ath_get_mac80211_qnum() expects the queue 'subtype'
(internal ID for the WMM AC) as argument when looking up
the mac80211 queue, however ath_wake_mac80211_queue provides
txq->axq_qnum instead, which contains the hardware queue
number. Fix this by keeping track of the WMM class ID in
the txq data structure.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All AR9003 devices are PCI-E only, the extra delay here
is not required and only reduces the delay for loading
the initial register values by at least 14ms.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9003 has been tested with the new ANI implementation
and so ANI can now be enabled for that family.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for ANI for AR9003. The implementation for
ANI for AR9003 is slightly different than the one used for
the older chipset families. It can technically be used for
the older families as well but this is not yet fully tested
so we only enable the new ANI for the AR5008, AR9001 and AR9002
families with a module parameter, force_new_ani.
The old ANI implementation is left intact.
Details of the new ANI implemention:
* ANI adjustment logic is now table driven so that each ANI level
setting is parameterized. This makes adjustments much more
deterministic than the old procedure based logic and allows
adjustments to be made incrementally to several parameters per
level.
* ANI register settings are now relative to INI values; so ANI
param zero level == INI value. Appropriate floor and ceiling
values are obeyed when adjustments are combined with INI values.
* ANI processing is done once per second rather that every 100ms.
The poll interval is now a set upon hardware initialization and
can be picked up by the core driver.
* OFDM error and CCK error processing are made in a round robin
fashion rather than allowing all OFDM adjustments to be made
before CCK adjustments.
* ANI adjusts MRC CCK off in the presence of high CCK errors
* When adjusting spur immunity (SI) and OFDM weak signal detection,
ANI now sets register values for the extension channel too
* When adjusting FIR step (ST), ANI now sets register for FIR step
low too
* FIR step adjustments now allow for an extra level of immunity for
extremely noisy environments
* The old Noise immunity setting (NI), which changes coarse low, size
desired, etc have been removed. Changing these settings could affect
up RIFS RX as well.
* CCK weak signal adjustment is no longer used
* ANI no longer enables phy error interrupts; in all cases phy hw
counting registers are used instead
* The phy error count (overflow) interrupts are also no longer used
for ANI adjustments. All ANI adjustments are made via the polling
routine and no adjustments are possible in the ISR context anymore
* A history settings buffer is now correctly used for each channel;
channel settings are initialized with the defaults but later
changes are restored when returning back to that channel
* When scanning, ANI is disabled settings are returned to (INI) defaults.
* OFDM phy error thresholds are now 400 & 1000 (errors/second units) for
low/high water marks, providing increased stability/hysteresis when
changing levels.
* Similarly CCK phy error thresholds are now 300 & 600 (errors/second)
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new ANI implementation will use this to skip ANI
calibration upon a scan. This cannot be ported to the
older ANI implementation unless default ANI values from
the ANI are also used upon a scan. This is essentially
what one of the things thenew ANI does.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9003 hardware family will use a slightly modified ANI
implementation which has not yet been tested on the other hardware
families. To allow for this new ANI implementation a few ANI
calls need to be abstracted away. This patch just allows for
each hardware family to declare their own ANI ops and annotates
the current ANI implementation as old.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We get an MIB interrupt when we hit certain PHY error counter
thresholds. If ANI is disabled but the MIB interrupt is enabled
we'll keep around the old MIB interrupt causes.
Since ath9k disables the MIB interrupt when ANI is disabled
this is not a fix, but more of a sanity fix in case we ever
need the MIB interrupt enabled but disabling ANI.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The clock rate was assumed to be static but it actually
changes depending on the mode of operation, correct this
to help improve the calcuation of the listenTime for ANI.
This change will help adjust ANI more accurately on different
PHY thresholds.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These will be used by the ANI code next.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow drivers to sleep, and indicate this in
the documentation. ath9k has some locking I
don't understand, so keep it safe and disable
BHs in it, all other drivers look fine with
the context change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The non-irqsafe aggregation start/stop done
callbacks are currently only used by ath9k_htc,
and can cause callbacks into the driver again.
This might lead to locking issues, which will
only get worse as we modify locking. To avoid
trouble, remove the non-irqsafe versions and
change ath9k_htc to use those instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes 'make -j24 CONFIG_DEBUG_SECTION_MISMATCH=y' warning:
drivers/net/wireless/ath/ath9k/eeprom_4k.c: In function ‘ath9k_hw_get_4k_gain_boundaries_pdadcs.clone.1’:
drivers/net/wireless/ath/ath9k/eeprom_4k.c:311: error: ‘minPwrT4’ may be used uninitialized in this function
drivers/net/wireless/ath/ath9k/eeprom_9287.c: In function ‘ath9k_hw_get_AR9287_gain_boundaries_pdadcs’:
drivers/net/wireless/ath/ath9k/eeprom_9287.c:302: error: ‘minPwrT4’ may be used uninitialized in this function
drivers/net/wireless/ath/ath9k/eeprom_def.c: In function ‘ath9k_hw_get_def_gain_boundaries_pdadcs.clone.0’:
drivers/net/wireless/ath/ath9k/eeprom_def.c:679: error: ‘minPwrT4’ may be used uninitialized in this function
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The following commit added an entry in 11na and 11ng rate
table but missed to update its rate count field. This
inconsistency between the rate count and the actual number
of rates in the table will leave out the final rate entry
(mcs15 with half gi in ht40) while forming the valid
rate indices. Not having mcs15+shortGI in ht40 will have
a performance impact (on max throughput) of about 10% both
in nght40 and naht40 mode.
Author: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Date: Thu May 13 18:42:38 2010 -0700
ath9k: Enable Short GI in 20 Mhz for ar9287 and later chips
This patch enables short GI rx at all rates and tx at mcs15
for 20 Mhz channel width also.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For non-AR9271 chips, the credit size is different
and has to be configured appropriately.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR7010 is dual-band. Setup the channels and rateset
for 5GHz band.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rate information on the target has to be updated
for 2-stream devices, along with the correct chainmask.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The supported MCS rate set has to be setup properly
for 2-stream devices.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the USB device IDs for AR7010 and handle
firmware loading properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes programming the byte swap registers
for chipsets other than AR9271. This is needed for
AR7010.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not assign the FW name to driver_info but determine
it dynamically on device probe. This facilitates adding new
firmware.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sta_add/sta_remove are the callbacks that can sleep.
Use them instead of sta_notify.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If buffer is to be accessed by cpu after dma is over, but
between dma mapping and dma unmapping, we should use
dma_sync_single_for_cpu to sync the buffer between cpu with
device. And dma_sync_single_for_device is used to let
device gain the buffer again.
v2: Felix pointed out dma_sync_single_for_device is needed to return
buffer to device if an unsuccessful status bit check is found.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because there is a limited number of tx buffers available, once the
queue has been filled to a certain point, ath9k needs to stop accepting
new frames from mac80211. In order to prevent a full WMM queue from
stopping another queue with fewer frames, this patch limits the number
of queued frames to a quarter of the total available tx buffers, minus
some reserved frames to be used for other purposes (e.g. beacons).
Because tx buffers are reserved for frames when they're staged in
software queues as well, the actual queue depth cannot be used for
this, so this patch stores a reference to the tx queue in the ath_buf
struct and keeps track of the total number of pending frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes beacon distribution in IBSS mode
by configuring the hardware beacon queue properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MIB counters used by ANI have to be disabled
on the host because the FW doesn't do it on the target side.
Also, flush the receive buffers before initializing
RX on the target.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The monitor interface instance on the target has
to be removed before setting it to FULLSLEEP.
Handle this properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ps_idle is protected by the htc_pm_lock mutex.
Use it to protect the variable.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to cancel the PS work when disassociation
happens. The work handlers are cancelled in the stop()
callback.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable the radio only when mac80211 indicates it,
through the IEEE80211_CONF_CHANGE_IDLE flag.
Not handling this properly will result in multiple
calls to radio_disable() even though the radio is
already idle.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW has to be awake when registers are accessed.
Ensure this is so by using the PS wrappers at
appropriate places.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch revamps IDLE power save handling in the driver.
Two separate functions (radio enable/disable) are introduced,
because the semantics of radio handling is just not the same
as the start()/stop() callbacks. For example, the HW must not
be disabled, instead, the PHY has to be disabled in radio_disable().
Also, the HW has to be reset properly in radio enable/disable and
certain registers have to be programmed only once, in the
start() callback.
The radio_enable() routine doesn't need the PS wrappers since
we set the HW power mode to AWAKE anyway before calling it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Async fifo is now enabled only for versions 1.3 and above.
Enable it in the appropriate place, in the reset routine,
instead of process_ini().
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates the PCI power save handling
code, fixing ASPM hangs and handling device state D3
properly.
The WAR register is programmed with the correct
values now.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add a few comments, and move the updation of max_power_level
to a helper routine. This is also done by non-4K based chipsets,
this will be fixed in a separate patch.
* Remove two WARs which are required for old AR5416 chipsets,
and are not needed for AR9287.
* Fix indentation and make things readable.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rather than doing a series of RMWs, calculate the
value to be written to the register in question and
do a single REGWRITE. This improves bringup time.
This depends on the analog_shiftreg configuration option,
which is currently buggy. For AP mode, a delay of 100us
has to be the default. For station mode, this knob has to
be enabled on a per-case basis, though it is a little
unclear on when to enable a delay. This can be fixed later though.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Fix whitespace damage.
* Remove unused debug messages.
* Introduce a macro NUM_EEP_WORDS.
* Convert AR9287 to lowercase in function names.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces the buggy 'ath9k: Group Key fix for VAPs' change.
For AP mode group keys, use the BSSID as lookup mac address, with
the multicast keysearch bit set.
For IBSS mode, use the peer's MAC address with multicast keysearch.
For STA mode, keep using the group key slots.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a MAC address for a key table entry is flagged with the
multicast bit (0x01), indicate to the hardware that multicast
lookup instead of unicast lookup should be used. The multicast
bit itself never makes it to the actual keytable entry register,
as it is shifted out.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We dereference "wmi" on the line before and also when we initialize "ah".
This check has always been after a dereference since the first commit a
couple months ago. Looking through the code, it looks like "wmi" can't
actually be null here so I just removed the check.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rx status length should also be taken into account while
validating the length of a received frame.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Skip the rx status portion in skb->data before accessing ieee80211
frame header.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_rx_skb_preprocess() needs only ieee80211 frame header,
pass only frame headers instead of skb to that function. Also
remove ineffective frame dump in ath9k_process_rate().
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A bunch of data structures are present in the
common module, which are internal to ath9k.
Move them to ath9k.h
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch relocates RX processing code from the
common module to ath9k. This reduces the size
of the common module which is also used by ath9k_htc.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To enable it we now disable and re-enable the PHY chips
after TX IQ calibration.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rx should not be disabed/disabled when hw supports auto sleeping.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add missing code to handle nullfunc frame completion in
ath_tx_edma_tasklet().
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use BSS_CHANGED_HT to handle HT parameter changes.
The rate information on the target has to be updated
to handle changes in HT configuration.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes a large chunk of code dealing
with rate management within the driver and simplifying
things by removing the hacky method of calculating
HT changes. A subsequent patch would fix this by
just using BSS_CHANGED_HT from mac80211.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update from internal systems engineering team.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changed -EINVAL to -EFAULT if copy_to_user() failed.
Changed 0 to -ENOMEM if allocations failed.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The snprintf() function returns the number of bytes that *would* have
been written (not counting the NULL terminator) and that can potentally
be more than the size of the buffer.
In this patch if there were one liners where string clearly fits into
the buffer, then I changed snprintf to sprintf(). It's confusing to use
the return value of snprintf() as a limitter without verifying that it's
smaller than size. This is what initially caught my attention here.
If we use the return value of sprintf() instead future code auditors will
assume we've verified that it fits already.
Also I did find some places where it made sense to use the return value
after we've verified that it is smaller than the buffer size.
Finally the read_file_rcstat() function added an explicit NULL terminator
before calling snprintf(). That's unnecessary because snprintf() will
add the null terminator automatically.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For edma, we should use DMA_BIDIRECTIONAL, or else use
DMA_FROM_DEVICE.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the maximum supported by the firmware.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to determine the HW queue
for each packet that is transmitted. The endpoint
can be chosen directly based on the queue type
that mac80211 sends down.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch initializes the beacon and CAB HW queues
when the driver is loaded.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables short GI rx at all rates and tx at mcs15
for 20 Mhz channel width also.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables the baseband watchdog events for the AR9003
family on ath9k. Upon an a baseband watchdog interrupt we reset
the hardware, this should address corner case conditions where
normal operation can stall. Enable ATH_DBG_RESET to be able
to review details of the bb watchdog interrupt once it happens.
If you're curious how often this happens just grep the debugfs
interrupt file.
Cc: Sam Ng <sam.ng@atheros.com>
Cc: Paul Shaw <paul.shaw@atheros.com>
Cc: Don Breslin <don.breslin@atheros.com>
Cc: Cliff Holden <cliff.holden@atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The baseband watchdog will monitor blocks of the baseband
through timers and will issue an interrupt when things are
detected to be stalled. It is only available on the AR9003
family.
Cc: Sam Ng <sam.ng@atheros.com>
Cc: Paul Shaw <paul.shaw@atheros.com>
Cc: Don Breslin <don.breslin@atheros.com>
Cc: Cliff Holden <cliff.holden@atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This bug was introduced by the following commit
Author: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Date: Thu Apr 15 17:38:46 2010 -0400
ath9k: Remove ATH9K_TX_SW_ABORTED and introduce a bool for this purpose
Wrong buffer is checked for bf_tx_aborted field in ath_tx_num_badfrms(),
this may result in a rate scaling with wrong feedback (number
of unacked frames in this case). It is the last one in the chain
of buffers for an aggregate frame that should be checked.
Also it misses the initialization of this field in the buffer,
this may lead to a situation where we stop the sw retransmission
of failed subframes associated to this buffer.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_print in xmit.c should say "Reseting hardware"
instead of Resetting HAL!(since HAL is being fazed out).
dmesg shows:
[ 8660.899624] ath: Failed to stop TX DMA in 100 msec after killing last frame
[ 8660.899676] ath: Unable to stop TxDMA. Reset HAL!
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With VEOL, Beacon transmission in ad-hoc does not currently work.
I believe for larger ad-hoc networks, VEOL is too unreliable, as
it can get beacon transmissions stuck during synchronization.
Use SWBA based beacon trasmission similar to AP mode instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes IBSS beacon transmissions without VEOL enabled
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functionality to keep the device awake until it is done with
the rx of any mcast/bcast frames which are pending on AP should
also be added to the hardwares which support auto sleep feature.
This patch fixes frequent failures in ARP resolution when it is
initiated by the other end. Currently auto sleep is enabled only
for ar9003 in ath9k.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is obviously a small picky thing. The original error handling code
doesn't free the most recent allocations which haven't been added to the
hif_dev->tx.tx_buf list yet.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After c11d8f89d3b7: "ath9k_htc: Simplify TX URB management" we no longer
assume that tx_buf is a non-null pointer.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 03ceedea97.
This patch was reported to cause a regression in which connectivity is
lost and cannot be reestablished after a suspend/resume cycle.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We tried to squeeze as much AR9003 support into this kernel
release cycle but there are a few features which are still
being tested and developed. Some of these features are critical
to the stable operation of AR9003 so for now disable AR9003 support
all together. This will get re-enabled once all necessary features
are in place but very likely will not happen for 2.6.35.
Reviewed-by: Don Breslin <don.breslin@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
switch and while statements don't need semicolons at end of statement
[ Fixup minor conflicts with recent wimax merge... -DaveM ]
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
It also does not remove null void functions with return.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
with some cleanups by hand.
Compile tested x86 allmodconfig only.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the double swapping of the descriptor data structure, instead
keep it little-endian (native format of the eeprom data), and byteswap
on access.
This allows sparse to verify endian access to the eeprom struct.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ENDPOINT_MAX instead of HST_ENDPOINT_MAX.
This fixes a stack corruption issue.
This is based on a patch sent by Dan Carpenter <error27@gmail.com>.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ready message from the target could be processed
before the host HW init has completed. In this case,
htc_process_target_rdy() would assume the target has timed
out, when it hasn't. Fix this by checking if the target
has sent the ready message properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HTC state has to be setup before initializing
the target because the ready message could possibly
come before the control endpoints in HTC have been
identified.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The URBs have to be allocated before uploading
the firmware to the target. This is needed to process
the target ready message properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since ->sta_notify() can sleep, protect
the callback with a mutex.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't send them for further processing.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These changes include:
* For PAPRD, the TXRF3.capdiv5G, TXRF3.rdiv5G and TXRF3.rdiv2G
are set to 0x0, the TXRF6.capdiv2G is set to 0x2 for all
three chains.
* The d2cas5G/d3cas5G/d4cas5G was updated to 4/4/4 in lowest_ob_db
Tx gain table.
* To improve DPPM, three parameters were updated (Released from Madhan):
1. RANGE_OSDAC is set to 0x1 for 2G, 0x0 for 5G
2. offsetC1 is set to 0xc
3. inv_clk320_adc is set to 0x1
* To reduce PHY error(from spur), cycpwr_thr1 and cycpwr_thr1_ext
are increased to 0x8 at 2G.
* The 2G Rx gain tables are updated with mixer gain setting 3,1,0.
The new checksums yield:
initvals -f ar9003
0x00000000c2bfa7d5 ar9300_2p0_radio_postamble
0x00000000ada2b114 ar9300Modes_lowest_ob_db_tx_gain_table_2p0
0x00000000e0bc2c84 ar9300Modes_fast_clock_2p0
0x00000000056eaf74 ar9300_2p0_radio_core
0x0000000000000000 ar9300Common_rx_gain_table_merlin_2p0
0x0000000078658fb5 ar9300_2p0_mac_postamble
0x0000000023235333 ar9300_2p0_soc_postamble
0x0000000054d41904 ar9200_merlin_2p0_radio_core
0x00000000748572cf ar9300_2p0_baseband_postamble
0x000000009aa5a0a4 ar9300_2p0_baseband_core
0x000000003df9a326 ar9300Modes_high_power_tx_gain_table_2p0
0x000000001cfba124 ar9300Modes_high_ob_db_tx_gain_table_2p0
0x0000000011302700 ar9300Common_rx_gain_table_2p0
0x00000000e3eab114 ar9300Modes_low_ob_db_tx_gain_table_2p0
0x00000000c9d66d40 ar9300_2p0_mac_core
0x000000001e1d0800 ar9300Common_wo_xlna_rx_gain_table_2p0
0x00000000a0c54980 ar9300_2p0_soc_preamble
0x00000000292e2544 ar9300PciePhy_pll_on_clkreq_disable_L1_2p0
0x000000002d3e2544 ar9300PciePhy_clkreq_enable_L1_2p0
0x00000000293e2544 ar9300PciePhy_clkreq_disable_L1_2p0
Cc: Don Breslin <don.breslin@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I changed "> ATH9K_HTC_MAX_TID" to ">= ATH9K_HTC_MAX_TID" to avoid a
potential overflow.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a stray null dereference. We initialize "ista" properly later on.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Paul Shaw <paul.shaw@atheros.com>
Cc: Don Breslin <don.breslin@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Switch LED off/on when handling CONF_CHANGE_IDLE.
Not doing this would leave the radio LED on even
though the chip would be in full sleep mode.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_common (used by ath9k and ath9k_htc) trusts the frames
blessed by hardware as OK are infact correct even if the rate
seen by the driver is unrecognized. ath9k_common just treats
these frames in mac80211 as frames as frames under 1 mbps rate.
It seems this might not be the best thing to do as other parts of
the frame might not be valid so just drop these frames for now.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has no real functional change, this just moves the setting the
the mac80211 rate index into ath9k_process_rate(). This allows us
to eventually make ath9k_process_rate() return a negative value
in case we have detected a specific case rate situation which should
have been ignored.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current way of managing beaconing in ad-hoc
mode has a subtle race - the beacon obtained from mac80211
is freed in the SWBA handler rather than the TX
completion routine. But transmission of beacons goes
through the normal SKB queue maintained in hif_usb,
leading to a situation where __skb_dequeue() in the TX
completion handler goes kaput.
Fix this by simply getting a beacon from mac80211 for
every SWBA and free it in its completion routine.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Atheros hardware supports receiving frames that span multiple
descriptors and buffers. In this case, the rx status of every
descriptor except for the last one is invalid and may contain random
data. Because the driver does not support this, it needs to drop such
frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If bit 29 is set, MAC H/W can attempt to decrypt the received aggregate
with WEP or TKIP, eventhough the received frame may be a CRC failed
corrupted frame. If this bit is set, H/W obeys key type in keycache.
If it is not set and if the key type in keycache is neither open nor
AES, H/W forces key type to be open. But bit 29 should be set to 1
for AsyncFIFO feature to encrypt/decrypt the aggregate with WEP or TKIP.
Cc: stable@kernel.org
Reported-by: Johan Hovold <johan.hovold@lundinova.se>
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: Ranga Rao Ravuri <ranga.ravuri@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX interrupt mitigation reduces the number of interrupts
by addressing several interrupt actions (AR_IMR_TXOK,
AR_IMR_TXDESC) all in one interrupt so when enabling
it discard setting the other interrupts.
Without this TX interrupt mitigation would actually
increase the number of interrupts two-fold. We still
leave TX interrupt mitigation disabled as it is still
being tested.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the noisefloor calibration times out, do not load -50 into
the registers, since this might cause rx issues. Instead, leave
enough time for the noise floor calibration to complete until
the next check.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the new AR9003 EEPROM code does tune the card for the configured
tx power level, we need to fill in the correct power limits in the TPC
part of the DMA descriptor.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Combine multiple checks that were supposed to check for the same
conditions, but didn't. Always enable fast PLL clock on AR9280 2.0
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fast clock operation (44Mhz) is enabled for 5Ghz in ar9003, so
take care of the conversion from usec to hw clock.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable TX IQ calibration, it was prematurely enabled in
previous versions.
Cc: Paul Shaw <Paul.Shaw@Atheros.com>
Cc: Thomas Hammel <Thomas.Hammel@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This synchs up the initvals to the values used on the
Atheros HAL for AR9003. This specific change adds support
for a new high power module.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A bunch of validation and processing in the RX IRQ handler
can be moved to the RX tasklet. The IRQ handler is
already heavy, with the memory allocation for handling
stream mode. Also, a memcpy of 40 bytes for every packet
can be avoided in the handler.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check for the endpoint IDs when processing
TX completions and drop the unsupported EPIDs.
We can add other endpoints (UAPSD,..) when support
is added.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All commands to the target are disabled when the device
is unplugged, but a normal module unload has to be
differentiated from this case, as we could still receive
data in the RX endpoint. Fix this by checking if the
device is attached or not.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My patch "ath9k_htc: Handle WMI timeouts properly" introduced
a race condition in WMI command processing. The last issued command
should be stored _before_ issuing a WMI command. Not doing this
would result in the WMI event IRQ dropping correct command responses
as invalid.
Fix this race by storing the command id correctly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Completion of WMI commands take a longer time
on some platforms. Increase the timeout value
to handle this.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When handling the REGIN callback, processing
the incoming data first should be the preferred
mode of operation. Allocation of a new SKB may fail,
in which case, the URB will not be resubmitted.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So, apparently there is a USB reboot command
that the target accepts. Using this instead of
usb_reset_device() fixes the issue of "descriptor read error"
that pops up on repeated load/unload.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the TX callback, the HTC layer has to pass the
priv pointer that was registered during service initialization.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no reason to disable the PHY Error / MIB counters
when the module is being unloaded.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a code segment in configpciepowersave()
to make use of multiple register writes.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the USB device has been unplugged, there is
no point in trying to send commands to the target.
Fix this by denying all WMI commands in such a case.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch simplifies URB management for transmission,
by removing the 'FLUSH' variable (which is not needed,
since we can determine if the URB has been killed by
looking at the URB status), and also handling the STOP
case properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes ar5416Addac_9160 and ar5416Addac_9160 const
I guess we skipped them long ago.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Supported only for single stream rates by the hardware
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9300 based hardware can 3x3 MCS rates, this should be set in the
HT capabilities.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of increasing bits_per_symbol for supporting more streams, keep
it single-stream only and multiply the values by the numer of streams.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Include MCS0-31 and also add SGI for HT20. This makes it
possible to support more different rate combinations with
newer hardware.
Based on a patch by Selvam. T.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I set up multiple VAPs with ath9k, I encountered an issue that
the traffic may be lost after a while.
The detailed phenomenon is
1. After a while the clients connected to one of these VAPs will get
into a state that no broadcast/multicast packets can be transfered
successfully while the unicast packets can be transfered normally.
2. Minutes latter the unitcast packets transfer will fail as well,
because the ARP entry is expired and it can't be freshed due to the
broadcast trouble.
It's caused by the group key overwritten and someone discussed this
issue in ath9k-devel maillist before, but haven't work out a fix yet.
I referred the method in madwifi, and made a patch for ath9k.
The method is to set the high bit of the sender(AP)'s address, and
associated that mac and the group key. It requires the hardware
supports multicast frame key search. It seems true for AR9160.
Not sure whether it's the correct way to fix this issue. But it seems
to work in my test. The patch is attached, feel free to revise it.
Signed-off-by: Daniel Yingqiang ma <yma.cool@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bunch of endian issues that
were exposed by sparse. It's a miracle that the driver
worked at all till now.
The Lord be praised.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a WMI command has timed out for some reason,
a late WMI response would end up updating the
response region of a new WMI request that has been
issued in the meantime.
Fix this race condition by dropping a WMI response
if a new WMI command has been issued.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no point in trying to set the LED pin
when the module is being unloaded. The target
would be reset anyway.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds macros at certain places
which could be optimized for multiple register writes.
The performance of ath9k_htc improves considerably,
especially reducing the latency involved in a scan run.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Programming the opmode in the HW can be done
before the assoc_id and STA_ID registers are
setup. This helps ath9k_htc when multiple register
writes are used.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for writing multiple registers
in a single USB command.
Specific calls from the HW code that performs multiple
register writes would be modified to make use of this
in subsequent patches.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up beacon configuration,
removing a redundant interface type check
and updating beacon interval in the correct place.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to tests, both TSF lower and upper registers kept counting, so
the higher part could have been updated after the lower part has been
read, as shown in the following log where the upper part is read first
and the lower part next.
tsf = {00000003-fffffffd}
tsf = {00000003-00000001}
tsf = {00000004-0000000b}
This patch corrects this by checking that the upper part has not been
changed while the lower part was read. It has been tested in an IBSS
network where artifical IBSS merges have been done in order to trigger
hundreds of rollover for the TSF lower part.
It follows the logic mentionned by Derek, with only 2 register reads
needed at each additional steps instead of 3 (the minimum number of
register reads is still 3).
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The first AR9003 hardware family device supported is the
AR9300, which has the vendor:device id 168c:0030
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LDPC is enabled by the rate control if the its determined
that the target peer supports LDPC. We would have already
intersected the HT capabilities so if our peer supports
LDPC so do we.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also add a function to clean up tx status ring.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable CRC check on the descriptor fetched from host on AR9003
upon reseting the TX queue.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also reset tx status ring suring chip reset.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9002 hardware code enables aggregation for WEP but
mac80211 doesn't enable aggregation with WEP, and the AR9003
code family does not need this so skip it for now for AR9003
but leave the code and annotate we should eventually consider
how to remove this in consideration for the HAL unification
goals.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The asynch fifo code is specific to >= AR9287 so stuff it
into the AR9002 hardware family code and skip it for AR9003
cards.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is done depending on what the EEPROM settings indicates.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We add this now as OFDM spur mitigation required accessing
the EEPROM for the AR9003 devices.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Once upon a time the AR_EEPROM_MAC macro was added to let us
add a random attribute to the three 4-bytes of MAC addresses
entries we read from the EEPROM. This was good while a random
high-enough value was used which did not conflict with any
of the already existing enum eeprom_param values. With AR9003
support the enums overlap and it means we either increment
the random offset or just restore the reading logic to match
what the HAL has. I choose to do the later to synchronize
the logic on both code bases.
This should fix reading the MAC address from the EEPROM
on AR9003 hardware.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This goes with some new shiny TX IQ calibration that AR9003
hardware family supports.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the last call on calib.c which acceses PHY stuff,
with this change we calib.c is now generic between both
all supported hardware families.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is so we can share routines which access this register
on calib.c
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also move interrupt related code to mac.c
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9003 TX/RX gain is currently initialized with the other
components, so for now AR9003 does not implment this callback,
after hardware bring up we can test moving the TX/RX gain there
as well and if it works well move them to its own callback as
well.
Since all INI stuff is now moved out hw.c no longer needs to
include and touch any original INI headers/structs.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is specific to the AR9002 family only.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move out the generic hardware family code out into their own
files, we have one for AR5008, AR9001, and AR9002 family (ar9002_hw.c)
and another file for the new AR9003 hardware family (ar9003_hw.c).
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calibration code touches phy registers and since these
change the calibration code needs to be abstracted.
Noise floor calibration is the only thing remaining but
since the remaining calls only touch the AR_PHY_AGC_CONTROL
register we'll just define that register conditionally, that
will be done separately. The goal is to remove the dependency
of ar9002_phy.h on calib.c
This also adds stubs to be filled for AR9003 calibration code.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The calibration settings should go into the respective
hardware family AR9002 calibration settings callback,
ar9002_hw_init_cal_settings().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can do the family revision check on the top level caller.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We're bailing out on the alternative code path so remove the
else branch.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Open Loop Control temperature compensation changes between our
hardware so use a helper for it.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code can be simplified and shared between two locations if we bring
this into a helper. During reset we do not account for the skip count.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can reorganize the code in such a way that eep_map can be removed,
which makes the code more clearer.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Store appropriate desc length which will be used by the
ath9k module while duplicating tx desc.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9003 hardware family now initializes hardware by block
components and into stages: pre, core and init.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The initvals.h file is over 7000 lines now, so instead of adding
AR9003 initvals to it instead lets split the current initvals.h by
hardware family: AR5008, AR9001, AR9002
The AR9003 family will have its own initval file later.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, no need for the udelay(2) on AR9003 hardware.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9003 family requires a change on the loop and can also skip
testing the PHY timing registers. This chip test can now be used
by all Atheros hardware families, including legacy. We can
eventually move this out to the generic ath module.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Set rx buf size in register 0x60
* Set rxdp on the respective hw rx queue (HP and LP queues)
* Process rx descriptor
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HP & LP queue depth and rx status length.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9003 supports extended DMA (EDMA), this comes with some
bells and whistles on top of the legacy DMA that we are used
to. Mark AR9003 and later chips EDMA capable.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ANI is still being debugged on AR9003 by our systems team
so it should not yet be enabled yet. When ANI will be
enabled all ANI functionality is expected to be enabled
so fill the ANI functionality to all for AR9003 for now
as well.
Cc: Enis Akay <Enis.Akay@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows us to add SREV checks on these helpers.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This add stubs for PHY support for the AR9003 hardware family.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, clean up and reorganize the AR9287 macro to have better
ordering. We won't add the PCI ID to the supported device list
until we have some functional code for it.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PLL control computation used to program the AR_RTC_PLL_CONTROL
register varies between our harware so just add a private callback for it.
AR9003 will use its own callback.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not required for the AR9003 family.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PHY split is easier done in a few steps. First move
the RF ops to the private ops and rename them accordingly.
We split PHY stuff up first for the AR5008 and AR9002
families. There are some callbacks that AR9002 share
with the AR5008 familiy so we set those first, if AR9002
has some different callbacks it will override them upon
hardware init.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau