Manish Chopra says:
====================
qed*: Bug fixes.
This series contains general qed/qede fixes.
Please consider applying this to "net"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Version update for qed/qede modules.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix unnecessary logging of message in an expected
default case where coalescing value read (via ethtool -c)
migh not be valid unless they are configured explicitly
in the hardware using ethtool -C.
Signed-off-by: Rahul Verma <rverma@marvell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under heavy traffic load, when changing number of channels via
ethtool (ethtool -L) which will cause interface to be reloaded,
it was observed that some packets gets transmitted on old TX
channel/queue id which doesn't really exist after the channel
configuration leads to system crash.
Add a safeguard in the driver by validating queue id through
ndo_select_queue() which is called before the ndo_start_xmit().
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Max supported queues is derived incorrectly in the case of multi-CoS.
Need to consider TCs while calculating num_queues for PF.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of Unified Fabric Port (UFP) mode, switch provides
the traffic class (TC) value to be used for the traffic.
Configure hardware to use this TC value for vlan priority.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When slowpath messages are sent with high rate, the resulting
events can lead to a FW assert in case they are not handled fast
enough (Event Queue Full assert). Attempt to send queued slowpath
messages only after the newly evacuated entries in the EQ ring
are indicated to FW.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A patch set from Christoph for vmwgfx dma mode detection breakage with the
new dma code restructuring in 5.0
A couple of fixes also CC'd stable
Finally an improved IOMMU detection that automatically enables dma mapping
also with other vIOMMUS than the intel one if present and enabled.
Currently trying to start a VM in that case would fail catastrophically.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Hellstrom <thellstrom@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190206194735.4663-1-thellstrom@vmware.com
bio_trim() has an early return, which makes it _not_ idempotent, if the
offset is 0 and the bio's bi_size already matches the requested size.
Prior to DM, all users of bio_trim() were fine with this. But DM has
exposed the fact that bio_trim()'s early return is incompatible with a
cloned bio whose integrity payload must be trimmed via
bio_integrity_trim().
Fix this by reverting DM back to doing the equivalent of bio_trim() but
in an idempotent manner (so bio_integrity_trim is always performed).
Follow-on work is needed to assess what benefit bio_trim()'s early
return is providing to its existing callers.
Reported-by: Milan Broz <gmazyland@gmail.com>
Fixes: 57c36519e4 ("dm: fix clone_bio() to trigger blk_recount_segments()")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Block core changes to switch bio-based IO accounting to be percpu had a
side-effect of altering DM core to now rely on calling waitqueue_active
(in both bio-based and request-based) to check if another task is in
dm_wait_for_completion().
A memory barrier is needed before calling waitqueue_active(). DM core
doesn't piggyback on a preceding memory barrier so it must explicitly
use its own.
For more details on why using waitqueue_active() without a preceding
barrier is unsafe, please see the comment before the waitqueue_active()
definition in include/linux/wait.h.
Add the missing memory barrier by switching to using wq_has_sleeper().
Fixes: 6f75723190 ("dm: remove the pending IO accounting")
Fixes: c4576aed8d ("dm: fix request-based dm's use of dm_wait_for_completion")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Ido Schimmel says:
====================
mlxsw: Offload blackhole routes
Blackhole routes are routes that cause matching packets to be silently
dropped. This is in contrast to unreachable routes that generate an ICMP
host unreachable packet in response.
The driver currently programs both route types with a trap action and
lets the kernel drop matching packets. This is sub-optimal as packets
routed using a blackhole route can be directly dropped by the ASIC.
Patch #1 alters mlxsw to program blackhole routes with a discard action.
Patch #2 adds a matching test.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a simple topology consisting of two hosts directly connected to a
router. Make sure IPv4/IPv6 ping works and then add blackhole routes.
Test that ping fails and that the routes are marked as offloaded. Use a
simple tc filter to test that packets were dropped by the ASIC and not
trapped to the CPU.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new FIB entry type for blackhole routes and set it in case the
type of the notified route is 'RTN_BLACKHOLE'.
Program such routes with a discard action and mark them as offloaded
since the device is dropping the packets instead of the kernel.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: Introduce ndo_get_port_parent_id()
Based on discussion with Ido and feedback from Jakub there are clearly
two classes of users that implement SWITCHDEV_ATTR_ID_PORT_PARENT_ID:
- PF/VF drivers which typically only implement return the port's parent
ID, yet have to implement switchdev_port_attr_get() just for that
- Ethernet switch drivers: mlxsw, ocelot, DSA, etc. which implement more
attributes which we want to be able to eventually veto in the context
of the caller, thus making them candidates for using a blocking notifier
chain
Changes in v4:
- remove superfluous net/switchdev.h inclusions in a few files
- added Jiri's Acked-by where given
- removed err = -EOPNOTSUPP initializations
- changed according to Jiri's suggestion in net/ipv4/ipmr.c
Changes in v3:
- keep ethsw's switchdev_ops assignment
- remove inclusion of net/switchdev.h in netdevsim which is no longer
necesary
Changes in v2:
- resolved build failures spotted by kbuild test robot
- added helpers functions into the core network device layer:
dev_get_port_parent_id() and netdev_port_same_parent_id();
- added support for recursion to lower devices
Changes from RFC:
- introduce a ndo_get_port_parent_id() and convert all relevant drivers
to use it
- get rid of SWITCHDEV_ATTR_ID_PORT_PARENT_ID
A subsequent set of patches will convert switchdev_port_attr_set() to
use a blocking notifier call, and still get rid of
switchdev_port_attr_get() altogether.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a dedicated NDO for getting a port's parent ID, get rid
of SWITCHDEV_ATTR_ID_PORT_PARENT_ID and convert all callers to use the
NDO exclusively. This is a preliminary change to getting rid of
switchdev_ops eventually.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA implements SWITCHDEV_ATTR_ID_PORT_PARENT_ID and we want to get rid
of switchdev_ops eventually, ease that migration by implementing a
ndo_get_port_parent_id() function which returns what
switchdev_port_attr_get() would do.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethsw implements SWITCHDEV_ATTR_ID_PORT_PARENT_ID and we want to get rid
of switchdev_ops eventually, ease that migration by implementing a
ndo_get_port_parent_id() function which returns what
switchdev_port_attr_get() would do.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdevsim only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID, which makes it a
great candidate to be converted to use the ndo_get_port_parent_id() NDO
instead of implementing switchdev_port_attr_get().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw implements SWITCHDEV_ATTR_ID_PORT_PARENT_ID and we want to get rid
of switchdev_ops eventually, ease that migration by implementing a
ndo_get_port_parent_id() function which returns what
switchdev_port_attr_get() would do.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID, which makes it a
great candidate to be converted to use the ndo_get_port_parent_id() NDO
instead of implementing switchdev_port_attr_get().
Since NFP uses switchdev_port_same_parent_id() convert it to use
netdev_port_same_parent_id().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ocelot only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID as a valid
switchdev attribute getter, convert it to use ndo_get_port_parent_id()
and get rid of the switchdev_ops::switchdev_port_attr_get altogether.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw implements SWITCHDEV_ATTR_ID_PORT_PARENT_ID and we want to get rid
of switchdev_ops eventually, ease that migration by implementing a
ndo_get_port_parent_id() function which returns what
switchdev_port_attr_get() would do.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5e only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID, which makes it a
great candidate to be converted to use the ndo_get_port_parent_id() NDO
instead of implementing switchdev_port_attr_get().
Since mlx5e makes use of switchdev_port_parent_id() convert it to use
netdev_port_same_parent_id().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Liquidio only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID, which makes it
a great candidate to be converted to use the ndo_get_port_parent_id()
NDO instead of implementing switchdev_port_attr_get().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BNXT only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID, which makes it a
great candidate to be converted to use the ndo_get_port_parent_id() NDO
instead of implementing switchdev_port_attr_get(). The conversion is
straight forward here since the PF and VF code use the same getter.
Since bnxt makes uses of switchdev_port_same_parent_id() convert it to
use netdev_port_same_parent_id().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for getting rid of switchdev_ops, create a dedicated NDO
operation for getting the port's parent identifier. There are
essentially two classes of drivers that need to implement getting the
port's parent ID which are VF/PF drivers with a built-in switch, and
pure switchdev drivers such as mlxsw, ocelot, dsa etc.
We introduce a helper function: dev_get_port_parent_id() which supports
recursion into the lower devices to obtain the first port's parent ID.
Convert the bridge, core and ipv4 multicast routing code to check for
such ndo_get_port_parent_id() and call the helper function when valid
before falling back to switchdev_port_attr_get(). This will allow us to
convert all relevant drivers in one go instead of having to implement
both switchdev_port_attr_get() and ndo_get_port_parent_id() operations,
then get rid of switchdev_port_attr_get().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function can't succeed if dp->pl is NULL. It will Oops inside the
call to return phylink_ethtool_get_eee(dp->pl, e);
Fixes: 1be52e97ed ("dsa: slave: eee: Allow ports to use phylink")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change t4fw_version.h to update latest firmware version
number to 1.22.9.0.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read MAC address 32-bit at a time and manually extract the individual
bytes. This avoids pointer aliasing and gives the compiler a better
chance of optimizing the operation.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the system was booted using a device tree and if the device tree
contains a MAC address, use it instead of reading one from the EEPROM.
This is useful in situations where the EEPROM isn't properly programmed
or where the firmware wants to override the existing MAC address.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two and a half years ago, the client was changed to use gathered
Send for larger inline messages, in commit 655fec6987 ("xprtrdma:
Use gathered Send for large inline messages"). Several fixes were
required because there are a few in-kernel device drivers whose
max_sge is 3, and these were broken by the change.
Apparently my memory is going, because some time later, I submitted
commit 25fd86eca1 ("svcrdma: Don't overrun the SGE array in
svc_rdma_send_ctxt"), and after that, commit f3c1fd0ee2 ("svcrdma:
Reduce max_send_sges"). These too incorrectly assumed in-kernel
device drivers would have more than a few Send SGEs available.
The fix for the server side is not the same. This is because the
fundamental problem on the server is that, whether or not the client
has provisioned a chunk for the RPC reply, the server must squeeze
even the most complex RPC replies into a single RDMA Send. Failing
in the send path because of Send SGE exhaustion should never be an
option.
Therefore, instead of failing when the send path runs out of SGEs,
switch to using a bounce buffer mechanism to handle RPC replies that
are too complex for the device to send directly. That allows us to
remove the max_sge check to enable drivers with small max_sge to
work again.
Reported-by: Don Dutile <ddutile@redhat.com>
Fixes: 25fd86eca1 ("svcrdma: Don't overrun the SGE array in ...")
Cc: stable@vger.kernel.org
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
If the parameter 'count' is non-zero, nfsd4_clone_file_range() will
currently clobber all errors returned by vfs_clone_file_range() and
replace them with EINVAL.
Fixes: 42ec3d4c02 ("vfs: make remap_file_range functions take and...")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: stable@vger.kernel.org # v4.20+
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Add maintainer entry for SFF/SFP/SFP+ support.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: core: Trace EMAD errors
Nir says:
This patchset adds a trace for EMAD errors to the existing EMAD payload
traces. This tracepoint is useful to track user or firmware errors during
tests execution.
Patch #1 defines the devlink tracepoint.
Patch #2 uses it for reporting mlxsw EMAD errors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Trace EMAD errors returned from HW.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define a tracepoint and allow user to trace messages in case of an hardware
error code for hardware associated with devlink instance.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciocoi Radulescu says:
====================
dpaa2-eth: Driver updates
First patch moves the driver to a page-per-frame memory model.
The others are minor tweaks and optimizations.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add more buffers to the Rx buffer pool as soon as 7 of them
get consumed, instead of waiting for their number to drop
below a fixed threshold.
7 is the number of buffers that can be released in the pool
via a single DPIO command.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with MC10.14.0, dpaa2_io_service_enqueue_fq() API is
functional. Since there are a number of cases where it offers
better performance compared to the currently used enqueue
function, switch to it for firmware versions that support it.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While in NAPI context, free skbs by calling napi_consume_skb()
instead of dev_kfree_skb(), to take advantage of the bulk freeing
mechanism.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of allocating page fragments via the network stack,
use the page allocator directly. For now, we consume one page
for each Rx buffer.
With the new memory model we are free to consider adding more
XDP support.
Performance decreases slightly in some IP forwarding cases.
No visible effect on termination traffic. The driver memory
footprint increases as a result of this change, but it is
still small enough to not really matter.
Another side effect is that now Rx buffer alignment requirements
are naturally satisfied without any additional actions needed.
Remove alignment related code, except in the buffer layout
information conveyed to MC, as hardware still needs to know the
alignment value we guarantee.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
add flow_rule infrastructure
This patchset, as is, allows us to reuse the driver codebase to
configure ACL hardware offloads for the ethtool_rxnfc and the TC flower
interfaces. A few clients for this infrastructure are presented, such as
the bcm_sf2 and the qede drivers, for reference. Moreover all of the
existing drivers in the tree are converted to use this infrastructure.
This patchset is re-using the existing flow dissector infrastructure
that was introduced by Jiri Pirko et al. so the amount of abstractions
that this patchset adds are minimal. Well, just a few wrapper structures
for the selector side of the rules. And, in order to express actions,
this patchset exposes an action API that is based on the existing TC
action infrastructure and what existing drivers already support on that
front.
v7: This patchset is a rebase on top of the net-next tree, after
addressing questions and feedback from driver developers in the
last batch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The qede driver supports for ethtool_rx_flow_spec and flower, both
codebases look very similar.
This patch uses the ethtool_rx_flow_rule() infrastructure to remove the
duplicated ethtool_rx_flow_spec parser and consolidate ACL offload
support around the flow_rule infrastructure.
Furthermore, more code can be consolidated by merging
qede_add_cls_rule() and qede_add_tc_flower_fltr(), these two functions
also look very similar.
This driver currently provides simple ACL support, such as 5-tuple
matching, drop policy and queue to CPU.
Drivers that support more features can benefit from this infrastructure
to save even more redundant codebase.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a preparation patch to reuse the existing TC flower codebase
from ethtool_rx_flow_spec.
This patch is merely moving the core ethtool_rx_flow_spec parser after
tc flower offload driver code so we can skip a few forward function
declarations in the follow up patch.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update this driver to use the flow_rule infrastructure, hence we can use
the same code to populate hardware IR from ethtool_rx_flow and the
cls_flower interfaces.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a function to translate the ethtool_rx_flow_spec
structure to the flow_rule representation.
This allows us to reuse code from the driver side given that both flower
and ethtool_rx_flow interfaces use the same representation.
This patch also includes support for the flow type flags FLOW_EXT,
FLOW_MAC_EXT and FLOW_RSS.
The ethtool_rx_flow_spec_input wrapper structure is used to convey the
rss_context field, that is away from the ethtool_rx_flow_spec structure,
and the ethtool_rx_flow_spec structure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These actions need to be added to support the ethtool_rx_flow interface.
The queue action includes a field to specify the RSS context, that is
set via FLOW_RSS flow type flag and the rss_context field in struct
ethtool_rxnfc, plus the corresponding queue index. FLOW_RSS implies that
rss_context is non-zero, therefore, queue.ctx == 0 means that FLOW_RSS
was not set. Also add a field to store the vf index which is stored in
the ethtool_rxnfc ring_cookie field.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller