We allocate only 4 bytes here "sizeof(int)" instead of WF_MSAMPLE_BYTES
(259) which was intended.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
msnd_pinnacle.c is used for both snd-msnd-pinnacle and
snd-msnd-classic drivers, and both should have different driver
names. Using the same driver name results in the sysfs warning for
duplicated entries like
kobject: 'msnd-pinnacle.7' (cec33408): kobject_release, parent (null) (delayed)
kobject: 'msnd-pinnacle' (cecd4980): kobject_release, parent cf3ad9b0 (delayed)
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at fs/sysfs/dir.c:486 sysfs_warn_dup+0x7d/0xa0()
sysfs: cannot create duplicate filename '/bus/isa/drivers/msnd-pinnacle'
......
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is a 2 byte hole after "info.func_nr" so we could leak unitialized
stack information to userspace.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just add an ifdef CONFIG_PM to shut up the warnings:
sound/isa/cmi8328.c:129:13: warning: ‘snd_cmi8328_cfg_save’ defined but not used [-Wunused-function]
sound/isa/cmi8328.c:136:13: warning: ‘snd_cmi8328_cfg_restore’ defined but not used [-Wunused-function]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent commit to delay the release of kobject triggered NULL
dereferences of opti9xx drivers. The cause is that all
snd-opti92x-ad1848, snd-opti92x-cs4231 and snd-opti93x drivers
register the PnP card driver with the very same name, and also
snd-opti92x-ad1848 and -cs4231 drivers register the ISA driver with
the same name, too. When these drivers are built in, quick
"register-release-and-re-register" actions occur, and this results in
Oops because of the same name is assigned to the kobject.
The fix is simply to assign individual names. As a bonus, by using
KBUILD_MODNAME, the patch reduces more lines than it adds.
The fix is based on the suggestion by Russell King.
Reported-and-tested-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no need to pass constants via stack. The width may be explicitly
specified in the format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similarly like the previous commit for PCI drivers, remove
dev_set_drvdata(NULL) and pnp_set_drvdata(NULL) calls in ISA drivers
now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the leftover __devinit* in comments.
They have been commented out because they couldn't fit with __dev*
although they should have matched.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_miro_probe is a static function that is only called twice in the file
that defines it. At each call site, its argument is freed using
snd_card_free. Thus, there is no need for snd_miro_probe to call
snd_card_free on its argument on any of its error exit paths.
Because snd_card_free both reads the fields of its argument and kfrees its
argments, the results of the second snd_card_free should be unpredictable.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f,free,a;
parameter list[n] ps;
type T;
expression e;
@@
f(ps,T a,...) {
... when any
when != a = e
if(...) { ... free(a); ... return ...; }
... when any
}
@@
identifier r.f,r.free;
expression x,a;
expression list[r.n] xs;
@@
* x = f(xs,a,...);
if (...) { ... free(a); ... return ...; }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r1@
statement S;
position p,p1;
@@
S@p1;@p
@script:python r2@
p << r1.p;
p1 << r1.p1;
@@
if p[0].line != p1[0].line_end:
cocci.include_match(False)
@@
position r1.p;
@@
-;@p
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
v2: Fixed result still wrong in the case of 512 KiB DRAM. Oops.
Applicable to 3.5.3 mainline.
In emu8000.c, size_dram determines the amount of memory on the sound card by
doing write/readback tests starting at 512 KiB and incrementing by 512 KiB.
On success, detected_size is updated to the successful address and testing
continues. On failure, the loop is immediately exited. The resulting
detected_size is 512 KiB too small except in two special cases:
1. If there is no memory, the initial 0 value of detected_size is used, which
is correct.
2. If the address space wraps around, detected_size is updated before the
bailout, so the result is correct.
The patch corrects all cases and was tested with an AWE64 Gold. Before:
EMU8000 [0x620]: 3584 Kb on-board memory detected
asfxload 4GMGSMT.SF2 (4174814 B) fails.
After:
EMU8000 [0x620]: 4096 Kb on-board memory detected
asfxload 4GMGSMT.SF2 succeeds.
I do not have a card with 512 KiB to test with, but by forcibly enabling the
added conditional I verified on the AWE64 Gold that it detects 512 KiB
(successfully reading from the first memory location) and does not hang the
card.
