regChainOffset is always zero, remove it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add eeprom_def.c, eeprom_4k.c and eeprom_9287.c
This improves maintainability.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With iwconfig there is no way to properly set the ciphers when trying to
connect to a WEP SSID. Although mac80211 based drivers dont need it, several
fullmac drivers do.
This patch basically sets the WEP ciphers whenever they're not set at all.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an AP disassociates us, we currently go into a weird
state because the SME doesn't handle authenticated but not
associated well unless it's within its own state machine,
it can't recover from that. However, it shouldn't need to,
since we don't do any decisions in it really -- so when we
get disconnected, simply deauthenticate too.
Reported-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When reporting a disconnection to userspace, we try
to report whether it was from the AP or by our own
choice. However, we misreported a broadcast deauth
or disassoc as being by own choice, which is wrong.
Fix this by checking the sender address instead of
the destination address.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After being disassociated by the AP, mac80211 currently
reports this to cfg80211, and then goes to delete the
association. That's fine, but cfg80211 assumes that it's
still authenticated, however, mac80211 throws away all
state.
This fixes mac80211 to keep track of the authentication
in that case so that cfg80211 can request a deauth or
new association properly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for the wl1271 driver in the Kconfig and in the
Makefile.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This driver supports the wl1271 chipset from Texas Instruments based on the
WiLink(tm) 6.0 mobile platform. Support for wl1273 should be relatively easy
to add. This chipset is designed for embedded devices, with good powersaving
capabilities. The wl1271 chipset is the successor of wl1251 and supports the
802.11b/g/n standards, but currently this driver supports only b/g.
More information about this chipset can be found here:
http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?templateId=6123&navigationId=12762&contentId=29993
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WARN_ON was triggered at mlme.c:213 when dissociating from an AP.
wdev->current_bss->pub.bssid should be used in place of
wdev->current_bss for BSSID comparison.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When TKIP support was added, we stored the keys separately to avoid
issues when both TKIP and WEP keys are sent to the driver.
We need to consolidate the storage to convert to cfg80211, so do this
first and try iron out the issues.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We will need this from the cfg80211 disassociate call.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows the disassociation to be called via cfg80211.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we store the keys for cfg80211, the sequence lengths will also be
stored. So avoid assuming the sequence lengths at this level.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helps in the refactorring required to convert the driver to
cfg80211.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a boolean value set based on firmware capabilities, so move the
variable to the capabilities section and reduce the structure size.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211 displays correct link info when connected by wext. But if
the connection is setup by cfg80211, wext cannot display the SSID.
This patch fixed this issue.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update a comment that still says IEEE80211_IF_TYPE instead of NL80211_IFTYPE.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tkip hw support uncovered a bug in b43_write_probe_resp_template : it is
writing at the wrong shm offset, it is in the B43_SHM_SH_TKIPTSCTTAK
zone. Remove b43_write_probe_resp_template, b43_write_probe_resp_plcp
and b43_write_probe_resp_plcp because the probe response offload is
currently not supported by mac80211.
Signed-off-by: Gregor Kowski <gregor.kowski@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make use of HostFlags defines in the LP-PHY code.
Fix fallout from the IEEE80211_IF_TYPE to NL80211_IFTYPE change.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh is currently disabled on mac80211, its marked
as broken. This patch gets it to compile though,
to account for the mac80211 workqueue changes.
There was a simple typo in the patches for mesh
for the workqueue migration, but we never compile
tested it as we couldn't even select mesh as its
broken. Lets at least let it compile for those
interested in getting it fixed.
Reported-by: Pat Erley <pat-lkml@erley.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add B2063 radio init code and tables for LP-PHY.
Rename structures common between B2062 and B2063 to B206X.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd1211rw uses its own LED stuff so let rename its LED
stuff as such.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We used to set pspoll filter on ath9k on AP mode but
we no longer need this mode specific check as mac80211
now does the check for us and informs us when we should
enable pspoll through FIF_PSPOLL.
Cc: Igor Perminov <igor.perminov@inbox.ru>
Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let ath5k_chan_set() always call ath5k_reset().
This fixes the bug that we don't
get any packets in monitor mode after:
ifconfig wlan0 down
iwconfig wlan0 mode monitor channel 1
ifconfig wlan0 up
but they arrive after
iwconfig wlan0 channel 2
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change rt2x00_rf_read() and rt2x00_rf_write() to subtract 1 from the rf
register number. This is needed because the rf registers are enumerated
starting with one. The size of the rf register cache is just enough to
hold all registers, so writing to the highest register was corrupting
memory. Add a check to make sure that the rf register number is valid.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Cc: stable@kernel.org
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Traffic received with a priority tag (VID = 0) and non-zero priority value was
incorrectly handled by the VLAN packet code path due to a check on zero for
the whole VLAN tag instead of just the VID.
This patch masked out the priority field when checking the vlan tag for
received VLAN packets.
Signed-off-by: Lucy Liu <lucy.liu@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We return the ddp->len in ixgbe_fcoe_ddp() to indicate the length of data that
have been DDPed. However, it is possible that the length is 0, e.g., for SCSI
READ, the FCP_RSP may come back w/ SCSI status 0x28 as Task Set Full with no FCP
data for DDP. In ixgbe_fcoe_ddp(), we return 0 to indicate not passing DDPed
packets to upper layer. Therefore in the case of ddp->len being 0 upon FCP_RSP,
we do not want to return the 0 ddp->len as we want FCP_RSP to be always
delivered to the upper layer. This patch fixes this bug by setting rc only if
ddp->len is non-zero.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I did not introduce new lines over 80 chars. I even eliminated some of
them.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses:
* assigning -1 to np->tclass as it is currently done is not very meaningful,
since it turns into 0xff;
* RFC 3542, 6.5 allows -1 for clearing the sticky IPV6_TCLASS option
and specifies -1 to mean "use kernel default":
- RFC 2460, 7. requires that the default traffic class must be zero for
all 8 bits,
- this is consistent with RFC 2474, 4.1 which recommends a default PHB of 0,
in combination with a value of the ECN field of "non-ECT" (RFC 3168, 5.).
This patch changes the meaning of -1 from assigning 255 to mean the RFC 2460
default, which at the same time allows to satisfy clearing the sticky TCLASS
option as per RFC 3542, 6.5.
(When passing -1 as ancillary data, the fallback remains np->tclass, which
has either been set via socket options, or contains the default value.)
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This replaces assignments of the type "int on LHS" = "u8 on RHS" with
simpler code. The LHS can express all of the unsigned right hand side
values, hence the assigned value can not be negative.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb allocation / consumption correlator
Add ftracer module to kernel to print out a list that correlates a process id,
an skb it read, and the numa nodes on wich the process was running when it was
read along with the numa node the skbuff was allocated on.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Makefile | 1
trace.h | 19 ++++++
trace_skb_sources.c | 154 ++++++++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 174 insertions(+)
Signed-off-by: David S. Miller <davem@davemloft.net>
skb allocation / consumption corelator - Add config option
This patch adds a Kconfig option to enable the addtition of the skb source
tracer.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Kconfig | 10 ++++++++++
1 file changed, 10 insertions(+)
Signed-off-by: David S. Miller <davem@davemloft.net>
o Defer napi resouce allocation to device attach.
o Free napi resources and delete napi during detach.
This ensures right behavior across firmware reset.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Remove private workqueue in the driver, move all
scheduled tasks to keventd workqueues. This makes
ports (interfaces) of same / different NIC boards
independent, in terms of their link watchdog and
reset tasks.
o Move quick checks for link status and temperature
in timer callback, schedule watchdog task only if
link status changed or temperature reached critical
threshold.
This also fixes deadlock when thermal panic occurs,
watchdog work was flushing workqueue that it was
sitting on.
Signed-off-by: Amit Kumar Salecha <amit@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently setting rx-usecs when the interface is in legacy interrupt
mode it is not immediate. We were only setting EITR for each MSIx
vector and since this count would be zero for legacy mode it wasn't
set until after a reset. This patch corrects that by checking what
mode we are in and then setting EITR accordingly.
Signed-off-by: Don Skidmore <donald.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For 'real' hardware CAN devices the netlink interface is used to set CAN
specific communication parameters. Real CAN hardware can not be created with
the ip tool ...
The invocation of 'ip link add type can' lead to an oops as the standard rtnl
newlink function was called:
http://bugzilla.kernel.org/show_bug.cgi?id=13954
This patch adds a private newlink function for the CAN device driver interface
that unconditionally returns -EOPNOTSUPP.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Reported-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
CC: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb allocation / cosumption tracer - Add consumption tracepoint
This patch adds a tracepoint to skb_copy_datagram_iovec, which is called each
time a userspace process copies a frame from a socket receive queue to a user
space buffer. It allows us to hook in and examine each sk_buff that the system
receives on a per-socket bases, and can be use to compile a list of which skb's
were received by which processes.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
include/trace/events/skb.h | 20 ++++++++++++++++++++
net/core/datagram.c | 3 +++
2 files changed, 23 insertions(+)
Signed-off-by: David S. Miller <davem@davemloft.net>
I fixed up my mac driver, which relatives to previous
mac driver actually in the tree.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also avoids a potential buffer overflow in case the very first
receive descriptor fails to allocate, as an index of -1 would be used
afterwards. Kudos to Roel Kluin for pointing this out and providing an
initial patch.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro DRV_NAME contains "korina", the field dev->name points to the
actual interface name. So messages were formerly prefixed with
'korinaeth2:' (on my system).
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a 'hairpin' (also called 'reflective relay') mode
port configuration to the Linux Ethernet bridge kernel module.
A bridge supporting hairpin forwarding mode can send frames back
out through the port the frame was received on.
Hairpin mode is required to support basic VEPA (Virtual
Ethernet Port Aggregator) capabilities.
You can find additional information on VEPA here:
http://tech.groups.yahoo.com/group/evb/http://www.ieee802.org/1/files/public/docs2009/new-hudson-vepa_seminar-20090514d.pdfhttp://www.internet2.edu/presentations/jt2009jul/20090719-congdon.pdf
An additional patch 'bridge-utils: Add 'hairpin' port forwarding mode'
is provided to allow configuring hairpin mode from userspace tools.
Signed-off-by: Paul Congdon <paul.congdon@hp.com>
Signed-off-by: Anna Fischer <anna.fischer@hp.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If dev_alloc_skb() fails on the first iteration of the allocation loop,
then we end up writing before the start of the array.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an interface has multiple addresses, the current message for DAD
failure isn't really helpful, so this patch adds the address itself to
the printk.
Signed-off-by: Jens Rosenboom <jens@mcbone.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We splice skbs from the pending queue for a TID
onto the local pending queue when tearing down a
block ack request. This is not necessary unless we
actually have received a request to start a block ack
request (rate control, for example). If we never received
that request we should not be splicing the tid pending
queue as it would be null, causing a panic.
Not sure yet how exactly we allowed through a call when the
tid state does not have at least HT_ADDBA_REQUESTED_MSK set,
that will require some further review as it is not quite
obvious.
For more information see the bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=13922
This fixes this oops:
BUG: unable to handle kernel NULL pointer dereference at 00000030
IP: [<f8806c70>] ieee80211_agg_splice_packets+0x40/0xc0 [mac80211]
*pdpt = 0000000002d1e001 *pde = 0000000000000000
Thread overran stack, or stack corrupted
Oops: 0000 [#1] SMP
last sysfs file: /sys/module/aes_generic/initstate
Modules linked in: <bleh>
Pid: 0, comm: swapper Not tainted (2.6.31-rc5-wl #2) Dell DV051
EIP: 0060:[<f8806c70>] EFLAGS: 00010292 CPU: 0
EIP is at ieee80211_agg_splice_packets+0x40/0xc0 [mac80211]
EAX: 00000030 EBX: 0000004c ECX: 00000003 EDX: 00000000
ESI: c1c98000 EDI: f745a1c0 EBP: c076be58 ESP: c076be38
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
Process swapper (pid: 0, ti=c076a000 task=c0709160 task.ti=c076a000)
Stack: <bleh2>
Call Trace:
[<f8806edb>] ? ieee80211_stop_tx_ba_cb+0xab/0x150 [mac80211]
[<f8802f1e>] ? ieee80211_tasklet_handler+0xce/0x110 [mac80211]
[<c04862ff>] ? net_rx_action+0xef/0x1d0
[<c0149378>] ? tasklet_action+0x58/0xc0
[<c014a0f2>] ? __do_softirq+0xc2/0x190
[<c018eb48>] ? handle_IRQ_event+0x58/0x140
[<c01205fe>] ? ack_apic_level+0x7e/0x270
[<c014a1fd>] ? do_softirq+0x3d/0x40
[<c014a345>] ? irq_exit+0x65/0x90
[<c010a6af>] ? do_IRQ+0x4f/0xc0
[<c014a35d>] ? irq_exit+0x7d/0x90
[<c011d547>] ? smp_apic_timer_interrupt+0x57/0x90
[<c01094a9>] ? common_interrupt+0x29/0x30
[<c010fd9e>] ? mwait_idle+0xbe/0x100
[<c0107e42>] ? cpu_idle+0x52/0x90
[<c054b1a5>] ? rest_init+0x55/0x60
[<c077492d>] ? start_kernel+0x315/0x37d
[<c07743ce>] ? unknown_bootoption+0x0/0x1f9
[<c0774099>] ? i386_start_kernel+0x79/0x81
Code: <bleh3>
EIP: [<f8806c70>] ieee80211_agg_splice_packets+0x40/0xc0 [mac80211] SS:ESP 0068:c076be38
CR2: 0000000000000030
Cc: stable@kernel.org
Testedy-by: Jack Lau <jackelectronics@hotmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith