Add new V4L2 stream format definition, V4L2_BUF_TYPE_SDR_CAPTURE,
for SDR receiver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Define tuner types V4L2_TUNER_ADC and V4L2_TUNER_RF for SDR usage.
ADC is used for setting sampling rate (sampling frequency) to SDR
device.
Another tuner type, named as V4L2_TUNER_RF, is possible RF tuner.
Is is used to down-convert RF frequency to range ADC could sample.
Having RF tuner is optional, whilst in practice it is almost always
there.
Also add checks to VIDIOC_G_FREQUENCY, VIDIOC_S_FREQUENCY and
VIDIOC_ENUM_FREQ_BANDS only allow these two tuner types when device
type is SDR (VFL_TYPE_SDR). For VIDIOC_G_FREQUENCY we do not check
tuner type, instead override type with V4L2_TUNER_ADC in every
case (requested by Hans in order to keep functionality in line with
existing tuners and existing API does not specify it).
Prohibit VIDIOC_S_HW_FREQ_SEEK explicitly when device type is SDR,
as device cannot do hardware seek without a hardware demodulator.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add new V4L device type VFL_TYPE_SDR for Software Defined Radio.
It is registered as /dev/swradio0 (/dev/sdr0 was already reserved).
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This device has a led at bit 7 of GPIO reg. 0x80 to indicate
when a DVB capture is happening.
Add support for it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This device is close to Kworld UB435-Q, but it uses a different
tuner. Add support for it.
Tested with both 8VSB and 256QAM modulations.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
tda18272 is programmed just like tda18212, but it also
supports ClearQAM and ATSC.
Add support for them. Tested with a Kworld UB435-Q on both
8VSB and 256QAM modes.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently, there's just one device using this frontend: PCTV 80e,
and it works on serial mode.
Change the default here to serial mode. If we add more devices,
then this option should be set via config structure.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The cfg_mpeg_output has more fields than what it is initialized
when the code is called. Be sure to initialize everything before
use, in order to avoid random behaviors.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Just like the windows driver, disable OOB after setting the driver
version.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
DJH_DEBUG only code path in drxbsp_i2c_write_read() dereferences
w_dev_addr and subsequently w_dev_addr->user_data->i2c which results
in failure during boot. This patch fixes the null pointer derefence
bug as well as the following compile errors:
LD arch/x86/built-in.o
CC drivers/media/dvb-frontends/drx39xyj/drxj.o
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function ‘drxbsp_i2c_write_read’:
drivers/media/dvb-frontends/drx39xyj/drxj.c:1558:25: error: redeclaration of ‘state’ with no linkage
struct drx39xxj_state *state = w_dev_addr->user_data;
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1512:25: note: previous declaration of ‘state’ was here
struct drx39xxj_state *state;
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1558:2: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement]
struct drx39xxj_state *state = w_dev_addr->user_data;
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1560:17: error: redeclaration of ‘msg’ with no linkage
struct i2c_msg msg[2] = {
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1513:17: note: previous declaration of ‘msg’ was here
struct i2c_msg msg[2];
^
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mimic what windows driver does here: it writes 0x07 to
SIO_CC_SOFT_RST__A, instead of just 0x03.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As drxj_close puts the device in powerdown, we need to power it up
properly at drxj_open.
This is the behavior noticed at the Windows driver.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are no other I2C masters here. Also, the Windows driver uses
this mode (and both drxd and drxk Kernel drivers). So, switch
to it.
That helps to compare the logs between the Linux driver and the
Windows one.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of just disabling the LNA every time, allow to control it from
userspace.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On several places, the I2C functions are just wrappers to others.
Get rid of it.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This struct contains the first abstraction layer for the I2C
access routines. Get rid of it.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This file contains an abstract layer for the I2C transfer
functions. Get rid of it, merging it at drxj. This will allow
to remove another abstraction layer there, making the code
easier to read, and removing the functions that just return
-EIO.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reorder functions and data at drx_dap_fasi.c, in order to avoid
having function prototypes.
This is in preparation to merge this code inside drxj, removing
some duplicated bits there, and getting rid of yet another
abstraction layer.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is not used anywere. Get rid of it.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
QAM/256 currently doesn't work, as the code is only called if
channel->mirror is DRX_MIRROR_AUTO, but a prevous if prevents
this condition to happen.
While here, returns -EINVAL to not supported QAM modes and
simplify the code, reducing the number of indents.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Those struct data aren't used anymore. Get rid of them.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Checking if a time is after another one can have issues, as
times are generally u32 wide.
Use the proper macros for that at scu_command().
It should be noticed that other places also use jiffies
calculus on an improper way. This should be fixed too,
but the logic there is more complex. So, let's do it in
separate patches.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Modulation and other parameters might have changed. So, better
to call ctrl_set_standard() even if the device is already
powered.
That helps to put the device into a sane state, if something
got wrong on a previous set_frontend call.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When switching from one video standard to another one,
power_down_vsb is called twice. Well, as the device is already
in power_down mode, the second call always fail. This causes that
any subsequent frontend set to fail as well:
[145074.501243] drx39xyj:power_down_vsb: called
[145089.195396] drx39xyj:power_down_vsb: error -5
[145089.195404] drx39xyj:ctrl_set_standard: error -5
[145089.195417] drx39xyj:drx39xxj_set_frontend: Failed to set standard! result=fffffffb
[145089.195470] drx39xyj:ctrl_sig_quality: error -5
[145089.195473] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145089.195475] drx39xyj:ctrl_sig_quality: error -5
[145089.195477] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145089.195479] drx39xyj:ctrl_sig_quality: error -5
[145089.195480] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145089.195482] drx39xyj:ctrl_sig_quality: error -5
[145089.195484] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
[145089.195498] drx39xyj:ctrl_sig_quality: error -5
[145089.195500] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145089.195502] drx39xyj:ctrl_sig_quality: error -5
[145089.195503] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145089.195505] drx39xyj:ctrl_sig_quality: error -5
[145089.195506] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145089.195508] drx39xyj:ctrl_sig_quality: error -5
[145089.195510] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
[145090.196291] drx39xyj:drx39xxj_read_status: drx39xxj: could not get lock status!
[145090.196508] drx39xyj:ctrl_sig_quality: error -5
[145090.196511] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145090.196514] drx39xyj:ctrl_sig_quality: error -5
[145090.196515] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145090.196518] drx39xyj:ctrl_sig_quality: error -5
[145090.196519] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145090.196522] drx39xyj:ctrl_sig_quality: error -5
[145090.196523] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
[145090.196553] drx39xyj:ctrl_sig_quality: error -5
[145090.196554] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145090.196557] drx39xyj:ctrl_sig_quality: error -5
[145090.196558] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145090.196560] drx39xyj:ctrl_sig_quality: error -5
[145090.196562] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145090.196564] drx39xyj:ctrl_sig_quality: error -5
[145090.196565] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
[145091.119265] drx39xyj:ctrl_sig_quality: error -5
[145091.119271] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145091.119274] drx39xyj:ctrl_sig_quality: error -5
[145091.119276] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145091.119278] drx39xyj:ctrl_sig_quality: error -5
[145091.119280] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145091.119282] drx39xyj:ctrl_sig_quality: error -5
[145091.119283] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of just hardcoding an IF value of 5MHz, use the one
provided by the tuner, with can be different for QAM and
VSB.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Those functions will never be used with Linux DVB binding.
Get rid of them.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This file does an ugly binding between drxj and DVB frontend.
Remove most of the functions there. We still need to get rid of
get_frequency and set_frequency, but such patch is a little more
complex, as it should also remove some previous tuner bindings.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In order to avoid warnings and to remove dead code, remove
the functions that don't make sense to happen, while commenting
the others that might still be useful some day.
That reduced a lot the text size:
Before:
text data bss dec hex filename
58419 2916 4 61339 ef9b drivers/media/dvb-frontends/drx39xyj/drx39xyj.ko
After:
text data bss dec hex filename
78331 2916 4 81251 13d63 drivers/media/dvb-frontends/drx39xyj/drx39xyj.ko
Without any functional changes.
It could be make sense latter to remove those drivers or to
move them into an analog-specific part of the driver.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
With this change, we finally got rid of all abstraction
layers on this driver.
This patch also fixes the LNA GPIO settings, as the original
code were using a wrong control name for it.
This patch exposes the several functions that aren't used.
Some of them are related to analog demod that might be
used some day, but others will likely never be needed, as
they don't fit on Linux media APIs.
Latter patches will clean up this mess.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
While drxj is already too big, moving the code there will
make easier to get rid of the drxj_ctrl function.
It will also help to detect and remove the unused functions,
helping to remove lots of dead code there.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Get rid of drx_open and drx_close, as those are just wrapper
functions to drxj_open/drxj_close.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This function is used only as an abstraction layer to call the
two firmware functions. Remove it.
As a bonus, the drx_ctrl_function is now unused and can be
removed.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove the duplicated firmware upload code that was commented
inside drxj.c.
This code is not used, and will not work anyway, as it doesn't
download the firmware from userspace.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The version is initialized with zero at drx_driver.c. Keep it,
in order to avoid the risk of causing any regression.
While here, remove the drx_driver.h from drxj, as this is not
required there.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This file contains just the firmware load code, that it is also
somewhat duplicated at drxj.c.
Move the code into there. Latter patches will remove the
duplicated code.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In order to prepare to get rid of drx_driver.c, prepend all functions
there with drx_.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is mostly CodingStyle fixes and improvements.
No functional changes.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
ClearQAM is currently not working. Add support for it too.
Unlikely other ATSC tuners, though, this device will not
auto-detect between ATSC and ClearQAM. So, the delivery
system should be properly set.
Also, this frontend seems to also support DVB-C annex A/C. Add
experimental support for them.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Without this fixup, the DRX-J will not be properly initialized,
loosing several PIDs.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of handling endiannes with its own internal way, use the
already existing macros.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are several drx-j code there that are never used, as
they don't even fit into Linux DVB subystem model.
Remove them, in order to simplify the code.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This stick uses the same RC-5 remote controll found on other
PCTV devices. So, just use the existing keymap.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The firmware upload routine is already complex enough. Split the
first loop that verifies the firmware size into a separate routine,
making the code more readable.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of hardcoding the firmware files together with the driver,
use request_firmware() way, loading it from userspace.
The firmware files are placed at:
http://linuxtv.org/downloads/firmware/#8
And they'll be latter submitted to linux-firmware git tree.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The state struct is allocated without cleaning the memory.
This causes random bugs.
Clean it, and move the memcpy functions just below each kalloc,
to be clearer that all those data are properly filled.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are memory leaks on both DVB release and
dvb attach error path. Fix them.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This var is not used. Remove it from the code, as we'll now be
converting the driver to load the firmware from an external
file.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This file is empty (actually, all commented there). So, remove it.
We should latter remove those macros too, or convert them into
a struct to allow dynamically enable the options during device
probing time.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Get rid of another typedef defined on this driver.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of using printk's, use the pr_foo() macros.
That fixes some checkpatch warnings and provide a better error,
warning and debug support.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of defining its own set of error codes, use the linux
native ones.
Please note that this patch made a "stupid" error code mapping, just
replacing the codes with the closest one. In special, -EIO is being
used on several places. I'm pretty sure this could be better assigned,
but a change like that would require lots o time and efforts, without
much benefit.
So lets do adjstments at the error codes latter, when we have more
time.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix almost all checkpatch.pl warnings/errors on drxj.c, except for:
- 80 cols whitespacing;
- too many leading tabs;
- a false positive at DRXJ_16TO8() macro.
- static char array declaration should probably be static const char
as adding "const" would cause warnings.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove three typedefs from drxj.c, using the following script:
use File::Find;
use strict;
my $dir = shift or die "need a dir";
my $type = shift or die "need type";
my $var = shift or die "need var";
sub handle_file {
my $file = shift;
my $out;
open IN, $file or die "can't open $file";
$out .= $_ while (<IN>);
close IN;
$out =~ s/\btypedef\s+($type)\s+\{([\d\D]+?)\s*\}\s+\b($var)[^\;]+\;/$type $var \{\2\};/;
# This replaces the typedef declaration for a simple struct declaration - style 1
# This replaces the typedef declaration for a simple struct declaration - style 2
# Replace struct occurrences
$out =~ s,\b($var)_t\s+,$type \1 ,g;
$out =~ s,\bp_*($var)_t\s+,$type \1 *,g;
$out =~ s,\b($var)_t\b,$type \1,g;
$out =~ s,\bp_*($var)_t\b,$type \1 *,g;
open OUT, ">$file" or die "can't open $file";
print OUT $out;
close OUT;
}
sub parse_dir {
my $file = $File::Find::name;
return if (!($file =~ /.[ch]$/));
handle_file $file;
}
find({wanted => \&parse_dir, no_chdir => 1}, $dir);
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Don't need to test boolean x == true or x == false.
That makes the code more compact.
patch generated with make coccicheck and manually reviewed.
While here, remove uneeded ';'.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
CodingStyle fix: don't use parenthesis on return, as it is not
a function.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function ‘drxj_dap_scu_atomic_read_reg16’:
drivers/media/dvb-frontends/drx39xyj/drxj.c:4170:9: warning: ‘*((void *)&buf+1)’ may be used uninitialized in this function [-Wmaybe-uninitialized]
word = (u16) (buf[0] + (buf[1] << 8));
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:4170:9: warning: ‘buf’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function ‘drxj_dap_atomic_read_reg32.isra.59’:
drivers/media/dvb-frontends/drx39xyj/drxj.c:2186:7: warning: ‘*((void *)&buf+3)’ may be used uninitialized in this function [-Wmaybe-uninitialized]
word = (u32) buf[3];
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:2188:10: warning: ‘*((void *)&buf+2)’ may be used uninitialized in this function [-Wmaybe-uninitialized]
word |= (u32) buf[2];
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:2190:10: warning: ‘*((void *)&buf+1)’ may be used uninitialized in this function [-Wmaybe-uninitialized]
word |= (u32) buf[1];
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:2192:10: warning: ‘buf’ may be used uninitialized in this function [-Wmaybe-uninitialized]
word |= (u32) buf[0];
^
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This were fixed with the help of this small perl script:
#!/usr/bin/perl
my $dir = shift or die "need a dir";
my $type = shift or die "need type";
my $var = shift or die "need var";
sub handle_file {
my $file = shift;
my $out;
open IN, $file or die "can't open $file";
$out .= $_ while (<IN>);
close IN;
$out =~ s/\btypedef\s+($type)\s+\{([\d\D]+?)\s*\}\s+\b($var)[^\;]+\;/$type $var \{\2\};/;
$out =~ s,\b($var)_t\s+,$type \1 ,g;
$out =~ s,\bp_*($var)_t\s+,$type \1 *,g;
$out =~ s,\b($var)_t\b,$type \1,g;
$out =~ s,\bp_*($var)_t\b,$type \1 *,g;
open OUT, ">$file" or die "can't open $file";
print OUT $out;
close OUT;
}
sub parse_dir {
my $file = $File::Find::name;
return if (!($file =~ /.[ch]$/));
handle_file $file;
}
find({wanted => \&parse_dir, no_chdir => 1}, $dir);
Some manual work were needed.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Most of the changes were done with scripts like:
for i in drivers/media/dvb-frontends/drx39xyj/*.[ch]; do perl -ne '$var = "drx_sig_quality"; s,\b($var)_t\s+,struct \1 ,g; s,\bp_*($var)_t\s+,struct \1 *,g; s,\b($var)_t\b,struct \1,g; s,\bp_*($var)_t\b,struct \1 *,g; print $_' <$i >a && mv a $i; done
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This file is not used anywhere. Drop it.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
None of those vars are used on those functions. Just remove them.
After this patch, there's just one of such warnings:
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function 'ctrl_get_qam_sig_quality':
drivers/media/dvb-frontends/drx39xyj/drxj.c:7872:6: warning: variable 'ber_cnt' set but not used [-Wunused-but-set-variable]
u32 ber_cnt = 0; /* BER count */
We'll keep it, as BER count will be useful when converting the
frontend to report statistics via DVBv5 API
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This function is not static. Also, it is not used anywhere.
So, drop it.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This time, use checkpatch --strict --fix.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There's no reason at all to use CamelCase here. Convert all of
them to normal case.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of manually fixing the issues, use the --fix experimental
checkpatch. That solves a bunch of checkpatch issues.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Patch generated with this script:
for i in drivers/media/dvb-frontends/drx39xyj/*.[ch]; do perl -ne 's,(enum|struct|void|int|u32|u64|u16|u8|s8|s16|s32|s64)\s+(\S+)\s+\*[ ]+,\1 \2 *,g; print $_' <$i >a && mv a $i; done
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are lots of typedefs there. Let's get rid of them.
Most of the work here is due to this small script:
if [ "$3" == "" ]; then
echo "usage: $0 type DRXName drx_name"
fi
t=$1; f=$2; g=$3
for i in *.[ch]; do
sed s,"p${f}_t","$t $g *",g <$i >a && mv a $i && \
sed s,"${f}_t","$t $g",g <$i >a && mv a $i
done
Just kept there the function typedefs, as those are still useful.
Yet, all those tuner_ops can likely be just removed on a latter
cleanup patch.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move them into drx_driver.h
That makes easier to cleanup further what's there at the
headers.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Most of the work were done by those small scripts:
for i in *; do sed s,pDRXFrequency_t,"s32 *",g <$i >a && mv a $i; done
for i in *; do sed s,DRXFrequency_t,"s32",g <$i >a && mv a $i; done
for i in *; do sed s,pDRXSymbolrate_t,"u32 *",g <$i >a && mv a $i; done
for i in *; do sed s,DRXSymbolrate_t,"u32",g <$i >a && mv a $i; done
for i in *; do sed s,FALSE,false,g <$i >a && mv a $i; done
for i in *; do sed s,TRUE,true,g <$i >a && mv a $i; done
for i in *; do sed s,Bool_t,bool,g <$i >a && mv a $i; done
for i in *; do sed s,pbool,"bool *",g <$i >a && mv a $i; done
The only remaining things there are the return values.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Patch created using this small script:
for j in 8 16 32; do for i in *; do sed s,pu${j}_t,"u$j *",g <$i >a && mv a $i; done; done
for j in 8 16 32; do for i in *; do sed s,ps${j}_t,"s$j *",g <$i >a && mv a $i; done; done
for j in 8 16 32; do for i in *; do sed s,s${j}_t,"s$j",g <$i >a && mv a $i; done; done
for j in 8 16 32; do for i in *; do sed s,u${j}_t,"u$j",g <$i >a && mv a $i; done; done
and fixing the bsp_types.h header.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
After removing the typedef, it is now clear that HICommand() were
abusing of a var that was expecting to be constant:
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function ‘HICommand’:
drivers/media/dvb-frontends/drx39xyj/drxj.c:2272:3: warning: passing argument 1 of ‘drxDapDRXJFunct_g.writeReg16Func’ discards ‘const’ qualifier from pointer target type [enabled by default]
drivers/media/dvb-frontends/drx39xyj/drxj.c:2272:3: note: expected ‘struct i2c_device_addr *’ but argument is of type ‘const struct i2c_device_addr *’
drivers/media/dvb-frontends/drx39xyj/drxj.c:2273:3: warning: passing argument 1 of ‘drxDapDRXJFunct_g.writeReg16Func’ discards ‘const’ qualifier from pointer target type [enabled by default]
drivers/media/dvb-frontends/drx39xyj/drxj.c:2273:3: note: expected ‘struct i2c_device_addr *’ but argument is of type ‘const struct i2c_device_addr *’
drivers/media/dvb-frontends/drx39xyj/drxj.c:2274:3: warning: passing argument 1 of ‘drxDapDRXJFunct_g.writeReg16Func’ discards ‘const’ qualifier from pointer target type [enabled by default]
drivers/media/dvb-frontends/drx39xyj/drxj.c:2274:3: note: expected ‘struct i2c_device_addr *’ but argument is of type ‘const struct i2c_device_addr *’
drivers/media/dvb-frontends/drx39xyj/drxj.c:2275:3: warning: passing argument 1 of ‘drxDapDRXJFunct_g.writeReg16Func’ discards ‘const’ qualifier from pointer target type [enabled by default]
drivers/media/dvb-frontends/drx39xyj/drxj.c:2275:3: note: expected ‘struct i2c_device_addr *’ but argument is of type ‘const struct i2c_device_addr *’
drivers/media/dvb-frontends/drx39xyj/drxj.c:2278:3: warning: passing argument 1 of ‘drxDapDRXJFunct_g.writeReg16Func’ discards ‘const’ qualifier from pointer target type [enabled by default]
drivers/media/dvb-frontends/drx39xyj/drxj.c:2278:3: note: expected ‘struct i2c_device_addr *’ but argument is of type ‘const struct i2c_device_addr *’
drivers/media/dvb-frontends/drx39xyj/drxj.c:2279:3: warning: passing argument 1 of ‘drxDapDRXJFunct_g.writeReg16Func’ discards ‘const’ qualifier from pointer target type [enabled by default]
drivers/media/dvb-frontends/drx39xyj/drxj.c:2279:3: note: expected ‘struct i2c_device_addr *’ but argument is of type ‘const struct i2c_device_addr *’
drivers/media/dvb-frontends/drx39xyj/drxj.c:2291:2: warning: passing argument 1 of ‘drxDapDRXJFunct_g.writeReg16Func’ discards ‘const’ qualifier from pointer target type [enabled by default]
drivers/media/dvb-frontends/drx39xyj/drxj.c:2291:2: note: expected ‘struct i2c_device_addr *’ but argument is of type ‘const struct i2c_device_addr *’
drivers/media/dvb-frontends/drx39xyj/drxj.c:2311:4: warning: passing argument 1 of ‘drxDapDRXJFunct_g.readReg16Func’ discards ‘const’ qualifier from pointer target type [enabled by default]
drivers/media/dvb-frontends/drx39xyj/drxj.c:2311:4: note: expected ‘struct i2c_device_addr *’ but argument is of type ‘const struct i2c_device_addr *’
drivers/media/dvb-frontends/drx39xyj/drxj.c:2315:3: warning: passing argument 1 of ‘drxDapDRXJFunct_g.readReg16Func’ discards ‘const’ qualifier from pointer target type [enabled by default]
drivers/media/dvb-frontends/drx39xyj/drxj.c:2315:3: note: expected ‘struct i2c_device_addr *’ but argument is of type ‘const struct i2c_device_addr *’
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Most of the hard work here were done by this small script:
for i in *; do sed s,pI2CDeviceAddr_t,"struct i2c_device_addr *",g <$i >a && mv a $i; done
for i in *; do sed s,I2CDeviceAddr_t,"struct i2c_device_addr",g <$i >a && mv a $i; done
Only bsp_i2c.h were added by hand.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There were some DVB internal API changes, since this driver were
written. Change it to work with the new API.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Do the automatic CodingStyle fixes found at Lindent.
No functional changes.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Relicense the drx-j driver under a standard 3-clause BSD license, which makes
it GPL compatible.
This was done explicitly with permission from Trident Microsystems.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for the Trident DRX-J driver, including a card profile for the
PCTV 80e which uses the chip.
Thanks to Trident for allowing the release of this code under a BSD license,
and of course Hauppauge/PCTV for pushing for its release to the community.
[pdickeybeta@gmail.com: modified to fix compilation errors and also to move
the driver files from the drx39xy subdirectory to the frontends directory]
[m.chehab@samsung.com: fix merge conflicts, commented drx-j compilation and
added EM28XX_R06_I2C_CLK setup also to the board setup]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If an attempt to set LNA fails, restore the cache to LNA_AUTO,
in order to make it to reflect the current LNA status.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Several URBs will be simply not filled. Don't call the DVB
core software filter for those empty URBs.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement em28xx_usb_driver suspend, resume, and reset_resume hooks.
These hooks will invoke em28xx core em28xx_suspend_extension() and
em28xx_resume_extension() to suspend and resume registered extensions.
Approach:
Add power management support to em28xx usb driver. This driver works in
conjunction with extensions for each of the functions on the USB device
for video/audio/dvb/remote functionality that is present on media USB
devices it supports. During suspend and resume each of these extensions
will have to do their part in suspending the components they control.
Adding suspend and resume hooks to the existing struct em28xx_ops will
enable the extensions the ability to implement suspend and resume hooks
to be called from em28xx driver. The overall approach is as follows:
-- add suspend and resume hooks to em28xx_ops
-- add suspend and resume routines to em28xx-core to invoke suspend
and resume hooks for all registered extensions.
-- change em28xx dvb, audio, input, and video extensions to implement
em28xx_ops: suspend and resume hooks. These hooks do what is necessary
to suspend and resume the devices they control.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement em28xx_ops: suspend/resume hooks. em28xx usb driver will
invoke em28xx_ops: suspend and resume hooks for all its extensions
from its suspend() and resume() interfaces.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement em28xx_ops: suspend/resume hooks. em28xx usb driver will
invoke em28xx_ops: suspend and resume hooks for all its extensions
from its suspend() and resume() interfaces.
[m.chehab@samsung.com: Fix a breakage caused by calling a non-existing
function call: schedule_delayed_work_sync(), and test if IR was defined
at suspend/resume]
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement em28xx_ops: suspend/resume hooks. em28xx usb driver will
invoke em28xx_ops: suspend and resume hooks for all its extensions
from its suspend() and resume() interfaces.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement em28xx_ops: suspend/resume hooks. em28xx usb driver will
invoke em28xx_ops: suspend and resume hooks for all its extensions
from its suspend() and resume() interfaces.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
em28xx usb driver will have to suspend and resume its extensions. Adding
suspend and resume to em28xx_ops gives extensions the ability to install
suspend and resume that can be invoked from em28xx_usb driver suspend()
and resume() interfaces.
Approach:
Add power management support to em28xx usb driver. This driver works in
conjunction with extensions for each of the functions on the USB device
for video/audio/dvb/remote functionality that is present on media USB
devices it supports. During suspend and resume each of these extensions
will have to do their part in suspending the components they control.
Adding suspend and resume hooks to the existing struct em28xx_ops will
enable the extensions the ability to implement suspend and resume hooks
to be called from em28xx driver. The overall approach is as follows:
-- add suspend and resume hooks to em28xx_ops
-- add suspend and resume routines to em28xx-core to invoke suspend
and resume hooks for all registered extensions.
-- change em28xx dvb, audio, input, and video extensions to implement
em28xx_ops: suspend and resume hooks. These hooks do what is necessary
to suspend and resume the devices they control.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Restructure the way we bring the various GPIOs out of reset. In particular:
1. we only need to setup the GPIOs as outputs once
2. there's no point in writing 0x40 to register 0x00 since that's the EEPROM
write protect and already it's configured as an input
3. Separate out the act of enabling the power supply and bringing the tuner
and demod out of reset. If you don't then the chip may not be properly
enabled (as the power supply is still ramping up when the chip comes
out of reset). This can result in probing failures.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
An attempt was made to read dvbs2_snr_tab[80],
though dvbs2_snr_tab has only 80 elements.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We are checking sizeof() the wrong variable!
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
No need to check lock twice here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add m88rs2000_get_tune_settings, min delay of 2000 ms on symbol
rate more than 3000000 and delay of 3000ms less than this.
Adding min delay prevents crashing the frontend on continuous
transponder scans. Other dvb_frontend_tune_settings remain as default.
This makes very little time difference to good channel scans, but slows down
the set frontend where lock can never be achieved i.e. DVB-S2.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds Controls to set Horizontal and Vertical search range
for Motion Estimation block for Samsung MFC video Encoders.
Signed-off-by: Swami Nathan <swaminath.p@samsung.com>
Signed-off-by: Amit Grover <amit.grover@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adding V4L2 controls for horizontal and vertical search range in pixels
for motion estimation module in video encoder.
Signed-off-by: Swami Nathan <swaminath.p@samsung.com>
Signed-off-by: Amit Grover <amit.grover@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
"err" is zero here so we don't need to check again.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Messages relative to kinect_read() are printing "res" which contains the
return value of a previous kinect_write().
Print the correct value in the messages.
Cc: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The error checking code relative to the invocations of kinect_read()
does not return the actual return code of the function just called, it
returns "res" which still contains the value of the last invocation of
a previous kinect_write().
Return the proper value, and while at it also report with -EREMOTEIO the
case of a partial transfer.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Upgrade to videobuf2 libraries.
No errors reported with "v4l2-compliance -s".
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
sleep_on and its variants are broken and going away soon. This changes
the omap vout driver to use wait_event_interruptible_timeout instead,
which fixes potential race where the dma is complete before we
schedule.
[hans.verkuil@cisco.com: replaced interruptible_sleep_on_timeout by
wait_event_interruptible_timeout in the commit msg, obvious typo]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: linux-media@vger.kernel.org
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
interruptible_sleep_on is racy and going away. This replaces
one use in the radio-cadet driver with a wait_event_interruptible
call. Special care was taken that accesses to the rdsin and rdsout
indices are always done with dev->lock held.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Closer inspection on exact transmitted format showed that
we needed to add 1 on vertical sync.
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
HS_IN/VS_IN was always set to positive.
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently only RGB444 input data is supported so set to zero.
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Removal of unnecessary parameters from s2255_fh.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Start acquisition return code was not being checked. Return error
if start acquisition fails.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver was allocating a kernel buffer each time it was sending a command.
It is better to allocate this buffer once at startup.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Removing duplicate fmt from buffer structure.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Buffer setup should check if minimum number of buffers is used.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Renaming s2255_channel and all instances of channel to vc (video channel).
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Removal of unused and unnecessary s2255dma_queue structure.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch enables the ioctl to create additional buffers on the
videobuf2 capture queue.
[laurent.pinchart@ideasonboard.com: Acquire privileges instead of just
checking them in VIDIOC_CREATE_BUFS implementation]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The queue_setup handler takes an optional format argument that can be
used to allocate buffers for a format different than the current format.
The uvcvideo driver doesn't support changing the format when buffers
have been allocated, but there's no reason not to support allocating
buffers larger than the minimum size.
When the format argument isn't NULL verify that the requested image size
is large enough for the current format and use it for the buffer size.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
videobuf2 already ensures that the number of buffers will not exceed
VIDEO_MAX_FRAME, which is equal to our arbitraty limit of
UVC_MAX_VIDEO_BUFFERS. Remove the duplicate check.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Isochronous endpoints on devices with speed == USB_SPEED_WIRELESS can
have a max packet size ranging from 1-3584 bytes. Add a case to
uvc_endpoint_max_bpi to handle USB_SPEED_WIRELESS. Otherwise endpoints
for those devices will fall to the default case which masks off any
values > 2047. This causes uvc_init_video to underestimate the
bandwidth available and fail to find a suitable alt setting for high
bandwidth video streams.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
x < constant implies x + unsigned < constant
That check just obfuscates the code
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the input clock frequency is out of bounds for the PLL, bypass the
PLL and just divide the input clock to achieve the requested output
frequency.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sensor needs a master clock, handle it explictly in the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sensor needs two power supplies, VAA and VDD. Require a regulator
for each of them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
A failure to locate the external subdev for a non memory-to-memory
pipeline is a fatal error, don't ignore it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Tested-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Memory-to-memory pipelines have no external subdev, we shouldn't try to
locate one and validate its configuration. The driver currently works by
chance due to another bug that results in failure to locate the external
subdev being ignored.
This gets rid of the "omap3isp omap3isp: can't find source, failing now"
error message in the kernel log when operating on a memory-to-memory
pipeline.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Tested-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 3fdfedaaa "[media] omap3isp: preview: Lower the crop margins"
accidentally changed the previewer's cropping, causing the previewer
to miss four pixels on each line, thus corrupting the final image.
Restored the removed setting.
Cc: stable@vger.kernel.org
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Drop the vid_limit module option: there is really no need to limit this.
No other driver does that. If you try to allocate more buffers then vb2
will automatically reduce the number of buffers anyway.
Also add sanity checks if the size in the fmt argument is going to be
used and drop the code that checks against *nbuffers == 0: this can
never happen (the vb2 framework ensures that) and the code was wrong
anyway since *nbuffers should have been set to the minimum number of
required buffers which is 1 for this driver.
Since vivi is often used as a template driver it is good to have this
driver be as compliant as possible. This broken code was for example
copied to the s2255 driver (which is being fixed as well).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sequence counting was not reset to 0 between each streaming run,
and it was increased only every other frame. This is incorrect behavior:
the confusion is with FIELD_ALTERNATE systems where each field is transmitted
separately and only when both fields have been received is the frame
sequence number increased.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for 32-bit ioctls with v4l-subdev device nodes.
Rather than keep adding new ioctls to the list in v4l2-compat-ioctl32.c, just check
if the ioctl is a non-private V4L2 ioctl and if so, call the conversion code.
We keep forgetting to add new ioctls, so this is a more robust solution.
In addition extend the subdev API with support for a compat32 function to
convert custom v4l-subdev ioctls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This driver has been replaced by af9033 and tuner_it913x
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Following moving ids to af9035.
This driver is no longer in use.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some device vendors has forgotten set correct slave demod I2C address
to eeprom. Use default I2C address when eeprom has no address at all.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As follow on to patch
af9035: Move it913x single devices to af9035
and patch 1.
SNR is reported as db/10 values.
All dual ids are added to af9035 and it913x driver disabled.
it913x/it913x-fe removal patches to follow.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On some devices the vendor has not set EEPROM_2ND_DEMOD_ADDR.
Checks tmp is not zero after call to get EEPROM_2ND_DEMOD_ADDR and sets the
default slave address of 0x3a on 0x9135 devices.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The generic v1 and v2 devices have been all tested.
IDs tested
USB_PID_ITETECH_IT9135 v1 & v2
USB_PID_ITETECH_IT9135_9005 v1
USB_PID_ITETECH_IT9135_9006 v2
Current Issues
There is no signal on
USB_PID_ITETECH_IT9135 v2
No SNR reported all devices.
All single devices tune and scan fine.
All remotes tested okay.
Dual device failed to register second adapter
USB_PID_KWORLD_UB499_2T_T09
It is not clear what the problem is at the moment.
So only single IDs are transferred in this patch.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Tuner PLL lock flag was mapped to FE_HAS_SIGNAL, which is wrong. PLL
lock has nothing to do with received signal. In real life that flag
is always set.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
"ret" is an error code here, we already tested that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
I've got the following DAB USB stick that also works fine with the
DVB_USB_RTL28XXU driver after I added its USB ID:
Bus 001 Device 009: ID 0ccd:00b4 TerraTec Electronic GmbH
[crope@iki.fi: apply patch partly manually]
Signed-off-by: Till Dörges <till@doerges.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add missing m88ts2022 module reference counts as removing that module
is not allowed when it is used by em28xx-dvb module. That same module
was not unregistered correctly, fix it too.
Error cases validated by returning errors from m88ds3103, m88ts2022
and a8293 probe().
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
da9846ae15 ("kernfs: make kernfs_deactivate() honor KERNFS_LOCKDEP
flag") in driver-core-linus conflicts with kernfs_drain() updates in
driver-core-next. The former just adds the missing KERNFS_LOCKDEP
checks which are already handled by kernfs_lockdep() checks in
driver-core-next. The conflict can be resolved by taking code from
driver-core-next.
Conflicts:
fs/kernfs/dir.c
dma_buf_map_attachment and dma_buf_vmap can return NULL or
ERR_PTR on a error. This encourages a common buggy pattern in
callers:
sgt = dma_buf_map_attachment(attach, DMA_BIDIRECTIONAL);
if (IS_ERR_OR_NULL(sgt))
return PTR_ERR(sgt);
This causes the caller to return 0 on an error. IS_ERR_OR_NULL
is almost always a sign of poorly-defined error handling.
This patch converts dma_buf_map_attachment to always return
ERR_PTR, and fixes the callers that incorrectly handled NULL.
There are a few more callers that were not checking for NULL
at all, which would have dereferenced a NULL pointer later.
There are also a few more callers that correctly handled NULL
and ERR_PTR differently, I left those alone but they could also
be modified to delete the NULL check.
This patch also converts dma_buf_vmap to always return NULL.
All the callers to dma_buf_vmap only check for NULL, and would
have dereferenced an ERR_PTR and panic'd if one was ever
returned. This is not consistent with the rest of the dma buf
APIs, but matches the expectations of all of the callers.
Signed-off-by: Colin Cross <ccross@android.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are several left overs with my old email address.
Remove their occurrences and add myself at CREDITS, to
allow people to be able to reach me on my new addresses.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Change 32bit NEC scancode format (used by Apple and TiVo remotes) to
encode the data with the correct bit order. Previously the raw bits were
used without being bit reversed, now each 16bit half is bit reversed
compared to before.
So for the raw NEC data:
(LSB/First) 0xAAaaCCcc (MSB/Last)
(where traditionally AA=address, aa=~address, CC=command, cc=~command)
We now generate the scancodes:
(MSB) 0x0000AACC (LSB) (normal NEC)
(MSB) 0x00AAaaCC (LSB) (extended NEC, address check wrong)
(MSB) 0xaaAAccCC (LSB) (32-bit NEC, command check wrong)
Note that the address byte order in 32-bit NEC scancodes is different to
that of the extended NEC scancodes. I chose this way as it maintains the
order of the bits in the address/command fields, and CC is clearly
intended to be the LSB of the command if the TiVo codes are anything to
go by so it makes sense for AA to also be the LSB.
The TiVo keymap is updated accordingly.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: linux-media@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add and document a generic sysfs based scancode filtering interface for
making use of IR data matching hardware to filter out uninteresting
scancodes. Two filters exist, one for normal operation and one for
filtering scancodes which are permitted to wake the system from suspend.
The following files are added to /sys/class/rc/rc?/:
- filter: normal scancode filter value
- filter_mask: normal scancode filter mask
- wakeup_filter: wakeup scancode filter value
- wakeup_filter_mask: wakeup scancode filter mask
A new s_filter() driver callback is added which must arrange for the
specified filter to be applied at the right time. Drivers can convert
the scancode filter into a raw IR data filter, which can be applied
immediately or later (for wake up filters).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: linux-media@vger.kernel.org
Cc: Rob Landley <rob@landley.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 1d184b0bc1 ([media] media: rc: add raw decoder for Sharp
protocol) added a new raw IR decoder for the sharp protocol, but didn't
add the code to load the module at init as is done for other raw
decoders, so add that code now.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add USB ID [2040:f900] for Hauppauge WinTV-MiniStick 2.
Device is build upon IT9135 chipset.
Tested-by: Stefan Becker <schtefan@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are reports[1] that on some motherboards loading the nuvoton-cir
disables PS/2 keyboard input. This is caused by an erroneous write of
CIR_INTR_MOUSE_IRQ_BIT to ACPI control register.
According to datasheet the write enables mouse power management event
interrupts which will probably have ill effects if the motherboard has
only one PS/2 port with keyboard in it.
The cir hardware does not need mouse interrupts to function and should
not touch them. This patch removes the illegal writes and registry
definitions.
[1] http://ubuntuforums.org/showthread.php?t=2106277&p=12461912&mode=threaded#post12461912
Reported-by: Bruno Maire <bruno.maire@besonet.ch>
Tested-by: Bruno Maire <bruno.maire@besonet.ch>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When tuning to 10818V on Astra 28E2, the system tunes to 11343V
instead. This is a regression in the S471 driver introduced with the
changeset: b43ea8068d [media] cx23885:
Fix TeVii S471 regression since introduction of ts2020.
Suggested-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Joakim Hernberg <jhernberg@alchemy.lu>
Tested-by: Mark Clarkstone <hello@markclarkstone.co.uk>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
A number of recent bug reports involve usb_submit_urb() failing which was
only reported with debug parameter on. In addition, remove custom debug
function.
[m.chehab@samsung.com: patch rebased, as one of the patches on this
series need changes]
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit e63b009d6e "em28xx-i2c: Fix error code for I2C error transfers"
changed the code to return -ETIMEDOUT on all unknown errors.
But the proper error code for unknown errors is -EIO.
So only report -ETIMEDOUT in case of the errors 0x02 and 0x04, which
are according to Mauro Carvalho Chehab's tests related to i2c clock
stretching and return -EIO for the rest.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit d845fb3ae5 "em28xx-i2c: add timeout debug information if i2c_debug enabled"
has added wrong error descriptions for -ENXIO.
The strings are also missing terminating newline characters, which breaks the
output format.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This avoids the unnecessary temporary registration of a dummy V4L2 clock.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since commit e63b009d6e the returned error code in case of not connected/responding
i2c clients is ENXIO isntead of ENODEV, which causes several error messages on
sensor probing.
Fix the i2c return value checks on sensor probing to silence these warnings.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Otherwiese the core refuses to unregister the clock and the following warning
appears in the system log:
"WARNING: ... at drivers/media/v4l2-core/v4l2-clk.c:231 v4l2_clk_unregister+0x8a/0x90 [videodev]()
v4l2_clk_unregister(): Refusing to unregister ref-counted 11-0030:mclk clock!"
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
dev->adev.users always needs to be increased when snd_em28xx_capture_open() is
called and succeeds.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a raw decoder for the Sharp protocol. It uses a pulse distance
modulation with a pulse of 320us and a bit period of 2ms for a logical 1
and 1ms for a logical 0. The first part of the message consists of a
5-bit address, an 8-bit command, and two other bits, followed by a 40ms
gap before the echo message which is an inverted version of the main
message except for the address bits.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: linux-media@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since v3.12, specifically 153a60bb0f ([media] rc: add feedback led
trigger for rc keypresses), an LED trigger is activated on IR keydown
whether or not a keypress is generated (i.e. even if there's no matching
keycode). However the repeat and keyup logic isn't used unless there is
a keypress, which results in non-keypress keydown events turning on the
LED and not turning it off again.
On the assumption that the intent was for the LED only to light up on
valid key presses (you probably don't want it lighting up for the wrong
remote control for example), move the led_trigger_event() call inside
the keycode check.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix sparse warning:
drivers/media/rc/rc-main.c:27:1: sparse: symbol 'ir_core_dev_number' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix sparse warning:
drivers/media/usb/em28xx/em28xx-cards.c:69:1: sparse: symbol 'em28xx_devused' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The VESA standard added a version 2 of the reduced blanking formula.
Note in the comment that this is not yet supported by the v4l2_detect_cvt
function. Obviously this should be implemented eventually, but for now add
this as a reminder.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fixes all style warnings from scripts/checkpatch -f
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
module_usb_driver eliminates the boilerplate and makes the code simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This applies to HDMI-map register 0x69.
So far we have been using HPA manual mode.
This way we had control of HPA which could be
set after EDID had been programmed.
Using a Mac Mini with mini-displayport to DVI-D converter as source
caused the adv7842 to lock up and fail to detect any further signals.
After experimenting with different configurations it was found that
using the HPA auto mode and in addition letting RX-termination
be controlled by HPA prevented this error from occuring.
I was not able to re-create this problem on the adv7604.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Clear any pending AVI checksum-errors.
To be able to display last received AVI.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Incorrect registers used for pixelclock read-out.
Same registers as for adv7604 which actually gave an almost
correct read-out, even they are not documented for adv7842.
Corrected deep-color pixel-clock correction.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the input signal is DVI-D and quantization range is RGB full range,
gain and offset must be adjusted to get the right range on the output.
Copied and adopted from adv7604.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
I came across this while checking the kernel use of V4L2_CTRL_FLAG_DISABLED.
This flag should not be used with the control framework. Instead, just don't
add the control at all.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This define uses the deprecated interruptible_sleep_on_timeout
function. Since this define is unused anyway we just remove it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
usbtv-video.c needs module.h. So move the module.h include from usbtv-core.c to usbtv.h,
that way both core.c and video.c have it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Round off image width to nearest 8 (GTF_CELL_GRAN)
A source sending a GTF (Generalized Timing Formula) format have no means of
signalling image width. The assumed aspect ratio may result in an odd image
width but according to the standard image width should be in multiple of 8.
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
cppcheck reported memory leak in device_authorizatio()
within hdpvr-core.c.
When the debug option is specified and the code jump to
"unlock:" label, print_buf was not freed.
Confirm the module succesfully compiled without error.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add USB ID [2040:f900] for Hauppauge WinTV-MiniStick 2.
Device is build upon IT9135 chipset.
Tested-by: Stefan Becker <schtefan@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix the following build error:
drivers/media/usb/dvb-usb-v2/
mxl111sf-tuner.h:72:9: error: expected ‘;’, ‘,’ or ‘)’ before ‘struct’
struct mxl111sf_tuner_config *cfg)
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
mxl111sf_read_reg takes an address of a variable to write to as an argument.
drivers/media/usb/dvb-usb-v2/mxl111sf-gpio.c:mxl111sf_config_pin_mux_modes
passes several uninitialized stack variables to this routine, expecting
them to be filled in. In the event that something unexpected happens when
reading from the chip, we end up doing a pr_debug of the value passed in,
revealing whatever garbage happened to be on the stack.
Change the pr_debug to match what happens in the 'success' case, where we
assign buf[1] to *data.
Spotted with Coverity (Bugs 731910 through 731917)
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Don't use '&state->priv->i2c->dev' reference to device because
state is still 'NULL'. Use '&i2c->dev' instead.
This bug has been reported by scan.coverity.com
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: vger@stable.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
At this point of the execution in the function cx24117_attach()
demod cannot be '0'. In that case the function returns earlier
with an error value ('NULL'). Remove the if statement.
This error has been reported by scan.coverity.com
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
I am no longer available at the kernellabs.com or m1k.net email
addresses. Update each instance of my email to my linuxtv.org
account.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds a test preventing streamon() if there is no buffer
ready.
Without this patch, a user could call streamon() before
preparing any buffer. This leads to a situation where if he calls
close() before calling streamoff() the device is kept streaming.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This reverts commit a242f42610.
That commit actually caused deadlocks, rather then fixing them.
If ext_lock is set to NULL (otherwise videobuf_queue_lock doesn't do
anything), then you get this deadlock:
The driver's mmap function calls videobuf_mmap_mapper which calls
videobuf_queue_lock on q. videobuf_mmap_mapper calls __videobuf_mmap_mapper,
__videobuf_mmap_mapper calls videobuf_vm_open and videobuf_vm_open
calls videobuf_queue_lock on q (introduced by above patch): deadlocked.
This affects drivers using dma-contig and dma-vmalloc. Only dma-sg is
not affected since it doesn't call videobuf_vm_open from __videobuf_mmap_mapper.
Most drivers these days have a non-NULL ext_lock. Those that still use
NULL there are all fairly obscure drivers, which is why this hasn't been
seen earlier.
Since everything worked perfectly fine for many years I prefer to just
revert this patch rather than trying to fix it. videobuf is quite fragile
and I rather not touch it too much. Work is (slowly) progressing to move
everything over to vb2 or at the very least use non-NULL ext_lock in
videobuf.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v3.11 and up
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Reported-by: Pete Eberlein <pete@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is required so that we give up the last reference to the device.
Remove the kfree() because the put_device() call will actually call
release_sub_device which in turn kfrees the device.
Signed-off-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Enclose the runtime PM helpers in #ifdef CONFIG_PM_RUNTIME/#endif
to avoid following compile warning when CONFIG_PM_RUNTIME is disabled:
CC drivers/media/platform/exynos4-is/fimc-lite.o
drivers/media/platform/exynos4-is/fimc-lite.c:1591:12: warning: ‘fimc_lite_runtime_resume’ defined but not used [-Wunused-function]
drivers/media/platform/exynos4-is/fimc-lite.c:1599:12: warning: ‘fimc_lite_runtime_suspend’ defined but not used [-Wunused-function]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Enclose the runtime PM helpers in #ifdef CONFIG_PM_RUNTIME/#endif
to avoid following compile warning when CONFIG_PM_RUNTIME is disabled:
CC drivers/media/platform/exynos4-is/fimc-core.o
drivers/media/platform/exynos4-is/fimc-core.c:1040:12: warning: ‘fimc_runtime_resume’ defined but not used
drivers/media/platform/exynos4-is/fimc-core.c:1057:12: warning: ‘fimc_runtime_suspend’ defined but not used
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ensure clk_disable() is called on error paths only when clk_enable()
was previously called.
This fixes following build warning:
.../media-git/drivers/media/platform/exynos4-is/fimc-lite.c: In function 'fimc_lite_probe':
.../media-git/drivers/media/platform/exynos4-is/fimc-lite.c:1583:1: warning: label 'err_sd' defined but not used [-Wunused-label]
Reported-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
NV12 format entries in the sjpeg_formats array had wrong
colplanes, depth and v_align values.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Using variable length array in s5k5baf_write_arr_seq caused
an implicit assumption that i2c sequences should be short.
The patch rewrites the function so it can handle sequences
of any length and does not use variable length array.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We have two APIs for compatiblity timespec/val, with confusingly
similar names. compat_(get|put)_time(val|spec) *do* handle the case
where COMPAT_USE_64BIT_TIME is set, whereas
(get|put)_compat_time(val|spec) do not. This is an accident waiting
to happen.
Clean it up by favoring the full-service version; the limited version
is replaced with double-underscore versions static to kernel/compat.c.
A common pattern is to convert a struct timespec to kernel format in
an allocation on the user stack. Unfortunately it is open-coded in
several places. Since this allocation isn't actually needed if
COMPAT_USE_64BIT_TIME is true (since user format == kernel format)
encapsulate that whole pattern into the function
compat_convert_timespec(). An equivalent function should be written
for struct timeval if it is needed in the future.
Finally, get rid of compat_(get|put)_timeval_convert(): each was only
used once, and the latter was not even doing what the function said
(no conversion actually was being done.) Moving the conversion into
compat_sys_settimeofday() itself makes the code much more similar to
sys_settimeofday() itself.
v3: Remove unused compat_convert_timeval().
v2: Drop bogus "const" in the destination argument for
compat_convert_time*().
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Mateusz Guzik <mguzik@redhat.com>
Cc: Rafael Aquini <aquini@redhat.com>
Cc: Davidlohr Bueso <davidlohr@hp.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Tested-by: H.J. Lu <hjl.tools@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Pull media updates from Mauro Carvalho Chehab:
- a new jpeg codec driver for Samsung Exynos (jpeg-hw-exynos4)
- a new dvb frontend for ds2103 chipset (m88ds2103)
- a new sensor driver for Samsung S5K5BAF UXGA (s5k5baf)
- new drivers for R-Car VSP1
- a new radio driver: radio-raremono
- a new tuner driver for ts2022 chipset (m88ts2022)
- the analog part of em28xx is now a separate module that only
load/runs if the device is not a pure digital TV device
- added a staging driver for bcm2048 radio devices
- the omap 2 video driver (omap24xx) was moved to staging. This driver
is for an old hardware and uses a deprecated Kernel internal API. If
nobody cares enough to fix it, it would be removed on a couple Kernel
releases
- the sn9c102 driver was moved to staging. This driver was replaced by
gspca, and disabled on some distros, as almost all devices are known
to work properly with gspca. It should be removed from kernel on a
couple Kernel releases
- lots of driver fixes, improvements and cleanups
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (421 commits)
[media] media: v4l2-dev: fix video device index assignment
[media] rc-core: reuse device numbers
[media] em28xx-cards: properly initialize the device bitmap
[media] Staging: media: Fix line length exceeding 80 characters in as102_drv.c
[media] Staging: media: Fix line length exceeding 80 characters in as102_fe.c
[media] Staging: media: Fix quoted string split across line in as102_fe.c
[media] media: st-rc: Add reset support
[media] m2m-deinterlace: fix allocated struct type
[media] radio-usb-si4713: fix sparse non static symbol warnings
[media] em28xx-audio: remove needless check before usb_free_coherent()
[media] au0828: Fix sparse non static symbol warning
Revert "[media] go7007-usb: only use go->dev after allocated"
[media] em28xx-audio: provide an error code when URB submit fails
[media] em28xx: fix check for audio only usb interfaces when changing the usb alternate setting
[media] em28xx: fix usb alternate setting for analog and digital video endpoints > 0
[media] em28xx: make 'em28xx_ctrl_ops' static
em28xx-alsa: Fix error patch for init/fini
[media] em28xx-audio: flush work at .fini
[media] drxk: remove the option to load firmware asynchronously
[media] em28xx: adjust period size at runtime
...
<<
Switch mpc512x to the common clock framework and adapt mpc512x
drivers to use the new clock driver. Old PPC_CLOCK code is
removed entirely since there are no users any more.
>>
The side effect of commit 1056e4388b ("v4l2-dev: Fix race condition on
__video_register_device") is the increased number of index value assigned
on video_device registration. Before that commit video_devices were
numbered from 0, after it, the indexes starts from 1, because get_index()
always count the device, which is being registered. Some device drivers
rely on video_device index number for internal purposes, i.e. s5p-mfc
driver stopped working after that patch. This patch restores the old method
of numbering the video_device indexes.
Cc: stable@vger.kernel.org # for v3.12
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Ricardo Ribalda <ricardo.ribalda@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
entirely of new platform/driver support. There are some conversions of
existing drivers to the common-clock Device Tree binding, and a few
non-critical fixes to the framework.
Due to an entirely unnecessary cyclical dependency with the arm-soc tree
this pull request is broken into two pieces. The second piece will be
sent out after arm-soc sends you the pull request that merged in core
support for the HiSilicon 3620 platform. That same pull request from
arm-soc depends on this pull request to merge in those HiSilicon bits
without causing build failures.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=Hh66
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.14-part1' of git://git.linaro.org/people/mike.turquette/linux
Pull clk framework changes from Mike Turquette:
"The first half of the clk framework pull request is made up almost
entirely of new platform/driver support. There are some conversions
of existing drivers to the common-clock Device Tree binding, and a few
non-critical fixes to the framework.
Due to an entirely unnecessary cyclical dependency with the arm-soc
tree this pull request is broken into two pieces. The second piece
will be sent out after arm-soc sends you the pull request that merged
in core support for the HiSilicon 3620 platform. That same pull
request from arm-soc depends on this pull request to merge in those
HiSilicon bits without causing build failures"
[ Just did the ARM SoC merges, so getting ready for the second clk tree
pull request - Linus ]
* tag 'clk-for-linus-3.14-part1' of git://git.linaro.org/people/mike.turquette/linux: (97 commits)
devicetree: bindings: Document qcom,mmcc
devicetree: bindings: Document qcom,gcc
clk: qcom: Add support for MSM8660's global clock controller (GCC)
clk: qcom: Add support for MSM8974's multimedia clock controller (MMCC)
clk: qcom: Add support for MSM8974's global clock controller (GCC)
clk: qcom: Add support for MSM8960's multimedia clock controller (MMCC)
clk: qcom: Add support for MSM8960's global clock controller (GCC)
clk: qcom: Add reset controller support
clk: qcom: Add support for branches/gate clocks
clk: qcom: Add support for root clock generators (RCGs)
clk: qcom: Add support for phase locked loops (PLLs)
clk: qcom: Add a regmap type clock struct
clk: Add set_rate_and_parent() op
reset: Silence warning in reset-controller.h
clk: sirf: re-arch to make the codes support both prima2 and atlas6
clk: composite: pass mux_hw into determine_rate
clk: shmobile: Fix MSTP clock array initialization
clk: shmobile: Fix MSTP clock index
ARM: dts: Add clock provider specific properties to max77686 node
clk: max77686: Register OF clock provider
...
Before changeset d8b4b5822f, the remote controller device numbers
were released when the device were unregistered. That helped to maintain
some sanity, as, when USB devices are replugged, the remote controller
would get the same number.
Restore the same behaviour.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some of the SOCs hold the IRB IP in softreset state by default.
For this IP to work driver needs to bring it out of softreset.
This patch adds support to reset the IP via reset framework.
Without this patch the driver can not work with SoCs which holds the IP
in softreset.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
'xt' points to a dma_interleaved_template and not a dma_async_tx_descriptor.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fixes the following sparse warnings:
drivers/media/radio/si4713/radio-usb-si4713.c:226:31: warning:
symbol 'start_seq' was not declared. Should it be static?
drivers/media/radio/si4713/radio-usb-si4713.c:291:29: warning:
symbol 'command_table' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
usb_free_coherent() is safe with NULL addr and this check is
not required.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fixes the following sparse warning:
drivers/media/usb/au0828/au0828-dvb.c:36:5: warning:
symbol 'preallocate_big_buffers' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of just saying:
[ 1646.412419] em2882/3 #0: submit of audio urb failed
Print the reason why it failed, to help debugging and fixing it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Previously, we've been assuming that the video endpoints are always at usb
interface 0. Hence, if vendor audio endpoints are provided at a separate
interface, they were supposed to be at interface number > 0.
Instead of checking for (interface number > 0) to determine if an interface
is a pure audio interface, dev->is_audio_only should be checked.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The current code assumes that the analog + digital video endpoints are always at
interface number 0 when changing the alternate setting.
This seems to work fine for most existing devices.
However, at least the SpeedLink VAD Laplace webcam has the video endpoint on
interface number 3 (which fortunately doesn't cause any trouble because ist uses
bulk transfers only).
We already consider the actual interface number for audio endpoints, so
rename the the audio_ifnum variable and use it for all device types.
Also get get rid of a pointless (ifnum < 0) in em28xx-audio.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
sparse warnings: (new ones prefixed by >>)
>> drivers/media/usb/em28xx/em28xx-video.c:1151:28: sparse: symbol 'em28xx_ctrl_ops' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If something bad happens during init, we free the card data.
However, we still keep it initialized, causing some dependent
code to be called at .fini.
Fix it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The option to load firmware asynchronously were added due to
a requirement with a few versions of udev. It turns that this was
a bad idea and caused regressions on drxk-based devices.
So, we end by only letting the firmware to be loaded syncronously
everywhere.
So, let's remove the bad code.
This patch partially reverts the changeset 8e30783b0b.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
While the current hardcoded period is ok for the current values,
we may latter change the driver to work with different bit rates
or with different latencies than 64ms.
So, adust the period size at runtime.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that everything is extension, the usb disconnect logic should
be the same.
While here, fix the device name.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
That helps to identify if something fails and explain why em28xx
struct is not freed (if it ever happens).
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
URBs might be in usage. Disconnect the device before freeing
them.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Alsa has an special non-negative return code to indicate device removal
at snd_em28xx_capture_pointer(). Use it, instead of an error code.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove some dead code from em28xx_v4l2_fini() and fix the leaking of the video,
vbi and radio video_device struct memories.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the usb device is disconnected, the resources are no longer available,
so there is no reason to keep them registered.
This will also fix the various sysfs group removal warnings which we can see
since kernel 3.13.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
v4l2_ctrl_handler_free() and v4l2_device_unregister() are currently only called
when the last user closes the device and the device is already disconnected.
But that's wrong, we need to call these functions whenever the em28xx-v4l
extension is closed and we can already do this if the device is still opened
by some users.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
- bail out on unsupported VFL_TYPE
- em28xx_set_mode() needs to be called for VBI and radio mode, too
- em28xx_wake_i2c() needs to be called for VBI and radio mode, too
- em28xx_resolution_set() also needs to be called for VBI
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In file included from /devel/v4l/temp/include/asm-generic/page.h:23:0,
from /devel/v4l/temp/arch/c6x/include/asm/page.h:9,
from /devel/v4l/temp/include/asm-generic/io.h:14,
from arch/c6x/include/generated/asm/io.h:1,
from /devel/v4l/temp/drivers/media/radio/tea575x.c:23:
/devel/v4l/temp/arch/c6x/include/asm/setup.h:17:27: error: unknown type name ‘phys_addr_t’
extern int c6x_add_memory(phys_addr_t start, unsigned long size);
It seems that, on such arch, the includes from asm/ should be
after the ones from linux/.
The proper fix would be to patch the arch files, but, as
this fix is trivial, apply it. Also, we generally put the
asm includes after the linux ones, anyway.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/dib8000.c: In function 'dib8000_get_time_us':
drivers/media/dvb-frontends/dib8000.c:3957: warning: 'interleaving' may be used uninitialized in this function
drivers/media/dvb-frontends/dib8000.c:3956: warning: 'rate_denum' may be used uninitialized in this function
Those are actually false positives, but it doesn't hurt cleaning them.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When compiling with avr32, it gets those errors:
drivers/media/dvb-frontends/dib8000.c: In function 'dib8000_get_stats':
drivers/media/dvb-frontends/dib8000.c:4121: warning: integer constant is too large for 'long' type
Fix integer representation to avoid overflow.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This function isn't used nowhere outside the same .c file.
Fixes this warning:
drivers/media/radio/si4713/radio-usb-si4713.c:418:5: warning: no previous prototype for 'si4713_register_i2c_adapter' [-Wmissing-prototypes]
int si4713_register_i2c_adapter(struct si4713_usb_device *radio)
^
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix two warns below, by commenting the unused code:
drivers/media/platform/sh_vou.c: In function 'sh_vou_configure_geometry':
drivers/media/platform/sh_vou.c:446:49: warning: variable 'height_max' set but not used [-Wunused-but-set-variable]
unsigned int black_left, black_top, width_max, height_max,
^
drivers/media/platform/sh_vou.c: In function 'sh_vou_isr':
drivers/media/platform/sh_vou.c:1056:13: warning: variable 'side' set but not used [-Wunused-but-set-variable]
static int side;
^
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Added command line parameter preallocate_big_buffers so that the digital
transfer buffers can be allocated when the driver is registered. They
do not have to be allocated every time a feed is started.
Signed-off-by: Tim Mester <tmester@ieee.org>
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Free what was allocated if there is a failure allocating
transfer buffers.
Stop the feed on a start feed error. The stop feed is not always called
if start feed fails. If the feed is not stopped on error, then the driver
will be stuck so that it can never start feeding again.
[m.chehab@samsung.com: CodingStyle cleanup]
Signed-off-by: Tim Mester <tmester@ieee.org>
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add v4l2 controls to set desired profile for VP8 encoder.
Acceptable levels for VP8 encoder are
0: Version 0
1: Version 1
2: Version 2
3: Version 3
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
s5p_mfc_get_node_type() relies on get_index() helper function, which in
turn relies on video_device index numbers assigned on driver
registration. All this code is not really needed, because there is
already access to respective video_device structures via common
s5p_mfc_dev structure. This fixes the issues introduced by patch
1056e4388b ("v4l2-dev: Fix race condition
on __video_register_device"), which has been merged in v3.12-rc1.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Antti Palosaari