Add an inv_llc_pol field to platform data to control the clock polarity.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
And set input routing when initializing the device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This allows replacing duplicate code blocks by loops over the arrays.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace the dummy video format operations by pad format operations that
configure the output format.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The ADV7604 has sink pads for its HDMI and analog inputs. Report them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds support for the Analog Devices ADV7611 HDMI receiver.
The adv7611 is quite similar to the adv7604. It has only one instead of four
HDMI inputs and no analog frontend though. Also some register bits have been
shuffled around, but large parts of their register maps are compatible.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The file is using u8 which is defined in linux/types.h.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
May also be wrong if the receiver is connected to more than one connector.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The driver strength is board dependent, so set it from the platform_data.
Signed-off-by: Mikhail Khelik <mkhelik@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The adv7604 supports four digital input ports. This patch adds support
for all of them, instead of just port A.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Changes the way the primary mode is handled:
- Remove it from platform_data since it doesn't belong there.
- Add a new mode enum for use with s_routing.
- Collapse the two HDMI modes into one HDMI mode: when setting up the
timings manually we do not need to select HDMI_COMP mode. That's only
needed when selecting a preset.
This patch prepares for the next step where we switch to using the presets
where available.
Signed-off-by: Mats Randgaard <mats.randgaard@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initial version of this driver.
The full datasheets are available from the Analog Devices website:
http://ez.analog.com/docs/DOC-1545
Not all features of the receiver are supported by this driver for various
reasons. Most notably:
- No CEC support (the CEC API needs a lot more discussion)
- Only port A of the four HDMI input ports is implemented (our hardware only
uses that port)
- No HDCP repeater support (we don't use that either)
And since there are some 600-odd pages of datasheet for this single device,
I'm sure that there are many more things missing, but this driver does work
well for our hardware.
Note that I am using the register addresses instead of register names: the
datasheet containing the register descriptions is organized by register
address. Using names would make the datasheet lookup very hard. An attempt
was made to try and document what is being done when registers are used
instead.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Laurent Pinchart