The XIVE VP is an internal structure which allow the XIVE interrupt
controller to maintain the interrupt context state of vCPUs non
dispatched on HW threads.
When a guest is started, the XIVE KVM device allocates a block of
XIVE VPs in OPAL, enough to accommodate the highest possible vCPU
id KVM_MAX_VCPU_ID (16384) packed down to KVM_MAX_VCPUS (2048).
With a guest's core stride of 8 and a threading mode of 1 (QEMU's
default), a VM must run at least 256 vCPUs to actually need such a
range of VPs.
A POWER9 system has a limited XIVE VP space : 512k and KVM is
currently wasting this HW resource with large VP allocations,
especially since a typical VM likely runs with a lot less vCPUs.
Make the size of the VP block configurable. Add an nr_servers
field to the XIVE structure and a function to set it for this
purpose.
Split VP allocation out of the device create function. Since the
VP block isn't used before the first vCPU connects to the XIVE KVM
device, allocation is now performed by kvmppc_xive_connect_vcpu().
This gives the opportunity to set nr_servers in between:
kvmppc_xive_create() / kvmppc_xive_native_create()
.
.
kvmppc_xive_set_nr_servers()
.
.
kvmppc_xive_connect_vcpu() / kvmppc_xive_native_connect_vcpu()
The connect_vcpu() functions check that the vCPU id is below nr_servers
and if it is the first vCPU they allocate the VP block. This is protected
against a concurrent update of nr_servers by kvmppc_xive_set_nr_servers()
with the xive->lock mutex.
Also, the block is allocated once for the device lifetime: nr_servers
should stay constant otherwise connect_vcpu() could generate a boggus
VP id and likely crash OPAL. It is thus forbidden to update nr_servers
once the block is allocated.
If the VP allocation fail, return ENOSPC which seems more appropriate to
report the depletion of system wide HW resource than ENOMEM or ENXIO.
A VM using a stride of 8 and 1 thread per core with 32 vCPUs would hence
only need 256 VPs instead of 2048. If the stride is set to match the number
of threads per core, this goes further down to 32.
This will be exposed to userspace by a subsequent patch.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reduce code duplication by consolidating the checking of vCPU ids and VP
ids to a common helper used by both legacy and native XIVE KVM devices.
And explain the magic with a comment.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Testing has revealed the existence of a race condition where a XIVE
interrupt being shut down can be in one of the XIVE interrupt queues
(of which there are up to 8 per CPU, one for each priority) at the
point where free_irq() is called. If this happens, can return an
interrupt number which has been shut down. This can lead to various
symptoms:
- irq_to_desc(irq) can be NULL. In this case, no end-of-interrupt
function gets called, resulting in the CPU's elevated interrupt
priority (numerically lowered CPPR) never gets reset. That then
means that the CPU stops processing interrupts, causing device
timeouts and other errors in various device drivers.
- The irq descriptor or related data structures can be in the process
of being freed as the interrupt code is using them. This typically
leads to crashes due to bad pointer dereferences.
This race is basically what commit 62e0468650 ("genirq: Add optional
hardware synchronization for shutdown", 2019-06-28) is intended to
fix, given a get_irqchip_state() method for the interrupt controller
being used. It works by polling the interrupt controller when an
interrupt is being freed until the controller says it is not pending.
With XIVE, the PQ bits of the interrupt source indicate the state of
the interrupt source, and in particular the P bit goes from 0 to 1 at
the point where the hardware writes an entry into the interrupt queue
that this interrupt is directed towards. Normally, the code will then
process the interrupt and do an end-of-interrupt (EOI) operation which
will reset PQ to 00 (assuming another interrupt hasn't been generated
in the meantime). However, there are situations where the code resets
P even though a queue entry exists (for example, by setting PQ to 01,
which disables the interrupt source), and also situations where the
code leaves P at 1 after removing the queue entry (for example, this
is done for escalation interrupts so they cannot fire again until
they are explicitly re-enabled).
The code already has a 'saved_p' flag for the interrupt source which
indicates that a queue entry exists, although it isn't maintained
consistently. This patch adds a 'stale_p' flag to indicate that
P has been left at 1 after processing a queue entry, and adds code
to set and clear saved_p and stale_p as necessary to maintain a
consistent indication of whether a queue entry may or may not exist.
With this, we can implement xive_get_irqchip_state() by looking at
stale_p, saved_p and the ESB PQ bits for the interrupt.
There is some additional code to handle escalation interrupts
properly; because they are enabled and disabled in KVM assembly code,
which does not have access to the xive_irq_data struct for the
escalation interrupt. Hence, stale_p may be incorrect when the
escalation interrupt is freed in kvmppc_xive_{,native_}cleanup_vcpu().
Fortunately, we can fix it up by looking at vcpu->arch.xive_esc_on,
with some careful attention to barriers in order to ensure the correct
result if xive_esc_irq() races with kvmppc_xive_cleanup_vcpu().
Finally, this adds code to make noise on the console (pr_crit and
WARN_ON(1)) if we find an interrupt queue entry for an interrupt
which does not have a descriptor. While this won't catch the race
reliably, if it does get triggered it will be an indication that
the race is occurring and needs to be debugged.
Fixes: 243e25112d ("powerpc/xive: Native exploitation of the XIVE interrupt controller")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190813100648.GE9567@blackberry
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XICS-on-XIVE KVM device needs to allocate XIVE event queues when a
priority is used by the OS. This is referred as EQ provisioning and it
is done under the hood when :
1. a CPU is hot-plugged in the VM
2. the "set-xive" is called at VM startup
3. sources are restored at VM restore
The kvm->lock mutex is used to protect the different XIVE structures
being modified but in some contexts, kvm->lock is taken under the
vcpu->mutex which is not permitted by the KVM locking rules.
Introduce a new mutex 'lock' for the KVM devices for them to
synchronize accesses to the XIVE device structures.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When a P9 sPAPR VM boots, the CAS negotiation process determines which
interrupt mode to use (XICS legacy or XIVE native) and invokes a
machine reset to activate the chosen mode.
We introduce 'release' methods for the XICS-on-XIVE and the XIVE
native KVM devices which are called when the file descriptor of the
device is closed after the TIMA and ESB pages have been unmapped.
They perform the necessary cleanups : clear the vCPU interrupt
presenters that could be attached and then destroy the device. The
'release' methods replace the 'destroy' methods as 'destroy' is not
called anymore once 'release' is. Compatibility with older QEMU is
nevertheless maintained.
This is not considered as a safe operation as the vCPUs are still
running and could be referencing the KVM device through their
presenters. To protect the system from any breakage, the kvmppc_xive
objects representing both KVM devices are now stored in an array under
the VM. Allocation is performed on first usage and memory is freed
only when the VM exits.
[paulus@ozlabs.org - Moved freeing of xive structures to book3s.c,
put it under #ifdef CONFIG_KVM_XICS.]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The KVM XICS-over-XIVE device and the proposed KVM XIVE native device
implement an IRQ space for the guest using the generic IPI interrupts
of the XIVE IC controller. These interrupts are allocated at the OPAL
level and "mapped" into the guest IRQ number space in the range 0-0x1FFF.
Interrupt management is performed in the XIVE way: using loads and
stores on the addresses of the XIVE IPI interrupt ESB pages.
Both KVM devices share the same internal structure caching information
on the interrupts, among which the xive_irq_data struct containing the
addresses of the IPI ESB pages and an extra one in case of pass-through.
The later contains the addresses of the ESB pages of the underlying HW
controller interrupts, PHB4 in all cases for now.
A guest, when running in the XICS legacy interrupt mode, lets the KVM
XICS-over-XIVE device "handle" interrupt management, that is to
perform the loads and stores on the addresses of the ESB pages of the
guest interrupts. However, when running in XIVE native exploitation
mode, the KVM XIVE native device exposes the interrupt ESB pages to
the guest and lets the guest perform directly the loads and stores.
The VMA exposing the ESB pages make use of a custom VM fault handler
which role is to populate the VMA with appropriate pages. When a fault
occurs, the guest IRQ number is deduced from the offset, and the ESB
pages of associated XIVE IPI interrupt are inserted in the VMA (using
the internal structure caching information on the interrupts).
Supporting device passthrough in the guest running in XIVE native
exploitation mode adds some extra refinements because the ESB pages
of a different HW controller (PHB4) need to be exposed to the guest
along with the initial IPI ESB pages of the XIVE IC controller. But
the overall mechanic is the same.
When the device HW irqs are mapped into or unmapped from the guest
IRQ number space, the passthru_irq helpers, kvmppc_xive_set_mapped()
and kvmppc_xive_clr_mapped(), are called to record or clear the
passthrough interrupt information and to perform the switch.
The approach taken by this patch is to clear the ESB pages of the
guest IRQ number being mapped and let the VM fault handler repopulate.
The handler will insert the ESB page corresponding to the HW interrupt
of the device being passed-through or the initial IPI ESB page if the
device is being removed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
These controls will be used by the H_INT_SET_QUEUE_CONFIG and
H_INT_GET_QUEUE_CONFIG hcalls from QEMU to configure the underlying
Event Queue in the XIVE IC. They will also be used to restore the
configuration of the XIVE EQs and to capture the internal run-time
state of the EQs. Both 'get' and 'set' rely on an OPAL call to access
the EQ toggle bit and EQ index which are updated by the XIVE IC when
event notifications are enqueued in the EQ.
The value of the guest physical address of the event queue is saved in
the XIVE internal xive_q structure for later use. That is when
migration needs to mark the EQ pages dirty to capture a consistent
memory state of the VM.
To be noted that H_INT_SET_QUEUE_CONFIG does not require the extra
OPAL call setting the EQ toggle bit and EQ index to configure the EQ,
but restoring the EQ state will.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This control will be used by the H_INT_SET_SOURCE_CONFIG hcall from
QEMU to configure the target of a source and also to restore the
configuration of a source when migrating the VM.
The XIVE source interrupt structure is extended with the value of the
Effective Interrupt Source Number. The EISN is the interrupt number
pushed in the event queue that the guest OS will use to dispatch
events internally. Caching the EISN value in KVM eases the test when
checking if a reconfiguration is indeed needed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The XIVE KVM device maintains a list of interrupt sources for the VM
which are allocated in the pool of generic interrupts (IPIs) of the
main XIVE IC controller. These are used for the CPU IPIs as well as
for virtual device interrupts. The IRQ number space is defined by
QEMU.
The XIVE device reuses the source structures of the XICS-on-XIVE
device for the source blocks (2-level tree) and for the source
interrupts. Under XIVE native, the source interrupt caches mostly
configuration information and is less used than under the XICS-on-XIVE
device in which hcalls are still necessary at run-time.
When a source is initialized in KVM, an IPI interrupt source is simply
allocated at the OPAL level and then MASKED. KVM only needs to know
about its type: LSI or MSI.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The user interface exposes a new capability KVM_CAP_PPC_IRQ_XIVE to
let QEMU connect the vCPU presenters to the XIVE KVM device if
required. The capability is not advertised for now as the full support
for the XIVE native exploitation mode is not yet available. When this
is case, the capability will be advertised on PowerNV Hypervisors
only. Nested guests (pseries KVM Hypervisor) are not supported.
Internally, the interface to the new KVM device is protected with a
new interrupt mode: KVMPPC_IRQ_XIVE.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
That feature, provided by Power9 DD2.0 and later, when supported
by newer OPAL versions, allows us to sacrifice a queue (priority 7)
in favor of merging all the escalation interrupts of the queues
of a single VP into a single interrupt.
This reduces the number of host interrupts used up by KVM guests
especially when those guests use multiple priorities.
It will also enable a future change to control the masking of the
escalation interrupts more precisely to avoid spurious ones.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
In KVM's XICS-on-XIVE emulation, kvmppc_xive_get_xive() returns the
value of state->guest_server as "server". However, this value is not
set by it's counterpart kvmppc_xive_set_xive(). When the guest uses
this interface to migrate interrupts away from a CPU that is going
offline, it sees all interrupts as belonging to CPU 0, so they are
left assigned to (now) offline CPUs.
This patch removes the guest_server field from the state, and returns
act_server in it's place (that is, the CPU actually handling the
interrupt, which may differ from the one requested).
Fixes: 5af5099385 ("KVM: PPC: Book3S HV: Native usage of the XIVE interrupt controller")
Cc: stable@vger.kernel.org
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
This patch makes KVM capable of using the XIVE interrupt controller
to provide the standard PAPR "XICS" style hypercalls. It is necessary
for proper operations when the host uses XIVE natively.
This has been lightly tested on an actual system, including PCI
pass-through with a TG3 device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Cleanup pr_xxx(), unsplit pr_xxx() strings, etc., fix build
failures by adding KVM_XIVE which depends on KVM_XICS and XIVE, and
adding empty stubs for the kvm_xive_xxx() routines, fixup subject,
integrate fixes from Paul for building PR=y HV=n]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Greg Kurz