The Aspeed SoCs contain GPIOs banked by letter, where each bank contains
8 pins. The GPIO banks are then grouped in sets of four in the register
layout.
The implementation exposes multiple banks through the one driver and
requests and releases pins via the pinctrl subsystem. The hardware
supports generation of interrupts from all GPIO-capable pins.
A number of hardware features are not yet supported: Configuration of
interrupt direction (ARM or LPC), debouncing, and WDT reset tolerance
for output ports.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add driver for lp873x PMIC family GPOs. Two GPOs are supported
and can be configured in Open-drain output or Push-pull output.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This driver is generic and aims to support all Technologic Systems's
boards embedding FPGA GPIOs with an I2C interface.
This driver supports TS-4900, TS-7970, TS-7990 and TS-4100 series.
Signed-off-by: Lucile Quirion <lucile.quirion@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Diamond Systems GPIO-MM device features 48 lines of digital I/O via
the emulation of dual 82C55A PPI chips. This driver provides GPIO
support for these 48 channels of digital I/O. The base port addresses
for the devices may be configured via the base array module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch introduces a separate GPIO driver for Intel WhiskeyCove PMIC.
This driver is based on gpio-crystalcove.c.
Changes in v7:
- Fixed various coding style comments from Andy Shevchenko
Changes in v6:
- Removed unnecessary wcove_gpio_remove()
- Used devm_gpiochip_remove() instead of gpiochip_remove()
- Various coding style changes per Mika's comment
Changes in v5:
- Revisited the interrupt handler code to iterate until all pending
interrupts are handled. This change is to avoid missing interrupt
when we're inside the interrupt handler.
- Used regmap_bulk_read() to read address adjacent registers.
Changes in v4:
- Converted CTLI_INTCNT_XX macros to less verbose ones INT_DETECT_XX.
- Add comments about why there is no .pm for the driver.
- Header files re-ordered.
- Various coding style change to address Andy's comments.
Changes in v3:
- Fixed the year in copyright line(2015-->2016).
- Removed DRV_NAME macro.
- Added kernel-doc for regmap_irq_chip of the wcove_gpio structure.
- Line length fix.
Changes in v2:
- Typo fix (Whsikey --> Whiskey).
- Included linux/gpio/driver.h instead of linux/gpio.h
- Implemented .set_single_ended().
- Added GPIO register description.
- Replaced container_of() with gpiochip_get_data().
- Removed unnecessary "if (gpio > WCOVE_VGPIO_NUM" check.
- Removed the device id table and added MODULE_ALIAS().
Signed-off-by: Ajay Thomas <ajay.thomas.david.rajamanickam@intel.com>
Signed-off-by: Bin Gao <bin.gao@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AXP209 PMIC has a bunch of GPIOs accessible, that are usually used to
control LEDs or backlight.
Add a driver for them
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Intel Merrifield platform has a special GPIO controller to
drive pads when they are muxed in corresponding mode.
Intel Merrifield GPIO IP is slightly different here and there
in comparison to the older Intel MID platforms. These differences
include in particular the shaked register offsets, specific
support of level triggered interrupts and wake capable sources,
as well as a pinctrl which is a separate IP.
Instead of uglifying existing driver I decide to provide a new
one slightly based on gpio-intel-mid.c. So, anyone can easily
compare what changes are happened to be here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Brian J Wood <brian.j.wood@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MAXIM Semiconductor's PMIC, MAX77620/MAX20024 has 8 GPIO
pins. It also supports interrupts from these pins.
Add GPIO driver for these pins to control via GPIO APIs.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch renames the gpio-generic.c into gpio-mmio.c.
This is because currently the file only contains code
for a memory-mapped GPIO driver. There isn't any support
for ioports or other resource type.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow compile testing this driver by adding a new config option which
is enabled by default and depends on the old symbol or COMPILE_TEST.
Signed-off-by: Alexander Stein <alexanders83@web.de>
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
- New Device Support
- Supply device PCI IDs for Intel Broxton
- Fix-ups
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
- Bug Fixes
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gTBA
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
New Device Support:
- Supply device PCI IDs for Intel Broxton
Fix-ups:
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
Bug Fixes:
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss"
* tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (53 commits)
mfd: intel-lpss: Pass I2C configuration via properties on BXT
mfd: imx6sx: Add PCIe register definitions for iomuxc gpr
mfd: ipaq-micro: Use __maybe_unused to hide pm functions
mfd: max77686: Add max77802 to I2C device ID table
mfd: max77686: Export OF module alias information
mfd: max77686: Allow driver to be built as a module
mfd: stmpe: Add the proper PWM resources
mfd: tps65090: Set regmap config reg counts properly
mfd: syscon: Return ENOTSUPP instead of ENOSYS when disabled
mfd: as3711: Set regmap config reg counts properly
mfd: rc5t583: Set regmap config reg counts properly
gpio: tps65086: Add GPO driver for the TPS65086 PMIC
mfd: mt6397: Add platform device ID table
mfd: da9063: Fix missing volatile registers in the core regmap_range volatile lists
mfd: mt6397: Add MT6323 support to MT6397 driver
mfd: mt6397: Add support for different Slave types
mfd: mt6397: int_con and int_status may vary in location
dt-bindings: mfd: Add bindings for the MediaTek MT6323 PMIC
mfd: da9062: Fix missing volatile registers in the core regmap_range volatile lists
mfd: Add documentation for ACT8945A DT bindings
...
Add support for the TPS65086 PMIC GPOs.
TPS65086 has four configurable GPOs that can be used for several
purposes. These are output only.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The 16Z127 is a 32bit GPIO controller on a MCB FPGA.
Every single line can be configured as input and output.
Push pull and open drain are supported as well as setting
a debounce value for the input lines.
Signed-off-by: Andreas Werner <andy@wernerandy.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Driver for the GPIO block found in ti's tps65218 pmics.
The device has two GPIOs and one GPO pin which can be configured as follows:
GPIO1:
-general-purpose, open-drain output controlled by GPO1 user bit and/or
sequencer
-DDR3 reset input signal from SOC. Signal is either latched or
passed-trough to GPO2 pin. See below for details.
GPO2:
-general-purpose output controlled by GPO2 user bit
-DDR3 reset output signal. Signal is controlled by GPIO1 and PGOOD.
See below for details.
-Output buffer can be configured as open-drain or push-pull.
GPIO3:
-general-purpose, open-drain output controlled by GPO3 user bit and/or
sequencer
-reset input-signal for DCDC1 and DCDC2.
The input configurations are not meant to be used by the user so the driver
only offers GPOs.
v2: Added request routine that evaluates the fw config flags and removed module
owner
v3: Added .direction_input() routine, and took care of all Linus Walleij
suggestions (clamp to bool, use proper include)
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add driver for TI TPIC2810 8-Bit LED Driver with I2C Interface.
The TPIC2810 has 8 open-drain outputs that can but used to drive
LEDs and other low-side switched resistive loads.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add generic parallel-in/serial-out shift register GPIO driver.
This includes SPI compatible devices like SN74165 serial-out shift
registers and the SN65HVS88x series of industrial serializers that can
be read over the SPI bus and used for GPI (General Purpose Input).
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drop most of the code in favor of the generic MMIO GPIO driver.
As the driver now depend on CONFIG_GPIO_GENERIC also add a Kconfig
entry to make the driver optional.
We leave the base pointer and lock in the data struct because they are
needed for the IRQ support.
Signed-off-by: Alban Bedel <albeu@free.fr>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The TS-4800 GPIO driver provide support for the GPIOs available
on the Technologic Sytems board FPGA. It allows to set
direction and read/write states.
It uses the generic gpio driver.
Signed-off-by: Julien Grossholtz <julien.grossholtz@savoirfairelinux.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-DIO-48E device provides 48 lines digital I/O via two
Programmable Peripheral Interface (PPI) chips of type 82C55. Bit C3 at
each 24-bit Group can be used as an external interrupt, triggered by a
rising edge.
This driver provides GPIO and IRQ support for these 48 channels of
digital I/O. The base port address for the device may be configured via
the dio_48e_base module parameter. The interrupt line number for the
device may be configured via the dio_48e_irq module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The WinSystems WS16C48 device provides 48 lines of digital I/O. In
addition, the first 24 lines may be used for interrupt-handled edge
detection; rising edge detection and falling edge detection are
supported.
This driver provides GPIO and IRQ support for these 48 channels of
digital I/O. The base port address for the device may be configured via
the ws16c48_base module parameter. The interrupt line number for the
device may be configured via the ws16c48_irq module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings several
of the more minor and older platforms we have closer to multiplatform
support. Among these are MMP, S3C64xx, Orion5x, mv78xx0 and realview
Much of this is moving around header files from old mach directories,
but there are also some cleanup patches of debug_ll (lowlevel debug
per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z1AW
-----END PGP SIGNATURE-----
Merge tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform code updates from Arnd Bergmann:
"This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings
several of the more minor and older platforms we have closer to
multiplatform support. Among these are MMP, S3C64xx, Orion5x, mv78xx0
and realview Much of this is moving around header files from old mach
directories, but there are also some cleanup patches of debug_ll
(lowlevel debug per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts"
* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (75 commits)
ARM: realview: don't select SMP_ON_UP for UP builds
ARM: s3c: simplify s3c_irqwake_{e,}intallow definition
ARM: s3c64xx: fix pm-debug compilation
iio: exynos-adc: fix irqf_oneshot.cocci warnings
ARM: realview: build realview-dt SMP support only when used
ARM: realview: select apropriate targets
ARM: realview: clean up header files
ARM: realview: make all header files local
ARM: no longer make CPU targets visible separately
ARM: integrator: use explicit core module options
ARM: realview: enable multiplatform
ARM: make default platform work for NOMMU
ARM: debug-ll: move DEBUG_LL_UART_EFM32 to correct Kconfig location
ARM: defconfig: use correct debug_ll settings
ARM: versatile: convert to multi-platform
ARM: versatile: merge mach code into a single file
ARM: versatile: switch to DT only booting and remove legacy code
ARM: versatile: add DT based PCI detection
ARM: pxa: mark ezx structures as __maybe_unused
ARM: pxa: mark raumfeld init functions as __maybe_unused
...
The gpio-samsung driver is special in the sense that it
interacts directly in multiple ways with the legacy platform
code for the s3c24xx and s3c64xx platforms. In contrast,
all devicetree based machines for Samsung, including the
ones on those two SoC families use a different driver.
The header files that define the interface between the platform
code and the gpio driver are not visible when building a
kernel for ARCH_MULTIPLATFORM, which prevents us from
turning on this option for s3c64xx.
To work around this, we now move the driver back into platform
code, from where it was originally moved to as part of commit
1b39d5f2cc ("gpio/samsung: gpio-samsung.c to support
Samsung GPIOs").
The long-term plan for this driver would be to remove it
entirely, after all Samsung machines have been converted
over to boot from DT, but there is currently no timeline
for when that might happen.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The ACCES 104-IDI-48 family of PC/104 utility boards feature 48
individually optically isolated digital inputs. Enabled inputs feature
change-of-state detection capability; if change-of-state detection is
enabled, an interrupt is fired off if a change of input level
(low-to-high or high-to-low) is detected. Change-of-state IRQs are
enabled/disabled on 8-bit boundaries, for a total of six boundaries.
This driver provides GPIO and IRQ support for these 48 channels of
digital input. The base port address for the device may be configured
via the idi_48_base module parameter. The interrupt line number for the
device may be configured via the idi_48_irq module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-IDIO-16 family of PC/104 utility boards feature 16
optically isolated inputs and 16 optically isolated FET solid state
outputs. This driver provides GPIO support for these 32 channels of
digital I/O. Change-of-State detection interrupts are not supported.
GPIO 0-15 correspond to digital outputs 0-15, while GPIO 16-31
correspond to digital inputs 0-15. The base port address for the device
may be set via the idio_16_base module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for the GPIOs found on the ITE super-I/O chips
IT87xx.
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.eu>
Signed-off-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove this driver now that Bjorn has introduced a pinctrl driver
for msm8660 and the dts files have been updated with the pinctrl
compatibles.
Cc: Andy Gross <agross@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Root out the wrapper devm_gpiod_get() and gpiod_get() etc
versions of the descriptor calls that did not use the flags
argument on the end. This was around for too long and eventually
Uwe Kleine-König took the time to clean it out and the last
users are removed along with the macros in this tag. In several
cases the use of flags simplifies the code. For this reason we
have (ACKed) patches hitting in DRM, IIO, media, NFC, USB+PHY
up until we hammer in the nail with removing the macros.
- Add a fat document describing how much ready-made GPIO stuff
we have i the kernel to discourage people from reinventing
a square wheel in userspace, as so often happens.
- Create a separate lockdep class for each instance of a GPIO
IRQ chip instead of using one class for all chips, as the current
code will not work with systems with several GPIO chips doing
lockdep debugging.
- Protect against driver unloading also when a GPIO line is only
used as IRQ for the GPIOLIB_IRQCHIP helpers.
- If the GPIO chip has no designated owner, assign the parent
device driver owner as owner.
- Consolidation of chained IRQ handler install/remove replacing
all call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a
combined call to irq_set_chained_handler_and_data(). This
series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which
is way cleaner.
- Tglx and Jiang Liu wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs
from IRQ numbers. The goal is to get rid of the irq number
from the handlers in the IRQ flow which is nice.
- Rob Herring killed off the set_irq_flags() for all GPIO
drivers. This was an ARM specific function that is replaced
with the generic irq_modify_status() where special flags
are actually needed.
- When an OF node has a pin range for its GPIOs, return
-EPROBE_DEFER if the pin controller isn't available.
Pretty logical, yet needed to be fixed.
- If a driver using GPIOLIB_IRQCHIP has its own
irq_*_resources call back, then call these instead of the
defaults provided by the GPIOLIB.
- Fix an undocumented ABI hole: named GPIOs were not
properly documented.
Driver improvements:
- Add get_direction() support to the generic GPIO driver, it's
strange that we didn't have that before.
- Make it possible to have input-only GPIO chips using the
generic GPIO driver.
- Clean out platform data support from the Emma Mobile (EM)
driver
- Finegrained runtime PM support for the RCAR driver.
- Support r8a7795 (R-car H3) in the RCAR driver.
- Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.
- Some consolidation and new support in the MPC8xxx driver,
we now support MPC5125.
- Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
spinlocks making it work better with the realime patches.
- Interrupt support for the EXTRAXFS GPIO driver.
- Make the ETRAXFS GPIO driver support also ARTPEC-3.
- Interrupt and wakeup support for the BRCMSTB driver, also for
wakeup from S5 cold boot.
- Mask MXC IRQs during suspend.
- Improve OMAP2 GPIO set_debounce() to work according to spec.
- The VF610 driver handles IRQs properly.
New drivers:
- ZTE ZX GPIO driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iQ2P
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.3 kernel cycle.
There is quite a lot going on in the GPIO subsystem this merge window,
so the main matter is decribed below.
The hits in other subsystems when making the GPIO flags optional are
all ACKed by their respective subsystem maintainers.
Core changes:
- Root out the wrapper devm_gpiod_get() and gpiod_get() etc versions
of the descriptor calls that did not use the flags argument on the
end. This was around for too long and eventually Uwe Kleine-König
took the time to clean it out and the last users are removed along
with the macros in this tag. In several cases the use of flags
simplifies the code. For this reason we have (ACKed) patches
hitting in DRM, IIO, media, NFC, USB+PHY up until we hammer in the
nail with removing the macros.
- Add a fat document describing how much ready-made GPIO stuff we
have i the kernel to discourage people from reinventing a square
wheel in userspace, as so often happens.
- Create a separate lockdep class for each instance of a GPIO IRQ
chip instead of using one class for all chips, as the current code
will not work with systems with several GPIO chips doing lockdep
debugging.
- Protect against driver unloading also when a GPIO line is only used
as IRQ for the GPIOLIB_IRQCHIP helpers.
- If the GPIO chip has no designated owner, assign the parent device
driver owner as owner.
- Consolidation of chained IRQ handler install/remove replacing all
call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a combined
call to irq_set_chained_handler_and_data().
This series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which is
way cleaner.
- Tglx and Jiang Liu wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs from
IRQ numbers. The goal is to get rid of the irq number from the
handlers in the IRQ flow which is nice.
- Rob Herring killed off the set_irq_flags() for all GPIO drivers.
This was an ARM specific function that is replaced with the generic
irq_modify_status() where special flags are actually needed.
- When an OF node has a pin range for its GPIOs, return -EPROBE_DEFER
if the pin controller isn't available. Pretty logical, yet needed
to be fixed.
- If a driver using GPIOLIB_IRQCHIP has its own irq_*_resources call
back, then call these instead of the defaults provided by the
GPIOLIB.
- Fix an undocumented ABI hole: named GPIOs were not properly
documented.
Driver improvements:
- Add get_direction() support to the generic GPIO driver, it's
strange that we didn't have that before.
- Make it possible to have input-only GPIO chips using the generic
GPIO driver.
- Clean out platform data support from the Emma Mobile (EM) driver
- Finegrained runtime PM support for the RCAR driver.
- Support r8a7795 (R-car H3) in the RCAR driver.
- Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.
- Some consolidation and new support in the MPC8xxx driver, we now
support MPC5125.
- Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
spinlocks making it work better with the realime patches.
- Interrupt support for the EXTRAXFS GPIO driver.
- Make the ETRAXFS GPIO driver support also ARTPEC-3.
- Interrupt and wakeup support for the BRCMSTB driver, also for
wakeup from S5 cold boot.
- Mask MXC IRQs during suspend.
- Improve OMAP2 GPIO set_debounce() to work according to spec.
- The VF610 driver handles IRQs properly.
New drivers:
- ZTE ZX GPIO driver"
* tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
Revert "gpio: extraxfs: fix returnvar.cocci warnings"
gpio: tc3589x: use static container helper
gpio: xlp: fix error return code
gpio: vf610: handle level IRQ's properly
gpio: max732x: Fix error handling in probe()
gpio: omap: fix clk_prepare/unprepare usage
gpio: omap: protect regs access in omap_gpio_irq_handler
gpio: omap: fix omap2_set_gpio_debounce
gpio: omap: switch to use platform_get_irq
gpio: omap: remove wrong irq_domain_remove usage in probe
gpiolib: add description for gpio irqchip fields in struct gpio_chip
gpio: extraxfs: fix returnvar.cocci warnings
gpiolib: irqchip: use different lockdep class for each gpio irqchip
gpio/grgpio: fix deadlock in grgpio_irq_unmap()
Documentation: gpio: consumer: describe active low property
gpio: mxc: fix section mismatch warning
gpio/mxc: mask gpio interrupts in suspend
gpio: omap: Fix missing raw locks conversion
gpio: brcmstb: support wakeup from S5 cold boot
gpio: brcmstb: Add interrupt and wakeup source support
...
Add a GPIO driver for the General I/O block on Axis ETRAX FS SoCs.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the GPIO IP "UPG GIO" used on
Broadcom STB SoCs (BCM7XXX and some others). Uses
basic_mmio_gpio to instantiate a gpio_chip for each bank.
The driver assumes that it handles the base set of GPIOs
on the system and that it can start its numbering sequence
from 0, so any GPIO expanders used with it must dynamically
assign GPIO numbers after this driver has finished
registering its GPIOs.
Does not implement the interrupt-controller portion yet,
will be done in a future commit.
v2:
- change include to use <linux/gpio/driver.h> instead of
<linux/gpio.h>
- get rid of unnecessary imask member in struct bank
- rename GPIO_PER_BANK -> MAX_GPIO_PER_BANK
- always have 32 GPIOs per bank and add 'width' member in
struct bank to hold actual number of GPIOs in use
- mark of_match table as const
List-usage-fixed-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add GPIO controller driver for Netlogic XLP MIPS64 SOCs.
This driver is instantiated by device tree and supports interrupts
for GPIOs.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Driver for the GPIO block found on NXP LPC18xx/43xx devices.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We've got a fairly large cleanup branch this time. The bulk of this is removal
of non-DT platforms of several flavors:
- Atmel at91 platforms go full-DT, with removal of remaining board-file based
support
- OMAP removes legacy board files for three more platforms
- Removal of non-DT mach-msm, newer Qualcomm platforms now live in mach-qcom
- Freescale i.MX25 also removes non-DT platform support
Most of the rest of the changes here are fallout from the above, i.e. for
example removal of drivers that now lack platforms, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BV8A
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"We've got a fairly large cleanup branch this time. The bulk of this
is removal of non-DT platforms of several flavors:
- Atmel at91 platforms go full-DT, with removal of remaining
board-file based support
- OMAP removes legacy board files for three more platforms
- removal of non-DT mach-msm, newer Qualcomm platforms now live in
mach-qcom
- Freescale i.MX25 also removes non-DT platform support"
Most of the rest of the changes here are fallout from the above, i.e. for
example removal of drivers that now lack platforms, etc.
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (58 commits)
mmc: Remove msm_sdcc driver
gpio: Remove gpio-msm-v1 driver
ARM: Remove mach-msm and associated ARM architecture code
ARM: shmobile: cpuidle: Remove the pointless default driver
ARM: davinci: dm646x: Add interrupt resource for McASPs
ARM: davinci: irqs: Correct McASP1 TX interrupt definition for DM646x
ARM: davinci: dm646x: Clean up the McASP DMA resources
ARM: davinci: devices-da8xx: Add support for McASP2 on da830
ARM: davinci: devices-da8xx: Clean up and correct the McASP device creation
ARM: davinci: devices-da8xx: Add interrupt resource to McASP structs
ARM: davinci: devices-da8xx: Add resource name for the McASP DMA request
ARM: OMAP2+: Remove legacy support for omap3 TouchBook
ARM: OMAP3: Remove legacy support for devkit8000
ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
ARM: shmobile: Consolidate the pm code for R-Car Gen2
ARM: shmobile: r8a7791: Correct SYSCIER value
ARM: shmobile: r8a7790: Correct SYSCIER value
ARM: at91: remove old setup
ARM: at91: sama5d4: remove useless map_io
ARM: at91: sama5 use SoC detection infrastructure
...
This driver is orphaned now that mach-msm has been removed.
Delete it.
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Adds a new driver for Altera soft GPIO IP. The driver is able to do
read/write and allows GPIO to be a interrupt controller.
Tested on Altera GHRD on interrupt handling and IO.
v10:
- Updated conflicting device tree parameters
- Removed unused headers
- Used macro instead of magic numbers for ngpio
- Code readability cleanup using ?: and temporal variables
- Removed leftover garbage and unnecessary function calls
- Checked bgpio_init but unusable because Altera GPIO may not
be a multiple of 8 bits
v9:
- Removed duplicated initialization on set_type using temporals
to improve code readability in calling generic_handle_irq
- Using ?: ternary to reduce code size
v8:
- Using for_each_set_bit
- Added const for struct definition
- Removed naggy pr_err
- Sort alpha header
- Remove unused macros
- Use fixed width data types instead of unsigned long
- Whitespace issue fixes
- Removed _relaxed function for better compatibility across different
CPU
- Changed irq_create_mapping to platform_get_irq updated implementation
to use gpiochip_irqchip_add
- Reserve interrupt-cells number 2 in device tree binding for future
use
- Remove confusing sections on devicetree bindings
- Added tristate Kconfig help text
v7:
- Used dev_warn instead of pr_warn
- Clean up unnecesarry if else indentation
v6:
- Added irq_startup and irq_shutdown
- Changed bitwise clamping style
- Cleanup bitwise operation to improve readability change naming of
mapped irqs from virq to mapped_irq
v5:
- Dispose irq_domain mapping correctly
- Update optional binding description in binding docs
v4:
- Added vendor prefix to devicetree binding for IP specific properties
using MMIO GPIO helper library instead of manually map PIO to memory
- altera_gpio_chip inline struct documentation to kerneldoc
- Using dev_ print to print a better failure message
v2, v3:
- Do not reference NO_IRQ
- Updated irq_set_type to only allow the hardware configured irq type
Signed-off-by: Tien Hock Loh <thloh@altera.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Driver for Fujitsu MB86S7x SoCs that have a memory mapped GPIO controller.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com>
Signed-off-by: Tetsuya Nuriya <nuriya.tetsuya@jp.fujitsu.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Driver for standby GPIO controller of APM X-Gene SoCs on arm64.
Signed-off-by: Y Vo <yvo@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- A new API that allows setting more than one GPIO at the
time. This is implemented for the new descriptor-based
API only and makes it possible to e.g. toggle a clock and
data line at the same time, if the hardware can do this
with a single register write. Both consumers and drivers
need new calls, and the core will fall back to driving
individual lines where needed. Implemented for the MPC8xxx
driver initially.
- Patched the mdio-mux-gpio and the serial mctrl driver
that drives modems to use the new multiple-setting API
to set several signals simultaneously.
- Get rid of the global GPIO descriptor array, and instead
allocate descriptors dynamically for each GPIO on a certain
GPIO chip. This moves us closer to getting rid of the
limitation of using the global, static GPIO numberspace.
- New driver and device tree bindings for 74xx ICs.
- New driver and device tree bindings for the VF610 Vybrid.
- Support the RCAR r8a7793 and r8a7794.
- Guidelines for GPIO device tree bindings trying to get
things a bit more strict with the advent of combined
device properties.
- Suspend/resume support for the MVEBU driver.
- A slew of minor fixes and improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZAhA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull take two of the GPIO updates:
"Same stuff as last time, now with a fixup patch for the previous
compile error plus I ran a few extra rounds of compile-testing.
This is the bulk of GPIO changes for the v3.19 series:
- A new API that allows setting more than one GPIO at the time. This
is implemented for the new descriptor-based API only and makes it
possible to e.g. toggle a clock and data line at the same time, if
the hardware can do this with a single register write. Both
consumers and drivers need new calls, and the core will fall back
to driving individual lines where needed. Implemented for the
MPC8xxx driver initially
- Patched the mdio-mux-gpio and the serial mctrl driver that drives
modems to use the new multiple-setting API to set several signals
simultaneously
- Get rid of the global GPIO descriptor array, and instead allocate
descriptors dynamically for each GPIO on a certain GPIO chip. This
moves us closer to getting rid of the limitation of using the
global, static GPIO numberspace
- New driver and device tree bindings for 74xx ICs
- New driver and device tree bindings for the VF610 Vybrid
- Support the RCAR r8a7793 and r8a7794
- Guidelines for GPIO device tree bindings trying to get things a bit
more strict with the advent of combined device properties
- Suspend/resume support for the MVEBU driver
- A slew of minor fixes and improvements"
* tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (33 commits)
gpio: mcp23s08: fix up compilation error
gpio: pl061: document gpio-ranges property for bindings file
gpio: pl061: hook request if gpio-ranges avaiable
gpio: mcp23s08: Add option to configure IRQ output polarity as active high
gpio: fix deferred probe detection for legacy API
serial: mctrl_gpio: use gpiod_set_array function
mdio-mux-gpio: Use GPIO descriptor interface and new gpiod_set_array function
gpio: remove const modifier from gpiod_get_direction()
gpio: remove gpio_descs global array
gpio: mxs: implement get_direction callback
gpio: em: Use dynamic allocation of GPIOs
gpio: Check if base is positive before calling gpio_is_valid()
gpio: mcp23s08: Add simple IRQ support for SPI devices
gpio: mcp23s08: request a shared interrupt
gpio: mcp23s08: Do not free unrequested interrupt
gpio: rcar: Add r8a7793 and r8a7794 support
gpio-mpc8xxx: add mpc8xxx_gpio_set_multiple function
gpiolib: allow simultaneous setting of multiple GPIO outputs
gpio: mvebu: add suspend/resume support
gpio: gpio-davinci: remove duplicate check on resource
..
This patch adds GPIO and IRQ support for the Diolan DLN-2 GPIO module.
Information about the USB protocol interface can be found in the
Programmer's Reference Manual [1], see section 2.9 for the GPIO
module commands and responses.
[1] https://www.diolan.com/downloads/dln-api-manual.pdf
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add a gpiolib and IRQ chip driver for Vybrid ARM SoC using the
Vybrid's GPIO and PORT module. The driver is instanced once per
each GPIO/PORT module pair and handles 32 GPIO's.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle, and this time we got a lot of action going on and
it will continue:
- The core GPIO library implementation has been split up in
three different files:
- gpiolib.c for the latest and greatest and shiny GPIO
library code using GPIO descriptors only
- gpiolib-legacy.c for the old integer number space API
that we are phasing out gradually
- gpiolib-sysfs.c for the sysfs interface that we are
not entirely happy with, but has to live on for
ABI compatibility
- Add a flags argument to *gpiod_get* functions, with some
backward-compatibility macros to ease transitions. We
should have had the flags there from the beginning it
seems, now we need to clean up the mess. There is a plan
on how to move forward here devised by Alexandre Courbot
and Mark Brown.
- Split off a special <linux/gpio/machine.h> header for the
board gpio table registration, as per example from the
regulator subsystem.
- Start to kill off the return value from gpiochip_remove()
by removing the __must_check attribute and removing all
checks inside the drivers/gpio directory. The rationale
is: well what were we supposed to do if there is an error
code? Not much: print an error message. And gpiolib already
does that. So make this function return void eventually.
- Some cleanups of hairy gpiolib code, make some functions
not to be used outside the library private and make sure
they are not exported, remove gpiod_lock/unlock_as_irq()
as the existing function is for driver-internal use and
fine as it is, delete gpio_ensure_requested() as it is
not meaningful anymore.
- Support the GPIOF_ACTIVE_LOW flag from gpio_request_one()
function calls, which is logical since this is already
supported when referencing GPIOs from e.g. device trees.
- Switch STMPE, intel-mid, lynxpoint and ACPI (!) to use
the gpiolib irqchip helpers cutting down on GPIO irqchip
boilerplate a bit more.
- New driver for the Zynq GPIO block.
- The usual incremental improvements around a bunch of
drivers.
- Janitorial syntactic and semantic cleanups by Jingoo Han,
and Rickard Strandqvist especially.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=e+d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO update from Linus Walleij:
"This is the bulk of GPIO changes for the v3.17 development cycle, and
this time we got a lot of action going on and it will continue:
- The core GPIO library implementation has been split up in three
different files:
- gpiolib.c for the latest and greatest and shiny GPIO library code
using GPIO descriptors only
- gpiolib-legacy.c for the old integer number space API that we are
phasing out gradually
- gpiolib-sysfs.c for the sysfs interface that we are not entirely
happy with, but has to live on for ABI compatibility
- Add a flags argument to *gpiod_get* functions, with some
backward-compatibility macros to ease transitions. We should have
had the flags there from the beginning it seems, now we need to
clean up the mess. There is a plan on how to move forward here
devised by Alexandre Courbot and Mark Brown
- Split off a special <linux/gpio/machine.h> header for the board
gpio table registration, as per example from the regulator
subsystem
- Start to kill off the return value from gpiochip_remove() by
removing the __must_check attribute and removing all checks inside
the drivers/gpio directory. The rationale is: well what were we
supposed to do if there is an error code? Not much: print an error
message. And gpiolib already does that. So make this function
return void eventually
- Some cleanups of hairy gpiolib code, make some functions not to be
used outside the library private and make sure they are not
exported, remove gpiod_lock/unlock_as_irq() as the existing
function is for driver-internal use and fine as it is, delete
gpio_ensure_requested() as it is not meaningful anymore
- Support the GPIOF_ACTIVE_LOW flag from gpio_request_one() function
calls, which is logical since this is already supported when
referencing GPIOs from e.g. device trees
- Switch STMPE, intel-mid, lynxpoint and ACPI (!) to use the gpiolib
irqchip helpers cutting down on GPIO irqchip boilerplate a bit more
- New driver for the Zynq GPIO block
- The usual incremental improvements around a bunch of drivers
- Janitorial syntactic and semantic cleanups by Jingoo Han, and
Rickard Strandqvist especially"
* tag 'gpio-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (37 commits)
MAINTAINERS: update GPIO include files
gpio: add missing includes in machine.h
gpio: add flags argument to gpiod_get*() functions
MAINTAINERS: Update Samsung pin control entry
gpio / ACPI: Move event handling registration to gpiolib irqchip helpers
gpio: lynxpoint: Convert to use gpiolib irqchip
gpio: split gpiod board registration into machine header
gpio: remove gpio_ensure_requested()
gpio: remove useless check in gpiolib_sysfs_init()
gpiolib: Export gpiochip_request_own_desc and gpiochip_free_own_desc
gpio: move gpio_ensure_requested() into legacy C file
gpio: remove gpiod_lock/unlock_as_irq()
gpio: make gpiochip_get_desc() gpiolib-private
gpio: simplify gpiochip_export()
gpio: remove export of private of_get_named_gpio_flags()
gpio: Add support for GPIOF_ACTIVE_LOW to gpio_request_one functions
gpio: zynq: Clear pending interrupt when enabling a IRQ
gpio: drop retval check enforcing from gpiochip_remove()
gpio: remove all usage of gpio_remove retval in driver/gpio
devicetree: Add Zynq GPIO devicetree bindings documentation
...
Add support for GPIO controller used by Xilinx Zynq.
v3 changes:
- Use linux/gpio/driver.h instead of linux/gpio.h
- Make irq a local variable in probe
v2 changes:
- convert to pm_runtime_force_(suspend|resume)
- add pm_runtime_set_active in probe()
- also (un)prepare clocks when they are dis-/enabled
- add some missing calls to pm_runtime_get()
- use pm_runtime_put() instead of sync variant
- remove gpio chip in driver remove()
- remove redundant type casts
- directly use IO helpers
- use BIT macro to set/clear bits
- migrate to GPIOLIB_IRQCHIP
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The old integer GPIO interface is, in effect, a privileged user of the
gpiod interface. Reflect this fact further by moving legacy GPIO support
into its own source file. This makes the code clearer and will allow us
to disable legacy GPIO support in the (far) future.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
sysfs support is currently entangled within the core GPIO support, while
it should relly just be a (privileged) user of the integer GPIO API.
This patch is a first step towards making the gpiolib code more readable
by splitting it into logical parts.
Move all sysfs support to their own source file, and share static
members of gpiolib that need to be in the private gpiolib.h file. In
the future we will want to put some of them back into gpiolib.c, but this
first patch let us at least identify them.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Devices based on Intel SoC products such as Baytrail have a Power
Management IC. In the PMIC there are subsystems for voltage regulation,
A/D conversion, GPIO and PWMs. The PMIC in Baytrail-T platform is
called Crystal Cove.
This patch adds support for the GPIO function in Crystal Cove.
Signed-off-by: Yang, Bin <bin.yang@intel.com>
Signed-off-by: Zhu, Lejun <lejun.zhu@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ARCH_OMAP config option was used to built the GPIO OMAP
driver but this is not consistent with the rest of the GPIO
drivers that have their own Kconfig option.
Also, this make it harder to add dependencies or reverse
dependencies (i.e: select) since that would mean touching the
sub-arch config option.
So is better to add a boolean Kconfig option for this driver
that defaults to true if ARCH_OMAP is enabled.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
SYSCON driver was designed for using memory areas (registers)
that are used in several subsystems. There are systems (CPUs)
which use bits in one register for various purposes and thus
should be handled by various kernel subsystems. This driver
allows you to use the individual SYSCON bits as GPIOs.
ARM CLPS711X SYSFLG1 input lines has been added as first user
of this driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The tnetv107x platform is getting removed, so this driver won't
be needed any more.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Synopsys DesignWare block is used in some ARM devices (picoxcell)
and can be configured to provide multiple banks of GPIO pins.
v12: - Add irq_startup/shutdown
- do irq_create_mapping() in probe, irq_find_mapping() in to_irq()
- Adjust mappings to show support for 1 gpio per port.
- gpio-cells = <1>
v11: - Use NULL when checking existence of 'interrupts' property
- Bindings descriptions cleanup
v10: - in documentation nr-gpio -> nr-gpios
v9: - cleanup in dt bindings doc
- use of_get_child_count()
v8: - remove socfpga.dtsi changes
- minor cleanup in devicetree documentation
v7: - use irq_generic_chip
- support one irq per gpio line or one irq for many
- s/bank/port/ and other cleanup
v6: - (atull) squash the set of patches
- use linear irq domain
- build fixes. Original driver was reviewed on v3.2.
- Fix setting irq edge type for 'rising' and 'both'.
- Support as a loadable module.
- Use bgpio_chip's spinlock during register access.
- Clean up register names to match spec
- s/bank/port/ because register names use the word 'port'
- s/nr-gpio/nr-gpios/
- don't get/put the of_node
- remove signoffs/acked-by's because of changes
- other cleanup
v5: - handle sparse bank population correctly
v3: - depend on rather than select IRQ_DOMAIN
- split IRQ support into a separate patch
v2: - use Rob Herring's irqdomain in generic irq chip patches
- use reg property to indicate bank index
- support irqs on both edges based on LinusW's u300 driver
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Alan Tull <atull@altera.com>
Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver supports the GPIO controller found in LSI ZEVIO SoCs.
It has been successfully tested on a TI nspire CX calculator.
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Updates of SoC-near drivers and other driver updates that makes more sense to
take through our tree.
The largest part of this is a conversion of device registration for some
renesas shmobile/sh devices over to use resources. This has required
coordination with the corresponding arch/sh changes, and we've agreed
to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure firmware,
which is what is used on many of the commercial Nvidia Tegra products
that are in the market, including the Nvidia Shield. The code is local
to arch/arm at this time since it's uncertain whether it will be shared
with arm64 longer-term, if needed we will refactor later.
A couple of new RTC drivers used on ARM boards, merged through our tree
on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJS4ViqAAoJEIwa5zzehBx3m4QP/07VXVE77RFRyly5Bky5AaMY
zo7ZpoJyg/IT9lxtSAQDhbQq49tKZQVS16oJ7LWXzjAyCY9XrVDX2IkcuqudmYSy
Xtx+R0jZGK4czqljgjwdHgNCSwugCmO/kgNY3h8ar53dTmGIFiq5boPeMDizRTGD
g3sgYuQbIqepcHd2jUjJSBXNyvZIlwBJ4wDyZgxRfzyM7unS8T46BpYNJz0esAL+
0DwIk0nv1eJ6LI0aEL+7bgFaitjUNLpcrroToi1IiIEJuTvZY4AuBjAKt5/181zL
i1ugimsHahmbwNclAmUimc0rtW4Nn+YHGa8WpYiQ9O7+kPFsYkfLRplHPOjaUBPz
r76ucgBMGH6i04tvstwlONznO4NhkACWmb4wrfJfRoDTglELLoOd6QGAYKyRublH
SnrKKmuXzBvtmj2zgUU+S0ka9LdYrjzxoSYprrXQpDr89pUs/AZrlAm9yRjQ3hGw
0eL9UsDFtYAQwCQtPvin2bjKRgNNDbgdwNYNbA7n8jvE/uZ4rlYr3Ot+oxdfs75e
K4fY6JwtbZxQVcOU25M3WBYXLl0V61ZISFa16XhYC2hjzgMZ3bfmFUn+TW9C8V4V
03QqtFyT3FP+VfA3QUS3PuBxALT0HWXmDqp0VJc6UCiXX2InWR+uZQp7a30EawOZ
WHLqgf+nT3bD3kfagCZN
=JJlw
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM driver updates from Olof Johansson:
"Updates of SoC-near drivers and other driver updates that makes more
sense to take through our tree.
The largest part of this is a conversion of device registration for
some renesas shmobile/sh devices over to use resources. This has
required coordination with the corresponding arch/sh changes, and
we've agreed to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure
firmware, which is what is used on many of the commercial Nvidia Tegra
products that are in the market, including the Nvidia Shield. The
code is local to arch/arm at this time since it's uncertain whether it
will be shared with arm64 longer-term, if needed we will refactor
later.
A couple of new RTC drivers used on ARM boards, merged through our
tree on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
watchdog: davinci: rename platform driver to davinci-wdt
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
...
New drivers
- Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and Battery Charger
- TI/National Semiconductor LP3943 I2C GPIO Expander and PWM Generator
Existing driver adaptions
- Expansion of Wolfson Arizona DSP and High-Pass filter controls
- TI TWL6040 default Regmap support and Regcache addition/bypass
- Some nice Smatch catch fixes
- Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
- ChromeOS EC timing (delay) adaptions and added dependency on OF
- Many constifications of 'struct {mfd_cell,regmap_irq,et. al}'
- Watchdog support added for NVIDIA AS3722
- Convert functions to static in TI AM335x
- Realigned previously defeated functionality in TI AM335x
- IIO ADC-TSC concurrency dead-lock/timeout resolution
- Addition of Power Management and Clock support for Samsung core
- DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
- Greater use of irqdomain functionality in ST-E AB8500
- Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
- Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
- Device Tree documentation added for TI/Nat Semi LP3943
- Version detection and voltage tables for TI TPS6586x PMIC devices
- Simplification of Freescale MC13XXX (de-)initialisation routines
- Clean-up and simplification of the Realtek parent driver
- Added support for RTL8402 Realtek PCI-Express card reader
- Resource leak fix for Maxim 77686
- Possible suspend BUG() fix in OMAP USB TLL
- Support for new Wolfson WM5110 Revision (D)
- Testing of automatic assignment of of_node in mfd_add_device()
- Reversion of the above when it started to cause issues
- Remove legacy Platform Data from;
TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
- Clean-ups; tabbing issues, function name changes, 'drvdata = NULL' removal,
unused uninitialised warning mitigation, error message clarity,
removal of redundant/duplicate checks, licensing (GPL -> GPL2),
coding consistency, duplicate function declaration, ret checks,
commit corrections, redundant of_match_ptr() helper removal,
spelling, #if-deffery removal and header guards name changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=PuTE
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd
Pull MFD changes from Lee Jones:
"New drivers
- Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and
Battery Charger
- TI/National Semiconductor LP3943 I2C GPIO Expander and PWM
Generator
Existing driver adaptions
- Expansion of Wolfson Arizona DSP and High-Pass filter controls
- TI TWL6040 default Regmap support and Regcache addition/bypass
- Some nice Smatch catch fixes
- Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
- ChromeOS EC timing (delay) adaptions and added dependency on OF
- Many constifications of 'struct {mfd_cell,regmap_irq,et.al}'
- Watchdog support added for NVIDIA AS3722
- Convert functions to static in TI AM335x
- Realigned previously defeated functionality in TI AM335x
- IIO ADC-TSC concurrency dead-lock/timeout resolution
- Addition of Power Management and Clock support for Samsung core
- DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
- Greater use of irqdomain functionality in ST-E AB8500
- Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
- Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
- Device Tree documentation added for TI/Nat Semi LP3943
- Version detection and voltage tables for TI TPS6586x PMIC devices
- Simplification of Freescale MC13XXX (de-)initialisation routines
- Clean-up and simplification of the Realtek parent driver
- Added support for RTL8402 Realtek PCI-Express card reader
- Resource leak fix for Maxim 77686
- Possible suspend BUG() fix in OMAP USB TLL
- Support for new Wolfson WM5110 Revision (D)
- Testing of automatic assignment of of_node in mfd_add_device()
- Reversion of the above when it started to cause issues
- Remove legacy Platform Data from;
TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
- Clean-ups; tabbing issues, function name changes, 'drvdata = NULL'
removal, unused uninitialised warning mitigation, error
message clarity, removal of redundant/duplicate checks,
licensing (GPL -> GPL2), coding consistency, duplicate
function declaration, ret checks, commit corrections,
redundant of_match_ptr() helper removal, spelling,
#if-deffery removal and header guards name changes"
* tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd: (78 commits)
mfd: wm5110: Add register patch for rev D chip
mfd: omap-usb-tll: Don't hold lock during pm_runtime_get/put_sync()
gpio: lp3943: Remove redundant of_match_ptr helper
mfd: sta2x11-mfd: Use named constants for pci_power_t values
Documentation: mfd: Fix LDO index in s2mps11.txt
mfd: Cleanup mfd-mcp-sa11x0.h header
mfd: max8997: Use "IS_ENABLED(CONFIG_OF)" for DT code.
mfd: twl6030: Fix endianness problem in IRQ handler
mfd: sec-core: Add cells for S5M8767-clocks
mfd: max14577: Remove redundant of_match_ptr helper
mfd: twl6040: Fix sparse non static symbol warning
mfd: Revert "mfd: Always assign of_node in mfd_add_device()"
mfd: rtsx: Fix sparse non static symbol warning
mfd: max77693: Set proper maximum register for MUIC regmap
mfd: max77686: Fix regmap resource leak on driver remove
mfd: Represent correct filenames in file headers
mfd: rtsx: Add support for card reader rtl8402
mfd: rtsx: Add set pull control macro and simplify rtl8411
mfd: max8997: Enforce mfd_add_devices() return value check
mfd: mc13xxx: Simplify probe() & remove()
...
This is one of LP3943 MFD driver.
LP3943 is configurable as a GPIO expander, up to 16 GPIOs.
* Application note: how to configure LP3943 as a GPIO expander
http://www.ti.com/lit/an/snva287a/snva287a.pdf
* Supported GPIO controller operations
request, free, direction_input, direction_output, get and set
* GPIO direction register not supported
LP3943 doesn't have the GPIO direction register. It only provides input and
output status registers.
So, private data for the direction should be handled manually.
This variable is updated whenever the direction is changed and
used in 'get' operation.
* Pin assignment
A driver data, 'pin_used' is checked when a GPIO is requested.
If the GPIO is already assigned, then returns as failure.
If the GPIO is available, 'pin_used' is set.
When the GPIO is not used anymore, then it is cleared.
It is defined as unsigned long type for atomic bit operation APIs,
but only LSB 16bits are used because LP3943 has 16 outputs.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The compatible to Davinci GPIO HW block is used by other TI SoCs, like
Keystone, where GPIO support is declared as optional.
Hence, introduce GPIO_DAVINCI Kconfig option which will allow to enable
Davinci GPIO driver for Keystone SoCs when needed. At same time, kept
Davinci GPIO driver enabled for Davinci SoCs by default.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This patch adds support for the GPIOs found on the SMSC "Super I/
SCH311x.
The chip detection and I/O functions are copied from sch311x_wdt.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO32 is a standard optional extension to the Xtensa architecture
core that provides preconfigured output and input ports for intra
SoC signaling. The GPIO32 option is implemented as 32bit Tensilica
Instruction Extension (TIE) output state called EXPSTATE, and 32bit
input wire called IMPWIRE. This driver treats input and output
states as two distinct devices.
v3:
* Use BUG() in xtensa_impwire_set_value() to indicate that
it should never be called (Linus Walleij)
v2:
* Address the comments of Linus Walleij:
- Add a few comments
- Expand commit log message
- Use the BIT() macro for bit offsets
- Rewrite CPENABLE handling as static inlines
- Use device_initcall()
* Depend on !SMP for reason explained in the comments (Marc Gauthier)
* Use XCHAL_CP_ID_XTIOP to enable/disable GPIO32 only
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Merged the GPIO descriptor API from Alexandre Courbot.
This is a first step toward trying to get rid of the
global GPIO numberspace for the future.
- Add an API so that driver can flag that a certain GPIO
line is being used by a irqchip backend for generating
IRQs, so that we can enforce checks, like not allowing
users to switch that line to an output at runtime, since
this makes no sense. Implemented corresponding calls
in a few select drivers.
- ACPI GPIO cleanups, refactorings and switch to using the
descriptor-based interface.
- Support for the TPS80036 Palmas GPIO variant.
- A new driver for the Broadcom Kona GPIO SoC IP block.
- Device tree support for the PCF857x driver.
- A set of ARM GPIO refactorings with the goal of getting
rid of a bunch of custom GPIO implementations from the
arch/arm/* tree:
- Move the IOP GPIO driver to the GPIO subsystem and
fix all users to use the gpiolib API for accessing
GPIOs. Delete the old custom GPIO implementation.
