Currently, if plchan->phychan is true, we return immediately from
prep_phy_chan(). We must configure txd->ccfg and increment phychan_hold before
returning. Otherwise, request line number wouldn't be configured in this txd.
Reported-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This patch converts the drivers in drivers/dma/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Piotr Ziecik <kosmo@semihalf.com>
Cc: Rongjun Ying <rongjun.ying@csr.com>
Cc: Barry Song <21cnbao@gmail.com>
Cc: Pelagicore AB <info@pelagicore.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
When we use the SDMA in the UART driver(such as imx6q), we will
meet one situation:
Assume we set 64 bytes for the RX DMA buffer.
The RX DMA buffer has received some data, but not full.
An Aging DMA request will be received by the SDMA controller if we enable the
IDDMAEN(UCR4[6]) in this case.
So the UART driver needs to know the count of the real received bytes,
and push them to upper layer.
Add two new fields to sdmac, and update the `residue` in sdma_tx_status().
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Setting the flags in case of IDE didn't have any effect since the control
register is overwritten few lines below. So move these to be after the control
register is initialized.
Signed-off-by: Rafal Prylowski <prylowski@metasoft.pl>
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Using a configuration structure simplify the finding of SoC
dependent parameters. Both platform data and device tree ids are
using these structures.
This will separate data from code and remove the need for an enum.
Idea from Grant Likely.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Trivial form modification to unify structure look.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This patch provides an option of having the lcla (link address)
in ESRAM instead of allocating it. The bool value (use_esram_lcla)
in the stedma40_platform_data if set to true, then the lcla
address would be taken from platform resources. Also, the
corresponding esram regulator is managed in the
suspend/resume functions.
Signed-off-by: Narayanan G <narayanan.gopalakrishnan@stericsson.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Sparse warns:
drivers/dma/timb_dma.c:168:17: warning: mixing different enum types
drivers/dma/timb_dma.c:168:17: int enum dma_transfer_direction versus
drivers/dma/timb_dma.c:168:17: int enum dma_data_direction
drivers/dma/timb_dma.c:172:32: warning: mixing different enum types
drivers/dma/timb_dma.c:172:32: int enum dma_transfer_direction versus
drivers/dma/timb_dma.c:172:32: int enum dma_data_direction
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
In S2R all DMA registers are reset by hardware and thus they are required to be
reprogrammed. The channels which aren't reprogrammed are channel configuration
and interrupt enable registers, which are currently programmed at chan_alloc
time.
This patch creates another routine to initialize a channel. It will try to
initialize channel on every dwc_dostart() call. If channel is already
initialised then it simply returns, otherwise it configures registers.
This routine will also initialize registers on wakeup from S2R, as we mark
channels as uninitialized on suspend.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Commit 981ed70d8e (dmatest: make dmatest threads freezable) made
dmatest kthread use set_freezable_with_signal(); however, the
interface is scheduled to be removed in the next merge window.
The problem is that unlike userland tasks there's no default place
which handles signal pending state and it isn't clear who owns and/or
is responsible for clearing TIF_SIGPENDING. For example, in the
current code, try_to_freeze() clears TIF_SIGPENDING but it isn't sure
whether it actually owns the TIF_SIGPENDING nor is it race-free -
ie. the task may continue to run with TIF_SIGPENDING set after the
freezable section.
Unfortunately, we don't have wait_for_completion_freezable_timeout().
This patch open codes it and uses wait_event_freezable_timeout()
instead and removes timeout reloading - wait_event_freezable_timeout()
won't return across freezing events (currently racy but fix scheduled)
and timer doesn't decrement while the task is in freezer. Although
this does lose timer-reset-over-freezing, given that timeout is
supposed to be long enough and failure to finish inside is considered
irrecoverable, I don't think this is worth the complexity.
While at it, move completion to outer scope and explain that we're
ignoring dangling pointer problem after timeout. This should give
slightly better chance at avoiding oops after timeout.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Set the right DMA direction in the sdma_control(), else
we will get the wrong log when enable the DYNAMIC_DEBUG.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This patch adds power management support to the dma40
driver. The DMA registers are backed up and restored,
during suspend/resume. Also flags to track the dma usage
have been introduced to facilitate this. Patch also includes
few other minor changes, related to formatting, comments.
Signed-off-by: Narayanan G <narayanan.gopalakrishnan@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
[fixed direction enums and cyclic api based on changes
already merged]
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Define a new api that could be used for doing fancy data transfers
like interleaved to contiguous copy and vice-versa.
Traditional SG_list based transfers tend to be very inefficient in
such cases as where the interleave and chunk are only a few bytes,
which call for a very condensed api to convey pattern of the transfer.
This api supports all 4 variants of scatter-gather and contiguous transfer.
Of course, neither can this api help transfers that don't lend to DMA by
nature, i.e, scattered tiny read/writes with no periodic pattern.
Also since now we support SLAVE channels that might not provide
device_prep_slave_sg callback but device_prep_interleaved_dma,
remove the BUG_ON check.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Acked-by: Barry Song <Baohua.Song@csr.com>
[renamed dmaxfer_template to dma_interleaved_template
did fixup after the enum dma_transfer_merge]
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
On October 1 in 2011,
OKI SEMICONDUCTOR Co., Ltd. changed the company name in to LAPIS Semiconductor
Co., Ltd.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The individual SoC dependency in Kconfig hardly scales anymore.
Instead of having such a fine grained dependency just depend
on ARCH_MXC and risk that the uninformed user has to look in
the help text to figure out which driver is the correct one.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This patch adds to fix the build warning as following.
drivers/dma/pl330.c: In function 'pl330_probe':
drivers/dma/pl330.c:859: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Add device tree probe support for atmel at_hdmac DMA driver.
Bindings are added to specify DMA controller configuration.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
We remove the use of platform data from DMA controller driver.
We now use of .id_table to distinguish between compatible
types. The two implementations allow to determine the
number of channels and the capabilities of the controller.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (63 commits)
dmaengine: mid_dma: mask_peripheral_interrupt only when dmac is idle
dmaengine/ep93xx_dma: add module.h include
pch_dma: Reduce wasting memory
pch_dma: Fix suspend issue
dma/timberdale: free_irq() on an error path
dma: shdma: transfer based runtime PM
dmaengine: shdma: protect against the IRQ handler
dmaengine i.MX DMA/SDMA: add missing include of linux/module.h
dmaengine: delete redundant chan_id and chancnt initialization in dma drivers
dmaengine/amba-pl08x: Check txd->llis_va before freeing dma_pool
dmaengine/amba-pl08x: Add support for sg len greater than one for slave transfers
serial: sh-sci: don't filter on DMA device, use only channel ID
ARM: SAMSUNG: Remove Samsung specific enum type for dma direction
ASoC: Samsung: Update DMA interface
spi/s3c64xx: Merge dma control code
spi/s3c64xx: Add support DMA engine API
ARM: SAMSUNG: Remove S3C-PL330-DMA driver
ARM: S5P64X0: Use generic DMA PL330 driver
ARM: S5PC100: Use generic DMA PL330 driver
ARM: S5PV210: Use generic DMA PL330 driver
...
Fix up fairly trivial conflicts in
- arch/arm/mach-exynos4/{Kconfig,clock.c}
- arch/arm/mach-s5p64x0/dma.c
To support multi-size buffers in the mx3_camera V4L2 driver we have to be
able to stop DMA on a channel without releasing descriptors and completely
halting the hardware. Use the DMA_PAUSE control to implement this mode.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix files that were implicitly using module.h but not
calling it out for inclusion directly. We'll break those
once we remove the implicit presence otherwise
[With input from Uwe Kleine-König <u.kleine-koenig@pengutronix.de>]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files aren't just exporting symbols -- they are also defining
a MODULE_LICENSE etc. so give them the full module.h file.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The mask_peripheral_interrupt is called when channel wants to mask the
interrupt. Move this to suspend as this masking affects other channels
as well. Not touching unmask here and unmask would still be done of
first channel use
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Due to module.h cleanup it is not anymore included implicitly. Drivers who
want to use it need to include it explicitly.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
nr_channels is defined in "struct pch_dma".
and struct pch_dma_chan is defined in "struct pch_dma".
So, "sizeof(struct pch_dma_chan) * nr_channels" is unnecessary.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
There was an error path that skipped the free_irq() step by mistake.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently the shdma dmaengine driver uses runtime PM to save power, when
no channel on the specific controller is requested by a user. This patch
switches the driver to count individual DMA transfers. That way the
controller can be powered down between transfers, even if some of its
channels are in use.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The IRQ handler of the shdma driver accesses common hardware registers,
that are also accessed from other contexts. Therefore access to them
has to be performed with interrupts disabled, not only with disabled
bottom halves.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Add missing include of linux/module.h to fix build error.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_async_device_register will re-init chan_id and chancnt,
so whatever chan_id and chancnt are set in drivers, they will
be re-written by dma_async_device_register.
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Viresh Kumar <viresh.kumar@st.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Piotr Ziecik <kosmo@semihalf.com>
Cc: Yong Wang <yong.y.wang@intel.com>
Cc: Jaswinder Singh <jassi.brar@samsung.com>
Cc: Pelagicore AB <info@pelagicore.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In pl08x_free_txd(), check if pool is allocated successfully before freeing it.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Untill now, sg_len greater than one is not supported. This patch adds support to
do that.
Note: Still, if peripheral is flow controller, sg_len can't be greater that one.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds DMA_CYCLIC capability that is used for audio driver.
DMA driver activated with it reuses the dma requests that were submitted
through tx_submit().
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Original code carries out the start operation after flush operation.
But start operation is not required for DMA_TERMINATE_ALL command.
So, this patch removes the unnecessary start operation and only carries out
the flush operation for handling DMA_TERMINATE_ALL command.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
[Fixed typos in changelog]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch updates following 3 items.
1. Removes unneccessary code.
2. Add AMBA, PL330 configuration
3. Change the meaning of 'peri_id' variable
from PL330 event number to specific dma id by user.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The bank_lock can be taken in atomic context (irq handling)
and therefore cannot be preempted on -rt - annotate it.
In mainline this change documents the low level nature of
the lock - otherwise there's no functional difference. Lockdep
and Sparse checking will work as usual.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: kernel@pengutronix.de
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Link: http://lkml.kernel.org/r/1311949627-13260-1-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Before converting the dma channel to our private data structure, first
check that the channel is indeed one which our driver registered. We
do this by ensuring that the underlying device is bound to our driver.
This avoids potential oopses if we try to reference 'plchan->name'
against a foreign drivers dma channel.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Prepared descriptors that are not submitted will not be freed. Add
prepared descriptor to a list to be able to release them upon
dmaengine_terminate_all().
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The client list may exist in two lists at the same time. This makes free
fail since the same desc is freed multiple times. Remove desc from
client list when adding it to the pending queue. Move free of client owned
descriptors from free_dma() to terminate_all().
Unable to handle kernel paging request at virtual address 00100104
pgd = dea8c000
[00100104] *pgd=1ea62831, *pte=00000000, *ppte=00000000
Internal error: Oops: 817 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 Not tainted (3.1.0-rc3+ #58)
PC is at d40_free_chan_resources+0x64/0x330
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Prepared descriptors that are not submitted will not be freed. Add
prepared descriptor to a list to be able to release them upon
dmaengine_terminate_all().
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The client list may exist in two lists at the same time. This makes free
fail since the same desc is freed multiple times. Remove desc from
client list when adding it to the pending queue. Move free of client owned
descriptors from free_dma() to terminate_all().
Unable to handle kernel paging request at virtual address 00100104
pgd = dea8c000
[00100104] *pgd=1ea62831, *pte=00000000, *ppte=00000000
Internal error: Oops: 817 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 Not tainted (3.1.0-rc3+ #58)
PC is at d40_free_chan_resources+0x64/0x330
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The firmware blob may not be available when the driver
probes. Instead of blocking the whole kernel use
request_firmware_nowait() and continue without firmware.
The ROM scripts can already be used then if available.
For the devicetree case the ROM scripts are not available,
still the probe function should not block. The driver
will be unusable in this case, but we have no way of
detecting this properly. The configuration of the dma
channels will fail, so nothing bad should happen.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If we do not have a firmare script for a given transfer,
the setup of this channel must fail. For this the script
addresses have to be < 0 initially, not 0.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
channel0 of the sdma engine is the configuration channel. It
is a shared resource and thus must be protected by a mutex.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Making dmatest threads freezable allows its use for system PM testing.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
At least, on SPEAr platforms there is one peripheral, JPEG, which can be flow
controller for DMA transfer. Currently DMA controller driver didn't support
peripheral flow controller configurations.
This patch adds device_fc field in struct pl08x_channel_data, which will be used
only for slave transfers and is not used in case of mem2mem transfers.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When we have DMA transfers between peripheral and memory, then we shouldn't
reduce width of peripheral at all, as that may be a strict requirement. But we
can always reduce width of memory access, with some compromise in performance.
Thus, we must select peripheral as master and not memory.
Also this rearranges code to make it shorter.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently lli_len is aligned to min of two widths, which looks to be incorrect.
Instead it should be aligned to max of both widths.
Lets say, total_size = 441 bytes
MIN: lets check if min() suits or not:
CASE 1: srcwidth = 1, dstwidth = 4
min(src, dst) = 1
i.e. We program transfer size in control reg to 441.
Now, till 440 bytes everything is fine, but on the last byte DMAC can't transfer
1 byte to dst, as its width is 4.
CASE 2: srcwidth = 4, dstwidth = 1
min(src, dst) = 1
i.e. we program transfer size in control reg to 110 (data transferred = 110 * srcwidth).
So, here too 1 byte is left, but on the source side.
MAX: Lets check if max() suits or not:
CASE 3: srcwidth = 1, dstwidth = 4
max(src, dst) = 4
Aligned size is 440
i.e. We program transfer size in control reg to 440.
Now, all 440 bytes will be transferred without any issues.
CASE 4: srcwidth = 4, dstwidth = 1
max(src, dst) = 4
Aligned size is 440
i.e. We program transfer size in control reg to 110 (data transferred = 110 * srcwidth).
Now, also all 440 bytes will be transferred without any issues.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Code for creating single byte llis is present at several places. Create a
routine to avoid code redundancy.
Also, we don't need one lli per single byte transfer, we can have single lli to
do all single byte transfer.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
max_bytes_per_lli = bd.srcbus.buswidth * PL080_CONTROL_TRANSFER_SIZE_MASK;
This is confirmed by ARM support guys.
Below is summary of mail exchange with them:
[Viresh] What is the total data to be transferred in case source and destination
bus widths are different. Suppose, source bus width is 2 bytes and destination
is 4 bytes. Now in order to transfer 80 bytes, what should be value of
TransferSize field in control reg: 40? or 20?.
[David from ARM] The value that is programmed into the TransferSize field should
be the number of <SourceWidth> transfers needed to achieve the required data
transfer.
So, to transfer 80 bytes, with a Source Width of 2, the TransferSize field =
should be programmed with:
Total transfer size
------------------- = 40
<source width>
[Viresh] Will this change if source is 4 bytes and dest is 2?
[David] Yes - the calculation then becomes:
Total transfer size
------------------- =20
<source width>
Also, max_bytes_per_lli must be calculated after fixing src and dest widths not
before that. So move this code to the correct place.
This patch also removes max_bytes_per_lli from earlier print message, as till
that point max_bytes_per_lli is unknown.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pl080 Manual says: "Bursts do not cross the 1KB address boundary"
We can program the controller to cross 1 KB boundary on a burst and controller
can take care of this boundary condition by itself.
Following is the discussion with ARM Technical Support Guys (David):
[Viresh] Manual says: "Bursts do not cross the 1KB address boundary"
What does that actually mean? As, Maximum size transferable with a single LLI is
4095 * 4 =16380 ~ 16KB. So, if we don't have src/dest address aligned to burst
size, we can't use this big of an LLI.
[David] There is a difference between bursts describing the total data
transferred by the DMA controller and AHB bursts. Bursts described by the
programmable parameters in the PL080 have no direct connection with the bursts
that are seen on the AHB bus.
The statement that "Bursts do not cross the 1KB address boundary" in the TRM is
referring to AHB bursts, where this limitation is a requirement of the AHB spec.
You can still issue bursts within the PL080 that are in excess of 1KB. The
PL080 will make sure that its bursts are broken down into legal AHB bursts which
will be formatted to ensure that no AHB burst crosses a 1KB boundary.
Based on above discussion, this patch removes all code related to 1 KB boundary
as we are not required to handle this in driver.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently, if error interrupt occurs, nothing is done in interrupt handler (just
clearing the interrupts). We must somehow indicate this to the user that DMA is
over, due to ERR interrupt or TC interrupt.
So, this patch just schedules existing tasklet, with a print showing error
interrupt has occurred on which channels.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We have just executed following in pl08x_get_phy_channel():
ch->signal = -1;
We don't have to compare "ch->signal < 0", as this will always be true.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Simply writing 1 on bit 0 is sufficient instead of reading and clearing bits.
Also as per manual, for bit 3-31 of DMACConfiguration register:
"read undefined, write as 0"
So, we must not rely on values read from this registers bit 3-31.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Insert notifiers for the runtime PM API. With this the runtime PM layer kicks in
to action where used.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
For 8 memory and 16 slave channels 35 boot print lines are printed. And that is
too much. Most of this would be more useful for debugging. So moving few of them
to dev_dbg instead of dev_info. Now only 3 prints will be printed.
This also rearrange one of the debug message to fit into two lines.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Similar comment is present over routine also pl08x_choose_master_bus(). Keeping
one of them. Also rewrite that comment to convey message clearly.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As mentioned in Documentation/CodingStyle,
The preferred form for passing a size of a struct is the following:
p = kmalloc(sizeof(*p), ...);
The alternative form where struct name is spelled out hurts readability and
introduces an opportunity for a bug when the pointer variable type is changed
but the corresponding sizeof that is passed to a memory allocator is not.
This patch replaces (struct xyz) with *ptr at several occurrences in driver.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Header files included in driver are not present in alphabetical order. Rearrange
them in alphabetical order.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There were few formatting related issues in code. This patch fixes them.
Fixes include:
- Remove extra blank lines
- align code to 80 cols
- combine several lines to one line
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In this driver, we can trigger cyclic transfer on peripherals-DMA interfaces.
It is dependent on driver implementation but cannot depend on a platform
property: we remove the dma_has_cap(DMA_CYCLIC, ) test which has no meaning.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Cyclic property and paused state are encoded as bits in the channel status
bitfield. Tests of those bits are wrapped in convenient helper functions.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Save/restore dma controller state across a suspend-resume sequence.
The prepare() function will wait for the non-cyclic channels to become idle.
It also deals with cyclic operations with the start at next period while
resuming.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dmaengine routines can be called from interrupt context and with
interrupts disabled. Whereas spin_unlock_bh can't be called from
such contexts. So this patch converts all spin_lock* routines
to irqsave variants.
Also, spin_lock() used in tasklet is converted to irqsave variants,
as tasklet can be interrupted, and dma requests from such interruptions
may also call spin_lock.
Idea from dw_dmac patch by Viresh Kumar.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
After calling mxs_dma_disable_chan() for a channel, that channel
becomes unusable because some controller registers can only be written
when the clock is enabled via CLKGATE.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: drop experimental status for ARM_PATCH_PHYS_VIRT
ARM: 7008/1: alignment: Make SIGBUS sent to userspace POSIXly correct
ARM: 7007/1: alignment: Prevent ignoring of faults with ARMv6 unaligned access model
ARM: 7010/1: mm: fix invalid loop for poison_init_mem
ARM: 7005/1: freshen up mm/proc-arm946.S
dmaengine: PL08x: Fix trivial build error
ARM: Fix build error for SMP=n builds
Something changed during the 3.1 merge window in the include files
which now causes the pl08x DMA engine driver to fail to build. Fix
this by adding the now necessary dma-mapping.h include:
drivers/dma/amba-pl08x.c: In function ■pl08x_unmap_buffers■:
drivers/dma/amba-pl08x.c:1524: error: implicit declaration of function ■dma_unmap_single■
drivers/dma/amba-pl08x.c:1527: error: implicit declaration of function ■dma_unmap_page■
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In case, some error occurs while doing memcpy transfers, we must terminate all
transfers physically too. This is achieved by calling device_control() routine
with TERMINATE_ALL as parameter.
This is also required to be done in case module is removed while we are in
middle of some transfers.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmaengine: use DEFINE_IDR for static initialization
ioat: fix xor_idx_to_desc
Avoid section type conflict in dma/ioat/dma_v3.c
ioat: Adding PCI IDs for IOAT devices on SandyBridge platforms
We could use DEFINE_IDR for statically allocated idr
that allow us to save a few lines of code.
And also remove unneeded mutex_init() for dma_list_mutex, as
dma_list_mutex is initialized automatically by DEFINE_MUTEX().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
For versions of the device that implement operation-types 0x87, 0x88
(IOAT_OP_XOR, IOAT_OP_XOR_VAL) this map determines whether a given
source is located in the base or extended descriptor. Source addresses
6 through 8 require an extended descriptor, hence 0xe0, not 0xd0. No
shipping hardware currently implements these operation types.
Reported-by: Evgueni Smogailov <evgueni.smogailov@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
It does not need to allocate space and copy fw_name in function
sdma_get_firmware().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
It might be not good to use software defined version to identify sdma
device type, when hardware does not define such version. Instead,
soc name is stable enough to define the device type.
The patch uses platform_device_id rather than version number passed
by platform data to identify sdma device type/version.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Vinod Koul <vinod.koul@intel.com>
pl08x_width function does not handle rest of enums for DMA_SLAVE_BUSWIDTH_xxxx
which causes gcc to emit below warining
drivers/dma/amba-pl08x.c: In function 'pl08x_width':
drivers/dma/amba-pl08x.c:1119: warning: enumeration value
'DMA_SLAVE_BUSWIDTH_UNDEFINED' not handled in switch
drivers/dma/amba-pl08x.c:1119: warning: enumeration value
'DMA_SLAVE_BUSWIDTH_8_BYTES' not handled in switch
this patch adds a default case which returns error
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that we have separate cctl values for M>P and P>M transfers, we can
avoid calculating the cctl value each time we prepare a transaction.
Move the bus selection and increment setting to the slave configuration
and initialization functions.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Store the source/destination cctl values into the channel structure.
This moves us towards being able to avoid a configuration call each
time we use the channel.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Store the source/destination slave address separately into the channel
structure. This moves us towards being able to avoid a configuration
call each time we use the channel.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Clean up debugging when setting up the LLI list. This reduces the
amount of output while preserving the information, and makes it easier
to read.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Avoid re-selecting the LLI bus each time we create an LLI. Move it out
of the LLI setup loops.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
PL08X_WQ_PERIODMIN and PL08X_MAX_ALLOCS are not used, remove them.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We met some channels in abnormal state after disable.
Reset it to get a clean state.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Call pci_set_drvdata() once in intel_mid_dma_probe() is enough.
Remove redundant pci_set_drvdata() calls in dma_suspend() and dma_resume().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The pl330 needs platform data for describing peripheral connections, but
some platforms may only support memory to memory dma channels. In this
case, we can probe for how many channels there are and don't need the
platform data.
As memcpy requests don't need channel private data to hold peripheral
info, allow private data to be NULL in this case.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Cc: Vinod Koul <vkoul@infradead.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
* 'next/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (35 commits)
ARM: msm: platsmp: determine number of CPU cores at boot time
ARM: Tegra: Seaboard: Fix I2C bus numbering for ADT7461
ARM: Tegra: Trimslice: Tri-state DAP3 pinmux
ARM: orion5x: fixup 5181 MPP mask check
ARM: mxs-dma: include <linux/dmaengine.h>
ARM: i.MX53: consistently use MX53_UART_PAD_CTRL for uart txd/rxd/rts/cts
ARM: i.MX53: UARTn_CTS pin should not change RTS input select
ARM: i.MX53: UARTn_TXD pin should not change RXD input select
ARM: mx25: Fix typo on CAN1_RX pad setting
iomux-mx53: add missing 'IOMUX_CONFIG_SION' for some I2C pad definitions
ARM: NUC93X: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: LPC32XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: CNS3XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: i.MX53: Fix IOMUX type o's
ARM i.MX dma: Fix burstsize settings
mach-mx5: fix the I2C clock parents
ARM: mxs/tx28: according to the TX28's datasheet D4-D7 are not used for MMC0
ARM i.MX23/28: platform-mxsfb: Add missing include of linux/dma-mapping.h
ARM: mx53: Fix some interrupts marked as reserved.
MXC: iomux-v3: correct NO_PAD_CTRL definition
...
Fix up trivial conflict in arch/arm/mach-imx/mach-mx31_3ds.c
Currently, Mode-Control register is accessed by read-modify-write.
According to DMA hardware specifications datasheet, prohibits this method.
Because this register resets to 0 by DMA HW after DMA transfer completes.
Thus, current read-modify-write processing can cause unexpected behavior.
The datasheet says in case of writing Mode-Control register, set the value for only target channel, the others must set '11b'.
e.g. Set DMA0=01b DMA11=10b
CTL0=33333331h
CTL2=00002333h
NOTE:
CTL0 includes DMA0~7 Mode-Control register.
CTL2 includes DMA8~11 Mode-Control register.
This patch modifies the issue.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
spi/imx: add device tree probe support
spi/imx: copy gpio number passed by platform data into driver private data
spi/imx: use soc name in spi device type naming scheme
spi/imx: merge type SPI_IMX_VER_0_7 into SPI_IMX_VER_0_4
spi/imx: do not use spi_imx2_3 to name SPI_IMX_VER_2_3 function and macro
spi/imx: use mx21 to name SPI_IMX_VER_0_0 function and macro
spi/imx: do not make copy of spi_imx_devtype_data
spi/dw: Add spi number into spi irq desc
spi/tegra: Use engineering names in DT compatible property
spi/fsl_spi: fix CPM spi driver
mach-s3c2410: remove unused spi-gpio.h file
spi: remove obsolete spi-s3c24xx-gpio driver
mach-gta2: remove unused spi-gpio.h include
mach-qt2410: convert to spi_gpio
mach-jive: convert to spi_gpio
spi/pxa2xx: Remove unavailable ssp_type from documentation
spi/bfin_spi: uninline fat queue funcs
spi/bfin_spi: constify pin array
spi/bfin_spi: use structs for accessing hardware regs
spi/topcliff-pch: Support new device ML7223 IOH
...
Fix up trivial conflict in arch/arm/mach-ep93xx/Makefile
const __read_mostly is not legal and causes section type conflicts.
That's because the read.mostly section is not read only.
Simply drop the __read_mostly designation.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
[drop __read_mostly instead of const]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Adding to pci_id.h and the device table for ioat.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In general, the mxs-dma users get separate irq for each channel,
but gpmi is special one which has only one irq shared by all gpmi
channels. It causes mxs_dma channel allocation function fail for
all other gpmi channels except the first one calling into the
function.
The patch gets request_irq call skipped for NO_IRQ case, and leaves
this gpmi specific quirk to gpmi driver to sort out. It will fix
above problem if gpmi driver sets chan_irq as gpmi irq for only one
channel and NO_IRQ for all the rest channels.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
While testing Per Forlins MMC speed improvements I noticed a
semantic bug in the COH901318 driver: it will write to channel
registers in the prep_slave_sg() function, instead of deferring
it to later, breaking the assumption from the drivers to be able
to queue up new jobs while another job is running. Fix this by
storing up the initial register writes in the job descriptors
and write them to hardware when we process the descriptor
instead. Now the stress tests work.
Acked-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently the runtime config implementation forces the memory side
parameters to be the same as the peripheral side. Allow these to be
different, and check for misconfiguration.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Ulf HANSSON <ulf.hansson@stericsson.com>
Tested-by: Stefan Nilsson <stefan.xk.nilsson@stericsson.com>
Reviewed-by: Per Forlin <per.forlin@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Robert Marklund <robert.marklund@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The DMA40 is not a PrimeCell from ARM, but it still use the same
ID registers. So let's utilize the existing macros in the
PrimeCell header to identify manufacturer and revision of the IP
block instead of reinventing the wheel.
Cc: Robert Marklund <robert.marklund@stericsson.com>
Cc: Per Forlin <per.forlin@linaro.org>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This function may be initiated from IRQ context, so the allocation
must allocate NOWAIT memory.
Signed-off-by: Robert Marklund <robert.marklund@stericsson.com>
Reviewed-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Philippe Langlais <philippe.langlais@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
ste_dma40 now implements issue_pending according to documentation.
Submit adds descriptos to a pending queue with are flushed down to the DMAC
at issue_pending.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
tx_submit will add descriptors to the pending queue. Issue pending
will then move the pending descriptors to the transfer queue.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It is not good to have cpu_name and to_version encoded into sdma
firmware name as variables. For example, there are three TOs of
imx51 soc, the sdma script never changes since TO1, which means
all three TOs of imx51 uses TO1 version of sdma script. But we
have to prepare three identical firmwares, sdma-imx51-to1.bin
sdma-imx51-to2.bin and sdma-imx51-to3.bin, to have the kernel
capable of running on all three TOs.
The patch removes cpu_name and to_version from sdma platform data,
and instead uses fw_name to pass the firmware name, so that we can
pass the TO version where it's relevant and skip it where only one
firmware exists.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
dmaengine expects the maxburst parameter in words, not bytes.
The imxdma driver and its users do this wrong. Fix this.
As a side note the imx-pcm-dma-mx2 driver was 'fixed' to work
with imx-dma. This broke the driver with imx-sdma support which
correctly takes the maxburst parameter in words. This patch
puts the sdma based sound back to work.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There exist systems with multiple DMA controllers with different
capabilities. For example, on some sh-mobile / rmobile systems there are
DMA controllers, whose channels can be configured to be used with
SD- and MMC-host controllers, serial ports etc. Besides there are also
DMA controllers, that can only be used for one special function, e.g.,
for USB. In such cases the DMA client filter function can just choose
to specify to the DMA driver, which channel it needs. Then the
.device_alloc_chan_resources() method of the DMA driver will check,
whether it can provide that dunction. If not, it will fail and the loop
in __dma_request_channel() will continue to the next DMA device, until
it finds a suitable one. This works fine with just one minor glitch:
the kernel logs error messages like
dmaengine: failed to get <channel name>: (-<error code>)
after each such non-critical failure. This patch lowers priority of
this message to the debug level.
Reported-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Remove linux/mm.h inclusion from netdevice.h -- it's unused (I've checked manually).
To prevent mm.h inclusion via other channels also extract "enum dma_data_direction"
definition into separate header. This tiny piece is what gluing netdevice.h with mm.h
via "netdevice.h => dmaengine.h => dma-mapping.h => scatterlist.h => mm.h".
Removal of mm.h from scatterlist.h was tried and was found not feasible
on most archs, so the link was cutoff earlier.
Hope people are OK with tiny include file.
Note, that mm_types.h is still dragged in, but it is a separate story.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IE bit position on CHCR register is not same in all DMAC.
This patch adds new "chcr_ie_bit" to decide it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CHCR register position is not same in all DMAC.
This patch adds new "chcr_offset" to decide it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
chan_pdata->dmars_bit is unsigned int
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
It is not readable that there is any spin_unlock_bh on same function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds "to_sh_dev" macro, and clean up codes.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The symbol 'ep93xx_dma_prep_dma_memcpy' is only used in this driver
and should be marked static.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Mika Westerberg <mika.westerberg@iki.fi>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix the recently added SH_DMAC_MAX_CHANNELS handling code in
300e5f9 dmaengine: shdma: Fix SH_DMAC_MAX_CHANNELS handling
Without this fix the shdma driver outputs silly messages in
case SH_DMAC_MAX_CHANNELS happens to match the platform data:
sh-dma-engine sh-dma-engine.0: Attempting to register 20 DMA channels when a max
imum of 20 are supported.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The ep93xx DMA controller has 10 independent memory to peripheral (M2P)
channels, and 2 dedicated memory to memory (M2M) channels. M2M channels can
also be used by SPI and IDE to perform DMA transfers to/from their memory
mapped FIFOs.
This driver supports both M2P and M2M channels with DMA_SLAVE, DMA_CYCLIC and
DMA_MEMCPY (M2M only) capabilities.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The ep93xx DMA controller has 10 independent memory to peripheral (M2P)
channels, and 2 dedicated memory to memory (M2M) channels. M2M channels can
also be used by SPI and IDE to perform DMA transfers to/from their memory
mapped FIFOs.
This driver supports both M2P and M2M channels with DMA_SLAVE, DMA_CYCLIC and
DMA_MEMCPY (M2M only) capabilities.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
A recent patch has introduced a regression, where repeating a memcpy
DMA test with shdma module unloading between them skips the DMA channel
configuration. Fix this regression by always configuring the channel
during its allocation.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
ISSUE: In case PCH_DMA with I2S communications with ch8~ch11, sometimes I2S data
is not send correctly.
CAUSE: The following patch I submitted before was not enough modification for
supporting DMA ch8~ch11. The modification for status register of ch8~11 was not
enough.
pch_dma: Support I2S for ML7213 IOH
author Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Mon, 9 May 2011 07:09:38 +0000 (16:09 +0900)
committer Vinod Koul <vinod.koul@intel.com>
Mon, 9 May 2011 11:42:23 +0000 (16:42 +0530)
commit 194f5f2706
tree c9d4903ea0
parent 60092d0bde
This patch fixes the issue.
We can confirm PCH_DMA with I2S communications with ch8~ch11 works well.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (33 commits)
x86: poll waiting for I/OAT DMA channel status
maintainers: add dma engine tree details
dmaengine: add TODO items for future work on dma drivers
dmaengine: Add API documentation for slave dma usage
dmaengine/dw_dmac: Update maintainer-ship
dmaengine: move link order
dmaengine/dw_dmac: implement pause and resume in dwc_control
dmaengine/dw_dmac: Replace spin_lock* with irqsave variants and enable submission from callback
dmaengine/dw_dmac: Divide one sg to many desc, if sg len is greater than DWC_MAX_COUNT
dmaengine/dw_dmac: set residue as total len in dwc_tx_status if status is !DMA_SUCCESS
dmaengine/dw_dmac: don't call callback routine in case dmaengine_terminate_all() is called
dmaengine: at_hdmac: pause: no need to wait for FIFO empty
pch_dma: modify pci device table definition
pch_dma: Support new device ML7223 IOH
pch_dma: Support I2S for ML7213 IOH
pch_dma: Fix DMA setting issue
pch_dma: modify for checkpatch
pch_dma: fix dma direction issue for ML7213 IOH video-in
dmaengine: at_hdmac: use descriptor chaining help function
dmaengine: at_hdmac: implement pause and resume in atc_control
...
Fix up trivial conflict in drivers/dma/dw_dmac.c
For certain system configurations a 5 usec udelay before checking I/OAT DMA
channel status is sometimes not sufficient, resulting in a false failure
status and unnecessary freeing of channel resources. Conversely, for many
configurations 5 usec is longer than necessary.
Loop for up to 20 usec waiting for successful status before failing.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
With the addition of a device platform mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Nobody is currently maintaining dw_dmac. We are using dw_dmac for SPEAr13xx and
are currently maintaining it. After discussing with Vinod, sending this patch to
update maintainer-ship of dw_dmac.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Havard Skinnemoen <hskinnemoen@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Update SH_DMAC_MAX_CHANNELS to support the 20 DMA
channels included in the sh73a0 SY-DMAC hardware.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the shdma.c handing of SH_DMAC_MAX_CHANNELS
to avoid overwriting the chan_irq[] and chan_flag[]
arrays in the case of pdata->channel_num is larger
than SH_DMAC_MAX_CHANNELS.
With this patch applied up to SH_DMAC_MAX_CHANNELS
will be used by the shdma.c driver. If more channels
are available in the platform data the user will
be notified on the console.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch makes the shdma.c driver allow slave operation
on DMA hardware mapped with a single I/O-memory window.
The dmae_set_dmars() function is adjusted to use the
first memory window in case of a missing DMARS window.
At probe() time the code is updated to enable DMA_SLAVE
only if slave information is passed with the platform data.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'sh-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
sh: Ignore R_SH_NONE module relocations.
SH: SE7751: Fix pcibios_map_platform_irq prototype.
sh: remove warning and warning_symbol from struct stacktrace_ops
sh: wire up sys_sendmmsg.
clocksource: sh_tmu: Runtime PM support
clocksource: sh_tmu: __clocksource_updatefreq_hz() update
clocksource: sh_cmt: Runtime PM support
clocksource: sh_cmt: __clocksource_updatefreq_hz() update
dmaengine: shdma: synchronize RCU before freeing, simplify spinlock
dmaengine: shdma: add runtime- and system-level power management
dmaengine: shdma: fix locking
sh: sh-sci: sh7377 and sh73a0 build fixes
sh: cosmetic improvement: use an existing pointer
serial: sh-sci: suspend/resume wakeup support V2
serial: sh-sci: Runtime PM support
sh: select IRQ_FORCED_THREADING.
sh: intc: Set virtual IRQs as nothread.
sh: fixup fpu.o compile order
i2c: add a module alias to the sh-mobile driver
ALSA: add a module alias to the FSI driver
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
After discovering that wide use of prefetch on modern CPUs
could be a net loss instead of a win, net drivers which were
relying on the implicit inclusion of prefetch.h via the list
headers showed up in the resulting cleanup fallout. Give
them an explicit include via the following $0.02 script.
=========================================
#!/bin/bash
MANUAL=""
for i in `git grep -l 'prefetch(.*)' .` ; do
grep -q '<linux/prefetch.h>' $i
if [ $? = 0 ] ; then
continue
fi
( echo '?^#include <linux/?a'
echo '#include <linux/prefetch.h>'
echo .
echo w
echo q
) | ed -s $i > /dev/null 2>&1
if [ $? != 0 ]; then
echo $i needs manual fixup
MANUAL="$i $MANUAL"
fi
done
echo ------------------- 8\<----------------------
echo vi $MANUAL
=========================================
Signed-off-by: Paul <paul.gortmaker@windriver.com>
[ Fixed up some incorrect #include placements, and added some
non-network drivers and the fib_trie.c case - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
List elements, deleted using list_del_rcu(), cannot be freed without
synchronising RCU. Further, the spinlock, used to protect the RCU
writer, is called in process context, so, we don't have to save flags.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch extends and fixes runtime power management in the shdma
driver to support powering down the DMA controller and adds support
for system-level suspend and resume.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Close multiple theoretical races, especially the one in
.device_free_chan_resources().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move the dmaengine subsystem up early in the drivers Makefile so
DMA is made available early to all drivers, just like e.g.
regulators. Now even regulators can use DMA on the same initlevel.
As a result we can bump the ste_dma40 and coh901318 dmaengine
drivers down one initlevel to subsys_init().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Some peripherals like amba-pl011 needs pause to be implemented in DMA controller
drivers. This also returns correct status from dwc_tx_status() in case chan is
paused.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dmaengine routines can be called from interrupt context and with interrupts
disabled. Whereas spin_unlock_bh can't be called from such contexts. So this
patch converts all spin_*_bh routines to irqsave variants.
Also, spin_lock() used in tasklet is converted to irqsave variants, as tasklet
can be interrupted, and dma requests from such interruptions may also call
spin_lock.
Now, submission from callbacks are permitted as per dmaengine framework. So we
shouldn't hold any locks while calling callbacks. As locks were taken by parent
routines, so releasing them before calling callbacks doesn't look clean enough.
So, locks are taken inside all routine now, whereever they are required. And
dwc_descriptor_complete is always called without taking locks.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If len passed in sg for slave_sg transfers is greater than DWC_MAX_COUNT, then
driver programmes controller incorrectly. This patch adds code to handle this
situation by allocation more than one desc for same sg.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If transfer status is !=DMA_SUCCESS, return total transfer len as residue,
instead of zero.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If dmaengine_terminate_all() is called for dma channel, then it doesn't make
much sense to call registered callback routine. While in case of success or
failure it must be called.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
With the addition of the "pause" feature, an active wait was introduced
to check the "FIFO empty" event. This event was not always happening and
a timout contition was needed.
But, in some cases, this event depend on the peripheral connected to the
channel that is paused: FIFO becomes empty if the peripheral consumes data.
The timeout is pretty difficult to evaluate. Moreover, this check is not
needed.
In conclusion, it seems sensible to entirely remove the checking of
"FIFO empty" status when pausing.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[commit msg edited for grammer]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently, Direct-Start mode(*) is enabled.
Our IOH's devices must not use this mode.
This causes unexpected behavior.
This patch deletes Direct-Start setting.
(*) This mode is used in order for CPU to generate the DMA request.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently, even-channel number is set as tx direction and odd is set as rx.
However, though video-in uses ch6, the direction is not tx but rx.
This patch sets video-in's DMA direction correctly.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
A little function helps to chain descriptors:
it is already used in cyclic dma operations, now use it in memcpy and slave_sg
preparation functions.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pause and resume controls are useful for audio devices. This also returns
correct status from atc_tx_status() in case chan is paused.
Idea from dw_dmac patch by Linus Walleij.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If transfer status is !=DMA_SUCCESS, return total transfer len as residue,
instead of zero.
Idea from dw_dmac patch by Viresh Kumar.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The compiler nowadays moans about possibly non-assigned variable.
Fix this by default-assigning 0.
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
DMA controller has two AHB interfaces on the SOC internal
matrix.
It is more efficient to specialize each interface as the
access to memory can introduce latencies that are not compatible
with peripheral accesses requirements.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is no need to test if channel is enabled in tasklet:
- in error path, channel is disabled in interrupt routine
- in normal path, this test is performed in sub functions to report
a misuse of the engine.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now we use Buffer Transfer Completed interrupts. If we
want a chained buffer completed information, we setup the
ATC_IEN bit in CTRLB register in the lli.
This is done by set_desc_eol() function and used by
memcpy/slave_sg functions.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Using C line continuation inside format strings is error prone.
Clean up the unintended whitespace introduced by misuse of \.
Neaten correctly used line continations as well for consistency.
drivers/scsi/arcmsr/arcmsr_hba.c has these errors as well,
but arcmsr needs a lot more work and the driver should likely be
moved to staging instead.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'spi/merge' of git://git.secretlab.ca/git/linux-2.6:
dt/fsldma: fix build warning caused by of_platform_device changes
spi: Fix race condition in stop_queue()
gpio/pch_gpio: Fix output value of pch_gpio_direction_output()
gpio/ml_ioh_gpio: Fix output value of ioh_gpio_direction_output()
gpio/pca953x: fix error handling path in probe() call
Commit 000061245a, "dt/powerpc:
Eliminate users of of_platform_{,un}register_driver" forgot to convert
the type of structure passed into platform_device_register() when it
was converted from of_platform_device_register. Fix it.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In the function pdc_desc_get(), var 'i' is not
initialized before use. This patch fixes it.
Signed-off-by: Liu Yuan <tailai.ly@taobao.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use the correct api in probe to enable runtime pm for this driver.
Additionally, do not just call legacy suspend for runtime_suspend,
as this duplicates some work the pci core does for you.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch makes BUG_ON() usage correct in drivers/dma/ppc4xx/adam.c
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Sean MacLennan <smaclennan@pikatech.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Coly Li <bosong.ly@taobao.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch makes BUG_ON() usage correct in drivers/dma/mv_xor.c
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Coly Li <bosong.ly@taobao.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch makes BUG_ON() usage correct in drivers/dma/iop-adma.c.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Coly Li <bosong.ly@taobao.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dwc_scan_descriptors scans all descriptors from active_list in case transfer is
not completed. It compares first_desc->lli.llp, and then all childrens of its
tx_list. But it doesn't compare its own address, i.e. first_desc->txd.phys, as
this is what we have initially programmed into the controller register. So this
causes dma to stop and finish a transfer, which was never started. And thus
fail.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The irq numbers of tranfer end and address error are assigned same number
on some CPU. So the sh_dmae_err() should check the AE flag in DMAOR.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'irq-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tile: Use generic show_interupts()
tile: Convert to new irq function names
dma: Ipu: Convert interupt code
Convert to the new irq chip functions and cleanup the name space.
[ Guennadi reported: irq_data_get_chip_data is undefined. Yes, I screwed up.
it needs to be irq_data_get_irq_chip_data ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Dan Williams <dan.j.williams@intel.com>
LKML-Reference: <alpine.LFD.2.00.1103251220000.31464@localhost6.localdomain6>
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Note that the mfd's platform_data is marked __devinitdata. This
is still correct in all cases except for the timbgpio driver, whose
remove hook has been changed to no longer reference the pdata.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (66 commits)
avr32: at32ap700x: fix typo in DMA master configuration
dmaengine/dmatest: Pass timeout via module params
dma: let IMX_DMA depend on IMX_HAVE_DMA_V1 instead of an explicit list of SoCs
fsldma: make halt behave nicely on all supported controllers
fsldma: reduce locking during descriptor cleanup
fsldma: support async_tx dependencies and automatic unmapping
fsldma: fix controller lockups
fsldma: minor codingstyle and consistency fixes
fsldma: improve link descriptor debugging
fsldma: use channel name in printk output
fsldma: move related helper functions near each other
dmatest: fix automatic buffer unmap type
drivers, pch_dma: Fix warning when CONFIG_PM=n.
dmaengine/dw_dmac fix: use readl & writel instead of __raw_readl & __raw_writel
avr32: at32ap700x: Specify DMA Flow Controller, Src and Dst msize
dw_dmac: Setting Default Burst length for transfers as 16.
dw_dmac: Allow src/dst msize & flow controller to be configured at runtime
dw_dmac: Changing type of src_master and dest_master to u8.
dw_dmac: Pass Channel Priority from platform_data
dw_dmac: Pass Channel Allocation Order from platform_data
...
When we try to test all channels present on our controller together, some
channels of lower priority may be very slow as compared to others. If number of
transfers is unlimited, some channels may timeout and will not finish within 3
seconds. Thus, while doing such regress testing we may need to have higher value
of timeouts. This patch adds support for passing timeout value via module
parameters. Default value is 3 msec, a negative value means max timeout
possible.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
As a side effect this makes IMX_DMA selectable on i.MX21 again, because
the symbol ARCH_MX21 doesn't exist (MACH_MX21 would have been more correct).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6: (25 commits)
video: change to new flag variable
scsi: change to new flag variable
rtc: change to new flag variable
rapidio: change to new flag variable
pps: change to new flag variable
net: change to new flag variable
misc: change to new flag variable
message: change to new flag variable
memstick: change to new flag variable
isdn: change to new flag variable
ieee802154: change to new flag variable
ide: change to new flag variable
hwmon: change to new flag variable
dma: change to new flag variable
char: change to new flag variable
fs: change to new flag variable
xtensa: change to new flag variable
um: change to new flag variables
s390: change to new flag variable
mips: change to new flag variable
...
Fix up trivial conflict in drivers/hwmon/Makefile
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (47 commits)
doc: CONFIG_UNEVICTABLE_LRU doesn't exist anymore
Update cpuset info & webiste for cgroups
dcdbas: force SMI to happen when expected
arch/arm/Kconfig: remove one to many l's in the word.
asm-generic/user.h: Fix spelling in comment
drm: fix printk typo 'sracth'
Remove one to many n's in a word
Documentation/filesystems/romfs.txt: fixing link to genromfs
drivers:scsi Change printk typo initate -> initiate
serial, pch uart: Remove duplicate inclusion of linux/pci.h header
fs/eventpoll.c: fix spelling
mm: Fix out-of-date comments which refers non-existent functions
drm: Fix printk typo 'failled'
coh901318.c: Change initate to initiate.
mbox-db5500.c Change initate to initiate.
edac: correct i82975x error-info reported
edac: correct i82975x mci initialisation
edac: correct commented info
fs: update comments to point correct document
target: remove duplicate include of target/target_core_device.h from drivers/target/target_core_hba.c
...
Trivial conflict in fs/eventpoll.c (spelling vs addition)
* 'defcfg' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6647/1: add Versatile Express defconfig
ARM: 6644/1: mach-ux500: update the U8500 defconfig
* 'drivers' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6764/1: pl011: factor out FIFO to TTY code
ARM: 6763/1: pl011: add optional RX DMA to PL011 v2
ARM: 6758/1: amba: support pm ops
ARM: amba: make amba_driver id_table const
ARM: amba: make internal ID table handling const
ARM: amba: make probe() functions take const id tables
ARM: 6662/1: amba: make amba_bustype non-static
ARM: mmci: add dmaengine-based DMA support
ARM: mmci: no need for separate host->data_xfered
ARM: mmci: avoid unnecessary switch to data available PIO interrupts
ARM: mmci: no need to call flush_dcache_page() with sg_miter API
ARM: mmci: avoid reporting too many completed bytes on fifo overrun
ALSA: AACI: make fifo variables more explanitory
ALSA: AACI: no need to call snd_pcm_period_elapsed() for each period
ALSA: AACI: use snd_pcm_lib_period_bytes()
ALSA: AACI: clean up AACI announcement printk
ALSA: AACI: fix channel mask selection
ALSA: AACI: fix number of channels for record
ALSA: AACI: fix multiple IRQ claiming
* 'cyberpro-next' of master.kernel.org:/home/rmk/linux-2.6-arm:
VIDEO: cyberpro: remove unused cyber2000fb_get_fb_var()
VIDEO: cyberpro: remove useless function extreg pointers
VIDEO: cyberpro: update handling of device structures
VIDEO: cyberpro: add support for video capture I2C
VIDEO: cyberpro: make 'reg_b0_lock' always present
VIDEO: cyberpro: add I2C support
VIDEO: cyberpro: select lowest multipler/divisor for PLL
Replace EXTRA_CFLAGS with ccflags-y.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
The original dma_halt() function set the CA (channel abort) bit on both
the 83xx and 85xx controllers. This is incorrect on the 83xx, where this
bit means TEM (transfer error mask) instead. The 83xx doesn't support
channel abort, so we only do this operation on 85xx.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This merges the fsl_chan_ld_cleanup() function into the dma_do_tasklet()
function to reduce locking overhead. In the best case, we will be able
to keep the DMA controller busy while we are freeing used descriptors.
In all cases, the spinlock is grabbed two times fewer than before on
each transaction.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Previous to this patch, the dma_run_dependencies() function has been
called while holding desc_lock. This function can call tx_submit() for
other descriptors, which may try to re-grab the lock. Avoid this by
moving the descriptors to be cleaned up to a temporary list, and
dropping the lock before cleanup.
At the same time, add support for automatic unmapping of src and dst
buffers, as offered by the DMAEngine API.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Enabling poisoning in the dmapool API quickly showed that the DMA
controller was fetching descriptors that should not have been in use.
This has caused intermittent controller lockups during testing.
I have been unable to figure out the exact set of conditions which cause
this to happen. However, I believe it is related to the driver using the
hardware registers to track whether the controller is busy or not. The
code can incorrectly decide that the hardware is idle due to lag between
register writes and the hardware actually becoming busy.
To fix this, the driver has been reworked to explicitly track the state
of the hardware, rather than try to guess what it is doing based on the
register values.
This has passed dmatest with 10 threads per channel, 100000 iterations
per thread several times without error. Previously, this would fail
within a few seconds.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This fixes some minor violations of the coding style. It also changes
the style of the device_prep_dma_*() function definitions so they are
identical.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This adds better tracking to link descriptor allocations, callbacks, and
frees. This makes it much easier to track errors with link descriptors.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This makes debugging the driver much easier when multiple channels are
running concurrently. In addition, you can see how much descriptor
memory each channel has allocated via the dmapool API in sysfs.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This is a purely cosmetic cleanup. It is nice to have related functions
right next to each other in the code.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The dmatest code relies on the DMAEngine API to automatically call
dma_unmap_single() on src buffers. The flags it passes are incorrect,
fix them.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When CONFIG_PM=n, we get the following warning:
drivers/dma/pch_dma.c:741: warning: ‘pch_dma_suspend’ defined but not used
drivers/dma/pch_dma.c:755: warning: ‘pch_dma_resume’ defined but not used
To fix it, wrap pch_dma_{suspend,resume} and
pch_dma_{save,restore}_regs functions with CONFIG_PM.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
On ARMv7 cores, device memory mapped as Normal Non-cacheable, may not guarantee
ordered access causing failures in device drivers that do not use the mandatory
memory barriers. readl & writel versions contain necessary memory barriers for
this.
commit 79f64dbf68c8a9779a7e9a25e0a9f0217a25b57a: "ARM: 6273/1: Add barriers to
the I/O accessors if ARM_DMA_MEM_BUFFERABLE" can be referred for more
information on this.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch sets default Burst length for all transfer to 16. This will
enhance performance when user doesn't have any chan->private data.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Msize or Burst Size is peripheral dependent in case of prep_slave_sg and
cyclic_prep transfers, and in case of memcpy transfers it is platform dependent.
So msize configuration must come from platform data.
Also some peripherals (ex: JPEG), need to be flow controller for dma transfers,
so this information in case of slave_sg & cyclic_prep transfers must come from
platform data.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In Synopsys designware, channel priority is programmable. This patch adds
support for passing channel priority through platform data. By default Ascending
channel priority will be followed, i.e. channel 0 will get highest priority and
channel 7 will get lowest.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In SPEAr Platform channels 4-7 have more Fifo depth. So we must get better
channel first. This patch introduces concept of channel allocation order in
dw_dmac. If user doesn't pass anything or 0, than normal (ascending) channel
allocation will follow, else channels will be allocated in descending order.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dwc_desc_get checks all descriptors for DMA_CTRL_ACK before allocating them for
transfers. And descriptors are not marked with DMA_CRTL_ACK after transfer
finishes. Thus descriptor once used is not usable again. This patch marks
descriptors with DMA_CRTL_ACK after dma xfer finishes
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Every descriptor can transfer a maximum count of 4095 (12 bits, in control reg),
So we must have DWC_MAX_COUNT as 4095 instead of 2048.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Lock must be taken before calling dwc_scan_descriptors, as this may
access/modify shared data and queues. dwc_tx_status wasn't taking lock before
calling this routine. This patch add code that takes lock before calling
dwc_scan_descriptors.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dwc_complete_all and other routines was removing all descriptors from dwc->queue
and pushing them to dwc->active_list. Only one was required to be removed. Also
we are calling dwc_dostart, once list is fixed.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In some cases users of dw_dmac are initialized before dw_dmac, and if they try
to use dw_dmac, they simply fail. So its better we register init() routine
of driver using subsys_initcall() instead of module_init(), so that dma driver
is available at the earliest possible.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This driver will now be used in atleast two platforms AVR32 & ARM. And there is
no actual hardware dependency of this driver over AVR32 or ARM. So this
dependency can be removed altogether.
Also dw_dmac driver uses clk framework and must have compilation dependency on
HAVE_CLK
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds dma support for Freescale MXS-based SoC i.MX23/28,
including apbh-dma and apbx-dma.
* apbh-dma and apbx-dma are supported in the driver as two mxs-dma
instances.
* apbh-dma is different between mx23 and mx28, hardware version
register is used to differentiate.
* mxs-dma supports pio function besides data transfer. The driver
uses dma_data_direction DMA_NONE to identify the pio mode, and
steals sgl and sg_len to get pio words and numbers from clients.
* mxs dmaengine has some very specific features, like sense function
and the special NAND support (nand_lock, nand_wait4ready). These
are too specific to implemented in generic dmaengine driver.
* The driver refers to imx-sdma and only a single descriptor is
statically assigned to each channel.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Get rid of old users of of_platform_driver in arch/powerpc. Most
of_platform_driver users can be converted to use the platform_bus
directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make Primecell driver probe functions take a const pointer to their
ID tables. Drivers should never modify their ID tables in their
probe handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently when two or more buffers are queued by the camera driver
and so the double buffering is enabled in the idmac, we lose one
frame comming from CSI since the reporting of arrival of the first
frame is deferred by the DMAIC_7_EOF interrupt handler and reporting
of the arrival of the last frame is not done at all. So when requesting
N frames from the image sensor we actually receive N - 1 frames in
user space.
The reason for this behaviour is that the DMAIC_7_EOF interrupt
handler misleadingly assumes that the CUR_BUF flag is pointing to the
buffer used by the IDMAC. Actually it is not the case since the
CUR_BUF flag will be flipped by the FSU when the FSU is sending the
<TASK>_NEW_FRM_RDY signal when new frame data is delivered by the CSI.
When sending this singal, FSU updates the DMA_CUR_BUF and the
DMA_BUFx_RDY flags: the DMA_CUR_BUF is flipped, the DMA_BUFx_RDY
is cleared, indicating that the frame data is beeing written by
the IDMAC to the pointed buffer. DMA_BUFx_RDY is supposed to be
set to the ready state again by the MCU, when it has handled the
received data. DMAIC_7_CUR_BUF flag won't be flipped here by the
IPU, so waiting for this event in the EOF interrupt handler is wrong.
Actually there is no spurious interrupt as described in the comments,
this is the valid DMAIC_7_EOF interrupt indicating reception of the
frame from CSI.
The patch removes code that waits for flipping of the DMAIC_7_CUR_BUF
flag in the DMAIC_7_EOF interrupt handler. As the comment in the
current code denotes, this waiting doesn't help anyway. As a result
of this removal the reporting of the first arrived frame is not
deferred to the time of arrival of the next frame and the drivers
software flag 'ichan->active_buffer' is in sync with DMAIC_7_CUR_BUF
flag, so the reception of all requested frames works.
This has been verified on the hardware which is triggering the
image sensor by the programmable state machine, allowing to
obtain exact number of frames. On this hardware we do not tolerate
losing frames.
This patch also removes resetting the DMA_BUFx_RDY flags of
all channels in ipu_disable_channel() since transfers on other
DMA channels might be triggered by other running tasks and the
buffers should always be ready for data sending or reception.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
As per the reference manual, bit "L" should be set while bit "C"
should be cleared for the last buffer descriptor in the non-cyclic
chain, so that sdma can stop trying to find the next BD and end
the transfer.
In case of sdma_prep_slave_sg(), BD_LAST needs to be set and BD_CONT
be cleared for the last BD.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
sdma_handle_channel_loop() is the handler of cyclic tx. One period
success does not really mean the success of the tx. Instead of
DMA_SUCCESS, DMA_IN_PROGRESS should be the one to tell.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The sdmac->status was designed to reflect the status of the tx,
so simply return it in sdma_tx_status(). Then dma client can call
dma_async_is_tx_complete() to know the status of the tx.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
sdma_prep_dma_cyclic() sets sdmac->status to DMA_ERROR in err_out,
and sdma_prep_slave_sg() needs to do the same. Otherwise,
sdmac->status stays at DMA_IN_PROGRESS, which will make the function
return immediately next time it gets called.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is a leftover from the time that the driver did not have
sdma_prep_dma_cyclic callback and implemented sound dma as a looped
sg chain. And it can be removed now.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We need channel 0 of the sdma engine for internal purposes. We
accomplished this by calling dma_request_channel() in the probe
function. This does not work when multiple dma engines are
present which is the case when IPU support for i.MX31/35 is
compiled in. So instead of registering channel 0 and reserving
it afterwards simply do not register it in the first place.
With this the dmaengine channel counting does not match sdma
channel counting anymore, so we have to use sdma channel counting
in the driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch lets sdma_prep_slave_sg fail if the entries of an
sg list do not start on multiples of the word size or if the
lengths are not multiple of the word size.
Also, catch the previously unhandled DMA_SLAVE_BUSWIDTH_8_BYTES
and DMA_SLAVE_BUSWIDTH_UNDEFINED cases.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Support cyclic transfers, which are useful for ALSA drivers.
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The current implementation of DMA_TERMINATE_ALL leaves ongoing transfers
running. Fix it.
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The DMA_SG cap is enabled on the wrong channel, and the pointers are repeatedly
set incorrectly. Fix it and combine the ops settings to a common function.
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
These register writes are better placed in the main source file rather than
ll.c.
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The dmaengine framework has the API for this now.
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The desc init code can be shared between the mem and slave prep routines.
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
To simplify the code.
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Map and unmap the LLIs and use dma_sync_single_for_device() appropriately
instead of mapping and never unmapping them.
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Map the buffer once and use dma_sync*() appropriately instead of mapping the
buffer over and over without unmapping it.
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The address to use for DMA should be taken from sg_dma_address() and not
sg_phys().
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
ALIGN(x * y, y) == x * y
ALIGN(aligned + x * y, y) == aligned + x * y
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
DB8500v2's DMA40 (revision 3) allows setting event lines as high priority and
real time.
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
And add DB8500v2 information.
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Almost every use of dev_err in this driver prints the function name. Abstract
out wrappers to help with this and reduce code duplication.
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The somewhat confusing check
d40c->log_num == D40_PHY_CHAN
and its variants are used in several places to check if a channel is logical or
physical. Use appropriately named helpers to do this to make the code more
readable.
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The register offset computation for accessing channel registers is copy/pasted
in several places. Create a helper function to do it.
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This link in hardware with previous jobs code is:
- unused, no clients using or requiring this feature
- incomplete, being implemented only for physical channels
- broken, only working to perform one link
Remove it. This also allows us to get rid of the channel pause in the
submit_tx() routine.
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The controller sometimes fails to register the enable of the event line when
both src and dst event lines are used on the same logical channel. Implement
the recommended software workaround, which is to retry the write until it
works.
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If a transfer is initiated from memory to a peripheral, then data is
fetched and the channel is marked busy. This busy status persists until
the HALT bit is set and the queued data has been transfered to the
peripheral. Waiting indefinitely after setting the HALT bit results in
system lockups. Timeout this operation, and print an error when this
happens.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If we try to pause a channel when terminating a transfer, we could end
up spinning for it to become inactive indefinitely, and can result in
an uninterruptible wait requiring a reset to recover from.
Terminating a transfer is supposed to take effect immediately, but may
result in data loss.
To make this clear, rename the function to pl08x_terminate_phy_chan().
Also, make sure it is always consistently called - with the spinlock
held and IRQs disabled, and ensure that the TC and ERR interrupt status
is always cleared.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Some platforms (e.g. Picochip PC3XX) have multiple DMA controllers
where some may be used for slave transfers and others for general
purpose memcpy type transfers. Add a .is_private boolean to the
platform data structure so that controllers can be marked as private
so that the DMA_PRIVATE capability will be set for that controller.
Signed-off-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Some platforms have flexible mastering capabilities and this needs
to be selected at runtime. If the platform has specified private
data in the form of the dw_dma_slave then fetch the source and
destination masters from here. If this isn't present, default to
the previous of 0 and 1.
v2: cleanup whitespace
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Viresh Kumar