This adds the infrastructure to enable us to page out pages underneath
a Book3S HV guest, on processors that support virtualized partition
memory, that is, POWER7. Instead of pinning all the guest's pages,
we now look in the host userspace Linux page tables to find the
mapping for a given guest page. Then, if the userspace Linux PTE
gets invalidated, kvm_unmap_hva() gets called for that address, and
we replace all the guest HPTEs that refer to that page with absent
HPTEs, i.e. ones with the valid bit clear and the HPTE_V_ABSENT bit
set, which will cause an HDSI when the guest tries to access them.
Finally, the page fault handler is extended to reinstantiate the
guest HPTE when the guest tries to access a page which has been paged
out.
Since we can't intercept the guest DSI and ISI interrupts on PPC970,
we still have to pin all the guest pages on PPC970. We have a new flag,
kvm->arch.using_mmu_notifiers, that indicates whether we can page
guest pages out. If it is not set, the MMU notifier callbacks do
nothing and everything operates as before.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This provides the low-level support for MMIO emulation in Book3S HV
guests. When the guest tries to map a page which is not covered by
any memslot, that page is taken to be an MMIO emulation page. Instead
of inserting a valid HPTE, we insert an HPTE that has the valid bit
clear but another hypervisor software-use bit set, which we call
HPTE_V_ABSENT, to indicate that this is an absent page. An
absent page is treated much like a valid page as far as guest hcalls
(H_ENTER, H_REMOVE, H_READ etc.) are concerned, except of course that
an absent HPTE doesn't need to be invalidated with tlbie since it
was never valid as far as the hardware is concerned.
When the guest accesses a page for which there is an absent HPTE, it
will take a hypervisor data storage interrupt (HDSI) since we now set
the VPM1 bit in the LPCR. Our HDSI handler for HPTE-not-present faults
looks up the hash table and if it finds an absent HPTE mapping the
requested virtual address, will switch to kernel mode and handle the
fault in kvmppc_book3s_hv_page_fault(), which at present just calls
kvmppc_hv_emulate_mmio() to set up the MMIO emulation.
This is based on an earlier patch by Benjamin Herrenschmidt, but since
heavily reworked.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This expands the reverse mapping array to contain two links for each
HPTE which are used to link together HPTEs that correspond to the
same guest logical page. Each circular list of HPTEs is pointed to
by the rmap array entry for the guest logical page, pointed to by
the relevant memslot. Links are 32-bit HPT entry indexes rather than
full 64-bit pointers, to save space. We use 3 of the remaining 32
bits in the rmap array entries as a lock bit, a referenced bit and
a present bit (the present bit is needed since HPTE index 0 is valid).
The bit lock for the rmap chain nests inside the HPTE lock bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This provides for the case where userspace maps an I/O device into the
address range of a memory slot using a VM_PFNMAP mapping. In that
case, we work out the pfn from vma->vm_pgoff, and record the cache
enable bits from vma->vm_page_prot in two low-order bits in the
slot_phys array entries. Then, in kvmppc_h_enter() we check that the
cache bits in the HPTE that the guest wants to insert match the cache
bits in the slot_phys array entry. However, we do allow the guest to
create what it thinks is a non-cacheable or write-through mapping to
memory that is actually cacheable, so that we can use normal system
memory as part of an emulated device later on. In that case the actual
HPTE we insert is a cacheable HPTE.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This relaxes the requirement that the guest memory be provided as
16MB huge pages, allowing it to be provided as normal memory, i.e.
in pages of PAGE_SIZE bytes (4k or 64k). To allow this, we index
the kvm->arch.slot_phys[] arrays with a small page index, even if
huge pages are being used, and use the low-order 5 bits of each
entry to store the order of the enclosing page with respect to
normal pages, i.e. log_2(enclosing_page_size / PAGE_SIZE).
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This removes the code from kvmppc_core_prepare_memory_region() that
looked up the VMA for the region being added and called hva_to_page
to get the pfns for the memory. We have no guarantee that there will
be anything mapped there at the time of the KVM_SET_USER_MEMORY_REGION
ioctl call; userspace can do that ioctl and then map memory into the
region later.
Instead we defer looking up the pfn for each memory page until it is
needed, which generally means when the guest does an H_ENTER hcall on
the page. Since we can't call get_user_pages in real mode, if we don't
already have the pfn for the page, kvmppc_h_enter() will return
H_TOO_HARD and we then call kvmppc_virtmode_h_enter() once we get back
to kernel context. That calls kvmppc_get_guest_page() to get the pfn
for the page, and then calls back to kvmppc_h_enter() to redo the HPTE
insertion.
When the first vcpu starts executing, we need to have the RMO or VRMA
region mapped so that the guest's real mode accesses will work. Thus
we now have a check in kvmppc_vcpu_run() to see if the RMO/VRMA is set
up and if not, call kvmppc_hv_setup_rma(). It checks if the memslot
starting at guest physical 0 now has RMO memory mapped there; if so it
sets it up for the guest, otherwise on POWER7 it sets up the VRMA.
The function that does that, kvmppc_map_vrma, is now a bit simpler,
as it calls kvmppc_virtmode_h_enter instead of creating the HPTE itself.
Since we are now potentially updating entries in the slot_phys[]
arrays from multiple vcpu threads, we now have a spinlock protecting
those updates to ensure that we don't lose track of any references
to pages.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
At present, our implementation of H_ENTER only makes one try at locking
each slot that it looks at, and doesn't even retry the ldarx/stdcx.
atomic update sequence that it uses to attempt to lock the slot. Thus
it can return the H_PTEG_FULL error unnecessarily, particularly when
the H_EXACT flag is set, meaning that the caller wants a specific PTEG
slot.
This improves the situation by making a second pass when no free HPTE
slot is found, where we spin until we succeed in locking each slot in
turn and then check whether it is full while we hold the lock. If the
second pass fails, then we return H_PTEG_FULL.
This also moves lock_hpte to a header file (since later commits in this
series will need to use it from other source files) and renames it to
try_lock_hpte, which is a somewhat less misleading name.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This adds two new functions, kvmppc_pin_guest_page() and
kvmppc_unpin_guest_page(), and uses them to pin the guest pages where
the guest has registered areas of memory for the hypervisor to update,
(i.e. the per-cpu virtual processor areas, SLB shadow buffers and
dispatch trace logs) and then unpin them when they are no longer
required.
Although it is not strictly necessary to pin the pages at this point,
since all guest pages are already pinned, later commits in this series
will mean that guest pages aren't all pinned.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This allocates an array for each memory slot that is added to store
the physical addresses of the pages in the slot. This array is
vmalloc'd and accessed in kvmppc_h_enter using real_vmalloc_addr().
This allows us to remove the ram_pginfo field from the kvm_arch
struct, and removes the 64GB guest RAM limit that we had.
We use the low-order bits of the array entries to store a flag
indicating that we have done get_page on the corresponding page,
and therefore need to call put_page when we are finished with the
page. Currently this is set for all pages except those in our
special RMO regions.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This adds an array that parallels the guest hashed page table (HPT),
that is, it has one entry per HPTE, used to store the guest's view
of the second doubleword of the corresponding HPTE. The first
doubleword in the HPTE is the same as the guest's idea of it, so we
don't need to store a copy, but the second doubleword in the HPTE has
the real page number rather than the guest's logical page number.
This allows us to remove the back_translate() and reverse_xlate()
functions.
This "reverse mapping" array is vmalloc'd, meaning that to access it
in real mode we have to walk the kernel's page tables explicitly.
That is done by the new real_vmalloc_addr() function. (In fact this
returns an address in the linear mapping, so the result is usable
both in real mode and in virtual mode.)
There are also some minor cleanups here: moving the definitions of
HPT_ORDER etc. to a header file and defining HPT_NPTE for HPT_NPTEG << 3.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
When commit f43fdc15fa ("KVM: PPC: booke: Improve timer register
emulation") factored out some code in arch/powerpc/kvm/powerpc.c
into a new helper function, kvm_vcpu_kick(), an error crept in
which causes Book3s HV guest vcpus to stall. This fixes it.
On POWER7 machines, guest vcpus are grouped together into virtual
CPU cores that share a single waitqueue, so it's important to use
vcpu->arch.wqp rather than &vcpu->wq.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently we patch the whole code include paravirt template code.
This isn't safe for scratch area and has impact to performance.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The hardware maintains a per-set next victim hint. Using this
reduces conflicts, especially on e500v2 where a single guest
TLB entry is mapped to two shadow TLB entries (user and kernel).
We want those two entries to go to different TLB ways.
sesel is now only used for TLB1.
Reported-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The associativity, not just total size, can differ from the host
hardware.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
As Scott put it:
> If we get a signal after the check, we want to be sure that we don't
> receive the reschedule IPI until after we're in the guest, so that it
> will cause another signal check.
we need to have interrupts disabled from the point we do signal_check()
all the way until we actually enter the guest.
This patch fixes potential signal loss races.
Reported-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Our vcpu kick implementation differs a bit from x86 which resulted in us not
disabling preemption during the kick. Get it a bit closer to what x86 does.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
When running the 64-bit Book3s PR code without CONFIG_PREEMPT_NONE, we were
doing a few things wrong, most notably access to PACA fields without making
sure that the pointers stay stable accross the access (preempt_disable()).
This patch moves to_svcpu towards a get/put model which allows us to disable
preemption while accessing the shadow vcpu fields in the PACA. That way we
can run preemptible and everyone's happy!
Reported-by: Jörg Sommer <joerg@alea.gnuu.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Somewhere during merges we ended up from
local_irq_enable()
foo();
local_irq_disable()
to always keeping irqs enabled during that part. However, we now
have the following code:
foo();
local_irq_disable()
which disables interrupts without the surrounding code enabling them
again! So let's remove that disable and be happy.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
When entering the guest, we want to make sure we're not getting preempted
away, so let's disable preemption on entry, but enable it again while handling
guest exits.
Reported-by: Jörg Sommer <joerg@alea.gnuu.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Decrementers are now properly driven by TCR/TSR, and the guest
has full read/write access to these registers.
The decrementer keeps ticking (and setting the TSR bit) regardless of
whether the interrupts are enabled with TCR.
The decrementer stops at zero, rather than going negative.
Decrementers (and FITs, once implemented) are delivered as
level-triggered interrupts -- dequeued when the TSR bit is cleared, not
on delivery.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
[scottwood@freescale.com: significant changes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This allows additional registers to be accessed by the guest
in PR-mode KVM without trapping.
SPRG4-7 are readable from userspace. On booke, KVM will sync
these registers when it enters the guest, so that accesses from
guest userspace will work. The guest kernel, OTOH, must consistently
use either the real registers or the shared area between exits. This
also applies to the already-paravirted SPRG3.
On non-booke, it's not clear to what extent SPRG4-7 are supported
(they're not architected for book3s, but exist on at least some classic
chips). They are copied in the get/set regs ioctls, but I do not see any
non-booke emulation. I also do not see any syncing with real registers
(in PR-mode) including the user-readable SPRG3. This patch should not
make that situation any worse.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Also fix wrteei 1 paravirt to check for a pending interrupt.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
int_pending was only being lowered if a bit in pending_exceptions
was cleared during exception delivery -- but for interrupts, we clear
it during IACK/TSR emulation. This caused paravirt for enabling
MSR[EE] to be ineffective.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This prevents us from inappropriately blocking in a KVM_SET_REGS
ioctl -- the MSR[WE] will take effect when the guest is next entered.
It also causes SRR1[WE] to be set when we enter the guest's interrupt
handler, which is what e500 hardware is documented to do.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This function should be called with interrupts disabled, to avoid
a race where an exception is delivered after we check, but the
resched kick is received before we disable interrupts (and thus doesn't
actually trigger the exit code that would recheck exceptions).
booke already does this properly in the lightweight exit case, but
not on initial entry.
For now, move the call of prepare_to_enter into subarch-specific code so
that booke can do the right thing here. Ideally book3s would do the same
thing, but I'm having a hard time seeing where it does any interrupt
disabling of this sort (plus it has several additional call sites), so
I'm deferring the book3s fix to someone more familiar with that code.
book3s behavior should be unchanged by this patch.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This function also updates paravirt int_pending, so rename it
to be more obvious that this is a collection of checks run prior
to (re)entering a guest.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently we check prior to returning from a lightweight exit,
but not prior to initial entry.
book3s already does a similar test.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
As per specification the decrementer interrupt not happen when DEC is written
with 0. Also when DEC is zero, no decrementer running. So we should not start
hrtimer for decrementer when DEC = 0.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
kvmppc_emulate_dec() uses dec_nsec of type unsigned long and does below calculation:
dec_nsec = vcpu->arch.dec;
dec_nsec *= 1000;
This will truncate if DEC value "vcpu->arch.dec" is greater than 0xffff_ffff/1000.
For example : For tb_ticks_per_usec = 4a, we can not set decrementer more than ~58ms.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Acked-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The current implementation of mtmsr and mtmsrd are racy in that it does:
* check (int_pending == 0)
---> host sets int_pending = 1 <---
* write shared page
* done
while instead we should check for int_pending after the shared page is written.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
With hugetlbfs support emerging on e500, we should also support KVM
backing its guest memory by it.
This patch adds support for hugetlbfs into the e500 shadow mmu code.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The hardcoded behavior prevents proper SMP support.
user space shall specify the vcpu's PIR as the vcpu id.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
It should contain the way, not the absolute TLB0 index.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This implements a shared-memory API for giving host userspace access to
the guest's TLB.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Split out the portions of tlbe_priv that should be associated with host
entries into tlbe_ref. Base victim selection on the number of hardware
entries, not guest entries.
For TLB1, where one guest entry can be mapped by multiple host entries,
we use the host tlbe_ref for tracking page references. For the guest
TLB0 entries, we still track it with gtlb_priv, to avoid having to
retranslate if the entry is evicted from the host TLB but not the
guest TLB.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The only place it makes sense to call this function already needs
to have preemption disabled.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Delay allocation of the shadow pid until we're ready to disable
preemption and write the entry.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
On some cpus the overhead for virtualization instructions is in the same
range as a system call. Having to call multiple ioctls to get set registers
will make certain userspace handled exits more expensive than necessary.
Lets provide a section in kvm_run that works as a shared save area
for guest registers.
We also provide two 64bit flags fields (architecture specific), that will
specify
1. which parts of these fields are valid.
2. which registers were modified by userspace
Each bit for these flag fields will define a group of registers (like
general purpose) or a single register.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch exports the s390 SIE hardware control block to userspace
via the mapping of the vcpu file descriptor. In order to do so,
a new arch callback named kvm_arch_vcpu_fault is introduced for all
architectures. It allows to map architecture specific pages.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch introduces a new config option for user controlled kernel
virtual machines. It introduces a parameter to KVM_CREATE_VM that
allows to set bits that alter the capabilities of the newly created
virtual machine.
The parameter is passed to kvm_arch_init_vm for all architectures.
The only valid modifier bit for now is KVM_VM_S390_UCONTROL.
This requires CAP_SYS_ADMIN privileges and creates a user controlled
virtual machine on s390 architectures.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Create a distinction between scheduler related preempt_enable_no_resched()
calls and the nearly one hundred other places in the kernel that do not
want to reschedule, for one reason or another.
This distinction matters for -rt, where the scheduler and the non-scheduler
preempt models (and checks) are different. For upstream it's purely
documentational.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/n/tip-gs88fvx2mdv5psnzxnv575ke@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With bug.h currently living right in linux/kernel.h there
are files that use BUG_ON and friends but are not including
the header explicitly. Fix them up so we can remove the
presence in kernel.h file.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The old pci_remove_bus_device actually did stop and remove.
Make the name reflect that to reduce confusion.
This patch is done by sed scripts and changes back some incorrect
__pci_remove_bus_device changes.
Suggested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Conflicts:
drivers/net/ethernet/sfc/rx.c
Overlapping changes in drivers/net/ethernet/sfc/rx.c, one to change
the rx_buf->is_page boolean into a set of u16 flags, and another to
adjust how ->ip_summed is initialized.
Signed-off-by: David S. Miller <davem@davemloft.net>
arch/powerpc/platforms/powernv/setup.c: included 'asm/xics.h' twice,
remove the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/kvm/book3s_hv.c: included 'linux/sched.h' twice,
remove the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
After this, we can remove the legacy iSeries code more easily.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When using a multi-ISU MPIC, we can interrupts up to
isu_size * MPIC_MAX_ISU, not just isu_size, so allocate
the right size reverse map.
Without this, the code will constantly fallback to
a linear search.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is useful for testing RX handling of frames with bad
CRCs.
Requires driver support to actually put the packet on the
wire properly.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
So here's a boot tested patch on top of Jason's series that does
all the cleanups I talked about and turns jump labels into a
more intuitive to use facility. It should also address the
various misconceptions and confusions that surround jump labels.
Typical usage scenarios:
#include <linux/static_key.h>
struct static_key key = STATIC_KEY_INIT_TRUE;
if (static_key_false(&key))
do unlikely code
else
do likely code
Or:
if (static_key_true(&key))
do likely code
else
do unlikely code
The static key is modified via:
static_key_slow_inc(&key);
...
static_key_slow_dec(&key);
The 'slow' prefix makes it abundantly clear that this is an
expensive operation.
I've updated all in-kernel code to use this everywhere. Note
that I (intentionally) have not pushed through the rename
blindly through to the lowest levels: the actual jump-label
patching arch facility should be named like that, so we want to
decouple jump labels from the static-key facility a bit.
On non-jump-label enabled architectures static keys default to
likely()/unlikely() branches.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jason Baron <jbaron@redhat.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: a.p.zijlstra@chello.nl
Cc: mathieu.desnoyers@efficios.com
Cc: davem@davemloft.net
Cc: ddaney.cavm@gmail.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20120222085809.GA26397@elte.hu
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Everybody uses the generic pcibios_resource_to_bus() supplied by the core
now, so remove the ARCH_HAS_GENERIC_PCI_OFFSETS used during conversion.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We already use pci_flags, so this just sets pci_flags directly and removes
the intermediate step of figuring out pci_probe_only, then using it to set
pci_flags.
The PCI core provides a pci_flags definition (currently __weak), so drop
the powerpc definitions in favor of that.
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_probe_only is set on ppc64 to prevent resource re-allocation
by the core. It's meant to be used in very specific circumstances
such as when operating under a hypervisor that may prevent such
re-allocation.
Instead of default to 1, we make it default to 0 and explicitly
set it in the few cases where we need it.
This fixes FSL PCI which wants it clear among others.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The commit bae1d8f199 (linux-next)
"irq_domain/powerpc: Use common irq_domain structure instead of irq_host"
made this change:
-static struct irq_host *flipper_irq_host;
+static struct irq_domain *flipper_irq_host;
and this change:
-static struct irq_host *hlwd_irq_host;
+static struct irq_domain *hlwd_irq_host;
The intent was to change the type, and not the name, but then in a
couple of instances, it looks like the sed to change the irq_domain_ops
name inadvertently also changed the irq_host name where it was not
supposed to, causing build failures.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The perf code has grown a lot since it started, and is big enough to
warrant its own subdirectory. For reference it's ~60% bigger than the
oprofile code. It declutters the kernel directory, makes it simpler to
grep for "just perf stuff", and allows us to shorten some filenames.
While we're at it, make it more obvious that we have two implementations
of the core perf logic. One for (roughly) Book3S CPUs, which was the
original implementation, and the other for Freescale embedded CPUs.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove the phyp assisted dump implementation which is not is use.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If dump is active during system reboot, shutdown or halt then invalidate
the fadump registration as it does not get invalidated automatically.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch introduces an sysfs interface '/sys/kernel/fadump_release_mem' to
invalidate the last fadump registration, invalidate '/proc/vmcore', release
the reserved memory for general use and re-register for future kernel dump.
Once the dump is copied to the disk, unlike phyp dump, the userspace tool
can release all the memory reserved for dump with one single operation of
echo 1 to '/sys/kernel/fadump_release_mem'.
Release the reserved memory region excluding the size of the memory required
for future kernel dump registration. And therefore, unlike kdump, Fadump
doesn't need a 2nd reboot to get back the system to the production
configuration.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Introduce a PT_NOTE program header that points to physical address of
vmcoreinfo_note buffer declared in kernel/kexec.c. The vmcoreinfo
note buffer is populated during crash_fadump() at the time of system
crash.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When registered for firmware assisted dump on powerpc, firmware preserves
the registers for the active CPUs during a system crash. This patch reads
the cpu register data stored in Firmware-assisted dump format (except for
crashing cpu) and converts it into elf notes and updates the PT_NOTE program
header accordingly. The exact register state for crashing cpu is saved to
fadump crash info structure in scratch area during crash_fadump() and read
during second kernel boot.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Build the crash memory range list by traversing through system memory during
the first kernel before we register for firmware-assisted dump. After the
successful dump registration, initialize the elfcore header and populate
PT_LOAD program headers with crash memory ranges. The elfcore header is
saved in the scratch area within the reserved memory. The scratch area starts
at the end of the memory reserved for saving RMR region contents. The
scratch area contains fadump crash info structure that contains magic number
for fadump validation and physical address where the eflcore header can be
found. This structure will also be used to pass some important crash info
data to the second kernel which will help second kernel to populate ELF core
header with correct data before it gets exported through /proc/vmcore. Since
the firmware preserves the entire partition memory at the time of crash the
contents of the scratch area will be preserved till second kernel boot.
Since the memory dump exported through /proc/vmcore is in ELF format similar
to kdump, it will help us to reuse the kdump infrastructure for dump capture
and filtering. Unlike phyp dump, userspace tool does not need to refer any
sysfs interface while reading /proc/vmcore.
NOTE: The current design implementation does not address a possibility of
introducing additional fields (in future) to this structure without affecting
compatibility. It's on TODO list to come up with better approach to
address this.
Reserved dump area start => +-------------------------------------+
| CPU state dump data |
+-------------------------------------+
| HPTE region data |
+-------------------------------------+
| RMR region data |
Scratch area start => +-------------------------------------+
| fadump crash info structure { |
| magic nummber |
+------|---- elfcorehdr_addr |
| | } |
+----> +-------------------------------------+
| ELF core header |
Reserved dump area end => +-------------------------------------+
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On 2012-02-20 11:02:51 Mon, Paul Mackerras wrote:
> On Thu, Feb 16, 2012 at 04:44:30PM +0530, Mahesh J Salgaonkar wrote:
>
> If I have read the code correctly, we are going to get this printk on
> non-pSeries machines or on older pSeries machines, even if the user
> has not put the fadump=on option on the kernel command line. The
> printk will be annoying since there is no actual error condition. It
> seems to me that the condition for the printk should include
> fw_dump.fadump_enabled. In other words you should probably add
>
> if (!fw_dump.fadump_enabled)
> return 0;
>
> at the beginning of the function.
Hi Paul,
Thanks for pointing it out. Please find the updated patch below.
The existing patches above this (4/10 through 10/10) cleanly applies
on this update.
Thanks,
-Mahesh.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reserve the memory during early boot to preserve CPU state data, HPTE region
and RMA (real mode area) region data in case of kernel crash. At the time of
crash, powerpc firmware will store CPU state data, HPTE region data and move
RMA region data to the reserved memory area.
If the firmware-assisted dump fails to reserve the memory, then fallback
to existing kexec-based kdump.
Most of the code implementation to reserve memory has been
adapted from phyp assisted dump implementation written by Linas Vepstas
and Manish Ahuja
This patch also introduces a config option CONFIG_FA_DUMP for firmware
assisted dump feature on Powerpc (ppc64) architecture.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are two separate flags controlling whether or not the MPIC is
reset during initialization, which is completely unnecessary, and only
one of them can be specified in the device tree.
Also, most platforms in-tree right now do actually want to reset the
MPIC during initialization anyways, which means lots of duplicate code
passing the MPIC_WANTS_RESET flag.
Fix all of the callers which currently do not pass the MPIC_WANTS_RESET
flag to pass the MPIC_NO_RESET flag, then remove the MPIC_WANTS_RESET
flag and make the code reset the MPIC by default.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The FreeScale PowerQUICC-III-compatible (mpc85xx/mpc86xx) MPICs do not
correctly report the number of hardware interrupt sources, so software
needs to override the detected value with "256".
To avoid needing to write custom board-specific code to detect that
scenario, allow it to be easily overridden in the device-tree.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The mpic->irq_count variable is only used as a software error-checking
limit to determine whether or not an IRQ number is valid. In board code
which does not manually specify an IRQ count to mpic_alloc(), i.e. 0, it
is automatically detected from the number of ISUs and the ISU size.
In practice, all hardware ends up with irq_count == num_sources, so all
of the runtime checks on mpic->irq_count should just check the value of
mpic->num_sources instead.
When platform hardware does not correctly report the number of IRQs,
which only happens on the MPC85xx/MPC86xx, the MPIC_BROKEN_FRR_NIRQS
flag is used to override the detected value of num_sources with the
manual irq_count parameter. Since there's no need to manually specify
the number of IRQs except in this case, the extra flag can be eliminated
and the test changed to "irq_count != 0".
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Freescale MPIC (and perhaps others in the future) is incapable of
routing non-IPI interrupts to more than once CPU at a time. Currently
all of the Freescale boards msut pass the MPIC_SINGLE_DEST_CPU flag to
mpic_alloc(), but that information should really be present in the
device-tree.
Older board code can't rely on the device-tree having the property set,
but newer platforms won't need it manually specified in the code.
[BenH: Remove unrelated changes, folded in a different patch]
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The MPIC code checks for a "big-endian" property and sets the flag
MPIC_BIG_ENDIAN if one is present, although prior to the "mpic->flags"
fixup that would never have worked anways.
Unfortunately, even now that it works properly, the Freescale mpic
device-node (the "PowerQUICC-III"-compatible one) does not specify it,
so all of the board ports need to manually pass it to mpic_alloc().
Document the flag and add it to the pq3 device tree. Existing code will
still need to pass the MPIC_BIG_ENDIAN flag because their dtb may not
have this property, but new platforms shouldn't need to do so.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The mpic_alloc() function takes a "flags" parameter and assigns it into
the mpic->flags variable fairly early on, but several later pieces of
code detect various device-tree properties and save them into the
"mpic->flags" variable (EG: "big-endian" => MPIC_BIG_ENDIAN).
Unfortunately, a number of codepaths (including several which test the
flag MPIC_BIG_ENDIAN!) test "flags" instead of "mpic->flags", and get
wrong answers as a result.
Consolidate the device-tree flag tests early in mpic_alloc() and change
all of the checks after "mpic->flags" is init'ed to use "mpic->flags".
[BenH: Fixed up use of mpic->node before it's initialized]
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have a few problems when returning to userspace. This is a
quick set of fixes for 3.3, I'll look into a more comprehensive
rework for 3.4. This fixes:
- We kept interrupts soft-disabled when schedule'ing or calling
do_signal when returning to userspace as a result of a hardware
interrupt.
- Rename do_signal to do_notify_resume like all other archs (and
do_signal_pending back to do_signal, which it was before Roland
changed it).
- Add the missing call to key_replace_session_keyring() to
do_notify_resume().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
In commit 54321242af ("Disable interrupts early in Program Check"), we
switched from enabling to disabling interrupts in program_check_common.
Whereas ENABLE_INTS leaves r3 untouched, if lockdep is enabled DISABLE_INTS
calls into lockdep code and will clobber r3. That means we pass a bogus
struct pt_regs* into program_check_exception() and all hell breaks loose.
So load our regs pointer into r3 after we call DISABLE_INTS.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This has been obsolescent for a while; time for the final push.
In adjacent context, replaced old cpus_* with cpumask_*.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Only two architectures use the OF node reference counting and reclaim bits.
There is no need to compile it for the rest of the PowerPC platforms or for
any of the other architectures. This patch makes iseries and pseries
select CONFIG_OF_DYNAMIC, and makes it default to off for everything else.
It is still safe to turn on CONFIG_OF_DYNAMIC on all architectures, it just
isn't necessary.
v2: Also select OF_DYNAMIC for PPC_CHROMA and MPC885ADS as reported by Michael
Meuling
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jimi Xenidis <jimix@pobox.com> (for PPC_CHROMA bug fix)
Cc: Rob Herring <rob.herring@calxeda.com>
This one specifies where to start MSG_PEEK-ing queue data from. When
set to negative value means that MSG_PEEK works as ususally -- peeks
from the head of the queue always.
When some bytes are peeked from queue and the peeking offset is non
negative it is moved forward so that the next peek will return next
portion of data.
When non-peeking recvmsg occurs and the peeking offset is non negative
is is moved backward so that the next peek will still peek the proper
data (i.e. the one that would have been picked if there were no non
peeking recv in between).
The offset is set using per-proto opteration to let the protocol handle
the locking issues and to check whether the peeking offset feature is
supported by the protocol the socket belongs to.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The below patch fixes some typos "aditional" to "additional", and also fixes
a comment with another word mispelled.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Wrap accesses to the fd_sets in struct fdtable (for recording open files and
close-on-exec flags) so that we can move away from using fd_sets since we
abuse the fd_set structs by not allocating the full-sized structure under
normal circumstances and by non-core code looking at the internals of the
fd_sets.
The first abuse means that use of FD_ZERO() on these fd_sets is not permitted,
since that cannot be told about their abnormal lengths.
This introduces six wrapper functions for setting, clearing and testing
close-on-exec flags and fd-is-open flags:
void __set_close_on_exec(int fd, struct fdtable *fdt);
void __clear_close_on_exec(int fd, struct fdtable *fdt);
bool close_on_exec(int fd, const struct fdtable *fdt);
void __set_open_fd(int fd, struct fdtable *fdt);
void __clear_open_fd(int fd, struct fdtable *fdt);
bool fd_is_open(int fd, const struct fdtable *fdt);
Note that I've prepended '__' to the names of the set/clear functions because
they require the caller to hold a lock to use them.
Note also that I haven't added wrappers for looking behind the scenes at the
the array. Possibly that should exist too.
Signed-off-by: David Howells <dhowells@redhat.com>
Link: http://lkml.kernel.org/r/20120216174942.23314.1364.stgit@warthog.procyon.org.uk
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
This patch converts a number of the powerpc drivers to use the common library
of irq_domain xlate functions, dropping a bunch of lines in the process.
v5: - Remove tsi108 changes from patch
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
Make all the irq_domain_ops structures in powerpc 'static const'
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
Make irq_domain_ops pointer a constant to make it safer for multiple
instances to share the same ops pointer and change the irq_domain code
so that it does not modify the ops.
v4: Fix mismatched type reference in powerpc code
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
Add support for a legacy mapping where irq = (hwirq - first_hwirq + first_irq)
so that a controller driver can allocate a fixed range of irq_descs and use
a simple calculation to translate back and forth between linux and hw irq
numbers. This is needed to use an irq_domain with many of the ARM interrupt
controller drivers that manage their own irq_desc allocations. Ultimately
the goal is to migrate those drivers to use the linear revmap, but doing it
this way allows each driver to be converted separately which makes the
migration path easier.
This patch generalizes the IRQ_DOMAIN_MAP_LEGACY method to use
(first_irq-first_hwirq) as the offset between hwirq and linux irq number,
and adds checks to make sure that the hwirq number does not exceed range
assigned to the controller.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
Each revmap type has different arguments for setting up the revmap.
This patch splits up the generator functions so that each revmap type
can do its own setup and the user doesn't need to keep track of how
each revmap type handles the arguments.
This patch also adds a host_data argument to the generators. There are
cases where the host_data pointer will be needed before the function returns.
ie. the legacy map calls the .map callback for each irq before returning.
v2: - Add void *host_data argument to irq_domain_add_*() functions
- fixed failure to compile
- Moved IRQ_DOMAIN_MAP_* defines into irqdomain.c
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
This patch only moves the code. It doesn't make any changes, and the
code is still only compiled for powerpc. Follow-on patches will generalize
the code for other architectures.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
There is only one user, and it is trivial to open-code.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
perf on POWER stopped working after commit e050e3f0a7 (perf: Fix
broken interrupt rate throttling). That patch exposed a bug in
the POWER perf_events code.
Since the PMCs count upwards and take an exception when the top bit
is set, we want to write 0x80000000 - left in power_pmu_start. We were
instead programming in left which effectively disables the counter
until we eventually hit 0x80000000. This could take seconds or longer.
With the patch applied I get the expected number of samples:
SAMPLE events: 9948
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@kernel.org>
Program Check exceptions are the result of WARNs, BUGs, some
type of breakpoints, kprobe, and other illegal instructions.
We want interrupts (and thus preemption) to remain disabled
while doing the initial stage of testing the reason and
branching off to a debugger or kprobe, so we are still on
the original CPU which makes debugging easier in various cases.
This is how the code was intended, hence the local_irq_enable()
right in the middle of program_check_exception().
However, the assembly exception prologue for that exception was
incorrectly marked as enabling interrupts, which defeats that
(and records a redundant enable with lockdep).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since we are heading towards removing the Legacy iSeries platform, start
by no longer building it for ppc64_defconfig.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Upstream changes to the way PHB resources are registered
broke the resource fixup for FSL boards.
We can no longer rely on the resource pointer array for the PHB's
pci_bus structure, so let's leave it alone and go straight for
the PHB resources instead. This also makes the code generally
more readable.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A kernel oops/panic prints an instruction dump showing several
instructions before and after the instruction which caused the
oops/panic.
The code intended that the faulting instruction be enclosed in angle
brackets, however a bug caused the faulting instruction to be
interpreted by printk() as the message log level.
To fix this, the KERN_CONT log level is added before the actual text of
the printed message.
=== Before the patch ===
[ 1081.587266] Instruction dump:
[ 1081.590236] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
[ 1081.598034] 3d20c03a 9009a114 7c0004ac 39200000
[ 1081.602500] 4e800020 3803ffd0 2b800009
<4>[ 1081.587266] Instruction dump:
<4>[ 1081.590236] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
<4>[ 1081.598034] 3d20c03a 9009a114 7c0004ac 39200000
<98090000>[ 1081.602500] 4e800020 3803ffd0 2b800009
=== After the patch ===
[ 51.385216] Instruction dump:
[ 51.388186] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
[ 51.395986] 3d20c03a 9009a114 7c0004ac 39200000 <98090000> 4e800020 3803ffd0 2b800009
<4>[ 51.385216] Instruction dump:
<4>[ 51.388186] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
<4>[ 51.395986] 3d20c03a 9009a114 7c0004ac 39200000 <98090000> 4e800020 3803ffd0 2b800009
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch drops the powerpc-specific irq_map table and replaces it with
directly using the irq_alloc_desc()/irq_free_desc() interfaces for allocating
and freeing irq_desc structures.
This patch is a preparation step for generalizing the powerpc-specific virq
infrastructure to become irq_domains.
As part of this change, the irq_big_lock is changed to a mutex from a raw
spinlock. There is no longer any need to use a spin lock since the irq_desc
allocation code is now responsible for the critical section of finding
an unused range of irq numbers.
The radix lookup table is also changed to store the irq_data pointer instead
of the irq_map entry since the irq_map is removed. This should end up being
functionally equivalent since only allocated irq_descs are ever added to the
radix tree.
v5: - Really don't ever allocate virq 0. The previous version could still
do it if hint == 0
- Respect irq_virq_count setting for NOMAP. Some NOMAP domains cannot
use virq values above irq_virq_count.
- Use numa_node_id() when allocating irq_descs. Ideally the API should
obtain that value from the caller, but that touches a lot of call sites
so will be deferred to a follow-on patch.
- Fix irq_find_mapping() to include irq numbers lower than
NUM_ISA_INTERRUPTS. With the switch to irq_alloc_desc*(), the lowest
possible allocated irq is now returned by arch_probe_nr_irqs().
v4: - Fix incorrect access to irq_data structure in debugfs code
- Don't ever allocate virq 0
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
This patch drops the powerpc-specific irq_host structures and uses the common
irq_domain strucutres defined in linux/irqdomain.h. It also fixes all
the users to use the new structure names.
Renaming irq_host to irq_domain has been discussed for a long time, and this
patch is a step in the process of generalizing the powerpc virq code to be
usable by all architecture.
An astute reader will notice that this patch actually removes the irq_host
structure instead of renaming it. This is because the irq_domain structure
already exists in include/linux/irqdomain.h and has the needed data members.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
Change the powerpc architecture to use <asm-generic/posix_types.h>.
[ v2: fix the definition for __kernel_ssize_t ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1328677745-20121-16-git-send-email-hpa@zytor.com
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
EEH may happen during a PCI driver probe. If the driver is trying to
access some register in a loop, the EEH code will try to print the
driver name. But the driver pointer in struct pci_dev is not set until
probe returns successfully.
Use a function to test if the device and the driver pointer is NULL
before accessing the driver's name.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to disable interrupts when taking the phb->lock. Otherwise
we could deadlock with pci_lock taken from an interrupt.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We use __get_cpu_var() which triggers a false positive warning
in smp_processor_id() thinking interrupts are enabled (at this
point, they are soft-enabled but hard-disabled).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We call the cache_hwirq_map() function with a linux IRQ number
but it expects a HW irq number. This triggers a BUG on multic-chip
setups in addition to not doing the right thing.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With this change, helpers such as instruction_pointer() et al, get defined
in the generic header in terms of GET_IP
Removed the unnecessary definition of profile_pc in !CONFIG_SMP case as
suggested by Mike Frysinger.
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It appears that on the Chroma card, the class code of the root
complex is still wrong even on DD2 or later chips. This could
be a firmware issue, but that breaks resource allocation so let's
unconditionally fix it up.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When userspace needs to find a specific device, it currently isn't easy to
resolve a /sys/devices/ path from a specific device tree node. Nor is it
easy to obtain the compatible list for devices.
This patch generalizes the code that inserts OF_* values into the uevent
device attribute so that any device that is attached to an OF node will
have that information exported to userspace. Without this patch only
platform devices and some powerpc-specific busses have access to this
data.
The original function also creates a MODALIAS property for the compatible
list, but that code has not been generalized into the common case because
it has the potential to break module loading on a lot of bus types. Bus
types are still responsible for their own MODALIAS properties.
Boot tested on ARM and compile tested on PowerPC and SPARC.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Frederic Lambert <frdrc66@gmail.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Mark Brown <broonie@sirena.org.uk>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On ARM, we don't want SPARSE_IRQ to be a user visible option. Make
SPARSE_IRQ visible based on MAY_HAVE_SPARSE_IRQ instead of depending
on HAVE_SPARSE_IRQ.
With this, SPARSE_IRQ is not visible on C6X and ARM.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-c6x-dev@linux-c6x.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-sh@vger.kernel.org
Commit 9deaa53ac7 broke build
on platforms that use legacy_serial.c without also having
CONFIG_SERIAL_8250_FSL enabled due to an unconditional code
to a routine in that module.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Recent changes to the handling of PCI resources for host bridges
are breaking the PowerNV code for assigning resources on IODA.
The root of the problem is that the pci_bus attached to a host
bridge no longer has its "legacy" resource pointers populated
but only uses the newer list instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I could not find cpus_in_crash anywhere in the sourcetree, except for
arch/powerpc/kernel/crash.c. Moving the definition into the CONFIG_SMP
fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As pointed out, asm/system.h has empty inline implementations for
update_smt_snooze_delay and pseries_notify_cpuidle_add_cpu, which are
used when CONFIG_PSERIES_IDLE is undefined. Since those two functions
are used in core power architecture functions (store_smt_snooze_delay
at kernel/sysfs.c and smp_xics_setup_cpu at platforms/pseries/smp.c),
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enable USB2 controller node for P1020RDB. USB2 controller is used only
when board boots from SPI or SD as it is muxed with eLBC
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
According to latest kernel, the auto-cmd12 property should be
"sdhci,auto-cmd12", and according to the SDHC binding and the workaround for
the special chip, add the chip compatible for eSDHC: "fsl,p1022-esdhc",
"fsl,mpc8536-esdhc", "fsl,p1020-esdhc", "fsl,p2020-esdhc" and
"fsl,p1010-esdhc".
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit: (29 commits)
audit: no leading space in audit_log_d_path prefix
audit: treat s_id as an untrusted string
audit: fix signedness bug in audit_log_execve_info()
audit: comparison on interprocess fields
audit: implement all object interfield comparisons
audit: allow interfield comparison between gid and ogid
audit: complex interfield comparison helper
audit: allow interfield comparison in audit rules
Kernel: Audit Support For The ARM Platform
audit: do not call audit_getname on error
audit: only allow tasks to set their loginuid if it is -1
audit: remove task argument to audit_set_loginuid
audit: allow audit matching on inode gid
audit: allow matching on obj_uid
audit: remove audit_finish_fork as it can't be called
audit: reject entry,always rules
audit: inline audit_free to simplify the look of generic code
audit: drop audit_set_macxattr as it doesn't do anything
audit: inline checks for not needing to collect aux records
audit: drop some potentially inadvisable likely notations
...
Use evil merge to fix up grammar mistakes in Kconfig file.
Bad speling and horrible grammar (and copious swearing) is to be
expected, but let's keep it to commit messages and comments, rather than
expose it to users in config help texts or printouts.
Every arch calls:
if (unlikely(current->audit_context))
audit_syscall_entry()
which requires knowledge about audit (the existance of audit_context) in
the arch code. Just do it all in static inline in audit.h so that arch's
can remain blissfully ignorant.
Signed-off-by: Eric Paris <eparis@redhat.com>
The audit system previously expected arches calling to audit_syscall_exit to
supply as arguments if the syscall was a success and what the return code was.
Audit also provides a helper AUDITSC_RESULT which was supposed to simplify things
by converting from negative retcodes to an audit internal magic value stating
success or failure. This helper was wrong and could indicate that a valid
pointer returned to userspace was a failed syscall. The fix is to fix the
layering foolishness. We now pass audit_syscall_exit a struct pt_reg and it
in turns calls back into arch code to collect the return value and to
determine if the syscall was a success or failure. We also define a generic
is_syscall_success() macro which determines success/failure based on if the
value is < -MAX_ERRNO. This works for arches like x86 which do not use a
separate mechanism to indicate syscall failure.
We make both the is_syscall_success() and regs_return_value() static inlines
instead of macros. The reason is because the audit function must take a void*
for the regs. (uml calls theirs struct uml_pt_regs instead of just struct
pt_regs so audit_syscall_exit can't take a struct pt_regs). Since the audit
function takes a void* we need to use static inlines to cast it back to the
arch correct structure to dereference it.
The other major change is that on some arches, like ia64, MIPS and ppc, we
change regs_return_value() to give us the negative value on syscall failure.
THE only other user of this macro, kretprobe_example.c, won't notice and it
makes the value signed consistently for the audit functions across all archs.
In arch/sh/kernel/ptrace_64.c I see that we were using regs[9] in the old
audit code as the return value. But the ptrace_64.h code defined the macro
regs_return_value() as regs[3]. I have no idea which one is correct, but this
patch now uses the regs_return_value() function, so it now uses regs[3].
For powerpc we previously used regs->result but now use the
regs_return_value() function which uses regs->gprs[3]. regs->gprs[3] is
always positive so the regs_return_value(), much like ia64 makes it negative
before calling the audit code when appropriate.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: H. Peter Anvin <hpa@zytor.com> [for x86 portion]
Acked-by: Tony Luck <tony.luck@intel.com> [for ia64]
Acked-by: Richard Weinberger <richard@nod.at> [for uml]
Acked-by: David S. Miller <davem@davemloft.net> [for sparc]
Acked-by: Ralf Baechle <ralf@linux-mips.org> [for mips]
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> [for ppc]
Add missing iounmap in error handling code, in a case where the function
already preforms iounmap on some other execution path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
statement S,S1;
int ret;
@@
e = \(ioremap\|ioremap_nocache\)(...)
... when != iounmap(e)
if (<+...e...+>) S
... when any
when != iounmap(e)
*if (...)
{ ... when != iounmap(e)
return ...; }
... when any
iounmap(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Current linux-next compiled with mpc85xx_defconfig causes this:
arch/powerpc/platforms/85xx/p1022_ds.c:341:14: error: 'udbg_progress' undeclared here (not in a function)
Add include to fix this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
Kbuild: Use dtc's -d (dependency) option
dtc: Implement -d option to write out a dependency file
kbuild: Fix comment in Makefile.lib
scripts/genksyms: clean lex/yacc generated files
kbuild: Correctly deal with make options which contain an "s"
This hooks dtc into Kbuild's dependency system.
Thus, for example, "make dtbs" will rebuild tegra-harmony.dtb if only
tegra20.dtsi has changed yet tegra-harmony.dts has not. The previous
lack of this feature recently caused me to have very confusing "git
bisect" results.
For ARM, it's obvious what to add to $(targets). I'm not familiar enough
with other architectures to know what to add there. Powerpc appears to
already add various .dtb files into $(targets), but the other archs may
need something added to $(targets) to work.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
[mmarek: Dropped arch/c6x part to avoid merging commits from the middle
of the merge window]
Signed-off-by: Michal Marek <mmarek@suse.cz>
KMSG_DUMP_KEXEC is useless because we already save kernel messages inside
/proc/vmcore, and it is unsafe to allow modules to do other stuffs in a
crash dump scenario.
[akpm@linux-foundation.org: fix powerpc build]
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Reported-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
node_to_cpumask() has been replaced by cpumask_of_node(), and wholly
removed since commit 29c337a0 ("cpumask: remove obsolete node_to_cpumask
now everyone uses cpumask_of_node").
So update the comments for setup_node_to_cpumask_map().
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (80 commits)
x86/PCI: Expand the x86_msi_ops to have a restore MSIs.
PCI: Increase resource array mask bit size in pcim_iomap_regions()
PCI: DEVICE_COUNT_RESOURCE should be equal to PCI_NUM_RESOURCES
PCI: pci_ids: add device ids for STA2X11 device (aka ConneXT)
PNP: work around Dell 1536/1546 BIOS MMCONFIG bug that breaks USB
x86/PCI: amd: factor out MMCONFIG discovery
PCI: Enable ATS at the device state restore
PCI: msi: fix imbalanced refcount of msi irq sysfs objects
PCI: kconfig: English typo in pci/pcie/Kconfig
PCI/PM/Runtime: make PCI traces quieter
PCI: remove pci_create_bus()
xtensa/PCI: convert to pci_scan_root_bus() for correct root bus resources
x86/PCI: convert to pci_create_root_bus() and pci_scan_root_bus()
x86/PCI: use pci_scan_bus() instead of pci_scan_bus_parented()
x86/PCI: read Broadcom CNB20LE host bridge info before PCI scan
sparc32, leon/PCI: convert to pci_scan_root_bus() for correct root bus resources
sparc/PCI: convert to pci_create_root_bus()
sh/PCI: convert to pci_scan_root_bus() for correct root bus resources
powerpc/PCI: convert to pci_create_root_bus()
powerpc/PCI: split PHB part out of pcibios_map_io_space()
...
Fix up conflicts in drivers/pci/msi.c and include/linux/pci_regs.h due
to the same patches being applied in other branches.
Many architectures don't want to pull in iomap.c,
so they ended up duplicating pci_iomap from that file.
That function isn't trivial, and we are going to modify it
https://lkml.org/lkml/2011/11/14/183
so the duplication hurts.
This reduces the scope of the problem significantly,
by moving pci_iomap to a separate file and
referencing that from all architectures.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPBZXBAAoJECgfDbjSjVRpuuYIAIMD0wE96MuTOSBJX4VG8VAP
UyjL9dsfMRy8CKioQo5/fxpTY07YBCWmNauSSX7pzgcoUKBfYIGn4Z1qwGYsWK9M
CzLs6PXLTugw0FtKobHZl/klRTWEBS6YOUjp9x568rplwF+Ppk7b993uj7eS/g+e
T0mUKzqg4/UavbHd9+W5KgC4drQ5hgtu2WZHoUxBK4umnd3C2G+U82Sthg50o/XU
SC8IGm39K8I36HoIWgXj3Y7nkOP3mQELohOT4ZPiVSmLvGS4i47+ix75anO+8ZvZ
jxHr8RC85IK1Nd89NZhbKOyvx0QQiwoKUZaTwcWXJNSOADzZnM6icdIsodc+Elo=
=ccQZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
lib: use generic pci_iomap on all architectures
Many architectures don't want to pull in iomap.c,
so they ended up duplicating pci_iomap from that file.
That function isn't trivial, and we are going to modify it
https://lkml.org/lkml/2011/11/14/183
so the duplication hurts.
This reduces the scope of the problem significantly,
by moving pci_iomap to a separate file and
referencing that from all architectures.
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
alpha: drop pci_iomap/pci_iounmap from pci-noop.c
mn10300: switch to GENERIC_PCI_IOMAP
mn10300: add missing __iomap markers
frv: switch to GENERIC_PCI_IOMAP
tile: switch to GENERIC_PCI_IOMAP
tile: don't panic on iomap
sparc: switch to GENERIC_PCI_IOMAP
sh: switch to GENERIC_PCI_IOMAP
powerpc: switch to GENERIC_PCI_IOMAP
parisc: switch to GENERIC_PCI_IOMAP
mips: switch to GENERIC_PCI_IOMAP
microblaze: switch to GENERIC_PCI_IOMAP
arm: switch to GENERIC_PCI_IOMAP
alpha: switch to GENERIC_PCI_IOMAP
lib: add GENERIC_PCI_IOMAP
lib: move GENERIC_IOMAP to lib/Kconfig
Fix up trivial conflicts due to changes nearby in arch/{m68k,score}/Kconfig
Unpaired calling of __trace_hcall_entry and __trace_hcall_exit could
cause incorrect preempt count. And it might happen as the global
variable hcall_tracepoint_refcount is checked separately before calling
them.
Instead, store the value that was used on entry in the stack frame
and retreive it from there after the call
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tracepoints should not be called inside an rcu_idle_enter/rcu_idle_exit
region. Since pSeries calls H_CEDE in the idle loop, we were violating
this rule.
commit a7b152d534 (powerpc: Tell RCU about idle after hcall tracing)
tried to work around it by delaying the rcu_idle_enter until after we
called the hcall tracepoint, but there are a number of issues with it.
The hcall tracepoint trampoline code is called conditionally when the
tracepoint is enabled. If the tracepoint is not enabled we never call
rcu_idle_enter. The idle_uses_rcu check was also done at compile time
which breaks multiplatform builds.
The simple fix is to avoid tracing H_CEDE and rely on other tracepoints
and the hypervisor dispatch trace log to work out if we called H_CEDE.
This fixes a hang during boot on pSeries.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'kvm-updates/3.3' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (74 commits)
KVM: PPC: Whitespace fix for kvm.h
KVM: Fix whitespace in kvm_para.h
KVM: PPC: annotate kvm_rma_init as __init
KVM: x86 emulator: implement RDPMC (0F 33)
KVM: x86 emulator: fix RDPMC privilege check
KVM: Expose the architectural performance monitoring CPUID leaf
KVM: VMX: Intercept RDPMC
KVM: SVM: Intercept RDPMC
KVM: Add generic RDPMC support
KVM: Expose a version 2 architectural PMU to a guests
KVM: Expose kvm_lapic_local_deliver()
KVM: x86 emulator: Use opcode::execute for Group 9 instruction
KVM: x86 emulator: Use opcode::execute for Group 4/5 instructions
KVM: x86 emulator: Use opcode::execute for Group 1A instruction
KVM: ensure that debugfs entries have been created
KVM: drop bsp_vcpu pointer from kvm struct
KVM: x86: Consolidate PIT legacy test
KVM: x86: Do not rely on implicit inclusions
KVM: Make KVM_INTEL depend on CPU_SUP_INTEL
KVM: Use memdup_user instead of kmalloc/copy_from_user
...
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (65 commits)
tty: serial: imx: move del_timer_sync() to avoid potential deadlock
imx: add polled io uart methods
imx: Add save/restore functions for UART control regs
serial/imx: let probing fail for the dt case without a valid alias
serial/imx: propagate error from of_alias_get_id instead of using -ENODEV
tty: serial: imx: Allow UART to be a source for wakeup
serial: driver for m32 arch should not have DEC alpha errata
serial/documentation: fix documented name of DCD cpp symbol
atmel_serial: fix spinlock lockup in RS485 code
tty: Fix memory leak in virtual console when enable unicode translation
serial: use DIV_ROUND_CLOSEST instead of open coding it
serial: add support for 400 and 800 v3 series Titan cards
serial: bfin-uart: Remove ASYNC_CTS_FLOW flag for hardware automatic CTS.
serial: bfin-uart: Enable hardware automatic CTS only when CTS pin is available.
serial: make FSL errata depend on 8250_CONSOLE, not just 8250
serial: add irq handler for Freescale 16550 errata.
serial: manually inline serial8250_handle_port
serial: make 8250 timeout use the specified IRQ handler
serial: export the key functions for an 8250 IRQ handler
serial: clean up parameter passing for 8250 Rx IRQ handling
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
Kconfig: acpi: Fix typo in comment.
misc latin1 to utf8 conversions
devres: Fix a typo in devm_kfree comment
btrfs: free-space-cache.c: remove extra semicolon.
fat: Spelling s/obsolate/obsolete/g
SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
tools/power turbostat: update fields in manpage
mac80211: drop spelling fix
types.h: fix comment spelling for 'architectures'
typo fixes: aera -> area, exntension -> extension
devices.txt: Fix typo of 'VMware'.
sis900: Fix enum typo 'sis900_rx_bufer_status'
decompress_bunzip2: remove invalid vi modeline
treewide: Fix comment and string typo 'bufer'
hyper-v: Update MAINTAINERS
treewide: Fix typos in various parts of the kernel, and fix some comments.
clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
leds: Kconfig: Fix typo 'D2NET_V2'
sound: Kconfig: drop unknown symbol ARCH_CLPS7500
...
Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
PM / Hibernate: Implement compat_ioctl for /dev/snapshot
PM / Freezer: fix return value of freezable_schedule_timeout_killable()
PM / shmobile: Allow the A4R domain to be turned off at run time
PM / input / touchscreen: Make st1232 use device PM QoS constraints
PM / QoS: Introduce dev_pm_qos_add_ancestor_request()
PM / shmobile: Remove the stay_on flag from SH7372's PM domains
PM / shmobile: Don't include SH7372's INTCS in syscore suspend/resume
PM / shmobile: Add support for the sh7372 A4S power domain / sleep mode
PM: Drop generic_subsys_pm_ops
PM / Sleep: Remove forward-only callbacks from AMBA bus type
PM / Sleep: Remove forward-only callbacks from platform bus type
PM: Run the driver callback directly if the subsystem one is not there
PM / Sleep: Make pm_op() and pm_noirq_op() return callback pointers
PM/Devfreq: Add Exynos4-bus device DVFS driver for Exynos4210/4212/4412.
PM / Sleep: Merge internal functions in generic_ops.c
PM / Sleep: Simplify generic system suspend callbacks
PM / Hibernate: Remove deprecated hibernation snapshot ioctls
PM / Sleep: Fix freezer failures due to racy usermodehelper_is_disabled()
ARM: S3C64XX: Implement basic power domain support
PM / shmobile: Use common always on power domain governor
...
Fix up trivial conflict in fs/xfs/xfs_buf.c due to removal of unused
XBT_FORCE_SLEEP bit
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (165 commits)
reiserfs: Properly display mount options in /proc/mounts
vfs: prevent remount read-only if pending removes
vfs: count unlinked inodes
vfs: protect remounting superblock read-only
vfs: keep list of mounts for each superblock
vfs: switch ->show_options() to struct dentry *
vfs: switch ->show_path() to struct dentry *
vfs: switch ->show_devname() to struct dentry *
vfs: switch ->show_stats to struct dentry *
switch security_path_chmod() to struct path *
vfs: prefer ->dentry->d_sb to ->mnt->mnt_sb
vfs: trim includes a bit
switch mnt_namespace ->root to struct mount
vfs: take /proc/*/mounts and friends to fs/proc_namespace.c
vfs: opencode mntget() mnt_set_mountpoint()
vfs: spread struct mount - remaining argument of next_mnt()
vfs: move fsnotify junk to struct mount
vfs: move mnt_devname
vfs: move mnt_list to struct mount
vfs: switch pnode.h macros to struct mount *
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=9ugo
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Changes queued in gpio/next for the start of the 3.3 merge window
* tag 'gpio-for-linus-20120104' of git://git.secretlab.ca/git/linux-2.6:
gpio: Add decode of WM8994 GPIO configuration
gpio: Convert GPIO drivers to module_platform_driver
gpio: Fix typo in comment in Samsung driver
gpio: Explicitly index samsung_gpio_cfgs
gpio: Add Linus Walleij as gpio co-maintainer
of: Add device tree selftests
of: create of_phandle_args to simplify return of phandle parsing data
gpio/powerpc: Eliminate duplication of of_get_named_gpio_flags()
gpio/microblaze: Eliminate duplication of of_get_named_gpio_flags()
gpiolib: output basic details and consolidate gpio device drivers
pch_gpio: Change company name OKI SEMICONDUCTOR to LAPIS Semiconductor
pch_gpio: Support new device LAPIS Semiconductor ML7831 IOH
spi/pl022: make the chip deselect handling thread safe
spi/pl022: add support for pm_runtime autosuspend
spi/pl022: disable the PL022 block when unused
spi/pl022: move device disable to workqueue thread
spi/pl022: skip default configuration before suspending
spi/pl022: fix build warnings
spi/pl022: only enable RX interrupts when TX is complete
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
arm: fix up some samsung merge sysdev conversion problems
firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
Drivers:hv: Fix a bug in vmbus_driver_unregister()
driver core: remove __must_check from device_create_file
debugfs: add missing #ifdef HAS_IOMEM
arm: time.h: remove device.h #include
driver-core: remove sysdev.h usage.
clockevents: remove sysdev.h
arm: convert sysdev_class to a regular subsystem
arm: leds: convert sysdev_class to a regular subsystem
kobject: remove kset_find_obj_hinted()
m86k: gpio - convert sysdev_class to a regular subsystem
mips: txx9_sram - convert sysdev_class to a regular subsystem
mips: 7segled - convert sysdev_class to a regular subsystem
sh: dma - convert sysdev_class to a regular subsystem
sh: intc - convert sysdev_class to a regular subsystem
power: suspend - convert sysdev_class to a regular subsystem
power: qe_ic - convert sysdev_class to a regular subsystem
power: cmm - convert sysdev_class to a regular subsystem
s390: time - convert sysdev_class to a regular subsystem
...
Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
- arch/arm/mach-exynos/cpu.c
- arch/arm/mach-exynos/irq-eint.c
- arch/arm/mach-s3c64xx/common.c
- arch/arm/mach-s3c64xx/cpu.c
- arch/arm/mach-s5p64x0/cpu.c
- arch/arm/mach-s5pv210/common.c
- arch/arm/plat-samsung/include/plat/cpu.h
- arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (185 commits)
powerpc: fix compile error with 85xx/p1010rdb.c
powerpc: fix compile error with 85xx/p1023_rds.c
powerpc/fsl: add MSI support for the Freescale hypervisor
arch/powerpc/sysdev/fsl_rmu.c: introduce missing kfree
powerpc/fsl: Add support for Integrated Flash Controller
powerpc/fsl: update compatiable on fsl 16550 uart nodes
powerpc/85xx: fix PCI and localbus properties in p1022ds.dts
powerpc/85xx: re-enable ePAPR byte channel driver in corenet32_smp_defconfig
powerpc/fsl: Update defconfigs to enable some standard FSL HW features
powerpc: Add TBI PHY node to first MDIO bus
sbc834x: put full compat string in board match check
powerpc/fsl-pci: Allow 64-bit PCIe devices to DMA to any memory address
powerpc: Fix unpaired probe_hcall_entry and probe_hcall_exit
offb: Fix setting of the pseudo-palette for >8bpp
offb: Add palette hack for qemu "standard vga" framebuffer
offb: Fix bug in calculating requested vram size
powerpc/boot: Change the WARN to INFO for boot wrapper overlap message
powerpc/44x: Fix build error on currituck platform
powerpc/boot: Change the load address for the wrapper to fit the kernel
powerpc/44x: Enable CRASH_DUMP for 440x
...
Fix up a trivial conflict in arch/powerpc/include/asm/cputime.h due to
the additional sparse-checking code for cputime_t.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1958 commits)
net: pack skb_shared_info more efficiently
net_sched: red: split red_parms into parms and vars
net_sched: sfq: extend limits
cnic: Improve error recovery on bnx2x devices
cnic: Re-init dev->stats_addr after chip reset
net_sched: Bug in netem reordering
bna: fix sparse warnings/errors
bna: make ethtool_ops and strings const
xgmac: cleanups
net: make ethtool_ops const
vmxnet3" make ethtool ops const
xen-netback: make ops structs const
virtio_net: Pass gfp flags when allocating rx buffers.
ixgbe: FCoE: Add support for ndo_get_fcoe_hbainfo() call
netdev: FCoE: Add new ndo_get_fcoe_hbainfo() call
igb: reset PHY after recovering from PHY power down
igb: add basic runtime PM support
igb: Add support for byte queue limits.
e1000: cleanup CE4100 MDIO registers access
e1000: unmap ce4100_gbe_mdio_base_virt in e1000_remove
...
Convert from pci_create_bus() to pci_create_root_bus(). This way the root
bus resources are correct immediately. This patch doesn't fix a problem
because powerpc fixed the resources before scanning the bus, but it makes
powerpc more consistent with other architectures.
v2: fix build error with resource pointer passing
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No functional change. This is so we can use pcibios_phb_map_io_space()
before we have a struct pci_bus.
v2: fix map io phb typo
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch converts PowerPC's architecture-specific
'pcibios_set_master()' routine to a non-inlined function. This will
allow follow on patches to create a generic 'pcibios_set_master()'
function using the '__weak' attribute which can be used by all
architectures as a default which, if necessary, can then be over-
ridden by architecture-specific code.
Converting 'pci_bios_set_master()' to a non-inlined function will
allow PowerPC's 'pcibios_set_master()' implementation to remain
architecture-specific after the generic version is introduced and
thus, not change current behavior.
No functional change.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
sched/tracing: Add a new tracepoint for sleeptime
sched: Disable scheduler warnings during oopses
sched: Fix cgroup movement of waking process
sched: Fix cgroup movement of newly created process
sched: Fix cgroup movement of forking process
sched: Remove cfs bandwidth period check in tg_set_cfs_period()
sched: Fix load-balance lock-breaking
sched: Replace all_pinned with a generic flags field
sched: Only queue remote wakeups when crossing cache boundaries
sched: Add missing rcu_dereference() around ->real_parent usage
[S390] fix cputime overflow in uptime_proc_show
[S390] cputime: add sparse checking and cleanup
sched: Mark parent and real_parent as __rcu
sched, nohz: Fix missing RCU read lock
sched, nohz: Set the NOHZ_BALANCE_KICK flag for idle load balancer
sched, nohz: Fix the idle cpu check in nohz_idle_balance
sched: Use jump_labels for sched_feat
sched/accounting: Fix parameter passing in task_group_account_field
sched/accounting: Fix user/system tick double accounting
sched/accounting: Re-use scheduler statistics for the root cgroup
...
Fix up conflicts in
- arch/ia64/include/asm/cputime.h, include/asm-generic/cputime.h
usecs_to_cputime64() vs the sparse cleanups
- kernel/sched/fair.c, kernel/time/tick-sched.c
scheduler changes in multiple branches
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (64 commits)
cpu: Export cpu_up()
rcu: Apply ACCESS_ONCE() to rcu_boost() return value
Revert "rcu: Permit rt_mutex_unlock() with irqs disabled"
docs: Additional LWN links to RCU API
rcu: Augment rcu_batch_end tracing for idle and callback state
rcu: Add rcutorture tests for srcu_read_lock_raw()
rcu: Make rcutorture test for hotpluggability before offlining CPUs
driver-core/cpu: Expose hotpluggability to the rest of the kernel
rcu: Remove redundant rcu_cpu_stall_suppress declaration
rcu: Adaptive dyntick-idle preparation
rcu: Keep invoking callbacks if CPU otherwise idle
rcu: Irq nesting is always 0 on rcu_enter_idle_common
rcu: Don't check irq nesting from rcu idle entry/exit
rcu: Permit dyntick-idle with callbacks pending
rcu: Document same-context read-side constraints
rcu: Identify dyntick-idle CPUs on first force_quiescent_state() pass
rcu: Remove dynticks false positives and RCU failures
rcu: Reduce latency of rcu_prepare_for_idle()
rcu: Eliminate RCU_FAST_NO_HZ grace-period hang
rcu: Avoid needlessly IPIing CPUs at GP end
...
* 'core-memblock-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (52 commits)
memblock: Reimplement memblock allocation using reverse free area iterator
memblock: Kill early_node_map[]
score: Use HAVE_MEMBLOCK_NODE_MAP
s390: Use HAVE_MEMBLOCK_NODE_MAP
mips: Use HAVE_MEMBLOCK_NODE_MAP
ia64: Use HAVE_MEMBLOCK_NODE_MAP
SuperH: Use HAVE_MEMBLOCK_NODE_MAP
sparc: Use HAVE_MEMBLOCK_NODE_MAP
powerpc: Use HAVE_MEMBLOCK_NODE_MAP
memblock: Implement memblock_add_node()
memblock: s/memblock_analyze()/memblock_allow_resize()/ and update users
memblock: Track total size of regions automatically
powerpc: Cleanup memblock usage
memblock: Reimplement memblock_enforce_memory_limit() using __memblock_remove()
memblock: Make memblock functions handle overflowing range @size
memblock: Reimplement __memblock_remove() using memblock_isolate_range()
memblock: Separate out memblock_isolate_range() from memblock_set_node()
memblock: Kill memblock_init()
memblock: Kill sentinel entries at the end of static region arrays
memblock: Add __memblock_dump_all()
...
Current linux-next compiled with mpc85xx_defconfig causes this:
arch/powerpc/platforms/85xx/p1010rdb.c:41:14: error: 'np' undeclared (first use in this function)
arch/powerpc/platforms/85xx/p1023_rds.c:102:14: error: 'np' undeclared (first use in this function)
Introduced in:
commit 996983b75c
Author: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Date: Fri Dec 2 06:28:02 2011 +0000
powerpc/mpic: Search for open-pic device-tree node if NULL
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Current linux-next compiled with mpc85xx_smp_defconfig causes this:
arch/powerpc/platforms/85xx/p1023_rds.c: In function 'mpc85xx_rds_pic_init':
arch/powerpc/platforms/85xx/p1023_rds.c:102:14: error: 'np' undeclared (first use in this function)
arch/powerpc/platforms/85xx/p1023_rds.c:102:14: note: each undeclared identifier is reported only once for each function it appears in
Introduced in:
commit 996983b75c
Author: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Date: Fri Dec 2 06:28:02 2011 +0000
powerpc/mpic: Search for open-pic device-tree node if NULL
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for vmpic-msi nodes to the fsl_msi driver. The MSI is
virtualized by the hypervisor, so the vmpic-msi does not contain a 'reg'
property. Instead, the driver uses hcalls.
Add support for the "msi-address-64" property to the fsl_pci driver.
The Freescale hypervisor typically puts the virtualized MSIIR register
in the page after the end of DDR, so we extend the DDR ATMU to cover it.
Any other location for MSIIR is not supported, for now.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
rmu needs to be freed before leaving the function in an error case.
A simplified version of the semantic match that finds the problem is as
follows: (http://coccinelle.lip6.fr)
// <smpl>
@r exists@
local idexpression x;
statement S;
identifier f1;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
x->f1
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Integrated Flash Controller supports various flashes like NOR, NAND
and other devices using NOR, NAND and GPCM Machine available on it.
IFC supports four chip selects.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Liu Shuo <b35362@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale serial port's are pretty much a 16550, however there are
some FSL specific bugs and features. Add a "fsl,ns16550" compatiable
string to allow code to handle those FSL specific issues.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
PCI ranges, localbus reg and localbus chip-select 2 range do not match
the memory map setup by bootloader.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 7c4b2f09 (powerpc: Update mpc85xx/corenet 32-bit defconfigs)
accidentally disabled the ePAPR byte channel driver in the defconfig for
Freescale CoreNet platforms.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Systems which use the fsl_pq_mdio driver need to specify an
address for TBI PHY transactions such that the address does
not conflict with any PHYs on the bus (all transactions to
that address are directed to the onboard TBI PHY). The driver
used to scan for a free address if no address was specified,
however this ran into issues when the PHY Lib was fixed so
that all MDIO transactions were protected by a mutex. As it
is, the code was meant to serve as a transitional tool until
the device trees were all updated to specify the TBI address.
The best fix for the mutex issue was to remove the scanning code,
but it turns out some of the newer SoCs have started to omit
the tbi-phy node when SGMII is not being used. As such, these
devices will now fail unless we add a tbi-phy node to the first
mdio controller.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The commit 883c2cfc8bcc0fd00c5d9f596fb8870f481b5bda:
"fix of_flat_dt_is_compatible() to match the full compatible string"
causes silent boot death on the sbc8349 board because it was
just looking for 8349 and not 8349E -- as originally there
were non-E (no SEC/encryption) chips available. Just add the
E to the board detection string since all boards I've seen
were manufactured with the E versions.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is an issue on FSL-BookE 64-bit devices (P5020) in which PCIe
devices that are capable of doing 64-bit DMAs (like an Intel e1000) do
not function and crash the kernel if we have >4G of memory in the system.
The reason is that the existing code only sets up one inbound window for
access to system memory across PCIe. That window is limited to a 32-bit
address space. So on systems we'll end up utilizing SWIOTLB for dma
mappings. However SWIOTLB dma ops implement dma_alloc_coherent() as
dma_direct_alloc_coherent(). Thus we can end up with dma addresses that
are not accessible because of the inbound window limitation.
We could possibly set the SWIOTLB alloc_coherent op to
swiotlb_alloc_coherent() however that does not address the issue since
the swiotlb_alloc_coherent() will behave almost identical to
dma_direct_alloc_coherent() since the devices coherent_dma_mask will be
greater than any address allocated by swiotlb_alloc_coherent() and thus
we'll never bounce buffer it into a range that would be dma-able.
The easiest and best solution is to just make it so that a 64-bit
capable device is able to DMA to any internal system address.
We accomplish this by opening up a second inbound window that maps all
of memory above the internal SoC address width so we can set it up to
access all of the internal SoC address space if needed.
We than fixup the dma_ops and dma_offset for PCIe devices with a dma
mask greater than the maximum internal SoC address.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move invalidate_bdev, block_sync_page into fs/block_dev.c. Export
kill_bdev as well, so brd doesn't have to open code it. Reduce
buffer_head.h requirement accordingly.
Removed a rather large comment from invalidate_bdev, as it looked a bit
obsolete to bother moving. The small comment replacing it says enough.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Seeing that just about every destructor got that INIT_LIST_HEAD() copied into
it, there is no point whatsoever keeping this INIT_LIST_HEAD in inode_init_once();
the cost of taking it into inode_init_always() will be negligible for pipes
and sockets and negative for everything else. Not to mention the removal of
boilerplate code from ->destroy_inode() instances...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Unpaired calling of probe_hcall_entry and probe_hcall_exit might happen
as following, which could cause incorrect preempt count.
__trace_hcall_entry => trace_hcall_entry -> probe_hcall_entry =>
get_cpu_var => preempt_disable
__trace_hcall_exit => trace_hcall_exit -> probe_hcall_exit =>
put_cpu_var => preempt_enable
where:
A => B and A -> B means A calls B, but
=> means A will call B through function name, and B will definitely be
called.
-> means A will call B through function pointer, so B might not be
called if the function pointer is not set.
So error happens when only one of probe_hcall_entry and probe_hcall_exit
get called during a hcall.
This patch tries to move the preempt count operations from
probe_hcall_entry and probe_hcall_exit to its callers.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
CC: stable@kernel.org [v2.6.32+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 2a95ea6c0d ("procfs: do not overflow get_{idle,iowait}_time
for nohz") did not take into account that one some architectures jiffies
and cputime use different units.
This causes get_idle_time() to return numbers in the wrong units, making
the idle time fields in /proc/stat wrong.
Instead of converting the usec value returned by
get_cpu_{idle,iowait}_time_us to units of jiffies, use the new function
usecs_to_cputime64 to convert it to the correct unit of cputime64_t.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "Artem S. Tashkinov" <t.artem@mailcity.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kvm_rma_init() is only called at boot-time, by setup_arch, which is also __init.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Introduce id_to_memslot to get memslot by slot id
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This is required for THIS_MODULE. We recently stopped acquiring
it via some other header.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently kvmppc_start_thread() tries to wake other SMT threads via
xics_wake_cpu(). Unfortunately xics_wake_cpu only exists when
CONFIG_SMP=Y so when compiling with CONFIG_SMP=N we get:
arch/powerpc/kvm/built-in.o: In function `.kvmppc_start_thread':
book3s_hv.c:(.text+0xa1e0): undefined reference to `.xics_wake_cpu'
The following should be fine since kvmppc_start_thread() shouldn't
called to start non-zero threads when SMP=N since threads_per_core=1.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
kvmppc_h_pr is only available if CONFIG_KVM_BOOK3S_64_PR.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
compute_tlbie_rb is only used on ppc64 and cannot be compiled on ppc32.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The sysdev.h file should not be needed by any in-kernel code, so remove
the .h file from these random files that seem to still want to include
it.
The sysdev code will be going away soon, so this include needs to be
removed no matter what.
Cc: Jiandong Zheng <jdzheng@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "Venkatesh Pallipadi
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
After all sysdev classes are ported to regular driver core entities, the
sysdev implementation will be entirely removed from the kernel.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After all sysdev classes are ported to regular driver core entities, the
sysdev implementation will be entirely removed from the kernel.
Cc: Timur Tabi <timur@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After all sysdev classes are ported to regular driver core entities, the
sysdev implementation will be entirely removed from the kernel.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This moves the 'memory sysdev_class' over to a regular 'memory' subsystem
and converts the devices to regular devices. The sysdev drivers are
implemented as subsystem interfaces now.
After all sysdev classes are ported to regular driver core entities, the
sysdev implementation will be entirely removed from the kernel.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This moves the 'cpu sysdev_class' over to a regular 'cpu' subsystem
and converts the devices to regular devices. The sysdev drivers are
implemented as subsystem interfaces now.
After all sysdev classes are ported to regular driver core entities, the
sysdev implementation will be entirely removed from the kernel.
Userspace relies on events and generic sysfs subsystem infrastructure
from sysdev devices, which are made available with this conversion.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Borislav Petkov <bp@amd64.org>
Cc: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Cc: Len Brown <lenb@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since the PM core is now going to execute driver callbacks directly
if the corresponding subsystem callbacks are not present,
forward-only subsystem callbacks (i.e. such that only execute the
corresponding driver callbacks) are not necessary any more. Thus
it is possible to remove generic_subsys_pm_ops, because the only
callback in there that is not forward-only, .runtime_idle, is not
really used by the only user of generic_subsys_pm_ops, which is
vio_bus_type.
However, the generic callback routines themselves cannot be removed
from generic_ops.c, because they are used individually by a number
of subsystems.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* master: (848 commits)
SELinux: Fix RCU deref check warning in sel_netport_insert()
binary_sysctl(): fix memory leak
mm/vmalloc.c: remove static declaration of va from __get_vm_area_node
ipmi_watchdog: restore settings when BMC reset
oom: fix integer overflow of points in oom_badness
memcg: keep root group unchanged if creation fails
nilfs2: potential integer overflow in nilfs_ioctl_clean_segments()
nilfs2: unbreak compat ioctl
cpusets: stall when updating mems_allowed for mempolicy or disjoint nodemask
evm: prevent racing during tfm allocation
evm: key must be set once during initialization
mmc: vub300: fix type of firmware_rom_wait_states module parameter
Revert "mmc: enable runtime PM by default"
mmc: sdhci: remove "state" argument from sdhci_suspend_host
x86, dumpstack: Fix code bytes breakage due to missing KERN_CONT
IB/qib: Correct sense on freectxts increment and decrement
RDMA/cma: Verify private data length
cgroups: fix a css_set not found bug in cgroup_attach_proc
oprofile: Fix uninitialized memory access when writing to writing to oprofilefs
Revert "xen/pv-on-hvm kexec: add xs_reset_watches to shutdown watches from old kernel"
...
Conflicts:
kernel/cgroup_freezer.c
commit c55aef0e5b ("powerpc/boot: Change the load address
for the wrapper to fit the kernel") introduced a WARNING to
inform the user that the uncompressed kernel would overlap
the boot uncompressing wrapper code. Change it to an INFO.
I initially thought, this would be a 'WARNING' for the those
boards, where the link_address should be fixed, so that the
user can take actions accordingly.
Changing the same to INFO.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Put the logic to compute the event index into a per pmu method. This
is required because the x86 rules are weird and wonderful and don't
match the capabilities of the current scheme.
AFAIK only powerpc actually has a usable userspace read of the PMCs
but I'm not at all sure anybody actually used that.
ARM is restored to the default since it currently does not support
userspace access at all. And all software events are provided with a
method that reports their index as 0 (disabled).
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Michael Cree <mcree@orcon.net.nz>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Arun Sharma <asharma@fb.com>
Link: http://lkml.kernel.org/n/tip-dfydxodki16lylkt3gl2j7cw@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The MPIC_PRIMARY define was recently made "default" and the meaning was
inverted to MPIC_SECONDARY. This causes compile errors in currituck now, so
fix it to the new manner of allocating mpics.
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
The wrapper code which uncompresses the kernel in case of a 'ppc' boot
is by default loaded at 0x00400000 and the kernel will be uncompressed
to fit the location 0-0x00400000. But with dynamic relocations, the size
of the kernel may exceed 0x00400000(4M). This would cause an overlap
of the uncompressed kernel and the boot wrapper, causing a failure in
boot.
The message looks like :
zImage starting: loaded at 0x00400000 (sp: 0x0065ffb0)
Allocating 0x5ce650 bytes for kernel ...
Insufficient memory for kernel at address 0! (_start=00400000, uncompressed size=00591a20)
This patch shifts the load address of the boot wrapper code to the next
higher MB, according to the size of the uncompressed vmlinux.
With the patch, we get the following message while building the image :
WARN: Uncompressed kernel (size 0x5b0344) overlaps the address of the wrapper(0x400000)
WARN: Fixing the link_address of wrapper to (0x600000)
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Now that we have relocatable kernel, supporting CRASH_DUMP only requires
turning the switches on for UP machines.
We don't have kexec support on 47x yet. Enabling SMP support would be done
as part of enabling the PPC_47x support.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
The following patch adds relocatable kernel support - based on processing
of dynamic relocations - for PPC44x kernel.
We find the runtime address of _stext and relocate ourselves based
on the following calculation.
virtual_base = ALIGN(KERNELBASE,256M) +
MODULO(_stext.run,256M)
relocate() is called with the Effective Virtual Base Address (as
shown below)
| Phys. Addr| Virt. Addr |
Page (256M) |------------------------|
Boundary | | |
| | |
| | |
Kernel Load |___________|_ __ _ _ _ _|<- Effective
Addr(_stext)| | ^ |Virt. Base Addr
| | | |
| | | |
| |reloc_offset|
| | | |
| | | |
| |______v_____|<-(KERNELBASE)%256M
| | |
| | |
| | |
Page(256M) |-----------|------------|
Boundary | | |
The virt_phys_offset is updated accordingly, i.e,
virt_phys_offset = effective. kernel virt base - kernstart_addr
I have tested the patches on 440x platforms only. However this should
work fine for PPC_47x also, as we only depend on the runtime address
and the current TLB XLAT entry for the startup code, which is available
in r25. I don't have access to a 47x board yet. So, it would be great if
somebody could test this on 47x.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Tony Breeds <tony@bakeyournoodle.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
We find the runtime address of _stext and relocate ourselves based
on the following calculation.
virtual_base = ALIGN(KERNELBASE,KERNEL_TLB_PIN_SIZE) +
MODULO(_stext.run,KERNEL_TLB_PIN_SIZE)
relocate() is called with the Effective Virtual Base Address (as
shown below)
| Phys. Addr| Virt. Addr |
Page |------------------------|
Boundary | | |
| | |
| | |
Kernel Load |___________|_ __ _ _ _ _|<- Effective
Addr(_stext)| | ^ |Virt. Base Addr
| | | |
| | | |
| |reloc_offset|
| | | |
| | | |
| |______v_____|<-(KERNELBASE)%TLB_SIZE
| | |
| | |
| | |
Page |-----------|------------|
Boundary | | |
On BookE, we need __va() & __pa() early in the boot process to access
the device tree.
Currently this has been defined as :
#define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) -
PHYSICAL_START + KERNELBASE)
where:
PHYSICAL_START is kernstart_addr - a variable updated at runtime.
KERNELBASE is the compile time Virtual base address of kernel.
This won't work for us, as kernstart_addr is dynamic and will yield different
results for __va()/__pa() for same mapping.
e.g.,
Let the kernel be loaded at 64MB and KERNELBASE be 0xc0000000 (same as
PAGE_OFFSET).
In this case, we would be mapping 0 to 0xc0000000, and kernstart_addr = 64M
Now __va(1MB) = (0x100000) - (0x4000000) + 0xc0000000
= 0xbc100000 , which is wrong.
it should be : 0xc0000000 + 0x100000 = 0xc0100000
On platforms which support AMP, like PPC_47x (based on 44x), the kernel
could be loaded at highmem. Hence we cannot always depend on the compile
time constants for mapping.
Here are the possible solutions:
1) Update kernstart_addr(PHSYICAL_START) to match the Physical address of
compile time KERNELBASE value, instead of the actual Physical_Address(_stext).
The disadvantage is that we may break other users of PHYSICAL_START. They
could be replaced with __pa(_stext).
2) Redefine __va() & __pa() with relocation offset
#ifdef CONFIG_RELOCATABLE_PPC32
#define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) - PHYSICAL_START + (KERNELBASE + RELOC_OFFSET)))
#define __pa(x) ((unsigned long)(x) + PHYSICAL_START - (KERNELBASE + RELOC_OFFSET))
#endif
where, RELOC_OFFSET could be
a) A variable, say relocation_offset (like kernstart_addr), updated
at boot time. This impacts performance, as we have to load an additional
variable from memory.
OR
b) #define RELOC_OFFSET ((PHYSICAL_START & PPC_PIN_SIZE_OFFSET_MASK) - \
(KERNELBASE & PPC_PIN_SIZE_OFFSET_MASK))
This introduces more calculations for doing the translation.
3) Redefine __va() & __pa() with a new variable
i.e,
#define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) + VIRT_PHYS_OFFSET))
where VIRT_PHYS_OFFSET :
#ifdef CONFIG_RELOCATABLE_PPC32
#define VIRT_PHYS_OFFSET virt_phys_offset
#else
#define VIRT_PHYS_OFFSET (KERNELBASE - PHYSICAL_START)
#endif /* CONFIG_RELOCATABLE_PPC32 */
where virt_phy_offset is updated at runtime to :
Effective KERNELBASE - kernstart_addr.
Taking our example, above:
virt_phys_offset = effective_kernelstart_vaddr - kernstart_addr
= 0xc0400000 - 0x400000
= 0xc0000000
and
__va(0x100000) = 0xc0000000 + 0x100000 = 0xc0100000
which is what we want.
I have implemented (3) in the following patch which has same cost of
operation as the existing one.
I have tested the patches on 440x platforms only. However this should
work fine for PPC_47x also, as we only depend on the runtime address
and the current TLB XLAT entry for the startup code, which is available
in r25. I don't have access to a 47x board yet. So, it would be great if
somebody could test this on 47x.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
The following patch implements the dynamic relocation processing for
PPC32 kernel. relocate() accepts the target virtual address and relocates
the kernel image to the same.
Currently the following relocation types are handled :
R_PPC_RELATIVE
R_PPC_ADDR16_LO
R_PPC_ADDR16_HI
R_PPC_ADDR16_HA
The last 3 relocations in the above list depends on value of Symbol indexed
whose index is encoded in the Relocation entry. Hence we need the Symbol
Table for processing such relocations.
Note: The GNU ld for ppc32 produces buggy relocations for relocation types
that depend on symbols. The value of the symbols with STB_LOCAL scope
should be assumed to be zero. - Alan Modra
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alan Modra <amodra@au1.ibm.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
DYNAMIC_MEMSTART(old RELOCATABLE) was restricted only to PPC_47x variants
of 44x. This patch enables DYNAMIC_MEMSTART for 440x based chipsets.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux ppc dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
The current implementation of CONFIG_RELOCATABLE in BookE is based
on mapping the page aligned kernel load address to KERNELBASE. This
approach however is not enough for platforms, where the TLB page size
is large (e.g, 256M on 44x). So we are renaming the RELOCATABLE used
currently in BookE to DYNAMIC_MEMSTART to reflect the actual method.
The CONFIG_RELOCATABLE for PPC32(BookE) based on processing of the
dynamic relocations will be introduced in the later in the patch series.
This change would allow the use of the old method of RELOCATABLE for
platforms which can afford to enforce the page alignment (platforms with
smaller TLB size).
Changes since v3:
* Introduced a new config, NONSTATIC_KERNEL, to denote a kernel which is
either a RELOCATABLE or DYNAMIC_MEMSTART(Suggested by: Josh Boyer)
Suggested-by: Scott Wood <scottwood@freescale.com>
Tested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux ppc dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
As the kernels and initrd's get bigger boot-loaders and possibly
kexec-tools will need to place the initrd outside the RMO. When this
happens we end up with no lowmem and the boot doesn't get very far.
Only use initrd_end as the limit for alloc_bottom if it's inside the
RMO.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We support 16TB of user address space and half a million contexts
so update the comment to reflect this.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit d57af9b (taskstats: use real microsecond granularity for CPU times)
renamed msecs_to_cputime to usecs_to_cputime, but failed to update all
numbers on the way. This causes nonsensical cpu idle/iowait values to be
displayed in /proc/stat (the only user of usecs_to_cputime so far).
This also renames __cputime_msec_factor to __cputime_usec_factor, adapting
its value and using it directly in cputime_to_usecs instead of doing two
multiplications.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
read_n_cells() cannot be marked as .devinit.text since it is referenced
from two functions that are not in that section: of_get_lmb_size() and
hot_add_drconf_scn_to_nid().
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
mark_reserved_regions_for_nid() is only called from do_init_bootmem(),
which is in .init.text, so it must be in the same section to avoid a
section mismatch warning.
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PPC64 uses long long for u64 in the kernel, but powerpc's asm/types.h
prevents 64-bit userland from seeing this definition, instead defaulting
to u64 == long in userspace. Some user programs (e.g. kvmtool) may actually
want LL64, so this patch adds a check for __SANE_USERSPACE_TYPES__ so that,
if defined, int-ll64.h is included instead.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Implement a POWER7 optimised copy_to_user/copy_from_user using VMX.
For large aligned copies this new loop is over 10% faster, and for
large unaligned copies it is over 200% faster.
If we take a fault we fall back to the old version, this keeps
things relatively simple and easy to verify.
On POWER7 unaligned stores rarely slow down - they only flush when
a store crosses a 4KB page boundary. Furthermore this flush is
handled completely in hardware and should be 20-30 cycles.
Unaligned loads on the other hand flush much more often - whenever
crossing a 128 byte cache line, or a 32 byte sector if either sector
is an L1 miss.
Considering this information we really want to get the loads aligned
and not worry about the alignment of the stores. Microbenchmarks
confirm that this approach is much faster than the current unaligned
copy loop that uses shifts and rotates to ensure both loads and
stores are aligned.
We also want to try and do the stores in cacheline aligned, cacheline
sized chunks. If the store queue is unable to merge an entire
cacheline of stores then the L2 cache will have to do a
read/modify/write. Even worse, we will serialise this with the stores
in the next iteration of the copy loop since both iterations hit
the same cacheline.
Based on this, the new loop does the following things:
1 - 127 bytes
Get the source 8 byte aligned and use 8 byte loads and stores. Pretty
boring and similar to how the current loop works.
128 - 4095 bytes
Get the source 8 byte aligned and use 8 byte loads and stores,
1 cacheline at a time. We aren't doing the stores in cacheline
aligned chunks so we will potentially serialise once per cacheline.
Even so it is much better than the loop we have today.
4096 - bytes
If both source and destination have the same alignment get them both
16 byte aligned, then get the destination cacheline aligned. Do
cacheline sized loads and stores using VMX.
If source and destination do not have the same alignment, we get the
destination cacheline aligned, and use permute to do aligned loads.
In both cases the VMX loop should be optimal - we always do aligned
loads and stores and are always doing stores in cacheline aligned,
cacheline sized chunks.
To be able to use VMX we must be careful about interrupts and
sleeping. We don't use the VMX loop when in an interrupt (which should
be rare anyway) and we wrap the VMX loop in disable/enable_pagefault
and fall back to the existing copy_tofrom_user loop if we do need to
sleep.
The VMX breakpoint of 4096 bytes was chosen using this microbenchmark:
http://ozlabs.org/~anton/junkcode/copy_to_user.c
Since we are using VMX and there is a cost to saving and restoring
the user VMX state there are two broad cases we need to benchmark:
- Best case - userspace never uses VMX
- Worst case - userspace always uses VMX
In reality a userspace process will sit somewhere between these two
extremes. Since we need to test both aligned and unaligned copies we
end up with 4 combinations. The point at which the VMX loop begins to
win is:
0% VMX
aligned 2048 bytes
unaligned 2048 bytes
100% VMX
aligned 16384 bytes
unaligned 8192 bytes
Considering this is a microbenchmark, the data is hot in cache and
the VMX loop has better store queue merging properties we set the
breakpoint to 4096 bytes, a little below the unaligned breakpoints.
Some future optimisations we can look at:
- Looking at the perf data, a significant part of the cost when a
task is always using VMX is the extra exception we take to restore
the VMX state. As such we should do something similar to the x86
optimisation that restores FPU state for heavy users. ie:
/*
* If the task has used fpu the last 5 timeslices, just do a full
* restore of the math state immediately to avoid the trap; the
* chances of needing FPU soon are obviously high now
*/
preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5;
and
/*
* fpu_counter contains the number of consecutive context switches
* that the FPU is used. If this is over a threshold, the lazy fpu
* saving becomes unlazy to save the trap. This is an unsigned char
* so that after 256 times the counter wraps and the behavior turns
* lazy again; this to deal with bursty apps that only use FPU for
* a short time
*/
- We could create a paca bit to mirror the VMX enabled MSR bit and check
that first, avoiding multiple calls to calling enable_kernel_altivec.
That should help with iovec based system calls like readv.
- We could have two VMX breakpoints, one for when we know the user VMX
state is loaded into the registers and one when it isn't. This could
be a second bit in the paca so we can calculate the break points quickly.
- One suggestion from Ben was to save and restore the VSX registers
we use inline instead of using enable_kernel_altivec.
[BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC]
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As of commit dd472da38, rwsem.h was moved into asm-generic.
This patch removes the arch file and points the build at
its new location.
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The code for "powersurge" SMP would kick in and cause a crash
at boot due to the lack of a NULL test.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In the old days, we treated all interrupts from the legacy Apple home made
interrupt controllers as level, with a trick reading the "level" register
along with the "event" register to work arounds bugs where it would
occasionally fail to latch some events.
Doing so appeared to work fine for both level and edge interrupts.
Later on, we discovered in Darwin source the magic masks that define which
interrupts are actually level and which are edge, and implemented a
different algorithm, more similar to what Apple does, that treats those
differently.
I recently discovered however that this caused problems (including loss
of interrupts) with an old Wallstreet PowerBook when trying to use the
internal modem (connected to a cascaded controller).
It looks like some interrupts are treated as edge while they are really
level and I'm starting to seriously doubt the correctness of the Darwin
code (which has other obvious bugs when you read it, so ...)
This patch reverts to our original behaviour of treating everything as
a level interrupt. It appears to solve the problems with the modem on
the Wallstreet and everything else seems to be working properly as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make cputime_t and cputime64_t nocast to enable sparse checking to
detect incorrect use of cputime. Drop the cputime macros for simple
scalar operations. The conversion macros are still needed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A large chunk of qe_pin_request() is unnecessarily cut-and-paste
directly from of_get_named_gpio_flags(). This patch cuts out the
duplicate code and replaces it with a call to of_get_gpio().
v2: fixed compile error due to missing gpio_to_chip()
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Those two APIs were provided to optimize the calls of
tick_nohz_idle_enter() and rcu_idle_enter() into a single
irq disabled section. This way no interrupt happening in-between would
needlessly process any RCU job.
Now we are talking about an optimization for which benefits
have yet to be measured. Let's start simple and completely decouple
idle rcu and dyntick idle logics to simplify.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The PowerPC pSeries platform (CONFIG_PPC_PSERIES=y) enables
hypervisor-call tracing for CONFIG_TRACEPOINTS=y kernels. One of the
hypervisor calls that is traced is the H_CEDE call in the idle loop
that tells the hypervisor that this OS instance no longer needs the
current CPU. However, tracing uses RCU, so this combination of kernel
configuration variables needs to avoid telling RCU about the current CPU's
idleness until after the H_CEDE-entry tracing completes on the one hand,
and must tell RCU that the the current CPU is no longer idle before the
H_CEDE-exit tracing starts.
In all other cases, it suffices to inform RCU of CPU idleness upon
idle-loop entry and exit.
This commit makes the required adjustments.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
It is assumed that rcu won't be used once we switch to tickless
mode and until we restart the tick. However this is not always
true, as in x86-64 where we dereference the idle notifiers after
the tick is stopped.
To prepare for fixing this, add two new APIs:
tick_nohz_idle_enter_norcu() and tick_nohz_idle_exit_norcu().
If no use of RCU is made in the idle loop between
tick_nohz_enter_idle() and tick_nohz_exit_idle() calls, the arch
must instead call the new *_norcu() version such that the arch doesn't
need to call rcu_idle_enter() and rcu_idle_exit().
Otherwise the arch must call tick_nohz_enter_idle() and
tick_nohz_exit_idle() and also call explicitly:
- rcu_idle_enter() after its last use of RCU before the CPU is put
to sleep.
- rcu_idle_exit() before the first use of RCU after the CPU is woken
up.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The tick_nohz_stop_sched_tick() function, which tries to delay
the next timer tick as long as possible, can be called from two
places:
- From the idle loop to start the dytick idle mode
- From interrupt exit if we have interrupted the dyntick
idle mode, so that we reprogram the next tick event in
case the irq changed some internal state that requires this
action.
There are only few minor differences between both that
are handled by that function, driven by the ts->inidle
cpu variable and the inidle parameter. The whole guarantees
that we only update the dyntick mode on irq exit if we actually
interrupted the dyntick idle mode, and that we enter in RCU extended
quiescent state from idle loop entry only.
Split this function into:
- tick_nohz_idle_enter(), which sets ts->inidle to 1, enters
dynticks idle mode unconditionally if it can, and enters into RCU
extended quiescent state.
- tick_nohz_irq_exit() which only updates the dynticks idle mode
when ts->inidle is set (ie: if tick_nohz_idle_enter() has been called).
To maintain symmetry, tick_nohz_restart_sched_tick() has been renamed
into tick_nohz_idle_exit().
This simplifies the code and micro-optimize the irq exit path (no need
for local_irq_save there). This also prepares for the split between
dynticks and rcu extended quiescent state logics. We'll need this split to
further fix illegal uses of RCU in extended quiescent states in the idle
loop.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Sending a break on the SOC UARTs found in some MPC83xx/85xx/86xx
chips seems to cause a short lived IRQ storm (/proc/interrupts
typically shows somewhere between 300 and 1500 events). Unfortunately
this renders SysRQ over the serial console completely inoperable.
The suggested workaround in the errata is to read the Rx register,
wait one character period, and then read the Rx register again.
We achieve this by tracking the old LSR value, and on the subsequent
interrupt event after a break, we don't read LSR, instead we just
read the RBR again and return immediately.
The "fsl,ns16550" is used in the compatible field of the serial
device to mark UARTs known to have this issue.
Thanks to Scott Wood for providing the errata data which led to
a much cleaner fix.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The upcomming currituck patches will need to do 64-bit shifts which will
fail with undefined symbol without this patch.
I looked at linking against libgcc but we can't guarantee that libgcc
was compiled with soft-float. Also Using ../lib/div64.S or
../kernel/misc_32.S, this will break the build as the .o's need to be
built with different flags for the bootwrapper vs the kernel. So for
now the easyest option is to just copy code from
arch/powerpc/kernel/misc_32.S I don't think this code changes too often ;P
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
CONFIG_PPC47x doesn't exist in Kconfig and no 476 processor calls this
function ppc44x_pin_tlb() as it has it's own ppc47x_pin_tlb().
This code is probably an artifact of the original 476 code that
shouldn't have made it upstream.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Needed if you want to use swiotlb, harmless otherwise.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Currituck doesn't need nor use SDR so aborting the pci setup if there is
no sdr-base would be bad.
Add a flag to ppc4xx_pciex_hwops for the backends to state if they need
SDR and then only complain and abort if they do and it's not found in
the device tree.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Now all ARCH_POPULATES_NODE_MAP archs select HAVE_MEBLOCK_NODE_MAP -
there's no user of early_node_map[] left. Kill early_node_map[] and
replace ARCH_POPULATES_NODE_MAP with HAVE_MEMBLOCK_NODE_MAP. Also,
relocate for_each_mem_pfn_range() and helper from mm.h to memblock.h
as page_alloc.c would no longer host an alternative implementation.
This change is ultimately one to one mapping and shouldn't cause any
observable difference; however, after the recent changes, there are
some functions which now would fit memblock.c better than page_alloc.c
and dependency on HAVE_MEMBLOCK_NODE_MAP instead of HAVE_MEMBLOCK
doesn't make much sense on some of them. Further cleanups for
functions inside HAVE_MEMBLOCK_NODE_MAP in mm.h would be nice.
-v2: Fix compile bug introduced by mis-spelling
CONFIG_HAVE_MEMBLOCK_NODE_MAP to CONFIG_MEMBLOCK_HAVE_NODE_MAP in
mmzone.h. Reported by Stephen Rothwell.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
powerpc doesn't access early_node_map[] directly and enabling
HAVE_MEMBLOCK_NODE_MAP is trivial - replacing add_active_range() calls
with memblock_set_node() and selecting HAVE_MEMBLOCK_NODE_MAP is
enough.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
The only function of memblock_analyze() is now allowing resize of
memblock region arrays. Rename it to memblock_allow_resize() and
update its users.
* The following users remain the same other than renaming.
arm/mm/init.c::arm_memblock_init()
microblaze/kernel/prom.c::early_init_devtree()
powerpc/kernel/prom.c::early_init_devtree()
openrisc/kernel/prom.c::early_init_devtree()
sh/mm/init.c::paging_init()
sparc/mm/init_64.c::paging_init()
unicore32/mm/init.c::uc32_memblock_init()
* In the following users, analyze was used to update total size which
is no longer necessary.
powerpc/kernel/machine_kexec.c::reserve_crashkernel()
powerpc/kernel/prom.c::early_init_devtree()
powerpc/mm/init_32.c::MMU_init()
powerpc/mm/tlb_nohash.c::__early_init_mmu()
powerpc/platforms/ps3/mm.c::ps3_mm_add_memory()
powerpc/platforms/embedded6xx/wii.c::wii_memory_fixups()
sh/kernel/machine_kexec.c::reserve_crashkernel()
* x86/kernel/e820.c::memblock_x86_fill() was directly setting
memblock_can_resize before populating memblock and calling analyze
afterwards. Call memblock_allow_resize() before start populating.
memblock_can_resize is now static inside memblock.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "H. Peter Anvin" <hpa@zytor.com>
* early_init_devtree(): Total memory size is aligned to PAGE_SIZE;
however, alignment isn't enforced if memory_limit is explicitly
specified. Simplify the logic and always apply PAGE_SIZE alignment.
* MMU_init(): memblock regions is truncated by directly modifying
memblock.memory.cnt. This is incomplete (reserved array is not
truncated) and unnecessarily low level hindering further memblock
improvments. Use memblock_enforce_memory_limit() instead.
* wii_memory_fixups(): Unnecessarily low level direct manipulation of
memblock regions. The same result can be achieved using properly
abstracted operations. Reimplement using memblock API.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
memblock_init() initializes arrays for regions and memblock itself;
however, all these can be done with struct initializers and
memblock_init() can be removed. This patch kills memblock_init() and
initializes memblock with struct initializer.
The only difference is that the first dummy entries don't have .nid
set to MAX_NUMNODES initially. This doesn't cause any behavior
difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "H. Peter Anvin" <hpa@zytor.com>
24aa07882b (memblock, x86: Replace memblock_x86_reserve/free_range()
with generic ones) removed arch/x86/include/asm/memblock.h and dropped
its inclusion from include/linux/memblock.h which breaks other
architectures which depended on the generic memblock.h pulling in the
arch specific one.
However, the proper fix isn't adding back the asm inclusion. memblock
doesn't have any arch dependent part and doesn't need arch specific
header file and asm/memblock.h files are either practically empty or
contain mostly unrelated arch specific stuff.
* In microblaze, sh, powerpc, sparc and openrisc, asm/memblock.h is
either empty or just contains unused MEMBLOCK_DBG() macro. Remove
them.
* In arm and unicore32, asm/memblock.h contains arch specific stuff.
Include it directly from its users. It might be a good idea to
rename the header file to avoid confusion.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Most distros use it so we may as well enable it and get regular compile
testing.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When issuing a system reset we almost always oops in the oops_to_nvram
code because multiple CPUs are using the deflate work area. Add a
spinlock to protect it.
To play it safe I'm using trylock to avoid locking up if the NVRAM
code oopses. This means we might miss multiple CPUs oopsing at exactly
the same time but I think it's best to play it safe for now. Once we
are happy with the reliability we can change it to a full spinlock.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This fixes a problem where a CPU thread coming out of nap mode can
think it has valid values in the nonvolatile GPRs (r14 - r31) as saved
away in power7_idle, but in fact the values have been trashed because
the thread was used for KVM in the mean time. The result is that the
thread crashes because code that called power7_idle (e.g.,
pnv_smp_cpu_kill_self()) goes to use values in registers that have
been trashed.
The bit field in SRR1 that tells whether state was lost only reflects
the most recent nap, which may not have been the nap instruction in
power7_idle. So we need an extra PACA field to indicate that state
has been lost even if SRR1 indicates that the most recent nap didn't
lose state. We clear this field when saving the state in power7_idle,
we set it to a non-zero value when we use the thread for KVM, and we
test it in power7_wakeup_noloss.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At present, on the powernv platform, if you off-line a CPU that was
online, and then try to on-line it again, the kernel generates a
warning message "OPAL Error -1 starting CPU n". Furthermore, if the
CPU is a secondary thread that was used by KVM while it was off-line,
the CPU fails to come online.
The first problem is fixed by only calling OPAL to start the CPU the
first time it is on-lined, as indicated by the cpu_start field of its
PACA being zero. The second problem is fixed by restoring the
cpu_start field to 1 instead of 0 when using the CPU within KVM.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The minimum RMO size field in ibm,client-architecture is currently
ignored, but a future firmware version will rectify that. Since we
always get at least 128MB of RMO right now, asking for 64MB is
likely to result in boot failures.
We should bump it to at least 128MB, but considering all the boot
issues we have on 128MB RMO boxes and all new machines have virtual
RMO, we may as well set our minimum to 256MB.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With CONFIG_STRICT_DEVMEM=y, user space cannot read any part of /dev/mem.
Since this breaks librtas, punch a hole in /dev/mem to allow access to the
rmo_buffer that librtas needs.
Anton Blanchard reported the problem and helped with the fix.
A quick test for this patch:
# cat /proc/rtas/rmo_buffer
000000000f190000 10000
# python -c "print 0x000000000f190000 / 0x10000"
3865
# dd if=/dev/mem of=/tmp/foo count=1 bs=64k skip=3865
1+0 records in
1+0 records out
65536 bytes (66 kB) copied, 0.000205235 s, 319 MB/s
# dd if=/dev/mem of=/tmp/foo
dd: reading `/dev/mem': Operation not permitted
0+0 records in
0+0 records out
0 bytes (0 B) copied, 0.00022519 s, 0.0 kB/s
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
So I've had one of these for a while and it looks like the vendor never
bothered submitting the support upstream.
This adds it using ppc40x_simple and provides a device-tree.
There are some changes to the boot wrapper because the way u-boot works
on this thing, it seems to expect a multipart image with the kernel,
initrd and dtb in it.
The USB support is missing as it needs the yet unmerged driver for
the DWC OTG part and the GPIOs may need further definition in the dts.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Refresh ps3_defconfig to latest kernel sources and
change the options:
CONFIG_PPP=m to CONFIG_PPP=n.
CONFIG_NAMESPACES=y to CONFIG_NAMESPACES=n
CONFIG_NUMA=y to CONFIG_NUMA=n
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add an __init annotation to the ps3_smp_probe() routine.
Fixes build warnings like these when
CONFIG_DEBUG_SECTION_MISMATCH=y:
WARNING: Section mismatch in reference from the function .ps3_smp_probe()
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix some PS3 repository.c build warnings when DEBUG is
defined. Also change most pr_debug calls to pr_devel calls.
Fixes warnings like these:
format '%lx' expects type 'long unsigned int', but argument 7 has type 'u64'
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The lv1 hcall #91 should be named lv1_read_repository_node, and
not lv1_get_repository_node_value. Adjust the lv1 hcall table
and all calls.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The lv1_get_version_info hcall takes 2, not 1 output
arguments. Adjust the lv1 hcall table and all calls.
Usage:
int lv1_get_version_info(u64 *version_number, u64 *vendor_id)
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The lv1_get_virtual_address_space_id_of_ppe hcall takes 0, not 1 input
arguments. Adjust the lv1 hcall table and all calls.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The lv1_net_stop_tx_dma and net_stop_rx_dma hcalls take 2, not 3 input
arguments. Adjust the lv1 hcall table and all calls.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
General code cleanup for PS3 interrupt.c:
o Fill out comments for structure members.
o Move variables ipi_debug_brk_mask and lock from struct ps3_bmp to
struct ps3_private.
o Fix pr_debug build errors when DEBUG is defined.
o Convert bit operation to set_bit().
o Convert DBG macro from pr_debug to pr_devel
o Add new macro FAIL to replace pr_debug calls
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We might enter the secondary CPU capture code twice, eg if we have to
unstick some CPUs with a system reset. In this case we don't want to
overwrite the state on CPUs that had made it into the capture code OK,
so use the cpus_state_saved cpumask for that and make it local to
crash_ipi_callback.
For controlling progress now use atomic_t cpus_in_crash to count how
many CPUs have made it into the kdump code, and time_to_dump to tell
everyone it's time to dump.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we enter the kdump code via system reset, wait a bit before
sending the IPI to capture all secondary CPUs. Without it we race
with the hypervisor that is issuing the system reset to each CPU.
If the IPI gets there first the system reset oops output then shows
the register state of the IPI handler which is not what we want.
I took the opportunity to add defines for all the various delays
we have. There's no need for cpu_relax when we are doing an mdelay,
so remove them too.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I have an intermittent kdump fail where the hypervisor fails an H_EOI.
As a result our CPPR is never reset to 0xff and we no longer accept
interrupts.
This patch calls icp_hv_set_cppr to reset the CPPR if H_EOI fails,
fixing the kdump fail.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We've had a 180 second panic timeout on ppc64 for as long as I
can remember. This patch reduces it to 10 seconds on pseries for a few
reasons:
- Almost all pseries machines have a hypervisor console so panic
output will be available in a scrollback buffer.
- The 180 seconds impacts our availability, users (other than
kernel hackers) just want the box to come back around so it
can continue its work.
- I spend a lot of my life staring at the 180 second panic timeout.
Many pseries machines take minutes to power cycle, so it's quicker
to sit through the 180 seconds than it is to power cycle.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Our die() code was based off a very old x86 version. Update it to
mirror the current x86 code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove some unnecessary defines and fix some spelling mistakes.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul Mackerras