- Delete the unused custom PXA GPIO implemention.
- Convert all users of the IXP4 custom GPIO
implementation to use gpiolib and delete the custom
implementation.
- Delete the custom Gemini GPIO implementation, also
completely unused.
- Various cleanups and renamings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=881E
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"Here is the bulk of GPIO changes for the v3.13 development cycle.
I've got ACKs for the things that affect other subsystems (or it's my
own subsystem, like pinctrl). Most of that pertain to an attempt from
my side to consolidate and get rid of custom GPIO implementations in
the ARM tree. I will continue doing this.
The main change this time is the new GPIO descriptor API, background
for this can be found in Corbet's summary from this january in LWN:
http://lwn.net/Articles/533632/
Summary:
- Merged the GPIO descriptor API from Alexandre Courbot. This is a
first step toward trying to get rid of the global GPIO numberspace
for the future.
- Add an API so that driver can flag that a certain GPIO line is
being used by a irqchip backend for generating IRQs, so that we can
enforce checks, like not allowing users to switch that line to an
output at runtime, since this makes no sense. Implemented
corresponding calls in a few select drivers.
- ACPI GPIO cleanups, refactorings and switch to using the
descriptor-based interface.
- Support for the TPS80036 Palmas GPIO variant.
- A new driver for the Broadcom Kona GPIO SoC IP block.
- Device tree support for the PCF857x driver.
- A set of ARM GPIO refactorings with the goal of getting rid of a
bunch of custom GPIO implementations from the arch/arm/* tree:
* Move the IOP GPIO driver to the GPIO subsystem and fix all users
to use the gpiolib API for accessing GPIOs. Delete the old
custom GPIO implementation.
* Delete the unused custom PXA GPIO implemention.
* Convert all users of the IXP4 custom GPIO implementation to use
gpiolib and delete the custom implementation.
* Delete the custom Gemini GPIO implementation, also completely
unused.
- Various cleanups and renamings"
* tag 'gpio-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
gpio: gpio-mxs: Remove unneeded dt checks
gpio: pl061: don't depend on CONFIG_ARM
gpio: bcm-kona: add missing .owner to struct gpio_chip
gpiolib: provide a declaration of seq_file in gpio/driver.h
gpiolib: include gpio/consumer.h in of_gpio.h for desc_to_gpio()
gpio: provide stubs for devres gpio functions
gpiolib: devres: add missing headers
gpiolib: make GPIO_DEVRES depend on GPIOLIB
gpiolib: devres: fix devm_gpiod_get_index()
gpiolib / ACPI: document the GPIO descriptor based interface
gpiolib / ACPI: allow passing GPIOF_ACTIVE_LOW for GpioInt resources
gpiolib / ACPI: add ACPI support for gpiod_get_index()
gpiolib / ACPI: convert to gpiod interfaces
gpiolib: add gpiod_get() and gpiod_put() functions
gpiolib: port of_ functions to use gpiod
gpiolib: export descriptor-based GPIO interface
Fixup "MAINTAINERS: GPIO-INTEL-MID: add maintainer"
gpio: bcm281xx: Don't print addresses of GPIO area in probe()
gpio: tegra: use new gpio_lock_as_irq() API
gpio: rcar: Include linux/of.h header
...
The GPIO driver for the Abilis Systems TB10x series of SOCs based on ARC700
CPUs. It supports GPIO control and GPIO interrupt generation. This driver
works in conjunction with the TB10x pinctrl driver.
Signed-off-by: Sascha Leuenberger <sascha.leuenberger@abilis.com>
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio-langwell is a deprecated name. Despite the driver was made
initially for Langwell, it supports now other Intel Mid SoC's.
This patch does no change beside the file renaming with Kconfig/Makefile
update.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the IOP GPIO driver to live with its siblings in the
GPIO subsystem.
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the GPIO driver for the Broadcom bcm281xx family of mobile SoCs.
These GPIO controllers may contain up to 8 banks where each bank
includes 32 pins that can be driven high or low and act as an edge
sensitive interrupt.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
[Added depends on OF_GPIO]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull MIPS updates from Ralf Baechle:
"This has been sitting in -next for a while with no objections and all
MIPS defconfigs except one are building fine; that one platform got
broken by another patch in your tree and I'm going to submit a patch
separately.
- a handful of fixes that didn't make 3.11
- a few bits of Octeon 3 support with more to come for a later
release
- platform enhancements for Octeon, ath79, Lantiq, Netlogic and
Ralink SOCs
- a GPIO driver for the Octeon
- some dusting off of the DECstation code
- the usual dose of cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (65 commits)
MIPS: DMA: Fix BUG due to smp_processor_id() in preemptible code
MIPS: kexec: Fix random crashes while loading crashkernel
MIPS: kdump: Skip walking indirection page for crashkernels
MIPS: DECstation HRT calibration bug fixes
MIPS: Export copy_from_user_page() (needed by lustre)
MIPS: Add driver for the built-in PCI controller of the RT3883 SoC
MIPS: DMA: For BMIPS5000 cores flush region just like non-coherent R10000
MIPS: ralink: Add support for reset-controller API
MIPS: ralink: mt7620: Add cpu-feature-override header
MIPS: ralink: mt7620: Add spi clock definition
MIPS: ralink: mt7620: Add wdt clock definition
MIPS: ralink: mt7620: Improve clock frequency detection
MIPS: ralink: mt7620: This SoC has EHCI and OHCI hosts
MIPS: ralink: mt7620: Add verbose ram info
MIPS: ralink: Probe clocksources from OF
MIPS: ralink: Add support for systick timer found on newer ralink SoC
MIPS: ralink: Add support for periodic timer irq
MIPS: Netlogic: Built-in DTB for XLP2xx SoC boards
MIPS: Netlogic: Add support for USB on XLP2xx
MIPS: Netlogic: XLP2xx update for I2C controller
...
This patch adds support for the GPIOs found on the Fintek super-I/O
chips F71882FG and F71889F.
A super-I/O is a legacy I/O controller embedded on x86 motherboards. It
is used to connect the low-bandwidth devices. Among others functions the
F71882FG/F71889F provides: a parallel port, two serial ports, a keyboard
controller, an hardware monitoring controller and some GPIO pins.
Note that this super-I/Os are embedded on some Atom-based LaCie NASes.
The GPIOs are used to control the LEDs and the hard drive power.
Changes since v3:
- Use request_muxed_region to protect the I/O ports against concurrent
accesses.
Changes since v2:
- Remove useless NULL setters for driver data.
Changes since v1:
- Enhance the commit message by describing what is a Super-I/O.
- Use self-explanatory names for the GPIO register macros.
- Add a comment to explain the platform device and driver registration.
- Fix gpio_get when GPIO is configured in input mode. I only had
the hardware to check this mode recently...
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SOCs in the OCTEON family have 16 (or in some cases 20) on-chip
GPIO pins, this driver handles them all. Configuring the pins as
interrupt sources is handled elsewhere (OCTEON's irq handling code).
Signed-off-by: David Daney <david.daney@cavium.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5633/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add gpio support for the on-board PLD found on some Kontron embedded modules.
Originally-from: Michael Brunner <michael.brunner@kontron.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kevin Strasser <kevin.strasser@linux.intel.com>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a GPIO driver for the low-power Powerdown Controller GPIOs in the
TZ1090 SoC.
The driver is instantiated by device tree and supports interrupts for
the SysWake GPIOs only.
Changes in v4:
- fix typos in DT bindings compatible properties
- reference Documentation/devicetree/bindings/gpio/gpio.txt in
gpio-ranges description in DT bindings
- fix gpio-ranges examples in DT bindings (it must now have 3 cells)
Changes in v3:
- separated from irq-imgpdc and removed arch/metag changes to allow
these patches to go upstream separately via the pinctrl[/gpio] trees
(particularly the pinctrl drivers depend on the new pinconf DT
bindings).
- some s/unsigned/unsigned int/.
- gpio-tz1090*: refer to <dt-bindings/gpio/gpio.h> and
<dt-bindings/interrupt-controller/irq.h> flags in bindings.
- gpio-tz1090*: move initcall from postcore to subsys.
Changes in v2:
- gpio-tz1090-pdc: remove references to Linux flags in dt bindings
- gpio-tz1090-pdc: make use of BIT() from linux/bitops.h
- gpio-tz1090-pdc: make register accessors inline to match pinctrl
- gpio-tz1090-pdc: update gpio-ranges to use 3 cells after recent ABI
breakage
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a GPIO driver for the main GPIOs found in the TZ1090 (Comet) SoC.
This doesn't include low-power GPIOs as they're controlled separately
via the Powerdown Controller (PDC) registers.
The driver is instantiated by device tree and supports interrupts for
all GPIOs.
Changes in v4:
- fix typos in DT bindings compatible properties
- reference Documentation/devicetree/bindings/gpio/gpio.txt in
gpio-ranges description in DT bindings
- fix gpio-ranges examples in DT bindings (it must now have 3 cells)
- gpio-tz1090: use of_property_read_u32 instead of of_get_property
Changes in v3:
- separated from irq-imgpdc and removed arch/metag changes to allow
these patches to go upstream separately via the pinctrl[/gpio] trees
(particularly the pinctrl drivers depend on the new pinconf DT
bindings).
- some s/unsigned/unsigned int/.
- some s/unsigned int/bool/ and use of BIT().
- gpio-tz1090*: refer to <dt-bindings/gpio/gpio.h> and
<dt-bindings/interrupt-controller/irq.h> flags in bindings.
- gpio-tz1090*: move initcall from postcore to subsys.
- gpio-tz1090: add REG_ prefix to some constants for consistency.
- gpio-tz1090: add comment to explain tz1090_gpio_irq_next_edge
cunningness.
Changes in v2:
- gpio-tz1090: remove references to Linux flags in dt bindings
- gpio-tz1090: make use of BIT() from linux/bitops.h
- gpio-tz1090: make register accessors inline to match pinctrl
- gpio-tz1090: update gpio-ranges to use 3 cells after recent ABI
breakage
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds Kconfig entry that selects whether legacy Samsung GPIO
driver should be built or not. For platforms that support only DT based
boot, the new pinctrl driver is used and so the old one is not needed.
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
These patches are all for Renesas shmobile, and depend on the earlier
pinctrl updates. Remarkably, this adds support for three new SoCs:
r8a73a4, r8a73a4 and r8a7778. The bulk of the code added for these is
for pinctrl (using the new subsystem) and for clocks (not yet using the
common clock subsystem). The latter will have to get converted in one
of the upcoming releases, but shmobile is not ready for that yet.
The series also contains Renesas shmobile board changes, adding one
board file for each of the three new SoCs. These boards are using a
mix of classic and device-tree based probing, as there is still a lot of
infrastructure in shmobile that has not been converted to DT yet. Once
those are resolved to the degree that no board specific setup code is
needed, they can get folded into the respective SoC setup files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xaLf
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates (part 2) from Arnd Bergmann:
"These patches are all for Renesas shmobile, and depend on the earlier
pinctrl updates. Remarkably, this adds support for three new SoCs:
r8a73a4, r8a73a4 and r8a7778. The bulk of the code added for these is
for pinctrl (using the new subsystem) and for clocks (not yet using
the common clock subsystem). The latter will have to get converted in
one of the upcoming releases, but shmobile is not ready for that yet.
The series also contains Renesas shmobile board changes, adding one
board file for each of the three new SoCs. These boards are using a
mix of classic and device-tree based probing, as there is still a lot
of infrastructure in shmobile that has not been converted to DT yet.
Once those are resolved to the degree that no board specific setup
code is needed, they can get folded into the respective SoC setup files."
* tag 'soc-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (78 commits)
ARM: shmobile: use r8a7790 timer setup code on Lager
ARM: shmobile: force enable of r8a7790 arch timer
ARM: shmobile: Add second I/O range for r8a7790 PFC
ARM: shmobile: bockw: enable network settings on bootargs
ARM: shmobile: bockw: add SMSC ethernet support
ARM: shmobile: R8A7778: add Ether support
ARM: shmobile: bockw: enable SMSC ethernet on defconfig
ARM: shmobile: r8a7778: add r8a7778_init_irq_extpin()
ARM: shmobile: r8a7778: remove pointless PLATFORM_INFO()
ARM: shmobile: mackerel: clean up MMCIF vs. SDHI1 selection
ARM: shmobile: mackerel: add interrupt names for SDHI0
ARM: shmobile: mackerel: switch SDHI and MMCIF interfaces to slot-gpio
ARM: shmobile: mackerel: remove OCR masks, where regulators are used
ARM: shmobile: mackerel: SDHI resources do not have to be numbered
ARM: shmobile: Initial r8a7790 Lager board support
ARM: shmobile: APE6EVM LAN9220 support
ARM: shmobile: APE6EVM PFC support
ARM: shmobile: APE6EVM base support
ARM: shmobile: kzm9g-reference: add ethernet support
ARM: shmobile: add R-Car M1A Bock-W platform support
...
The usual selection of bug fixes and driver updates for GPIO. Nothing
really stands out except the addition of the GRGPIO driver and some
enhacements to ACPI support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=PwUd
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull GPIO changes from Grant Likely:
"The usual selection of bug fixes and driver updates for GPIO. Nothing
really stands out except the addition of the GRGPIO driver and some
enhacements to ACPI support"
I'm pulling this despite the earlier mess. Let's hope it compiles these
days.
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux: (46 commits)
gpio: grgpio: Add irq support
gpio: grgpio: Add device driver for GRGPIO cores
gpiolib-acpi: introduce acpi_get_gpio_by_index() helper
GPIO: gpio-generic: remove kfree() from bgpio_remove call
gpio / ACPI: Handle ACPI events in accordance with the spec
gpio: lpc32xx: Fix off-by-one valid range checking for bank
gpio: mcp23s08: convert driver to DT
gpio/omap: force restore if context loss is not detectable
gpio/omap: optimise interrupt service routine
gpio/omap: remove extra context restores in *_runtime_resume()
gpio/omap: free irq domain in probe() failure paths
gpio: gpio-generic: Add 16 and 32 bit big endian byte order support
gpio: samsung: Add terminating entry for exynos_pinctrl_ids
gpio: mvebu: add dbg_show function
MAX7301 GPIO: Do not force SPI speed when using OF Platform
gpio: gpio-tps65910.c: fix checkpatch error
gpio: gpio-timberdale.c: fix checkpatch error
gpio: gpio-tc3589x.c: fix checkpatch errors
gpio: gpio-stp-xway.c: fix checkpatch error
gpio: gpio-sch.c: fix checkpatch error
...
This merges in the revert of multiplatform support for exynos.
Trivial conflicts on removed code. Also, needed to add "select COMMON_CLK"
to the non-multiplatform EXYNOS config option.
* samsung/exynos-multiplatform:
Revert "ARM: exynos: enable multiplatform support"
Signed-off-by: Olof Johansson <olof@lixom.net>
This reverts commit bd51de53e1.
Turns out that multiplatform breaks some uses cases, such as when you
have an existing defconfig, since it adds the new EXYNOS_SINGLE config
option as a dependecy. As a result, nearly all exynos config options
will be disabled by default.
Reverting instead of rebasing since this branch is pulled in as a
dependency elsewhere.
Signed-off-by: Olof Johansson <olof@lixom.net>
This driver supports GRGPIO gpio cores available in the GRLIB VHDL IP
core library from Aeroflex Gaisler.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes it possible to enable the exynos platform as part of a
multiplatform kernel, in addition to keeping the single-platform
exynos support.
The multiplatform variant has a number of limitations at the moment:
* It only supports DT-enabled machines. This is not a problem in
the long run, as non-DT machines for exynos are going away.
The main problem here is that the gpio code and the exynos_eint
irqchip are not multiplatform capable but still required for
ATAGS based boot.
* The watchdog driver is still missing a conversion.
* sparsemem and memory_holes are currently not supported in
multiplatform.
The the multiplatform aware ARCH_EXYNOS Kconfig symbol is disabled
for now, as dependent patches are still pending in other
subsystem trees. We will enable it once everything comes together.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
With the move to a combined pinctrl/gpio driver, the arch-vt8500
gpio driver is no longer required.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This patch is V3 of a GPIO driver for the R-Car series of
SoCs from Renesas. This driver is designed to be reusable
between multiple SoCs that share the same basic building block,
but so far it has only been used on R-Car H1 (r8a7779).
Each driver instance handles 32 GPIOs with individually
maskable IRQs. The driver operates on a single I/O memory
range and the 32 GPIOs are hooked up a single interrupt.
In the case of R-Car H1 either external IRQ pins or GPIOs
with interrupts can be used for on-board interupts. For
external IRQs 4 pins are supported, and in the case of GPIO
there are 202 GPIOS as 202 interrupts hooked up via 6 driver
instances and to the GIC and the Cortex-A9 Quad.
At this point this driver is interfacing as a regular
platform device driver. In the future DT support will be
submitted as an incremental feature patch.
Signed-off-by: Magnus Damm <damm@opensource.se>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This branch contains the usual set of individual driver improvements and
bug fixes, as well as updates to the core code. The more notable changes
include:
- Internally add new API for referencing GPIOs by gpio_desc instead of
number. Eventually this will become a public API
- ACPI GPIO binding support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JN4M
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull GPIO changes from Grant Likely:
"This branch contains the usual set of individual driver improvements
and bug fixes, as well as updates to the core code. The more notable
changes include:
- Internally add new API for referencing GPIOs by gpio_desc instead
of number. Eventually this will become a public API
- ACPI GPIO binding support"
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux: (33 commits)
arm64: select ARCH_WANT_OPTIONAL_GPIOLIB
gpio: em: Use irq_domain_add_simple() to fix runtime error
gpio: using common order: let 'static const' instead of 'const static'
gpio/vt8500: memory cleanup missing
gpiolib: Fix locking on gpio debugfs files
gpiolib: let gpio_chip reference its descriptors
gpiolib: use descriptors internally
gpiolib: use gpio_chips list in gpiochip_find_base
gpiolib: use gpio_chips list in sysfs ops
gpiolib: use gpio_chips list in gpiochip_find
gpiolib: use gpio_chips list in gpiolib_sysfs_init
gpiolib: link all gpio_chips using a list
gpio/langwell: cleanup driver
gpio/langwell: Add Cloverview ids to pci device table
gpio/lynxpoint: add chipset gpio driver.
gpiolib: add missing braces in gpio_direction_show
gpiolib-acpi: Fix error checks in interrupt requesting
gpio: mpc8xxx: don't set IRQ_TYPE_NONE when creating irq mapping
gpiolib: remove gpiochip_reserve()
arm: pxa: tosa: do not use gpiochip_reserve()
...
No new drivers this time, but a bunch of fairly big cleanups:
- Roger Quadros worked on a OMAP USBHS and TLL platform data consolidation,
OMAP5 support and clock management code cleanup.
- The first step of a major sync for the ab8500 driver from Lee Jones. In
particular, the debugfs and the sysct interfaces got extended and improved.
- Peter Ujfalusi sent a nice patchset for cleaning and fixing the twl-core
driver, with a much needed module id lookup code improvement.
- The regular wm5102 and arizona cleanups and fixes from Mark Brown.
- Laxman Dewangan extended the palmas APIs in order to implement the palmas
GPIO and rt drivers.
- Laxman also added DT support for the tps65090 driver.
- The Intel SCH and ICH drivers got a couple fixes from Aaron Sierra and
Darren Hart.
- Linus Walleij patchset for the ab8500 driver allowed ab8500 and ab9540 based
devices to switch to the new abx500 pin-ctrl driver.
- The max8925 now has device tree and irqdomain support thanks to Qing Xu.
- The recently added rtsx driver got a few cleanups and fixes for a better
card detection code path and now also supports the RTS5227 chipset, thanks
to Wei Wang and Roger Tseng.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BhC1
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFS updates from Samuel Ortiz:
"This is the MFD pull request for the 3.9 merge window.
No new drivers this time, but a bunch of fairly big cleanups:
- Roger Quadros worked on a OMAP USBHS and TLL platform data
consolidation, OMAP5 support and clock management code cleanup.
- The first step of a major sync for the ab8500 driver from Lee
Jones. In particular, the debugfs and the sysct interfaces got
extended and improved.
- Peter Ujfalusi sent a nice patchset for cleaning and fixing the
twl-core driver, with a much needed module id lookup code
improvement.
- The regular wm5102 and arizona cleanups and fixes from Mark Brown.
- Laxman Dewangan extended the palmas APIs in order to implement the
palmas GPIO and rt drivers.
- Laxman also added DT support for the tps65090 driver.
- The Intel SCH and ICH drivers got a couple fixes from Aaron Sierra
and Darren Hart.
- Linus Walleij patchset for the ab8500 driver allowed ab8500 and
ab9540 based devices to switch to the new abx500 pin-ctrl driver.
- The max8925 now has device tree and irqdomain support thanks to
Qing Xu.
- The recently added rtsx driver got a few cleanups and fixes for a
better card detection code path and now also supports the RTS5227
chipset, thanks to Wei Wang and Roger Tseng."
* tag 'mfd-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (109 commits)
mfd: lpc_ich: Use devres API to allocate private data
mfd: lpc_ich: Add Device IDs for Intel Wellsburg PCH
mfd: lpc_sch: Accomodate partial population of the MFD devices
mfd: da9052-i2c: Staticize da9052_i2c_fix()
mfd: syscon: Fix sparse warning
mfd: twl-core: Fix kernel panic on boot
mfd: rtsx: Fix issue that booting OS with SD card inserted
mfd: ab8500: Fix compile error
mfd: Add missing GENERIC_HARDIRQS dependecies
Documentation: Add docs for max8925 dt
mfd: max8925: Add dts
mfd: max8925: Support dt for backlight
mfd: max8925: Fix onkey driver irq base
mfd: max8925: Fix mfd device register failure
mfd: max8925: Add irqdomain for dt
mfd: vexpress: Allow vexpress-sysreg to self-initialise
mfd: rtsx: Support RTS5227
mfd: rtsx: Implement driving adjustment to device-dependent callbacks
mfd: vexpress: Add pseudo-GPIO based LEDs
mfd: ab8500: Rename ab8500 to abx500 for hwmon driver
...
Add gpio driver for TI Palmas series PMIC. This has 8 gpio which can
work as input/output.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add gpio support for Intel Lynxpoint chipset.
Lynxpoint supports 94 gpio pins which can generate interrupts.
Driver will fail requests for pins that are marked as owned by ACPI, or
set in an alternate mode (non-gpio).
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The AB8500 GPIO driver has been marked BROKEN for ages, and we
have something better in store: a shiny new pinctrl driver. So
let use delete this old driver as the first step.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some architectures (e.g. blackfin) provide gpio API without requiring
GPIOLIB support (ARCH_WANT_OPTIONAL_GPIOLIB). devm_gpio_* functions
should also work for these architectures, since they do not really
depend on GPIOLIB.
Add a new option GPIO_DEVRES (enabled by default) to control the build
of devres.c. It also removes the empty version of devm_gpio_*
functions for !GENERIC_GPIO build from linux/gpio.h, and moves the
function declarations from asm-generic/gpio.h into linux/gpio.h.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have several new drivers, most of the time coming with their sub devices
drivers:
- Austria Microsystem's AS3711
- Nano River's viperboard
- TI's TPS80031, AM335x TS/ADC,
- Realtek's MMC/memstick card reader
- Nokia's retu
We also got some notable cleanups and improvements:
- tps6586x got converted to IRQ domains.
- tps65910 and tps65090 moved to the regmap IRQ API.
- STMPE is now Device Tree aware.
- A general twl6040 and twl-core cleanup, with moves to the regmap I/O and IRQ
APIs and a conversion to the recently added PWM framework.
- sta2x11 gained regmap support.
Then the rest is mostly tiny cleanups and fixes, among which we have Mark's
wm5xxx and wm8xxx patchset.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=F790
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFS update from Samuel Ortiz:
"This is the MFD patch set for the 3.8 merge window.
We have several new drivers, most of the time coming with their sub
devices drivers:
- Austria Microsystem's AS3711
- Nano River's viperboard
- TI's TPS80031, AM335x TS/ADC,
- Realtek's MMC/memstick card reader
- Nokia's retu
We also got some notable cleanups and improvements:
- tps6586x got converted to IRQ domains.
- tps65910 and tps65090 moved to the regmap IRQ API.
- STMPE is now Device Tree aware.
- A general twl6040 and twl-core cleanup, with moves to the regmap
I/O and IRQ APIs and a conversion to the recently added PWM
framework.
- sta2x11 gained regmap support.
Then the rest is mostly tiny cleanups and fixes, among which we have
Mark's wm5xxx and wm8xxx patchset."
Far amount of annoying but largely trivial conflicts. Many due to
__devinit/exit removal, others due to one or two of the new drivers also
having come in through another tree.
* tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (119 commits)
mfd: tps6507x: Convert to devm_kzalloc
mfd: stmpe: Update DT support for stmpe driver
mfd: wm5102: Add readback of DSP status 3 register
mfd: arizona: Log if we fail to create the primary IRQ domain
mfd: tps80031: MFD_TPS80031 needs to select REGMAP_IRQ
mfd: tps80031: Add terminating entry for tps80031_id_table
mfd: sta2x11: Fix potential NULL pointer dereference in __sta2x11_mfd_mask()
mfd: wm5102: Add tuning for revision B
mfd: arizona: Defer patch initialistation until after first device boot
mfd: tps65910: Fix wrong ack_base register
mfd: tps65910: Remove unused data
mfd: stmpe: Get rid of irq_invert_polarity
mfd: ab8500-core: Fix invalid free of devm_ allocated data
mfd: wm5102: Mark DSP memory regions as volatile
mfd: wm5102: Correct default for LDO1_CONTROL_2
mfd: arizona: Register haptics devices
mfd: wm8994: Make current device behaviour the default
mfd: tps65090: MFD_TPS65090 needs to select REGMAP_IRQ
mfd: Fix stmpe.c build when OF is not enabled
mfd: jz4740-adc: Use devm_kzalloc
...
Primarily device driver additions, features and bug fixes. Not much
touching gpio common subsystem support. Should not be scary.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=2XeO
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO updates from Grant Likely:
"GPIO follow up patch and type change for v3.5 merge window
Primarily device driver additions, features and bug fixes. Not much
touching gpio common subsystem support. Should not be scary."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
gpio: Provide the STMPE GPIO driver with its own IRQ Domain
gpio: add TS-5500 DIO blocks support
gpio: pcf857x: use client->irq for gpio_to_irq()
gpio: stmpe: Add DT support for stmpe gpio
gpio: pl061 depends on ARM
gpio/pl061: remove old comment
gpio: SPEAr: add spi chipselect control driver
gpio: gpio-max710x: Support device tree probing
gpio: twl4030: Use only TWL4030_MODULE_LED for LED configuration
gpio: tegra: read output value when gpio is set in direction_out
gpio: pca953x: Add compatible strings to gpio-pca953x driver
gpio: pca953x: Register an IRQ domain
gpio: mvebu: Set free callback for gpio_chip
gpio: tegra: Drop exporting static functions
gpio: tegra: Staticize non-exported symbols
gpio: tegra: fix suspend/resume apis
gpio-pch: Set parent dev for gpio chip
gpio: em: Fix build errors
GPIO: clps711x: use platform_device_unregister in gpio_clps711x_init()
gpio/tc3589x: convert to use the simple irqdomain
...
Technologic Systems TS-5500 provides digital I/O lines exposed through
pin blocks. On this platform, there are three of them, named DIO1, DIO2
and LCD port, that may be used as a DIO block.
The TS-5500 pin blocks are described in the product's wiki:
http://wiki.embeddedarm.com/wiki/TS-5500#Digital_I.2FO
This driver is not limited to the TS-5500 blocks. It can be extended to
support similar boards pin blocks, such as on the TS-5600.
This patch is the V2 of the previous https://lkml.org/lkml/2012/9/25/671
with corrections suggested by Linus Walleij.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jerome Oufella <jerome.oufella@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for translating ACPI GPIO pin numbers to Linux GPIO API pins.
Needs a gpio controller driver with the acpi handler hook set.
Drivers can use acpi_get_gpio() to translate ACPI5 GpioIO and GpioInt
resources to Linux GPIO's.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This adds the mfd cell to use the gpio a and gpio b part
of the Nano River Technologies viperboard.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
SPEAr platform provides a provision to control chipselects of ARM PL022
Prime Cell spi controller through its system registers, which otherwise
remains under PL022 control which some protocols do not want.
This commit intends to provide the spi chipselect control in software over
gpiolib interface. spi chip drivers can use the exported gpiolib interface to
define their chipselect through DT or platform data.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The CLPS711X CPUs provide some GPIOs for use in the system. This
driver provides support for these via gpiolib. Due to platform
limitations, driver does not support interrupts, only inputs and
outputs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>