The acpi_pci_propagate_wakeup() routine is there to handle cases in
which PCI bridges (or PCIe ports) are expected to signal wakeup
for devices below them, but currently it doesn't do that correctly.
The problem is that acpi_pci_propagate_wakeup() uses
acpi_pm_set_device_wakeup() for bridges and if that routine is
called for multiple times to disable wakeup for the same device,
it will disable it on the first invocation and the next calls
will have no effect (it works analogously when called to enable
wakeup, but that is not a problem).
Now, say acpi_pci_propagate_wakeup() has been called for two
different devices under the same bridge and it has called
acpi_pm_set_device_wakeup() for that bridge each time. The
bridge is now enabled to generate wakeup signals. Next,
suppose that one of the devices below it resumes and
acpi_pci_propagate_wakeup() is called to disable wakeup for that
device. It will then call acpi_pm_set_device_wakeup() for the bridge
and that will effectively disable remote wakeup for all devices under
it even though some of them may still be suspended and remote wakeup
may be expected to work for them.
To address this (arguably theoretical) issue, allow
wakeup.enable_count under struct acpi_device to grow beyond 1 in
certain situations. In particular, allow that to happen in
acpi_pci_propagate_wakeup() when wakeup is enabled or disabled
for PCI bridges, so that wakeup is actually disabled for the
bridge when all devices under it resume and not when just one
of them does that.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The run_wake flag in struct dev_pm_info is used to indicate whether
or not the device is capable of generating remote wakeup signals at
run time (or in the system working state), but the distinction
between runtime remote wakeup and system wakeup signaling has always
been rather artificial. The only practical reason for it to exist
at the core level was that ACPI and PCI treated those two cases
differently, but that's not the case any more after recent changes.
For this reason, get rid of the run_wake flag and, when applicable,
use device_set_wakeup_capable() and device_can_wakeup() instead of
device_set_run_wake() and device_run_wake(), respectively.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
After previous changes it is not necessary to distinguish between
device wakeup for run time and device wakeup from system sleep states
any more, so rework the PCI device wakeup settings code accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The pme_interrupt flag in struct pci_dev is set when PMEs generated
by the device are going to be signaled via root port PME interrupts.
Ironically enough, that information is only used by the code setting
up device wakeup through ACPI which returns as soon as it sees the
pme_interrupt flag set while setting up "remote runtime wakeup".
That is questionable, however, because in theory there may be PCIe
devices using out-of-band PME signaling under root ports handled
by the native PME code or devices requiring wakeup power setup to be
carried out by AML. For such devices, ACPI wakeup should be invoked
regardless of whether or not native PME signaling is used in general.
For this reason, drop the pme_interrupt flag and rework the code
using it which then allows the ACPI-based device wakeup handling
in PCI to be consolidated to use one code path for both "runtime
remote wakeup" and system wakeup (from sleep states).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Currently, there are two separate ways of handling device wakeup
settings in the ACPI core, depending on whether this is runtime
wakeup or system wakeup (from sleep states). However, after the
previous commit eliminating the run_wake ACPI device wakeup flag,
there is no difference between the two any more at the ACPI level,
so they can be combined.
For this reason, introduce acpi_pm_set_device_wakeup() to replace both
acpi_pm_device_run_wake() and acpi_pm_device_sleep_wake() and make it
check the ACPI device object's wakeup.valid flag to determine whether
or not the device can be set up to generate wakeup signals.
Also notice that zpodd_enable/disable_run_wake() only call
device_set_run_wake() because acpi_pm_device_run_wake() called
device_run_wake(), which is not done by acpi_pm_set_device_wakeup(),
so drop the now redundant device_set_run_wake() calls from there.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The run_wake flag in struct acpi_device_wakeup_flags stores the
information on whether or not the device can generate wakeup
signals at run time, but in ACPI that really is equivalent to
being able to generate wakeup signals at all.
In fact, run_wake will always be set after successful executeion of
acpi_setup_gpe_for_wake(), but if that fails, the device will not be
able to use a wakeup GPE at all, so it won't be able to wake up the
systems from sleep states too. Hence, run_wake actually means that
the device is capable of triggering wakeup and so it is equivalent
to the valid flag.
For this reason, drop run_wake from struct acpi_device_wakeup_flags
and make sure that the valid flag is only set if
acpi_setup_gpe_for_wake() has been successful.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The work functions provided by the users of acpi_add_pm_notifier()
should be run synchronously before re-enabling the wakeup GPE in
case they are used to clear the status and/or disable the wakeup
signaling at the source. Otherwise, which is the case currently in
the PCI bus type code, the same wakeup event may be signaled for
multiple times while the execution of the work function in response
to it has already been queued up.
Fortunately, acpi_add_pm_notifier() is only used by PCI and by
ACPI device PM code internally, so the change is relatively
straightforward to make.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
acpi_evaluate_dsm() and friends take a pointer to a raw buffer of 16
bytes. Instead we convert them to use guid_t type. At the same time we
convert current users.
acpi_str_to_uuid() becomes useless after the conversion and it's safe to
get rid of it.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
* pci/pm:
x86/platform/intel-mid: Constify mid_pci_platform_pm
PCI: pciehp: Add runtime PM support for PCIe hotplug ports
ACPI / hotplug / PCI: Make device_is_managed_by_native_pciehp() public
ACPI / hotplug / PCI: Use cached copy of PCI_EXP_SLTCAP_HPC bit
PCI: Unfold conditions to block runtime PM on PCIe ports
PCI: Consolidate conditions to allow runtime PM on PCIe ports
PCI: Activate runtime PM on a PCIe port only if it can suspend
PCI: Speed up algorithm in pci_bridge_d3_update()
PCI: Autosense device removal in pci_bridge_d3_update()
PCI: Don't acquire ref on parent in pci_bridge_d3_update()
USB: UHCI: report non-PME wakeup signalling for Intel hardware
PCI: Check for PME in targeted sleep state
The acpi_get_rc_resources() is used to get the RC register address that can
not be described in MCFG. It takes the _HID & segment to look for and
outputs the RC address resource. Use PNP0C02 devices to describe such RC
address resource. Use _UID to match segment to tell which root bus the
PNP0C02 resource belongs to.
[bhelgaas: add dev argument, wrap in #ifdef CONFIG_PCI_QUIRKS]
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We're about to add runtime PM of hotplug ports, but we need to restrict it
to ports that are handled natively by the OS: If they're handled by the
firmware (which is the case for Thunderbolt on non-Macs), things would
break if the OS put the ports into D3hot behind the firmware's back.
To determine if a hotplug port is handled natively, one has to walk up from
the port to the root bridge and check the cached _OSC Control Field for the
value of the "PCI Express Native Hot Plug control" bit. There's already a
function to do that, device_is_managed_by_native_pciehp(), but it's private
to drivers/pci/hotplug/acpiphp_glue.c and only compiled in if
CONFIG_HOTPLUG_PCI_ACPI is enabled.
Make it public and move it to drivers/pci/pci-acpi.c, so that it is
available in the more general CONFIG_ACPI case.
The function contains a check if the device in question is a hotplug port
and returns false if it's not. The caller we're going to add doesn't need
this as it only calls the function if it actually *is* a hotplug port.
Move the check out of the function into the single existing caller.
Rename it to pciehp_is_native() and add some kerneldoc and polish.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Usually the most accurate way to determine a PCI device's power state is to
read its PM Control & Status Register. There are two cases however when
this is not an option: If the device doesn't have the PM capability at
all, or if it is in D3cold (in which case its config space is
inaccessible).
In both cases, we can alternatively query the platform firmware for its
opinion on the device's power state. To facilitate this, augment struct
pci_platform_pm_ops with a ->get_power callback and implement it for
acpi_pci_platform_pm (the only pci_platform_pm_ops existing so far).
It is used by a forthcoming commit to let pci_update_current_state()
recognize D3cold.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Add a debugfs-based interface for interacting with the ACPICA's
AML debugger introduced in the previous cycle and a new user
space tool for that, fix some bugs related to the AML debugger
and clean up the code in question (Lv Zheng, Dan Carpenter,
Colin Ian King, Markus Elfring).
- Update ACPICA to upstream revision 20151218 including a number
of fixes and cleanups in the ACPICA core (Bob Moore, Lv Zheng,
Labbe Corentin, Prarit Bhargava, Colin Ian King, David E Box,
Rafael Wysocki).
In particular, the previously added erroneous support for the
_SUB object is dropped, the concatenate operator will support
all ACPI objects now, the Debug Object handling is improved,
the SuperName handling of parameters being control methods is
fixed, the ObjectType operator handling is updated to follow
ACPI 5.0A and the handling of CondRefOf and RefOf is updated
accordingly, module-level code will be executed after loading
each ACPI table now (instead of being run once after all tables
containing AML have been loaded), the Operation Region handlers
management is updated to fix some reported problems and a the
ACPICA code in the kernel is more in line with the upstream
now.
- Update the ACPI backlight driver to provide information on
whether or not it will generate key-presses for brightness
change hotkeys and update some platform drivers (dell-wmi,
thinkpad_acpi) to use that information to avoid sending double
key-events to users pace for these, add new ACPI backlight
quirks (Hans de Goede, Aaron Lu, Adrien Schildknecht).
- Improve the ACPI handling of interrupt GPIOs (Christophe Ricard).
- Fix the handling of the list of device IDs of device objects
found in the ACPI namespace and add a helper for checking if
there is a device object for a given device ID (Lukas Wunner).
- Change the logic in the ACPI namespace scanning code to create
struct acpi_device objects for all ACPI device objects found in
the namespace even if _STA fails for them which helps to avoid
device enumeration problems on Microsoft Surface 3 (Aaron Lu).
- Add support for the APM X-Gene ACPI I2C device to the ACPI
driver for AMD SoCs (Loc Ho).
- Fix the long-standing issue with the DMA controller on Intel
SoCs where ACPI tables have no power management support for
the DMA controller itself, but it can be powered off automatically
when the last (other) device on the SoC is powered off via ACPI
and clean up the ACPI driver for Intel SoCs (acpi-lpss) after
previous attempts to fix that problem (Andy Shevchenko).
- Assorted ACPI fixes and cleanups (Andy Lutomirski, Colin Ian King,
Javier Martinez Canillas, Ken Xue, Mathias Krause, Rafael Wysocki,
Sinan Kaya).
- Update the device properties framework for better handling of
built-in properties, add support for built-in properties to
the platform bus type, update the MFD subsystem's handling
of device properties and add support for passing default
configuration data as device properties to the intel-lpss MFD
drivers, convert the designware I2C driver to use the unified
device properties API and add a fallback mechanism for using
default built-in properties if the platform firmware fails
to provide the properties as expected by drivers (Andy Shevchenko,
Mika Westerberg, Heikki Krogerus, Andrew Morton).
- Add new Device Tree bindings to the Operating Performance Points
(OPP) framework and update the exynos4412 DT binding accordingly,
introduce debugfs support for the OPP framework (Viresh Kumar,
Bartlomiej Zolnierkiewicz).
- Migrate the mt8173 cpufreq driver to the new OPP bindings
(Pi-Cheng Chen).
- Update the cpufreq core to make the handling of governors
more efficient, especially on systems where policy objects
are shared between multiple CPUs (Viresh Kumar, Rafael Wysocki).
- Fix cpufreq governor handling on configurations with
CONFIG_HZ_PERIODIC set (Chen Yu).
- Clean up the cpufreq core code related to the boost sysfs knob
support and update the ACPI cpufreq driver accordingly (Rafael
Wysocki).
- Add a new cpufreq driver for ST platforms and corresponding
Device Tree bindings (Lee Jones).
- Update the intel_pstate driver to allow the P-state selection
algorithm used by it to depend on the CPU ID of the processor it
is running on, make it use a special P-state selection algorithm
(with an IO wait time compensation tweak) on Atom CPUs based on
the Airmont and Silvermont cores so as to reduce their energy
consumption and improve intel_pstate documentation (Philippe
Longepe, Srinivas Pandruvada).
- Update the cpufreq-dt driver to support registering cooling
devices that use the (P * V^2 * f) dynamic power draw formula
where V is the voltage, f is the frequency and P is a constant
coefficient provided by Device Tree and update the arm_big_little
cpufreq driver to use that support (Punit Agrawal).
- Assorted cpufreq driver (cpufreq-dt, qoriq, pcc-cpufreq,
blackfin-cpufreq) updates (Andrzej Hajda, Hongtao Jia,
Jacob Tanenbaum, Markus Elfring).
- cpuidle core tweaks related to polling and measured_us
calculation (Rik van Riel).
- Removal of modularity from a few cpuidle drivers (clps711x,
ux500, exynos) that cannot be built as modules in practice
(Paul Gortmaker).
- PM core update to prevent devices from being probed during
system suspend/resume which is generally problematic and may
lead to inconsistent behavior (Grygorii Strashko).
- Assorted updates of the PM core and related code (Julia Lawall,
Manuel Pégourié-Gonnard, Maruthi Bayyavarapu, Rafael Wysocki,
Ulf Hansson).
- PNP bus type updates (Christophe Le Roy, Heiner Kallweit).
- PCI PM code cleanups (Jarkko Nikula, Julia Lawall).
- cpupower tool updates (Jacob Tanenbaum, Thomas Renninger).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=OlYA
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.5-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull oower management and ACPI updates from Rafael Wysocki:
"As far as the number of commits goes, ACPICA takes the lead this time,
followed by cpufreq and the device properties framework changes.
The most significant new feature is the debugfs-based interface to the
ACPICA's AML debugger added in the previous cycle and a new user space
tool for accessing it.
On the cpufreq front, the core is updated to handle governors more
efficiently, particularly on systems where a single cpufreq policy
object is shared between multiple CPUs, and there are quite a few
changes in drivers (intel_pstate, cpufreq-dt etc).
The device properties framework is updated to handle built-in (ie
included in the kernel itself) device properties better, among other
things by adding a fallback mechanism that will allow drivers to
provide default properties to be used in case the plaform firmware
doesn't provide the properties expected by them.
The Operating Performance Points (OPP) framework gets new DT bindings
and debugfs support.
A new cpufreq driver for ST platforms is added and the ACPI driver for
AMD SoCs will now support the APM X-Gene ACPI I2C device.
The rest is mostly fixes and cleanups all over.
Specifics:
- Add a debugfs-based interface for interacting with the ACPICA's AML
debugger introduced in the previous cycle and a new user space tool
for that, fix some bugs related to the AML debugger and clean up
the code in question (Lv Zheng, Dan Carpenter, Colin Ian King,
Markus Elfring).
- Update ACPICA to upstream revision 20151218 including a number of
fixes and cleanups in the ACPICA core (Bob Moore, Lv Zheng, Labbe
Corentin, Prarit Bhargava, Colin Ian King, David E Box, Rafael
Wysocki).
In particular, the previously added erroneous support for the _SUB
object is dropped, the concatenate operator will support all ACPI
objects now, the Debug Object handling is improved, the SuperName
handling of parameters being control methods is fixed, the
ObjectType operator handling is updated to follow ACPI 5.0A and the
handling of CondRefOf and RefOf is updated accordingly, module-
level code will be executed after loading each ACPI table now
(instead of being run once after all tables containing AML have
been loaded), the Operation Region handlers management is updated
to fix some reported problems and a the ACPICA code in the kernel
is more in line with the upstream now.
- Update the ACPI backlight driver to provide information on whether
or not it will generate key-presses for brightness change hotkeys
and update some platform drivers (dell-wmi, thinkpad_acpi) to use
that information to avoid sending double key-events to users pace
for these, add new ACPI backlight quirks (Hans de Goede, Aaron Lu,
Adrien Schildknecht).
- Improve the ACPI handling of interrupt GPIOs (Christophe Ricard).
- Fix the handling of the list of device IDs of device objects found
in the ACPI namespace and add a helper for checking if there is a
device object for a given device ID (Lukas Wunner).
- Change the logic in the ACPI namespace scanning code to create
struct acpi_device objects for all ACPI device objects found in the
namespace even if _STA fails for them which helps to avoid device
enumeration problems on Microsoft Surface 3 (Aaron Lu).
- Add support for the APM X-Gene ACPI I2C device to the ACPI driver
for AMD SoCs (Loc Ho).
- Fix the long-standing issue with the DMA controller on Intel SoCs
where ACPI tables have no power management support for the DMA
controller itself, but it can be powered off automatically when the
last (other) device on the SoC is powered off via ACPI and clean up
the ACPI driver for Intel SoCs (acpi-lpss) after previous attempts
to fix that problem (Andy Shevchenko).
- Assorted ACPI fixes and cleanups (Andy Lutomirski, Colin Ian King,
Javier Martinez Canillas, Ken Xue, Mathias Krause, Rafael Wysocki,
Sinan Kaya).
- Update the device properties framework for better handling of
built-in properties, add support for built-in properties to the
platform bus type, update the MFD subsystem's handling of device
properties and add support for passing default configuration data
as device properties to the intel-lpss MFD drivers, convert the
designware I2C driver to use the unified device properties API and
add a fallback mechanism for using default built-in properties if
the platform firmware fails to provide the properties as expected
by drivers (Andy Shevchenko, Mika Westerberg, Heikki Krogerus,
Andrew Morton).
- Add new Device Tree bindings to the Operating Performance Points
(OPP) framework and update the exynos4412 DT binding accordingly,
introduce debugfs support for the OPP framework (Viresh Kumar,
Bartlomiej Zolnierkiewicz).
- Migrate the mt8173 cpufreq driver to the new OPP bindings (Pi-Cheng
Chen).
- Update the cpufreq core to make the handling of governors more
efficient, especially on systems where policy objects are shared
between multiple CPUs (Viresh Kumar, Rafael Wysocki).
- Fix cpufreq governor handling on configurations with
CONFIG_HZ_PERIODIC set (Chen Yu).
- Clean up the cpufreq core code related to the boost sysfs knob
support and update the ACPI cpufreq driver accordingly (Rafael
Wysocki).
- Add a new cpufreq driver for ST platforms and corresponding Device
Tree bindings (Lee Jones).
- Update the intel_pstate driver to allow the P-state selection
algorithm used by it to depend on the CPU ID of the processor it is
running on, make it use a special P-state selection algorithm (with
an IO wait time compensation tweak) on Atom CPUs based on the
Airmont and Silvermont cores so as to reduce their energy
consumption and improve intel_pstate documentation (Philippe
Longepe, Srinivas Pandruvada).
- Update the cpufreq-dt driver to support registering cooling devices
that use the (P * V^2 * f) dynamic power draw formula where V is
the voltage, f is the frequency and P is a constant coefficient
provided by Device Tree and update the arm_big_little cpufreq
driver to use that support (Punit Agrawal).
- Assorted cpufreq driver (cpufreq-dt, qoriq, pcc-cpufreq,
blackfin-cpufreq) updates (Andrzej Hajda, Hongtao Jia, Jacob
Tanenbaum, Markus Elfring).
- cpuidle core tweaks related to polling and measured_us calculation
(Rik van Riel).
- Removal of modularity from a few cpuidle drivers (clps711x, ux500,
exynos) that cannot be built as modules in practice (Paul
Gortmaker).
- PM core update to prevent devices from being probed during system
suspend/resume which is generally problematic and may lead to
inconsistent behavior (Grygorii Strashko).
- Assorted updates of the PM core and related code (Julia Lawall,
Manuel Pégourié-Gonnard, Maruthi Bayyavarapu, Rafael Wysocki, Ulf
Hansson).
- PNP bus type updates (Christophe Le Roy, Heiner Kallweit).
- PCI PM code cleanups (Jarkko Nikula, Julia Lawall).
- cpupower tool updates (Jacob Tanenbaum, Thomas Renninger)"
* tag 'pm+acpi-4.5-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (177 commits)
PM / clk: don't leave clocks enabled when driver not bound
i2c: dw: Add APM X-Gene ACPI I2C device support
ACPI / APD: Add APM X-Gene ACPI I2C device support
ACPI / LPSS: change 'does not have' to 'has' in comment
Revert "dmaengine: dw: platform: provide platform data for Intel"
dmaengine: dw: return immediately from IRQ when DMA isn't in use
dmaengine: dw: platform: power on device on shutdown
ACPI / LPSS: override power state for LPSS DMA device
PM / OPP: Use snprintf() instead of sprintf()
Documentation: cpufreq: intel_pstate: enhance documentation
ACPI, PCI, irq: remove redundant check for null string pointer
ACPI / video: driver must be registered before checking for keypresses
cpufreq-dt: fix handling regulator_get_voltage() result
cpufreq: governor: Fix negative idle_time when configured with CONFIG_HZ_PERIODIC
PM / sleep: Add support for read-only sysfs attributes
ACPI: Fix white space in a structure definition
ACPI / SBS: fix inconsistent indenting inside if statement
PNP: respect PNP_DRIVER_RES_DO_NOT_CHANGE when detaching
ACPI / PNP: constify device IDs
ACPI / PCI: Simplify acpi_penalize_isa_irq()
...
This patch introduces pci_msi_register_fwnode_provider() for irqchip
to register a callback, to provide a way to determine appropriate MSI
domain for a pci device.
It also introduces pci_host_bridge_acpi_msi_domain(), which returns
the MSI domain of the specified PCI host bridge with DOMAIN_BUS_PCI_MSI
bus token. Then, it is assigned to pci device.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The pci_platform_pm_ops structure is never modified, so declare it as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The function takes ACPI handle, not the device itself. Fix the
comment
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The ACPI 6 specification has made some changes in the device power
management area. In particular:
* The D3hot power state is now supposed to be always available
(instead of D3cold) and D3cold is only regarded as valid if the
_PR3 object is present for the given device.
* The required ordering of transitions into power states deeper than
D0 is now such that for a transition into state Dx the _PSx method
is supposed to be executed first, if present, and the states of
the power resources the device depends on are supposed to be
changed after that.
* It is now explicitly forbidden to transition devices from
lower-power (deeper) into higher-power (shallower) power states
other than D0.
Those changes have been made so the specification reflects the
Windows' device power management code that the vast majority of
systems using ACPI is validated against.
To avoid artificial differences in ACPI device power management
between Windows and Linux, modify the ACPI device power management
code to follow the new specification. Add comments explaining the
code flow in some unclear places.
This only may affect some real corner cases in which the OS behavior
expected by the firmware is different from the Windows one, but that's
quite unlikely. The transition ordering change affects transitions
to D1 and D2 which are rarely used (if at all) and into D3hot and
D3cold for devices actually having _PR3, but those are likely to
be validated against Windows anyway. The other changes may affect
code calling acpi_device_get_power() or acpi_device_update_power()
where ACPI_STATE_D3_HOT may be returned instead of ACPI_STATE_D3_COLD
(that's why the ACPI fan driver needs to be updated too) and since
transitions into ACPI_STATE_D3_HOT may remove power now, it is better
to avoid this one in acpi_pm_device_sleep_state() if the "no power
off" PM QoS flag is set.
The only existing user of acpi_device_can_poweroff() really cares
about the case when _PR3 is present, so the change in that function
should not cause any problems to happen too.
A plus is that PCI_D3hot can be mapped to ACPI_STATE_D3_HOT
now and the compatibility with older systems should be covered
automatically.
In any case, if any real problems result from this, it still will
be better to follow the Windows' behavior (which now is reflected
by the specification too) in general and handle the cases when it
doesn't work via quirks.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The PCI "ACPI additions for FW latency optimizations" ECN (link below)
defines two functions in the PCI _DSM:
Function 8, "Reset Delay," applies to the entire hierarchy below a PCI
host bridge. If it returns one, the OS may assume that all devices in
the hierarchy have already completed power-on reset delays.
Function 9, "Device Readiness Durations," applies only to the object
where it is located. It returns delay durations required after various
events if the device requires less time than the spec requires. Delays
from this function take precedence over the Reset Delay function.
Add support for Reset Delay and part of Device Readiness Durations.
[bhelgaas: changelog, comments]
Link: https://www.pcisig.com/specifications/conventional/pci_firmware/ECN_fw_latency_optimization_final.pdf
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI Firmware Specification, r3.0, sec 4.6.4.1.3, defines a single UUID
for an ACPI _DSM method to provide device-specific control functions. This
_DSM method support several functions, including PCI Express Slot
Information, PCI Express Slot Number, PCI Bus Capabilities, etc.
Move the UUID definition from pci/pci-label.c, where it could be used only
for one function, to pci/pci-acpi.c where it can be shared for all these
functions.
[bhelgaas: changelog]
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Booting a v3.18 or newer Xen domU kernel with PCI devices passed through
results in an oops (this is a 32-bit 3.13.11 dom0 with a 64-bit 4.4.0
hypervisor and 32-bit domU):
BUG: unable to handle kernel paging request at 0030303e
IP: [<c06ed0e6>] acpi_ns_validate_handle+0x12/0x1a
Call Trace:
[<c06eda4d>] ? acpi_evaluate_object+0x31/0x1fc
[<c06b78e1>] ? pci_get_hp_params+0x111/0x4e0
[<c0407bc7>] ? xen_force_evtchn_callback+0x17/0x30
[<c04085fb>] ? xen_restore_fl_direct_reloc+0x4/0x4
[<c0699d34>] ? pci_device_add+0x24/0x450
Don't look for ACPI configuration information if ACPI has been disabled.
I don't think this is the best fix, because we can boot plain Linux (no
Xen) with "acpi=off", and we don't need this check in pci_get_hp_params().
There should be a better fix that would make Xen domU work the same way.
The domU kernel has ACPI support but it has no AML. There should be a way
to initialize the ACPI data structures so things fail gracefully rather
than oopsing. This is an interim fix to address the regression.
Fixes: 6cd33649fa ("PCI: Add pci_configure_device() during enumeration")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=96301
Reported-by: Michael D Labriola <mlabriol@gdeb.com>
Tested-by: Michael D Labriola <mlabriol@gdeb.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.18+
Commit f25c0ae2b4 (ACPI / PM: Avoid resuming devices in ACPI PM
domain during system suspend) modified the ACPI PM domain's system
suspend callbacks to allow devices attached to it to be left in the
runtime-suspended state during system suspend so as to optimize
the suspend process.
This was based on the general mechanism introduced by commit
aae4518b31 (PM / sleep: Mechanism to avoid resuming runtime-suspended
devices unnecessarily).
Extend that approach to PCI devices by modifying the PCI bus type's
->prepare callback to return 1 for devices that are runtime-suspended
when it is being executed and that are in a suitable power state and
need not be resumed going forward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The functions pci_dev_put(), pci_pme_wakeup_bus(), and put_device() return
immediately if their argument is NULL. Thus the test before the call is
not needed.
Remove these unnecessary tests.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move code around to put all the ACPI power management stuff together and
all the pieces related to ACPI methods (_CBA, _HPP, _HPX) together.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move pci_get_hp_params() and related functions from
drivers/pci/hotplug/acpi_pcihp.c to drivers/pci/pci-acpi.c.
Previously, pci_get_hp_params() was used only by hotplug drivers. But
future changes will move this into the normal device enumeration process,
so it will be used even when CONFIG_HOTPLUG_PCI is not set.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The ACPI_HANDLE() macro evaluates ACPI_COMPANION() internally to
return the handle of the device's ACPI companion, so it is much
more straightforward and efficient to use ACPI_COMPANION()
directly to obtain the device's ACPI companion object instead of
using ACPI_HANDLE() and acpi_bus_get_device() on the returned
handle for the same thing.
Use ACPI_COMPANION() instead of ACPI_HANDLE() in the PCI ACPI support
code.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since ACPI wakeup GPEs are going to be enabled during system suspend
as well as for runtime wakeup by a subsequent patch and the same
notify handlers will be used in both cases, rework the ACPI device
wakeup notification framework so that the part specific to physical
devices is always run asynchronously from the PM workqueue. This
prevents runtime resume callbacks for those devices from being
run during system suspend and resume which may not be appropriate,
among other things.
Also make ACPI device wakeup notification handling a bit more robust
agaist subsequent removal of ACPI device objects, whould that ever
happen, and create a wakeup source object for each ACPI device
configured for wakeup so that wakeup notifications for those
devices can wake up the system from the "freeze" sleep state.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use pci_is_bridge() to simplify code. No functional change.
Requires: 326c1cdae7 PCI: Rename pci_is_bridge() to pci_has_subordinate()
Requires: 1c86438c94 PCI: Add new pci_is_bridge() interface
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- ACPI core changes to make it create a struct acpi_device object for every
device represented in the ACPI tables during all namespace scans regardless
of the current status of that device. In accordance with this, ACPI hotplug
operations will not delete those objects, unless the underlying ACPI tables
go away.
- On top of the above, new sysfs attribute for ACPI device objects allowing
user space to check device status by triggering the execution of _STA for
its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating the
PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the code
"glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for the
DBG2 and PCCT tables to ACPICA, fixes some bugs and improves debug
facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization earlier.
That should allow us to use ACPI during the timekeeping initialization
and possibly to simplify the EFI initialization too. From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over from
Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in drivers
that uses _DSM to execute it via the new helper. From Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun Guo,
Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava, Rashika Kheria,
Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support, from
Dirk Brandewie and intel_pstate documentation from Ramkumar Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John Tobias,
Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC disabled
during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente Kurusa,
Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a cpupower
tool cleanup from One Thousand Gnomes.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=dRf6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"As far as the number of commits goes, the top spot belongs to ACPI
this time with cpufreq in the second position and a handful of PM
core, PNP and cpuidle updates. They are fixes and cleanups mostly, as
usual, with a couple of new features in the mix.
The most visible change is probably that we will create struct
acpi_device objects (visible in sysfs) for all devices represented in
the ACPI tables regardless of their status and there will be a new
sysfs attribute under those objects allowing user space to check that
status via _STA.
Consequently, ACPI device eject or generally hot-removal will not
delete those objects, unless the table containing the corresponding
namespace nodes is unloaded, which is extremely rare. Also ACPI
container hotplug will be handled quite a bit differently and cpufreq
will support CPU boost ("turbo") generically and not only in the
acpi-cpufreq driver.
Specifics:
- ACPI core changes to make it create a struct acpi_device object for
every device represented in the ACPI tables during all namespace
scans regardless of the current status of that device. In
accordance with this, ACPI hotplug operations will not delete those
objects, unless the underlying ACPI tables go away.
- On top of the above, new sysfs attribute for ACPI device objects
allowing user space to check device status by triggering the
execution of _STA for its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating
the PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the
code "glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for
the DBG2 and PCCT tables to ACPICA, fixes some bugs and improves
debug facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization
earlier. That should allow us to use ACPI during the timekeeping
initialization and possibly to simplify the EFI initialization too.
From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over
from Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in
drivers that uses _DSM to execute it via the new helper. From
Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun
Guo, Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava,
Rashika Kheria, Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support,
from Dirk Brandewie and intel_pstate documentation from Ramkumar
Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz
Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark
Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John
Tobias, Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh
Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC
disabled during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf
Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente
Kurusa, Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a
cpupower tool cleanup from One Thousand Gnomes"
* tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (153 commits)
thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412)
cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ
Documentation: cpufreq / boost: Update BOOST documentation
cpufreq: exynos: Extend Exynos cpufreq driver to support boost
cpufreq / boost: Kconfig: Support for software-managed BOOST
acpi-cpufreq: Adjust the code to use the common boost attribute
cpufreq: Add boost frequency support in core
intel_pstate: Add trace point to report internal state.
cpufreq: introduce cpufreq_generic_get() routine
ARM: SA1100: Create dummy clk_get_rate() to avoid build failures
cpufreq: stats: create sysfs entries when cpufreq_stats is a module
cpufreq: stats: free table and remove sysfs entry in a single routine
cpufreq: stats: remove hotplug notifiers
cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly
cpufreq: speedstep: remove unused speedstep_get_state
platform: introduce OF style 'modalias' support for platform bus
PM / tools: new tool for suspend/resume performance optimization
ACPI: fix module autoloading for ACPI enumerated devices
ACPI: add module autoloading support for ACPI enumerated devices
ACPI: fix create_modalias() return value handling
...
* acpi-cleanup: (22 commits)
ACPI / tables: Return proper error codes from acpi_table_parse() and fix comment.
ACPI / tables: Check if id is NULL in acpi_table_parse()
ACPI / proc: Include appropriate header file in proc.c
ACPI / EC: Remove unused functions and add prototype declaration in internal.h
ACPI / dock: Include appropriate header file in dock.c
ACPI / PCI: Include appropriate header file in pci_link.c
ACPI / PCI: Include appropriate header file in pci_slot.c
ACPI / EC: Mark the function acpi_ec_add_debugfs() as static in ec_sys.c
ACPI / NVS: Include appropriate header file in nvs.c
ACPI / OSL: Mark the function acpi_table_checksum() as static
ACPI / processor: initialize a variable to silence compiler warning
ACPI / processor: use ACPI_COMPANION() to get ACPI device
ACPI: correct minor typos
ACPI / sleep: Drop redundant acpi_disabled check
ACPI / dock: Drop redundant acpi_disabled check
ACPI / table: Replace '1' with specific error return values
ACPI: remove trailing whitespace
ACPI / IBFT: Fix incorrect <acpi/acpi.h> inclusion in iSCSI boot firmware module
ACPI / i915: Fix incorrect <acpi/acpi.h> inclusions via <linux/acpi_io.h>
SFI / ACPI: Fix warnings reported during builds with W=1
...
Conflicts:
drivers/acpi/nvs.c
drivers/hwmon/asus_atk0110.c
It turns out that some BIOSes don't report wakeup GPEs through
_PRW, but use them for signaling wakeup anyway, which causes GPE
storms to occur on some systems after resume from system suspend.
This issue has been uncovered by commit d2e5f0c16a (ACPI / PCI:
Rework the setup and cleanup of device wakeup) during the 3.9
development cycle.
Work around the problem by installing wakeup notify handlers for all
PCI devices with ACPI support (i.e. having ACPI companions) regardless
of whether or not the BIOS reports ACPI wakeup support for them. The
presence of the wakeup notify handlers alone is not harmful in any
way if there are no events for them to handle (they are simply never
executed then), but on some systems they are needed to take care of
spurious events.
Fixes: d2e5f0c16a (ACPI / PCI: Rework the setup and cleanup of device wakeup)
References: https://bugzilla.kernel.org/show_bug.cgi?id=63021
Reported-and-tested-by: Agustin Barto <abarto@gmail.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use dev_is_pci() instead of checking bus type directly.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Replace the .find_device function pointer in struct acpi_bus_type
with a new one, .find_companion, that is supposed to point to a
function returning struct acpi_device pointer (instead of an int)
and takes one argument (instead of two). This way the role of
this callback is more clear and the implementation of it can
be more straightforward.
Update all of the users of struct acpi_bus_type (PCI, PNP/ACPI and
USB) to reflect the structure change.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Lan Tianyu <tianyu.lan@intel.com> # for USB/ACPI
It is much more efficient to use acpi_find_child_device()
for child devices lookup in acpi_pci_find_device() and pass
ACPI_COMPANION(dev->parent) to it directly instead of obtaining
ACPI_HANDLE() of ACPI_COMPANION(dev->parent) and passing it to
acpi_find_child() which has to run acpi_bus_get_device() to
obtain ACPI_COMPANION(dev->parent) from that again.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.
First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.
Second, there are ordering dependencies between those files that always
have to be met. Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there. And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds. That also is taken care of including
<linux/acpi.h> as appropriate.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since DEVICE_ACPI_HANDLE() is now literally identical to
ACPI_HANDLE(), replace it with the latter everywhere and drop its
definition from include/acpi.h.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix whitespace, capitalization, and spelling errors. No functional change.
I know "busses" is not an error, but "buses" was more common, so I used it
consistently.
Signed-off-by: Marta Rybczynska <rybczynska@gmail.com> (pci_reset_bridge_secondary_bus())
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_has_method() is a new ACPI API introduced to check
the existence of an ACPI control method.
It can be used to replace acpi_get_handle() in the case that
1. the calling function doesn't need the ACPI handle of the control method.
and
2. the calling function doesn't care the reason why the method is unavailable.
Convert acpi_get_handle() to acpi_has_method()
in drivers/pci/pci-acpi.c in this patch.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
CC: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 448bd85 (PCI/PM: add PCIe runtime D3cold support) added a
piece of code to pci_acpi_wake_dev() causing that function to behave
in a special way for devices in D3cold (so that their configuration
registers are not accessed before those devices are resumed).
However, it didn't take the clearing of the pme_poll flag into
account. That has to be done for all devices, even if they are in
D3cold, or pci_pme_list_scan() will not know that wakeup has been
signaled for the device and will poll its PME Status bit
unnecessarily.
Fix the problem by moving the clearing of the pme_poll flag in
pci_acpi_wake_dev() before the code introduced by commit 448bd85.
Reported-and-tested-by: David E. Box <david.e.box@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: 3.6+ <stable@vger.kernel.org> # 3.6+
* acpi-pci-hotplug: (34 commits)
ACPI / PM: Hold acpi_scan_lock over system PM transitions
ACPI / hotplug / PCI: Fix NULL pointer dereference in cleanup_bridge()
PCI / ACPI: Use dev_dbg() instead of dev_info() in acpi_pci_set_power_state()
ACPI / hotplug / PCI: Get rid of check_sub_bridges()
ACPI / hotplug / PCI: Clean up bridge_mutex usage
ACPI / hotplug / PCI: Redefine enable_device() and disable_device()
ACPI / hotplug / PCI: Sanitize acpiphp_get_(latch)|(adapter)_status()
ACPI / hotplug / PCI: Get rid of unused constants in acpiphp.h
ACPI / hotplug / PCI: Check for new devices on enabled slots
ACPI / hotplug / PCI: Allow slots without new devices to be rescanned
ACPI / hotplug / PCI: Do not check SLOT_ENABLED in enable_device()
ACPI / hotplug / PCI: Do not exectute _PS0 and _PS3 directly
ACPI / hotplug / PCI: Do not queue up event handling work items in vain
ACPI / hotplug / PCI: Consolidate slot disabling and ejecting
ACPI / hotplug / PCI: Drop redundant checks from check_hotplug_bridge()
ACPI / hotplug / PCI: Rework namespace scanning and trimming routines
ACPI / hotplug / PCI: Store parent in functions and bus in slots
ACPI / hotplug / PCI: Drop handle field from struct acpiphp_bridge
ACPI / hotplug / PCI: Drop handle field from struct acpiphp_func
ACPI / hotplug / PCI: Embed function struct into struct acpiphp_context
...
In theory, under a given ACPI namespace node there should be only
one child device object with _ADR whose value matches a given bus
address exactly. In practice, however, there are systems in which
multiple child device objects under a given parent have _ADR matching
exactly the same address. In those cases we use _STA to determine
which of the multiple matching devices is enabled, since some systems
are known to indicate which ACPI device object to associate with the
given physical (usually PCI) device this way.
Unfortunately, as it turns out, there are systems in which many
device objects under the same parent have _ADR matching exactly the
same bus address and none of them has _STA, in which case they all
should be regarded as enabled according to the spec. Still, if
those device objects are supposed to represent bridges (e.g. this
is the case for device objects corresponding to PCIe ports), we can
try harder and skip the ones that have no child device objects in the
ACPI namespace. With luck, we can avoid using device objects that we
are not expected to use this way.
Although this only works for bridges whose children also have ACPI
namespace representation, it is sufficient to address graphics
adapter detection issues on some systems, so rework the code finding
a matching device ACPI handle for a given bus address to implement
this idea.
Introduce a new function, acpi_find_child(), taking three arguments:
the ACPI handle of the device's parent, a bus address suitable for
the device's bus type and a bool indicating if the device is a
bridge and make it work as outlined above. Reimplement the function
currently used for this purpose, acpi_get_child(), as a call to
acpi_find_child() with the last argument set to 'false' and make
the PCI subsystem use acpi_find_child() with the bridge information
passed as the last argument to it. [Lan Tianyu notices that it is
not sufficient to use pci_is_bridge() for that, because the device's
subordinate pointer hasn't been set yet at this point, so use
hdr_type instead.]
This change fixes a regression introduced inadvertently by commit
33f767d (ACPI: Rework acpi_get_child() to be more efficient) which
overlooked the fact that for acpi_walk_namespace() "post-order" means
"after all children have been visited" rather than "on the way back",
so for device objects without children and for namespace walks of
depth 1, as in the acpi_get_child() case, the "post-order" callbacks
ordering is actually the same as the ordering of "pre-order" ones.
Since that commit changed the namespace walk in acpi_get_child() to
terminate after finding the first matching object instead of going
through all of them and returning the last one, it effectively
changed the result returned by that function in some rare cases and
that led to problems (the switch from a "pre-order" to a "post-order"
callback was supposed to prevent that from happening, but it was
ineffective).
As it turns out, the systems where the change made by commit
33f767d actually matters are those where there are multiple ACPI
device objects representing the same PCIe port (which effectively
is a bridge). Moreover, only one of them, and the one we are
expected to use, has child device objects in the ACPI namespace,
so the regression can be addressed as described above.
References: https://bugzilla.kernel.org/show_bug.cgi?id=60561
Reported-by: Peter Wu <lekensteyn@gmail.com>
Tested-by: Vladimir Lalov <mail@vlalov.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: 3.9+ <stable@vger.kernel.org> # 3.9+
acpi_pci_set_power_state() uses dev_info() to print diagnostic
messages regarding ACPI power state changes of devices, but that
results in too much not really interesting output into the kernel
log in some cases.
For this reason, change it to use dev_dbg() instead and prevent
kernel log from being spammed.
[rjw: Changelog]
References: https://bugzilla.kernel.org/show_bug.cgi?id=60636
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since acpi_pci_slot_enumerate() and acpiphp_enumerate_slots() can get
the ACPI device handle they need from bus->bridge, it is not
necessary to pass that handle to them as an argument.
Drop the second argument of acpi_pci_slot_enumerate() and
acpiphp_enumerate_slots(), rework them to obtain the ACPI handle
from bus->bridge and make acpi_pci_add_bus() and
acpi_pci_remove_bus() entirely symmetrical.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Make acpi_pci_set_power_state() print the name of the ACPI device
power state the device has been actually put into instead of printing
the name of the requested PCI device power state, which need not be
the same.
[bhelgaas: use ACPI_STATE_D3_COLD (ACPI_STATE_D3 == ACPI_STATE_D3_COLD)]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rafael J. Wysocki