Currently the usbnet core does not update the tx_packets statistic for
drivers with FLAG_MULTI_PACKET and there is no hook in the TX
completion path where they could do this.
cdc_ncm and dependent drivers are bumping tx_packets stat on the
transmit path while asix and sr9800 aren't updating it at all.
Add a packet count in struct skb_data so these drivers can fill it
in, initialise it to 1 for other drivers, and add the packet count
to the tx_packets statistic on completion.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes below warning by dynamically allocating memory
All warnings:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c: In function
'cctrl_tbl_show':
>> drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c:689:1: warning: the
>> frame
>> size of 1028 bytes is larger than 1024 bytes [-Wframe-larger-than=]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ucc_geth was indicating link up after a port is administratively enabled even
when nothing is plugged in. This causes user-space tools to see a spurious link
up the first time after boot.
Signed-off-by: Cliff Clark <cliff_clark@selinc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We occasionally see in procedure mlx4_GEN_EQE that the driver tries
to grab an uninitialized mutex.
This can occur in only one of two ways:
1. We are trying to generate an async event on an uninitialized slave.
2. We are trying to generate an async event on an illegal slave number
( < 0 or > persist->num_vfs) or an inactive slave.
To deal with #1: move the mutex initialization from specific slave init
sequence in procedure mlx_master_do_cmd to mlx4_multi_func_init() (so that
the mutex is always initialized for all slaves).
To deal with #2: check in procedure mlx4_GEN_EQE that the slave number
provided is in the proper range and that the slave is active.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netdevice registration should be performed a the end of the driver
initialization flow. If we don't do that, after calling register_netdevice,
device callbacks may be issued by higher layers of the stack before
final configuration of the device is done.
For example (VXLAN configuration race), mlx4_SET_PORT_VXLAN was issued
after the register_netdev command. System network scripts may configure
the interface (UP) right after the registration, which also attach
unicast VXLAN steering rule, before mlx4_SET_PORT_VXLAN was called,
causing the firmware to fail the rule attachment.
Fixes: 837052d0cc ("net/mlx4_en: Add netdev support for TCP/IP offloads of vxlan tunneling")
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* avoid panic with lots of IBSS stations
* Fix dvm's behavior after suspend resume
* Allow to keep connection after CSA failure
* Remove a noisy by harmless WARN_ON
* New device IDs
rtlwifi:
* fix IOMMU mapping leak in AP mode
brcmfmac:
* disable MBSS feature for BCM43362 to get AP mode working again
ath9k:
* disable Transmit Power Control (TPC) again due to regressions
* fix beaconing issue with AP+STA setup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVEQL4AAoJEG4XJFUm622boBwH/R61GyJvh2OieOfv35fv84N0
h4abht9N4gfogwJcF9AT0rPddo+ueYhD1pSYOS6pyM1d2OjhJq73vEVetCUKpX46
TpFw2hZOOZKj97flYyi7dPXQxGcUYLAzfqZ5Dn45czGuwMk/v3v+Ni3lzHUfmKvm
jrjHWKm2+WiJGRO7xJEmUAZoXTLEZdQtxLC3oViIeldhjsS5XQfx6K7mlp6L/7lC
zvHBSkLFEjjn6fMa17r9GgCsN7HkHuK8/tbXfbDyVw37bWte/6ZJv+1IUn6HPUKJ
mCRl5Sbs/+Rg0sqWaf1ygjGCghx9I7U4R9EvaZxpSnn+KjeeL4ibds2Lq+DoAaM=
=fEF3
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2015-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
iwlwifi:
* avoid panic with lots of IBSS stations
* Fix dvm's behavior after suspend resume
* Allow to keep connection after CSA failure
* Remove a noisy by harmless WARN_ON
* New device IDs
rtlwifi:
* fix IOMMU mapping leak in AP mode
brcmfmac:
* disable MBSS feature for BCM43362 to get AP mode working again
ath9k:
* disable Transmit Power Control (TPC) again due to regressions
* fix beaconing issue with AP+STA setup
Signed-off-by: David S. Miller <davem@davemloft.net>
Master change notifications may occur other than when joining or
leaving a bridge, for example when being added to or removed from
a bond or Open vSwitch.
Previously in those cases rocker_port_bridge_leave() was called
which results in a null-pointer dereference as rocker_port->bridge_dev
is NULL because there is no bridge device.
This patch makes provision for doing nothing in such cases.
Fixes: 6c70794500 ("rocker: implement L2 bridge offloading")
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Statistics' state-machine in bnx2x driver must be synced with various driver
flows, but its current locking scheme manages to be wasteful [using 2 locks +
additional local variable] and prone to race-conditions at the same time,
as the state-machine and 'action' are being accessed under different locks.
In addition, current 'safe exec' isn't in fact safe, since the only guarantee
it gives is that DMA transactions are over, but ramrods might still be running.
This patch cleans up said logic, leaving us with a single lock for the entire
flow and removing the possible races.
Changes from v2:
- Switched into mutex locking from semaphore locking.
- Release locks on error flows.
Changes from v1:
Failure to acquire lock fails flow instead of printing a warning and
allowing access to the critical section.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return EPROBE_DEFER if Regulator returns EPROBE_DEFER
If the Flexcan driver is built into kernel and a regulator is used to
enable the CAN transceiver, the Flexcan driver may not use the regulator.
When initializing the Flexcan device with a regulator defined in the device
tree, but not initialized, the regulator subsystem returns EPROBE_DEFER, hence
the Flexcan init fails.
The solution for this is to return EPROBE_DEFER if regulator is not initialized
and wait until the regulator is initialized.
Signed-off-by: Andreas Werner <kernel@andy89.org>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Making sure that the bus-off state gets passed to can_change_state().
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The PCAN USB (pro) FD adapters with firmware versions > 2.x support the
switching between ISO (default) and non-ISO conform bitstreams on the CAN bus.
The setting for the 2.x firmware adapters can be modified with the 'ip' tool
from the iproute2 package (option: fd-non-iso [on|off]).
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The PUCAN_CMD_RX_FRAME_(ENABLE|DISABLE) command has extended its purpose
and was therefore renamed to PUCAN_CMD_SET_(EN|DIS)_OPTION.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
smatch detected the following issue:
drivers/net/can/usb/gs_usb.c:904 gs_usb_probe() error:
potential null dereference 'dev'. (kzalloc returns null)
Add a check for null return from kzalloc and return -ENOMEM
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
USB endpoint's wMaxPacketSize field is an le16 entity. Use
appropriate le16_to_cpu macros to maintain endian independence.
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Current driver code arbitrarily assumes a max outstanding tx
value of 16 parallel transmissions. Meanwhile, the device
firmware provides its actual maximum inside its reply to the
CMD_GET_SOFTWARE_INFO message.
Under heavy tx traffic, if the interleaved transmissions count
increases above the limit reported by firmware, the firmware
breaks up badly, reports a massive list of internal errors, and
the candump traces hardly matches the actual frames sent and
received.
On the other hand, in certain models, the firmware can support
up to 48 tx URBs instead of just 16, increasing the driver
throughput by two-fold and reducing the possibility of -ENOBUFs.
Thus dynamically set the driver's max tx URBs value according
to firmware replies.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Transmission of an AP beacon does not call the TX interrupt service routine,
which usually does the cleanup. Instead, cleanup is handled in a tasklet
completion routine. Unfortunately, this routine has a serious bug in that it does
not release the DMA mapping before it frees the skb, thus one IOMMU mapping is
leaked for each beacon. The test system failed with no free IOMMU mapping slots
approximately one hour after hostapd was used to start an AP.
This issue was reported and tested at https://github.com/lwfinger/rtlwifi_new/issues/30.
Reported-and-tested-by: Kevin Mullican <kevin@mullican.com>
Cc: Kevin Mullican <kevin@mullican.com>
Signed-off-by: Shao Fu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.18+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the device is powered up, some (older) firmware versions fail to work
properly if we send commands before the boot is complete (everything is OK
when the device is hot-plugged). The firmware indicates its ready status by
putting the link up.
Newer firmwares delay the first command so they don't suffer from this problem.
They also report the link being always up.
Wait for firmware to become ready (link up) before sending any commands and/or
data.
This also allows lowering CMD_TIMEOUT value to a reasonable time.
Tested with 4.1.0.9 (old) and 4.1.0.30 (new) firmware versions.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM43362 firmware falsely reports it is capable of providing
MBSS. As a result AP mode no longer works for this device. Therefor
disable MBSS in the driver for this chipset.
Cc: stable@vger.kernel.org # 3.19.y
Reported-by: Jorg Krause <jkrause@posteo.de>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When an EEH error occurs, the device/slot is disconnected. This condition
is more reliably detected (i.e., returns all ones) with an MMIO read rather
than a config read -- especially on power platforms.
Hence, this patch fixes EEH error detection by replacing config reads with
MMIO reads for reading the error registers. The error registers in
Skyhawk-R/BE2/BE3 are accessible both via the config space and the
PCICFG (BAR0) memory space.
Reported-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issuing this cmd for more than 8 EQs does not have the intended effect
even on BEx and Skyhawk-R.
This patch fixes this by issuing this cmd for upto 8 EQs at a time.
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a PF does not restrict its VF interface from enabling vlan
promiscuous mode. This breaks vlan isolation when a vlan
(transparent tagging) is configured on a VF.
This patch fixes this problem by disabling the vlan promisc capability
for VFs.
Reported-by: Yoann Juet <veilletechno-irts@univ-nantes.fr>
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a MIPS Malta board, tons of fifo underflow errors have been observed
when using u-boot as bootloader instead of YAMON. The reason for that
is that YAMON used to set the pcnet device to SRAM mode but u-boot does
not. As a result, the default Tx threshold (64 bytes) is now too small to
keep the fifo relatively used and it can result to Tx fifo underflow errors.
As a result of which, it's best to setup the SRAM on supported controllers
so we can always use the NOUFLO bit.
Cc: <netdev@vger.kernel.org>
Cc: <stable@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: Don Fry <pcnet32@frontier.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware frequently manages to trigger this, and there's
no known driver workaround, so stop warning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the driver callback returns that it's out of space for new
stations, the mac80211 IBSS code still keeps the station so it
doesn't try to add it over and over again.
Since the rate scaling algorithm is separate in mac80211, it also
invokes the rate scaling algorithm for such stations. It doesn't
know that our rate scaling algorithm is tightly integrated with
the MVM code and relies on those data structures, and it cannot
as the abstraction doesn't allow for it.
This leads to crashes when the rate scaling algorithm tries to
use uninitialized data, notably the mvmsta->vif pointer.
Protect against this in the rate scaling algorithm. We cannot get
good rates with such peers anyway since the firmware cannot do
anything with them.
This should fix https://bugzilla.kernel.org/show_bug.cgi?id=93461
CC: <stable@vger.kernel.org>
Reported-by: Richard Taylor <rjt-kernel@thegrindstone.me.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The assumption before this patch was that we don't need to
run again the INIT firmware after the system booted. The
INIT firmware runs calibrations which impact the physical
layer's behavior.
Users reported that it may be helpful to run these
calibrations again every time the interface is brought up.
The penatly is minimal, since the calibrations run fast.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=94341
CC: <stable@vger.kernel.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This reverts commit 11ad714b98 because
it breaks cx82310_eth.
The custom USB_DEVICE_CLASS macro matches
bDeviceClass, bDeviceSubClass and bDeviceProtocol
but the common USB_DEVICE_AND_INTERFACE_INFO matches
bInterfaceClass, bInterfaceSubClass and bInterfaceProtocol instead, which are
not specified.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port statistics bitmap will now be initialized at port init. Even before
starting the port, statistics are visible to the user and must be properly masked.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NUM_PORT_STATS was 9 instead of 10, which caused off-by-one bug when
displaying the statistics starting from tx_chksum_offload in ethtool.
Fixes: f8c6455bb0 ('net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit breaks the legacy platforms, ie. these not using device-tree,
and setting up the interrupt resources with a flag to activate edge
detection. The issue was found on the zylonite platform.
The reason is that zylonite uses platform resources to pass the interrupt number
and the irq flags (here IORESOURCE_IRQ_HIGHEDGE). It expects the driver to
request the irq with these flags, which in turn setups the irq as high edge
triggered.
After the patch, this was supposed to be taken care of with :
irq_resflags = irqd_get_trigger_type(irq_get_irq_data(ndev->irq));
But irq_resflags is 0 for legacy platforms, while for example in
arch/arm/mach-pxa/zylonite.c, in struct resource smc91x_resources[] the
irq flag is specified. This breaks zylonite because the interrupt is not
setup as triggered, and hardware doesn't provide interrupts.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
E1x chips (57710, 57711(E)) have no support for encapsulation
offload. bnx2x incorrectly advertises the support as available.
Setting of those features is conditional on "!CHIP_IS_E1x(bp)", but
the bp struct is not initialized yet at this point and consequently
any chip passes the check.
The check must use the "chip_is_e1x" local variable instead to work
correctly.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TPC support has been observed to cause some tx power fluctuations on
some devices with at least AR934x and AR938x chips.
Disable it for now until the bugs have been found and fixed
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sc->nbcnvifs tracks assigned beacon slots, not enabled beacons.
Therefore, it cannot be used to decide if cur_conf->enable_beacon (bool)
should be updated, or if beacons have been enabled already.
With the current code (depending on the order of calls), beacons often
do not get enabled in an AP+STA setup.
To fix tracking of enabled beacons, convert cur_conf->enable_beacon to a
bitmask of enabled beacon slots.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A number of tx queue wake-up events went missing due to the
outlined scenario below. Start state is a pool of 16 tx URBs,
active tx_urbs count = 15, with the netdev tx queue open.
CPU #1 [softirq] CPU #2 [softirq]
start_xmit() tx_acknowledge()
................ ................
atomic_inc(&tx_urbs);
if (atomic_read(&tx_urbs) >= 16) {
-->
atomic_dec(&tx_urbs);
netif_wake_queue();
return;
<--
netif_stop_queue();
}
At the end, the correct state expected is a 15 tx_urbs count
value with the tx queue state _open_. Due to the race, we get
the same tx_urbs value but with the tx queue state _stopped_.
The wake-up event is completely lost.
Thus avoid hand-rolled concurrency mechanisms and use a proper
lock for contexts and tx queue protection.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Enable the xilinx driver for ARM64.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This reverts commit 2b995f6398.
Панов Андрей reported the following regression:
"Commit 2b995f6398 in 4.0.0-rc3 introduces a
nasty bug in transmit, corrupting packets.
To reproduce:
$ dd if=/dev/zero of=zeros bs=1M count=20
$ md5sum -b zeros
8f4e33f3dc3e414ff94e5fb6905cba8c *zeros
This checksum is correct.
Copy file "zeros" to another host with NFS, and it gets corrupted, checksum is
changed.
File should be big, small amounts of transmit isn't affected.
I use an i.MX6 Quad board.
If this commit is reverted, all works fine."
Reported-by: Панов Андрей <rockford@yandex.ru>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit dfd8645ea1 wrongly assumes that VXLAN_VDI_MASK includes
eight lower order reserved bits of VNI field that are using for remote
checksum offload.
Right now, when VNI number greater then 0xffff, vxlan_udp_encap_recv()
will always return with 'bad_flag' error, reducing the usable vni range
from 0..16777215 to 0..65535. Also, it doesn't really check whether RCO
bits processed or not.
Fix it by adding new VNI mask which has all 32 bits of VNI field:
24 bits for id and 8 bits for other usage.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Array index 'j' is used before limits check.
Suggest put limit check before index use.
Signed-off-by : <Ameenali023@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't delete napi from hash list during module exit. This will
cause the following panic when doing module load and unload:
BUG: unable to handle kernel paging request at 0000004e00000075
IP: [<ffffffff816bd01b>] napi_hash_add+0x6b/0xf0
PGD 3c5d5067 PUD 0
Oops: 0000 [#1] SMP
...
Call Trace:
[<ffffffffa0a5bfb7>] init_vqs+0x107/0x490 [virtio_net]
[<ffffffffa0a5c9f2>] virtnet_probe+0x562/0x791815639d880be [virtio_net]
[<ffffffff8139e667>] virtio_dev_probe+0x137/0x200
[<ffffffff814c7f2a>] driver_probe_device+0x7a/0x250
[<ffffffff814c81d3>] __driver_attach+0x93/0xa0
[<ffffffff814c8140>] ? __device_attach+0x40/0x40
[<ffffffff814c6053>] bus_for_each_dev+0x63/0xa0
[<ffffffff814c7a79>] driver_attach+0x19/0x20
[<ffffffff814c76f0>] bus_add_driver+0x170/0x220
[<ffffffffa0a60000>] ? 0xffffffffa0a60000
[<ffffffff814c894f>] driver_register+0x5f/0xf0
[<ffffffff8139e41b>] register_virtio_driver+0x1b/0x30
[<ffffffffa0a60010>] virtio_net_driver_init+0x10/0x12 [virtio_net]
This patch fixes this by doing this in virtnet_free_queues(). And also
don't delete napi in virtnet_freeze() since it will call
virtnet_free_queues() which has already did this.
Fixes 91815639d8 ("virtio-net: rx busy polling support")
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If this situation ever happens, the mac80211 state machine gets
confused because it never clears csa_active. There was a separate
bug that lead to this happening with a working connection, but it
isn't very robust to try to keep the connection up in this case.
When removing the time event the CSA essentially procedure stops,
so the safest thing to do is to disconnect in this case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
mac80211 now informs the driver when to drop the packets
upon flush(). This will happen before disconnecting, or
before we shut down the interface. We can now rely on this
to drop all the packets including the VO queues.
When mac80211 sets drop to false, wait for all the queues
to be empty.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This fixes a performance regression introduced by
7fbb9d8415 (xen-netback: release pending
index before pushing Tx responses)
Moving the notify outside of the spin locks means it can be delayed a
long time (if the dealloc thread is descheduled or there is an
interrupt or softirq).
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Zoltan Kiss <zoltan.kiss@linaro.org>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix ROC removal - avoids a firmware crash
* fix throughput regression on iwldvm devices
* fix panic in BT Coex
* fixes in rate control
* fixes in scan
b43:
* fix support for 5 GHz only BCM43228 model
rtlwifi:
* improve handling of IPv6 packets
brcmfmac:
* perform bound checking on vendor command buffer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJU/vcnAAoJEG4XJFUm622bBbMIAJAmmITit1LFbm5L5zguIkVq
b9ppfEkgz6JYb4KMe6jWnvrc9yM3ywslH2Evo09ChA53A2sUhORKxlolreGTZxtQ
je3twmUCyzkbvss+aKFS4BzEDDOGwW9A/wk3LT4TZJ7Jp626k1wPXN5WZHaDh0YC
pE7fH6jnNg2Qoe68tG8WmTqrYlzU6mLpI0NNxsW+h2tK2Gqm7jSoMy96RPiwS0ZV
BFnxrJJZViMyPit48pZf338pdndkxOIlDBIJCY8qUwQIt4HxQ8DnmsLWqg9xjnfT
mSO9xgSJxfR02ZDIBYqaK41KlcharjwrF5lDi+JHkoHB2SQQM9A/noxpWu4/JGI=
=pOSK
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2015-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
iwlwifi:
* fix ROC removal - avoids a firmware crash
* fix throughput regression on iwldvm devices
* fix panic in BT Coex
* fixes in rate control
* fixes in scan
b43:
* fix support for 5 GHz only BCM43228 model
rtlwifi:
* improve handling of IPv6 packets
brcmfmac:
* perform bound checking on vendor command buffer
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver support receive VLAN CTAG HW acceleration feature
(NETIF_F_HW_VLAN_CTAG_RX) through software simulation. There calls the
api .skb_copy_to_linear_data_offset() to skip the VLAN tag, but there
have overlap between the two memory data point range. The patch just fix
the issue.
V2:
Michael Grzeschik suggest to use memmove() instead of skb_copy_to_linear_data_offset().
Reported-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Fixes: 1b7bde6d65 ("net: fec: implement rx_copybreak to improve rx performance")
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt is enabled before napi_complete(). A network timeout
occurs if the interrupt handler is called before napi_complete().
Fix the bug by enabling the interrupt after napi_complete().
Signed-off-by: Yongbae Park <yongbae2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt is enabled before napi_complete(). A network timeout
occurs if the interrupt handler is called before napi_complete().
Fix the bug by enabling the interrupt after napi_complete().
Signed-off-by: Yongbae Park <yongbae2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The configurations are not modified by the driver. Make them 'const' so
that they may be placed in a read-only section.
Signed-off-by: Josh Cartwright <joshc@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Kvaser firmware can only read and write messages that are
not crossing the USB endpoint's wMaxPacketSize boundary. While
receiving commands from the CAN device, if the next command in
the same URB buffer crossed that max packet size boundary, the
firmware puts a zero-length placeholder command in its place
then moves the real command to the next boundary mark.
The driver did not recognize such behavior, leading to missing
a good number of rx events during a heavy rx load session.
Moreover, a tx URB context only gets freed upon receiving its
respective tx ACK event. Over time, the free tx URB contexts
pool gets depleted due to the missing ACK events. Consequently,
the netif transmission queue gets __permanently__ stopped; no
frames could be sent again except after restarting the CAN
newtwork interface.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Ben Hutchings