When reading or writing crypto buffers the inner loops can
be replaced with readsl and writesl which will on ARM result
in a tight assembly loop, speeding up encryption/decryption
a little bit. This optimization was in the Ux500 driver so
let's carry it over to the STM32 driver.
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Lionel Debieve <lionel.debieve@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This adds a few small quirks to handle the differences between
the STM32 and Ux500 cryp blocks. The following differences
are handled with special bool switch bits in the capabilities:
- The main difference is that some registers are removed, so we
add register offsets for all registers in the
per-variant data. Then we assign the right offsets for Ux500
vs the STM32 variants.
- The Ux500 does not support the aeads algorithms; gcm(aes)
and ccm(aes). Avoid registering them when running on Ux500.
- The Ux500 has a special "linear" key format and does some
elaborare bit swizzling of the key bits before writing them
into the key registers. This is written as an "application
note" inside the DB8500 design specification, and seems to
be the result of some mishap when assigning the data lines
to register bits. (STM32 has clearly fixed this.)
- The Ux500 does not have the KP "key prepare" bit in the
CR register. Instead, we need to set the KSE bit,
"key schedule encryption" bit which does the same thing
but is in bit 11 rather than being a special "algorithm
type" as on STM32. The algorithm must however be specified
as AES ECB while doing this.
- The Ux500 cannot just read out IV registers, we need to
set the KEYRDEN "key read enable" bit, as this protects
not just the key but also the IV from being read out.
Enable this bit before reading out the IV and disable it
afterwards.
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked by: Lionel Debieve <lionel.debieve@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There are a couple of spelling mistakes in dev_err messages. Fix them.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: nicolas.toromanoff@foss.st.com
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We should not call pm_runtime_resume_and_get where the reference
count is expected to be incremented unconditionally. This patch
reverts these calls to the original unconditional get_sync call.
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: 747bf30fd9 ("crypto: stm32/cryp - Fix PM reference leak...")
Fixes: 1cb3ad7019 ("crypto: stm32/hash - Fix PM reference leak...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The CRYP IP checks the written key depending of the configuration, it's
safer to write the whole configuration to hardware then the key to avoid
unexpected key rejection.
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Extra crypto manager auto test were crashing or failling due
to 2 reasons:
- block in a dead loop (dues to issues in cipher end process management)
- crash due to read/write unmapped memory (this crash was also reported
when using openssl afalg engine)
Rework interrupt management, interrupts are masked as soon as they are
no more used: if input buffer is fully consumed, "Input FIFO not full"
interrupt is masked and if output buffer is full, "Output FIFO not
empty" interrupt is masked.
And crypto request finish when input *and* outpout buffer are fully
read/write.
About the crash due to unmapped memory, using scatterwalk_copychunks()
that will map and copy each block fix the issue.
Using this api and copying full block will also fix unaligned data
access, avoid early copy of in/out buffer, and make useless the extra
alignment constraint.
Fixes: 9e054ec21e ("crypto: stm32 - Support for STM32 CRYP crypto module")
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This fixes the lrw autotest if lrw uses the CRYP as the AES block cipher
provider (as ecb(aes)). At end of request, CRYP should not update the IV
in case of ECB chaining mode. Indeed the ECB chaining mode never uses
the IV, but the software LRW chaining mode uses the IV field as
a counter and due to the (unexpected) update done by CRYP while the AES
block process, the counter get a wrong value when the IV overflow.
Fixes: 5f49f18d27 ("crypto: stm32/cryp - update to return iv_out")
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Some auto tests failed because driver wasn't returning the expected
error with some input size/iv value/tag size.
Now:
Return 0 early for empty buffer. (We don't need to start the engine for
an empty input buffer).
Accept any valid authsize for gcm(aes).
Return -EINVAL if iv for ccm(aes) is invalid.
Return -EINVAL if buffer size is a not a multiple of algorithm block size.
Fixes: 9e054ec21e ("crypto: stm32 - Support for STM32 CRYP crypto module")
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Don't erase key:
If key is erased before the crypto_finalize_.*_request() call, some
pending process will run with a key={ 0 }.
Moreover if the key is reset at end of request, it breaks xts chaining
mode, as for last xts block (in case input len is not a multiple of
block) a new AES request is started without calling again set_key().
Fixes: 9e054ec21e ("crypto: stm32 - Support for STM32 CRYP crypto module")
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
STM32 CRYP hardware doesn't manage CTR counter bigger than max U32, as
a workaround, at each block the current IV is saved, if the saved IV
lower u32 is 0xFFFFFFFF, the full IV is manually incremented, and set
in hardware.
Fixes: bbb2832620 ("crypto: stm32 - Fix sparse warnings")
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Change driver to not print an error message when the device
probe is deferred for a clock resource.
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Change stm32 CRYP driver to defer its probe operation when
reset controller device is registered but has not been probed yet.
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Signed-off-by: Shixin Liu <liushixin2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch changes the cast in stm32_cryp_check_ctr_counter from
u32 to __be32 to match the prototype of stm32_cryp_hw_write_iv
correctly.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch fixes most of the sparse endianness warnings in stm32.
The patch itself doesn't change anything apart from markings,
but there is some questionable code in stm32_cryp_check_ctr_counter.
That function operates on the counters as if they're in CPU order,
however, they're then written out as big-endian. This looks like
a genuine bug. Therefore I've left that warning alone until
someone can confirm that this really does work as intended on
little-endian.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit 7a7ffe65c8 ("crypto: skcipher - Add top-level skcipher interface")
dated 20 august 2015 introduced the new skcipher API which is supposed to
replace both blkcipher and ablkcipher. While all consumers of the API have
been converted long ago, some producers of the ablkcipher remain, forcing
us to keep the ablkcipher support routines alive, along with the matching
code to expose [a]blkciphers via the skcipher API.
So switch this driver to the skcipher API, allowing us to finally drop the
ablkcipher code in the near future.
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: <linux-crypto@vger.kernel.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Based on 1 normalized pattern(s):
license terms gnu general public license gpl version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.447718015@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel crypto API request output the next IV data to
IV buffer for CBC implementation.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Mutex is badly used between threaded irq and driver.
This mutex must be removed as the framework must ensure
that requests must be serialized to avoid issue. Rework
req to avoid crash during finalize by fixing the NULL
pointer issue.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add weak key test for des functions calling the generic
des_ekey.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch forbids the use of 2-key 3DES (K1 == K3) in FIPS mode.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Lionel Debieve<lionel.debieve@st.com>
Tested-by: Lionel Debieve<lionel.debieve@st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Adding pm and pm_runtime support to STM32 CRYP.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
stm32mp1 differs from stm32f7 in the way it handles byte ordering and
padding for aes gcm & ccm algo.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch convert the stm32-cryp driver to the new crypto engine API.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch fix the following build failure:
CC [M] drivers/crypto/stm32/stm32-cryp.o
In file included from drivers/crypto/stm32/stm32-cryp.c:11:0:
drivers/crypto/stm32/stm32-cryp.c:1049:25: error: 'sti_dt_ids' undeclared here (not in a function)
MODULE_DEVICE_TABLE(of, sti_dt_ids);
Let's replace sti_dt_ids with stm32_dt_ids which is just declared
before.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This module registers block cipher algorithms that make use of the
STMicroelectronics STM32 crypto "CRYP1" hardware.
The following algorithms are supported:
- aes: ecb, cbc, ctr
- des: ecb, cbc
- tdes: ecb, cbc
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Linus Walleij