Trivial conflict in net/core/filter.c, a locally computed
'sdif' is now an argument to the function.
Signed-off-by: David S. Miller <davem@davemloft.net>
The response for a SNMP request can consist of multiple parts, which
the cmd callback stages into a kernel buffer until all parts have been
received. If the callback detects that the staging buffer provides
insufficient space, it bails out with error.
This processing is buggy for the first part of the response - while it
initially checks for a length of 'data_len', it later copies an
additional amount of 'offsetof(struct qeth_snmp_cmd, data)' bytes.
Fix the calculation of 'data_len' for the first part of the response.
This also nicely cleans up the memcpy code.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMC-D stress workload showed connection stalls. Since the firmware
decides to skip raising an interrupt if the SBA DMBE mask bit is
still set, this SBA DMBE mask bit should be cleared before the
IRQ handling in the SMC code runs. Otherwise there are small windows
possible with missing interrupts for incoming data.
SMC-D currently does not care about the old value of the SBA DMBE
mask.
Acked-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_l3_setup_netdev() checks if the hsuid attribute is set on the qeth
device, and propagates it to the net_device. In the past this was needed
to pick up any hsuid that was set before allocation of the net_device.
With commit d3d1b205e8 ("s390/qeth: allocate netdevice early") this
is no longer necessary, qeth_l3_dev_hsuid_store() always stores the
hsuid straight into dev->perm_addr.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the CREATE ADDR sent by qeth_l3_iqd_read_initial_mac() fails, its
callback sets a random MAC address on the net_device. The error then
propagates back, and qeth_l3_setup_netdev() bails out without
registering the net_device.
Any subsequent call to qeth_l3_setup_netdev() will then attempt a fresh
CREATE ADDR which either 1) also fails, or 2) sets a proper MAC address
on the net_device. Consequently, the net_device will never be registered
with a random MAC and we can drop the fallback code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_l3_send_ipa_arp_cmd() is merely a wrapper around
qeth_send_control_data() now. So push the length adjustment into
QETH_SETASS_BASE_LEN, and remove the wrapper. While at it, also remove
some redundant 0-initializations.
qeth_send_setassparms() requires that callers prepare their command
parameters, so that they can be copied into the parameter area in one
go. Skip the indirection, and just let callers set up the command
themselves.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call qeth_prepare_ipa_cmd() during setup of a new IPA cmd buffer, so
that it is used for all commands. Thus ARP and SNMP requests don't have
to do their own initialization.
This will now also set the proper MPC protocol version for SNMP requests
on L2 devices.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-implement the card-by-RDEV lookup by using device model concepts, and
remove the now redundant list of all qeth card instances in the system.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 82bf5c0867 ("s390/qeth: add support for IPv6 TSO"),
qeth_xmit() also knows how to build TSO packets and is practically
identical to qeth_l3_xmit().
Convert qeth_l3_xmit() into a thin wrapper that merely strips the
L2 header off a packet, and calls qeth_xmit() for the actual
TX processing.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filling the HW header from one single function will make it easier to
rip out all the duplicated transmit code in qeth_l3_xmit(). On top, this
saves one conditional branch in the TSO path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, READ MAC on a Layer2 OSD device returns the adapter's
burnt-in MAC address. Given the default scenario of many virtual devices
on the same adapter, qeth can't make any use of this address and
therefore skips the READ MAC call for this device type.
But in some configurations, the READ MAC command for a Layer2 OSD device
actually returns a pre-provisioned, virtual MAC address. So enable the
READ MAC code to detect this situation, and let the L2 subdriver
call READ MAC for OSD devices.
This also removes the QETH_LAYER2_MAC_READ flag, which protects L2
devices against calling READ MAC multiple times. Instead protect the
whole call to qeth_l2_request_initial_mac().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the various identifiers for 25Gbit cards, and wires them up
into sysfs and ethtool.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ARP_{ADD,REMOVE}_ENTRY cmd structs contain reserved fields.
Introduce a common helper that doesn't raw-copy the user-provided data
into the cmd, but only sets those fields that are strictly needed for
the command.
This also sets the correct command length for ARP_REMOVE_ENTRY.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting the carrier 'on' for an unregistered netdevice doesn't update
its operstate. Fix this by delaying the update until the netdevice has
been registered.
Fixes: 91cc98f51e ("s390/qeth: remove duplicated carrier state tracking")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth only registers its netdevice when the qeth device is first set
online. Thus a device that has never been set online will trigger
a WARN ("network todo 'hsi%d' but state 0") in unregister_netdev() when
removed.
Fix this by protecting the unregister step, just like we already protect
against repeated registering of the netdevice.
Fixes: d3d1b205e8 ("s390/qeth: allocate netdevice early")
Reported-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sniffing mode for L3 HiperSockets requires that no IP addresses are
registered with the HW. The preferred way to achieve this is for
userspace to delete all the IPs on the interface. But qeth is expected
to also tolerate a configuration where that is not the case, by skipping
the IP registration when in sniffer mode.
Since commit 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
reworked the IP registration logic in the L3 subdriver, this no longer
works. When the qeth device is set online, qeth_l3_recover_ip() now
unconditionally registers all unicast addresses from our internal
IP table.
While we could fix this particular problem by skipping
qeth_l3_recover_ip() on a sniffer device, the more future-proof change
is to skip the IP address registration at the lowest level. This way we
a) catch any future code path that attempts to register an IP address
without considering the sniffer scenario, and
b) continue to build up our internal IP table, so that if sniffer mode
is switched off later we can operate just like normal.
Fixes: 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Documentation/s390/s390dbf.txt states quite clearly, using any
pointer in sprinf-formatted s390dbf debug entries is dangerous.
The pointers are dereferenced whenever the trace file is read from.
So if the referenced data has a shorter life-time than the trace file,
any read operation can result in a use-after-free.
So rip out all hazardous use of indirect data, and replace any usage of
dev_name() and such by the Bus ID number.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=58I4
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Fix ASPM link_state teardown on removal (Lukas Wunner)
- Fix misleading _OSC ASPM message (Sinan Kaya)
- Make _OSC optional for PCI (Sinan Kaya)
- Don't initialize ASPM link state when ACPI_FADT_NO_ASPM is set
(Patrick Talbert)
- Remove x86 and arm64 node-local allocation for host bridge structures
(Punit Agrawal)
- Pay attention to device-specific _PXM node values (Jonathan Cameron)
- Support new Immediate Readiness bit (Felipe Balbi)
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state
(Keith Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and
re-enumerate devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets
(Keith Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable
from cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments
(Keith Busch)
- Remove unused Netronome NFP32xx Device IDs (Jakub Kicinski)
- Use bitmap_zalloc() for dma_alias_mask (Andy Shevchenko)
- Add switch fall-through annotations (Gustavo A. R. Silva)
- Remove unused Switchtec quirk variable (Joshua Abraham)
- Fix pci.c kernel-doc warning (Randy Dunlap)
- Remove trivial PCI wrappers for DMA APIs (Christoph Hellwig)
- Add Intel GPU device IDs to spurious interrupt quirk (Bin Meng)
- Run Switchtec DMA aliasing quirk only on NTB endpoints to avoid
useless dmesg errors (Logan Gunthorpe)
- Update Switchtec NTB documentation (Wesley Yung)
- Remove redundant "default n" from Kconfig (Bartlomiej Zolnierkiewicz)
- Avoid panic when drivers enable MSI/MSI-X twice (Tonghao Zhang)
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
- Fix VMD AERSID quirk Device ID matching (Jon Derrick)
- Fix Cadence PHY handling during probe (Alan Douglas)
- Signal Cadence Endpoint interrupts via AXI region 0 instead of last
region (Alan Douglas)
- Write Cadence Endpoint MSI interrupts with 32 bits of data (Alan
Douglas)
- Remove redundant controller tests for "device_type == pci" (Rob
Herring)
- Document R-Car E3 (R8A77990) bindings (Tho Vu)
- Add device tree support for R-Car r8a7744 (Biju Das)
- Drop unused mvebu PCIe capability code (Thomas Petazzoni)
- Add shared PCI bridge emulation code (Thomas Petazzoni)
- Convert mvebu to use shared PCI bridge emulation (Thomas Petazzoni)
- Add aardvark Root Port emulation (Thomas Petazzoni)
- Support 100MHz/200MHz refclocks for i.MX6 (Lucas Stach)
- Add initial power management for i.MX7 (Leonard Crestez)
- Add PME_Turn_Off support for i.MX7 (Leonard Crestez)
- Fix qcom runtime power management error handling (Bjorn Andersson)
- Update TI dra7xx unaligned access errata workaround for host mode as
well as endpoint mode (Vignesh R)
- Fix kirin section mismatch warning (Nathan Chancellor)
- Remove iproc PAXC slot check to allow VF support (Jitendra Bhivare)
- Quirk Keystone K2G to limit MRRS to 256 (Kishon Vijay Abraham I)
- Update Keystone to use MRRS quirk for host bridge instead of open
coding (Kishon Vijay Abraham I)
- Refactor Keystone link establishment (Kishon Vijay Abraham I)
- Simplify and speed up Keystone link training (Kishon Vijay Abraham I)
- Remove unused Keystone host_init argument (Kishon Vijay Abraham I)
- Merge Keystone driver files into one (Kishon Vijay Abraham I)
- Remove redundant Keystone platform_set_drvdata() (Kishon Vijay
Abraham I)
- Rename Keystone functions for uniformity (Kishon Vijay Abraham I)
- Add Keystone device control module DT binding (Kishon Vijay Abraham
I)
- Use SYSCON API to get Keystone control module device IDs (Kishon
Vijay Abraham I)
- Clean up Keystone PHY handling (Kishon Vijay Abraham I)
- Use runtime PM APIs to enable Keystone clock (Kishon Vijay Abraham I)
- Clean up Keystone config space access checks (Kishon Vijay Abraham I)
- Get Keystone outbound window count from DT (Kishon Vijay Abraham I)
- Clean up Keystone outbound window configuration (Kishon Vijay Abraham
I)
- Clean up Keystone DBI setup (Kishon Vijay Abraham I)
- Clean up Keystone ks_pcie_link_up() (Kishon Vijay Abraham I)
- Fix Keystone IRQ status checking (Kishon Vijay Abraham I)
- Add debug messages for all Keystone errors (Kishon Vijay Abraham I)
- Clean up Keystone includes and macros (Kishon Vijay Abraham I)
- Fix Mediatek unchecked return value from devm_pci_remap_iospace()
(Gustavo A. R. Silva)
- Fix Mediatek endpoint/port matching logic (Honghui Zhang)
- Change Mediatek Root Port Class Code to PCI_CLASS_BRIDGE_PCI (Honghui
Zhang)
- Remove redundant Mediatek PM domain check (Honghui Zhang)
- Convert Mediatek to pci_host_probe() (Honghui Zhang)
- Fix Mediatek MSI enablement (Honghui Zhang)
- Add Mediatek system PM support for MT2712 and MT7622 (Honghui Zhang)
- Add Mediatek loadable module support (Honghui Zhang)
- Detach VMD resources after stopping root bus to prevent orphan
resources (Jon Derrick)
- Convert pcitest build process to that used by other tools (iio, perf,
etc) (Gustavo Pimentel)
* tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI: pcie: Remove redundant 'default n' from Kconfig
PCI: aardvark: Implement emulated root PCI bridge config space
PCI: mvebu: Convert to PCI emulated bridge config space
PCI: mvebu: Drop unused PCI express capability code
PCI: Introduce PCI bridge emulated config space common logic
PCI: vmd: Detach resources after stopping root bus
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
...
Except for the new HW header id, this works just like TSO6 on L3 devices
and reuses all the existing data path support in qeth_xmit().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds TSO6 support for L3 qeth devices.
Just like for standard IPv6 traffic, TSO6 doesn't use IP offload and
thus runs over the normal qeth_xmit() path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TSO6 requires the full programming sequence, and not just a simple
START command. This implements the additional ENABLE command, and adds
some sanity checks that were missing for the START command.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for IPv6 TSO, turn the protocol version into a parameter
for the TSO control code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The few callers can just use dma_set_max_seg_size ()directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The two callers can just use dma_set_seg_boundary() directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions qeth_get_ipa_msg and qeth_get_ipa_cmd_name are modifying
the last member of global arrays without any locking that I can see.
If two instances of either function are running at the same time,
it could cause a race ultimately leading to an array overrun (the
contents of the last entry of the array is the only guarantee that
the loop will ever stop).
Performing the lookups without modifying the arrays is admittedly
slower (two comparisons per iteration instead of one) but these
are operations which are rare (should only be needed in error
cases or when debugging, not during successful operation) and it
seems still less costly than introducing a mutex to protect the
arrays in question.
As a side bonus, it allows us to declare both arrays as const data.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Julian Wiedmann <jwi@linux.ibm.com>
Cc: Ursula Braun <ubraun@linux.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the common code ARRAY_SIZE macro instead of a private implementation.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdevice is always available, apply any carrier state changes to it
without caching them.
On a STARTLAN event (ie. carrier-up), defer updating the state to
qeth_core_hardsetup_card() in the subsequent recovery action.
Also remove the carrier-state checks from the xmit routines. Stopping
transmission on carrier-down is the responsibility of upper-level code
(eg see dev_direct_xmit()).
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If qeth_check_ipa_data() consumed an event, there's no point in
processing it further. So drop it early, and make the surrounding code
a tiny bit more readable.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull one level of checking up into qeth_send_control_data_cb(), and
clean up an else-after-return. No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have no code that is waiting for these events, so just drop them when
they arrive.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. tracing iob->rc makes no sense when it hasn't been modified by the
callback,
2. the qeth_dbf_list is declared with LIST_HEAD, which also initializes
the list,
3. the ccwgroup core only calls the thaw/restore callbacks if the gdev
is online, so we don't have to check for it again.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cdev-to-card translation walks through two layers of drvdata,
with no locking or refcounting (where eg. the ccwgroup core only
accesses a cdev's drvdata while holding the ccwlock).
This might be safe for now, but any careless usage of the helper has the
potential for subtle races and use-after-free's. Luckily there's only
one occurrence where we _really_ need it (in qeth_irq()), for any other
user we can just pass through an appropriate card pointer.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows us to remove the CARD_FROM_CDEV calls in the iob callbacks.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When not using the CQ, this allows us avoid the second skb queue walk
in qeth_release_skbs().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was presumably left over from back when qeth recursed into
dev_queue_xmit().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To match the use of __skb_queue_purge(), also make the skb's enqueue in
qeth_fill_buffer() lockless.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch attempts to untangle the TX and RX code in qeth from
af_iucv's respective HiperTransport path:
On the TX side, pointing skb_network_header() at the IUCV header
means that qeth_l3_fill_af_iucv_hdr() no longer needs a magical offset
to access the header.
On the RX side, qeth pulls the (fake) L2 header off the skb like any
normal ethernet driver would. This makes working with the IUCV header
in af_iucv easier, since we no longer have to assume a fixed skb layout.
While at it, replace the open-coded length checks in af_iucv's RX path
with pskb_may_pull().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_core_probe_device() sets the gdev's drvdata, but doesn't reset it
on a subsequent error. Move the (re-)setting around a bit, so that it
happens symmetrically on allocating/freeing the qeth_card struct.
This is no actual problem, as the ccwgroup core will discard the gdev
on a probe error. But from qeth's perspective the gdev is an external
resource, so it's best to manage it cleanly.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device initialization code usually first loads a subdriver
(via qeth_core_load_discipline()), and then runs its setup() callback.
If this fails, it rolls back the load via qeth_core_free_discipline().
qeth_core_free_discipline() expects the options.layer attribute to be
initialized, but on error in setup() that's currently not the case.
Resulting in misbalanced symbol_put() calls.
Fix this by setting options.layer when loading the subdriver.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate declaration and initialization of a static variable.
While at it reduce its scope in qeth_core_load_discipline(), and simplify
the return logic accordingly.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the raw values are fixed due to their use in a sysfs attribute,
we can still use the proper QETH_DISCIPLINE_* enum within the driver.
Also move the initialization into qeth_set_initial_options(), along with
all other user-configurable fields.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_get_ipacmd_buffer() obtains its buffers for building IPA cmds from
__qeth_get_buffer(), where they are fully cleared. So get rid of all the
additional zero-ing in various other places.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For quite a lot of code paths it's obvious that they will never run in
IRQ context. So replace their spin_lock_irqsave() calls with
spin_lock_irq().
While at it, get rid of the redundant card pointer in struct qeth_reply
that was used by qeth_send_control_data() to access the card's lock.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assuming this was just a typo, as returning an actual negative value
from a cmd callback would make no sense either.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling napi_schedule() from process context does not ensure that the
NET_RX softirq is run in a timely fashion. So trigger it manually.
This is no big issue with current code. A call to ndo_open() is usually
followed by a ndo_set_rx_mode() call, and for qeth this contains a
spin_unlock_bh(). Except for OSN, where qeth_l2_set_rx_mode() bails out
early.
Nevertheless it's best to not depend on this behaviour, and just fix
the issue at its source like all other drivers do. For instance see
commit 83a0c6e589 ("i40e: Invoke softirqs after napi_reschedule").
Fixes: a1c3ed4c9c ("qeth: NAPI support for l2 and l3 discipline")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting up, qeth installs its IRQ handler on the ccw devices. But
the IRQ handler is not cleared on removal - so even after qeth yields
control of the ccw devices, spurious interrupts would still be presented
to us.
Make (de-)installation of the IRQ handler part of the ccw channel
setup/removal helpers, and while at it also add the appropriate locking.
Shift around qeth_setup_channel() to avoid a forward declaration for
qeth_irq().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restructure the OSN xmit path to handle misaligned HW headers properly,
without shifting the packet data around.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch TSO over to the faster transmit path, and remove all the unused
old TSO code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add all the necessary TSO plumbing to the copy-less transmit path.
This includes calculating the right length of required protocol headers,
and always building a separate buffer element for the TSO headers.
A follow-up patch will then switch TSO traffic over to this path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When qeth_add_hw_header() falls back to the header cache, ensure that
the requested length doesn't exceed the object size.
For current usage this is a no-brainer, but TSO transmission will
introduce protocol headers of varying length.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When qeth_add_hw_header() falls back to the HW header cache, it also
copies over the necessary protocol headers. Thus any manipulation to
the protocol headers needs to happen before adding the HW header.
For current usage this doesn't matter, but it becomes relevant when
moving TSO transmission over to the faster code path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Combined L3+L4 csum offload is only required for some L3 HW. So for
L2 devices, don't offload the IP header csum calculation.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reference-ID: JUP 394553
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the last remaining user of qeth_get_elements_no() to
qeth_count_elements(), so this helper can be removed.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_l3_xmit() is now only used for TSOv4 traffic, shrink it down.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L3 OSAs can only offload IPv4 traffic, use the common L2 transmit path
for all other traffic.
In particular there's no support for TX VLAN offload, so any such packet
needs to be manually de-accelerated via ndo_features_check().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need the exact same transmit path for non-offload-eligible traffic on
L3 OSAs. So make it accessible from both sub-drivers.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For inbound data with an unsupported HW header format, only dump the
actual HW header. We have no idea how much payload follows it, and what
it contains. Worst case, we dump past the end of the Inbound Buffer and
access whatever is located next in memory.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_query_oat_command() currently allocates the kernel buffer for
the SIOC_QETH_QUERY_OAT ioctl with kzalloc. So on systems with
fragmented memory, large allocations may fail (eg. the qethqoat tool by
default uses 132KB).
Solve this issue by using vzalloc, backing the allocation with
non-contiguous memory.
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scatter-gather transmit brings a nice performance boost. Considering the
rather large MTU sizes at play, it's also totally the Right Thing To Do.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bailing out on allocation error is nice, but we also need to tell the
ccwgroup core that creating the qeth groupdev failed.
Fixes: d3d1b205e8 ("s390/qeth: allocate netdevice early")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return statements in functions returning bool should use true or false
instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocating the main qeth_card struct with GFP_DMA blocks us from moving
it into netdev_priv(). But the only reason why we need DMA memory is the
ccw1 structs embedded into each ccw channel. So extract those into
separate allocations, like we already do for the cmd buffers.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qeth_card struct is kzalloc-ed, so remove all the redundant
0-initializations. While at it, split up what's left of
qeth_determine_card_type().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data channel currently doesn't need a setup operation, because we
don't use pre-allocated cmd buffers for its IO. But subsequent changes
will introduce further setup that also applies to the data channel.
This refactors things a bit, so that the new stuff can then be
automatically applied to all channels.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-work the helper a little bit, so that it can be used for all CCWs
that qeth issues.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Where possible use accessor macros and local pointers to access the ccw
channels. This makes it less likely to miss a spot.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the L2 OSA xmit path so that it also supports L2 IQD devices
(in particular, their HW header requirements). This allows IQD devices
to advertise NETIF_F_SG support, and eliminates the allocation overhead
for the HW header.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some transmit modes require that the HW header is located in the same
page as the initial protocol headers in skb->data. Let callers specify
the size of this contiguous header range, and enforce it when building
the HW header.
While at it, apply some gentle renaming to the relevant L2 code so that
it matches the L3 code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking whether an skb needs to be linearized to fit into an IO
buffer, it's desirable to consider the skb's final size and layout
(ie. after the HW header was added). But a subsequent linearization can
then cause the re-positioned HW header to violate its alignment
restrictions.
Dealing with this situation in two different code paths is quite tricky.
This patch integrates a) linearize-check and b) HW header construction
into one 3 step-sequence:
1. evaluate how the HW header needs to be added (to identify if it takes
up an additional buffer element), then
2. check if the required buffer elements exceed the device's limit.
Linearize when necessary and re-evaluate the HW header placement.
3. Add the HW header in the best-possible way:
a) push, without taking up an additional buffer element
b) push, but consume another buffer element
c) allocate a header object from the cache.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nowadays an skb fragment typically spans over multiple pages. So replace
the obsolete, SG-only 'fragments' counter with one that tracks the
consumed buffer elements. This is what actually matters for performance.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth's ndo_change_mtu() only applies some trivial bounds checking. Set
up dev->min_mtu properly, so that dev_set_mtu() can do this for us.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the MPC initialization code discovers the HW-specific max MTU,
apply the resulting changes straight to the netdevice.
If this is the device's first initialization, also set its MTU
(HiperSockets: the max MTU; else: a layer-specific default value).
Then cap the current MTU by the new max MTU.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdevice is always available now, so get the portno from there.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocation of the netdevice is currently delayed until a qeth card first
goes online. This complicates matters in several places, where we need
to cache values instead of applying them straight to the netdevice.
Improve on this by moving the allocation up to where the qeth card
itself is created. This is also one step in direction of eventually
placing the qeth card into netdev_priv().
In all subsequent code, remove the now redundant checks whether
card->dev is valid.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the subdriver's remove() routine has completed, the card's layer
mode is undetermined again. Reflect this in the layer2 field.
If qeth_dev_layer2_store() hits an error after remove() was called, the
card _always_ requires a setup(), even if the previous layer mode is
requested again.
But qeth_dev_layer2_store() bails out early if the requested layer mode
still matches the current one. So unless we reset the layer2 field,
re-probing the card back to its previous mode is currently not possible.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By updating q->used_buffers only _after_ do_QDIO() has completed, there
is a potential race against the buffer's TX completion. In the unlikely
case that the TX completion path wins, qeth_qdio_output_handler() would
decrement the counter before qeth_flush_buffers() even incremented it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the xmit of offload-eligible (ie IPv4) traffic on OSA over to the
new, copy-free path.
As with L2, we'll need to preserve the skb_orphan() behaviour of the
old code path until TX completion is sufficiently fast.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements a new xmit path for L3 HiperSockets, which carves the
HW header from skb headroom instead of allocating it from the hdr cache.
It also adds NETIF_F_SG support.
The delta in qeth_l3_xmit() is all just removal of IQD-specific code and
some minor consolidation.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for future work, move the high-level xmit work into a
separate wrapper. This matches the L2 xmit code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a L3 device doesn't offer TSO, allow the stack to build full-size
GSO skbs.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some redundant EXPORTs. While at it, also move some L2-only
prototypes into the proper header file.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reshuffle the code a bit so that everything is in one place.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate duplicated code, fix the misuse of RTN_UNSPEC and simplify
the handling of non-unicast traffic on IQD devices.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing a device's address lists (or its promisc mode) already triggers
an RX modeset, there's no need to do it manually from the L2 driver's
ndo_vlan_rx_kill_vid() hook.
Also when setting a device online, dev_open() already calls
dev_set_rx_mode(). So a manual modeset is only necessary from the
recovery path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Except for tracing, the pointer is not used.
At the same time, accessing it from qeth_qdio_output_handler() is racy:
whenever qeth_qdio_cq_handler() gets control, its call to
qeth_qdio_handle_aob() frees the AOB.
So the AOB pointer that qeth_qdio_output_handler() stores into 'buffer'
can go stale at any time, and trigger a use-after-free.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new qeth_scrub_qdio_buffer() helper, remove an extra parameter
from qeth_clear_output_buffer(), init the bufstates.user field just once
(in qeth_flush_buffers()) and remove some noisy trace messages.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple overlapping changes in stmmac driver.
Adjust skb_gro_flush_final_remcsum function signature to make GRO list
changes in net-next, as per Stephen Rothwell's example merge
resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
commit e830baa9c3 ("qeth: restore device features after recovery") and
commit ce34435641 ("s390/qeth: rely on kernel for feature recovery")
made sure that the HW functions for device features get re-programmed
after recovery.
But we missed that the same handling is also required when a card is
first set offline (destroying all HW context), and then online again.
Fix this by moving the re-enable action out of the recovery-only path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If qeth_qdio_output_handler() detects that a transmit requires async
completion, it replaces the pending buffer's metadata object
(qeth_qdio_out_buffer) so that this queue buffer can be re-used while
the data is pending completion.
Later when the CQ indicates async completion of such a metadata object,
qeth_qdio_cq_handler() tries to free any data associated with this
object (since HW has now completed the transfer). By calling
qeth_clear_output_buffer(), it erronously operates on the queue buffer
that _previously_ belonged to this transfer ... but which has been
potentially re-used several times by now.
This results in double-free's of the buffer's data, and failing
transmits as the buffer descriptor is scrubbed in mid-air.
The correct way of handling this situation is to
1. scrub the queue buffer when it is prepared for re-use, and
2. later obtain the data addresses from the async-completion notifier
(ie. the AOB), instead of the queue buffer.
All this only affects qeth devices used for af_iucv HiperTransport.
Fixes: 0da9581ddb ("qeth: exploit asynchronous delivery of storage blocks")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
*ether_addr*_64bits functions have been introduced to optimize
performance critical paths, which access 6-byte ethernet address as u64
value to get "nice" assembly. A harmless hack works nicely on ethernet
addresses shoved into a structure or a larger buffer, until busted by
Kasan on smth like plain (u8 *)[6].
qeth_l2_set_mac_address calls qeth_l2_remove_mac passing
u8 old_addr[ETH_ALEN] as an argument.
Adding/removing macs for an ethernet adapter is not that performance
critical. Moreover is_multicast_ether_addr_64bits itself on s390 is not
faster than is_multicast_ether_addr:
is_multicast_ether_addr(%r2) -> %r2
llc %r2,0(%r2)
risbg %r2,%r2,63,191,0
is_multicast_ether_addr_64bits(%r2) -> %r2
llgc %r2,0(%r2)
risbg %r2,%r2,63,191,0
So, let's just use is_multicast_ether_addr instead of
is_multicast_ether_addr_64bits.
Fixes: bcacfcbc82 ("s390/qeth: fix MAC address update sequence")
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When qeth_l2_set_mac_address() finds the card in a non-reachable state,
it merely copies the new MAC address into dev->dev_addr so that
__qeth_l2_set_online() can later register it with the HW.
But __qeth_l2_set_online() may very well be running concurrently, so we
can't trust the card state without appropriate locking:
If the online sequence is past the point where it registers
dev->dev_addr (but not yet in SOFTSETUP state), any address change needs
to be properly programmed into the HW. Otherwise the netdevice ends up
with a different MAC address than what's set in the HW, and inbound
traffic is not forwarded as expected.
This is most likely to occur for OSD in LPAR, where
commit 21b1702af1 ("s390/qeth: improve fallback to random MAC address")
now triggers eg. systemd to immediately change the MAC when the netdevice
is registered with a NET_ADDR_RANDOM address.
Fixes: bcacfcbc82 ("s390/qeth: fix MAC address update sequence")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit b7493e91c1.
On its own, querying RDEV for a MAC address works fine. But when upgrading
from a qeth that previously queried DDEV on a z/VM NIC (ie. any kernel with
commit ec61bd2fd2), the RDEV query now returns a _different_ MAC address
than the DDEV query.
If the NIC is configured with MACPROTECT, z/VM apparently requires us to
use the MAC that was initially returned (on DDEV) and registered. So after
upgrading to a kernel that uses RDEV, the SETVMAC registration cmd for the
new MAC address fails and we end up with a non-operabel interface.
To avoid regressions on upgrade, switch back to using DDEV for the MAC
address query. The downgrade path (first RDEV, later DDEV) is fine, in this
case both queries return the same MAC address.
Fixes: b7493e91c1 ("s390/qeth: use Read device to query hypervisor for MAC")
Reported-by: Michal Kubecek <mkubecek@suse.com>
Tested-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Internal Shared Memory vPCI Adapter.
This driver implements the interfaces of the SMC-D protocol.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add Maglev hashing scheduler to IPVS, from Inju Song.
2) Lots of new TC subsystem tests from Roman Mashak.
3) Add TCP zero copy receive and fix delayed acks and autotuning with
SO_RCVLOWAT, from Eric Dumazet.
4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard
Brouer.
5) Add ttl inherit support to vxlan, from Hangbin Liu.
6) Properly separate ipv6 routes into their logically independant
components. fib6_info for the routing table, and fib6_nh for sets of
nexthops, which thus can be shared. From David Ahern.
7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP
messages from XDP programs. From Nikita V. Shirokov.
8) Lots of long overdue cleanups to the r8169 driver, from Heiner
Kallweit.
9) Add BTF ("BPF Type Format"), from Martin KaFai Lau.
10) Add traffic condition monitoring to iwlwifi, from Luca Coelho.
11) Plumb extack down into fib_rules, from Roopa Prabhu.
12) Add Flower classifier offload support to igb, from Vinicius Costa
Gomes.
13) Add UDP GSO support, from Willem de Bruijn.
14) Add documentation for eBPF helpers, from Quentin Monnet.
15) Add TLS tx offload to mlx5, from Ilya Lesokhin.
16) Allow applications to be given the number of bytes available to read
on a socket via a control message returned from recvmsg(), from
Soheil Hassas Yeganeh.
17) Add x86_32 eBPF JIT compiler, from Wang YanQing.
18) Add AF_XDP sockets, with zerocopy support infrastructure as well.
From Björn Töpel.
19) Remove indirect load support from all of the BPF JITs and handle
these operations in the verifier by translating them into native BPF
instead. From Daniel Borkmann.
20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha.
21) Allow XDP programs to do lookups in the main kernel routing tables
for forwarding. From David Ahern.
22) Allow drivers to store hardware state into an ELF section of kernel
dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy.
23) Various RACK and loss detection improvements in TCP, from Yuchung
Cheng.
24) Add TCP SACK compression, from Eric Dumazet.
25) Add User Mode Helper support and basic bpfilter infrastructure, from
Alexei Starovoitov.
26) Support ports and protocol values in RTM_GETROUTE, from Roopa
Prabhu.
27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard
Brouer.
28) Add lots of forwarding selftests, from Petr Machata.
29) Add generic network device failover driver, from Sridhar Samudrala.
* ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits)
strparser: Add __strp_unpause and use it in ktls.
rxrpc: Fix terminal retransmission connection ID to include the channel
net: hns3: Optimize PF CMDQ interrupt switching process
net: hns3: Fix for VF mailbox receiving unknown message
net: hns3: Fix for VF mailbox cannot receiving PF response
bnx2x: use the right constant
Revert "net: sched: cls: Fix offloading when ingress dev is vxlan"
net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
enic: fix UDP rss bits
netdev-FAQ: clarify DaveM's position for stable backports
rtnetlink: validate attributes in do_setlink()
mlxsw: Add extack messages for port_{un, }split failures
netdevsim: Add extack error message for devlink reload
devlink: Add extack to reload and port_{un, }split operations
net: metrics: add proper netlink validation
ipmr: fix error path when ipmr_new_table fails
ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
net: hns3: remove unused hclgevf_cfg_func_mta_filter
netfilter: provide udp*_lib_lookup for nf_tproxy
qed*: Utilize FW 8.37.2.0
...
If READ MAC fails to fetch a valid MAC address, allow some more device
types (IQD and z/VM OSD) to fall back to a random address.
Also use eth_hw_addr_random(), for indicating to userspace that the
address type is NET_ADDR_RANDOM.
Note that while z/VM has various protection schemes to prohibit
custom addresses on its NICs, they are all optional. So we should at
least give it a try.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check if a qeth device supports IPv6 RX checksum offload, and hook it up
into the existing NETIF_F_RXCSUM support.
As NETIF_F_RXCSUM is now backed by a combination of HW Assists, we need
to be a little smarter when dealing with errors during a configuration
change:
- switching on NETIF_F_RXCSUM only makes sense if at least one HW Assist
was enabled successfully.
- for switching off NETIF_F_RXCSUM, all available HW Assists need to be
deactivated.
Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check if a qeth device supports IPv6 TX checksum offload, and advertise
NETIF_F_IPV6_CSUM accordingly. Add support for setting the relevant bits
in IPv6 packet descriptors.
Currently this has only limited use (ie. UDP, or Jumbo Frames). For any
TCP traffic with a standard MSS, the TCP checksum gets calculated
as part of the linear GSO segmentation.
Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some wrappers to make the protocol-specific Assist code a little
more generic, and use them for sending protocol-agnostic commands in
the Checksum Offload Assist code.
Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For new functionality, the L2 subdriver will start using IPv6 assists.
So move the query from the L3 subdriver into the common setup path.
Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This matches the statistics we gather for the TX offload path.
Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel does its own validation of the IPv4 header checksum,
drivers/HW are not required to handle this.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This consolidates the checksum offload code that was duplicated
over the two qeth subdrivers.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial cleanup, in preparation for a subsequent patch.
Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct net_device contains a dev_port field. Store the OSA port number
in this field.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a VLAN ID on a L3 device, the driver currently attempts to
walk and unregister the VLAN device's IP addresses.
This can be safely removed - before qeth_l3_vlan_rx_kill_vid() even gets
called, we receive an inet[6]addr event for each IP on the device and
qeth_l3_handle_ip_event() unregisters the address accordingly.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the vid_list is only accessed from process context, there's no need to
protect it with a spinlock.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both qeth sub drivers use the same QDIO queue handlers, there's no need
to expose them via the driver's discipline. No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For z/VM NICs, qeth needs to consider which of the three CCW devices in
an MPC group it uses for requesting a managed MAC address.
On the Base device, the hypervisor returns a default MAC which is
pre-assigned when creating the NIC (this MAC is also returned by the
READ MAC primitive). Querying any other device results in the allocation
of an additional MAC address.
For consistency with READ MAC and to avoid using up more addresses than
necessary, it is preferable to use the NIC's default MAC. So switch the
the diag26c over to using a NIC's Read device, which should always be
identical to the Base device.
Fixes: ec61bd2fd2 ("s390/qeth: use diag26c to get MAC address on L2")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Submitting a cmd IO request (usually on the WRITE device, but for IDX
also on the READ device) is currently done with ccw_device_start()
and a manual timeout in the caller.
On timeout, the caller cleans up the related resources (eg. IO buffer).
But 1) the IO might still be active and utilize those resources, and
2) when the IO completes, qeth_irq() will attempt to clean up the
same resources again.
Instead of introducing additional resource locking, switch to
ccw_device_start_timeout() to ensure IO termination after timeout, and
let the IRQ handler alone deal with cleaning up after a request.
This also removes a stray write->irq_pending reset from
clear_ipacmd_list(). The routine doesn't terminate any pending IO on
the WRITE device, so this should be handled properly via IO timeout
in the IRQ handler.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing the MAC address on a L2 qeth device, current code first
unregisters the old address, then registers the new one.
If HW rejects the new address (or the IO fails), the device ends up with
no operable address at all.
Re-order the code flow so that the old address only gets dropped if the
new address was registered successfully. While at it, add logic to catch
some corner-cases.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Creating the global workqueue during driver init may fail, deal with it.
Also, destroy the created workqueue on any subsequent error.
Fixes: 0f54761d16 ("qeth: Support VEPA mode")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For control IO, qeth currently tracks the index of the buffer that it
expects to complete the next IO on each qeth_channel. If the channel
presents an IRQ while this buffer has not yet completed, no completion
processing for _any_ completed buffer takes place.
So if the 'next buffer' is skipped for any sort of reason* (eg. when it
is released due to error conditions, before the IO is started), the
buffer obviously won't switch to PROCESSED until it is eventually
allocated for a _different_ IO and completes.
Until this happens, all completion processing on that channel stalls
and pending requests possibly time out.
As a fix, remove the whole 'next buffer' logic and simply process any
IO buffer right when it completes. A channel will never have more than
one IO pending, so there's no risk of processing out-of-sequence.
*Note: currently just one location in the code really handles this problem,
by advancing the 'next' index manually.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to check both return code fields before(!) processing the
command response. Otherwise we risk operating on invalid data.
This matches an earlier fix for SETASSPARMS commands, see
commit ad3cbf6133 ("s390/qeth: fix error handling in checksum cmd callback").
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing couple of duplicate includes, found by "make includecheck".
That leaves 1 duplicate include in arch/s390/kernel/entry.S, which is
there for a reason (it includes generated asm/syscall_table.h twice).
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The module exit function of the smsgiucv module uses the incorrect CP
command to disable SMSG messages. The correct command is "SET SMSG OFF".
Use it.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull s390 updates from Martin Schwidefsky:
- Improvements for the spectre defense:
* The spectre related code is consolidated to a single file
nospec-branch.c
* Automatic enable/disable for the spectre v2 defenses (expoline vs.
nobp)
* Syslog messages for specve v2 are added
* Enable CONFIG_GENERIC_CPU_VULNERABILITIES and define the attribute
functions for spectre v1 and v2
- Add helper macros for assembler alternatives and use them to shorten
the code in entry.S.
- Add support for persistent configuration data via the SCLP Store Data
interface. The H/W interface requires a page table that uses 4K pages
only, the code to setup such an address space is added as well.
- Enable virtio GPU emulation in QEMU. To do this the depends
statements for a few common Kconfig options are modified.
- Add support for format-3 channel path descriptors and add a binary
sysfs interface to export the associated utility strings.
- Add a sysfs attribute to control the IFCC handling in case of
constant channel errors.
- The vfio-ccw changes from Cornelia.
- Bug fixes and cleanups.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (40 commits)
s390/kvm: improve stack frame constants in entry.S
s390/lpp: use assembler alternatives for the LPP instruction
s390/entry.S: use assembler alternatives
s390: add assembler macros for CPU alternatives
s390: add sysfs attributes for spectre
s390: report spectre mitigation via syslog
s390: add automatic detection of the spectre defense
s390: move nobp parameter functions to nospec-branch.c
s390/cio: add util_string sysfs attribute
s390/chsc: query utility strings via fmt3 channel path descriptor
s390/cio: rename struct channel_path_desc
s390/cio: fix unbind of io_subchannel_driver
s390/qdio: split up CCQ handling for EQBS / SQBS
s390/qdio: don't retry EQBS after CCQ 96
s390/qdio: restrict buffer merging to eligible devices
s390/qdio: don't merge ERROR output buffers
s390/qdio: simplify math in get_*_buffer_frontier()
s390/decompressor: trim uncompressed image head during the build
s390/crypto: Fix kernel crash on aes_s390 module remove.
s390/defkeymap: fix global init to zero
...
Rename struct channel_path_desc to struct channel_path_desc_fmt0
to fit the scheme. Provide a macro for the function wrappers that
gather this and related data from firmware.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the IRQ handler determines that one of the cmd IO channels has
failed and schedules recovery, block any further cmd requests from
being submitted. The request would inevitably stall, and prevent the
recovery from making progress until the request times out.
This sort of error was observed after Live Guest Relocation, where
the pending IO on the READ channel intentionally gets terminated to
kick-start recovery. Simultaneously the guest executed SIOCETHTOOL,
triggering qeth to issue a QUERY CARD INFO command. The command
then stalled in the inoperabel WRITE channel.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For calling ccw_device_start(), issue_next_read() needs to hold the
device's ccwlock.
This is satisfied for the IRQ handler path (where qeth_irq() gets called
under the ccwlock), but we need explicit locking for the initial call by
the MPC initialization.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_wait_for_threads() is potentially called by multiple users, make
sure to notify all of them after qeth_clear_thread_running_bit()
adjusted the thread_running_mask. With no timeout, callers would
otherwise stall.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On removal, a qeth card's netdevice is currently not properly freed
because the call chain looks as follows:
qeth_core_remove_device(card)
lx_remove_device(card)
unregister_netdev(card->dev)
card->dev = NULL !!!
qeth_core_free_card(card)
if (card->dev) !!!
free_netdev(card->dev)
Fix it by free'ing the netdev straight after unregistering. This also
fixes the sysfs-driven layer switch case (qeth_dev_layer2_store()),
where the need to free the current netdevice was not considered at all.
Note that free_netdev() takes care of the netif_napi_del() for us too.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using up 8 bytes in every ipaddr object to store SETIP/DELIP flags is
rather wasteful. Except for takeover eligibility, the flag values all
just depend on the address type, so determine them on demand.
While at it reorder the struct to fill an alignment hole.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On an IP event, current code tries to determine if the netdev belongs
to a L3 card by walking all qeth cards in the system, and then all of
their VLAN devices too. Short-cut the whole thing by identifying a L3
device through its netdev_ops.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract a helper that does the actual work & returns the right NOTIFY_*
responses, and start putting the temporary ipaddr container objects
on the stack rather than kmalloc'ing them. They are small, and this
reduces the confusion of which objects actually get added to qeth's
IP tables.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
init_qdio_queues() resets the Input Queue's overall QDIO state, and
positions the buffer cursor back to 0. So this is the obvious place to
also reset the queue's NAPI context (in contrast to doing it rather
randomly in the middle of the big set_online() path).
No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newly-allocated skbs default to PACKET_HOST, and eth_type_trans() is
smart enough to determine any other packet type from the frame's
destination address.
So except for the IQD sniffer case, there is no need to set up
skb->pkt_type manually.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_alloc_skb() doesn't need to disable IRQs during the allocation,
and thus may save us a few cycles.
Doing so requires a small fix-up in the HiperTransport path, which
currently assumes a fixed NET_SKB_PAD headroom padding. napi_alloc_skb()
adds an additional NET_IP_ALIGN padding, so use the proper helper for
setting up the mac_header offset.
Use this opportunity to convert the non-NAPI path to netdev_alloc_skb(),
which means that skb->dev is now always set-up during allocation and
doesn't need to be assigned manually.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to pass the *payload* length, not the L2 address length.
For qeth (using eth_header()) this is merely a cosmetic change:
the parameter only matters when building headers for ETH_P_802_2
or ETH_P_802_3, whereas our fake headers are built with
ETH_P_IP / ETH_P_IPV6 / 0.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth implements HW-based Unicast Filtering (via SETVMAC) on L2 devices.
Tell the stack, so it knows that receiving traffic for secondary
addresses doesn't require full-blown promiscuous mode.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETIF_F_SG support is currently limited to OSA (and for L2 even OSD)
devices. Advertise it for some more device types (OSM, L2 OSX, z/VM OSA)
that share the same code paths. For now, keep it switched off by
default on these devices.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'portname' attribute is deprecated and setting it has no effect.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"s390/qeth: fix SETIP command handling" introduced a new helper, apply
it driver-wide.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If multiple IPA commands are build & sent out concurrently,
fill_ipacmd_header() may assign a seqno value to a command that's
different from what send_control_data() later assigns to this command's
reply.
This is due to other commands passing through send_control_data(),
and incrementing card->seqno.ipa along the way.
So one IPA command has no reply that's waiting for its seqno, while some
other IPA command has multiple reply objects waiting for it.
Only one of those waiting replies wins, and the other(s) times out and
triggers a recovery via send_ipa_cmd().
Fix this by making sure that the same seqno value is assigned to
a command and its reply object.
Do so immediately before submitting the command & while holding the
irq_pending "lock", to produce nicely ascending seqnos.
As a side effect, *all* IPA commands now use a reply object that's
waiting for its actual seqno. Previously, early IPA commands that were
submitted while the card was still DOWN used the "catch-all" IDX seqno.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code ("qeth_l3_ip_from_hash()") matches a queried address object
against objects in the IP table by IP address, Mask/Prefix Length and
MAC address ("qeth_l3_ipaddrs_is_equal()"). But what callers actually
require is either
a) "is this IP address registered" (ie. match by IP address only),
before adding a new address.
b) or "is this address object registered" (ie. match all relevant
attributes), before deleting an address.
Right now
1. the ADD path is too strict in its lookup, and eg. doesn't detect
conflicts between an existing NORMAL address and a new VIPA address
(because the NORMAL address will have mask != 0, while VIPA has
a mask == 0),
2. the DELETE path is not strict enough, and eg. allows del_rxip() to
delete a VIPA address as long as the IP address matches.
Fix all this by adding helpers (_addr_match_ip() and _addr_match_all())
that do the appropriate checking.
Note that the ADD path for NORMAL addresses is special, as qeth keeps
track of how many times such an address is in use (and there is no
immediate way of returning errors to the caller). So when a requested
NORMAL address _fully_ matches an existing one, it's not considered a
conflict and we merely increment the refcount.
Fixes: 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit cb816192d9.
The issue this attempted to fix never actually occurs.
l3_add_rxip() checks (via l3_ip_from_hash()) if the requested address
was previously added to the card. If so, it returns -EEXIST and doesn't
call l3_add_ip().
As a result, the "address exists" path in l3_add_ip() is never taken
for rxip addresses, and this patch had no effect.
Fixes: cb816192d9 ("s390/qeth: fix using of ref counter for rxip addresses")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Registering an IPv4 address with the HW takes quite a while, so we
temporarily drop the ip_htable lock. Any concurrent add/remove of the
same IP adjusts the IP's use count, and (on remove) is then blocked by
addr->in_progress.
After the register call has completed, we check the use count for
concurrently attempted add/remove calls - and possibly straight-away
deregister the IP again. This happens via l3_delete_ip(), which
1) looks up the queried IP in the htable (getting a reference to the
*same* queried object),
2) deregisters the IP from the HW, and
3) frees the IP object.
The caller in l3_add_ip() then does a second free on the same object.
For this case, skip all the extra checks and lookups in l3_delete_ip()
and just deregister & free the IP object ourselves.
Fixes: 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the HW is not reachable, then none of the IPs in qeth's internal
table has been registered with the HW yet. So when deleting such an IP,
there's no need to stage it for deregistration - just drop it from
the table.
This fixes the "add-delete-add" scenario on an offline card, where the
the second "add" merely increments the IP's use count. But as the IP is
still set to DISP_ADDR_DELETE from the previous "delete" step,
l3_recover_ip() won't register it with the HW when the card goes online.
Fixes: 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_get_elements_for_range() doesn't know how to handle a 0-length
range (ie. start == end), and returns 1 when it should return 0.
Such ranges occur on TSO skbs, where the L2/L3/L4 headers (and thus all
of the skb's linear data) are skipped when mapping the skb into regular
buffer elements.
This overestimation may cause several performance-related issues:
1. sub-optimal IO buffer selection, where the next buffer gets selected
even though the skb would actually still fit into the current buffer.
2. forced linearization, if the element count for a non-linear skb
exceeds QETH_MAX_BUFFER_ELEMENTS.
Rather than modifying qeth_get_elements_for_range() and adding overhead
to every caller, fix up those callers that are in risk of passing a
0-length range.
Fixes: 2863c61334 ("qeth: refactor calculation of SBALE count")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
send_control_data() applies some special handling to SETIP v4 IPA
commands. But current code parses *all* command types for the SETIP
command code. Limit the command code check to IPA commands.
Fixes: 5b54e16f1a ("qeth: do not spin for SETIP ip assist command")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For a memory range/skb where the last byte falls onto a page boundary
(ie. 'end' is of the form xxx...xxx001), the PFN_UP() part of the
calculation currently doesn't round up to the next PFN due to an
off-by-one error.
Thus qeth believes that the skb occupies one page less than it
actually does, and may select a IO buffer that doesn't have enough spare
buffer elements to fit all of the skb's data.
HW detects this as a malformed buffer descriptor, and raises an
exception which then triggers device recovery.
Fixes: 2863c61334 ("qeth: refactor calculation of SBALE count")
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The transport mode that a z/VM NIC is configured in, must match the
hypervisor-internal network which the NIC is coupled to.
To get this right automatically, have qeth issue a diag26c hypervisor call
that provides all sorts of information for a specific VNIC.
With z/VM update VM65918, this also includes the VNIC's required
transport mode.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By parameterising the address type, we need just one helper that walks
the IP table and builds up the response string.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding & removing IP entries for rxip/vipa/ipato/hsuid, forward any
resulting errors back to the sysfs-level caller.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of overlapping changes. Also on the net-next side
the XDP state management is handled more in the generic
layers so undo the 'net' nfp fix which isn't applicable
in net-next.
Include a necessary change by Jakub Kicinski, with log message:
====================
cls_bpf no longer takes care of offload tracking. Make sure
netdevsim performs necessary checks. This fixes a warning
caused by TC trying to remove a filter it has not added.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a common helper for parsing an IP address string, let's use it.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TSO and IQD paths already need to fix-up the current values, and
OSA will require more flexibility in the future as well. So just let
the caller specify the data length.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate the cast type translation, move the passthru path out of
the RCU-guarded section, and use the appropriate rtable helpers when
determining the next-hop address.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The L3 packet descriptor's 'dest_addr' field is used for a different
purpose in RX descriptors. Clean up the hard-coded byte accesses and
try to be more self-documenting.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When
1. an skb has no neighbour, and
2. skb->protocol is not IP[V6],
we select the skb's cast type based on its destination MAC address.
The multicast check is currently restricted to Multicast IP-mapped MACs.
Extend it to also cover non-IP Multicast MACs.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the proper helpers to check for multicast IP addressing, and remove
some ancient Token Ring code.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of assuming that skb->data points to the Ethernet header, use
the right helper and struct to access the Ethertype field.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once all of qeth_l3_set_rx_mode()'s single-use helpers are folded back
in, the two implementations actually look quite similar. So improve the
readability by converting both set_rx_mode() routines to a common
format.
This also allows us to walk ip_mc_htable just once, instead of three
times.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be a little more self-documenting, and get rid of OSA_ADDR_LEN.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For adding/removing a MAC address, use just one helper each that
handles both unicast and multicast.
Saves one level of indirection for multicast addresses, while improving
the error reporting for unicast addresses.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of tracking the uc/mc state in each MAC address object, just
check the multicast bit in the address itself.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit "s390/qeth: use ip*_eth_mc_map helpers" removed the last
occurrence of CONFIG_IPV6-dependent code.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of some wrapper indirection, and stop accessing the skb at
hard-coded offsets.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
atomic_t variables are currently used to implement reference
counters with the following properties:
- counter is initialized to 1 using atomic_set()
- a resource is freed upon counter reaching zero
- once counter reaches zero, its further
increments aren't allowed
- counter schema uses basic atomic operations
(set, inc, inc_not_zero, dec_and_test, etc.)
Such atomic variables should be converted to a newly provided
refcount_t type and API that prevents accidental counter overflows
and underflows. This is important since overflows and underflows
can lead to use-after-free situation and be exploitable.
The variable qeth_reply.refcnt is used as pure reference counter.
Convert it to refcount_t and fix up the operations.
Suggested-by: Kees Cook <keescook@chromium.org>
Reviewed-by: David Windsor <dwindsor@gmail.com>
Reviewed-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
[jwi: removed the WARN_ONs. Use CONFIG_REFCOUNT_FULL if you care.]
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
atomic_t variables are currently used to implement reference
counters with the following properties:
- counter is initialized to 1 using atomic_set()
- a resource is freed upon counter reaching zero
- once counter reaches zero, its further
increments aren't allowed
- counter schema uses basic atomic operations
(set, inc, inc_not_zero, dec_and_test, etc.)
Such atomic variables should be converted to a newly provided
refcount_t type and API that prevents accidental counter overflows
and underflows. This is important since overflows and underflows
can lead to use-after-free situation and be exploitable.
The variable lcs_reply.refcnt is used as pure reference counter.
Convert it to refcount_t and fix up the operations.
Suggested-by: Kees Cook <keescook@chromium.org>
Reviewed-by: David Windsor <dwindsor@gmail.com>
Reviewed-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
[jwi: removed the WARN_ONs. Use CONFIG_REFCOUNT_FULL if you care.]
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to check both return code fields before processing the
response. Otherwise we risk operating on invalid data.
Fixes: c9475369bd ("s390/qeth: rework RX/TX checksum offload")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any modification to the takeover IP-ranges requires that we re-evaluate
which IP addresses are takeover-eligible. Otherwise we might do takeover
for some addresses when we no longer should, or vice-versa.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modifying the flags of an IP addr object needs to be protected against
eg. concurrent removal of the same object from the IP table.
Fixes: 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When takeover is switched off, current code clears the 'TAKEOVER' flag on
all IPs. But the flag is also used for RXIP addresses, and those should
not be affected by the takeover mode.
Fix the behaviour by consistenly applying takover logic to NORMAL
addresses only.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just as for an explicit enable/disable, toggling the takeover mode also
requires that the IP addresses get updated. Otherwise all IPs that were
added to the table before the mode-toggle, get registered with the old
settings.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the correct SPDX license to a few more files under arch/s390 and
drivers/s390 which have been missed to far.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull networking fixes from David Miller:
1) Various TCP control block fixes, including one that crashes with
SELinux, from David Ahern and Eric Dumazet.
2) Fix ACK generation in rxrpc, from David Howells.
3) ipvlan doesn't set the mark properly in the ipv4 route lookup key,
from Gao Feng.
4) SIT configuration doesn't take on the frag_off ipv4 field
configuration properly, fix from Hangbin Liu.
5) TSO can fail after device down/up on stmmac, fix from Lars Persson.
6) Various bpftool fixes (mostly in JSON handling) from Quentin Monnet.
7) Various SKB leak fixes in vhost/tun/tap (mostly observed as
performance problems). From Wei Xu.
8) mvpps's TX descriptors were not zero initialized, from Yan Markman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (57 commits)
tcp: use IPCB instead of TCP_SKB_CB in inet_exact_dif_match()
tcp: add tcp_v4_fill_cb()/tcp_v4_restore_cb()
rxrpc: Fix the MAINTAINERS record
rxrpc: Use correct netns source in rxrpc_release_sock()
liquidio: fix incorrect indentation of assignment statement
stmmac: reset last TSO segment size after device open
ipvlan: Add the skb->mark as flow4's member to lookup route
s390/qeth: build max size GSO skbs on L2 devices
s390/qeth: fix GSO throughput regression
s390/qeth: fix thinko in IPv4 multicast address tracking
tap: free skb if flags error
tun: free skb in early errors
vhost: fix skb leak in handle_rx()
bnxt_en: Fix a variable scoping in bnxt_hwrm_do_send_msg()
bnxt_en: fix dst/src fid for vxlan encap/decap actions
bnxt_en: wildcard smac while creating tunnel decap filter
bnxt_en: Need to unconditionally shut down RoCE in bnxt_shutdown
phylink: ensure we take the link down when phylink_stop() is called
sfp: warn about modules requiring address change sequence
sfp: improve RX_LOS handling
...
The current GSO skb size limit was copy&pasted over from the L3 path,
where it is needed due to a TSO limitation.
As L2 devices don't offer TSO support (and thus all GSO skbs are
segmented before they reach the driver), there's no reason to restrict
the stack in how large it may build the GSO skbs.
Fixes: d52aec97e5 ("qeth: enable scatter/gather in layer 2 mode")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using GSO with small MTUs currently results in a substantial throughput
regression - which is caused by how qeth needs to map non-linear skbs
into its IO buffer elements:
compared to a linear skb, each GSO-segmented skb effectively consumes
twice as many buffer elements (ie two instead of one) due to the
additional header-only part. This causes the Output Queue to be
congested with low-utilized IO buffers.
Fix this as follows:
If the MSS is low enough so that a non-SG GSO segmentation produces
order-0 skbs (currently ~3500 byte), opt out from NETIF_F_SG. This is
where we anticipate the biggest savings, since an SG-enabled
GSO segmentation produces skbs that always consume at least two
buffer elements.
Larger MSS values continue to get a SG-enabled GSO segmentation, since
1) the relative overhead of the additional header-only buffer element
becomes less noticeable, and
2) the linearization overhead increases.
With the throughput regression fixed, re-enable NETIF_F_SG by default to
reap the significant CPU savings of GSO.
Fixes: 5722963a8e ("qeth: do not turn on SG per default")
Reported-by: Nils Hoppmann <niho@de.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
reworked how secondary addresses are managed for qeth devices.
Instead of dropping & subsequently re-adding all addresses on every
ndo_set_rx_mode() call, qeth now keeps track of the addresses that are
currently registered with the HW.
On a ndo_set_rx_mode(), we thus only need to do (de-)registration
requests for the addresses that have actually changed.
On L3 devices, the lookup for IPv4 Multicast addresses checks the wrong
hashtable - and thus never finds a match. As a result, we first delete
*all* such addresses, and then re-add them again. So each set_rx_mode()
causes a short period where the IPv4 Multicast addresses are not
registered, and the card stops forwarding inbound traffic for them.
Fix this by setting the ->is_multicast flag on the lookup object, thus
enabling qeth_l3_ip_from_hash() to search the correct hashtable and
find a match there.
Fixes: 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull s390 fixes from Martin Schwidefsky:
- SPDX identifiers are added to more of the s390 specific files.
- The ELF_ET_DYN_BASE base patch from Kees is reverted, with the change
some old 31-bit programs crash.
- Bug fixes and cleanups.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (29 commits)
s390/gs: add compat regset for the guarded storage broadcast control block
s390: revert ELF_ET_DYN_BASE base changes
s390: Remove redundant license text
s390: crypto: Remove redundant license text
s390: include: Remove redundant license text
s390: kernel: Remove redundant license text
s390: add SPDX identifiers to the remaining files
s390: appldata: add SPDX identifiers to the remaining files
s390: pci: add SPDX identifiers to the remaining files
s390: mm: add SPDX identifiers to the remaining files
s390: crypto: add SPDX identifiers to the remaining files
s390: kernel: add SPDX identifiers to the remaining files
s390: sthyi: add SPDX identifiers to the remaining files
s390: drivers: Remove redundant license text
s390: crypto: Remove redundant license text
s390: virtio: add SPDX identifiers to the remaining files
s390: scsi: zfcp_aux: add SPDX identifier
s390: net: add SPDX identifiers to the remaining files
s390: char: add SPDX identifiers to the remaining files
s390: cio: add SPDX identifiers to the remaining files
...
Now that the SPDX tag is in all drivers/s390/ files, that identifies the
license in a specific and legally-defined manner. So the extra GPL text
wording can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Cc: Ursula Braun <ubraun@linux.vnet.ibm.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Halil Pasic <pasic@linux.vnet.ibm.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/s390/net/ files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of
the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Cc: Ursula Braun <ubraun@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This mechanically converts all remaining cases of ancient open-coded timer
setup with the old setup_timer() API, which is the first step in timer
conversions. This has no behavioral changes, since it ultimately just
changes the order of assignment to fields of struct timer_list when
finding variations of:
init_timer(&t);
f.function = timer_callback;
t.data = timer_callback_arg;
to be converted into:
setup_timer(&t, timer_callback, timer_callback_arg);
The conversion is done with the following Coccinelle script, which
is an improved version of scripts/cocci/api/setup_timer.cocci, in the
following ways:
- assignments-before-init_timer() cases
- limit the .data case removal to the specific struct timer_list instance
- handling calls by dereference (timer->field vs timer.field)
spatch --very-quiet --all-includes --include-headers \
-I ./arch/x86/include -I ./arch/x86/include/generated \
-I ./include -I ./arch/x86/include/uapi \
-I ./arch/x86/include/generated/uapi -I ./include/uapi \
-I ./include/generated/uapi --include ./include/linux/kconfig.h \
--dir . \
--cocci-file ~/src/data/setup_timer.cocci
@fix_address_of@
expression e;
@@
init_timer(
-&(e)
+&e
, ...)
// Match the common cases first to avoid Coccinelle parsing loops with
// "... when" clauses.
@match_immediate_function_data_after_init_timer@
expression e, func, da;
@@
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
(
-\(e.function\|e->function\) = func;
-\(e.data\|e->data\) = da;
|
-\(e.data\|e->data\) = da;
-\(e.function\|e->function\) = func;
)
@match_immediate_function_data_before_init_timer@
expression e, func, da;
@@
(
-\(e.function\|e->function\) = func;
-\(e.data\|e->data\) = da;
|
-\(e.data\|e->data\) = da;
-\(e.function\|e->function\) = func;
)
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
@match_function_and_data_after_init_timer@
expression e, e2, e3, e4, e5, func, da;
@@
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
... when != func = e2
when != da = e3
(
-e.function = func;
... when != da = e4
-e.data = da;
|
-e->function = func;
... when != da = e4
-e->data = da;
|
-e.data = da;
... when != func = e5
-e.function = func;
|
-e->data = da;
... when != func = e5
-e->function = func;
)
@match_function_and_data_before_init_timer@
expression e, e2, e3, e4, e5, func, da;
@@
(
-e.function = func;
... when != da = e4
-e.data = da;
|
-e->function = func;
... when != da = e4
-e->data = da;
|
-e.data = da;
... when != func = e5
-e.function = func;
|
-e->data = da;
... when != func = e5
-e->function = func;
)
... when != func = e2
when != da = e3
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
@r1 exists@
expression t;
identifier f;
position p;
@@
f(...) { ... when any
init_timer@p(\(&t\|t\))
... when any
}
@r2 exists@
expression r1.t;
identifier g != r1.f;
expression e8;
@@
g(...) { ... when any
\(t.data\|t->data\) = e8
... when any
}
// It is dangerous to use setup_timer if data field is initialized
// in another function.
@script:python depends on r2@
p << r1.p;
@@
cocci.include_match(False)
@r3@
expression r1.t, func, e7;
position r1.p;
@@
(
-init_timer@p(&t);
+setup_timer(&t, func, 0UL);
... when != func = e7
-t.function = func;
|
-t.function = func;
... when != func = e7
-init_timer@p(&t);
+setup_timer(&t, func, 0UL);
|
-init_timer@p(t);
+setup_timer(t, func, 0UL);
... when != func = e7
-t->function = func;
|
-t->function = func;
... when != func = e7
-init_timer@p(t);
+setup_timer(t, func, 0UL);
)
Signed-off-by: Kees Cook <keescook@chromium.org>
Pull networking updates from David Miller:
"Highlights:
1) Maintain the TCP retransmit queue using an rbtree, with 1GB
windows at 100Gb this really has become necessary. From Eric
Dumazet.
2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.
3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
Lunn.
4) Add meter action support to openvswitch, from Andy Zhou.
5) Add a data meta pointer for BPF accessible packets, from Daniel
Borkmann.
6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.
7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.
8) More work to move the RTNL mutex down, from Florian Westphal.
9) Add 'bpftool' utility, to help with bpf program introspection.
From Jakub Kicinski.
10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
Dangaard Brouer.
11) Support 'blocks' of transformations in the packet scheduler which
can span multiple network devices, from Jiri Pirko.
12) TC flower offload support in cxgb4, from Kumar Sanghvi.
13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
Leitner.
14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.
15) Add RED qdisc offloadability, and use it in mlxsw driver. From
Nogah Frankel.
16) eBPF based device controller for cgroup v2, from Roman Gushchin.
17) Add some fundamental tracepoints for TCP, from Song Liu.
18) Remove garbage collection from ipv6 route layer, this is a
significant accomplishment. From Wei Wang.
19) Add multicast route offload support to mlxsw, from Yotam Gigi"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
tcp: highest_sack fix
geneve: fix fill_info when link down
bpf: fix lockdep splat
net: cdc_ncm: GetNtbFormat endian fix
openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
netem: remove unnecessary 64 bit modulus
netem: use 64 bit divide by rate
tcp: Namespace-ify sysctl_tcp_default_congestion_control
net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
ipv6: set all.accept_dad to 0 by default
uapi: fix linux/tls.h userspace compilation error
usbnet: ipheth: prevent TX queue timeouts when device not ready
vhost_net: conditionally enable tx polling
uapi: fix linux/rxrpc.h userspace compilation errors
net: stmmac: fix LPI transitioning for dwmac4
atm: horizon: Fix irq release error
net-sysfs: trigger netlink notification on ifalias change via sysfs
openvswitch: Using kfree_rcu() to simplify the code
openvswitch: Make local function ovs_nsh_key_attr_size() static
openvswitch: Fix return value check in ovs_meter_cmd_features()
...
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
Pull s390 updates from Heiko Carstens:
"Since Martin is on vacation you get the s390 pull request for the
v4.15 merge window this time from me.
Besides a lot of cleanups and bug fixes these are the most important
changes:
- a new regset for runtime instrumentation registers
- hardware accelerated AES-GCM support for the aes_s390 module
- support for the new CEX6S crypto cards
- support for FORTIFY_SOURCE
- addition of missing z13 and new z14 instructions to the in-kernel
disassembler
- generate opcode tables for the in-kernel disassembler out of a
simple text file instead of having to manually maintain those
tables
- fast memset16, memset32 and memset64 implementations
- removal of named saved segment support
- hardware counter support for z14
- queued spinlocks and queued rwlocks implementations for s390
- use the stack_depth tracking feature for s390 BPF JIT
- a new s390_sthyi system call which emulates the sthyi (store
hypervisor information) instruction
- removal of the old KVM virtio transport
- an s390 specific CPU alternatives implementation which is used in
the new spinlock code"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (88 commits)
MAINTAINERS: add virtio-ccw.h to virtio/s390 section
s390/noexec: execute kexec datamover without DAT
s390: fix transactional execution control register handling
s390/bpf: take advantage of stack_depth tracking
s390: simplify transactional execution elf hwcap handling
s390/zcrypt: Rework struct ap_qact_ap_info.
s390/virtio: remove unused header file kvm_virtio.h
s390: avoid undefined behaviour
s390/disassembler: generate opcode tables from text file
s390/disassembler: remove insn_to_mnemonic()
s390/dasd: avoid calling do_gettimeofday()
s390: vfio-ccw: Do not attempt to free no-op, test and tic cda.
s390: remove named saved segment support
s390/archrandom: Reconsider s390 arch random implementation
s390/pci: do not require AIS facility
s390/qdio: sanitize put_indicator
s390/qdio: use atomic_cmpxchg
s390/nmi: avoid using long-displacement facility
s390: pass endianness info to sparse
s390/decompressor: remove informational messages
...
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A few lines down, qeth_prepare_control_data() makes further changes to
the control cmd buffer, and then also writes a trace entry for it.
So the first entry just pollutes the trace file with intermediate data,
drop it.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to napi_complete_done(), and thus enable delayed GRO flushing.
The timeout is configured via /sys/class/net/<if>/gro_flush_timeout.
Default timeout is 0, so no change in behaviour.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code bails out when two subsequent buffer elements hold
insufficient data to contain a qeth_hdr packet descriptor.
This seems reasonable, but it would be legal for quirky hardware to
leave a few elements empty and then present packets in a subsequent
element. These packets would currently be dropped.
So make sure to check all buffer elements, until we hit the LAST_ENTRY
indication.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the allocation of SG skbs into the main path. This allows for
a little code sharing, and handling ENOMEM from within one place.
As side effect, L2 SG skbs now get the proper amount of additional
headroom (read: zero) instead of the hard-coded ETH_HLEN.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the open-coded skb_add_rx_frag(), and use a fall-through
to remove some duplicated code.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of silently discarding VLAN registration requests on OSM,
just indicate that this card type doesn't support VLAN.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no reason why l2_set_mac_address() should ever be called for
a netdevice that's not owned by qeth. It's certainly not required for
VLAN devices, which have their own netdev_ops.
Also:
1) we don't do such validation for any of the other netdev_ops routines.
2) the code in question clearly has never been actually exercised;
it's broken. After determining that the device is not owned
by qeth, it would still use dev->ml_priv to write a qeth trace entry.
Remove the check, and its helper that walked the global card list.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Drop the support for Token Ring,
2. use the ETH_DATA_LEN macro for the default L2 MTU,
3. handle OSM via the default case (as OSM is L2-only), and
4. document why the L3 MTU is reduced.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the allocation of the addr buffer fails, we need to free
our refcount on the inetdevice before returning.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sysfs enabled value is a boolean, so kstrtobool() is a better fit
for parsing the input string since it does the range checking for us.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit "s390/ccwgroup: tie a ccwgroup driver to its ccw driver",
the ccwgroup core now ensures that a qeth group device only consists of
ccw devices which are supported by qeth. Therefore remove qeth's
internal device matching, and use .driver_info to determine the card
type.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When recovering a device, qeth needs to re-run the IPA commands that
enable all previously active HW features.
Instead of duplicating qeth_set_features(), let netdev_update_features()
recover the missing HW features from dev->wanted_features.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two errors found their way into the timer callback conversions that
weren't noticed with x86 allmodconfig.
Reported-by: kernel test robot <lkp@01.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20171005171035.GA34831@beast
Remove uses of init_timer_on_stack() with open-coded function and data
assignments that could be expressed using timer_setup_on_stack(). Several
were removed from the stack entirely since there was a one-to-one mapping
of parent structure to timer, those are switched to using timer_setup()
instead. All related callbacks were adjusted to use from_timer().
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Petr Mladek <pmladek@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux1394-devel@lists.sourceforge.net
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: linux-s390@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: linux-scsi@vger.kernel.org
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Ursula Braun <ubraun@linux.vnet.ibm.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Harish Patil <harish.patil@cavium.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Reed <mdr@sgi.com>
Cc: Manish Chopra <manish.chopra@cavium.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-pm@vger.kernel.org
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Mark Gross <mark.gross@intel.com>
Cc: linux-watchdog@vger.kernel.org
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: netdev@vger.kernel.org
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lkml.kernel.org/r/1507159627-127660-4-git-send-email-keescook@chromium.org
When grouping devices, the ccwgroup core only checks whether all of the
devices are bound to the same ccw_driver. It has no means of checking
if the requesting ccwgroup driver actually supports this device type.
qeth implements its own device matching in qeth_core_probe_device(),
while ctcm and lcs currently have no sanity-checking at all.
Enable ccwgroup drivers to optionally defer the device type checking to
the ccwgroup core, by specifying their supported ccw_driver.
This allows us drop the device type matching from qeth, and improves
the robustness of ctcm and lcs.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cppcheck reports the following for drivers/s390/net/qeth_core.h:
warning - line 1560 - Function 'qeth_do_send_packet' argument order
different:
declaration 'card, queue, skb, hdr, hd_len, offset, elements'
definition 'card, queue, skb, hdr, offset, hd_len, elements_needed'.
Match the naming in the function's declaration against its definition.
Signed-off-by: Jens Remus <jremus@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the overly complicated VLAN processing from the L3 RX handler into
its l3_rebuild_skb() helper. No change in functionality.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Properly return any error encountered during VLAN processing to the
the caller.
Resulting change in behaviour: if SETVLAN fails while registering a
new VLAN ID, the stack no longer creates the corresponding vlan device.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the right helpers to create/remove all attribute groups in one go.
Suggested-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Locking the output queue prior to TX is needed on OSA devices,
to synchronize against a packing flush from the TX completion code
(via qeth_check_outbound_queue()).
But send_packet_fast() is only used for IQDs, which don't do packing.
So remove the locking, and apply some easy cleanups.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Storing the number of input buffers into 'i' has no effect, it is
immediately re-assigned in the next line.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HiperSockets allow configuring so called VNIC Characteristics (VNICC)
that influence how the underlying hardware handles packets. For VNICCs,
additional commands for getting and setting timeouts are available.
Currently, the learning VNICC uses these commands.
* Learning VNICC: If learning is enabled on a qeth device, the device
learns the source MAC addresses of outgoing packets and incoming
packets to those learned MAC addresses are received.
For learning, the timeout specifies the idle period in seconds, after
which the underlying hardware removes a learned MAC address again.
This patch adds support for the IPA commands that are required to get
and set the current timeout values for the learning VNIC characteristic.
Also, it introduces the sysfs interface that allows users to configure
the timeout.
Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HiperSocket devices allow enabling and disabling so called VNIC
Characteristics (VNICC) that influence how the underlying hardware
handles packets. These VNICCs are:
* Flooding VNICC: Flooding allows specifying if packets to unknown
destination MAC addresses are received by the qeth device.
* Multicast flooding VNICC: Multicast flooding allows specifying if
packets to multicast MAC addresses are received by the qeth device.
* Learning VNICC: If learning is enabled on a qeth device, the device
learns the source MAC addresses of outgoing packets and incoming
packets to those learned MAC addresses are received.
* Takeover setvmac VNICC: If takeover setvmac is configured on a qeth
device, the MAC address of this device can be configured on a
different qeth device with the setvmac IPA command.
* Takeover by learning VNICC: If takeover learning is enabled on a qeth
device, the MAC address of this device can be learned (learning VNICC)
on a different qeth device.
* BridgePort invisible VNICC: If BridgePort invisible is enabled on a
qeth device, (1) packets from this device are not sent to a BridgePort
enabled qeth device and (2) packets coming from a BridgePort enabled
qeth device are not received by this device.
* Receive broadcast VNICC: Receive broadcast allows configuring if a
qeth device receives packets with the broadcast destination MAC
address.
This patch adds support for the IPA commands that are required to enable
and disable these VNIC characteristics on qeth devices. As a
prerequisite, it also adds the query commands IPA command.
The query commands IPA command allows requesting the supported commands
for each characteristic from the underlying hardware.
Additionally, this patch provides users with a sysfs user interface to
enable/disable the VNICCs mentioned above.
Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VNIC Characteristics (VNICC) are features of HiperSockets that define
how packets are handled by the underlying network hardware. For example,
if the VNICC flooding is configured on a qeth device, ethernet frames to
unknown destination MAC addresses are received.
Currently, there is support for seven VNICCs: flooding, multicast
flooding, receive broadcast, learning, takeover learning, takeover
setvmac, bridge invisible. Also, six IPA commands exist for configuring
VNICCs on a qeth device: query characteristics, query commands, enable
characteristic, disable characteristic, set timeout, get timeout.
This patch adds the basic code infrastructure for VNICC support to qeth.
It allows querying VNICC support from the underlying hardware. To this
end, it adds:
* basic message formats for IPA commands
* basic data structures
* basic error handling
* query characteristics IPA command support
The query characteristics IPA command allows requesting the currently
supported and currently enabled VNIC characteristics from the underlying
hardware.
Support for the other IPA commands and for the configuration of VNICCs
is added in follow-up patches together with the respective user
interface functions.
Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Support ipv6 checksum offload in sunvnet driver, from Shannon
Nelson.
2) Move to RB-tree instead of custom AVL code in inetpeer, from Eric
Dumazet.
3) Allow generic XDP to work on virtual devices, from John Fastabend.
4) Add bpf device maps and XDP_REDIRECT, which can be used to build
arbitrary switching frameworks using XDP. From John Fastabend.
5) Remove UFO offloads from the tree, gave us little other than bugs.
6) Remove the IPSEC flow cache, from Florian Westphal.
7) Support ipv6 route offload in mlxsw driver.
8) Support VF representors in bnxt_en, from Sathya Perla.
9) Add support for forward error correction modes to ethtool, from
Vidya Sagar Ravipati.
10) Add time filter for packet scheduler action dumping, from Jamal Hadi
Salim.
11) Extend the zerocopy sendmsg() used by virtio and tap to regular
sockets via MSG_ZEROCOPY. From Willem de Bruijn.
12) Significantly rework value tracking in the BPF verifier, from Edward
Cree.
13) Add new jump instructions to eBPF, from Daniel Borkmann.
14) Rework rtnetlink plumbing so that operations can be run without
taking the RTNL semaphore. From Florian Westphal.
15) Support XDP in tap driver, from Jason Wang.
16) Add 32-bit eBPF JIT for ARM, from Shubham Bansal.
17) Add Huawei hinic ethernet driver.
18) Allow to report MD5 keys in TCP inet_diag dumps, from Ivan
Delalande.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1780 commits)
i40e: point wb_desc at the nvm_wb_desc during i40e_read_nvm_aq
i40e: avoid NVM acquire deadlock during NVM update
drivers: net: xgene: Remove return statement from void function
drivers: net: xgene: Configure tx/rx delay for ACPI
drivers: net: xgene: Read tx/rx delay for ACPI
rocker: fix kcalloc parameter order
rds: Fix non-atomic operation on shared flag variable
net: sched: don't use GFP_KERNEL under spin lock
vhost_net: correctly check tx avail during rx busy polling
net: mdio-mux: add mdio_mux parameter to mdio_mux_init()
rxrpc: Make service connection lookup always check for retry
net: stmmac: Delete dead code for MDIO registration
gianfar: Fix Tx flow control deactivation
cxgb4: Ignore MPS_TX_INT_CAUSE[Bubble] for T6
cxgb4: Fix pause frame count in t4_get_port_stats
cxgb4: fix memory leak
tun: rename generic_xdp to skb_xdp
tun: reserve extra headroom only when XDP is set
net: dsa: bcm_sf2: Configure IMP port TC2QOS mapping
net: dsa: bcm_sf2: Advertise number of egress queues
...
Pull s390 updates from Martin Schwidefsky:
"The first part of the s390 updates for 4.14:
- Add machine type 0x3906 for IBM z14
- Add IBM z14 TLB flushing improvements for KVM guests
- Exploit the TOD clock epoch extension to provide a continuous TOD
clock afer 2042/09/17
- Add NIAI spinlock hints for IBM z14
- Rework the vmcp driver and use CMA for the respone buffer of z/VM
CP commands
- Drop some s390 specific asm headers and use the generic version
- Add block discard for DASD-FBA devices under z/VM
- Add average request times to DASD statistics
- A few of those constify patches which seem to be in vogue right now
- Cleanup and bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (50 commits)
s390/mm: avoid empty zero pages for KVM guests to avoid postcopy hangs
s390/dasd: Add discard support for FBA devices
s390/zcrypt: make CPRBX const
s390/uaccess: avoid mvcos jump label
s390/mm: use generic mm_hooks
s390/facilities: fix typo
s390/vmcp: simplify vmcp_response_free()
s390/topology: Remove the unused parent_node() macro
s390/dasd: Change unsigned long long to unsigned long
s390/smp: convert cpuhp_setup_state() return code to zero on success
s390: fix 'novx' early parameter handling
s390/dasd: add average request times to dasd statistics
s390/scm: use common completion path
s390/pci: log changes to uid checking
s390/vmcp: simplify vmcp_ioctl()
s390/vmcp: return -ENOTTY for unknown ioctl commands
s390/vmcp: split vmcp header file and move to uapi
s390/vmcp: make use of contiguous memory allocator
s390/cpcmd,vmcp: avoid GFP_DMA allocations
s390/vmcp: fix uaccess check and avoid undefined behavior
...
Taking a full copy via skb_realloc_headroom() on every xmit is overkill
and wastes CPU time; all we actually need is to push on the qeth_hdr.
So rework the L2 OSA TX path to avoid the copy.
Minor complications arise because struct qeth_hdr must not cross a page
boundary. So add a new helper qeth_push_hdr() that catches this, and
falls back to the hdr cache that we already use for IQDs.
This change uncovered that qeth's TX completion takes rather long.
Now that we no longer free the original skb straight away and thus call
skb->destructor later than before, throughput regresses significantly.
For now, restore old behaviour by adding an explicit skb_orphan(),
and a big TODO to improve the TX completion time.
Tested-by: Nils Hoppmann <niho@de.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After plenty of refactoring, use hd_len as single indication that
the skb needs a dedicated header element.
This preserves existing behaviour for TSO, as 'hdr' always points
to skb->data.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a prerequisite for unifying the code to build header elements.
The TSO header has a different size, so we can no longer rely on implicitly
adding the size of a normal qeth_hdr.
No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For TSO we need to skip the skb's qeth/IP/TCP headers when mapping
it into buffer elements. Instead of (mis)using skb_pull(), pass a
corresponding offset to fill_buffer() like we already do for IQDs.
No actual change in the resulting TSO buffers.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TSO code already calculates the length of its header element,
no need to duplicate this in the low-level code again.
Use this opportunity to make hd_len unsigned, and for TSO match
its calculation to what tso_fill_header() does.
No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For IQD we already need to fix up the qeth_hdr's length field, and
future changes will require more flexibility for OSA as well. The
device-specific path knows best what header length it requires, so just
pass it from there.
While at it, remove the unused qeth_card parameter.
No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2_hard_start_xmit() actually doesn't contain much shared code,
and having device-specific paths makes isolated changes a lot easier.
So split it into three routines for IQD, OSN and OSD/OSM/OSX.
No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP-address setting and removal are delayed when the device is not yet in
state SOFTSETUP or UP. ref_counter has been implemented only for
ip-address with type normal. In this patch ref_counter logic is also used
for ip-address with type rxip to allow appropriate handling of multiple
postponed rxip add and del calls.
Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
change trace-messages:
- from addrxip4 to delrxip4
- from addrxip6 to delrxip6
Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There exist different commands to add unicast and multicast addresses on
the OSA card. rxip addresses are always set as unicast addresses and
thus just unicast addresses should be allowed.
Adding a multicast address now fails and a grace message is generated.
Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidation of duplicated code, no functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up the inline cruft in s390 net drivers. Many of the inlined
functions had only one caller anyway.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace some open-coded parts with their proper API calls.
Also remove two skb_[re]set_mac_header() calls in the L2
xmit paths that are clearly no longer required, since at least
commit 6d1ccff627 ("net: reset mac header in dev_start_xmit()").
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some xmit paths we pass down a data offset to qeth_fill_buffer(),
to indicate that the first k bytes of the skb should be skipped when
mapping it into buffer elements.
Commit acd9776b5c ("s390/qeth: no ETH header for outbound AF_IUCV")
recently switched the offset for the IUCV-over-HiperSockets path
from 0 to ETH_HLEN, and now we have
device offset
OSA = 0
IQD > 0
for all xmit paths.
OSA would previously pass down -1 from do_send_packet(), to distinguish
between 1) OSA and 2) IQD with offset 0. That's no longer needed now,
so have it pass 0, make the offset unsigned and clean up how we apply
the offset in __qeth_fill_buffer().
No change of behaviour for any of our current xmit paths.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. for adjusting the buffer's next_element_to_fill in __fill_buffer(),
just pass the full qeth_qdio_out_buffer struct
2. when adding a header element, be consistent about passing
a hint ('is_first_elem') to __fill_buffer()
No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve readability of the code that determines a buffer element's
fragment type, and reduce the number of cases down from 5 to 3.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_l3_setadapter_parms() queries the device for supported
adapterparms, even though they already have been queried as part of the
device's high-level setup. Remove that extra call.
The only call chain for qeth_l3_setadapter_parms() is
__qeth_l3_set_online()
qeth_core_hardsetup_card()
qeth_query_setadapterparms()
qeth_l3_setadapter_parms()
qeth_query_setadapterparms()
, and we only reach qeth_l3_setadapter_parms() if the first
adapterparms query succeeds. Hence removing the second query results in
no loss of functionality.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_l2_request_initial_mac() queries the device for its supported
adapterparms, even though they already have been queried as part of the
device's high-level setup. Remove that extra call.
The only call chain for qeth_l2_request_initial_mac() is
__qeth_l2_set_online()
qeth_core_hardsetup_card()
qeth_query_setadapterparms()
qeth_l2_setup_netdev()
qeth_l2_request_initial_mac()
qeth_query_setadapterparms()
, and we only reach qeth_l2_request_initial_mac() if the first
adapterparms query succeeds. Hence removing the second query results in
no loss of functionality.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After transmitting a skb via send_packet[_fast](), the statistics
code accesses the skb once more to account for transmitted page frags.
This has a (theoretical?) race against the TX completion - if the TX
completion is processed and frees the skb before hard_start_xmit()
gets to the statistics part, we access random memory.
Fix this by caching the # of page frags, before the skb is transmitted.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On L3, the qeth_hdr struct needs to be filled with the next-hop
IP address.
The current code accesses rtable->rt_gateway without checking that
rtable is a valid address. The accidental access to a lowcore area
results in a random next-hop address in the qeth_hdr.
rtable (or more precisely, skb_dst(skb)) can be NULL in rare cases
(for instance together with AF_PACKET sockets).
This patch adds the missing NULL-ptr checks.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Fixes: 87e7597b5a qeth: Move away from using neighbour entries in qeth_l3_fill_header()
Signed-off-by: David S. Miller <davem@davemloft.net>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
6763 1216 0 7979 1f2b drivers/s390/net/qeth_l3_sys.o
File size After adding 'const':
text data bss dec hex filename
7019 960 0 7971 1f2b drivers/s390/net/qeth_l3_sys.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make the code like the rest of the kernel.
Link: http://lkml.kernel.org/r/3f980cd89084ae09716353aba3171e4b3815e690.1499284835.git.joe@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Cc: Ursula Braun <ubraun@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
"Reasonably busy this cycle, but perhaps not as busy as in the 4.12
merge window:
1) Several optimizations for UDP processing under high load from
Paolo Abeni.
2) Support pacing internally in TCP when using the sch_fq packet
scheduler for this is not practical. From Eric Dumazet.
3) Support mutliple filter chains per qdisc, from Jiri Pirko.
4) Move to 1ms TCP timestamp clock, from Eric Dumazet.
5) Add batch dequeueing to vhost_net, from Jason Wang.
6) Flesh out more completely SCTP checksum offload support, from
Davide Caratti.
7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
Neira Ayuso, and Matthias Schiffer.
8) Add devlink support to nfp driver, from Simon Horman.
9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
Prabhu.
10) Add stack depth tracking to BPF verifier and use this information
in the various eBPF JITs. From Alexei Starovoitov.
11) Support XDP on qed device VFs, from Yuval Mintz.
12) Introduce BPF PROG ID for better introspection of installed BPF
programs. From Martin KaFai Lau.
13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.
14) For loads, allow narrower accesses in bpf verifier checking, from
Yonghong Song.
15) Support MIPS in the BPF selftests and samples infrastructure, the
MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
Daney.
16) Support kernel based TLS, from Dave Watson and others.
17) Remove completely DST garbage collection, from Wei Wang.
18) Allow installing TCP MD5 rules using prefixes, from Ivan
Delalande.
19) Add XDP support to Intel i40e driver, from Björn Töpel
20) Add support for TC flower offload in nfp driver, from Simon
Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
Kicinski, and Bert van Leeuwen.
21) IPSEC offloading support in mlx5, from Ilan Tayari.
22) Add HW PTP support to macb driver, from Rafal Ozieblo.
23) Networking refcount_t conversions, From Elena Reshetova.
24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
for tuning the TCP sockopt settings of a group of applications,
currently via CGROUPs"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
cxgb4: Support for get_ts_info ethtool method
cxgb4: Add PTP Hardware Clock (PHC) support
cxgb4: time stamping interface for PTP
nfp: default to chained metadata prepend format
nfp: remove legacy MAC address lookup
nfp: improve order of interfaces in breakout mode
net: macb: remove extraneous return when MACB_EXT_DESC is defined
bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
bpf: fix return in load_bpf_file
mpls: fix rtm policy in mpls_getroute
net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
...
Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpX4A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymobgCfd0d13IfpZoq1N41wc6z2Z0xD7cwAnRMeH1/p
kEeISGpHPYP9f8PBh9FO
=Hfqt
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues"
* tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (56 commits)
arm: mach-rpc: ecard: fix build error
zram: convert remaining CLASS_ATTR() to CLASS_ATTR_RO()
driver-core: remove struct bus_type.dev_attrs
powerpc: vio_cmo: use dev_groups and not dev_attrs for bus_type
powerpc: vio: use dev_groups and not dev_attrs for bus_type
USB: usbip: convert to use DRIVER_ATTR_RW
s390: drivers: convert to use DRIVER_ATTR_RO/WO
platform: thinkpad_acpi: convert to use DRIVER_ATTR_RO/RW
pcmcia: ds: convert to use DRIVER_ATTR_RO
wireless: ipw2x00: convert to use DRIVER_ATTR_RW
net: ehea: convert to use DRIVER_ATTR_RO
net: caif: convert to use DRIVER_ATTR_RO
TTY: hvc: convert to use DRIVER_ATTR_RW
PCI: pci-driver: convert to use DRIVER_ATTR_WO
IB: nes: convert to use DRIVER_ATTR_RW
HID: hid-core: convert to use DRIVER_ATTR_RO and drv_groups
arm: ecard: fix dev_groups patch typo
tty: serdev: use dev_groups and not dev_attrs for bus_type
sparc: vio: use dev_groups and not dev_attrs for bus_type
hid: intel-ish-hid: use dev_groups and not dev_attrs for bus_type
...
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a s390 guest runs on a z/VM host that's part of a SSI cluster,
it can be migrated to a different host. In this case, the MAC address
it originally obtained on the old host may be re-assigned to a new
guest. This would result in address conflicts between the two guests.
When running as z/VM guest, use the diag26c MAC Service to obtain
a hypervisor-managed MAC address. The MAC Service is SSI-aware, and
won't re-assign the address after the guest is migrated to a new host.
This patch adds support for the z/VM MAC Service on L2 devices.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's two spots in qeth_send_packet() where we don't accurately
account for transmitted packing buffers in qeth's performance
statistics:
1) when flushing the current buffer due to insufficient size,
and the next buffer is not EMPTY, we need to account for that
flushed buffer.
2) when synchronizing with the TX completion code, we reset
flush_count and thus forget to account for any previously
flushed buffers.
Reported-by: Nils Hoppmann <niho@de.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add ipa return codes for Bridgeport (HiperSockets and OSA) according to
system level design.
Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are trying to get rid of DRIVER_ATTR(), and the s390 drivers'
attributes can be trivially changed to use DRIVER_ATTR_RO() and
DRIVER_ATTR_WO().
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Cc: Ursula Braun <ubraun@linux.vnet.ibm.com>
Cc: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: <linux-s390@vger.kernel.org>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
qeth currently supports early setup for OSM and OSN devices.
This patch adds early setup support for z/VM HiperSockets,
since they can only be coupled to L3 networks.
Based on an initial version by Dmitriy Lakhvich.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to how qeth currently does early L2 setup of OSM and OSN
devices, add support for early setup of L3-only devices.
This adds a qeth_l3_devtype that contains all core and l3-specific
sysfs attributes, so that they can be created in one go while probing.
This just adds the infrastructure, exploitation of the support happens
in a subsequent patch.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noting the lack of TSO support on every feature change is just silly,
in particular since the requested features might not even affect
NETIF_F_TSO.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_switch_to_nonpacking_if_needed() contains an open-coded version
of qeth_flush_buffers_on_no_pci(). Extract a single helper instead.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 76b11f8e27 ("qeth: HiperSockets Network Traffic Analyzer")
missed adding the human-readable translations when adding new RCs.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridgeport is a l2-specific feature, and we should write its
capabilities to a debug entry.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HiperSocket devices don't need the full IPv6 initialization, but we
should still query the supported assists for logging purposes.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth doesn't advertise NETIF_F_SG for L3 IQDs. So trust the stack to
not hand us any nonlinear skbs, and remove an always-true condition.
With the fact that data_offset < 0 is no longer possible on IQDs,
apply a small cleanup to subsequent code.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This Assist was never actually implemented in any hardware, so just
remove the leftovers.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
added new hash tables, but missed to initialize them.
Fixes: 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Access card->dev only after checking whether's its valid.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit b4d72c08b3 ("qeth: bridgeport support - basic control")
broke the support for OSM and OSN devices as follows:
As OSM and OSN are L2 only, qeth_core_probe_device() does an early
setup by loading the l2 discipline and calling qeth_l2_probe_device().
In this context, adding the l2-specific bridgeport sysfs attributes
via qeth_l2_create_device_attributes() hits a BUG_ON in fs/sysfs/group.c,
since the basic sysfs infrastructure for the device hasn't been
established yet.
Note that OSN actually has its own unique sysfs attributes
(qeth_osn_devtype), so the additional attributes shouldn't be created
at all.
For OSM, add a new qeth_l2_devtype that contains all the common
and l2-specific sysfs attributes.
When qeth_core_probe_device() does early setup for OSM or OSN, assign
the corresponding devtype so that the ccwgroup probe code creates the
full set of sysfs attributes.
This allows us to skip qeth_l2_create_device_attributes() in case
of an early setup.
Any device that can't do early setup will initially have only the
generic sysfs attributes, and when it's probed later
qeth_l2_probe_device() adds the l2-specific attributes.
If an early-setup device is removed (by calling ccwgroup_ungroup()),
device_unregister() will - using the devtype - delete the
l2-specific attributes before qeth_l2_remove_device() is called.
So make sure to not remove them twice.
What complicates the issue is that qeth_l2_probe_device() and
qeth_l2_remove_device() is also called on a device when its
layer2 attribute changes (ie. its layer mode is switched).
For early-setup devices this wouldn't work properly - we wouldn't
remove the l2-specific attributes when switching to L3.
But switching the layer mode doesn't actually make any sense;
we already decided that the device can only operate in L2!
So just refuse to switch the layer mode on such devices. Note that
OSN doesn't have a layer2 attribute, so we only need to special-case
OSM.
Based on an initial patch by Ursula Braun.
Fixes: b4d72c08b3 ("qeth: bridgeport support - basic control")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting up the device from within the layer discipline's
probe routine, creating the layer-specific sysfs attributes can fail.
Report this error back to the caller, and handle it by
releasing the layer discipline.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
[jwi: updated commit msg, moved an OSN change to a subsequent patch]
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
prepare() and complete() are not implemented by any discipline, so just
drop all the indirection.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LINK_MODE_* replaces the u32-limited SUPPORTED_* / ENABLED_*
definitions.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
get_settings() is deprecated and lacks support for higher link
speeds, so implement get_link_ksettings() instead.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for moving to get_link_ksettings(), clean up how
we build the supported and advertised port/speed masks.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. a buffer has 16 is_header flags, because that's its # of elements
2. replace the last occurrence of QETH_HEADER_SIZE, and remove it
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_start_xmit() expects us to return netdev_tx_t here...
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'elements_needed' is not used in qeth_do_send_packet_fast(),
so consequently remove it.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Duplicated code.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Identical code, we just need to call a layer-specific hook
to process any received buffer.
qeth_buffer_reclaim_work() is shuffled around to avoid a
forward declaration for qeth_queue_input_buffer().
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a number of layer-independent ioctls that we can handle
in core, and reduce code duplication. For layer-specific ioctls,
add a do_ioctl() discipline hook.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace ntohs with endianness conversion for the SKB protocol assignment
to avoid an endianness warning reported by sparse. No functional change.
Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use endianness conversions for SKB protocol assignments and usage to
avoid endianness warnings reported by sparse. No functional changes.
Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid endianness warnings reported by sparse by (1) using endianness
conversions for assigning and using network packet fields, and (2)
removing unnecessary endianness conversions from qeth_l3_rebuild_skb. No
functional changes.
Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. options.add_hhlen is set but never used, drop it
2. clean up no longer required forward declarations
3. delete all sorts of unused defines
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_qdio_output_handler() is the only caller of
qeth_handle_send_error() and doesn't care about the return value.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ac fields are bitmaps, so format them as hex.
While at it, also print the ac2 field.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
better use the constant definitions.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With AF_IUCV traffic, the skb passed to hard_start_xmit() has a 14 byte
slot at skb->data, intended for an ETH header. qeth_l3_fill_af_iucv_hdr()
fills this ETH header... and then immediately moves it to the
skb's headroom, where it disappears and is never seen again.
But it's still possible for us to return NETDEV_TX_BUSY after the skb has
been modified. Since we didn't get a private copy of the skb, the next
time the skb is delivered to hard_start_xmit() it no longer has the
expected layout (we moved the ETH header to the headroom, so skb->data
now starts at the IUCV_TRANS header). So when qeth_l3_fill_af_iucv_hdr()
does another round of rebuilding, the resulting qeth header ends up
all wrong. On transmission, the buffer is then rejected by
the HiperSockets device with SBALF15 = x'04'.
When this error is passed back to af_iucv as TX_NOTIFY_UNREACHABLE, it
tears down the offending socket.
As the ETH header for AF_IUCV serves no purpose, just align the code to
what we do for IP traffic on L3 HiperSockets: keep the ETH header at
skb->data, and pass down data_offset = ETH_HLEN to qeth_fill_buffer().
When mapping the payload into the SBAL elements, the ETH header is then
stripped off. This avoids the skb manipulations in
qeth_l3_fill_af_iucv_hdr(), and any buffer re-entering hard_start_xmit()
after NETDEV_TX_BUSY is now processed properly.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on the device type, hard_start_xmit() builds different output
buffer formats. For instance with HiperSockets, on both L2 and L3 we
strip the ETH header from the skb - L3 doesn't need it, and L2 carries
it in the buffer's header element.
For this, we pass data_offset = ETH_HLEN all the way down to
__qeth_fill_buffer(), where skb->data is then adjusted accordingly.
But the initial size calculation still considers the *full* skb length
(including the ETH header). So qeth_get_elements_no() can erroneously
reject a skb as too big, even though it would actually fit into an
output buffer once the ETH header has been trimmed off later.
Fix this by passing an additional offset to qeth_get_elements_no(),
that indicates where in the skb the on-wire data actually begins.
Since the current code uses data_offset=-1 for some special handling
on OSA, we need to clamp data_offset to 0...
On HiperSockets this helps when sending ~MTU-size skbs with weird page
alignment. No change for OSA or AF_IUCV.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth devices in layer3 mode need a separate handling of vipa and proxy-arp
addresses. vipa and proxy-arp addresses processed by qeth can be read from
userspace. Introduced with commit 5f78e29cee ("qeth: optimize IP handling
in rx_mode callback") the retrieval of vipa and proxy-arp addresses is
broken, if more than one vipa or proxy-arp address are set.
The qeth code used local variable "int i" for 2 different purposes. This
patch now spends 2 separate local variables of type "int".
While touching these functions hash_for_each_safe() is converted to
hash_for_each(), since there is no removal of hash entries.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reference-ID: RQM 3524
Signed-off-by: David S. Miller <davem@davemloft.net>
STARTLAN needs to be the first IPA command after MPC initialization
completes.
So move the qeth_send_startlan() call from the layer disciplines
into the core path, right after the MPC handshake.
While at it, replace the magic LAN OFFLINE return code
with the existing enum.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all MAC utility functions in one place, and drop the
forward declarations.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This matches qeth_l2_write_mac().
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate errno handling for MAC management: Instead of doing this in every
caller, do it in one place.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Suggested-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_l2_send_groupmac() already translates the return code, so
calling qeth_setdel_makerc() a second time only produces garbage.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only caller passes del = 0, so remove both the parameter and
the code that handles != 0.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accessing the current hsuid via card->options.hsuid is perfectly
fine, even when the card is DOWN.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RX/TX checksum offloading is turned on and the adapter is
an OSA 3 card in layer 3 mode, the checksum offloading is only
performed when both peers use different adapters. If both peers
share an OSA 3 card, communication is a memory copy and
checksum offloading is not performed.
This patch adds a warning to inform the administrator.
OSA 3 in layer 2 mode does not offer the RX/TX checksum
offload feature.
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turning on receive and/or transmit checksum offload support
on the OSA card requires 2 commands:
1. start command which replies with available features
2. enable command to turn on selected features.
The current version does not check the reply of the start
command and simply uses the returned value to enable
offload features. When the start command returns zero, this
leads to a situation where no checksum offload
is turned on by the hardware. Even worse no error
indication is returned. The Linux kernel assumes
the OSA card performs RX/TX checksum offload, but the hardware
does not perform any checksum verification at all.
This patch checks the return of the start and enable
command responses from the hardware and turns off
checksum offloading if the commands fails or does not
respond with the correct bit setting.
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework the RX/TX checksum offloading command sequence to use
the provided function call back mechanims to return card
data to the device driver.
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a trailing white space at the end of a dev_err
message that does nothing useful - remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
High values are always wrong for netiucv's sysfs attribute "buffer".
But the current code does not detect values between 2**31 and 2**32
as invalid. Choosing type "unsigned int" for variable "bs1" and making
use of "kstrtouint()" improves the syntax checking for "buffer".
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Save a memcpy in netiucv_printuser().
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
restructured the internal address handling.
This work broke setting a virtual IP address.
The command
echo 10.1.1.1 > /sys/bus/ccwgroup/devices/<device>/vipa/add4
fails with file exist error even if the IP address has not
been set before.
It turned out that the search result for the IP address
search is handled incorrectly in the VIPA case.
This patch fixes the setting of an virtual IP address.
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to recent performance measurements, turning on net_device
feature NETIF_F_SG only behaves well, but turning on feature
NETIF_F_GSO shows bad results. Since the kernel activates NETIF_F_GSO
automatically as soon as the driver configures feature NETIF_F_SG, qeth
should not activate feature NETIF_F_SG per default, until the qeth
problems with NETIF_F_GSO are solved.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller