drm/i915 fixes for v5.15-rc2:
- Propagate DP link training error returns
- Use max link params for eDP 1.3 and earlier
- Build warning fixes
- Gem selftest fixes
- Ensure wakeref is held before hardware access
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8735q4wsu7.fsf@intel.com
tx timeout and slot time are currently specified in units of HZ. On
Alpha, HZ is defined as 1024. When building alpha:allmodconfig, this
results in the following error message.
drivers/net/hamradio/6pack.c: In function 'sixpack_open':
drivers/net/hamradio/6pack.c:71:41: error:
unsigned conversion from 'int' to 'unsigned char'
changes value from '256' to '0'
In the 6PACK protocol, tx timeout is specified in units of 10 ms and
transmitted over the wire:
https://www.linux-ax25.org/wiki/6PACK
Defining a value dependent on HZ doesn't really make sense, and
presumably comes from the (very historical) situation where HZ was
originally 100.
Note that the SIXP_SLOTTIME use explicitly is about 10ms granularity:
mod_timer(&sp->tx_t, jiffies + ((when + 1) * HZ) / 100);
and the SIXP_TXDELAY walue is sent as a byte over the wire.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes a very annoying issue where the driver view of the MMU state gets
out of sync with the actual hardware state across a runtime PM cycle,
so we end up restarting the GPU with the wrong (potentially already
freed) MMU context. Hilarity ensues.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lucas Stach <l.stach@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/729a561b6cfed090457bcc856a9e14ed6209fe21.camel@pengutronix.de
With the new static annotation, the compiler warns when the functions
are actually unused:
drivers/gpu/drm/rockchip/cdn-dp-core.c:1123:12: error: 'cdn_dp_resume' defined but not used [-Werror=unused-function]
1123 | static int cdn_dp_resume(struct device *dev)
| ^~~~~~~~~~~~~
Mark them __maybe_unused to suppress that warning as well.
[ Not so 'new' static annotations any more, and I removed the part of
the patch that added __maybe_unused to cdn_dp_suspend(), because it's
used by the shutdown/remove code.
So only the resume function ends up possibly unused if CONFIG_PM isn't
set - Linus ]
Fixes: 7c49abb4c2 ("drm/rockchip: cdn-dp-core: Make cdn_dp_core_suspend/resume static")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some drivers pass a pointer to volatile data to virt_to_bus() and
virt_to_phys(), and that works fine. One exception is alpha. This
results in a number of compile errors such as
drivers/net/wan/lmc/lmc_main.c: In function 'lmc_softreset':
drivers/net/wan/lmc/lmc_main.c:1782:50: error:
passing argument 1 of 'virt_to_bus' discards 'volatile'
qualifier from pointer target type
drivers/atm/ambassador.c: In function 'do_loader_command':
drivers/atm/ambassador.c:1747:58: error:
passing argument 1 of 'virt_to_bus' discards 'volatile'
qualifier from pointer target type
Declare the parameter of virt_to_phys and virt_to_bus as pointer to
volatile to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver isn't enabled most places because of the ISA config
dependency, but alpha still has it. And I think the 'Jensen' actually
did have an ISA slot.
However, it doesn't build cleanly, because the "Vortex bus master" code
just casts the skb->data pointer to 'int':
outl((int) (skb->data), ioaddr + Wn7_MasterAddr);
which is all kinds of broken. Even on a good old traditional PC/AT it
would be broken because the high bits will be random kernel address
bits, but presumably the hardware ignores those bits. I mean, it's ISA.
We're talking 16MB dma limits. The "good old days".
Make the build happy with this kind of craziness by using the proper
isa_virt_to_bus() handling that the full bus master code uses anyway
(the Vortex bus mastering is a limited special case).
Who knows, this might even work.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One patch which fixes a build warning when using the PAGE0 pointer.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCYUNgkQAKCRD3ErUQojoP
X1J+AQCJol1vKuAJQQEXPrB6s1Hu/gkQpOc/MrmNXUj5ZpgH/QD/V3JQzHMOQNpx
uo3UgZ7sg+GnhJ1NIQ2zjXSBitAoaQI=
=GGF7
-----END PGP SIGNATURE-----
Merge tag 'for-5.15/parisc-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fix from Helge Deller:
"Fix a build warning when using the PAGE0 pointer"
* tag 'for-5.15/parisc-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Use absolute_pointer() to define PAGE0
__stack_chk_guard is setup once while init stage and never changed
after that.
Although the modification of this variable at runtime will usually
cause the kernel to crash (so does the attacker), it should be marked
as __ro_after_init, and it should not affect performance if it is
placed in the ro_after_init section.
Signed-off-by: Dan Li <ashimida@linux.alibaba.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/1631612642-102881-1-git-send-email-ashimida@linux.alibaba.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Remove all but the first include of linux/sched.h from process.c
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20210902011126.29828-1-lv.ruyi@zte.com.cn
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When we need a buffer for SVE register state we call sve_alloc() to make
sure that one is there. In order to avoid repeated allocations and frees
we keep the buffer around unless we change vector length and just memset()
it to ensure a clean register state. The function that deals with this
takes the task to operate on as an argument, however in the case where we
do a memset() we initialise using the SVE state size for the current task
rather than the task passed as an argument.
This is only an issue in the case where we are setting the register state
for a task via ptrace and the task being configured has a different vector
length to the task tracing it. In the case where the buffer is larger in
the traced process we will leak old state from the traced process to
itself, in the case where the buffer is smaller in the traced process we
will overflow the buffer and corrupt memory.
Fixes: bc0ee47603 ("arm64/sve: Core task context handling")
Cc: <stable@vger.kernel.org> # 4.15.x
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210909165356.10675-1-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
[Why]
The "base_addr_is_mc_addr" field was added for dcn3.1 support but
pa_config was never updated to set it to false.
Uninitialized memory causes it to be set to true which results in
address mistranslation and white screen.
[How]
Use memset to ensure all fields are initialized to 0 by default.
Fixes: 64b1d0e8d5 ("drm/amd/display: Add DCN3.1 HWSEQ")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This patch allows panel orientation quirks from DRM core to be
used. They attach a DRM connector property "panel orientation"
which indicates in which direction the panel has been mounted.
Some machines have the internal screen mounted with a rotation.
Since the panel orientation quirks need the native mode from the
EDID, check for it in amdgpu_dm_connector_ddc_get_modes.
Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As the user cannot do anything about the unsupported Trusted Memory Zone
(TMZ) feature, do not warn about it, but make it informational, so
demote the log level from warning to info.
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This was unusual; normally, inline functions are declared static as
well, and defined in a header file if used by multiple compilation
units. The latter would be more involved in this case, so just drop
the inline declaration for now.
Fixes compile failure building for ppc64le on RHEL 8:
In file included from ../drivers/gpu/drm/amd/amdgpu/amdgpu_ras.h:32,
from ../drivers/gpu/drm/amd/amdgpu/amdgpu_ras.c:33:
../drivers/gpu/drm/amd/amdgpu/amdgpu_ras.c: In function ‘amdgpu_ras_recovery_init’:
../drivers/gpu/drm/amd/amdgpu/amdgpu_ras_eeprom.h:90:17: error: inlining failed in call
to ‘always_inline’ ‘amdgpu_ras_eeprom_max_record_count’: function body not available
90 | inline uint32_t amdgpu_ras_eeprom_max_record_count(void);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/gpu/drm/amd/amdgpu/amdgpu_ras.c:1985:34: note: called from here
1985 | max_eeprom_records_len = amdgpu_ras_eeprom_max_record_count();
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: c84d46707e "drm/amdgpu: validate bad page threshold in ras(v3)"
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Current RUNPM mechanism relies on PMFW to master the timing for BACO
in/exit. And that needs cooperation from sound driver for dstate
change notification for function 1(audio). Otherwise(on sound driver
missing), BACO cannot be kicked in correctly and hang will be observed
on RUNPM exit.
By switching back to legacy message way on sound driver missing,
we are able to fix the runpm hang observed for the scenario below:
amdgpu driver loaded -> runpm suspend kicked -> sound driver loaded
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reported-and-tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Pass drm dev directly as rdev->ddev gets initialized later on
at radeon_device_init().
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=214375
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Separate iommu_resume from kfd_resume, and move it before
other amdgpu ip init/resume.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=211277
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Separate kfd_iommu_resume from kfd_resume for fine-tuning
of amdgpu device init/resume/reset/recovery sequence.
v2: squash in fix for !CONFIG_HSA_AMD
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=211277
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
If link training is aborted, it shall be retried if sink is present.
[How]
Check hpd status to find out whether sink is present or not. If sink is
present, then link training shall be tried again with same settings.
Otherwise, link training shall be aborted.
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Intermittently, there presents two occurrences of 0 stream
commits in a single HPD event. Current HDCP sequence does
not consider such scenerio, and will thus disable HDCP.
[How]
Add condition check to include stream remove and re-enable
case for HDCP enable.
Reviewed-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
call stack of amdgpu dsc mst pbn, slot num calculation is as below:
-compute_bpp_x16_from_target_bandwidth
-decide_dsc_target_bpp_x16
-setup_dsc_config
-dc_dsc_compute_bandwidth_range
-compute_mst_dsc_configs_for_link
-compute_mst_dsc_configs_for_state
from pbn -> dsc target bpp_x16
bpp_x16 is calulated by compute_bpp_x16_from_target_bandwidth.
Beside pixel clock and bpp, num_slices_h and bpp_increment_div
will also affect bpp_x16.
from dsc target bpp_x16 -> pbn
within dm_update_mst_vcpi_slots_for_dsc,
pbn = drm_dp_calc_pbn_mode(clock, bpp_x16, true);
drm_dp_calc_pbn_mode(int clock, int bpp, bool dsc)
{
return DIV_ROUND_UP_ULL(mul_u32_u32(clock * (bpp / 16), 64 * 1006),
8 * 54 * 1000 * 1000);
}
bpp / 16 trunc digits after decimal point. This will cause calculation
delta. drm_dp_calc_pbn_mode does not have other informations,
like num_slices_h, bpp_increment_div. therefore, it does not do revese
calcuation properly from bpp_x16 to pbn.
pbn from drm_dp_calc_pbn_mode is less than pbn from
compute_mst_dsc_configs_for_state. This cause not enough mst slot
allocated to display. display could not visually light up.
[How]
pass pbn from compute_mst_dsc_configs_for_state to
dm_update_mst_vcpi_slots_for_dsc
Cc: stable@vger.kernel.org
Reviewed-by: Scott Foster <Scott.Foster@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Hersen Wu <hersenwu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On Carrizo/Stoney systems we set backlight through panel_cntl, i.e.
directly via the PWM registers, if DMCU is not initialized. We
always read it back through ABM registers which leads to a
mismatch and forces atomic_commit to program the backlight
each time.
Instead make sure we use the same logic for backlight readback,
i.e. read it from panel_cntl if DMCU is not initialized.
We also need to remove some extraneous and incorrect calculations
at the end of dce_get_16_bit_backlight_from_pwm.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1666
Cc: stable@vger.kernel.org
Reviewed-by: Josip Pavic <josip.pavic@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On some GPUs the PCIe atomic requirement for KFD depends on the MEC
firmware version. Add a firmware version check for this. The minimum
firmware version that works without atomics can be updated in the
device_info structure for each GPU type.
Move PCIe atomic detection from kgd2kfd_probe into kgd2kfd_device_init
because the MEC firmware is not loaded yet at the probe stage.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add manual sclk/vddc setting supoort via pp_od_clk_voltage sysfs
to maintain consistency with other asics. As cyan skillfish doesn't
support DPM, there is only a single frequency and voltage to adjust.
v2: maintain consistency and add command guide.
v3: adjust user settings storage and coding style.
Command guide:
echo vc point sclk vddc > pp_od_clk_voltage
"vc" - sclk voltage curve
"point" - must be 0
"sclk" - target value of sclk(MHz), should be in safe range
"vddc" - target value of vddc(mV), a 6.25(mV) stepping is
recommended and should be in safe range (the real
vddc is an approximation of target value)
echo c > pp_od_clk_voltage
"c" - commit the changes of sclk and vddc, only after
the commit command, the target values set by "vc"
command will take effect
echo r > pp_od_clk_voltage
"r" - reset sclk and vddc to default value, a subsequent
commit command is needed to take effect
Example:
1) Check default sclk and vddc
$ cat pp_od_clk_voltage
OD_SCLK:
0: 1800Mhz *
OD_VDDC:
0: 862mV *
OD_RANGE:
SCLK: 1000Mhz 2000Mhz
VDDC: 700mV 1129mV
2) Set sclk to 1500MHz and vddc to 700mV
$ echo vc 0 1500 700 > pp_od_clk_voltage
$ echo c > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 1500Mhz *
OD_VDDC:
0: 693mV *
OD_RANGE:
SCLK: 1000Mhz 2000Mhz
VDDC: 700mV 1129mV
3) Reset sclk and vddc to default
$ echo r > pp_od_clk_voltage
$ echo c > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 1800Mhz *
OD_VDDC:
0: 874mV *
OD_RANGE:
SCLK: 1000Mhz 2000Mhz
VDDC: 700mV 1129mV
NOTE:
We don't specify an explicit safe range, you can set any values
between min and max at your own risk. Enjoy!
Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add print_clk_levels and read_sensor pptable funcs for
cyan skilfish.
v2: keep consitency and add get_gpu_metrics callback.
v3: use sysfs_emit_at() in sysfs show function.
Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add SmuMetrics_t definition for cyan skilfish.
v2: update SmuMetrics_t definition.
v3: cleanup and rearrange the order of fields.
Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add some PPSMC MSGs for cyan skilfish.
Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Assert only when FPU is not enabled.
Fixes: 0ea7ee8217 ("drm/amd/display: Add DC_FP helper to check FPU state")
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If we're running a headless config with 0 links then the vblank
workqueue will be NULL - causing a NULL pointer exception during
any commit.
[How]
Guard access to the workqueue if it's NULL and don't queue or flush
work if it is.
Reported-by: Mike Lothian <mike@fireburn.co.uk>
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1700
Fixes: 58aa1c50e5 ("drm/amd/display: Use vblank control events for PSR enable/disable")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The network interface managed by the mlxbf_gige driver can
get into a problem state where traffic does not flow.
In this state, the interface will be up and enabled, but
will stop processing received packets. This problem state
will happen if three specific conditions occur:
1) driver has received more than (N * RxRingSize) packets but
less than (N+1 * RxRingSize) packets, where N is an odd number
Note: the command "ethtool -g <interface>" will display the
current receive ring size, which currently defaults to 128
2) the driver's interface was disabled via "ifconfig oob_net0 down"
during the window described in #1.
3) the driver's interface is re-enabled via "ifconfig oob_net0 up"
This patch ensures that the driver's "valid_polarity" field is
cleared during the open() method so that it always matches the
receive polarity used by hardware. Without this fix, the driver
needs to be unloaded and reloaded to correct this problem state.
Fixes: f92e1869d7 ("Add Mellanox BlueField Gigabit Ethernet driver")
Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: David Thompson <davthompson@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checking tunnel offloading, it turns out that offloading doesn't work
as expected. The following script allows to reproduce the issue.
Call it as `testscript DEVICE LOCALIP REMOTEIP NETMASK'
=== SNIP ===
if [ $# -ne 4 ]
then
echo "Usage $0 DEVICE LOCALIP REMOTEIP NETMASK"
exit 1
fi
DEVICE="$1"
LOCAL_ADDRESS="$2"
REMOTE_ADDRESS="$3"
NWMASK="$4"
echo "Driver: $(ethtool -i ${DEVICE} | awk '/^driver:/{print $2}') "
ethtool -k "${DEVICE}" | grep tx-udp
echo
echo "Set up NIC and tunnel..."
ip addr add "${LOCAL_ADDRESS}/${NWMASK}" dev "${DEVICE}"
ip link set "${DEVICE}" up
sleep 2
ip link add vxlan1 type vxlan id 42 \
remote "${REMOTE_ADDRESS}" \
local "${LOCAL_ADDRESS}" \
dstport 0 \
dev "${DEVICE}"
ip addr add fc00::1/64 dev vxlan1
ip link set vxlan1 up
sleep 2
rm -f vxlan.pcap
echo "Running tcpdump and iperf3..."
( nohup tcpdump -i any -w vxlan.pcap >/dev/null 2>&1 ) &
sleep 2
iperf3 -c fc00::2 >/dev/null
pkill tcpdump
echo
echo -n "Max. Paket Size: "
tcpdump -r vxlan.pcap -nnle 2>/dev/null \
| grep "${LOCAL_ADDRESS}.*> ${REMOTE_ADDRESS}.*OTV" \
| awk '{print $8}' | awk -F ':' '{print $1}' \
| sort -n | tail -1
echo
ip link del vxlan1
ip addr del ${LOCAL_ADDRESS}/${NWMASK} dev "${DEVICE}"
=== SNAP ===
The expected outcome is
Max. Paket Size: 64904
This is what you see on igb, the code igc has been taken from.
However, on igc the output is
Max. Paket Size: 1516
so the GSO aggregate packets are segmented by the kernel before calling
igc_xmit_frame. Inside the subsequent call to igc_tso, the check for
skb_is_gso(skb) fails and the function returns prematurely.
It turns out that this occurs because the feature flags aren't set
entirely correctly in igc_probe. In contrast to the original code
from igb_probe, igc_probe neglects to set the flags required to allow
tunnel offloading.
Setting the same flags as igb fixes the issue on igc.
Fixes: 34428dff36 ("igc: Add GSO partial support")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the assert from the callback priv lookup function since it does
not require RTNL lock and is already protected by flow_indr_block_lock.
This will avoid warnings from being emitted to dmesg if the driver
registers its callback after an ingress qdisc was created for a
netdevice.
The warnings started after the following patch was merged:
commit 74fc4f8287 ("net: Fix offloading indirect devices dependency on qdisc order creation")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was used but never set. The hardcoded value from before the dawn of
time was non-standard; the usual name for cross-tools is $TRIPLET-$TOOL
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Should not use comparison of unsigned expressions < 0.
Signed-off-by: Xiang wangx <wangxiang@cdjrlc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we forcefully evict a mapping from the the address space and thus the
MMU context, the MMU context is leaked, as the mapping no longer points to
it, so it doesn't get freed when the GEM object is destroyed. Add the
mssing context put to fix the leak.
Cc: stable@vger.kernel.org # 5.4
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Move the refcount manipulation of the MMU context to the point where the
hardware state is programmed. At that point it is also known if a previous
MMU state is still there, or the state needs to be reprogrammed with a
potentially different context.
Cc: stable@vger.kernel.org # 5.4
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
After a reset the GPU is no longer using the MMU context and may be
restarted with a different context. While the mmu_state proeprly was
cleared, the context wasn't unreferenced, leading to a memory leak.
Cc: stable@vger.kernel.org # 5.4
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
When the GPU is reset both the current exec state, as well as all MMU
state is lost. Move the driver side state tracking into the reset function
to keep hardware and software state from diverging.
Cc: stable@vger.kernel.org # 5.4
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The MMU state may be kept across a runtime suspend/resume cycle, as we
avoid a full hardware reset to keep the latency of the runtime PM small.
Don't pretend that the MMU state is lost in driver state. The MMU
context is pushed out when new HW jobs with a different context are
coming in. The only exception to this is when the GPU is unbound, in
which case we need to make sure to also free the last active context.
Cc: stable@vger.kernel.org # 5.4
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
While the DMA frontend can only be active when the MMU context is set, the
reverse isn't necessarily true, as the frontend can be stopped while the
MMU state is kept. Stop treating mmu_context being set as a indication that
the frontend is running and instead add a explicit property.
Cc: stable@vger.kernel.org # 5.4
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The prev context is the MMU context at the time of the job
queueing in hardware. As a job might be queued multiple times
due to recovery after a GPU hang, we need to make sure to put
the stale prev MMU context from a prior queuing, to avoid the
reference and thus the MMU context leaking.
Cc: stable@vger.kernel.org # 5.4
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Being able to have the refcount manipulation in an assignment makes
it much easier to parse the code.
Cc: stable@vger.kernel.org # 5.4
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Dave Airlie