c
mtk_uart_apdma_rx_handler+0x120/0x304
mtk_uart_apdma_irq_handler+0x50/0x80
__handle_irq_event_percpu+0xe0/0x210
handle_irq_event+0x8c/0x184
handle_fasteoi_irq+0x1d8/0x3ac
__handle_domain_irq+0xb0/0x110
gic_handle_irq+0x50/0xb8
el0_irq_naked+0x60/0x6c
Allocated by task 3541:
__kasan_kmalloc+0xf0/0x1b0
kasan_kmalloc+0x10/0x1c
kmem_cache_alloc_trace+0x90/0x2dc
mtk_uart_apdma_prep_slave_sg+0x6c/0x1a0
mtk8250_dma_rx_complete+0x220/0x2e4
vchan_complete+0x290/0x340
tasklet_action_common+0x220/0x298
tasklet_action+0x28/0x34
__do_softirq+0x158/0x35c
Freed by task 3541:
__kasan_slab_free+0x154/0x224
kasan_slab_free+0x14/0x24
slab_free_freelist_hook+0xf8/0x15c
kfree+0xb4/0x278
mtk_uart_apdma_desc_free+0x34/0x44
vchan_complete+0x1bc/0x340
tasklet_action_common+0x220/0x298
tasklet_action+0x28/0x34
__do_softirq+0x158/0x35c
The buggy address belongs to the object at ffff000063606800
which belongs to the cache kmalloc-256 of size 256
The buggy address is located 176 bytes inside of
256-byte region [ffff000063606800, ffff000063606900)
The buggy address belongs to the page:
page:fffffe00016d8180 refcount:1 mapcount:0 mapping:ffff00000302f600 index:0x0 compound_mapcount: 0
flags: 0xffff00000010200(slab|head)
raw: 0ffff00000010200 dead000000000100 dead000000000122 ffff00000302f600
raw: 0000000000000000 0000000080100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Link: https://lore.kernel.org/r/20210513192642.29446-2-granquet@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When testing x86 feature bits, use cpu_feature_enabled() so that
build-disabled features can remain off, regardless of what CPUID says.
Fixes: 8e50d39265 ("dmaengine: idxd: Add shared workqueue support")
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-By: Vinod Koul <vkoul@kernel.org>
Cc: <stable@vger.kernel.org>
Fix the following make W=1 warning and correct description:
drivers/dma/ipu/ipu_irq.c:238: warning: expecting prototype for ipu_irq_map(). Prototype was for ipu_irq_unmap() instead
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210603072425.2973570-1-yangyingliang@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1622442963-54095-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The error code is missing in this code scenario, add the error code
'-EINVAL' to the return value 'rc'.
Eliminate the follow smatch warning:
drivers/dma/idxd/cdev.c:113 idxd_cdev_open() warn: missing error code
'rc'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/1622628446-87909-1-git-send-email-jiapeng.chong@linux.alibaba.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There's no need to restore DMA context on CPU_CLUSTER_PM_ENTER_FAILED as
the DMA context won't be lost on errors.
Note that this does not cause invalid context restore as we already check
for busy DMA with omap_dma_busy() in CPU_CLUSTER_PM_ENTER, and block any
deeper idle states for the SoC by returning NOTIFY_BAD if busy.
If other drivers block deeper idle states with cpu_pm, we now just do a
pointless restore, but only if dma was not busy on CPU_CLUSTER_PM_ENTER.
Let's update the CPU_CLUSTER_PM_ENTER_FAILED handling for correctness,
and add a comment.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Adam Ford <aford173@gmail.com>
Cc: Andreas Kemnade <andreas@kemnade.info>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210518074347.16908-1-tony@atomide.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the missing iounmap() before return from d40_probe()
in the error handling case.
Fixes: 8d318a50b3 ("DMAENGINE: Support for ST-Ericssons DMA40 block v3")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210518141108.1324127-1-yangyingliang@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When CONFIG_HAS_IOMEM is not set/enabled, certain iomap() family
functions [including ioremap(), devm_ioremap(), etc.] are not
available.
Drivers that use these functions should depend on HAS_IOMEM so that
they do not cause build errors.
Mends this build error:
s390-linux-ld: drivers/dma/sf-pdma/sf-pdma.o: in function `sf_pdma_probe':
sf-pdma.c:(.text+0x1668): undefined reference to `devm_ioremap_resource'
Fixes: 6973886ad5 ("dmaengine: sf-pdma: add platform DMA support for HiFive Unleashed A00")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Green Wan <green.wan@sifive.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: dmaengine@vger.kernel.org
Link: https://lore.kernel.org/r/20210522021313.16405-4-rdunlap@infradead.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When CONFIG_HAS_IOMEM is not set/enabled, certain iomap() family
functions [including ioremap(), devm_ioremap(), etc.] are not
available.
Drivers that use these functions should depend on HAS_IOMEM so that
they do not cause build errors.
Rectifies these build errors:
s390-linux-ld: drivers/dma/qcom/hidma_mgmt.o: in function `hidma_mgmt_probe':
hidma_mgmt.c:(.text+0x780): undefined reference to `devm_ioremap_resource'
s390-linux-ld: drivers/dma/qcom/hidma_mgmt.o: in function `hidma_mgmt_init':
hidma_mgmt.c:(.init.text+0x126): undefined reference to `of_address_to_resource'
s390-linux-ld: hidma_mgmt.c:(.init.text+0x16e): undefined reference to `of_address_to_resource'
Fixes: 67a2003e06 ("dmaengine: add Qualcomm Technologies HIDMA channel driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Sinan Kaya <okaya@codeaurora.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: dmaengine@vger.kernel.org
Link: https://lore.kernel.org/r/20210522021313.16405-3-rdunlap@infradead.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When CONFIG_HAS_IOMEM is not set/enabled, certain iomap() family
functions [including ioremap(), devm_ioremap(), etc.] are not
available.
Drivers that use these functions should depend on HAS_IOMEM so that
they do not cause build errors.
Repairs this build error:
s390-linux-ld: drivers/dma/altera-msgdma.o: in function `request_and_map':
altera-msgdma.c:(.text+0x14b0): undefined reference to `devm_ioremap'
Fixes: a85c6f1b29 ("dmaengine: Add driver for Altera / Intel mSGDMA IP core")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: dmaengine@vger.kernel.org
Reviewed-by: Stefan Roese <sr@denx.de>
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr@denx.de
Link: https://lore.kernel.org/r/20210522021313.16405-2-rdunlap@infradead.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The probe call stack is missing some cleanup when things fail in the
middle. Add the appropriate cleanup routines to make sure we exit
gracefully.
Fixes: a39c7cd043 ("dmaengine: idxd: removal of pcim managed mmio mapping")
Reported-by: Nikhil Rao <nikhil.rao@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/162197061707.392656.15760573520817310791.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The hardware retrigger is inherently racy with the vsync interrupt. This
isn't an issue as the hardware provides a way to detect a race loss and
handle it correctly. When debugging issues related to this, it's useful
to get a notification of the race loss. Add a debug message to do so.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jianqiang Chen <jianqiang.chen@xilinx.com>
Reviewed-by: Jianqiang Chen <jianqiang.chen@xilinx.com>
Link: https://lore.kernel.org/r/20210520152420.23986-4-laurent.pinchart@ideasonboard.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To ease debugging, add the channel number to all kernel log messages
related to a particular channel.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jianqiang Chen <jianqiang.chen@xilinx.com>
Reviewed-by: Jianqiang Chen <jianqiang.chen@xilinx.com>
Link: https://lore.kernel.org/r/20210520152420.23986-3-laurent.pinchart@ideasonboard.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
While the descriptor ID is stored in a 32-bit field in the hardware
descriptor, only 16 bits are used by the hardware and are reported
through the XILINX_DPDMA_CH_DESC_ID register. Failure to handle the
wrap-around results in a descriptor ID mismatch after 65536 frames. Fix
it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jianqiang Chen <jianqiang.chen@xilinx.com>
Reviewed-by: Jianqiang Chen <jianqiang.chen@xilinx.com>
Link: https://lore.kernel.org/r/20210520152420.23986-5-laurent.pinchart@ideasonboard.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver depends on both OF and IOMEM support, express those
dependencies in Kconfig. This fixes a build failure on S390 reported by
the 0day bot.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jianqiang Chen <jianqiang.chen@xilinx.com>
Reviewed-by: Jianqiang Chen <jianqiang.chen@xilinx.com>
Link: https://lore.kernel.org/r/20210520152420.23986-2-laurent.pinchart@ideasonboard.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20210517081826.1564698-2-yukuai3@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20210517081826.1564698-4-yukuai3@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Place a comment in hidma_mgmt_init explaining why success must
currently be assumed, due to the cleanup issue that would need to
be considered were this module ever to be unloadable or were this
platform_driver_register call ever to fail.
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-By: Sinan Kaya <okaya@kernel.org>
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20210503115736.2104747-52-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit a474b3f042.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original change is NOT correct, as it does not correctly unwind from
the resources that was allocated before the call to
platform_driver_register().
Cc: Aditya Pakki <pakki001@umn.edu>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-By: Sinan Kaya <okaya@kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-51-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With commit 312c004d36 ("[PATCH] driver core: replace "hotplug" by
"uevent"") already in the tree over a decade, update the name of
FW_ACTION defines to follow semantics, and reflect what the defines are
really meant for, i.e. whether or not generate user space event.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210425020024.28057-1-shawn.guo@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
flags varible which is the input parameter of pl330_prep_dma_cyclic()
should not be used by spinlock_irq[save/restore] function.
Signed-off-by: Jongho Park <jongho7.park@samsung.com>
Signed-off-by: Bumyong Lee <bumyong.lee@samsung.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20210507063647.111209-1-chanho61.park@samsung.com
Fixes: f6f2421c0a ("dmaengine: pl330: Merge dma_pl330_dmac and pl330_dmac structs")
Cc: stable@vger.kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix to return a negative error code from the error handling case instead
of 0, as done elsewhere in the function where it is.
Fixes: 7fdf9b05c7 ("dmaengine: fsl-dpaa2-qdma: Add NXP dpaa2 qDMA controller driver for Layerscape SoCs")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210508030056.2027-1-thunder.leizhen@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Allocation of idxd->int_handles was merged incorrectly for the 5.13 merge
window. The devm_kcalloc should've been regular kcalloc due to devm_*
removal series for the driver.
Fixes: eb15e7154f ("dmaengine: idxd: add interrupt handle request and release support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/162060710518.130816.11349798049329202863.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Variable cdev_ctx is set to '&ictx[wq->idxd->data->type]' but this
value is not used, hence it is a redundant assignment and can be
removed.
Clean up the following clang-analyzer warning:
drivers/dma/idxd/cdev.c:300:2: warning: Value stored to 'cdev_ctx' is
never read [clang-analyzer-deadcode.DeadStores].
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/1620298847-33127-1-git-send-email-jiapeng.chong@linux.alibaba.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For fix below warning reported by static code analysis tool like Coverity
from Synopsys:
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Addresses-Coverity-ID: 12285639 ("Unchecked return value")
Link: https://lore.kernel.org/r/1619427549-20498-1-git-send-email-yibin.gong@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
New drivers/devices
- Support for QCOM SM8150 GPI DMA
Updates:
- Big pile of idxd updates including support for performance monitoring
- Support in dw-edma for interleaved dma
- Support for synchronize() in Xilinx driver
-----BEGIN PGP SIGNATURE-----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=Jjb4
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"New drivers/devices:
- Support for QCOM SM8150 GPI DMA
Updates:
- Big pile of idxd updates including support for performance
monitoring
- Support in dw-edma for interleaved dma
- Support for synchronize() in Xilinx driver"
* tag 'dmaengine-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (42 commits)
dmaengine: idxd: Enable IDXD performance monitor support
dmaengine: idxd: Add IDXD performance monitor support
dmaengine: idxd: remove MSIX masking for interrupt handlers
dmaengine: idxd: device cmd should use dedicated lock
dmaengine: idxd: support reporting of halt interrupt
dmaengine: idxd: enable SVA feature for IOMMU
dmaengine: idxd: convert sprintf() to sysfs_emit() for all usages
dmaengine: idxd: add interrupt handle request and release support
dmaengine: idxd: add support for readonly config mode
dmaengine: idxd: add percpu_ref to descriptor submission path
dmaengine: idxd: remove detection of device type
dmaengine: idxd: iax bus removal
dmaengine: idxd: fix cdev setup and free device lifetime issues
dmaengine: idxd: fix group conf_dev lifetime
dmaengine: idxd: fix engine conf_dev lifetime
dmaengine: idxd: fix wq conf_dev 'struct device' lifetime
dmaengine: idxd: fix idxd conf_dev 'struct device' lifetime
dmaengine: idxd: use ida for device instance enumeration
dmaengine: idxd: removal of pcim managed mmio mapping
dmaengine: idxd: cleanup pci interrupt vector allocation management
...
Updates for SoC specific drivers include a few subsystems that
have their own maintainers but send them through the soc tree:
TEE/OP-TEE:
- Add tracepoints around calls to secure world
Memory controller drivers:
- Minor fixes for Renesas, Exynos, Mediatek and Tegra platforms
- Add debug statistics to Tegra20 memory controller
- Update Tegra bindings and convert to dtschema
ARM SCMI Firmware:
- Support for modular SCMI protocols and vendor specific extensions
- New SCMI IIO driver
- Per-cpu DVFS
The other driver changes are all from the platform maintainers
directly and reflect the drivers that don't fit into any other
subsystem as well as treewide changes for a particular platform.
SoCFPGA:
- Various cleanups contributed by Krzysztof Kozlowski
Mediatek:
- add MT8183 support to mutex driver
- MMSYS: use per SoC array to describe the possible routing
- add MMSYS support for MT8183 and MT8167
- add support for PMIC wrapper with integrated arbiter
- add support for MT8192/MT6873
Tegra:
- Bug fixes to PMC and clock drivers
NXP/i.MX:
- Update SCU power domain driver to keep console domain power on.
- Add missing ADC1 power domain to SCU power domain driver.
- Update comments for single global power domain in SCU power domain
driver.
- Add i.MX51/i.MX53 unique id support to i.MX SoC driver.
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance optimized
for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
OMAP:
- Preparation to use devicetree for genpd
- ti-sysc needs iorange check improved when the interconnect target module
has no control registers listed
- ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to avoid
issues with missing resources and unnecessary deferred probe
- ti-sysc debug option can now detect more devices
- ti-sysc now warns if an old incomplete devicetree data is found as we
now rely on it being complete for am3 and 4
- soc init code needs to check for prcm and prm nodes for omap4/5 and dra7
- omap-prm driver needs to enable autoidle retention support for omap4
- omap5 clocks are missing gpmc and ocmc clock registers
- pci-dra7xx now needs to use builtin_platform_driver instead of using
builtin_platform_driver_probe for deferred probe to work
Raspberry Pi:
- Fix-up all RPi firmware drivers so as for unbind to happen in an
orderly fashion
- Support for RPi's PoE hat PWM bus
Qualcomm
- Improved detection for SCM calling conventions
- Support for OEM specific wifi firmware path
- Added drivers for SC7280/SM8350: RPMH, LLCC< AOSS QMP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=iidq
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Updates for SoC specific drivers include a few subsystems that have
their own maintainers but send them through the soc tree:
TEE/OP-TEE:
- Add tracepoints around calls to secure world
Memory controller drivers:
- Minor fixes for Renesas, Exynos, Mediatek and Tegra platforms
- Add debug statistics to Tegra20 memory controller
- Update Tegra bindings and convert to dtschema
ARM SCMI Firmware:
- Support for modular SCMI protocols and vendor specific extensions
- New SCMI IIO driver
- Per-cpu DVFS
The other driver changes are all from the platform maintainers
directly and reflect the drivers that don't fit into any other
subsystem as well as treewide changes for a particular platform.
SoCFPGA:
- Various cleanups contributed by Krzysztof Kozlowski
Mediatek:
- add MT8183 support to mutex driver
- MMSYS: use per SoC array to describe the possible routing
- add MMSYS support for MT8183 and MT8167
- add support for PMIC wrapper with integrated arbiter
- add support for MT8192/MT6873
Tegra:
- Bug fixes to PMC and clock drivers
NXP/i.MX:
- Update SCU power domain driver to keep console domain power on.
- Add missing ADC1 power domain to SCU power domain driver.
- Update comments for single global power domain in SCU power domain
driver.
- Add i.MX51/i.MX53 unique id support to i.MX SoC driver.
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance
optimized for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
OMAP:
- Preparation to use devicetree for genpd
- ti-sysc needs iorange check improved when the interconnect target
module has no control registers listed
- ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to
avoid issues with missing resources and unnecessary deferred probe
- ti-sysc debug option can now detect more devices
- ti-sysc now warns if an old incomplete devicetree data is found as
we now rely on it being complete for am3 and 4
- soc init code needs to check for prcm and prm nodes for omap4/5 and
dra7
- omap-prm driver needs to enable autoidle retention support for
omap4
- omap5 clocks are missing gpmc and ocmc clock registers
- pci-dra7xx now needs to use builtin_platform_driver instead of
using builtin_platform_driver_probe for deferred probe to work
Raspberry Pi:
- Fix-up all RPi firmware drivers so as for unbind to happen in an
orderly fashion
- Support for RPi's PoE hat PWM bus
Qualcomm
- Improved detection for SCM calling conventions
- Support for OEM specific wifi firmware path
- Added drivers for SC7280/SM8350: RPMH, LLCC< AOSS QMP"
* tag 'arm-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
soc: aspeed: fix a ternary sign expansion bug
memory: mtk-smi: Add device-link between smi-larb and smi-common
memory: samsung: exynos5422-dmc: handle clk_set_parent() failure
memory: renesas-rpc-if: fix possible NULL pointer dereference of resource
clk: socfpga: fix iomem pointer cast on 64-bit
soc: aspeed: Adapt to new LPC device tree layout
pinctrl: aspeed-g5: Adapt to new LPC device tree layout
ipmi: kcs: aspeed: Adapt to new LPC DTS layout
ARM: dts: Remove LPC BMC and Host partitions
dt-bindings: aspeed-lpc: Remove LPC partitioning
soc: fsl: enable acpi support in RCPM driver
soc: qcom: mdt_loader: Detect truncated read of segments
soc: qcom: mdt_loader: Validate that p_filesz < p_memsz
soc: qcom: pdr: Fix error return code in pdr_register_listener
firmware: qcom_scm: Fix kernel-doc function names to match
firmware: qcom_scm: Suppress sysfs bind attributes
firmware: qcom_scm: Workaround lack of "is available" call on SC7180
firmware: qcom_scm: Reduce locking section for __get_convention()
firmware: qcom_scm: Make __qcom_scm_is_call_available() return bool
Revert "soc: fsl: qe: introduce qe_io{read,write}* wrappers"
...
Add the code needed in the main IDXD driver to interface with the IDXD
perfmon implementation.
[ Based on work originally by Jing Lin. ]
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Link: https://lore.kernel.org/r/a5564a5583911565d31c2af9234218c5166c4b2c.1619276133.git.zanussi@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Implement the IDXD performance monitor capability (named 'perfmon' in
the DSA (Data Streaming Accelerator) spec [1]), which supports the
collection of information about key events occurring during DSA and
IAX (Intel Analytics Accelerator) device execution, to assist in
performance tuning and debugging.
The idxd perfmon support is implemented as part of the IDXD driver and
interfaces with the Linux perf framework. It has several features in
common with the existing uncore pmu support:
- it does not support sampling
- does not support per-thread counting
However it also has some unique features not present in the core and
uncore support:
- all general-purpose counters are identical, thus no event constraints
- operation is always system-wide
While the core perf subsystem assumes that all counters are by default
per-cpu, the uncore pmus are socket-scoped and use a cpu mask to
restrict counting to one cpu from each socket. IDXD counters use a
similar strategy but expand the scope even further; since IDXD
counters are system-wide and can be read from any cpu, the IDXD perf
driver picks a single cpu to do the work (with cpu hotplug notifiers
to choose a different cpu if the chosen one is taken off-line).
More specifically, the perf userspace tool by default opens a counter
for each cpu for an event. However, if it finds a cpumask file
associated with the pmu under sysfs, as is the case with the uncore
pmus, it will open counters only on the cpus specified by the cpumask.
Since perfmon only needs to open a single counter per event for a
given IDXD device, the perfmon driver will create a sysfs cpumask file
for the device and insert the first cpu of the system into it. When a
user uses perf to open an event, perf will open a single counter on
the cpu specified by the cpu mask. This amounts to the default
system-wide rather than per-cpu counting mentioned previously for
perfmon pmu events. In order to keep the cpu mask up-to-date, the
driver implements cpu hotplug support for multiple devices, as IDXD
usually enumerates and registers more than one idxd device.
The perfmon driver implements basic perfmon hardware capability
discovery and configuration, and is initialized by the IDXD driver's
probe function. During initialization, the driver retrieves the total
number of supported performance counters, the pmu ID, and the device
type from idxd device, and registers itself under the Linux perf
framework.
The perf userspace tool can be used to monitor single or multiple
events depending on the given configuration, as well as event groups,
which are also supported by the perfmon driver. The user configures
events using the perf tool command-line interface by specifying the
event and corresponding event category, along with an optional set of
filters that can be used to restrict counting to specific work queues,
traffic classes, page and transfer sizes, and engines (See [1] for
specifics).
With the configuration specified by the user, the perf tool issues a
system call passing that information to the kernel, which uses it to
initialize the specified event(s). The event(s) are opened and
started, and following termination of the perf command, they're
stopped. At that point, the perfmon driver will read the latest count
for the event(s), calculate the difference between the latest counter
values and previously tracked counter values, and display the final
incremental count as the event count for the cycle. An overflow
handler registered on the IDXD irq path is used to account for counter
overflows, which are signaled by an overflow interrupt.
Below are a couple of examples of perf usage for monitoring DSA events.
The following monitors all events in the 'engine' category. Becuuse
no filters are specified, this captures all engine events for the
workload, which in this case is 19 iterations of the work generated by
the kernel dmatest module.
Details describing the events can be found in Appendix D of [1],
Performance Monitoring Events, but briefly they are:
event 0x1: total input data processed, in 32-byte units
event 0x2: total data written, in 32-byte units
event 0x4: number of work descriptors that read the source
event 0x8: number of work descriptors that write the destination
event 0x10: number of work descriptors dispatched from batch descriptors
event 0x20: number of work descriptors dispatched from work queues
# perf stat -e dsa0/event=0x1,event_category=0x1/,
dsa0/event=0x2,event_category=0x1/,
dsa0/event=0x4,event_category=0x1/,
dsa0/event=0x8,event_category=0x1/,
dsa0/event=0x10,event_category=0x1/,
dsa0/event=0x20,event_category=0x1/
modprobe dmatest channel=dma0chan0 timeout=2000
iterations=19 run=1 wait=1
Performance counter stats for 'system wide':
5,332 dsa0/event=0x1,event_category=0x1/
5,327 dsa0/event=0x2,event_category=0x1/
19 dsa0/event=0x4,event_category=0x1/
19 dsa0/event=0x8,event_category=0x1/
0 dsa0/event=0x10,event_category=0x1/
19 dsa0/event=0x20,event_category=0x1/
21.977436186 seconds time elapsed
The command below illustrates filter usage with a simple example. It
specifies that MEM_MOVE operations should be counted for the DSA
device dsa0 (event 0x8 corresponds to the EV_MEM_MOVE event - Number
of Memory Move Descriptors, which is part of event category 0x3 -
Operations. The detailed category and event IDs are available in
Appendix D, Performance Monitoring Events, of [1]). In addition to
the event and event category, a number of filters are also specified
(the detailed filter values are available in Chapter 6.4 (Filter
Support) of [1]), which will restrict counting to only those events
that meet all of the filter criteria. In this case, the filters
specify that only MEM_MOVE operations that are serviced by work queue
wq0 and specifically engine number engine0 and traffic class tc0
having sizes between 0 and 4k and page size of between 0 and 1G result
in a counter hit; anything else will be filtered out and not appear in
the final count. Note that filters are optional - any filter not
specified is assumed to be all ones and will pass anything.
# perf stat -e dsa0/filter_wq=0x1,filter_tc=0x1,filter_sz=0x7,
filter_eng=0x1,event=0x8,event_category=0x3/
modprobe dmatest channel=dma0chan0 timeout=2000
iterations=19 run=1 wait=1
Performance counter stats for 'system wide':
19 dsa0/filter_wq=0x1,filter_tc=0x1,filter_sz=0x7,
filter_eng=0x1,event=0x8,event_category=0x3/
21.865914091 seconds time elapsed
The output above reflects that the unspecified workload resulted in
the counting of 19 MEM_MOVE operation events that met the filter
criteria.
[1]: https://software.intel.com/content/www/us/en/develop/download/intel-data-streaming-accelerator-preliminary-architecture-specification.html
[ Based on work originally by Jing Lin. ]
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Link: https://lore.kernel.org/r/0c5080a7d541904c4ad42b848c76a1ce056ddac7.1619276133.git.zanussi@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Remove interrupt masking and just let the hard irq handler keep
firing for new events. This is less of a performance impact vs
the MMIO readback inside the pci_msi_{mask,unmas}_irq(). Especially
with a loaded system those flushes can be stuck behind large amounts
of MMIO writes to flush. When guest kernel is running on top of VFIO
mdev, mask/unmask causes a vmexit each time and is not desirable.
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/161894523436.3210025.1834640110556139277.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Create a dedicated lock for device command operations. Put the device
command operation under finer grained locking instead of using the
idxd->dev_lock.
Suggested-by: Sanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161894525685.3210132.16160045731436382560.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Enable IOMMU_DEV_FEAT_SVA before attempt to bind pasid. This is needed
according to iommu_sva_bind_device() comment. Currently Intel IOMMU code
does this before bind call. It really needs to be controlled by the driver.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161894440621.3202472.17644507396206848134.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
DSA spec states that when Request Interrupt Handle and Release Interrupt
Handle command bits are set in the CMDCAP register, these device commands
must be supported by the driver.
The interrupt handle is programmed in a descriptor. When Request Interrupt
Handle is not supported, the interrupt handle is the index of the desired
entry in the MSI-X table. When the command is supported, driver must use
the command to obtain a handle to be programmed in the submitted
descriptor.
A requested handle may be revoked. After the handle is revoked, any use of
the handle will result in Invalid Interrupt Handle error.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161894439422.3202472.17579543737810265471.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The read-only configuration mode is defined by the DSA spec as a mode of
the device WQ configuration. When GENCAP register bit 31 is set to 0,
the device is in RO mode and group configuration and some fields of the
workqueue configuration registers are read-only and reflect the fixed
configuration of the device. Add support for RO mode. The driver will
load the values from the registers directly setup all the internally
cached data structures based on the device configuration.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161894438847.3202472.6317563824045432727.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Current submission path has no way to restrict the submitter from
stop submiting on shutdown path or wq disable path. This provides a way to
quiesce the submission path.
Modeling after 'struct reqeust_queue' usage of percpu_ref. One of the
abilities of per_cpu reference counting is the ability to stop new
references from being taken while awaiting outstanding references to be
dropped. On wq shutdown, we want to block any new submissions to the kernel
workqueue and quiesce before disabling. The percpu_ref allows us to block
any new submissions and wait for any current submission calls to finish
submitting to the workqueue.
A percpu_ref is embedded in each idxd_wq context to allow control for
individual wq. The wq->wq_active counter is elevated before calling
movdir64b() or enqcmds() to submit a descriptor to the wq and dropped once
the submission call completes. The function is gated by
percpu_ref_tryget_live(). On shutdown with percpu_ref_kill() called, any
new submission would be blocked from acquiring a ref and failed. Once all
references are dropped for the wq, shutdown can continue.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161894438293.3202472.14894701611500822232.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Move all static data type for per device type to an idxd_driver_data data
structure. The data can be attached to the pci_device_id and provided by
the pci probe function. This removes a lot of unnecessary type detection
and setup code.
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161852988924.2203940.2787590808682466398.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is no need to have an additional bus for the IAX device. The removal
of IAX will change user ABI as /sys/bus/iax will no longer exist.
The iax device will be moved to the dsa bus. The device id for dsa and
iax will now be combined rather than unique for each device type in order
to accommodate the iax devices. This is in preparation for fixing the
sub-driver code for idxd. There's no hardware deployment for Sapphire
Rapids platform yet, which means that users have no reason to have
developed scripts against this ABI. There is some exposure to
released versions of accel-config, but those are being fixed up and
an accel-config upgrade is reasonable to get IAX support. As far as
accel-config is concerned IAX support starts when these devices appear
under /sys/bus/dsa, and old accel-config just assumes that an empty /
missing /sys/bus/iax just means a lack of platform support.
Fixes: f25b463883 ("dmaengine: idxd: add IAX configuration support in the IDXD driver")
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161852988298.2203940.4529909758034944428.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The char device setup and cleanup has device lifetime issues regarding when
parts are initialized and cleaned up. The initialization of struct device is
done incorrectly. device_initialize() needs to be called on the 'struct
device' and then additional changes can be added. The ->release() function
needs to be setup via device_type before dev_set_name() to allow proper
cleanup. The change re-parents the cdev under the wq->conf_dev to get
natural reference inheritance. No known dependency on the old device path exists.
Reported-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes: 42d279f913 ("dmaengine: idxd: add char driver to expose submission portal to userland")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/161852987721.2203940.1478218825576630810.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Remove devm_* allocation and fix group->conf_dev 'struct device'
lifetime. Address issues flagged by CONFIG_DEBUG_KOBJECT_RELEASE.
Add release functions in order to free the allocated memory at the
group->conf_dev destruction time.
Reported-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes: bfe1d56091 ("dmaengine: idxd: Init and probe for Intel data accelerators")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161852987144.2203940.8830315575880047.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Remove devm_* allocation and fix engine->conf_dev 'struct device'
lifetime. Address issues flagged by CONFIG_DEBUG_KOBJECT_RELEASE.
Add release functions in order to free the allocated memory at the
engine conf_dev destruction time.
Reported-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes: bfe1d56091 ("dmaengine: idxd: Init and probe for Intel data accelerators")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161852986460.2203940.16603218225412118431.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Remove devm_* allocation and fix wq->conf_dev 'struct device' lifetime.
Address issues flagged by CONFIG_DEBUG_KOBJECT_RELEASE. Add release
functions in order to free the allocated memory for the wq context at
device destruction time.
Reported-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes: bfe1d56091 ("dmaengine: idxd: Init and probe for Intel data accelerators")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161852985907.2203940.6840120734115043753.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The devm managed lifetime is incompatible with 'struct device' objects that
resides in idxd context. This is one of the series that clean up the idxd
driver 'struct device' lifetime. Fix idxd->conf_dev 'struct device'
lifetime. Address issues flagged by CONFIG_DEBUG_KOBJECT_RELEASE.
Add release functions in order to free the allocated memory at the
appropriate time.
Reported-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes: bfe1d56091 ("dmaengine: idxd: Init and probe for Intel data accelerators")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161852985319.2203940.4650791514462735368.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The devm managed lifetime is incompatible with 'struct device' objects that
resides in idxd context. This is one of the series that clean up the idxd
driver 'struct device' lifetime. Remove pcim_* management of the PCI device
and the ioremap of MMIO BAR and replace with unmanaged versions. This is
for consistency of removing all the pcim/devm based calls.
Reported-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes: bfe1d56091 ("dmaengine: idxd: Init and probe for Intel data accelerators")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/161852984150.2203940.8043988289748519056.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The devm managed lifetime is incompatible with 'struct device' objects that
resides in idxd context. This is one of the series that clean up the idxd
driver 'struct device' lifetime. Remove devm managed pci interrupt vectors
and replace with unmanged allocators.
Reported-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes: bfe1d56091 ("dmaengine: idxd: Init and probe for Intel data accelerators")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/161852983563.2203940.8116028229124776669.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The devm managed lifetime is incompatible with 'struct device' objects that
resides in idxd context. This is one of the series that clean up the idxd
driver 'struct device' lifetime. Remove embedding of dma_device and dma_chan
in idxd since it's not the only interface that idxd will use. The freeing of
the dma_device will be managed by the ->release() function.
Reported-by: Jason Gunthorpe <jgg@nvidia.com>
Fixes: bfe1d56091 ("dmaengine: idxd: Init and probe for Intel data accelerators")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/161852983001.2203940.14817017492384561719.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are calls to idxd_cmd_exec that pass a null status pointer however
a recent commit has added an assignment to *status that can end up
with a null pointer dereference. The function expects a null status
pointer sometimes as there is a later assignment to *status where
status is first null checked. Fix the issue by null checking status
before making the assignment.
Addresses-Coverity: ("Explicit null dereferenced")
Fixes: 89e3becd8f ("dmaengine: idxd: check device state before issue command")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20210415110654.1941580-1-colin.king@canonical.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
A pre-release silicon erratum workaround where wq reset does not clear
WQCFG registers was leaked into upstream code. Use wq reset command
instead of blasting the MMIO region. This also address an issue where
we clobber registers in future devices.
Fixes: da32b28c95 ("dmaengine: idxd: cleanup workqueue config after disabling")
Reported-by: Shreenivaas Devarajan <shreenivaas.devarajan@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161824330020.881560.16375921906426627033.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add disabling/clearing of MSIX permission entries on device shutdown to
mirror the enabling of the MSIX entries on probe. Current code left the
MSIX enabled and the pasid entries still programmed at device shutdown.
Fixes: 8e50d39265 ("dmaengine: idxd: Add shared workqueue support")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161824457969.882533.6020239898682672311.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
pm_runtime_get_sync() will increase the runtime PM counter
even it returns an error. Thus a pairing decrement is needed
to prevent refcount leak. Fix this by replacing this API with
pm_runtime_resume_and_get(), which will not change the runtime
PM counter on error.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210409082805.23643-1-dinghao.liu@zju.edu.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In the first list_for_each_entry() macro of dma_async_device_register,
it gets the chan from list and calls __dma_async_device_channel_register
(..,chan). We can see that chan->local is allocated by alloc_percpu() and
it is freed chan->local by free_percpu(chan->local) when
__dma_async_device_channel_register() failed.
But after __dma_async_device_channel_register() failed, the caller will
goto err_out and freed the chan->local in the second time by free_percpu().
The cause of this problem is forget to set chan->local to NULL when
chan->local was freed in __dma_async_device_channel_register(). My
patch sets chan->local to NULL when the callee failed to avoid double free.
Fixes: d2fb0a0438 ("dmaengine: break out channel registration")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20210331014458.3944-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some architectures do not provide devm_*() APIs. Hence make the driver
dependent on HAVE_IOMEM.
Fixes: dbde5c2934 ("dw_dmac: use devm_* functions to simplify code")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20210324141757.24710-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
WQ size can only be changed when the device is disabled. Current code
allows change when device is enabled but wq is disabled. Change the check
to detect device state.
Fixes: c52ca47823 ("dmaengine: idxd: add configuration component of driver")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161782558755.107710.18138252584838406025.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The operation capability register is 256bits. The current output only
prints out the first 64bits. Fix to output the entire 256bits. The current
code omits operation caps from IAX devices.
Fixes: c52ca47823 ("dmaengine: idxd: add configuration component of driver")
Reported-by: Lucas Van <lucas.van@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161645624963.2003736.829798666998490151.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Current code blindly writes over the SWERR and the OVERFLOW bits. Write
back the bits actually read instead so the driver avoids clobbering the
OVERFLOW bit that comes after the register is read.
Fixes: bfe1d56091 ("dmaengine: idxd: Init and probe for Intel data accelerators")
Reported-by: Sanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161352082229.3511254.1002151220537623503.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
ARCH_SOCFPGA is being renamed to ARCH_INTEL_SOCFPGA so adjust the
32-bit ARM drivers to rely on new symbol.
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Currently, is missing a null check on a pcim_iomap_table() return value
and this can lead to a null pointer dereference if the desired BAR
wasn't mapped previously.
Fix this by adding a null check and returning -ENOMEM.
Addresses-Coverity: ("Dereference null return")
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Link: https://lore.kernel.org/r/bc5e6b8632c84660bb6dae454980e9419992ed14.1613674948.git.gustavo.pimentel@synopsys.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When the driver is compiled as a module and loaded if we try to unload
it, the Kernel shows a crash log. This Kernel crash is due to the
dma_async_device_unregister() call done after deleting the channels,
this patch fixes this issue.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Link: https://lore.kernel.org/r/4aa850c035cf7ee488f1d3fb6dee0e37be0dce0a.1613674948.git.gustavo.pimentel@synopsys.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Changes the linked list and data blocks offset and sizes to follow the
recommendation given by the hardware team for the IPK solution.
Although the previous data blocks offset and sizes are still valid and
functional, using them that might present some issues related to the IPK
solution, since this solution is based on FPGA and might be subjected to
timmings constrains.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Link: https://lore.kernel.org/r/f682e7f7f06dc6b2efdd431481d6fb4d762c2c05.1613674948.git.gustavo.pimentel@synopsys.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In the previous implementation, the driver assumed that there existed
only two memory spaces that would equally distribute the amount of
read/write channels.
This might not be the case on some other implementations, therefore this
patch change this requirement so that each write/read channel has
its own linked list and data space well defined, which allows
different sizes and locations.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Link: https://lore.kernel.org/r/2e316cb983f8a1e09ce929029f87619dc92a52de.1613674948.git.gustavo.pimentel@synopsys.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In the driver code structure, I tried to keep the code style consistency
by writing the write channels instructions first, and then follow by the
read channels instructions, mimicking the hardware implementation.
However, this code style failed in some cases. This patch fixes that and
no functional changes are expected.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Link: https://lore.kernel.org/r/9bd1f86f19df8bb5de502fb85a0c5dc07978a9ba.1613674948.git.gustavo.pimentel@synopsys.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for the HDMA feature.
This new feature enables the current eDMA IP to use a deeper prefetch
of the linked list, which reduces the algorithm execution latency
observed when loading the elements of the list, causing more stable
and higher data transfer.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Link: https://lore.kernel.org/r/5f40f89ef7d6255a12d5b23f34e6e59dcd28861e.1613674948.git.gustavo.pimentel@synopsys.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add writeq() and readq() for 64 bits architures support.
Supporting these two functions will allow the write or the read of eDMA
64 bits registers at once instead of having two consecutive operations.
Also, this improvement will allow the PCI optimization transaction
messages, which will generate a 64 bits message instead of two messages
of 32 bits.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Link: https://lore.kernel.org/r/3f1120f7c6003b38ec8b851fc68936007c4d9fd8.1613674948.git.gustavo.pimentel@synopsys.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Xilinx dmaengine driver uses a tasklet to process completed
descriptors and execute their callbacks.
Currently consumers of the DMA channel have to no method of synchronization
against this tasklet when using the Xilinx dmaengine drivers. This can lead
to race conditions when the consumer frees resources that are accessed in
the callback before the tasklet has finished running.
It is not enough to just call dmaengine_terminal_all() since on a
multi-processor system the tasklet can run concurrently to it and might
call the callback after dmaengine_terminate_all() has already finished.
To mitigate this issue implement the synchronize() callback for the driver,
which will wait until the tasklet has finished.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20210313125311.4823-1-lars@metafoo.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The active descriptor pointer is accessed from different contexts,
including different interrupt handlers, and its access must be protected
by the channel's lock. This wasn't done in the done IRQ handler. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20210307040629.29308-3-laurent.pinchart@ideasonboard.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When multiple channels are part of a video group, the transfer is
triggered only when all channels in the group are ready. The logic to do
so is incorrect, as it causes the descriptors for all channels but the
last one in a group to not being pushed to the hardware. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20210307040629.29308-2-laurent.pinchart@ideasonboard.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- Generalise byte swapping assembly
- Update debug addresses for STI
- Validate start of physical memory with DTB
- Do not clear SCTLR.nTLSMD in decompressor
- amba/locomo/sa1111 devices remove method return type is void
- address markers for KASAN in page table dump
-----BEGIN PGP SIGNATURE-----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=BULT
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- Generalise byte swapping assembly
- Update debug addresses for STI
- Validate start of physical memory with DTB
- Do not clear SCTLR.nTLSMD in decompressor
- amba/locomo/sa1111 devices remove method return type is void
- address markers for KASAN in page table dump
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9065/1: OABI compat: fix build when EPOLL is not enabled
ARM: 9055/1: mailbox: arm_mhuv2: make remove callback return void
amba: Make use of bus_type functions
amba: Make the remove callback return void
vfio: platform: simplify device removal
amba: reorder functions
amba: Fix resource leak for drivers without .remove
ARM: 9054/1: arch/arm/mm/mmu.c: Remove duplicate header
ARM: 9053/1: arm/mm/ptdump:Add address markers for KASAN regions
ARM: 9051/1: vdso: remove unneded extra-y addition
ARM: 9050/1: Kconfig: Select ARCH_HAVE_NMI_SAFE_CMPXCHG where possible
ARM: 9049/1: locomo: make locomo bus's remove callback return void
ARM: 9048/1: sa1111: make sa1111 bus's remove callback return void
ARM: 9047/1: smp: remove unused variable
ARM: 9046/1: decompressor: Do not clear SCTLR.nTLSMD for ARMv7+ cores
ARM: 9045/1: uncompress: Validate start of physical memory against passed DTB
ARM: 9042/1: debug: no uncompress debugging while semihosting
ARM: 9041/1: sti LL_UART: add STiH418 SBC UART0 support
ARM: 9040/1: use DEBUG_UART_PHYS and DEBUG_UART_VIRT for sti LL_UART
ARM: 9039/1: assembler: generalize byte swapping macro into rev_l
The pointer desc is being null checked twice, the second null check
is redundant because desc has not been re-assigned between the
checks. Remove the redundant second null check on desc.
Fixes: ef6fb2d6f1 ("dmaengine: dw-axi-dmac: simplify descriptor management")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Sia Jee Heng <jee.heng.sia@intel.com>
Reviewed-by: Sia Jee Heng <jee.heng.sia@intel.com>
Addresses-Coverity: ("Logically dead code")
Link: https://lore.kernel.org/r/20210203134652.22618-1-colin.king@canonical.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This reverts commit 842067940a.
For some solutions e.g. sound/soc/intel/catpt, DW DMA is part of a
compound device (in that very example, domains: ADSP, SSP0, SSP1, DMA0
and DMA1 are part of a single entity) rather than being a standalone
one. Driver for said device may enlist DMA to transfer data during
suspend or resume sequences.
Manipulating RPM explicitly in dw's DMA request and release channel
functions causes suspend() to also invoke resume() for the exact same
device. Similar situation occurs for resume() sequence. Effectively
renders device dysfunctional after first suspend() attempt. Revert the
change to address the problem.
Fixes: 842067940a ("dmaengine: dw: Enable runtime PM")
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210203191924.15706-1-cezary.rojewski@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add device state check before executing command. Without the check the
command can be issued while device is in halt state and causes the driver to
block while waiting for the completion of the command.
Reported-by: Sanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Sanjay Kumar <sanjay.k.kumar@intel.com>
Fixes: 0d5c10b4c8 ("dmaengine: idxd: add work queue drain support")
Link: https://lore.kernel.org/r/161219313921.2976211.12222625226450097465.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
All amba drivers return 0 in their remove callback. Together with the
driver core ignoring the return value anyhow, it doesn't make sense to
return a value here.
Change the remove prototype to return void, which makes it explicit that
returning an error value doesn't work as expected. This simplifies changing
the core remove callback to return void, too.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org> # for drivers/memory
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com> # for hwtracing/coresight
Acked-By: Vinod Koul <vkoul@kernel.org> # for dmaengine
Acked-by: Guenter Roeck <linux@roeck-us.net> # for watchdog
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Takashi Iwai <tiwai@suse.de> # for sound
Acked-by: Vladimir Zapolskiy <vz@mleia.com> # for memory/pl172
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210126165835.687514-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Use GFP_NOWAIT allocation in xilinx_dma_alloc_tx_descriptor().
This is necessary for compatibility with ALSA, which calls
dmaengine_prep_dma_cyclic() from an atomic context.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210129170800.31857-1-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
AxiDMA driver exposed the dma_set_max_seg_size() to the DMAENGINE.
It shall helps the DMA clients to create size-optimized linked-list
for the controller.
However, there are certain situations where DMA client might not be
abled to benefit from the dma_get_max_seg_size() if the segment size
can't meet the nature of the DMA client's operation.
In the case of ALSA operation, ALSA application and driver expecting
to run in a period of larger than 10ms regardless of the bit depth.
With this large period, there is a strong request to split the linked-list
in the AxiDMA driver.
Signed-off-by: Sia Jee Heng <jee.heng.sia@intel.com>
Tested-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Link: https://lore.kernel.org/r/20210125013255.25799-18-jee.heng.sia@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for DMA Scatter-Gather (SG) constraint so that DMA clients can
handle the AxiDMA limitation.
Without supporting DMA constraint the default Max segment size reported by
dmaengine is 64KB, which is not supported by Intel KeemBay AxiDMA.
Signed-off-by: Sia Jee Heng <jee.heng.sia@intel.com>
Tested-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Link: https://lore.kernel.org/r/20210125013255.25799-17-jee.heng.sia@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for Intel KeemBay AxiDMA BYTE and HALFWORD registers
programming.
Intel KeemBay AxiDMA supports data transfer between device to memory
and memory to device operations.
This code is needed by I2C, I3C, I2S, SPI and UART which uses FIFO
size of 8bits and 16bits to perform memory to device data transfer
operation. 0-padding functionality is provided to avoid
pre-processing of data on CPU.
Signed-off-by: Sia Jee Heng <jee.heng.sia@intel.com>
Tested-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Link: https://lore.kernel.org/r/20210125013255.25799-16-jee.heng.sia@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for Intel KeemBay AxiDMA device handshake programming.
Device handshake number passed in to the AxiDMA shall be written to
the Intel KeemBay AxiDMA hardware handshake registers before DMA
operations are started.
Signed-off-by: Sia Jee Heng <jee.heng.sia@intel.com>
Tested-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Link: https://lore.kernel.org/r/20210125013255.25799-15-jee.heng.sia@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for Intel KeemBay AxiDMA to the .compatible field.
The AxiDMA Apb region will be accessible if the compatible string
matches the "intel,kmb-axi-dma".
Signed-off-by: Sia Jee Heng <jee.heng.sia@intel.com>
Tested-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Link: https://lore.kernel.org/r/20210125013255.25799-14-jee.heng.sia@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for Intel KeemBay DMA registers. These registers are required
to run data transfer between device to memory and memory to device on Intel
KeemBay SoC.
Signed-off-by: Sia Jee Heng <jee.heng.sia@intel.com>
Tested-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Link: https://lore.kernel.org/r/20210125013255.25799-12-jee.heng.sia@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for DMA_RESIDUE_GRANULARITY_BURST so that AxiDMA can report
DMA residue.
Existing AxiDMA driver only support data transfer between
memory to memory operation, therefore reporting DMA residue
to the DMA clients is not supported.
Reporting DMA residue to the DMA clients is important as DMA clients
shall invoke dmaengine_tx_status() to understand the number of bytes
been transferred so that the buffer pointer can be updated accordingly.
Signed-off-by: Sia Jee Heng <jee.heng.sia@intel.com>
Tested-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Link: https://lore.kernel.org/r/20210125013255.25799-10-jee.heng.sia@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for of_dma_controller_register() so that DMA clients
can pass in device handshake number to the AxiDMA driver.
DMA clients shall code the device handshake number in the Device tree.
When DMA activities are needed, DMA clients shall invoke OF helper
function to pass in the device handshake number to the AxiDMA.
Without register to the of_dma_controller_register(), data transfer
between memory to device and device to memory operations would failed.
Signed-off-by: Sia Jee Heng <jee.heng.sia@intel.com>
Tested-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Link: https://lore.kernel.org/r/20210125013255.25799-9-jee.heng.sia@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for device_prep_dma_cyclic() callback function to benefit
DMA cyclic client, for example ALSA.
Existing AxiDMA driver only support data transfer between memory to memory.
Data transfer between device to memory and memory to device in cyclic mode
would failed if this interface is not supported by the AxiDMA driver.
Signed-off-by: Sia Jee Heng <jee.heng.sia@intel.com>
Tested-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Link: https://lore.kernel.org/r/20210125013255.25799-8-jee.heng.sia@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add device_prep_slave_sg() callback function so that DMA_MEM_TO_DEV
and DMA_DEV_TO_MEM operations in single mode can be supported.
Existing AxiDMA driver only support data transfer between
memory to memory. Data transfer between device to memory and
memory to device in single mode would failed if this interface
is not supported by the AxiDMA driver.
Signed-off-by: Sia Jee Heng <jee.heng.sia@intel.com>
Tested-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Link: https://lore.kernel.org/r/20210125013255.25799-7-jee.heng.sia@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add device_config() callback function so that the device address
can be passed to the dma driver.
DMA clients use this interface to pass in the device address to the
AxiDMA. Without this interface, data transfer between device to memory
and memory to device would failed.
Signed-off-by: Sia Jee Heng <jee.heng.sia@intel.com>
Tested-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Link: https://lore.kernel.org/r/20210125013255.25799-6-jee.heng.sia@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for device_synchronize() callback function to sync with
dmaengine_terminate_sync().
Signed-off-by: Sia Jee Heng <jee.heng.sia@intel.com>
Tested-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Link: https://lore.kernel.org/r/20210125013255.25799-5-jee.heng.sia@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The DMA memory block is created at driver load time and exist for
device lifetime. Move the dma_pool_create() to the ->chan_resource()
callback function allowing the DMA memory blocks to be created as needed
and destroyed when the channel is freed.
Signed-off-by: Sia Jee Heng <jee.heng.sia@intel.com>
Tested-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Link: https://lore.kernel.org/r/20210125013255.25799-4-jee.heng.sia@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Simplify and refactor the descriptor management by removing the redundant
Linked List Item (LLI) queue control logic from the AxiDMA driver.
The descriptor is split into virtual descriptor and hardware LLI so that
only hardware LLI memories are allocated from the DMA memory pool.
Up to 64 descriptors can be allocated within a PAGE_SIZE compare to 16
descriptors in previous version. This solves the problem where an
ALSA driver expects more than 16 DMA descriptors to run.
Signed-off-by: Sia Jee Heng <jee.heng.sia@intel.com>
Tested-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Link: https://lore.kernel.org/r/20210125013255.25799-3-jee.heng.sia@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Intel Lightning Mountain (LGM) DMA controller is only present on
Intel Lightning Mountain SoCs. Hence add a dependency on X86, to
prevent asking the user about this driver when configuring a kernel
without Intel Lightning Mountain platform support.
While at it, fix a misspelling of "Intel".
Fixes: 32d31c79a1 ("dmaengine: Add Intel LGM SoC DMA support.")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210129131702.2656060-1-geert+renesas@glider.be
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The DMACs (both SYS-DMAC and RT-DMAC) on R-Car V3U differ slightly from
the DMACs on R-Car Gen2 and other R-Car Gen3 SoCs:
1. The per-channel registers are located in a second register block.
Add support for mapping the second block, using the appropriate
offsets and stride.
2. The common Channel Clear Register (DMACHCLR) was replaced by a
per-channel register.
Update rcar_dmac_chan_clear{,_all}() to handle this.
As rcar_dmac_init() needs to clear the status before the individual
channels are probed, channel index and base address initialization
are moved forward.
Inspired by a patch in the BSP by Phong Hoang
<phong.hoang.wz@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210128084455.2237256-5-geert+renesas@glider.be
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Extract the code to clear the status of one or all channels into their
own helpers, to prepare for the different handling of the R-Car V3U SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210128084455.2237256-4-geert+renesas@glider.be
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a helper macro for iterating over all DMAC channels, taking into
account the channel mask. Use it where appropriate, to simplify code.
Restore "reverse Christmas tree" order of local variables while adding a
new variable.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210128084455.2237256-3-geert+renesas@glider.be
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When bam dma is "controlled remotely", thus far clocks were not controlled
from the Linux. In this scenario, Linux was disabling runtime pm in bam dma
driver and not doing any clock management in suspend/resume hooks.
With introduction of crypto engine bam dma, the clock is a rpmh resource
that can be controlled from both Linux and TZ/remote side. Now bam dma
clock is getting enabled during probe even though the bam dma can be
"controlled remotely". But due to clocks not being handled properly,
bam_suspend generates a unbalanced clk_unprepare warning during system
suspend.
To fix the above issue and to enable proper clock-management, this patch
enables runtim-pm and handles bam dma clocks in suspend/resume hooks if
the clock node is present irrespective of controlled_remotely property.
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210126211859.790892-1-thara.gopinath@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In 'dma_pool_create()', we return -ENOMEM, but don't release the resources
already allocated, as in all the other error handling paths.
Go to 'err_res_free' instead of returning directly.
Fixes: 0177947397 ("dmaengine: ti: k3-udma: Initial support for K3 BCDMA")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210124070923.724479-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a module parameter that overrides the SVA feature enabling. This keeps
the driver in legacy mode even when intel_iommu=sm_on is set. In this mode,
the descriptor fields must be programmed with dma_addr_t from the Linux DMA
API for source, destination, and completion descriptors.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161134110457.4005461.13171197785259115852.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The zte zx platform is getting removed, so this driver is no
longer needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Link: https://lore.kernel.org/r/20210120131859.2056308-3-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The CSR SiRF prima2/atlas platforms are getting removed, so this driver
is no longer needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Barry Song <baohua@kernel.org>
Cc: Barry Song <baohua@kernel.org>
Link: https://lore.kernel.org/r/20210120131859.2056308-2-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for the JZ4760 and JZ4760B SoCs.
Both SoCs have only 5 DMA channels per chip. The JZ4760B introduced the
DCKES/DCKEC registers.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210120105322.16116-2-paul@crapouillou.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since 5.10-rc1, i.MX has been converted to a devicetree-only platform.
The platform data support in this driver was only used for non-DT
platforms.
Remove the platform data support as it has no more users.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210118121549.1625217-1-festevam@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Dave Jiang