So far we only power well enabling was synchronous not disabling. Since
we don't exactly know how the firmware (both DMC and PCU) synchronizes
against the actual power well state during DC transitions, make the
disabling also synchronous.
CC: Mika Kuoppala <mika.kuoppala@linux.intel.com>
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-6-git-send-email-imre.deak@intel.com
DMC forces on power well 1 and the misc IO power well by setting the
corresponding request bits both in the BIOS and the DEBUG power well
request registers. This is somewhat unexpected since the firmware should
really just save and restore state but not alter it. We also depend on
being able to disable power well 1, and the misc IO power well before
entering S3/S4 on BXT and SKL or entering DC9 on BXT. To fix this make
sure these request bits are cleared whenever we want to disable the
given power wells.
On SKL there is another twist where the firmware also clears the power
well 1 request bit in HSW_POWER_WELL_DRIVER (but not that of the misc IO
power well). This happens to not cause a problem due to the forced-on
request bits in the other request registers.
I've filed a bug about all this, but fixing that may take a while and
having this sanity check in place makes sense even for future firmware
versions.
At the same time also check the KVMR request bits. I haven't seen this
being altered, but we don't expect any request bits in here either, so
sanitize this register as well.
v2:
- Apply the workaround on SKL as well. I noticed the related failure
from the CI report, later Patrik also reported seeing it on his
machine.
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459851965-6137-1-git-send-email-imre.deak@intel.com
The registers frobbed by vlv_init_display_clock_gating() libve inside
the disp2d power well, so frobbing them while the power well is down
results in unclaimed register access warning (and of course the values
won't stick). Let's do this setup after we know the power well is
enabled.
It's also worth noting that DSPCLK_GATE_D and CBR1_VLV lose their state
when the power well goes down, but fortunately the values we've been
writing are actually the reset defaults.
MI_ARB_VLV actually retains its value even if the power well was turned
off, we just can't access it while the power well is down.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94164
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-9-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
dev_priv is what the macro works hard to extract, pass it directly.
> sed 's/\([A-Z].*(dev_priv\)->dev)/\1)/g'
v2:
- Include all wrapper macros too (Chris)
v3:
- Include sed cmdline (Chris)
v4:
- Break long line
- Rebase
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460016485-8089-1-git-send-email-joonas.lahtinen@linux.intel.com
The BXT display connections have DSI transcoders A and C that can be
muxed to any pipe, not unlike the eDP transcoder. Add the notion of DSI
transcoders.
The "normal" transcoders A, B and C are not used with BXT DSI, so care
must be taken to avoid accessing those registers with DSI transcoders in
the hardware state readout, modeset, and generally everywhere.
v2: addressing comments by Ville:
- rename the dsi get config function to hsw_get_dsi_transcoder_state
- rebase onto the higher level split of pipe/transcoder functions
- use more has_dsi_encoder as we can now because of the above,
with no need to look at the transcoder so much
- rename IS_DSI_TRANSCODER to transcoder_is_dsi
- use the above a bit more instead of comparing to < TRANSCODER_EDP
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/299740536b7941e31b2744f3ce34f7afe936a771.1458313400.git.jani.nikula@intel.com
The DSI power domain was missing from BXT power well 1 definitions,
failing to get the power well for DSI transcoders. As pipe A is in the
same power well as DSI transcoders, the problem should only occur with
pipes B and C.
According to Ville, this is basically a nop since pw1 is under dmc
control. But given that we still have this stuff defined here, it's
clearly correct to include DSI here.
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Deepak M <m.deepak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457463656-29357-1-git-send-email-jani.nikula@intel.com
In commit 1e657ad7 we moved the last step of firmware initialization to
skl_display_core_init(), where it will be run only during system resume,
but not during driver loading. Since this init step needs to be done
whenever we program the firmware fix this by moving the initialization
to the end of intel_csr_load_program().
While at it simplify a bit csr_load_work_fn().
This issue prevented DC5/6 transitions, this change will re-enable those.
v2:
- remove debugging left-over and redundant comment in csr_load_work_fn()
Fixes: 1e657ad7a4 ("drm/i915/gen9: Write dc state debugmask bits only once")
CC: Mika Kuoppala <mika.kuoppala@intel.com>
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457121461-16729-1-git-send-email-imre.deak@intel.com
Disabling the DC states when it's already disabled is a valid scenario,
for example during HW state sanitization during driver loading and
resuming or when DC states are disabled via the i915.enable_dc or
disable_power_well option.
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456778945-5411-4-git-send-email-imre.deak@intel.com
If power well support is disabled via the i915.disable_power_well module
option we should never enable DC states. Currently we would enable DC
states even in this case during system suspend, where we need to disable
all power wells regardless of the disable_power_well option.
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456778945-5411-3-git-send-email-imre.deak@intel.com
We can simplify the conditions selecting the target DC state during
runtime by calculating the allowed DC states in advance during driver
loading. This also makes it easier to disable DC states depending on the
i915.disable_power_well module option, added in the next patch.
v2:
- Print a debug message if the requested max DC value was adjusted due
to a platform limit. Also debug print the calculated mask value. (Patrik)
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456778945-5411-2-git-send-email-imre.deak@intel.com
During system suspend we need to first disable power wells then
unitialize the display core. In case power well support is disabled we
did this in the wrong order, so fix this up.
Fixes: d314cd43 ("drm/i915: fix handling of the disable_power_well module option")
CC: stable@vger.kernel.org
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456778945-5411-1-git-send-email-imre.deak@intel.com
commit 0973128002
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Feb 17 14:17:42 2016 +0200
drm/i915: Add helper to get a display power ref if it was already enabled
left the rpm wakelock assertions unbalanced if CONFIG_PM was disabled as
intel_runtime_pm_get_if_in_use() would return true without incrementing
the local bookkeeping required for the assertions.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
CC: Mika Kuoppala <mika.kuoppala@intel.com>
CC: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456434628-22574-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Imre Deak <imre.deak@intel.com>
Starting from BDW the DE_PIPE interrupts for pipe B and C belong to the
relevant display power well. So we should make sure we've finished
processing them before turning off the power well.
The pipe interrupts shouldn't really happen at this point anymore since
we've already shut down the planes/pipes/whatnot, but being a bit
paranoid shouldn't hurt.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455907651-16397-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
After we've told the irq code we don't want to handle display irqs
anymore, we must make sure any display irq handling already
kicked off has finished before we actually turn off the power well.
I wouldn't expect PIPESTAT based interrupts to occur anymore since
vblanks/page flips/gmbus/etc should all be quiescent at this point.
But at least hotplug interrupts could still occur. Hotplug
interrupts may also kick off the workqueue based hotplug processing,
but that code should take the required power domain references
itself, so there shouldn't be any need to synchronize with the
hotplug processing from the power well code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455900112-15387-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Cores need to be included into the debug mask. We don't exactly
know what it does but the spec says it must be enabled. So obey.
v2: Cores should be only set for BXT (Imre, Art)
Cc: Imre Deak <imre.deak@intel.com>
Cc: Runyan, Arthur J <arthur.j.runyan@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455877564-5128-1-git-send-email-mika.kuoppala@intel.com
It has been observed that sometimes disabling the dc6 fails
and dc6 state pops back up, brief moment after disabling. This
has to be dmc save/restore timing issue or other bug in the
way dc states are handled.
Try to work around this issue as we don't have firmware fix
yet available. Verify that the value we wrote for the dmc sticks,
and also enforce it by rewriting it, if it didn't.
v2: Zero rereads on rewrite for extra paranoia (Imre)
Testcase: kms_flip/basic-flip-vs-dpms
References: https://bugs.freedesktop.org/show_bug.cgi?id=93768
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455811089-27884-1-git-send-email-mika.kuoppala@intel.com
The DMC can incorrectly run off and allow DC states on it's own. We
don't know the root-cause for this yet but this patch makes it more
visible.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455808874-22089-2-git-send-email-mika.kuoppala@intel.com
We have many places in the code where we check if a given display power
domain is enabled and if so access registers backed by this power
domain. We assumed that some modeset lock will prevent the power
reference from vanishing in the middle of the HW access, but this
assumption doesn't always hold. In such cases we get either the wakeref
not held, or an unclaimed register access error message. To fix this in
a future-proof way that's independent of other locks wrap any such
access with a get_ref_if_enabled()/put_ref() pair.
Kudos to Ville and Joonas for the ideas of this new interface.
v2:
- init the power_domains ptr when declaring it everywhere (Joonas)
v3:
- don't report the device to be powered if runtime PM is disabled
CC: Mika Kuoppala <mika.kuoppala@intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455711462-7442-1-git-send-email-imre.deak@intel.com
Move the ddi buffer translation programming to occur from the encoder
.pre_enable() hook, for just the ddi port we are enabling. Previously
we used to reprogram the translations for all ddi ports during
init and during power well enabling.
v2: s/intel_prepare_ddi_buffers/intel_prepare_ddi_buffer/ (Daniel)
Resolve conflicts due to dev_priv->atomic_cdclk_freq
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When adding IS_KABYLAKE definition I didn't included the
DC states related because I was planing to include them
with the patch that fixes DMC firmware loading, but I
forgot them.
Meanwhile this runtime pm code changed a lot for
Skylake.
Well, I didn't expect that this would crash the machine
and I just noticed now that Sarah warned me our driver
wasn't working. Thanks Sarah.
Michel had found the main error first and his
fix had better details on the history and got
merged already:
commit 16fbc291cb
Author: Michel Thierry <michel.thierry@intel.com>
Date: Wed Jan 6 12:08:36 2016 +0000
drm/i915/kbl: Enable PW1 and Misc I/O power wells
This one is a follow-up adding the other remaining
missing pieces.
v2: Rebased on top of Michel's patch as explained above.
Cc: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452214179-22361-1-git-send-email-rodrigo.vivi@intel.com
My kbl stopped working because of this.
Fixes regression from
commit 2f693e28b8
Author: Damien Lespiau <damien.lespiau@intel.com>
Date: Wed Nov 4 19:24:12 2015 +0200
drm/i915: Make turning on/off PW1 and Misc I/O part of the init/fini
sequences
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452082116-16770-1-git-send-email-michel.thierry@intel.com
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
pm_runtime_{use,dont_use}_autosuspend() controls whether the device's
sysfs power/autosuspend_delay_ms file is writeable or returns -EIO on
access to user space. Since
commit 25b181b46e
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Dec 17 13:44:56 2015 +0200
drm/i915: get a permanent RPM reference on platforms w/o RPM support
this sysfs file is writeable also on platforms without RPM support, but
userspace (at least IGT) depends on this file being unchangable to
determine whether the device supports runtime PM at all. So restore the
old behavior.
This gets rid of igt/pm_rpm failures on old platforms without RPM
support, where the test should be skipped.
Testcase: igt/pm_rpm/basic-rte
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450371873-878-1-git-send-email-imre.deak@intel.com
In some cases we want to check whether we hold an RPM wakelock reference
for the whole duration of a sequence. To achieve this add a new RPM
atomic sequence counter that we increment any time the wakelock refcount
drops to zero. Check whether the sequence number stays the same during
the atomic section and that we hold the wakelock at the beginning of the
section.
Motivated by Chris.
v2-v3:
- unchanged
v4:
- swap the order of atomic_read() and assert_rpm_wakelock_held() in
assert_rpm_atomic_begin() to avoid race
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-10-git-send-email-imre.deak@intel.com
With this change we have the corresponding wake lock checks in both the
rpm get and put functions.
v2-v3:
- unchanged
v4:
- keep the corresponding check in the get helper (Chris)
v5:
- add a note to the commit message that with this change we have the
checks both in the rpm get and put functions (Joonas)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-9-git-send-email-imre.deak@intel.com
Atm, we assert that the device is not suspended until the point when the
device is truly put to a suspended state. This is fine, but we can catch
more problems if we check that RPM refcount is non-zero. After that one
drops to zero we shouldn't access the device any more, even if the actual
device suspend may be delayed. Change assert_rpm_wakelock_held()
accordingly to check for a non-zero RPM refcount in addition to the
current device-not-suspended check.
For the new asserts to work we need to annotate every place explicitly in
the code where we expect that the device is powered. The places where we
only assume this, but may not hold an RPM reference:
- driver load
We assume the device to be powered until we enable RPM. Make this
explicit by taking an RPM reference around the load function.
- system and runtime sudpend/resume handlers
These handlers are called when the RPM reference becomes 0 and know the
exact point after which the device can get powered off. Disable the
RPM-reference-held check for their duration.
- the IRQ, hangcheck and RPS work handlers
These handlers are flushed in the system/runtime suspend handler
before the device is powered off, so it's guaranteed that they won't
run while the device is powered off even though they don't hold any
RPM reference. Disable the RPM-reference-held check for their duration.
In all these cases we still check that the device is not suspended.
These explicit annotations also have the positive side effect of
documenting our assumptions better.
This caught additional WARNs from the atomic modeset path, those should
be fixed separately.
v2:
- remove the redundant HAS_RUNTIME_PM check (moved to patch 1) (Ville)
v3:
- use a new dedicated RPM wakelock refcount to also catch cases where
our own RPM get/put functions were not called (Chris)
- assert also that the new RPM wakelock refcount is 0 in the RPM
suspend handler (Chris)
- change the assert error message to be more meaningful (Chris)
- prevent false assert errors and check that the RPM wakelock is 0 in
the RPM resume handler too
- prevent false assert errors in the hangcheck work too
- add a device not suspended assert check to the hangcheck work
v4:
- rename disable/enable_rpm_asserts to disable/enable_rpm_wakeref_asserts
and wakelock_count to wakeref_count
- disable the wakeref asserts in the IRQ handlers and RPS work too
- update/clarify commit message
v5:
- mark places we plan to change to use proper RPM refcounting with
separate DISABLE/ENABLE_RPM_WAKEREF_ASSERTS aliases (Chris)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1450227139-13471-1-git-send-email-imre.deak@intel.com
We don't really need to check this flag in the get/put/assert helpers,
as on platforms without RPM support we won't ever enable RPM. That means
pm.suspend will be always false and the assert will be always true.
Do this to simplify the code and to let us extend the RPM asserts to all
platforms for a better coverage.
Motivated by Ville.
v2-v3:
- unchanged
v4:
- remove the HAS_RUNTIME_PM check from intel_runtime_pm_enable() too
made possible by the previous two patches
v5:
- rebased on the previous new patch in the series that keeps
HAS_RUNTIME_PM() in intel_runtime_pm_enable() with a permanent
reference taken there
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450352931-16498-1-git-send-email-imre.deak@intel.com
Currently we disable RPM functionality on platforms that doesn't support
this by not putting/getting the RPM reference we receive from the RPM
core during driver loading/unloading respectively. This is somewhat
obscure, so make it more explicit by keeping a reference dedicated for
this particular purpose whenever the driver is loaded. This makes it
possible to remove the HAS_RUNTIME_PM() special casing from every other
places in the next patch.
v2:
- fix intel_runtime_pm_get vs. intel_runtime_pm_put in
intel_power_domains_fini()
v3:
- take only a low level RPM reference so the ref tracking asserts
continue to work (Ville)
- update the commit message
- move the patch earlier for bisectability
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450352696-16135-1-git-send-email-imre.deak@intel.com
We can make the RPM dependency on RC6 explcit in the code by taking an
actual RPM reference, instead of avoiding to drop the initial one. This
will also enable us to remove the HAS_RUNTIME_PM special casing from
more places in the next patch.
v2:
- fixed typo in commit message (Joonas)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-4-git-send-email-imre.deak@intel.com
Here are the patchset to add get_eld op to audio component for
communicating more directly between i915 and HD-audio.
Currently, the HDMI/DP audio status and ELD are notified and obtained
via the hardware-level communication over HD-audio unsolicited event
and verbs although the graphics driver holds the exactly same
information. As we already have a notification via audio component,
this is another step forward; namely, the audio driver may fetch
directly the audio status and ELD via the new component op.
The commits are based on Dave's latest drm-next branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=NShN
-----END PGP SIGNATURE-----
Merge tag 'drm-i915-get-eld' of tiwai/sound into drm-intel-next-queued
Add get_eld audio component for i915/HD-audio
Currently, the HDMI/DP audio status and ELD are notified and obtained
via the hardware-level communication over HD-audio unsolicited event
and verbs although the graphics driver holds the exactly same
information. As we already have a notification via audio component,
this is another step forward; namely, the audio driver may fetch
directly the audio status and ELD via the new component op.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
BXT power well support is not yet stable. Starting with patch
commit 9f836f9016
Author: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Date: Mon Nov 16 16:20:01 2015 +0100
drm/i915/gen9: Turn DC handling into a power well
DPMS off operations may actually cause the entire system to powerdown or
reboot. Disable power well support for now until Broxton gets fixes
similar to what we have for SKL.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
References: http://lists.freedesktop.org/archives/intel-gfx/2015-November/081037.html
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448990818-11005-1-git-send-email-matthew.d.roper@intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
drm-intel-next-2015-11-20-rebased:
4 weeks because of my vacation, so a bit more:
- final bits of the typesafe register mmio functions (Ville)
- power domain fix for hdmi detection (Imre)
- tons of fixes and improvements to the psr code (Rodrigo)
- refactoring of the dp detection code (Ander)
- complete rework of the dmc loader and dc5/dc6 handling (Imre, Patrik and
others)
- dp compliance improvements from Shubhangi Shrivastava
- stop_machine hack from Chris to fix corruptions when updating GTT ptes on bsw
- lots of fifo underrun fixes from Ville
- big pile of fbc fixes and improvements from Paulo
- fix fbdev failures paths (Tvrtko and Lukas Wunner)
- dp link training refactoring (Ander)
- interruptible prepare_plane for atomic (Maarten)
- basic kabylake support (Deepak&Rodrigo)
- don't leak ringspace on resets (Chris)
drm-intel-next-2015-10-23:
- 2nd attempt at atomic watermarks from Matt, but just prep for now
- fixes all over
* tag 'drm-intel-next-2015-11-20-merged' of git://anongit.freedesktop.org/drm-intel: (209 commits)
drm/i915: Update DRIVER_DATE to 20151120
drm/i915: take a power domain reference while checking the HDMI live status
drm/i915: take a power domain ref only when needed during HDMI detect
drm/i915: Tear down fbdev if initialization fails
async: export current_is_async()
Revert "drm/i915: Initialize HWS page address after GPU reset"
drm/i915: Fix oops caused by fbdev initialization failure
drm/i915: Fix i915_ggtt_view_equal to handle rotation correctly
drm/i915: Stuff rotation params into view union
drm/i915: Drop return value from intel_fill_fb_ggtt_view
drm/i915 : Fix to remove unnecsessary checks in postclose function.
drm/i915: add MISSING_CASE to a few port/aux power domain helpers
drm/i915/ddi: fix intel_display_port_aux_power_domain() after HDMI detect
drm/i915: Remove platform specific *_dp_detect() functions
drm/i915: Don't do edp panel detection in g4x_dp_detect()
drm/i915: Send TP1 TP2/3 even when panel claims no NO_TRAIN_ON_EXIT.
drm/i915: PSR: Don't Skip aux handshake on DP_PSR_NO_TRAIN_ON_EXIT.
drm/i915: Reduce PSR re-activation time for VLV/CHV.
drm/i915: Delay first PSR activation.
drm/i915: Type safe register read/write
...
We have serious dangling else bugs waiting to happen in our for_each_
style macros with ifs. Consider, for example,
#define for_each_power_domain(domain, mask) \
for ((domain) = 0; (domain) < POWER_DOMAIN_NUM; (domain)++) \
if ((1 << (domain)) & (mask))
If this is used in context:
if (condition)
for_each_power_domain(domain, mask);
else
foo();
foo() will be called for each domain *not* in mask, if condition holds,
and not at all if condition doesn't hold.
Fix this by reversing the conditions in the macros, and adding an else
branch for the "for each" block, so that other if/else blocks can't
interfere. Provide a "for_each_if" helper macro to make it easier to get
this right.
v2: move for_each_if to drmP.h in a separate patch.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448392916-2281-2-git-send-email-jani.nikula@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we experience a refcounting failure in a power domain/well (unref'ing at
least one too many times), log the name of the offending domain or well.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448034934-11926-2-git-send-email-daniels@collabora.com
Let us print human-parseable values from the power domain code; upcoming
display code also wants to use it.
This requires moving it out of i915_debugfs.c, as that is only conditionally
compiled.
v2: Move it out of the header.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448034934-11926-1-git-send-email-daniels@collabora.com
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWUmHZAAoJEHm+PkMAQRiGHtcH/RVRsn8re0WdRWYaTr9+Hknm
CGlRJN4LKecttgYQ/2bS1QsDbt8usDPBiiYVopqGXQxPBmjyDAqPjsa+8VzCaVc6
WA+9LDB+PcW28lD6BO+qSZCOAm7hHSZq7dtw9x658IqO+mI2mVeCybsAyunw2iWi
Kf5q90wq6tIBXuT8YH9MXGrSCQw00NclbYeYwB9CmCt9hT/koEFBdl7uFUFitB+Q
GSPTz5fXhgc5Lms85n7flZlrVKoQKmtDQe4/DvKZm+SjsATHU9ru89OxDBdS5gSG
YcEIM4zc9tMjhs3GC9t6WXf6iFOdctum8HOhUoIN/+LVfeOMRRwAhRVqtGJ//Xw=
=DCUg
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rc2' into drm-intel-next-queued
Linux 4.4-rc2
Backmerge to get at
commit 1b0e3a049e
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Nov 5 23:04:11 2015 +0200
drm/i915/skl: disable display side power well support for now
so that we can proplery re-eanble skl power wells in -next.
Conflicts are just adjacent lines changed, except for intel_fbdev.c
where we need to interleave the changs. Nothing nefarious.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Handle DC off as a power well where enabling the power well will prevent
the DMC to enter selected DC states (required around modesets and Aux
A). Disabling the power well will allow DC states again. For now the
highest DC state is DC6 for Skylake and DC5 for Broxton but will be
configurable for Skylake in a later patch.
v2: Check both DC5 and DC6 bits in power well enabled function (Ville)
v3:
- Remove unneeded DC_OFF case in skl_set_power_well() (Imre)
- Add PW2 dependency to DC_OFF (Imre)
v4: Put DC_OFF before PW2 in BXT power well array
Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[fixed line over 80 and parenthesis alignment checkpatch warns (imre)]
Link: http://patchwork.freedesktop.org/patch/msgid/1447687201-24759-1-git-send-email-patrik.jakobsson@linux.intel.com
PG2 enabled is not a requirement for disabling DC5. It's just one
of the reasons why the DMC wouldn't enter DC5. During modeset we don't
care about PG2 from a DC perspective, only the fact that DC5/DC6 is not
allowed.
Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447084107-8521-9-git-send-email-patrik.jakobsson@linux.intel.com
All the DDI power domains are already excluded from
SKL_DISPLAY_ALWAYS_ON_POWER_DOMAINS on account of
excluding SKL_DISPLAY_POWERWELL_1_POWER_DOMAINS and
SKL_DISPLAY_POWERWELL_2_POWER_DOMAINS, no need to spell them out again.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447084107-8521-6-git-send-email-patrik.jakobsson@linux.intel.com
Currently the gmbus code uses intel_aux_display_runtime_get/put in an
effort to make sure the hardware is powered up sufficiently for gmbus.
That function only takes the runtime PM reference which on VLV/CHV/BXT
is not enough. We need the disp2d/pipe-a well on VLV/CHV and power well
2 on BXT. So add a new power domnain for gmbus and kill off the now
unused intel_aux_display_runtime_get/put. And change
intel_hdmi_set_edid() to use the gmbus power domain too since that's all
we need there.
Also toss in a BUILD_BUG_ON() to catch problems if we run out of
bits for power domains. We're already really close to the limit...
[Patrik: Add gmbus string to debugfs output]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447084107-8521-5-git-send-email-patrik.jakobsson@linux.intel.com
When this option is 0 (so the power well support is disabled) we are
supposed to enable all power wells once and don't disable them unless we
system suspend the device. Currently if the option is 0, we can call the
power well enable handlers multiple times, whenever their refcount
changes from 0->1. This may not be a problem for the HW, but it's not
logical and may trigger some warnings in the power well code which
doesn't expect this. So simply keep around a reference while we are
not system suspended to solve this. For simplicity mark the module
option read only, so we don't need to deal with re-enabling the feature
during runtime. If someone really needs that it could be added later in
a more proper way.
v2:
- fix typo in comment in intel_power_domains_suspend() (Patrik)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447775063-24438-1-git-send-email-imre.deak@intel.com
We don't need to reinit DDI and IRQs during PW1 enabling any more, since
we don't toggle PW1 on-demand any more. We enable PW1 only as part of
the display core init sequence and after this we initialize both DDI and
IRQs later in the init sequence. So remove these init steps from the
power well code.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-11-git-send-email-imre.deak@intel.com
We need to disable the DC states during display core init to sanitize
the HW state we inherit from the BIOS. We need to disable it during
display core uninit too, since the power well framework will leave it
enabled (since we get to the display core uninit step with all power
domains disabled already).
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-9-git-send-email-imre.deak@intel.com
Imre Deak