C.f. Bug 46451 https://bugzilla.kernel.org/show_bug.cgi?id=46451
Signed-off-by: David Flater <dave@flaterco.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/isa/cmi8328.c: In function 'snd_cmi8328_remove':
sound/isa/cmi8328.c:416:24: error: 'cmi' undeclared (first use in this function)
sound/isa/cmi8328.c:416:24: note: each undeclared identifier is reported only once for each function it appears in
make[3]: *** [sound/isa/cmi8328.o] Error 1
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce snd-cmi8328 driver for C-Media CMI8328-based sound cards, such as
AudioExcel AV500.
It supports PCM playback and capture (full-duplex) through wss_lib, gameport,
OPL3 and MPU401. The AV500 card has onboard Dream wavetable synth connected
to the MPU401 port and Aux 1 input internally which works too.
The CDROM interface is not supported (as the drivers for these CDROMs were
removed from the kernel some time ago).
A separate driver is needed because CMI8328 is completely different chip to
CMI8329/CMI8330. It's configured by magic registers (there's no PnP). Sound is
provided by a real WSS codec (CS4231A) and the SB part is just a SB Pro
emulation (for DOS games, useless for Linux).
When SB is enabled, the CMI8328 chip disables access to the WSS codec,
emulates SoundBlaster on one side and outputs sound data to the codec - so SB
and WSS can't work together with this card. The WSS codec can do full duplex
by itself so there's no need for crazy things like snd-cmi8330 does
(combining SB and WSS parts into one driver).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_card_als100_probe() does not set pcm field in struct snd_sb.
As a result, PCM is not suspended and applications don't know that they need
to resume the playback.
Tested with Labway A381-F20 card (ALS120).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Implement suspend/resume support for AD1816 chips.
Tested with Terratec SoundSystem Base-1.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
struct snd_card_ad1816a is only set but the values are never used then.
Removing it allows struct snd_card's private_data to be used for
struct snd_ad1816a, simplifying the code.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move snd_legacy_find_free_ioport() function back to initval.h as it is used
by two drivers.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the previous commit, snd_opti9xx_configure() is called from the
resume handler but it's still marked as __devinit. Fix it.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Implement suspend/resume support for Opti 92x and 93x chips.
Tested with Opti 929A+AD1848 and Opti 931.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Yamaha OPL3-SAx chips don't resume properly when playback is running -
garbage is played after resume. Restoring the CS4231_PLAYBK_FORMAT register
last fixes the problem.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
By setting SNDRV_PCM_INFO_RESUME, wss_lib claims that it can restore the card
state fully on resume. But in fact, it can't as DMA is not restored so any
playback/capture running during suspend will fail to continue after resume.
Remove SNDRV_PCM_INFO_RESUME flag from pcm info field to fix the problem.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MED3931 card did not work (failed with "OPTI chip not found") because
snd-opti9xx gets mc_indir_index from pnp by adding 2 to the pnp-reported port.
It probably works for some cards but not for this one. Datasheet says that
the port is always at 0xe?e so just force the lowest nibble to be 0xe.
Also this card powers up with (ugly) 3D sound enabled. As there's no mixer
control for this, just disable it.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
At the point of this error-handling code, both regions and the dma have
been allocated, so free it as done in previous and subsequent
error-handling code.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge with latest Linus' tree, as I have incoming patches
that fix code that is newer than current HEAD of for-next.
Conflicts:
drivers/net/ethernet/realtek/r8169.c
Fix module parameter data type to eliminate build warnings.
sound/isa/opti9xx/opti92x-ad1848.c:87:1: warning: return from incompatible pointer type
sound/isa/opti9xx/opti92x-ad1848.c:87:1: warning: return from incompatible pointer type
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch updates Jonathan Woithe's contact details across the kernel tree.
Signed-off-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The header 'linux/moduleparam.h' is included twice in
'sound/isa/sb/emu8000_patch.c'. Once is enough.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These aren't modules, but they do make use of these macros, so
they will need export.h to get that definition. Previously,
they got it via the implicit module.h inclusion.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Lots of sound drivers were getting module.h via the implicit presence
of it in <linux/device.h> but we are going to clean that up. So
fix up those users now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files were getting access to these two via the implicit
presence of moduleparam.h everywhere. But that is being fixed, so
get these guys what they need in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The implicit presence of module.h lured several users into
incorrectly thinking that they only needed/used modparam.h
but once we clean up the module.h presence, these will show
up as build failures, so fix 'em now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The semantics of snd_mpu401_uart_new()'s interrupt parameters are
somewhat counterintuitive: To prevent the function from allocating its
own interrupt, either the irq number must be invalid, or the irq_flags
parameter must be zero. At the same time, the irq parameter being
invalid specifies that the mpu401 code has to work without an interrupt
allocated by the caller. This implies that, if there is an interrupt
and it is allocated by the caller, the irq parameter must be set to
a valid-looking number which then isn't actually used.
With the removal of IRQF_DISABLED, zero becomes a valid irq_flags value,
which forces us to handle the parameters differently.
This patch introduces a new flag MPU401_INFO_IRQ_HOOK for when the
device interrupt is handled by the caller, and makes the allocation of
the interrupt to depend only on the irq parameter. As suggested by
Takashi, the irq_flags parameter was dropped because, when used, it had
the constant value IRQF_DISABLED.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver doesn't probe the device properly because of left-over cfg[]
that isn't used at all for msnd-classic device. This is only for msnd-
pinnacle.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Its hardware is handled more fully by the new azt1605/azt2316 drivers.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a new driver for Aztech Sound Galaxy ISA soundcards based on the
AZT1605 and AZT2316 chipsets. It's constructed as two seperate drivers
for either chipset generated from the same source file, with (very)
minimal ifdeffery.
The drivers check the SB DSP version to decide if they are being loaded
for the right chip. AZT1605 returns 2.1 by default and AZT2316 3.1.
This isn't full-proof as the DSP version can actually be set through
software but it's close enough -- as far as I've been able to see, the
DSP version can not be stored in the EEPROM and the cards will therefore
startup with the defaults.
This distinction could (with the same success rate) also be used to
decide which chip we're looking at at runtime meaning a single, merged
driver is also an option but I feel it's actually nicer this way. A
merged driver would have to postpone translating the passed in resource
values to the card configuration until it knew which one it was looking
at and would need to postpone erring out on mpu_irq=10 for azt1605 and
mpu_irq=3 for azt2316.
The drivers have been tested on various cards. For snd-azt1605:
FCC-ID I38-MMSN811: Aztech Sound Galaxy Nova 16 Extra
FCC-ID I38-MMSN822: Aztech Sound Galaxy Pro 16 II
and for snd-azt2316:
FCC-ID I38-MMSN824: Aztech Sound Galaxy Pro 16 AB
FCC-ID I38-MMSN826: Trust Sound Expert DeLuxe Wave 32 (05201)
FCC-ID I38-MMSN830: Trust Sound Expert DeLuxe 16+ (05202)
FCC-ID I38-MMSN837: Packard Bell ISA Soundcard 030069
FCC-ID I38-MMSN846: Trust Sound Expert DeLuxe 16-3D (06300)
FCC-ID I38-MMSN847: Trust Sound Expert DeLuxe Wave 32-3D (06301)
FCC-ID I38-MMSN852: Aztech Sound Galaxy Waverider Pro 32-3D
826 and 846 were also marketed directly by Aztech and then known as:
FCC-ID I38-MMSN826: Aztech Sound Galaxy Waverider 32+
FCC-ID I38-MMSN846: Aztech Sound Galaxy Nova 16 Extra II-3D
Together, these cover the AZT1605 and AT2316A, AZT2316R and AZT2316-S
chipsets. All cards work fully -- full-duplex PCM, MIDI and FM. Full
duplex is a little flaky on some.
I38-MSN811 tends to not work in full-duplex but sometimes does with the
highest success rate being achieved when you first start the capture and
then a playback instead of the other way around (it's a CS4231-KL
codec).
The cards with an AD1845XP codec (my I38-MMSN826 and one of my
I38-MMSN830s) are also somewhat duplex-challenged. Sometimes full-duplex
works, sometimes not and this varies from try to try. This seems likely
to be a timing problem somewhere inside wss-lib.
I38-MMSN826 has an additional "ICS2115 WaveFront" wavetable synth
onboard that isn't supported yet. The wavetable synths on I38-MMSN847
and I38-MMSN852 are wired directly to the standard MPU-401 UART and the
AUX1 input on the codec and work without problem.
CD-ROM audio on the cards is routed to the codec "Line" input, Line-In
to its Aux input, and FM/Wavetable to its AUX1 input. I did not rename
the controls due to the capture source enumeration: I see that
capture-source overrides are hardcoded in wss-lib and this is just too
ugly to live.
Versus the old snd-sgalaxy driver these drivers add support for the
models without a configuration EEPROM (which are common), full-duplex,
MPU-401 UART and OPL3. In the future they might grow support for that
ICS2115 WaveFront synth on 826 and an hwdep interface to write to the
EEPROM on the models that have one.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
get_user() may fail, if so return -EFAULT.
[Fixed one missing place by tiwai]
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Smatch complains that if (dev == SNDRV_CARDS) we're one past the end of
the array. That's unlikely to happen in real life, I suppose.
Also smatch complains about "strcpy(card->shortname, pcm->name);"
The "pcm->name" buffer is 80 characters and "card->shortname" is 32
characters. If you follow the call paths it turns out we never actually
use more than 16 characters so it's not a problem. But anyway, let's
make it easy for people auditing this in the future.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ESS ES968 chip is nothing more then a PnP companion
for a non-PnP audio chip. It was paired with non-PnP ESS' chips:
ES688 and ES1688. The ESS' audio chips are handled by the es1688
driver in native mode. The PnP cards are handled by the ES968
driver in SB compatible mode.
Move the ES968 chip handling to the es1688 driver so the driver
can handle both PnP and non-PnP cards. The es968 is removed.
Also, a new PnP id is added for the card I acquired (the change
was tested on this card).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allocate the snd_es1688 during the snd_card allocation.
This allows to remove the card pointer from the snd_es1688 structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is only one dma for the ESS ES968 based board.
Its index is 0 and not 1.
This make the es968 card working.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The llseek implementation is identical for existing driver implementations,
so let's merge to the common layer. The same code for the text proc file
can be used even for the binary proc file.
The driver can provide its own llseek method if needed. Then the common
code will be skipped.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check the validity of the file position in the common info layer before
calling read or write callbacks in assumption that entry->size is set up
properly to indicate the max file size.
Removed the redundant checks from the callbacks as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Fix 'else' placement in ifdef block so that build succeeds:
sound/isa/opti9xx/opti92x-ad1848.c:221: error: 'else' without a previous 'if'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While trying to compile jazz16 isa sound driver on alpha (2.6.33+git), I
found a compile failure in jazz16.c (udelay is unknown). Fix it by
including delay.h.
Signed-foo-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Master Control port (MC) is available as the last
PnP resource (OPT005). Use this value instead fo guessing.
Also, add some comments to the code.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The patch "sbawe: fix memory detection" fixed detection
for memoryless SB32 cards but broke detection of memory
above 512KB. This patch fixes the regression.
The patch has been tested on the SB32 card (CT3670) with
0MB, 2MB and 8MB memory installed.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Narrow the dma and irq selection after the DOS driver.
Add ALSA configuration description as well.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is one of Sound Blaster Pro compatible chipsets which is supported
by Linux OSS driver and was missing native supoort for ALSA.
The Jazz16 audio codec is Crystal CS4216 which is capable
of playback and recording up to 48 kHz stereo.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Memory amount is increased before a successful write-read
sequence is done. Thus, 512 kB of onboard memory is detected
on memoryless cards like SB32.
Move the increasing of memory counter after successful read
is done.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert table of pointers to mixer controls into tables
of the mixer controls. It saves about 20% of the snd-sb-common
module size reported by lsmod.
The als4000 uses part of sb16's control table.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sizeof(share_id) is just the size of the pointer. On the other hand,
block->share_id is an array, so its size seems more appropriate.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
expression f;
type T;
@@
*f(...,(T)x,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Overwrite pin config on intel DG45ID board.
intelhdmi - dont power off HDA link
ALSA: hrtimer - Fix lock-up
ALSA: intelhdmi - add channel mapping for typical configurations
ALSA: intelhdmi - channel mapping applies to Pin
ALSA: intelhdmi - accept DisplayPort pin
ALSA: hda - show HBR(High Bit Rate) pin cap in procfs
ALSA: hda - Fix LED GPIO setup for HP laptops with IDT codecs
ASoC: Fix build of OMAP sound drivers
ALSA: opti93x: fix irq releasing if the irq cannot be allocated
Add dB scale for mixer controls. Fix dB scale for
Master Volume control.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move OPTi93x controls definitions to the opti93x driver
from the common wss-lib library module. These controls
are used only by the opti93x driver.
Also, fix capture source names. They are the same as
opl3sa2 names.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The als100 driver is so similar to the dt019x/als007 driver
that one driver's source can be used for both drivers with
only few changes. Merge the dt019x driver into the als100.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the chip->irq to check if the irq should be released so the irq is not released
if it has not been allocated.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PnP data on the OPTI931 and OPTI933 contains io port
range for the MC indirect registers. Use the PnP range
instead of hardwired value 0xE0E.
Also, request region of MC indirect registers so it is
marked as used to other drivers (this was missing previously).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove snd_opti9xx fields which are indirect arguments to
the snd_opti9xx_configure(). Pass these values as function
arguments.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM12 and PCM20 can be set into the ISA PnP mode. The PCM12 PnP
was sold as the PnP device.
Add code to handle detection of these cards using ISA PnP framework.
Tested on the PCM20 in PnP mode. The PCM12 PnP has the same MS Windows
INF file except for a card name displayed for user.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Separate common probing code in order to use it
for PnP probing.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If a hardware is not detected there is a kernel crash
due to not initialized snd_miro->aci pointer. This pointer
is initialized after detection of the opti (miro) chip.
This bug was introduced by patches to expose
ACI mikser outside the snd-miro driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ACI mixer is used to control the radio FM module
installed on the Miro PCM20 sound card. Expose ACI mixer
outside the sound card driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the miro.h header to the include/sound directory. It can
be used in the Miro PCM20 radio driver (v4l).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the snd_card pointer from the snd_miro structure and
do some small code improvements.
Also, move Opti chipset detection before detection of the
ACI mixer, so the mci_base value is set in one place only.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use db scale for all volume controls according to Crystal's datasheets.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the fm_port and mpu_port variables directly in a probe function.
This completely eliminates a need to copy the fm_port value to
the snd_miro structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update control names to be more closer to their meaning.
Change the "Mono" name to the "Beep" as this line is usually
used to forward the PC beeper signal to sound card's output.
Update names for both cs423x and wss.
Clean up cs4235 controls according to the cs4235 doc. Rename
some of the cs4235 controls to be consistent with the cs4236's
ones.
Also, delete one misnamed cs4231 register define.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
1. Set the third argument of the snd_device_new to not NULL, so there is
no warning about bug during chip detection. The third argument is not
used in this driver. It was changed in my previous patch.
2. Remove the fm_port and mpu_port fields from the snd_es18xx structure.
They can be converted to function arguments.
3. Remove the dmaN_size fields from the snd_es18xx structure. These
values are used only in pointer functions and can be easily calculated.
4. Remove the ctrl_lock spinlock which is used only in one read function
which is called once during chip initialization. There are many
writes to the same register and they are not protected on purpose
(see the comment ina the snd_es18xx_config_write()).
5. Use the first part of the text5Sources string table as the text4Soruces
table (they are the same).
6. Merge the same cases for the ES1887 and ES1888 when setting chip's caps.
7. Move the snd_es18xx_reset() to __devinit section.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The cs4236 was two step detection with call to the snd_wss_free()
between two steps. The snd_wss_free() did not free a sound device
created in the snd_wss_create(). This caused an OOPS during module
removal as the same sound device was released twice. The same OOPS
happened if the cs4236 module loading failed.
Fix this by adapting the snd_cs4236_create() to correctly work with
chips less capable then cs4236. The snd_cs4236_create() behaves the
same as the snd_wss_create() if the chip is less capable than the cs4236.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai