The layer 3 exceptions are still subject to the same trap policer, so
nothing changes, but user space can choose to assign a different one.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enable clk_ref failed, clk_ptp should be disabled rather than
clk_ref itself.
Signed-off-by: Liu Xiang <liuxiang_1999@126.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The removal of mips_swiotlb_ops exposed a problem in octeon_mgmt Ethernet
driver. mips_swiotlb_ops had an mb() after most of the operations and the
removal of the ops had broken the receive functionality of the driver.
My code inspection has shown no other places except
octeon_mgmt_rx_fill_ring() where an explicit barrier would be obviously
missing. The latter function however has to make sure that "ringing the
bell" doesn't happen before RX ring entry is really written.
The patch has been successfully tested on Octeon II.
Fixes: a999933db9 ("MIPS: remove mips_swiotlb_ops")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register ndo callback via flow_indr_dev_register() and
flow_indr_dev_unregister().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register ndo callback via flow_indr_dev_register() and
flow_indr_dev_unregister().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register ndo callback via flow_indr_dev_register() and
flow_indr_dev_unregister().
No need for mlx5e_rep_indr_clean_block_privs() since flow_block_cb_free()
already releases the internal mapping via ->release callback, which in
this case is mlx5e_rep_indr_tc_block_unbind().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shrink the code visually by replacing regmap_update_bits() with
appropriate regmap bit operations where applicable.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The caller doesn't care about the error codes, they only check for zero
vs non-zero. Still, it's better to preserve the negative error codes
from alloc_uld_rxqs() instead of changing it to 1. We can also return
directly if there is a failure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When proxy mode is enabled the vxlan device might reply to Neighbor
Solicitation (NS) messages on behalf of remote hosts.
In case the NS message includes the "Source link-layer address" option
[1], the vxlan device will use the specified address as the link-layer
destination address in its reply.
To avoid an infinite loop, break out of the options parsing loop when
encountering an option with length zero and disregard the NS message.
This is consistent with the IPv6 ndisc code and RFC 4886 which states
that "Nodes MUST silently discard an ND packet that contains an option
with length zero" [2].
[1] https://tools.ietf.org/html/rfc4861#section-4.3
[2] https://tools.ietf.org/html/rfc4861#section-4.6
Fixes: 4b29dba9c0 ("vxlan: fix nonfunctional neigh_reduce()")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
* many 6 GHz changes, though it's not _quite_ complete
(I left out scanning for now, we're still discussing)
* allow userspace SA-query processing for operating channel
validation
* TX status for control port TX, for AP-side operation
* more per-STA/TID control options
* move to kHz for channels, for future S1G operation
* various other small changes
-----BEGIN PGP SIGNATURE-----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=wdaG
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2020-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of changes, including
* many 6 GHz changes, though it's not _quite_ complete
(I left out scanning for now, we're still discussing)
* allow userspace SA-query processing for operating channel
validation
* TX status for control port TX, for AP-side operation
* more per-STA/TID control options
* move to kHz for channels, for future S1G operation
* various other small changes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting the PHY cfg (CQ cmd 0x0601), if the firmware responds
with an EMODE error, software will ignore the error as it simply
means that manageability (ex: BMC) is in control of the link and that
the new setting may not be applied.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The logic was missing for adding back perfect flows after flow director
filter delete. The code now adds perfect flows into the HW tables after
filter delete.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when a VSI is built (i.e. reset, set channels, etc.)
the coalesce settings will be preserved in most cases. However, when the
number of q_vectors are increased the settings for the new q_vectors
will be set to the driver defaults of AIM on, Rx/Tx ITR 50, and INTRL 0.
This is causing issues with how the ethtool layer gets the current
coalesce settings since it only uses q_vector 0. So, assume that the user
set the coalesce settings globally (i.e. ethtool -C eth0) and use q_vector
0's settings for all of the new q_vectors.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit ceb2f00707 ("ice: Use pci_get_dsn()") changed the code to
use a new function to get the Device Serial Number. It also changed
the case of the filename for loading a package on a specific NIC
from lowercase to uppercase. Change the filename back to
lowercase since that is what we specified.
Fixes: ceb2f00707 ("ice: Use pci_get_dsn()")
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Where possible, cuddle multiple lines of function signatures to be
consistent throughout the code.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A VF driver has the ability to request reset via VIRTCHNL_OP_RESET_VF.
This is a required step in VF driver load. Currently, the PF is only
allowing a VF to request reset using this method after the VF has
already communicated resources via VIRTCHNL_OP_GET_VF_RESOURCES.
However, this is incorrect because the VF can request reset before
requesting resources. Fix this by allowing the VF to request a reset
once it has been initialized.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the driver prevents a user from doing
modprobe ice
ethtool -L eth0 combined 5
ip link set eth0 up
The ethtool command fails, because the driver is checking to see if the
interface is down before allowing the get_channels to proceed (even for
a set_channels).
Remove this check and allow the user to configure the interface
before bringing it up, which is a much better usability case.
Fixes: 87324e747f ("ice: Implement ethtool ops for channels")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Always clear the previous value in QRXFLXP_CNTXT before writing a new
value. This will make it so re-used queues will not accidentally take the
previously configured settings.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the PF is modifying the VF's port VLAN on the fly when
configured via iproute. This is okay for most cases, but if the VF
already has guest VLANs configured the PF has to remove all of those
filters so only VLAN tagged traffic that matches the port VLAN will
pass. Instead of adding functionality to track which guest VLANs have
been added, just reset the VF each time port VLAN parameters are
modified.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As currently, we are supporting only 5 PHY_SPEEDs for phy_type_high.
Thus, we should adjust the value of ICE_PHY_TYPE_HIGH_MAX_INDEX to 5.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To allow for resets during package download, increase the timeout period
after performing a PFR. The time waited is the global config lock
timeout plus the normal PFSWR timeout.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the driver does not recognize when there is an 802.1AD VLAN
tag right after the dmac/smac (outermost VLAN tag). If any DCB map is
applied and/or DCB is enabled this is causing the hardware to insert a
VLAN 0 tag after the 802.1AD VLAN tag that is already in the packet.
Fix this by preventing VLAN tag 0 from being added when any VLAN is
already present after dmac/smac (software offloaded) or skb (hardware
offloaded).
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow untrusted VF to add 16 unicast/multicast filters. VF uses 1 filter
for the default/perm_addr/LAA MAC, 1 for broadcast, and 16 additional
unicast/multicast filters.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently a user is not allowed to clear a VF's administratively set MAC
on the PF. Fix this by allowing an all zero MAC address via "ip link set
${pf_eth} vf ${vf_id} mac 00:00:00:00:00:00".
An example use case for this would be issuing a "virsh shutdown"
command on a VM. The call to iproute mentioned above is part of this flow.
Without this change the driver incorrectly rejects clearing the VF's
administratively set MAC and prints unhelpful log messages.
Also, improve the comments surrounding this change.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Until recently, the Micrel KSZ9031 PHY driver ignored any PHY mode
("RGMII-*ID") settings, but used the hardware defaults, augmented by
explicit configuration of individual skew values using the "*-skew-ps"
DT properties. The lack of PHY mode support was compensated by the
EtherAVB MAC driver, which configures TX and/or RX internal delay
itself, based on the PHY mode.
However, now the KSZ9031 driver has gained PHY mode support, delays may
be configured twice, causing regressions. E.g. on the Renesas
Salvator-X board with R-Car M3-W ES1.0, TX performance dropped from ca.
400 Mbps to 0.1-0.3 Mbps, as measured by nuttcp.
As internal delay configuration supported by the KSZ9031 PHY is too
limited for some use cases, the ability to configure MAC internal delay
is deemed useful and necessary. Hence a proper fix would involve
splitting internal delay configuration in two parts, one for the PHY,
and one for the MAC. However, this would require adding new DT
properties, thus breaking DTB backwards-compatibility.
Hence fix the regression in a backwards-compatibility way, by letting
the EtherAVB driver mask the PHY mode when it has inserted a delay, to
avoid the PHY driver adding a second delay. This also fixes messages
like:
Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: *-skew-ps values should be used only with phy-mode = "rgmii"
as the PHY no longer sees the original RGMII-*ID mode.
Solving the issue by splitting configuration in two parts can be handled
in future patches, and would require retaining a backwards-compatibility
mode anyway.
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- remove fdb from nh_list before the rcu grace period
- protect fdb->vdev with rcu
- hold spin lock before destroying fdb
Fixes: c7cdbe2efc ("vxlan: support for nexthop notifiers")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NDA_NH_ID represents a remote ip or a group of remote ips.
It allows use of nexthop groups in lieu of a remote ip or a
list of remote ips supported by the fdb api.
Current code ignores the other remote ip attrs when NDA_NH_ID is
specified. In the spirit of strict checking, This commit adds a
check to explicitly return an error on incorrect usage.
Fixes: 1274e1cc42 ("vxlan: ecmp support for mac fdb entries")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2020-05-28
This series contains updates to the ice driver only.
Anirudh (Ani) adds a poll for reset completion before proceeding with
driver initialization when the DDP package fails to load and the firmware
issues a core reset.
Jake cleans up unnecessary code, since ice_set_dflt_vsi_ctx() performs a
memset to clear the info from the context structures. Fixed a potential
double free during probe unrolling after a failure. Also fixed a
potential NULL pointer dereference upon register_netdev() failure.
Tony makes two functions static which are not called outside of their
file.
Brett refactors the ice_ena_vf_mappings(), which was doing the VF's MSIx
and queue mapping in one function which was hard to digest. So create a
new function to handle the enabling MSIx mappings and another function
to handle the enabling of queue mappings. Simplify the code flow in
ice_sriov_configure(). Created a helper function for clearing
VPGEN_VFRTRIG register, as this needs to be done on reset to notify the
VF that we are done resetting it. Fixed the initialization/creation and
reset flows, which was unnecessarily complicated, so separate the two
flows into their own functions. Renamed VF initialization functions to
make it more clear what they do and why. Added functionality to set the
VF trust mode bit on reset. Added helper functions to rebuild the VLAN
and MAC configurations when resetting a VF. Refactored how the VF reset
is handled to prevent VF reset timeouts.
Paul cleaned up code not needed during a CORER/GLOBR reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify handling the power management callbacks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functionality for quiescing the chip is spread across different
functions currently. Move it to rtl8169_down().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move calls that are needed before and after calling rtl8169_hw_reset()
into this function. This requires to move the function in the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In places where the indexes have to be reset, we call
rtl8169_init_ring_indexes() anyway after rtl8169_tx_clear().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We go to runtime-suspend few secs after cable removal. As cable is
removed "physical link up" is the only meaningful WoL source.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change driver private data type to struct rtl8169_private * to avoid
some overhead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Third set of patches for v5.8. Final new features before the merge
window (most likely) opens, noteworthy here is adding WPA3 support to
old drivers rt2800, b43 and b43_legacy.
Major changes:
ath10k
* SDIO and SNOC busses are not experimental anymore
ath9k
* allow receive of broadcast Action frames
ath9k_htc
* allow receive of broadcast Action frames
rt2800
* enable WPA3 support out of box
b43
* enable WPA3 support
b43_legacy
* enable WPA3 support
mwifiex
* advertise max number of clients to user space
mt76
* mt7663: add remain-on-channel support
* mt7915: add spatial reuse support
* add support for mt7611n hardware
iwlwifi
* add ACPI DSM support
* support enabling 5.2GHz bands in Indonesia via ACPI
* bump FW API version to 56
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJe0nFMAAoJEG4XJFUm622bf04H/1IqM/9Wpt6qMSa+adBz5ij7
yNwWCD2nXAgyirafRIot6uoOY7ePfutwwUXD5IatwPFIEQVZP/uoRDqBPqsbz85J
w5Izvpt15eG5uSDuy5rLUFucOz3XJZQkOGWRo/GKGSLjm2uPGGXAVul+fWX+i05J
xfH1GvLys//An/X6AIx6kWqyJYqUfmxXj7pLkiOYFlt8JNS49gDaA1Emvv7/xv+Q
hyBswKjNrEeT5K4dqYjQ/hp9/ukX8JQtpVBRF7rth5T8gxzJQmOKiP86L8YH5SyI
r3U3ok1aUIuG6xhsTV/cWkqQeD6YsO9M1dTO1WQQLQyZgwl/esbjw/4BVNMGgVk=
=9pX4
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-05-30' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.8
Third set of patches for v5.8. Final new features before the merge
window (most likely) opens, noteworthy here is adding WPA3 support to
old drivers rt2800, b43 and b43_legacy.
Major changes:
ath10k
* SDIO and SNOC busses are not experimental anymore
ath9k
* allow receive of broadcast Action frames
ath9k_htc
* allow receive of broadcast Action frames
rt2800
* enable WPA3 support out of box
b43
* enable WPA3 support
b43_legacy
* enable WPA3 support
mwifiex
* advertise max number of clients to user space
mt76
* mt7663: add remain-on-channel support
* mt7915: add spatial reuse support
* add support for mt7611n hardware
iwlwifi
* add ACPI DSM support
* support enabling 5.2GHz bands in Indonesia via ACPI
* bump FW API version to 56
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The dynamic configuration interface for the General Params and the L2
Lookup Params tables was copy-pasted between E/T devices and P/Q/R/S
devices. Nonetheless, these interfaces are bitwise different.
The driver is using dynamic reconfiguration of the General Parameters
table for the port mirroring feature, which was therefore broken on
P/Q/R/S.
Note that this patch can't be backported easily very far to stable trees
(since it conflicts with some other development done since the
introduction of the driver). So the Fixes: tag is purely informational.
Fixes: 8aa9ebccae ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer compilers complain with W=1 builds that there are non-static
functions defined in sja1105_static_config.c that don't have a
prototype, because their prototype is defined in sja1105.h which this
translation unit does not include.
I don't entirely understand what is the point of these warnings, since
in principle there's nothing wrong with that. But let's move the
prototypes to a header file that _is_ included by
sja1105_static_config.c, since that will make these warnings go away.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accumulated cleanup patches and sparse warning fixes for mlx5 driver.
1) sync with mlx5-next branch
2) Eli Cohen declares mpls_entry_encode() helper in mpls.h as suggested
by Jakub Kicinski and David Ahern, and use it in mlx5
3) Jesper Fixes xdp data_meta setup in mlx5
4) Many sparse and build warnings cleanup
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl7R3wcACgkQSD+KveBX
+j6/ZQf/QD39naPeImfLjemkRK9L+TKbS4nU6wpUwf1jC33Wdm4HhkhsWEnR6C4l
OwU/Pae3I9EtKP4gRE0W1o8h7zC9h4hY7+IKZOdyQ32iUY55PX/H25oqAiCj1NCM
xzWpXOTwK/vkqmkCedAd+YpNdYlbOhfycr+KVPSsvFdaPqjzfNO1PJcLsUbAbzrX
A+8pYdhUYTtx1N3YHJL5abLN6WzMAKxgwlm9GG8YCXACTJT6CBWWHGebVsC5TDUk
Lj5hJj38mI8/3dcu6vWP0kLGVfRZo0HS/gpPGxbKQFpP+1uBYaRENAQONxkY++6S
GDPix7ccvN+yNMlON893PC/Cogw3Yg==
=WaCJ
-----END PGP SIGNATURE-----
Merge tag 'mlx5-cleanup-2020-05-29' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-cleanup-2020-05-29
Accumulated cleanup patches and sparse warning fixes for mlx5 driver.
1) sync with mlx5-next branch
2) Eli Cohen declares mpls_entry_encode() helper in mpls.h as suggested
by Jakub Kicinski and David Ahern, and use it in mlx5
3) Jesper Fixes xdp data_meta setup in mlx5
4) Many sparse and build warnings cleanup
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
NETIF_F_HW_VLAN_CTAG_FILTER is not set in netdev->hw_feature for
the HNS3 driver, so the handler of NETIF_F_HW_VLAN_CTAG_FILTER
in hns3_nic_set_features() won't be called, remove it.
Reported-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a redundant blank line in hclgevf_cmd_set_promisc_mode(),
and fix a reverse xmas tree coding style issue in
hclgevf_set_rss_tc_mode().
Reported-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct hclgevf_dev stands for VF device, its field num_tqps
indicates the number of VF's task queue pairs, so the comment
is incorrect, replace 'PF' with 'VF'.
Reported-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macro hclgevf_ring_to_dma_dir and hclgevf_is_csq defined in
hclgevf_cmd.c, but not used, so remove them.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macro hclge_is_csq defined in hcgle_cmd.c has not been used,
so remove it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use %d to print int variable 'ret' in hclge_mac_mdio_config().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ath10k/qmi.h header file contains a declaration for the function
ath10k_qmi_register_service_notifier(). This function doesn't exist.
Remove the declaration.
This patch is a no-op and was just found by code inspection.
Fixes: ba94c753cc ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200528122105.1.I31937dce728b441fd72cbe23447bc4710fd56ddb@changeid
Advertise support for multicast frame registration and update the RX
filter based on the recently added FIF_MCAST_ACTION to allow broadcast
Action frames to be received. This is needed for Device Provisioning
Protocol (DPP) use cases that use broadcast Public Action frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200426084733.7889-2-jouni@codeaurora.org
Advertise support for multicast frame registration and update the RX
filter based on the recently added FIF_MCAST_ACTION to allow broadcast
Action frames to be received. This is needed for Device Provisioning
Protocol (DPP) use cases that use broadcast Public Action frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200426084733.7889-1-jouni@codeaurora.org
Fix sparse warning:
drivers/net/ethernet/mellanox/mlx5/core/en_dcbnl.c:988:29:
error: symbol 'mlx5e_dcbnl_ops' was not declared. Should it be static?
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix some trivial warnings of the type:
warning: incorrect type in initializer (different base types)
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
tls handle and rcd_sn are actually big endian and not in host format.
Fix that.
Fix the following sparse warnings:
drivers/net/ethernet/mellanox/mlx5/core/en_accel/tls.c:177:21:
warning: cast to restricted __be64
drivers/net/ethernet/mellanox/mlx5/core/en_accel/tls.c:178:52:
warning: incorrect type in argument 2 (different base types)
expected unsigned int [usertype] handle
got restricted __be32 [usertype] handle
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix sparse warning:
drivers/net/ethernet/mellanox/mlx5/core/cmd.c:1949:15:
warning: memset with byte count of 271720
mlx5_cmd_stats array is too big to be held inline in mlx5_cmd.
Allocate it separately.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
dr_ste_crc32_calc() calculates crc32 and should return it in HW format.
It is being used to calculate a u32 index, hence we force the return value
of u32 to avoid the sparse warning:
drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste.c:115:16:
warning: incorrect type in return expression (different base types)
expected unsigned int
got restricted __be32 [usertype]
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
raw_ip actual type is __be32 and not u32.
Fix that and get rid of the warning.
drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste.c:906:31:
warning: cast to restricted __be32
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
HW spec objects should receive a void ptr to work on, the MLX5_SET/GET
macro will know how to handle it.
No need to provide explicit or wrong pointer type in this case.
warning: incorrect type in argument 1 (different base types)
expected unsigned long long const [usertype] *sw_action
got restricted __be64 [usertype] *[assigned] sw_action
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Make use of generic API mpls_entry_encode() to build mpls label and get
rid of local function.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Moving the mlx5_ifc_query_qp_out_bits structure on the stack was a bit
excessive and now causes the compiler to complain on 32-bit architectures:
drivers/net/ethernet/mellanox/mlx5/core/debugfs.c: In function 'qp_read_field':
drivers/net/ethernet/mellanox/mlx5/core/debugfs.c:274:1: error: the frame size of 1104 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Revert the previous patch partially to use dynamically allocation as
the code did before. Unfortunately there is no good error handling
in case the allocation fails.
Fixes: 57a6c5e992 ("net/mlx5: Replace hand written QP context struct with automatic getters")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Clang warns:
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:3712:6: warning:
variable 'err' is used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
if (IS_ERR(d->pkt_reformat)) {
^~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:3718:6: note:
uninitialized use occurs here
if (err)
^~~
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:3712:2: note: remove the
'if' if its condition is always true
if (IS_ERR(d->pkt_reformat)) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:3670:9: note: initialize
the variable 'err' to silence this warning
int err;
^
= 0
1 warning generated.
It is not wrong, err is only ever initialized in if statements but this
one is not in one. Initialize err to 0 to fix this.
Fixes: 14e6b038af ("net/mlx5e: Add support for hw decapsulation of MPLS over UDP")
Link: https://github.com/ClangBuiltLinux/linux/issues/1037
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The helper function xdp_set_data_meta_invalid() must be called after
setting xdp->data as it depends on it.
The bug was introduced in the cited patch below, and cause the kernel
to crash when using BPF helper bpf_xdp_adjust_head() on mlx5 driver.
Fixes: 39d6443c8d ("mlx5, xsk: Migrate to new MEM_TYPE_XSK_BUFF_POOL")
Reported-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
VNIC protocol version is reported in big-endian format, but it
is not byteswapped before logging. Fix that, and remove version
comparison as only one protocol version exists at this time.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous refactoring missed some locations the flags were renamed
but not moved from the previous flower_ext_feats to the new flower_en_feats
variable. This lead to the FLOW_MERGE and LAG features not being enabled.
Fixes: e09303d3c4 ("nfp: flower: renaming of feature bits")
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
NXP imx8 family like imx8mp/imx8dxl chips support Synopsys MAC 5.10a IP.
This patch adds settings for NXP imx8 glue layer:
- clocks
- dwmac address width
- phy interface mode selection
- adjust rgmii txclk rate
v2:
- adjust code sequences in order to have reverse christmas
tree local variable ordering.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add "snps,dwmac-5.10a" compatible string for 5.10a version that can
avoid to define some plat data in glue layer.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be there 2 switches spi/spi2.0 and spi/spi2.1 in a cross-chip setup,
both under the same VLAN-filtering bridge, both in the
SJA1105_VLAN_BEST_EFFORT state.
If we try to change the VLAN state of one of the switches (to
SJA1105_VLAN_FILTERING_FULL) we get the following error:
devlink dev param set spi/spi2.1 name best_effort_vlan_filtering value
false cmode runtime
[ 38.325683] sja1105 spi2.1: Not allowed to overcommit frame memory.
L2 memory partitions and VL memory partitions share the
same space. The sum of all 16 memory partitions is not
allowed to be larger than 929 128-byte blocks (or 910
with retagging). Please adjust
l2-forwarding-parameters-table.part_spc and/or
vl-forwarding-parameters-table.partspc.
[ 38.356803] sja1105 spi2.1: Invalid config, cannot upload
This is because the spi/spi2.1 switch doesn't support tagging anymore in
the SJA1105_VLAN_FILTERING_FULL state, so it doesn't need to have any
retagging rules defined. Great, so it can use more frame memory
(retagging consumes extra memory).
But the built-in low-level static config checker from the sja1105 driver
says "not so fast, you've increased the frame memory to non-retagging
values, but you still kept the retagging rules in the static config".
So we need to rebuild the VLAN table immediately before re-uploading the
static config, operation which will take care, based on the new VLAN
state, of removing the retagging rules.
Fixes: 3f01c91aab ("net: dsa: sja1105: implement VLAN retagging for dsa_8021q sub-VLANs")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5: Add ability to read and write ECE options
net/mlx5: Add support for RDMA TX FT headers modifying
net/mlx5: Move iseg access helper routines close to mlx5_core driver
net/mlx5: Cleanup mlx5_ifc_fte_match_set_misc2_bits
net/mlx5: Add support in forward to namespace
{IB/net}/mlx5: Simplify don't trap code
net/mlx5: Replace zero-length array with flexible-array
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The drivers reports EINVAL to userspace through netlink on invalid meta
match. This is confusing since EINVAL is usually reserved for malformed
netlink messages. Replace it by more meaningful codes.
Fixes: 6d65bc64e2 ("net/mlx5e: Add mlx5e_flower_parse_meta support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Change MLX5_TC_CT config dependencies to include MLX5_ESWITCH instead of
MLX5_CORE_EN && NET_SWITCHDEV, which are already required by MLX5_ESWITCH.
Without this change mlx5 fails to compile if user disables MLX5_ESWITCH
without also manually disabling MLX5_TC_CT.
Fixes: 4c3844d9e9 ("net/mlx5e: CT: Introduce connection tracking")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add a call to mlx5e_reset_rx/tx_moderation() when enabling/disabling
adaptive moderation, in order to select the proper default values.
In order to do so, we separate the logic of selecting the moderation values
and setting moderion mode (CQE/EQE based).
Fixes: 0088cbbc4b ("net/mlx5e: Enable CQE based moderation on TX CQ")
Fixes: 9908aa2929 ("net/mlx5e: CQE based moderation")
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Change type of active_fec to u32 to match the type expected by
mlx5e_get_fec_mode. Copy active_fec and configured_fec values to
unsigned long before preforming bitwise manipulations.
Take the same approach when configuring FEC over 50G link modes: copy
the policy into an unsigned long and only than preform bitwise
operations.
Fixes: 2132b71f78 ("net/mlx5e: Advertise globaly supported FEC modes")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
On tunnel decap rule insertion, the indirect mechanism will attempt to
offload the rule on all uplink representors which will trigger the
"devices are not on same switch HW, can't offload forwarding" message
for the uplink which isn't on the same switch HW as the VF representor.
The above flow is valid and shouldn't cause warning message,
fix by removing the warning and only report this flow using extack.
Fixes: 321348475d ("net/mlx5e: Fix allowed tc redirect merged eswitch offload cases")
Signed-off-by: Maor Dickman <maord@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently a Linux system with the mlx5 NIC always crashes upon
hibernation - suspend/resume.
Add basic callbacks so the NIC could be suspended and resumed.
Fixes: 9603b61de1 ("mlx5: Move pci device handling from mlx5_ib to mlx5_core")
Tested-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We need to call phy_restore_page() even if phy_select_page() fails.
Otherwise we are holding the phy_lock_mdio_bus() lock. This requirement
is documented at the start of the phy_select_page() function.
Fixes: a618e86da9 ("net : phy: marvell: Speedup TDR data retrieval by only changing page once")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHYs using the vsc8574_probe fail to be initialized and their
config_init return -EIO leading to errors like:
"could not attach PHY: -5".
This is because when the conversion of the MSCC PHY driver to use the
shared PHY package helpers was done, the base address retrieval and the
base PHY read and write helpers in the driver were modified. In
particular, the base address retrieval logic was moved from the
config_init to the probe. But the vsc8574_probe was forgotten. This
patch fixes it.
Fixes: deb04e9c0f ("net: phy: mscc: use phy_package_shared")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The desc pointer is set but not used. Remove it.
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 8c7bd5a454 ("net: ethernet: mtk-star-emac: new driver")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2020-05-28
This series contains updates to e1000, e1000e, igc, igb, ixgbe and i40e.
Takashi Iwai, from SUSE, replaces some uses of snprintf() with
scnprintf() since the succeeding calls may go beyond the given buffer
limit in i40e.
Jesper Dangaard Brouer fixes up code comments in i40e_xsk.c
Xie XiuQi, from Huawei, fixes a signed-integer-overflow warning ixgbe
driver.
Jason Yan, from Huawei, converts '==' expression to bool to resolve
warnings, also fixed a warning for assigning 0/1 to a bool variable in
the ixgbe driver. Converts functions that always return 0 to void in the
igb and i40e drivers.
YueHaibing, from Hauwei, cleans up dead code in ixgbe driver.
Sasha cleans up more dead code which is not used in the igc driver.
Added receive error counter to reflect the total number of non-filtered
packets received with errors. Fixed a register define name to properly
reflect the register address being used.
Andre updates the igc driver to reject NFC rules that have multiple
matches, which is not supported in i225 devices. Updates the total
number of NFC rules supported and added a code comment to explain what
is supported.
Punit Agrawal, from Toshiba, relaxes the condition to trigger a reset
for ME, which was leading to inconsistency between the state of the
hardware as expected by the driver in e1000e.
Hari, from the Linux community, cleaned up a code comment in the e1000
driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
'Commit dacce2be33 ("vmxnet3: add geneve and vxlan tunnel offload
support")' added support for encapsulation offload. However, while
preparing inner tso packet, it uses reference to outer ip headers.
This patch fixes this issue by using correct reference for inner
headers.
Fixes: dacce2be33 ("vmxnet3: add geneve and vxlan tunnel offload support")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Update range request API;
* Add ACPI DSM support;
* Support enabling 5.2GHz bands in Indonesia via ACPI;
* Bump FW API version to 56;
* TX queues refactoring started;
* Fix one memory leak;
* Some other small fixes and clean-ups;
-----BEGIN PGP SIGNATURE-----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=nlI2
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2020-05-29' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Third set of iwlwifi patches intended for v5.8
* Update range request API;
* Add ACPI DSM support;
* Support enabling 5.2GHz bands in Indonesia via ACPI;
* Bump FW API version to 56;
* TX queues refactoring started;
* Fix one memory leak;
* Some other small fixes and clean-ups;
# gpg: Signature made Fri 29 May 2020 10:38:28 AM EEST using RSA key ID 1A3CC5FA
# gpg: Good signature from "Luciano Roth Coelho (Luca) <luca@coelho.fi>"
# gpg: aka "Luciano Roth Coelho (Intel) <luciano.coelho@intel.com>"
SD8997 firmware sends TLV_TYPE_MAX_CONN with struct hw_spec_max_conn to
inform kernel about maximum number of p2p connections and stations in AP
mode.
During initialization of SD8997 wifi chip kernel prints warning:
mwifiex_sdio mmc0:0001:1: Unknown GET_HW_SPEC TLV type: 0x217
This patch adds support for parsing TLV_TYPE_MAX_CONN (0x217) and sets
appropriate cfg80211 member 'max_ap_assoc_sta' from retrieved structure.
It allows userspace to retrieve NL80211_ATTR_MAX_AP_ASSOC_STA attribute.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200521123559.29028-1-pali@kernel.org
During initialization of SD8997 wifi chip kernel prints warnings:
mwifiex_sdio mmc0:0001:1: Unknown api_id: 3
mwifiex_sdio mmc0:0001:1: Unknown api_id: 4
This patch adds support for parsing all api ids provided by SD8997
firmware.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200521123444.28957-1-pali@kernel.org
The problem is that we always copy a minimum of ETH_ZLEN (60) bytes from
skb->data even when skb->len is less than ETH_ZLEN so it leads to a read
overflow.
The fix is to pad skb->data to at least ETH_ZLEN bytes.
Cc: <stable@vger.kernel.org>
Reported-by: Hu Jiahui <kirin.say@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200527184830.GA1164846@mwanda
Set MES watermark size to 0x50 for 43012. It fixes SDIO bus hang issue
when running at high throughput.
Signed-off-by: Double Lo <double.lo@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529034938.124533-6-chi-hsien.lin@cypress.com
Set F2 blocksize to 256 bytes and watermark to 0x40 for 4354/4356 SDIO.
Also enable and configure F1 MesBusyCtrl. It would resolve random driver
crash issue.
Signed-off-by: Frank Kao <frank.kao@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529034938.124533-4-chi-hsien.lin@cypress.com
Set F2 blocksize to 256 bytes for 4373. It fixes DMA error while having
UDP bi-directional traffic. Also use a defined F1 MesBusyCtrl value.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529034938.124533-2-chi-hsien.lin@cypress.com
When wlcore_fw_status() returns an error code, a pairing
runtime PM usage counter decrement is needed to keep the
counter balanced. It's the same for all error paths after
wlcore_fw_status().
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522044906.29564-1-dinghao.liu@zju.edu.cn
The CCK TX setting when switch channel will fix the CCK to
path A only, so if the antenna is configured to path B
(e.g. iw phy set antenna 0x2 0x3 "TX B/RX AB"), then the CCK
packets can never be delivered to the air if only path B is
connected with an antenna (it can possibly be transmitted
through path A, but as path B is configured, the expected
behavior is incorrect).
This can also solve the racing issue of CCK TX setting between
driver and firmware. The CCK TX setting in driver should be
removed. Otherwise, the CCK TX setting would be wrong when the
racing occurs.
Fixes: 297bcf8222 ("rtw88: add support for set/get antennas")
Signed-off-by: Chien-Hsun Liao <ben.liao@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522091234.24495-1-yhchuang@realtek.com
For older versions of gcc, the array = {0}; will cause warnings:
drivers/net/wireless/realtek/rtw88/rtw8822c.c: In function 'rtw8822c_power_trim':
>> drivers/net/wireless/realtek/rtw88/rtw8822c.c:1039:2: warning:
>> missing braces around initializer [-Wmissing-braces]
s8 bb_gain[2][8] = {0};
^
drivers/net/wireless/realtek/rtw88/rtw8822c.c:1039:2: warning: (near
initialization for 'bb_gain[0]') [-Wmissing-braces]
Fixes: 5ad4d8957b ("rtw88: set power trim according to efuse PG values")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522035521.12295-1-yhchuang@realtek.com
Connecting to an AP with WPA2 security may fail. The IQK
and the EAPOL 4-way handshake may overlap because the
driver does IQK right after assoc success.
For 802.11n devices, the IQK is done in the driver and it
could require more than 100ms to complete. During IQK, any
TX/RX events are paused. So if the EAPOL 4-way handshake
started before IQK finished, then the 1/4 and 2/4 part of
the handshake could be dropped. The AP will then issue
deauth with reason IEEE8021X_FAILED (23).
To resolve this, move IQK routine into managed TX prepare
(ieee80211_ops::mgd_prepare_tx()). The callback is called
before the managed frames (auth/assoc) are sent. This will
make sure that the IQK is completed before the handshake
starts. But don't do IQK during scanning because doing it
on each channel will take too long.
For 802.11ac devices, the IQK is done in firmware and it
takes less time to complete. Therefore we don't see a
failure during the EAPOL 4-way handshake. But it is still
worth moving the IQK into ieee80211_ops::mgd_prepare_tx().
Fixes: f5df1a8b43 ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile")
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529025009.2468-4-yhchuang@realtek.com
Coex mechanism used to make BT have higher priority and more time to
transfer data when BT inquiry-page, which leads to poor WiFi performance.
Should take WiFi traffic into consideration. If the WiFi is having heavy
traffic, use another parameter to make sure WiFi has more chance to TX/RX,
while guarantee the priority of BT for inquiry. If the WiFi isn't busy
(connected or not), set proper parameter to fix originals.
Fixes: f5df1a8b43 ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile")
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529025009.2468-3-yhchuang@realtek.com
Without setting antenna control owner, the WiFi could be disconnected if
the BT has traffic. Because the antenna is switched to BT side for its
traffic, and the WiFi will have no chance to transfer data. Set control
owner to prevent WiFi disconnect issue.
Fixes: f5df1a8b43 ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile")
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529025009.2468-2-yhchuang@realtek.com
When wl12xx_cmd_role_disable() returns an error code,
a pairing runtime PM usage counter decrement is needed to
keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200520130806.14789-1-dinghao.liu@zju.edu.cn
When wlcore_hw_interrupt_notify() returns an error code,
a pairing runtime PM usage counter decrement is needed to
keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200520125724.12832-1-dinghao.liu@zju.edu.cn
pm_runtime_get_sync() increments the runtime PM usage counter even
the call returns an error code. Thus a pairing decrement is needed
on the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200520124649.10848-1-dinghao.liu@zju.edu.cn
There are two error handling paths in this functon. When
wlcore_tx_work_locked() returns an error code, we should
decrease the runtime PM usage counter the same way as the
error handling path beginning from pm_runtime_get_sync().
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200520124241.9931-1-dinghao.liu@zju.edu.cn
Since the driver was first introduced into the kernel, it has only
handled the ciphers associated with WEP, WPA, and WPA2. It fails with
WPA3 even though mac80211 can handle those additional ciphers in software,
b43legacy did not report that it could handle them. By setting MFP_CAPABLE using
ieee80211_set_hw(), the problem is fixed.
With this change, b43legacy will handle the ciphers it knows in hardware,
and let mac80211 handle the others in software. It is not necessary to
use the module parameter NOHWCRYPT to turn hardware encryption off.
Although this change essentially eliminates that module parameter,
I am choosing to keep it for cases where the hardware is broken,
and software encryption is required for all ciphers.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200526155909.5807-3-Larry.Finger@lwfinger.net
Since the driver was first introduced into the kernel, it has only
handled the ciphers associated with WEP, WPA, and WPA2. It fails with
WPA3 even though mac80211 can handle those additional ciphers in software,
b43 did not report that it could handle them. By setting MFP_CAPABLE using
ieee80211_set_hw(), the problem is fixed.
With this change, b43 will handle the ciphers it knows in hardware,
and let mac80211 handle the others in software. It is not necessary to
use the module parameter NOHWCRYPT to turn hardware encryption off.
Although this change essentially eliminates that module parameter,
I am choosing to keep it for cases where the hardware is broken,
and software encryption is required for all ciphers.
Reported-and-tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200526155909.5807-2-Larry.Finger@lwfinger.net
This reverts commit 07d0f55349.
For rtw88 driver, the SDIO is going to be supported, so there is
no need to remove the SDIO related power sequence settings. And
while the power sequence parser will pass in the mask of the HCI,
the SDIO part will not be used to set registers accordingly.
Moreover, the power sequence table is released as a whole package,
so the next time if we are going to update, the SDIO settings will
be overwritten. So, revert this now.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200520055350.23328-1-yhchuang@realtek.com
This gives us WPA3 support out of the box without having to manually disable
hardware crypto. The driver will fall back to software crypto if the connection
requires management frame protection.
Suggested-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200525134906.1672-1-rsalvaterra@gmail.com
All macro names for SDIO device IDs are prefixed by vendor name to which
device ID belongs. So for consistency add Broadcom string vendor prefix to
all Cypress macro names as they belong to SDIO Broadcom vendor ID.
Change also Cypress 43012 value from decimal do hexadecimal notation to be
consistent with all other values.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-11-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Also replace generic MANUFACTURER macros by proper SDIO IDs macros.
Checks for device IDs are slightly modified to use SDIO device IDs.
This allows removal of all custom MANUFACTURER macros from ath10k.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-9-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Also replace generic MANUFACTURER macros by proper SDIO IDs macros.
Check for "AR6003 or later" is slightly modified to use SDIO device IDs.
This allows removal of all custom MANUFACTURER macros from ath6kl.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522144412.19712-8-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add _WLAN suffix to macro names for consistency with other Marvell macros.
These IDs represents wlan function of combo bt/wlan cards. Other functions
of these cards have different IDs.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522144412.19712-4-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Range request version 10 keeps the same command size as version 9
but uses 2 reserved fields for the responder beacon interval and
station id (if exists).
For now, since the beacon interval of unassoc APs is unknown, use
a value of 100 TUs which is a common value for many APs.
While at it, remove the definition for CCMP_256 cipher, since this
is not supported.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200529092401.b7ccdad0805f.I59ea7f773caed85a66c61401066ae169008442e6@changeid
We don't want to have txq code in the PCIe transport code, so move all
the relevant elements to a new iwl_txq structure and store it in
iwl_trans.
spatch
@ replace_pcie @
struct iwl_trans_pcie *trans_pcie;
@@
(
-trans_pcie->queue_stopped
+trans->txqs.queue_stopped
|
-trans_pcie->queue_used
+trans->txqs.queue_used
|
-trans_pcie->txq
+trans->txqs.txq
|
-trans_pcie->txq
+trans->txqs.txq
|
-trans_pcie->cmd_queue
+trans->txqs.cmd.q_id
|
-trans_pcie->cmd_fifo
+trans->txqs.cmd.fifo
|
-trans_pcie->cmd_q_wdg_timeout
+trans->txqs.cmd.wdg_timeout
)
// clean all new unused variables
@ depends on replace_pcie @
type T;
identifier i;
expression E;
@@
- T i = E;
... when != i
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200529092401.a428d3c9d66f.Ie04ae55f33954636a39c98e7ae1e739c0507435b@changeid
Newer firmware versions will parse a few extra bits in the
context info to be able to determine whether we are using
bigger than 4k RBs, indicate 8k/12k to them if we actually
use those (e.g. for sniffer based on the module parameter).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200529092401.f83f994572ca.Ibcfd66c3f9b69e68a53b3b2df8331ffb225db655@changeid
ACPI Device Specific Method (DSM) allows standardized feature
configuration through the ACPI interface without the namespace
pollution of the usual mechanism (ACPI method for each feature).
Add generic function for evaluating DSM objects and function for
evaluating a DSM with no arguments and a single int return value.
also implement the required backport for UUID.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200529092401.c3242ff3ba5c.Icb48c8d61bede5dda7ef267bff10e4798e9dc77b@changeid
Continuous Double "the" in a comment. Changed it to single "the"
Signed-off-by: Hari <harichandrakanthan@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Accordance to the i225 datasheet this register address
used by Host Transmit Discarded Packet by MAC counter
and not by not applicable Carrier Extension Error counter.
This patch comes to fix this wrong definition.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Accordance to the i225 datasheet sequence error counter does not
applicable to the i225 device.
This patch comes to clean up this counter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Receive error counter reflect total number of non-filtered
packets received with errors. This includes: CRC error,
symbol error, Rx data error and carrier extend error.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Accordance to the i225 datasheet symbol error counter does not
applicable to the i225 device.
This patch comes to clean up this counter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the following coccicheck warning:
drivers/net/ethernet/intel/i40e/i40e_adminq.c:699:13-21: Unneeded
variable: "ret_code". Return "0" on line 710
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It's an error if the value of the RX/TX tail descriptor does not match
what was written. The error condition is true regardless the duration
of the interference from ME. But the driver only performs the reset if
E1000_ICH_FWSM_PCIM2PCI_COUNT (2000) iterations of 50us delay have
transpired. The extra condition can lead to inconsistency between the
state of hardware as expected by the driver.
Fix this by dropping the check for number of delay iterations.
While at it, also make __ew32_prepare() static as it's not used
anywhere else.
CC: stable <stable@vger.kernel.org>
Signed-off-by: Punit Agrawal <punit1.agrawal@toshiba.co.jp>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
IGC supports a total of 32 rules. 16 MAC address based, 8 VLAN priority
based, and 8 Ethertype based. This patch fixes IGC_MAX_RXNFC_RULES
accordingly.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The way Rx queue assignment based on mac address, Ethertype and VLAN
priority filtering operates in I225 doesn't allow us to properly support
NFC rules with multiple matches.
Consider the following example which assigns to queue 2 frames matching
the address MACADDR *and* Ethertype ETYPE.
$ ethtool -N eth0 flow-type ether dst <MACADDR> proto <ETYPE> queue 2
When such rule is applied, we have 2 unwanted behaviors:
1) Any frame matching MACADDR will be assigned to queue 2. It
doesn't matter the ETYPE value.
2) Any accepted frame that has Ethertype equals to ETYPE, no matter
the mac address, will be assigned to queue 2 as well.
In current code, multiple-match filters are accepted by the driver, even
though it doesn't support them properly. This patch adds a check for
multiple-match rules in igc_ethtool_is_nfc_rule_valid() so they are
rejected.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Transmit underrun, late and excess collision flags not in use.
This patch comes to clean up these flags.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function always return 0 now, we can make it return void to
simplify the code. This fixes the following coccicheck warning:
drivers/net/ethernet/intel/igb/e1000_mac.c:728:5-12: Unneeded variable:
"ret_val". Return "0" on line 751
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit b5f69ccf67 ("ixgbe: avoid bringing rings up/down as macvlans are added/removed")
left behind this, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the following coccicheck warning:
drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c:105:2-38: WARNING:
Assignment of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
No need to convert '==' expression to bool. This fixes the following
coccicheck warning:
drivers/net/ethernet/intel/ixgbe/ixgbe_common.c:68:11-16: WARNING:
conversion to bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The comment above i40e_run_xdp_zc() was clearly copy-pasted from
function i40e_xsk_umem_setup, which is just above.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When calling hclge_parse_speed() fails, printing out the speed is
helpful for debugging.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some fields in struct hclge_dev which have not been used.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HCLGEVF_CMDQ_INTR_SRC_REG and HCLGEVF_CMDQ_INTR_STS_REG are same
as HCLGEVF_VECTOR0_CMDQ_SRC_REG and HCLGEVF_VECTOR0_CMDQ_STAT_REG,
replace the former with the latter, and rename macro
HCLGEVF_VECTOR0_CMDQ_STAT_REG since 'stat' is not abbreviation of
'state'.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since field .uinfo in struct hnae3_handle never be used,
so remove it and its structure definition.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove HNAE3_RESTORE_CLIENT which is not needed now.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel