For PUNIT device, ISPDRIVER_IPC and GTDDRIVER_IPC resources are not
mandatory. So when PMC IPC driver creates a PUNIT device, if these
resources are not available then it creates dummy resource entries for
these missing resources. But during PUNIT device probe, doing ioremap on
these dummy resources generates following warning messages.
intel_punit_ipc: can't request region for resource [mem 0x00000000]
intel_punit_ipc: can't request region for resource [mem 0x00000000]
intel_punit_ipc: can't request region for resource [mem 0x00000000]
intel_punit_ipc: can't request region for resource [mem 0x00000000]
This patch fixes this issue by adding extra check for resource size
before performing ioremap operation.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Variable byte_data is being initialized and re-assigned with values that
are never read. Remove these as these redundant assignments. Cleans up
clang warning:
drivers/platform/x86/dell-smo8800.c:106:2: warning: Value stored to 'byte_data'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Commit f9cf3b2880 ("platform/x86: hp-wmi: Refactor dock and tablet
state fetchers") consolidated the methods for docking and laptop mode
detection, but omitted to apply the correct mask for the laptop mode
(it always uses the constant for docking).
Fixes: f9cf3b2880 ("platform/x86: hp-wmi: Refactor dock and tablet state fetchers")
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Moves timer structure off stack and
into struct ips_driver.
Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andy@infradead.org>
Cc: platform-driver-x86@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The local variable "err" will eventually be set to an appropriate value
a bit later. Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Source code review for a specific software refactoring showed the need
for another correction because the error code "-1" was returned so far
if a call of the function "sony_call_snc_handle" failed here.
Thus assign the return value from these two function calls also to
the variable "err" and provide it in case of a failure.
Fixes: d6f15ed876 ("sony-laptop: use soft rfkill status stored in hw")
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lkml.org/lkml/2017/10/31/463
Link: https://lkml.kernel.org/r/<CAHp75VcMkXCioCzmLE0+BTmkqc5RSOx9yPO0ectVHMrMvewgwg@mail.gmail.com>
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
It's important for the driver to provide a R/W ioctl to ensure that
two competing userspace processes don't race to provide or read each
others data.
This userspace character device will be used to perform SMBIOS calls
from any applications.
It provides an ioctl that will allow passing the WMI calling
interface buffer between userspace and kernel space.
This character device is intended to deprecate the dcdbas kernel module
and the interface that it provides to userspace.
To perform an SMBIOS IOCTL call using the character device userspace will
perform a read() on the the character device. The WMI bus will provide
a u64 variable containing the necessary size of the IOCTL buffer.
The API for interacting with this interface is defined in documentation
as well as the WMI uapi header provides the format of the structures.
Not all userspace requests will be accepted. The dell-smbios filtering
functionality will be used to prevent access to certain tokens and calls.
All whitelisted commands and tokens are now shared out to userspace so
applications don't need to define them in their own headers.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
For WMI operations that are only Set or Query readable and writable sysfs
attributes created by WMI vendor drivers or the bus driver makes sense.
For other WMI operations that are run on Method, there needs to be a
way to guarantee to userspace that the results from the method call
belong to the data request to the method call. Sysfs attributes don't
work well in this scenario because two userspace processes may be
competing at reading/writing an attribute and step on each other's
data.
When a WMI vendor driver declares a callback method in the wmi_driver
the WMI bus driver will create a character device that maps to that
function. This callback method will be responsible for filtering
invalid requests and performing the actual call.
That character device will correspond to this path:
/dev/wmi/$driver
Performing read() on this character device will provide the size
of the buffer that the character device needs to perform calls.
This buffer size can be set by vendor drivers through a new symbol
or when MOF parsing is available by the MOF.
Performing ioctl() on this character device will be interpretd
by the WMI bus driver. It will perform sanity tests for size of
data, test them for a valid instance, copy the data from userspace
and pass iton to the vendor driver to further process and run.
This creates an implicit policy that each driver will only be allowed
a single character device. If a module matches multiple GUID's,
the wmi_devices will need to be all handled by the same wmi_driver.
The WMI vendor drivers will be responsible for managing inappropriate
access to this character device and proper locking on data used by
it.
When a WMI vendor driver is unloaded the WMI bus driver will clean
up the character device and any memory allocated for the call.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
When a userspace interface is introduced to dell-smbios filtering
support will be used to make sure that userspace doesn't make calls
deemed unsafe or that can cause the kernel drivers to get out of
sync.
A blacklist is provided for the following:
- Items that are in use by other kernel drivers
- Items that are deemed unsafe (diagnostics, write-once, etc)
- Any items in the blacklist will be rejected.
Following that a whitelist is provided as follows:
- Each item has an associated capability. If a userspace interface
accesses this item, that capability will be tested to filter
the request.
- If the process provides CAP_SYS_RAWIO the whitelist will be
overridden.
When an item is not in the blacklist, or whitelist and the process
is run with insufficient capabilities the call will be rejected.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
WSMT is as an attestation to the OS that the platform won't
modify memory outside of pre-defined areas.
If a platform has WSMT enabled in BIOS setup, SMM calls through
dcdbas will fail. The only way to access platform data in these
instances is through the WMI SMBIOS calling interface.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
The dell-smbios stack only currently uses an SMI interface which grants
direct access to physical memory to the firmware SMM methods via a pointer.
This dispatcher driver adds a WMI-ACPI interface that is detected by WMI
probe and preferred over the SMI interface in dell-smbios.
Changing this to operate over WMI-ACPI will use an ACPI OperationRegion
for a buffer of data storage when SMM calls are performed.
This is a safer approach to use in kernel drivers as the SMM will
only have access to that OperationRegion.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
This splits up the dell-smbios driver into two drivers:
* dell-smbios
* dell-smbios-smm
dell-smbios can operate with multiple different dispatcher drivers to
perform SMBIOS operations.
Also modify the interface that dell-laptop and dell-wmi use align to this
model more closely. Rather than a single global buffer being allocated
for all drivers, each driver will allocate and be responsible for it's own
buffer. The pointer will be passed to the calling function and each
dispatcher driver will then internally copy it to the proper location to
perform it's call.
Add defines for calls used by these methods in the dell-smbios.h header
for tracking purposes.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Currently userspace tools can access system tokens via the dcdbas
kernel module and a SMI call that will cause the platform to execute
SMM code.
With a goal in mind of deprecating the dcdbas kernel module a different
method for accessing these tokens from userspace needs to be created.
This is intentionally marked to only be readable as a process with
CAP_SYS_ADMIN as it can contain sensitive information about the
platform's configuration.
While adding this interface I found that some tokens are duplicated.
These need to be ignored from sysfs to avoid duplicate files.
MAINTAINERS was missing for this driver. Add myself and Pali to
maintainers list for it.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
The proper way to indicate that a system is a 'supported' Dell System
is by the presence of this string in OEM strings.
Allowing the driver to load on non-Dell systems will have undefined
results.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
The only driver using this was dell-wmi, and it really was a hack.
The driver was getting a data attribute from another driver and this
type of action should not be encouraged.
Rather drivers that need to interact with one another should pass
data back and forth via exported functions.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
All communication on individual GUIDs should occur in separate drivers.
Allowing a driver to communicate with the bus to another GUID is just
a hack that discourages drivers to adopt the bus model.
The information found from the WMI descriptor driver is now exported
for use by other drivers.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
This is intended to be variable and provided by the platform.
Some platforms this year will be adopting a 32k WMI buffer, so don't
complain when encountering those platforms or any other future changes.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Some cases the wrong type was used for errors and checks can be
done more cleanly.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
There is a lot of error checking in place for the format of the WMI
descriptor buffer, but some of the potentially raised issues should
be considered critical failures.
If the buffer size or header don't match, this is a good indication
that the buffer format changed in a way that the rest of the data
should not be relied upon.
For the remaining data set vectors, continue to notate a warning
in undefined results, but as those are fields that the descriptor
intended to refer to other applications, don't fail if they're new
values.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Drivers properly using the wmibus can pass their wmi_device
pointer rather than the GUID back to the WMI bus to evaluate
the proper methods.
Any "new" drivers added that use the WMI bus should use this
rather than the old wmi_evaluate_method that would take the
GUID.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Later on these structures will be brought up to userspace.
the word "class" is a reserved word in c++ and this will prevent
uapi headers from being included directly in c++ programs.
To make life easier on these applications, prepare the change now.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Edward O'Callaghan <quasisec@google.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
The fusb302 driver as merged in staging uses "typec_fusb302" as i2c-id
rather then just "fusb302" and needs us to set a number of device-
properties, adjust the intel_cht_int33fe driver accordingly.
One of the properties set is max-snk-mv which makes the fusb302 driver
negotiate up to 12V charging voltage, which is a bad idea on boards
which are not setup to handle this, so this commit also adds 2 extra
sanity checks to make sure that the expected Whiskey Cove PMIC +
TI bq24292i charger combo, which can handle 12V, is present.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add touchscreen platform data for the Digma e200 tablet.
Signed-off-by: Sergey Tshovrebov <sinxwal@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The GP-electronic T701 has its LCD panel mounted upside-down, initially
my plan was to fix this by transparently rotating the image in the i915
driver (my "drm/i915: Deal with upside-down mounted LCD" patch), but
that approach has been rejected instead the kernel will now export
a "panel orientation" property on the drm-connector for the panel and
let userspace deal with it.
But userspace expects the touchscreen coordinates to match the panel
coordinates *before* applying any rotation, so now that we no longer hide
the upside-down-ness of the LCD panel from userspace the coordinates being
generated are wrong and we need to apply a rotation of 180 degrees to the
coordinates to fix this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
peaq_wmi_exit will only ever get called if peaq_wmi_init succeeds, so
there is no need to repeat the checks from peaq_wmi_init.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Lenovo Yoga 920-13IKB does not have a hw rfkill switch, and trying
to read the hw rfkill switch through the ideapad module causes it to
always report as blocked.
This commit adds the Lenovo Yoga 920-13IKB to the no_hw_rfkill dmi list,
fixing the WiFI breakage.
Signed-off-by: Philipp Hug <philipp@hug.cx>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Several function prototypes for the set/get functions defined by
module_param_call() have a slightly wrong argument types. This fixes
those in an effort to clean up the calls when running under type-enforced
compiler instrumentation for CFI. This is the result of running the
following semantic patch:
@match_module_param_call_function@
declarer name module_param_call;
identifier _name, _set_func, _get_func;
expression _arg, _mode;
@@
module_param_call(_name, _set_func, _get_func, _arg, _mode);
@fix_set_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._set_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _set_func(
-_val_type _val
+const char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
@fix_get_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._get_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _get_func(
-_val_type _val
+char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
Two additional by-hand changes are included for places where the above
Coccinelle script didn't notice them:
drivers/platform/x86/thinkpad_acpi.c
fs/lockd/svc.c
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Radio LED detection method implemented in commit 4f62568c1f
("fujitsu-laptop: Support radio LED") turned out to be incorrect as it
causes a radio LED to be erroneously detected on a Fujitsu Lifebook E751
which has a slide switch (and thus no radio LED). Use bit 17 of
flags_supported (the value returned by method S000 of ACPI device
FUJ02E3) to determine whether a radio LED is present as it seems to be a
more reliable indicator, based on comparing DSDT tables of four Fujitsu
Lifebook models (E744, E751, S7110, S8420).
Fixes: 4f62568c1f ("fujitsu-laptop: Support radio LED")
Reported-by: Heinrich Siebmanns <harv@gmx.de>
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Heinrich Siebmanns <harv@gmx.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Added support for HP ProBook 440 G4 laptops by including the accelerometer
orientation quirk for that device. Testing was performed based on the
axis orientation guidelines here:
https://www.kernel.org/doc/Documentation/misc-devices/lis3lv02d
which states "If the left side is elevated, X increases (becomes positive)".
When tested, on lifting the left edge, x values became increasingly negative
thus indicating an inverted x-axis on the installed lis3lv02d chip.
This was compensated by adding an entry for this device in hp_accel.c
specifying the quirk as x_inverted. The patch was tested on a
ProBook 440 G4 device and x-axis as well as y and z-axis values are now
generated as per spec.
Signed-off-by: Osama Khan <osama.khan@ericsson.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Ev Kontsevoy reported that he can't see the presence of
"/proc/sys/kernel/sched_itmt_enabled" on i9-7900x with Asrock x299
Taichi system even if he enabled "Turbo 3.0" in the BIOS.
The problem is that even if one core max is 200MHz more than others, the
current implementation couldn't enumerate that with the way the system
is configured.
The system by default configured for legacy mode (no HWP or speed shift
technology), in this mode only way we can enumerate via the mail box
interface as implemented in this driver. We were planing to only use
this driver for Broadwell, but we need to extend this because some
Skylake system has same issue as Braodwell systems.
On this system BIOS allows to change to HWP mode, where we expect that
we can enumerate favored core with ACPI-CPPC. But on this system the
core priority is 0xff for all cores in CPPC object. So this is not an
option.
Hence this change allows Skylake systems to be enumerate favored core
similar to Broadwell in legacy mode.
Reported-and-tested-by: Ev Kontsevoy <ev@kontsevoy.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
'default n' is a default behaviour of Kconfig options. So, remove
explicit line from Kconfig.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
linux/io.h defines readq() and ioremap_nocache() / iounmap() functions.
If not included, the build fails:
intel_telemetry_pltdrv.c:1165:31: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
intel_telemetry_pltdrv.c:1165:33: error: implicit declaration of function 'ioremap_nocache' [-Werror=implicit-function-declaration]
intel_telemetry_pltdrv.c:1202:3: error: implicit declaration of function 'iounmap' [-Werror=implicit-function-declaration]
intel_telemetry_pltdrv.c:900:20: error: implicit declaration of function 'readq' [-Werror=implicit-function-declaration]
Fix this by including linux/io.h.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Currently, update_no_reboot_bit() function implemented in this driver
uses mutex_lock() to protect its register updates. But this function is
called with in atomic context in iTCO_wdt_start() and iTCO_wdt_stop()
functions in iTCO_wdt.c driver, which in turn causes "sleeping into
atomic context" issue. This patch fixes this issue by replacing the
mutex_lock() with spin_lock() to protect the GCR read/write/update APIs.
Fixes: 9d855d4 ("platform/x86: intel_pmc_ipc: Fix iTCO_wdt GCS memory mapping failure")
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kupuswamy@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Currently, update_no_reboot_bit() function implemented in this driver
uses mutex_lock() to protect its register updates. But this function is
called with in atomic context in iTCO_wdt_start() and iTCO_wdt_stop()
functions in iTCO_wdt.c driver, which in turn causes "sleeping into
atomic context" issue. This patch fixes this issue by replacing the
mutex_lock() with spin_lock() to protect the GCR read/write/update APIs.
Fixes: 9d855d4 ("platform/x86: intel_pmc_ipc: Fix iTCO_wdt GCS memory mapping failure")
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kupuswamy@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This patch cleans up unnecessary free/alloc calls in ipc_plat_probe(),
ipc_pci_probe() and ipc_plat_get_res() functions by using devm_*
calls.
This patch also adds proper error handling for failure cases in
ipc_pci_probe() function.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
[andy: fixed style issues, missed devm_free_irq(), removed unnecessary log message]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Removes unnecessary header files included in the driver and sorts the
remaining ones in the alphabetical order.
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Telemetry word is misspelled several times in this file as Telemtry. This
fixes the spelling mistake and folds in another minor typo.
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Intel Telemetry driver depends on IPC1 interface. If IPC1 interface is
disabled on a given platform by the system firmware, the driver does not
load but prints misleading information in the dmesg logs.
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The functions cht_int33fe_check_for_max17047 and cht_int33fe_find_max17047
are local to the source and do not need to be in global scope, so make
them static.
Cleans up sparse warnings:
symbol 'cht_int33fe_check_for_max17047' was not declared. Should it be
static?
symbol 'cht_int33fe_find_max17047' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The structures mlxplat_dev and mlxplat_hotplug are local to the source
and do not need to be in global scope, so make them static.
Cleans up sparse warnings:
symbol 'mlxplat_dev' was not declared. Should it be static?
symbol 'mlxplat_hotplug' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Add touchscreen platform data for the Chuwi Hi8 Pro tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
This patch fixes some spelling typos found in Kconfig files.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch removes the FSF address from the GPL notice to fix a
checkpatch.pl CHECK message.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There are fields in the struct ips_mcp_limits which are not used
anywhere and a label which we may get rid of.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Use devm_ and pcim_ functions to make error handling
simpler and code smaller and tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
It seems that the WMI GUID used by the PEAQ 2-in-1 WMI hotkeys is not
as unique as a GUID should be and is used on some other devices too.
This is causing spurious key-press reports on these other devices.
This commits adds a DMI check to the PEAQ 2-in-1 WMI hotkeys driver to
ensure that it is actually running on a PEAQ 2-in-1, fixing the
spurious key-presses on these other devices.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1497861
BugLink: https://bugzilla.suse.com/attachment.cgi?id=743182
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
peaq-wmi on Lenovo ideapad 700-15ISK keeps sending KEY_SOUND,
which makes user's repeated keys gets interrupted.
The system does not have Dolby button, let's blacklist it.
BugLink: https://bugs.launchpad.net/bugs/1720219
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This patch cleans up unnecessary free/alloc calls in ipc_plat_probe(),
ipc_pci_probe() and ipc_plat_get_res() functions by using devm_*
calls.
This patch also adds proper error handling for failure cases in
ipc_pci_probe() function.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
[andy: fixed style issues, missed devm_free_irq(), removed unnecessary log message]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Many thinkpad laptops and convertibles provide the GMMS method to
resolve how far the laptop has been opened and whether it has been
converted into tablet mode. This allows reporting a more precise tablet
mode state to userspace.
The current implementation only reports a summarized tablet mode state
which is triggered as soon as the input devices become unusable as they
are folded away from the display.
This will work on all models where the CMMD method was used previously and
it may also work in other cases.
Thanks to Peter Zhang of Lenovo for providing information on how to use the
GMMS method to query the tablet mode.
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Cc: Peter FP1 Zhang <zhangfp1@lenovo.com>
Cc: Lyude Paul <lyude@redhat.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
My Fujitsu-Siemens Lifebook S6120 doesn't have the FUJ02E3 device,
but it does have FUJ02B1. That means we do register the backlight
device (and it even seems to work), but the code will oops as soon
as we try to set the backlight brightness because it's trying to
call call_fext_func() with a NULL device. Let's just skip those
function calls when the FUJ02E3 device is not present.
Cc: Jonathan Woithe <jwoithe@just42.net>
Cc: Andy Shevchenko <andy@infradead.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # 4.13.x
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
device_create documentation says to cleanup using device_destroy
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
The initialize routine is:
* class -> bus -> platform
The exit routine is:
* platform -> class -> bus
Fix the exit routine to be:
* platform -> bus -> class
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
The include list is randomly assembled right now. Sort in alphabetical
order.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
pr_fmt provides formatting to be used by the driver when
displaying errors and messages.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Pali Pohar <pali.rohar@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
The descriptor GUID is not used to indicate that WMI notifications
in the dell-wmi driver work properly. As such a modalias should
not be present that causes this driver to load on systems with this
GUID.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Pali Pohar <pali.rohar@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
This driver serves the purpose of responding to WMI based notifications
from the DELL_EVENT_GUID (9DBB5994-A997-11DA-B012-B622A1EF5492).
Other GUIDs will be handled by separate drivers.
Update the language used by this driver to avoid future confusion.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Some Asus laptops (ROG series for example) are provided with a lightbar
behind the monitor. This patch make possible to switch it on and off.
This lightbar works exactly like any other led.
Signed-off-by: Maxime Bellengé <maxime.bellenge@gmail.com>
[dvhart: fix commit message format and variable declaration order]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
My Fujitsu-Siemens Lifebook S6120 doesn't have the FUJ02E3 device,
but it does have FUJ02B1. That means we do register the backlight
device (and it even seems to work), but the code will oops as soon
as we try to set the backlight brightness because it's trying to
call call_fext_func() with a NULL device. Let's just skip those
function calls when the FUJ02E3 device is not present.
Cc: Jonathan Woithe <jwoithe@just42.net>
Cc: Andy Shevchenko <andy@infradead.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # 4.13.x
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Note there is a misc driver drop in here given we have support
in IIO and the feeling is no one will care.
A large part of this series is a boiler plate removal series avoiding
the need to explicitly provide THIS_MODULE in various locations.
It's very dull but touches all drivers.
New device support
* ad5446
- add ids to support compatible parts DAC081S101, DAC101S101,
DAC121S101.
- add the dac7512 id and drop the misc driver as feeling is no
one is using it (was introduced for a board that is long obsolete)
* mt6577
- add bindings for mt2712 which is fully compatible with other
supported parts.
* st_pressure
- add support for LPS33HW and LPS35HW with bindings (ids mostly).
New features
* ccs811
- Add support for the data ready trigger.
* mma8452
- remove artifical restriction on supporting multiple event types
at the same time.
* tcs3472
- support out of threshold events
Core and tree wide cleanup
* Use macro magic to remove the need to provide THIS_MODULE as part of
struct iio_info or struct iio_trigger_ops. This is similar to
work done in a number of other subsystems (e.g. i2c, spi).
All drivers are fixed and then the fields in these structures are
removed.
This will cause build failures for out of tree drivers and any
new drivers that cross with this work going into the kernel.
Note mostly done with a coccinelle patch, included in the series
on the mailing list but not merged as the fields no longer exist
in the structures so the any hold outs will cause a build failure.
Cleanups
* ads1015
- avoid writing config register when it doesn't change.
- add 10% to conversion wait time as it seems it is sometimes
a little small.
* ade7753
- replace use of core mlock with a local lock. This is part of a
long term effort to make the use of mlock opaque and single
purpose.
* ade7759
- expand the use of buf_lock to cover previous mlock cases. This
is a slightly nicer solution to the same issue as in ade7753.
* cros_ec
- drop an unused variable
* inv_mpu6050
- add a missing break in a switch for consistency - not actual
bug,
- make some local arrays static to save on object code size.
* max5481
- drop manual setting of the spi module owner as handled by the
spi core.
* max5487
- drop manual setting of the spi module owner as handled by the
spi core.
* max9611
- drop explicit setting of the i2c module owner as handled by
the i2c core.
* mcp320x
- speed up reads on single channel devices,
- drop unused of_device_id data elements,
- document the struct mcp320x,
- improve binding docs to reflect restrictions on spi setup and
to make it explicit that the reference regulator is needed.
* mma8452
- symbolic to octal permissions,
- unsigned to unsigned int.
* st_lsm6dsx
- avoid setting odr values multiple times,
- drop config of LIR as it is only ever set to the existing
defaults,
- drop rounding configuration as it only ever matches the defaults.
* ti-ads8688
- drop manual setting of the spi module owner as handled by the
spi core.
* tsl2x7x
- constify the i2c_device_id,
- cleanup limit checks to avoid static checker warnings (and generally
have nicer code).
-----BEGIN PGP SIGNATURE-----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=ik5C
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.15a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Round one of new device support, features and cleanup for IIO in the 4.15 cycle.
Note there is a misc driver drop in here given we have support
in IIO and the feeling is no one will care.
A large part of this series is a boiler plate removal series avoiding
the need to explicitly provide THIS_MODULE in various locations.
It's very dull but touches all drivers.
New device support
* ad5446
- add ids to support compatible parts DAC081S101, DAC101S101,
DAC121S101.
- add the dac7512 id and drop the misc driver as feeling is no
one is using it (was introduced for a board that is long obsolete)
* mt6577
- add bindings for mt2712 which is fully compatible with other
supported parts.
* st_pressure
- add support for LPS33HW and LPS35HW with bindings (ids mostly).
New features
* ccs811
- Add support for the data ready trigger.
* mma8452
- remove artifical restriction on supporting multiple event types
at the same time.
* tcs3472
- support out of threshold events
Core and tree wide cleanup
* Use macro magic to remove the need to provide THIS_MODULE as part of
struct iio_info or struct iio_trigger_ops. This is similar to
work done in a number of other subsystems (e.g. i2c, spi).
All drivers are fixed and then the fields in these structures are
removed.
This will cause build failures for out of tree drivers and any
new drivers that cross with this work going into the kernel.
Note mostly done with a coccinelle patch, included in the series
on the mailing list but not merged as the fields no longer exist
in the structures so the any hold outs will cause a build failure.
Cleanups
* ads1015
- avoid writing config register when it doesn't change.
- add 10% to conversion wait time as it seems it is sometimes
a little small.
* ade7753
- replace use of core mlock with a local lock. This is part of a
long term effort to make the use of mlock opaque and single
purpose.
* ade7759
- expand the use of buf_lock to cover previous mlock cases. This
is a slightly nicer solution to the same issue as in ade7753.
* cros_ec
- drop an unused variable
* inv_mpu6050
- add a missing break in a switch for consistency - not actual
bug,
- make some local arrays static to save on object code size.
* max5481
- drop manual setting of the spi module owner as handled by the
spi core.
* max5487
- drop manual setting of the spi module owner as handled by the
spi core.
* max9611
- drop explicit setting of the i2c module owner as handled by
the i2c core.
* mcp320x
- speed up reads on single channel devices,
- drop unused of_device_id data elements,
- document the struct mcp320x,
- improve binding docs to reflect restrictions on spi setup and
to make it explicit that the reference regulator is needed.
* mma8452
- symbolic to octal permissions,
- unsigned to unsigned int.
* st_lsm6dsx
- avoid setting odr values multiple times,
- drop config of LIR as it is only ever set to the existing
defaults,
- drop rounding configuration as it only ever matches the defaults.
* ti-ads8688
- drop manual setting of the spi module owner as handled by the
spi core.
* tsl2x7x
- constify the i2c_device_id,
- cleanup limit checks to avoid static checker warnings (and generally
have nicer code).
On Dell Latitude 7275 the 5-button array is not exposed in the ACPI
tables, but notififies are still sent to the Intel HID device object
(device ID INT33D5) in response to power button actions. They were
ignored as the intel-hid driver was not prepared to take care of them
until recently.
Power button wakeup from suspend-to-idle was added in:
commit 635173a17b ("intel-hid: Wake up Dell Latitude 7275 from suspend-to-idle")
However power button suspend doesn't work yet on this platform so it
would be good to add it also.
On the affected platform (for which priv->array is NULL), add a new
upfront check against the power button press notification (0xCE) to
notify_handler(), outside the wakeup mode this time, which allows
reporting the power button press event and triggers the suspend. Also
catch and ignore the corresponding power button release notification
(0xCF) to stop it from being reported as an "unknown event" in the logs.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196115
Tested-by: Jérôme de Bretagne <jerome.debretagne@gmail.com>
Signed-off-by: Jérôme de Bretagne <jerome.debretagne@gmail.com>
Acked-By: Mario Limonciello <mario.limonciello@dell.com>
[dvhart: minor coding style and commit message format fix]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
These were raised by Lukas Wunner as potential DOS attacks against
the system log by passing bad data to sysfs.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Use the standard ARRAY_SIZE() macro instead of the custom
TELEM_EVT_LEN().
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
At least one BIOS enumerates the max17047 both through the INT33FE ACPI
device (it is right there in the resources table) as well as through a
separate MAX17047 device.
This commit checks for the max17047 already being enumerated through
a separate MAX17047 ACPI device and if so it uses the i2c-client
instantiated for this and attaches the device-props for the max17047 to
that i2c-client.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Current implementations of Intel Thunderbolt controllers will go
into a low power mode when not in use.
Many machines containing these controllers also have a GPIO wired up
that can force the controller awake. This is offered via a ACPI-WMI
interface intended to be manipulated by a userspace utility.
This mechanism is provided by Intel to OEMs to include in BIOS.
It uses an industry wide GUID that is populated in a separate _WDG
entry with no binary MOF.
This interface allows software such as fwupd to wake up thunderbolt
controllers to query the firmware version or flash new firmware.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
[andy fixed merge conflicts and bump kernel version for ABI]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Several fixes from static analysis and message noise reduction. Correct
WMI core and related drivers to evaluate instance number 0x0 in
accordance with the documentation. Add intel-telemetry support for
Gemini Lake. Various individual driver fixes noted below.
Two commits appear here which were previously merged during the 4.13 RC
cycle:
- baa5480b05 platform/x86: dell-wmi: Fix driver interface version query
- c801603e6d platform/x86: intel-vbtn: match power button on press rather than release
dell-wmi:
- Update dell_wmi_check_descriptor_buffer() to new model
intel-vbtn:
- reduce unnecessary messages for normal users
- match power button on press rather than release
intel-hid:
- reduce unnecessary messages for normal users
thinkpad_acpi:
- Fix warning about deprecated hwmon_device_register
wmi:
- Fix check for method instance number
ideapad-laptop:
- Expose conservation mode switch
intel_pmc_core:
- Make the driver PCH family agnostic
peaq-wmi:
- Evaluate wmi method with instance number 0x0
- silence a static checker warning
mxm-wmi:
- Evaluate wmi method with instance number 0x0
asus-wmi:
- Evaluate wmi method with instance number 0x0
intel_scu_ipc:
- make intel_scu_ipc_pdata_t const
intel_mid_powerbtn:
- make mid_pb_ddata const
- fix error return code in mid_pb_probe()
hp-wmi:
- Remove unused macro helper
- Correctly determine method id in WMI calls
dell-wmi:
- Fix driver interface version query
intel_telemetry:
- remove redundant macro definition
- Add GLK PSS Event Table
alienware-wmi:
- fix format string overflow warning
ibm_rtl:
- remove unnecessary static in ibm_rtl_write()
msi-wmi:
- remove unnecessary static in msi_wmi_notify()
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZsvdiAAoJEKbMaAwKp364V+UIAI27WP1MKQ6zKiXAt6TTLQww
RGbeTrgxsHwxIp1ioo3MZtRa4uTMrJ/A/Es7nzZBSAAp8qPLOCaZYGtsH0tYkzcc
zGLw+q5EBEjiMiq8WvkgD+NLq6icdsB0MUuuh06y34/LWiOwpp9wNemszHO9Vo2/
vc5PkgNmMx5K4zJvl6A3JAY98XlXxG65vYMrsIL17EFwZjuixrcCjDY86HKxEnNV
tmfJ1Mhiu5HnDniCgRubdRBo4LwAeRdrXXkrsTZip+4RuXvm0gvxHujwgllIY4Ns
m6xFXQApaGtXxd9vcSBHXE7whTgWrb7yPhUQzgt/Dd3E6ywF2THfn5jvwJUEflc=
=LuAp
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.14-1' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Several fixes from static analysis and message noise reduction.
Correct WMI core and related drivers to evaluate instance number 0x0
in accordance with the documentation. Add intel-telemetry support for
Gemini Lake. Various individual driver fixes noted below.
dell-wmi:
- Update dell_wmi_check_descriptor_buffer() to new model
intel-vbtn:
- reduce unnecessary messages for normal users
- match power button on press rather than release
intel-hid:
- reduce unnecessary messages for normal users
thinkpad_acpi:
- Fix warning about deprecated hwmon_device_register
wmi:
- Fix check for method instance number
ideapad-laptop:
- Expose conservation mode switch
intel_pmc_core:
- Make the driver PCH family agnostic
peaq-wmi:
- Evaluate wmi method with instance number 0x0
- silence a static checker warning
mxm-wmi:
- Evaluate wmi method with instance number 0x0
asus-wmi:
- Evaluate wmi method with instance number 0x0
intel_scu_ipc:
- make intel_scu_ipc_pdata_t const
intel_mid_powerbtn:
- make mid_pb_ddata const
- fix error return code in mid_pb_probe()
hp-wmi:
- Remove unused macro helper
- Correctly determine method id in WMI calls
dell-wmi:
- Fix driver interface version query
intel_telemetry:
- remove redundant macro definition
- Add GLK PSS Event Table
alienware-wmi:
- fix format string overflow warning
ibm_rtl:
- remove unnecessary static in ibm_rtl_write()
msi-wmi:
- remove unnecessary static in msi_wmi_notify()"
* tag 'platform-drivers-x86-v4.14-1' of git://git.infradead.org/linux-platform-drivers-x86: (23 commits)
platform/x86: dell-wmi: Update dell_wmi_check_descriptor_buffer() to new model
platform/x86: intel-vbtn: reduce unnecessary messages for normal users
platform/x86: intel-hid: reduce unnecessary messages for normal users
platform/x86: thinkpad_acpi: Fix warning about deprecated hwmon_device_register
platform/x86: wmi: Fix check for method instance number
platform/x86: ideapad-laptop: Expose conservation mode switch
platform/x86: intel_pmc_core: Make the driver PCH family agnostic
platform/x86: peaq-wmi: Evaluate wmi method with instance number 0x0
platform/x86: mxm-wmi: Evaluate wmi method with instance number 0x0
platform/x86: asus-wmi: Evaluate wmi method with instance number 0x0
platform/x86: intel_scu_ipc: make intel_scu_ipc_pdata_t const
platform/x86: intel_mid_powerbtn: make mid_pb_ddata const
platform/x86: intel_mid_powerbtn: fix error return code in mid_pb_probe()
platform/x86: hp-wmi: Remove unused macro helper
platform/x86: hp-wmi: Correctly determine method id in WMI calls
platform/x86: intel-vbtn: match power button on press rather than release
platform/x86: dell-wmi: Fix driver interface version query
platform/x86: intel_telemetry: remove redundant macro definition
platform/x86: intel_telemetry: Add GLK PSS Event Table
platform/x86: alienware-wmi: fix format string overflow warning
...
* pm-sleep:
ACPI / PM: Check low power idle constraints for debug only
PM / s2idle: Rename platform operations structure
PM / s2idle: Rename ->enter_freeze to ->enter_s2idle
PM / s2idle: Rename freeze_state enum and related items
PM / s2idle: Rename PM_SUSPEND_FREEZE to PM_SUSPEND_TO_IDLE
ACPI / PM: Prefer suspend-to-idle over S3 on some systems
platform/x86: intel-hid: Wake up Dell Latitude 7275 from suspend-to-idle
PM / suspend: Define pr_fmt() in suspend.c
PM / suspend: Use mem_sleep_labels[] strings in messages
PM / sleep: Put pm_test under CONFIG_PM_SLEEP_DEBUG
PM / sleep: Check pm_wakeup_pending() in __device_suspend_noirq()
PM / core: Add error argument to dpm_show_time()
PM / core: Split dpm_suspend_noirq() and dpm_resume_noirq()
PM / s2idle: Rearrange the main suspend-to-idle loop
PM / timekeeping: Print debug messages when requested
PM / sleep: Mark suspend/hibernation start and finish
PM / sleep: Do not print debug messages by default
PM / suspend: Export pm_suspend_target_state
This is now handled by use of a macro for device registration. The field
in iio_info will be going away shortly as it is no longer used.
Cc: <platform-driver-x86@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Azael Avalos <coproscefalo@gmail.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
This converts dell_wmi_check_descriptor_buffer() to the new driver
model interface and puts the interface version in dell_wmi_priv
where it belongs.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Unsupported events is only useful for developers and does not meaningful
for users. Using dev_dbg makes more sense and reduces noise in kernel
messages.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Unsupported events is only useful for developers and does not meaningful
for users. Using dev_dbg makes more sense and reduces noise in kernel
messages.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Use hwmon_device_register_with_groups instead of deprecated
hwmon_device_register and fix a dmesg warning.
This patch however changes the userspace API.
hwmon_device_register_with_groups takes `hwmon' name as an argument and
creates a name file in the `hwmon' device, not in the `platform_device'.
This allows us to remove custom `name' device attribute, but in order to
make lm-sensors happy we also have to move fans and thermal attributes
to the `hwmon' device.
Even though this patch changes userspace API, it's still compatible with
the lm-sensors. Starting with lm-sensors 3.0 (circa 2007), it looks at
both hwmon and the backing device for the name and other attributes.
before:
$ cat /sys/devices/platform/thinkpad_hwmon/{name,fan1_input}
thinkpad
2007
$ cat /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon1/{name,fan1_input}
cat: /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon1/name: No such file or directory
cat: /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon1/fan1_input: No such file or directory
$ cat /sys/class/hwmon/hwmon1/{name,fan1_input}
cat: /sys/class/hwmon/hwmon1/name: No such file or directory
cat: /sys/class/hwmon/hwmon1/fan1_input: No such file or directory
$ sensors
thinkpad-isa-0000
Adapter: ISA adapter
fan1: 3533 RPM
after:
$ cat /sys/devices/platform/thinkpad_hwmon/{name,fan1_input}
cat: /sys/devices/platform/thinkpad_hwmon/name: No such file or directory
cat: /sys/devices/platform/thinkpad_hwmon/fan1_input: No such file or directory
$ cat /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon1/{name,fan1_input}
thinkpad
3478
$ cat /sys/class/hwmon/hwmon1/{name,fan1_input}
thinkpad
3478
$ sensors
thinkpad-isa-0000
Adapter: ISA adapter
fan1: 3489 RPM
$ sensors -v
sensors version 3.4.0 with libsensors version 3.4.0
Signed-off-by: Stanislav Fomichev <kernel@fomichev.me>
[dvhart: cleaned up commit log, bumped version to 4.14 in the doc change]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
instance_count defines number of instances of data block and instance
itself is indexed from zero, which means first instance has number 0.
Therefore check for invalid instance should be non-strict inequality.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Darren Hart (VMware) <dvhart@infradead.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This exposes the battery conservation mode present on some (?) IdeaPads.
The mode is set by calling ACPI method SBMC with argument 3 (on) or
5 (off). Status is reported in bit 5 of the return value of ACPI method
GBMD.
Signed-off-by: Hao Wei Tee <angelsl@in04.sg>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Although this driver did pretty good job in abstracting PCH specific
interfaces, but still there are some loose ends. For example
SLP_S0 counter (for reading SLP_S0 residency), PM config offset (for
checking permissions to read XRAM) and PPFEAR offset (for reading IP
status) is still hardcoded for a specific family of PCH.
This change extended the struct pmc_reg_map to allow per family
configuration of offsets and bits.
No functional change is expected with this change. This change allows
seamless additions to new PCH and create a baseline for other platform
specific extensions.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
According to Hans de Goede, WMI interface of thh peaq-wmi module has 10
instances but corresponding ACPI WMBC method does not check Arg0 (instance
number) at all. Therefore evaluate WMI method with first instance number
(0x0) instead of second (0x1).
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
According to MXM 2.1 specification, there is the only one instance of the
WMI GUID F6CB5C3C-9CAE-4EBD-B577-931EA32A2CC0 and so it is instance 0x0.
MXM 2.1 specification:
https://lekensteyn.nl/files/docs/mxm-2.1-software-spec.pdf
_WDG dump:
// Methods GUID {F6CB5C3C-9CAE-4EBD-B577-931EA32A2CC0}
0x3C, 0x5C, 0xCB, 0xF6, 0xAE, 0x9C, 0xBD, 0x4E, 0xB5, 0x77, 0x93,
0x1E, 0xA3, 0x2A, 0x2C, 0xC0,
0x4D, 0x58, // Object ID "MX" = method "WMMX"
1, // Instance Count
0x02, // Flags (WMIACPI_REGFLAG_METHOD)
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
According to available DSDT dump from Asus machine, there is the only one
instance of the WMI GUID 97845ED0-4E6D-11DE-8A39-0800200C9A66 and so it is
0x0. Moreover corresponding method WMBC does not check Arg0 (instance
number) at all.
DSDT dump is available at:
https://lwn.net/Articles/391249/
_WDG dump:
0xD0, 0x5E, 0x84, 0x97, 0x6D, 0x4E, 0xDE, 0x11, 0x8A, 0x39, 0x08,
0x00, 0x20, 0x0C, 0x9A, 0x66,
0x42, 0x43, // Object ID "BC" = method "WMBC"
0x01, // Instance count
0x02, // Flags
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Make these const as they are only used during a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Make these const as they are only used during a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
platform_get_irq() returns an error code, but the intel_mid_powerbtn
driver ignores it and always returns -EINVAL. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.
Print error message and propagate the return value of platform_get_irq
on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The commit d8193cff33
("platform/x86: hp-wmi: Standardize enum usage for constants")
introduced a macro that had been never used.
Remove it.
Signed-off-by: Paulo Alcantara <pcacjr@zytor.com>
[andy wrote commit message]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The WMI queries are performed by evaluating the WMPV() method from ACPI
DSDT tables, and it takes three arguments: instance index, method id and
input data (buffer).
Currently the method id is hard-coded to 0x3 in hp_wmi_perform_query()
which means that it will perform WMI calls that expect an output data of
size 0x80 (128). The output size is usually OK for the WMI queries we
perform, however it would be better to pick the correct one before
evaluating the WMI method.
Which correct method id to choose can be figured out by looking at the
following ASL code from WVPI() method:
...
Name (PVSZ, Package (0x05)
{
Zero,
0x04,
0x80,
0x0400,
0x1000
})
Store (Zero, Local0)
If (LAnd (LGreaterEqual (Arg1, One), LLessEqual (Arg1, 0x05)))
{
Store (DerefOf (Index (PVSZ, Subtract (Arg1, One))), Local0)
}
...
Arg1 is the method id and PVSZ is the package used to index the
corresponding output size; 1 -> 0, 2 -> 4, 3 -> 128, 4 -> 1024, 5 ->
4096.
This patch maps the output size passed in hp_wmi_perform_query() to the
correct method id before evaluating the WMI method.
Signed-off-by: Paulo Alcantara <pcacjr@zytor.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This fixes a problem where the system gets stuck in a loop
unable to wakeup via power button in s2idle.
The problem happens because:
- press power button:
- system emits 0xc0 (power press), event ignored
- system emits 0xc1 (power release), event processed,
emited as KEY_POWER
- set wakeup_mode to true
- system goes to s2idle
- press power button
- system emits 0xc0 (power press), wakeup_mode is true,
system wakes
- system emits 0xc1 (power release), event processed,
emited as KEY_POWER
- system goes to s2idle again
To avoid this situation, process the presses (which matches what
intel-hid does too).
Verified on an Dell XPS 9365
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
This fixes a problem where the system gets stuck in a loop
unable to wakeup via power button in s2idle.
The problem happens because:
- press power button:
- system emits 0xc0 (power press), event ignored
- system emits 0xc1 (power release), event processed,
emited as KEY_POWER
- set wakeup_mode to true
- system goes to s2idle
- press power button
- system emits 0xc0 (power press), wakeup_mode is true,
system wakes
- system emits 0xc1 (power release), event processed,
emited as KEY_POWER
- system goes to s2idle again
To avoid this situation, process the presses (which matches what
intel-hid does too).
Verified on an Dell XPS 9365
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
When I converted dell-wmi to the new bus infrastructure, I left the
call to dell_wmi_check_descriptor_buffer() in dell_wmi_init(). This
could cause two problems:
- An error message when loading the driver on a system without
dell-wmi. We'd try to read the event descriptor even if the WMI
GUID wasn't there.
- A possible race if dell-wmi was loaded manually before wmi was
fully initialized.
Fix it by moving the call to the probe function where it belongs.
Fixes: bff589be59 ("platform/x86: dell-wmi: Convert to the WMI bus infrastructure")
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
On Dell Latitude 7275 the 5-button array is not exposed in the
ACPI tables, but still notifies are sent to the Intel HID device
object (device ID INT33D5) in response to power button actions while
suspended to idle. However, they are currently ignored as the
intel-hid driver is not prepared to take care of them.
As a result, power button wakeup from suspend-to-idle doesn't work
on this platform, but suspend-to-idle is the only reliable suspend
variant on it (the S3 implementation in the platform firmware turns
out to be broken), so it would be good to handle it properly.
For this reason, add an upfront check against the power button press
event (0xCE) to notify_handler() in the wakeup mode which allows it
to catch the power button wakeup notification on the affected
platform (even though priv->array is NULL on it) and should not
change the behavior on platforms with priv->array present (because
priv->array contains the event in question in those cases).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196115
Tested-by: Jérôme de Bretagne <jerome.debretagne@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-By: Mario Limonciello <mario.limonciello@dell.com>
When I converted dell-wmi to the new bus infrastructure, I left the
call to dell_wmi_check_descriptor_buffer() in dell_wmi_init(). This
could cause two problems:
- An error message when loading the driver on a system without
dell-wmi. We'd try to read the event descriptor even if the WMI
GUID wasn't there.
- A possible race if dell-wmi was loaded manually before wmi was
fully initialized.
Fix it by moving the call to the probe function where it belongs.
Fixes: bff589be59 ("platform/x86: dell-wmi: Convert to the WMI bus infrastructure")
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Some of the Primary Subsystem events differ on Gemini Lake but the IOSS
events remain same. This patch adds the updated PSS event table to enable
Telemetry driver on Gemini Lake.
Signed-off-by: Shanth Murthy <shanth.murthy@intel.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Reviewed-by: Souvik K Chakravarty <souvik.k.chakravarty@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
gcc points out a possible format string overflow for a large value of 'zone':
drivers/platform/x86/alienware-wmi.c: In function 'alienware_wmi_init':
drivers/platform/x86/alienware-wmi.c:461:24: error: '%02X' directive writing between 2 and 8 bytes into a region of size 6 [-Werror=format-overflow=]
sprintf(buffer, "zone%02X", i);
^~~~
drivers/platform/x86/alienware-wmi.c:461:19: note: directive argument in the range [0, 2147483646]
sprintf(buffer, "zone%02X", i);
^~~~~~~~~~
drivers/platform/x86/alienware-wmi.c:461:3: note: 'sprintf' output between 7 and 13 bytes into a destination of size 10
This replaces the 'int' variable with an 'u8' to make sure
it always fits, renaming the variable to 'zone' for clarity.
Unfortunately, gcc-7.1.1 still warns about it with that change, which
seems to be unintended by the gcc developers. I have opened a bug
against gcc with a reduced test case. As a workaround, I also
change the format string to use "%02hhX", which shuts up the
warning in that version.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81483
Link: https://patchwork.ozlabs.org/patch/788415/
Suggested-by: Andy Shevchenko <andy@infradead.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[andy: added empty lines after u8 zone; definitions]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Remove unnecessary static on local variable cmd_port_val. Such variable
is initialized before being used, on every execution path throughout
the function. The static has no benefit and, removing it reduces the
object file size.
This issue was detected using Coccinelle and the following semantic patch:
https://github.com/GustavoARSilva/coccinelle/blob/master/static/static_unused.cocci
In the following log you can see a difference in the object file size.
This log is the output of the size command, before and after the code
change:
before:
text data bss dec hex filename
3932 3440 512 7884 1ecc drivers/platform/x86/ibm_rtl.o
after:
text data bss dec hex filename
3887 3384 448 7719 1e27 drivers/platform/x86/ibm_rtl.o
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Remove unnecessary static on local variable _key_. Such variable is
initialized before being used, on every execution path throughout
the function. The static has no benefit and, removing it reduces
the object file size.
This issue was detected using Coccinelle and the following semantic patch:
https://github.com/GustavoARSilva/coccinelle/blob/master/static/static_unused.cocci
In the following log you can see a significant difference in the object
file size. Also, there is a significant difference in the bss segment.
This log is the output of the size command, before and after the code
change:
before:
text data bss dec hex filename
6530 3736 320 10586 295a drivers/platform/x86/msi-wmi.o
after:
text data bss dec hex filename
6494 3648 256 10398 289e drivers/platform/x86/msi-wmi.o
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is a harmless static checker warning here that unsigned values are
always >= 0. The code looks like:
if (peaq_ignore_events_counter && --peaq_ignore_events_counter >= 0)
The first part of the condition ensures that we never wrap around so the
code works as intended. I've tweaked it slightly to avoid the warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The order of resource deallocations is messed up in acpi_wmi_init().
It should be vice versa.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
The new driver fails to build without INPUT_POLLDEV
drivers/platform/x86/peaq-wmi.o: In function `peaq_wmi_exit':
peaq-wmi.c:(.exit.text+0x1c): undefined reference to `input_unregister_polled_device'
drivers/platform/x86/peaq-wmi.o: In function `peaq_wmi_init':
peaq-wmi.c:(.init.text+0x23): undefined reference to `input_allocate_polled_device'
peaq-wmi.c:(.init.text+0x18e): undefined reference to `input_register_polled_device'
For some reason, all other drivers that need this use 'select'
here rather than 'depends on', so I'm doing the same.
Fixes: 13bb0fd551 ("platform/x86: peaq-wmi: Add new peaq-wmi driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Pull MIPS updates from Ralf Baechle:
"Boston platform support:
- Document DT bindings
- Add CLK driver for board clocks
CM:
- Avoid per-core locking with CM3 & higher
- WARN on attempt to lock invalid VP, not BUG
CPS:
- Select CONFIG_SYS_SUPPORTS_SCHED_SMT for MIPSr6
- Prevent multi-core with dcache aliasing
- Handle cores not powering down more gracefully
- Handle spurious VP starts more gracefully
DSP:
- Add lwx & lhx missaligned access support
eBPF:
- Add MIPS support along with many supporting change to add the
required infrastructure
Generic arch code:
- Misc sysmips MIPS_ATOMIC_SET fixes
- Drop duplicate HAVE_SYSCALL_TRACEPOINTS
- Negate error syscall return in trace
- Correct forced syscall errors
- Traced negative syscalls should return -ENOSYS
- Allow samples/bpf/tracex5 to access syscall arguments for sane
traces
- Cleanup from old Kconfig options in defconfigs
- Fix PREF instruction usage by memcpy for MIPS R6
- Fix various special cases in the FPU eulation
- Fix some special cases in MIPS16e2 support
- Fix MIPS I ISA /proc/cpuinfo reporting
- Sort MIPS Kconfig alphabetically
- Fix minimum alignment requirement of IRQ stack as required by
ABI / GCC
- Fix special cases in the module loader
- Perform post-DMA cache flushes on systems with MAARs
- Probe the I6500 CPU
- Cleanup cmpxchg and add support for 1 and 2 byte operations
- Use queued read/write locks (qrwlock)
- Use queued spinlocks (qspinlock)
- Add CPU shared FTLB feature detection
- Handle tlbex-tlbp race condition
- Allow storing pgd in C0_CONTEXT for MIPSr6
- Use current_cpu_type() in m4kc_tlbp_war()
- Support Boston in the generic kernel
Generic platform:
- yamon-dt: Pull YAMON DT shim code out of SEAD-3 board
- yamon-dt: Support > 256MB of RAM
- yamon-dt: Use serial* rather than uart* aliases
- Abstract FDT fixup application
- Set RTC_ALWAYS_BCD to 0
- Add a MAINTAINERS entry
core kernel:
- qspinlock.c: include linux/prefetch.h
Loongson 3:
- Add support
Perf:
- Add I6500 support
SEAD-3:
- Remove GIC timer from DT
- Set interrupt-parent per-device, not at root node
- Fix GIC interrupt specifiers
SMP:
- Skip IPI setup if we only have a single CPU
VDSO:
- Make comment match reality
- Improvements to time code in VDSO"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (86 commits)
locking/qspinlock: Include linux/prefetch.h
MIPS: Fix MIPS I ISA /proc/cpuinfo reporting
MIPS: Fix minimum alignment requirement of IRQ stack
MIPS: generic: Support MIPS Boston development boards
MIPS: DTS: img: Don't attempt to build-in all .dtb files
clk: boston: Add a driver for MIPS Boston board clocks
dt-bindings: Document img,boston-clock binding
MIPS: Traced negative syscalls should return -ENOSYS
MIPS: Correct forced syscall errors
MIPS: Negate error syscall return in trace
MIPS: Drop duplicate HAVE_SYSCALL_TRACEPOINTS select
MIPS16e2: Provide feature overrides for non-MIPS16 systems
MIPS: MIPS16e2: Report ASE presence in /proc/cpuinfo
MIPS: MIPS16e2: Subdecode extended LWSP/SWSP instructions
MIPS: MIPS16e2: Identify ASE presence
MIPS: VDSO: Fix a mismatch between comment and preprocessor constant
MIPS: VDSO: Add implementation of gettimeofday() fallback
MIPS: VDSO: Add implementation of clock_gettime() fallback
MIPS: VDSO: Fix conversions in do_monotonic()/do_monotonic_coarse()
MIPS: Use current_cpu_type() in m4kc_tlbp_war()
...
This Ployer Momo7w revision has the same hardware as the Trekstor
ST70416-6, so we re-use the surftab_wintron70_st70416_6_data.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Changes in this pull request are around catching up
cros_ec with the internal chromeos-kernel versions of
cros_ec, cros_ec_lpc, and cros_ec_lightbar.
Also, switching maintainership from olof to bleung.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QtSr
-----END PGP SIGNATURE-----
Merge tag 'chrome-platform-for-linus-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform
Pull chrome platform updates from Benson Leung:
"Changes in this pull request are around catching up cros_ec with the
internal chromeos-kernel versions of cros_ec, cros_ec_lpc, and
cros_ec_lightbar.
Also, switching maintainership from olof to bleung"
* tag 'chrome-platform-for-linus-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
platform/chrome : Add myself as Maintainer
platform/chrome: cros_ec_lightbar - hide unused PM functions
cros_ec: Don't signal wake event for non-wake host events
cros_ec: Fix deadlock when EC is not responsive at probe
cros_ec: Don't return error when checking command version
platform/chrome: cros_ec_lightbar - Avoid I2C xfer to EC during suspend
platform/chrome: cros_ec_lightbar - Add userspace lightbar control bit to EC
platform/chrome: cros_ec_lightbar - Control of suspend/resume lightbar sequence
platform/chrome: cros_ec_lightbar - Add lightbar program feature to sysfs
platform/chrome: cros_ec_lpc: Add MKBP events support over ACPI
platform/chrome: cros_ec_lpc: Add power management ops
platform/chrome: cros_ec_lpc: Add support for GOOG004 ACPI device
platform/chrome: cros_ec_lpc: Add support for mec1322 EC
platform/chrome: cros_ec_lpc: Add R/W helpers to LPC protocol variants
mfd: cros_ec: Add support for dumping panic information
cros_ec_debugfs: Pass proper struct sizes to cros_ec_cmd_xfer()
mfd: cros_ec: add debugfs, console log file
mfd: cros_ec: Add EC console read structures definitions
mfd: cros_ec: Add helper for event notifier.
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
26360 1072 24 27456 6b40 drivers/platform/x86/toshiba_acpi.o
File size After adding 'const':
text data bss dec hex filename
26424 1008 24 27456 6b40 drivers/platform/x86/toshiba_acpi.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
13140 840 1 13981 369d drivers/platform/x86/asus-wmi.o
File size After adding 'const':
text data bss dec hex filename
13268 712 1 13981 368d drivers/platform/x86/asus-wmi.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
2505 600 4 3109 c25 drivers/platform/x86/panasonic-laptop.o
File size After adding 'const':
text data bss dec hex filename
2569 536 4 3109 c25 drivers/platform/x86/panasonic-laptop.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
6932 1016 48 7996 1f3c drivers/platform/x86/alienware-wmi.o
File size After adding 'const':
text data bss dec hex filename
7060 888 48 7996 1f64 drivers/platform/x86/alienware-wmi.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
8710 5452 23 14185 3769 drivers/platform/x86/samsung-laptop.o
File size After adding 'const':
text data bss dec hex filename
8774 5388 23 14185 3769 drivers/platform/x86/samsung-laptop.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
6781 6144 34 12959 329f drivers/platform/x86/compal-laptop.o
File size After adding 'const':
text data bss dec hex filename
6845 6080 34 12959 329f drivers/platform/x86/compal-laptop.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
7474 1205 24 8703 21ff drivers/platform/x86/fujitsu-laptop.o
File size After adding 'const':
text data bss dec hex filename
7538 1141 24 8703 21ff drivers/platform/x86/fujitsu-laptop.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
If peaq_ignore_events_counter gets set to 1 we should skip polling 1
time, rather then ignoring it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Pull MFD updates from Lee Jones:
"New Drivers:
- Intel Cherry Trail Whiskey Cove PMIC
- TI LP87565 PMIC
New Device Support:
- Add support for Cannonlake to intel-lpss-pci
- Add support for Simatic IOT2000 to intel_quark_i2c_gpio
New Functionality:
- Add Regulator support (axp20x)
Fix-ups:
- Rework IRQ handling (intel_soc_pmic_bxtwc, rtsx_pcr, cros_ec)
- Remove unused/unwelcome code (ipaq-micro, wm831x-core, da9062-core)
- Provide deregistration on unbind (rn5t618)
- Rework DT code/documentation (arizona)
- Constify things (fsl-imx25-tsadc)
- MAINTAINERS updates (DA9062/61)
- Kconfig configuration adaptions (INTEL_SOC_PMIC, MFD_AXP20X_I2C)
- Switch to DMI matching (intel_quark_i2c_gpio)
- Provide an appropriate level of error checking (wm831x-{i2c,spi},
twl4030-irq, tc6393xb)
- Make use of devm_* (resource handling) calls (intel_soc_pmic_bxtwc,
stm32-timers, atmel-flexcom, cros_ec, fsl-imx25-tsadc,
exynos-lpass, palmas, qcom-spmi-pmic, smsc-ece1099,
motorola-cpcap)"
[ Skipped the last commit in that series that added eight thousand
lines of pointless repeated register definitions. - Linus ]
* tag 'mfd-next-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (38 commits)
mfd: Add LP87565 PMIC support
mfd: cros_ec: Free IRQ on exit
dt-bindings: vendor-prefixes: Add arctic to vendor prefix
mfd: da9061: Fix to remove BBAT_CONT register from chip model
mfd: da9061: Fix to remove BBAT_CONT register from chip model
mfd: axp20x-i2c: Document that this must be builtin on x86
mfd: Add Cherry Trail Whiskey Cove PMIC driver
mfd: tc6393xb: Handle return value of clk_prepare_enable
mfd: intel_quark_i2c_gpio: Add support for SIMATIC IOT2000 platform
mfd: intel_quark_i2c_gpio: Use dmi_system_id table for retrieving frequency
mfd: motorola-cpcap: Use devm_of_platform_populate()
mfd: smsc-ece: Use devm_of_platform_populate()
mfd: qcom-spmi-pmic: Use devm_of_platform_populate()
mfd: palmas: Use devm_of_platform_populate()
mfd: exynos: Use devm_of_platform_populate()
mfd: fsl-imx25: Use devm_of_platform_populate()
mfd: cros_ec: Use devm_of_platform_populate()
mfd: atmel: Use devm_of_platform_populate()
mfd: stm32-timers: Use devm_of_platform_populate()
mfd: intel_soc_pmic: Select designware i2c-bus driver
...
Check return value from call to devm_kzalloc()
in order to prevent a NULL pointer dereference.
This issue was detected using Coccinelle and the following semantic patch:
@@
expression x;
identifier fld;
@@
* x = devm_kzalloc(...);
... when != x == NULL
x->fld
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Add touchscreen info for I.T.Works TW891 2-in-1.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Introduce new bus architecture for WMI and expose BMOF data through
sysfs. Correct several assumptions about WMI instance number from 1 to
0. Further fujitsu-laptop cleanups, continuing to prepare for separation
into two modules. Add support for several new ideapad laptops and
silead-based tablets. Various minor fixes and const cleanups.
sony-laptop:
- constify attribute_group and input index array
fujitsu-laptop:
- rework debugging
- do not evaluate ACPI _INI methods
- do not update ACPI device power status
- sanitize hotkey input device identification
- use strcpy to set ACPI device names and classes
- remove redundant safety checks
- use device-specific data in remaining module code
- use device-specific data in LED-related code
- explicitly pass ACPI device to call_fext_func()
- track the last instantiated FUJ02E3 ACPI device
- allocate fujitsu_laptop in acpi_fujitsu_laptop_add()
- use device-specific data in backlight code
- allocate fujitsu_bl in acpi_fujitsu_bl_add()
- distinguish current uses of device-specific data
msi-laptop:
- constify msipf*_attribute_group
eeepc-laptop:
- constify platform_attribute_group
toshiba_haps:
- constify haps_attr_group
dell-wmi-led:
- Adjust instance of wmi_evaluate_method calls to 0
alienware-wmi:
- Adjust instance of wmi_evaluate_method calls to 0
intel_menlow:
- Add const to thermal_cooling_device_ops structure
acerhdf:
- Add const to thermal_cooling_device_ops structure
dell-laptop:
- Fix bogus keyboard backlight sysfs interface
acer-wmi:
- Using zero as first WMI instance number
- Detect RF Button capability
ideapad-laptop:
- Add Y720-15IKBN to no_hw_rfkill
- Add Y520-15IKBN to no_hw_rfkill
- constify rfkill_ops structure
- Squelch ACPI event 1
- hide unused 'touchpad_store'
- Switch touchpad attribute to be RO
- Add sysfs interface for touchpad state
silead_dmi:
- Add touchscreen info for PoV mobii wintab p800w
- Add touchscreen info for Pipo W2S tablet
- Add touchscreen info for GP-electronic T701
dell-rbtn:
- constify rfkill_ops structures
- Improve explanation about DELLABC6
samsung-laptop:
- constify rfkill_ops structures
panasonic-laptop:
- remove unused code
samsung-laptop:
- Initialize loca variable
dell-wmi:
- Convert to the WMI bus infrastructure
- Add a better description for "stealth mode"
- Add a comment explaining the 0xb2 magic number
wmi-bmof:
- New driver to expose embedded Binary WMI MOF metadata
wmi*:
- Fix printing info about WDG structure
- Add recent copyright statements
- Require query for data blocks, rename writable to setable
- Add an interface for subdrivers to access sibling devices
- Bind the platform device, not the ACPI node
- Add a new interface to read block data
- Incorporate acpi_install_notify_handler
- Instantiate all devices before adding them
- Probe data objects for read and write capabilities
- Split devices into types and add basic sysfs attributes
- Fix error handling when creating devices
- Turn WMI into a bus driver
- Track wmi devices per ACPI device
- Clean up acpi_wmi_add
- Pass the acpi_device through to parse_wdg
- Drop "Mapper (un)loaded" messages
intel_cht_int33fe:
- Set supplied-from property on max17047 dev
intel_pmc_ipc:
- Mark ipc_data_readb() as __maybe_unused
topstar-laptop:
- Add new device id
peaq-wmi:
- Add new peaq-wmi driver
thinkpad_acpi:
- Add a comment about 0 in module_param_call()
- Join string literals back
toshiba_acpi:
- use memdup_user_nul
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZXSzcAAoJEKbMaAwKp364hSEIAKC0xJRZWv1aI1f69JCSZR0+
5/6tMsps9nK4LtaKQCvPHeOCxmwpE4tZYzyuYHyHW+pfUMquIdRVQRMe3u2FTrKS
HuvCgmYAkZqCzy/zQIPaVU2K9m7/9HubXYy0Q1qkjlGZp/IYMFoeo7DU65Ajm+HS
wrRXIYIKSbjAU0pmzW//MFauEi26MWpAHMraw+HCJbXcGwhokSrtTYitqFpQXnhJ
kdguSkEluW1NoG3Tv7CbfXWXge7zwxlrmI06b4FtkpFK6b2LCZcYeUhIn33yNYT1
IwhNOsaWlxNw3K3c1IRZSwYoJ6dmBJ+cxmZ0sd3cr8jahgpHB/nJiRElHmTdf2M=
=PbWU
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.13-1' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Introduce new bus architecture for WMI and expose BMOF data through
sysfs. Correct several assumptions about WMI instance number from 1 to
0. Further fujitsu-laptop cleanups, continuing to prepare for
separation into two modules. Add support for several new ideapad
laptops and silead-based tablets. Various minor fixes and const
cleanups.
Detail summary:
sony-laptop:
- constify attribute_group and input index array
fujitsu-laptop:
- rework debugging
- do not evaluate ACPI _INI methods
- do not update ACPI device power status
- sanitize hotkey input device identification
- use strcpy to set ACPI device names and classes
- remove redundant safety checks
- use device-specific data in remaining module code
- use device-specific data in LED-related code
- explicitly pass ACPI device to call_fext_func()
- track the last instantiated FUJ02E3 ACPI device
- allocate fujitsu_laptop in acpi_fujitsu_laptop_add()
- use device-specific data in backlight code
- allocate fujitsu_bl in acpi_fujitsu_bl_add()
- distinguish current uses of device-specific data
msi-laptop:
- constify msipf*_attribute_group
eeepc-laptop:
- constify platform_attribute_group
toshiba_haps:
- constify haps_attr_group
dell-wmi-led:
- Adjust instance of wmi_evaluate_method calls to 0
alienware-wmi:
- Adjust instance of wmi_evaluate_method calls to 0
intel_menlow:
- Add const to thermal_cooling_device_ops structure
acerhdf:
- Add const to thermal_cooling_device_ops structure
dell-laptop:
- Fix bogus keyboard backlight sysfs interface
acer-wmi:
- Using zero as first WMI instance number
- Detect RF Button capability
ideapad-laptop:
- Add Y720-15IKBN to no_hw_rfkill
- Add Y520-15IKBN to no_hw_rfkill
- constify rfkill_ops structure
- Squelch ACPI event 1
- hide unused 'touchpad_store'
- Switch touchpad attribute to be RO
- Add sysfs interface for touchpad state
silead_dmi:
- Add touchscreen info for PoV mobii wintab p800w
- Add touchscreen info for Pipo W2S tablet
- Add touchscreen info for GP-electronic T701
dell-rbtn:
- constify rfkill_ops structures
- Improve explanation about DELLABC6
samsung-laptop:
- constify rfkill_ops structures
panasonic-laptop:
- remove unused code
samsung-laptop:
- Initialize loca variable
dell-wmi:
- Convert to the WMI bus infrastructure
- Add a better description for "stealth mode"
- Add a comment explaining the 0xb2 magic number
wmi-bmof:
- New driver to expose embedded Binary WMI MOF metadata
wmi*:
- Fix printing info about WDG structure
- Add recent copyright statements
- Require query for data blocks, rename writable to setable
- Add an interface for subdrivers to access sibling devices
- Bind the platform device, not the ACPI node
- Add a new interface to read block data
- Incorporate acpi_install_notify_handler
- Instantiate all devices before adding them
- Probe data objects for read and write capabilities
- Split devices into types and add basic sysfs attributes
- Fix error handling when creating devices
- Turn WMI into a bus driver
- Track wmi devices per ACPI device
- Clean up acpi_wmi_add
- Pass the acpi_device through to parse_wdg
- Drop "Mapper (un)loaded" messages
intel_cht_int33fe:
- Set supplied-from property on max17047 dev
intel_pmc_ipc:
- Mark ipc_data_readb() as __maybe_unused
topstar-laptop:
- Add new device id
peaq-wmi:
- Add new peaq-wmi driver
thinkpad_acpi:
- Add a comment about 0 in module_param_call()
- Join string literals back
toshiba_acpi:
- use memdup_user_nul"
* tag 'platform-drivers-x86-v4.13-1' of git://git.infradead.org/linux-platform-drivers-x86: (67 commits)
platform/x86: sony-laptop: constify attribute_group and input index array
platform/x86: fujitsu-laptop: rework debugging
platform/x86: fujitsu-laptop: do not evaluate ACPI _INI methods
platform/x86: fujitsu-laptop: do not update ACPI device power status
platform/x86: fujitsu-laptop: sanitize hotkey input device identification
platform/x86: fujitsu-laptop: use strcpy to set ACPI device names and classes
platform/x86: fujitsu-laptop: remove redundant safety checks
platform/x86: msi-laptop: constify msipf*_attribute_group
platform/x86: eeepc-laptop: constify platform_attribute_group
platform/x86: toshiba_haps: constify haps_attr_group
platform/x86: dell-wmi-led: Adjust instance of wmi_evaluate_method calls to 0
platform/x86: alienware-wmi: Adjust instance of wmi_evaluate_method calls to 0
platform/x86: intel_menlow: Add const to thermal_cooling_device_ops structure
platform/x86: acerhdf: Add const to thermal_cooling_device_ops structure
platform/x86: dell-laptop: Fix bogus keyboard backlight sysfs interface
platform/x86: acer-wmi: Using zero as first WMI instance number
platform/x86: ideapad-laptop: Add Y720-15IKBN to no_hw_rfkill
platform/x86: ideapad-laptop: Add Y520-15IKBN to no_hw_rfkill
platform/x86: silead_dmi: Add touchscreen info for PoV mobii wintab p800w
platform/x86: silead_dmi: Add touchscreen info for Pipo W2S tablet
...
There are couple of places where 8 spaces are used instead of tabs.
Replace former by latter. No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Some Lenovo ideapad models do not have hardware rfkill switches, but
trying to read the rfkill switches through the ideapad-laptop module.
It caused to always reported blocking breaking wifi.
Fix it by adding those models to no_hw_rfkill_list.
Signed-off-by: Yang Jiaxun <yjx@flygoat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Like other Lenovo models the IdeaPad V510-15IKB does not have an hw
rfkill switch. This results in hard-blocked radios after boot, resulting
in always blocked radios rendering them unusable.
Add the IdeaPad V510-15IKB to the no_hw_rfkill DMI list and allows using
the built-in radios.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This adds a debugfs consumer for the exported kernel API
intel_pmc_read_s0ix_residency. This debugfs entry reads S0ix residency
directly from the PMC hardware counters.
TEST:
- echo freeze > /sys/power/state
- Wake the system, read the S0ix residency i.e.
cat /sys/kernel/debug/telemetry/s0ix_residency_usec
Signed-off-by: Shanth Murthy <shanth.murthy@intel.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There are bunch of "goto out;" paths where we don't set the error code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
- Rework suspend-to-idle to allow it to take wakeup events signaled
by the EC into account on ACPI-based platforms in order to properly
support power button wakeup from suspend-to-idle on recent Dell
laptops (Rafael Wysocki).
That includes the core suspend-to-idle code rework, support for
the Low Power S0 _DSM interface, and support for the ACPI INT0002
Virtual GPIO device from Hans de Goede (required for USB keyboard
wakeup from suspend-to-idle to work on some machines).
- Stop trying to export the current CPU frequency via /proc/cpuinfo
on x86 as that is inaccurate and confusing (Len Brown).
- Rework the way in which the current CPU frequency is exported by
the kernel (over the cpufreq sysfs interface) on x86 systems with
the APERF and MPERF registers by always using values read from
these registers, when available, to compute the current frequency
regardless of which cpufreq driver is in use (Len Brown).
- Rework the PCI/ACPI device wakeup infrastructure to remove the
questionable and artificial distinction between "devices that
can wake up the system from sleep states" and "devices that can
generate wakeup signals in the working state" from it, which
allows the code to be simplified quite a bit (Rafael Wysocki).
- Fix the wakeup IRQ framework by making it use SRCU instead of
RCU which doesn't allow sleeping in the read-side critical
sections, but which in turn is expected to be allowed by the
IRQ bus locking infrastructure (Thomas Gleixner).
- Modify some computations in the intel_pstate driver to avoid
rounding errors resulting from them (Srinivas Pandruvada).
- Reduce the overhead of the intel_pstate driver in the HWP
(hardware-managed P-states) mode and when the "performance"
P-state selection algorithm is in use by making it avoid
registering scheduler callbacks in those cases (Len Brown).
- Rework the energy_performance_preference sysfs knob in
intel_pstate by changing the values that correspond to
different symbolic hint names used by it (Len Brown).
- Make it possible to use more than one cpuidle driver at the same
time on ARM (Daniel Lezcano).
- Make it possible to prevent the cpuidle menu governor from using
the 0 state by disabling it via sysfs (Nicholas Piggin).
- Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1
on AMD systems (Yazen Ghannam).
- Make the CPPC cpufreq driver take the lowest nonlinear performance
information into account (Prashanth Prakash).
- Add support for hi3660 to the cpufreq-dt driver, fix the
imx6q driver and clean up the sfi, exynos5440 and intel_pstate
drivers (Colin Ian King, Krzysztof Kozlowski, Octavian Purdila,
Rafael Wysocki, Tao Wang).
- Fix a few minor issues in the generic power domains (genpd)
framework and clean it up somewhat (Krzysztof Kozlowski,
Mikko Perttunen, Viresh Kumar).
- Fix a couple of minor issues in the operating performance points
(OPP) framework and clean it up somewhat (Viresh Kumar).
- Fix a CONFIG dependency in the hibernation core and clean it up
slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
- Add rk3228 support to the rockchip-io adaptive voltage scaling
(AVS) driver (David Wu).
- Fix an incorrect bit shift operation in the RAPL power capping
driver (Adam Lessnau).
- Add support for the EPP field in the HWP (hardware managed
P-states) control register, HWP.EPP, to the x86_energy_perf_policy
tool and update msr-index.h with HWP.EPP values (Len Brown).
- Fix some minor issues in the turbostat tool (Len Brown).
- Add support for AMD family 0x17 CPUs to the cpupower tool and fix
a minor issue in it (Sherry Hurwitz).
- Assorted cleanups, mostly related to the constification of some
data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
Kozlowski).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Wsph
-----END PGP SIGNATURE-----
Merge tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The big ticket items here are the rework of suspend-to-idle in order
to add proper support for power button wakeup from it on recent Dell
laptops and the rework of interfaces exporting the current CPU
frequency on x86.
In addition to that, support for a few new pieces of hardware is
added, the PCI/ACPI device wakeup infrastructure is simplified
significantly and the wakeup IRQ framework is fixed to unbreak the IRQ
bus locking infrastructure.
Also, there are some functional improvements for intel_pstate, tools
updates and small fixes and cleanups all over.
Specifics:
- Rework suspend-to-idle to allow it to take wakeup events signaled
by the EC into account on ACPI-based platforms in order to properly
support power button wakeup from suspend-to-idle on recent Dell
laptops (Rafael Wysocki).
That includes the core suspend-to-idle code rework, support for the
Low Power S0 _DSM interface, and support for the ACPI INT0002
Virtual GPIO device from Hans de Goede (required for USB keyboard
wakeup from suspend-to-idle to work on some machines).
- Stop trying to export the current CPU frequency via /proc/cpuinfo
on x86 as that is inaccurate and confusing (Len Brown).
- Rework the way in which the current CPU frequency is exported by
the kernel (over the cpufreq sysfs interface) on x86 systems with
the APERF and MPERF registers by always using values read from
these registers, when available, to compute the current frequency
regardless of which cpufreq driver is in use (Len Brown).
- Rework the PCI/ACPI device wakeup infrastructure to remove the
questionable and artificial distinction between "devices that can
wake up the system from sleep states" and "devices that can
generate wakeup signals in the working state" from it, which allows
the code to be simplified quite a bit (Rafael Wysocki).
- Fix the wakeup IRQ framework by making it use SRCU instead of RCU
which doesn't allow sleeping in the read-side critical sections,
but which in turn is expected to be allowed by the IRQ bus locking
infrastructure (Thomas Gleixner).
- Modify some computations in the intel_pstate driver to avoid
rounding errors resulting from them (Srinivas Pandruvada).
- Reduce the overhead of the intel_pstate driver in the HWP
(hardware-managed P-states) mode and when the "performance" P-state
selection algorithm is in use by making it avoid registering
scheduler callbacks in those cases (Len Brown).
- Rework the energy_performance_preference sysfs knob in intel_pstate
by changing the values that correspond to different symbolic hint
names used by it (Len Brown).
- Make it possible to use more than one cpuidle driver at the same
time on ARM (Daniel Lezcano).
- Make it possible to prevent the cpuidle menu governor from using
the 0 state by disabling it via sysfs (Nicholas Piggin).
- Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1 on
AMD systems (Yazen Ghannam).
- Make the CPPC cpufreq driver take the lowest nonlinear performance
information into account (Prashanth Prakash).
- Add support for hi3660 to the cpufreq-dt driver, fix the imx6q
driver and clean up the sfi, exynos5440 and intel_pstate drivers
(Colin Ian King, Krzysztof Kozlowski, Octavian Purdila, Rafael
Wysocki, Tao Wang).
- Fix a few minor issues in the generic power domains (genpd)
framework and clean it up somewhat (Krzysztof Kozlowski, Mikko
Perttunen, Viresh Kumar).
- Fix a couple of minor issues in the operating performance points
(OPP) framework and clean it up somewhat (Viresh Kumar).
- Fix a CONFIG dependency in the hibernation core and clean it up
slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
- Add rk3228 support to the rockchip-io adaptive voltage scaling
(AVS) driver (David Wu).
- Fix an incorrect bit shift operation in the RAPL power capping
driver (Adam Lessnau).
- Add support for the EPP field in the HWP (hardware managed
P-states) control register, HWP.EPP, to the x86_energy_perf_policy
tool and update msr-index.h with HWP.EPP values (Len Brown).
- Fix some minor issues in the turbostat tool (Len Brown).
- Add support for AMD family 0x17 CPUs to the cpupower tool and fix a
minor issue in it (Sherry Hurwitz).
- Assorted cleanups, mostly related to the constification of some
data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
Kozlowski)"
* tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (69 commits)
cpufreq: Update scaling_cur_freq documentation
cpufreq: intel_pstate: Clean up after performance governor changes
PM: hibernate: constify attribute_group structures.
cpuidle: menu: allow state 0 to be disabled
intel_idle: Use more common logging style
PM / Domains: Fix missing default_power_down_ok comment
PM / Domains: Fix unsafe iteration over modified list of domains
PM / Domains: Fix unsafe iteration over modified list of domain providers
PM / Domains: Fix unsafe iteration over modified list of device links
PM / Domains: Handle safely genpd_syscore_switch() call on non-genpd device
PM / Domains: Call driver's noirq callbacks
PM / core: Drop run_wake flag from struct dev_pm_info
PCI / PM: Simplify device wakeup settings code
PCI / PM: Drop pme_interrupt flag from struct pci_dev
ACPI / PM: Consolidate device wakeup settings code
ACPI / PM: Drop run_wake from struct acpi_device_wakeup_flags
PM / QoS: constify *_attribute_group.
PM / AVS: rockchip-io: add io selectors and supplies for rk3228
powercap/RAPL: prevent overridding bits outside of the mask
PM / sysfs: Constify attribute groups
...
Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates, and
a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only reported
issue being a merge problem with this tree and the jc-docs tree in the
w1 documentation area. The fix should be obvious for what to do when it
happens, if not, we can send a follow-up patch for it afterward.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpXKA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynLrQCdG9SxRjAbOd6pT9Fr2NAzpUG84YsAoLw+I3iO
EMi60UXWqAFJbtVMS9Aj
=yrSq
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates,
and a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only
reported issue being a merge problem with this tree and the jc-docs
tree in the w1 documentation area"
* tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (147 commits)
misc: apds990x: Use sysfs_match_string() helper
mei: drop unreachable code in mei_start
mei: validate the message header only in first fragment.
DocBook: w1: Update W1 file locations and names in DocBook
mux: adg792a: always require I2C support
nvmem: rockchip-efuse: add support for rk322x-efuse
nvmem: core: add locking to nvmem_find_cell
nvmem: core: Call put_device() in nvmem_unregister()
nvmem: core: fix leaks on registration errors
nvmem: correct Broadcom OTP controller driver writes
w1: Add subsystem kernel public interface
drivers/fsi: Add module license to core driver
drivers/fsi: Use asynchronous slave mode
drivers/fsi: Add hub master support
drivers/fsi: Add SCOM FSI client device driver
drivers/fsi/gpio: Add tracepoints for GPIO master
drivers/fsi: Add GPIO based FSI master
drivers/fsi: Document FSI master sysfs files in ABI
drivers/fsi: Add error handling for slave
drivers/fsi: Add tracepoints for low-level operations
...
Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpX4A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymobgCfd0d13IfpZoq1N41wc6z2Z0xD7cwAnRMeH1/p
kEeISGpHPYP9f8PBh9FO
=Hfqt
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues"
* tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (56 commits)
arm: mach-rpc: ecard: fix build error
zram: convert remaining CLASS_ATTR() to CLASS_ATTR_RO()
driver-core: remove struct bus_type.dev_attrs
powerpc: vio_cmo: use dev_groups and not dev_attrs for bus_type
powerpc: vio: use dev_groups and not dev_attrs for bus_type
USB: usbip: convert to use DRIVER_ATTR_RW
s390: drivers: convert to use DRIVER_ATTR_RO/WO
platform: thinkpad_acpi: convert to use DRIVER_ATTR_RO/RW
pcmcia: ds: convert to use DRIVER_ATTR_RO
wireless: ipw2x00: convert to use DRIVER_ATTR_RW
net: ehea: convert to use DRIVER_ATTR_RO
net: caif: convert to use DRIVER_ATTR_RO
TTY: hvc: convert to use DRIVER_ATTR_RW
PCI: pci-driver: convert to use DRIVER_ATTR_WO
IB: nes: convert to use DRIVER_ATTR_RW
HID: hid-core: convert to use DRIVER_ATTR_RO and drv_groups
arm: ecard: fix dev_groups patch typo
tty: serdev: use dev_groups and not dev_attrs for bus_type
sparc: vio: use dev_groups and not dev_attrs for bus_type
hid: intel-ish-hid: use dev_groups and not dev_attrs for bus_type
...
* acpi-pm:
PM / core: Drop run_wake flag from struct dev_pm_info
PCI / PM: Simplify device wakeup settings code
PCI / PM: Drop pme_interrupt flag from struct pci_dev
ACPI / PM: Consolidate device wakeup settings code
ACPI / PM: Drop run_wake from struct acpi_device_wakeup_flags
ACPI / sleep: EC-based wakeup from suspend-to-idle on recent systems
platform: x86: intel-hid: Wake up the system from suspend-to-idle
platform: x86: intel-vbtn: Wake up the system from suspend-to-idle
ACPI / PM: Ignore spurious SCI wakeups from suspend-to-idle
platform/x86: Add driver for ACPI INT0002 Virtual GPIO device
PCI / PM: Restore PME Enable if skipping wakeup setup
PM / sleep: Print timing information if debug is enabled
ACPI / PM: Clean up device wakeup enable/disable code
ACPI / PM: Change log level of wakeup-related message
USB / PCI / PM: Allow the PCI core to do the resume cleanup
ACPI / PM: Run wakeup notify handlers synchronously
Conflicts:
drivers/base/power/main.c
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group.
The content of sony_laptop_input_index does not change and is declared
as a static global array.
Constify spic_attribute_group and sony_laptop_input_index.
File size before:
text data bss dec hex filename
31273 5176 372 36821 8fd5 drivers/platform/x86/sony-laptop.o
File size After adding 'const':
text data bss dec hex filename
31337 5112 372 36821 8fd5 drivers/platform/x86/sony-laptop.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
[dvhart: updated commit message, includes fix suggested by Arnd Bergmann]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Using a dedicated Kconfig option for enabling debugging means the user
may be forced to recompile their kernel in order to gather debugging
information, which is inconvenient. Replace custom debugging
infrastructure with standard logging functions, taking advantage of
dynamic debug. Replace a pr_info() call inside an ACPI callback with an
acpi_handle_info() call.
The following mapping was used:
- FUJLAPTOP_DBG_ERROR -> acpi_handle_err()
- FUJLAPTOP_DBG_WARN -> acpi_handle_info() / dev_info()
- FUJLAPTOP_DBG_INFO -> acpi_handle_debug()
- FUJLAPTOP_DBG_TRACE -> acpi_handle_debug() / dev_dbg()
This means that some events which used to only be logged when the user
explicitly requested it will now be logged by default:
- ACPI method evaluation errors,
- unknown ACPI notification codes,
- unknown hotkey scancodes.
The first type of events should happen rarely, if ever at all. The rest
is interesting from driver development perspective as their presence in
the logs will mean the driver is unaware of certain events, handling of
which should be implemented.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
acpi_ns_initialize_devices(), which is called during system-wide ACPI
initialization, already detects and calls all _INI methods belonging to
objects present in ACPI tables. There is no need to call these methods
again every time the module is loaded because they only initialize
status flags and hotkey-related variables; status flags are effectively
constants, hotkey-related variables may be assigned non-zero values
before acpi_fujitsu_laptop_add() is called, but that does not really
matter as we drain the scancodes queued in the firmware's ring buffer
before doing anything else.
Remove sections of code which invoke and check evaluation status of the
_INI methods belonging to the ACPI devices handled by the driver.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Calling acpi_bus_update_power() for ACPI devices FUJ02B1 and FUJ02E3 is
pointless as they are not power manageable (neither _PS0 nor _PR0 is
defined for any of them), which causes their power state to be inherited
from their parent devices. Given the ACPI paths of these two devices
(\_SB.PCI0.LPCB.FJEX, \_SB.FEXT), their parent devices are also not
power manageable. These parent devices will thus have their power state
initialized to ACPI_STATE_D0, which in turn causes the power state for
both FUJ02B1 and FUJ02E3 to always be ACPI_STATE_D0 ("on").
Remove relevant acpi_bus_update_power() calls along with parts of debug
messages that they were supposed to have an effect on.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
In the case of brightness-related FUJ02B1 ACPI device, initializing the
input device associated with it identically as acpi-video initializes
its input device makes sense. However, using the same data for the
input device associated with the FUJ02E3 ACPI device makes little sense,
because the latter has nothing to do with video and assigning an
arbitrary product ID to it is redundant.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
No formatting is needed when setting ACPI device name and class, so
switch to using strcpy() for this purpose.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Do not check whether the pointer passed to ACPI add callbacks is NULL as
it is earlier dereferenced anyway in the bus-level probe callback,
acpi_device_probe().
Do not check the value of acpi_disabled in fujitsu_init(), because it is
already done by acpi_bus_register_driver(), which is the first function
called by fujitsu_init().
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
File size before:
text data bss dec hex filename
5396 5016 85 10497 2901 drivers/platform/x86/msi-laptop.o
File size After adding 'const':
text data bss dec hex filename
5524 4888 85 10497 2901 drivers/platform/x86/msi-laptop.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
File size before:
text data bss dec hex filename
9934 1136 2 11072 2b40 drivers/platform/x86/eeepc-laptop.o
File size After adding 'const':
text data bss dec hex filename
9998 1072 2 11072 2b40 drivers/platform/x86/eeepc-laptop.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Loongson-3 machines may have as many as 4 physical packages.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J . Hill <Steven.Hill@cavium.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16588/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
File size before:
text data bss dec hex filename
1471 528 8 2007 7d7 drivers/platform/x86/toshiba_haps.o
File size After adding 'const':
text data bss dec hex filename
1519 464 8 1991 7c7 drivers/platform/x86/toshiba_haps.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Pali recently noticed that WMI instances are zero indexed.
The only reason that these calls all worked properly is because the ASL
didn't verify the instance number.
Signed-off-by: Louis Davis <louis.davis@dell.com>
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Pali recently noticed that WMI instances are zero indexed.
The only reason that these calls all worked properly is because the ASL
didn't verify the instance number.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
The only reference to the new functions is inside of an #ifdef,
which now causes a harmless warning when CONFIG_PM_SLEEP is not set:
chrome/cros_ec_dev.c:478:12: error: 'ec_device_resume' defined but not used [-Werror=unused-function]
chrome/cros_ec_dev.c:469:12: error: 'ec_device_suspend' defined but not used [-Werror=unused-function]
This marks the two functions as __maybe_unused so they can get
silently dropped by the compiler.
Fixes: 405c84308c ("platform/chrome: cros_ec_lightbar - Control of suspend/resume lightbar sequence")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
The subset of wake-enabled host events is defined by the EC, but the EC
may still send non-wake host events if we're in the process of
suspending. Get the mask of wake-enabled host events from the EC and
filter out non-wake events to prevent spurious aborted suspend
attempts.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
When the EC is not responsive at probe, we try to get basic information
(protocol to use) later on through cros_xfer_cmd() call.
This patch makes sure there is no deadlock when re-probing the EC by
replacing call to cros_xfer_cmd() with send_command() in the function
cros_ec_get_host_command_version_mask(). Also, this patch adds the
function header indicating it must be called protected.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
With this patch, cros_ec_query_all() does not return an error if it
fails to check for MKBP events support. Instead, the EC device structure
indicates that it does not support MKBP events (mkbp_event_supported
field) and cros_ec_query_all() returns 0.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
A Mutex lock in cros_ec_cmd_xfer which may be held by frozen
Userspace thread during system suspending. So should not
call this routine in suspend thread.
Signed-off-by: Jeffery Yu <jefferyy@nvidia.com>
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Some devices might want to turn off the lightbar if e.g. the
system turns the screen off due to idleness. This prevents the
kernel from going through its normal suspend/resume pathways.
Signed-off-by: Eric Caruso <ejcaruso@chromium.org>
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Don't let EC control suspend/resume sequence. If the EC controls the
lightbar and sets the sequence when it notices the chipset transitioning
between states, we can't make exceptions for cases where we don't want
to activate the lightbar. Instead, let's move the suspend/resume
notifications into the kernel so we can selectively play the sequences.
Signed-off-by: Eric Caruso <ejcaruso@chromium.org>
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Add a program feature so we can upload and run programs for lightbar
sequences. We should be able to use this to shift sequences out of the
EC and save space there.
$ cat <suitable program bin> > /sys/devices/.../cros_ec/program
$ echo program > /sys/devices/.../cros_ec/sequence
Signed-off-by: Eric Caruso <ejcaruso@chromium.org>
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
This patch installs a notify handler to process MKBP events for EC
firmware directing them over ACPI.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
This patch removes platform_device_register() call and adds an ACPI
device id structure. The driver is now automatically probed for devices
with a GOOG0004 ACPI entry.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
This adds support for the ChromeOS LPC Microchip Embedded Controller
(mec1322) variant.
mec1322 accesses I/O region [800h, 9ffh] through embedded memory
interface (EMI) rather than LPC.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Call common functions for read / write to prepare support for future
LPC protocol variants which use different I/O ops than inb / outb.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Allow the intel-hid driver to wake up the system from suspend-to-idle
by configuring its platform device as a wakeup one by default and
switching it over to a system wakeup events triggering mode during
system suspend transitions.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Allow the intel-vbtn driver to wake up the system from suspend-to-idle
by configuring its platform device as a wakeup one by default and
switching it over to a system wakeup events triggering mode during
system suspend transitions.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Declare thermal_cooling_device_ops structure as const as it is only passed
as an argument to the function thermal_cooling_device_register and this
argument is of type const. So, declare the structure as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Declare thermal_cooling_device_ops structure as const as it is only passed
as an argument to the function thermal_cooling_device_register and this
argument is of type const. So, declare the structure as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Dell Latitude 3160 does not have keyboard backlight, but there is a
sysfs interface for it, which does nothing at all.
KBD_LED_ON_TOKEN is the only token can be found. Since it doesn't have
KBD_LED_OFF_TOKEN or KBD_LED_AUTO_*_TOKEN, it should be safe to assume
at least two tokens should be present to support keyboard backlight.
Not all models have ON token - they may have multiple AUTO tokens instead.
Models which do not use SMBIOS token to control keyboard backlight, also
have this issue. Brightness level is 0 on these models. Verified on Dell
Inspiron 3565.
Reports keyboard backlight is supported only when at least two modes are
present.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Pali Rohár found that there have some wmi query/evaluation
code that they used 'one' as the first WMI instance number.
But the number is indexed from zero that it's must less than
the instance_count in _WDG.
This patch changes those instance number from one to zero.
Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andy@infradead.org>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: "Lee, Chun-Yi" <jlee@suse.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Currently in WCOVE PMIC MFD driver, all second level IRQ chips
are chained to the respective first level IRQs. So there is no
need for explicitly unmasking the first level IRQ in this
driver. This patches removes this level 1 IRQ unmask support.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Darren Hart (VMware) <dvhart@infradead.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Lenovo Legion Y720-15IKBN is yet another Lenovo model that does not
have an hw rfkill switch, resulting in wifi always reported as hard
blocked.
Add the model to the list of models without rfkill switch.
Signed-off-by: Olle Liljenzin <olle@liljenzin.se>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Lenovo Legion Y520-15IKBN is yet another Lenovo model that does not
have an hw rfkill switch, resulting in wifi always reported as hard
blocked.
Add the model to the list of models without rfkill switch.
Signed-off-by: Olle Liljenzin <olle@liljenzin.se>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add touchscreen info for the Point of View mobii wintab p800w tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
This dumps the EC panic information from the previous reboot.
Similar to the information presented by ectool panicinfo, except
that we do not bother doing any parsing (we should write a small
offline tool for that).
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
We should output or receive every byte in the param / reply struct,
unrelated to the pointer size.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
[bleung: Picked from crosreview.com/444085 for cros_ec_debugfs.c only.
cros_ec.c upstream had a different cros_ec_sleep_event which didn't
have the sizeof issue]
Signed-off-by: Benson Leung <bleung@chromium.org>
If the EC supports the new CONSOLE_READ command type, then we
place a console_log file in debugfs for that EC device which allows
us to grab EC logs. The kernel will poll every 10 seconds for the
log and keep its own buffer, but userspace should grab this and
write it out to some logs which actually get rotated.
Signed-off-by: Eric Caruso <ejcaruso@chromium.org>
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
[bleung: restored original version of this commit, with pointer size
issue to be fixed in next commit]
Signed-off-by: Benson Leung <bleung@chromium.org>
Add cros_ec_get_event() entry point to retrieve event within functions
called by the notifier.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
intel_telemetry_debugfs:
- fix oops when load/unload module
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZQsKuAAoJEKbMaAwKp364h3AH/iwEDFtwPAzFo68U2eiFwIXy
ytkgejeb+JGEP1merD6rzaOcHROgTNEtVqLhbOAU4iU1uNCiok+1m1aVjwQRaj3s
hPG0R6zfm5/nqlXnI6ZWDqg8ZkbVrAXeGVLHWuGHna0LLozlVbxOxYAiI7E1YhpI
bsQi4hZ7L6z4Jlb25BqmkvM/de+Z9JhuHOrwVNsBdkM8xwWsdOCSH1EsawM+fP7F
p5CuBKbtKb6ADGHsiXimsIQksYnAmWfgjxR6hUvZft6h2EOp08KaIorOKDZfBE2u
oBSJT/XASHJ4o/EwjpeQiIoqnHk5lD/LbESg8PK2dFZdqhnW8fxGJWwGcL+zF+Q=
=kcZm
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.12-2' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fix from Darren Hart:
"Just a single patch to fix an oops in the intel_telemetry_debugfs
module load/unload"
* tag 'platform-drivers-x86-v4.12-2' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: intel_telemetry_debugfs: fix oops when load/unload module
Add touchscreen info for Pipo W2S tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Some peripherals on Bay Trail and Cherry Trail platforms signal a
Power Management Event (PME) to the Power Management Controller (PMC)
to wakeup the system. When this happens software needs to explicitly
clear the PME bus 0 status bit in the GPE0a_STS register to avoid an
IRQ storm on IRQ 9.
This is modelled in ACPI through the INT0002 ACPI device, which is
called a "Virtual GPIO controller" in ACPI because it defines the
event handler to call when the PME triggers through _AEI and _L02
methods as would be done for a real GPIO interrupt in ACPI.
This commit adds a driver which registers the Virtual GPIOs expected
by the DSDT on these devices, letting gpiolib-acpi claim the
virtual GPIO and install a GPIO-interrupt handler which call the _L02
handler as it would for a real GPIO controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
object_id and notify_id are in one union structure and their meaning is
defined by flags. Therefore do not print notify_id for non-event block and
do not print object_id for event block. Remove also reserved member as it
does not have any defined meaning or type yet.
As object_id and notify_id union members overlaps and have different types,
it caused that kernel print to dmesg binary data. This patch eliminates it.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Add const to rfkill_ops structures that are only passed as an argument
to the functions rfkill_alloc or samsung_new_rfkill. These arguments are
of type const, so such structures can be annotated with const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add const to rfkill_ops structure as it is only passed as an argument
to the functions rfkill_alloc. This argument is of type const,
so annotate the structure with const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add const to rfkill_ops structures that are only passed as an argument
to the functions rfkill_alloc or samsung_new_rfkill. These arguments are
of type const, so such structures can be annotated with const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add copyright statements for Andy Lutomirski and Darren Hart (VMware)
for their contributions to the WMI bus infrastructure and the creation
of the wmi-bmof driver.
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
If a machine reports a RF Button in the communication button device
bitmap, we need to remove it before calling Get Device Status otherwise
it will return the "Undefined device" (0xE2) error code.
Although this may be a BIOS bug, we don't really need to get or set the
RF Button status. The status indicator LED embedded in the button is
controlled by firmware logic, depending on the status of the wireless
radios present on the machine (WiFi || WWAN).
This commit fixes the wireless status indicator LED on the Acer
TravelMate P648-G2-MG, and cleans the following message from the kernel
log: "Get Current Device Status failed: 0xe2 - 0x0".
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Reviewed-by: "Lee, Chun-Yi" <joeyli.kernel@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The struct pcc_keyinput is not used in panasonic-laptop and in
anywhere in kernel, and it can be removed.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Acked-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The variable is used uninitialized which might come into unexpected
behaviour on some Samsung laptops.
Initialize it to 0xffff which seems a proper value for non-supported
feature.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We are trying to get rid of DRIVER_ATTR(), and the thinkpad_acpi
driver's attributes can be trivially changed to use DRIVER_ATTR_RO() and
DRIVER_ATTR_RW().
Cc: Henrique de Moraes Holschuh <ibm-acpi@hmh.eng.br>
Cc: Andy Shevchenko <andy@infradead.org>
Cc: <ibm-acpi-devel@lists.sourceforge.net>
Cc: <platform-driver-x86@vger.kernel.org>
Reviewed-by: Darren Hart (VMware) <dvhart@infradead.org>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move some initialization out of _init and into _probe.
Update signatures and logic to use the wmi bus and device structures.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
[dvhart: drop deprecated sparse_keymap_free, order declarations, add commit msg]
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-acpi@vger.kernel.org
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Many laptops (and maybe servers?) have embedded WMI Binary MOF metadata.
We do not yet have open-source tools for processing the data, although
one is in the works thanks to Pali:
https://github.com/pali/bmfdec
There is currently no interface to get the data in the first place. By
exposing it, we facilitate the development of new tools.
This is based on the original work of Andy Lutomirski <luto@kernel.org>,
but contains several modifications in response to various reviews.
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-acpi@vger.kernel.org
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
The Microsoft WMI documentation requires all data blocks to implement
the Query Control Method (WQxx). If we encounter a data block not
implementing this control method, issue a warning, and ignore the data
block. Remove the "readable" attribute as all data blocks must be
readable (query-able).
Be consistent with the language in the documentation, replace the
"writable" attribute with "setable".
Simplify (flatten) the control flow of wmi_create_device a bit while
we are updating it for the above changes.
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-acpi@vger.kernel.org
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some subdrivers need to access sibling devices. This gives them a
clean way to do so.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-acpi@vger.kernel.org
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
We already have the PNP glue to instantiate platform devices for the
ACPI devices that WMI drives. WMI should therefore attach to the
platform device, not the ACPI node.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-acpi@vger.kernel.org
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
wmi_query_block is unnecessarily indirect. Add a straightforward
method for wmi bus drivers to use to read block data.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-acpi@vger.kernel.org
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
As a platform driver, acpi_driver.notify will not be available,
so use acpi_install_notify_handler as we will be converting to a
platform driver.
This gives event drivers a simple way to handle events. It
also seems closer to what the Windows docs suggest that Windows
does: it sounds like, in Windows, the mapper is responsible for
called _WED before dispatching to the subdriver.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
[dvhart: merge two development commits and update commit message]
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-acpi@vger.kernel.org
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
At some point, we will want sub-drivers to get references to other
devices on the same WMI bus. This change is needed to avoid races.
This ends up simplifying the setup code and fixing some leaks, too.
This is based on the original work of Andy Lutomirski <luto@kernel.org>,
but includes several modifications, many in response to review from
Michał Kępień <kernel@kempniu.pl>:
https://www.spinics.net/lists/platform-driver-x86/msg08201.html
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-acpi@vger.kernel.org
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Dell XPS 13 9350 has one RW data object, one RO data object, and one
totally inaccessible data object. Check for the existence of the
accessor methods and report in sysfs.
The docs also permit WQxx getters for single-instance objects to
take no parameters. Probe for that as well to avoid ACPICA warnings
about mismatched signatures.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-acpi@vger.kernel.org
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Divide the "data", "method" and "event" types. All devices get
"instance_count" and "expensive" attributes, data and method devices get
"object_id" attributes, and event devices get "notify_id" attributes.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-acpi@vger.kernel.org
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
We have two memory leaks. If guid_already_parsed returned true, we leak
the wmi_block. If wmi_create_device failed, we leak the device.
Simplify the logic and fix both of them.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-acpi@vger.kernel.org
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
WMI is logically a bus: the WMI driver binds to an ACPI node (or
more than one), and each instance of the WMI driver enumerates its
children and hopes that drivers will attach to the children that are
useful.
This patch gives WMI a driver model bus type and the ability to
match to drivers. The bus itself is a device in the new "wmi_bus"
class, and all of the individual WMI devices are slotted into the
device hierarchy correctly.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-acpi@vger.kernel.org
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Currently we free all devices when we detach from any ACPI node.
Instead, keep track of which node WMI devices are attached to and
free them only as needed. While we are at it, match up notifications
with the device they came from correctly.
This will make our behavior more straightforward on systems with
more than one WMI node in the ACPI tables (e.g. the Dell XPS 13
9350).
This also adds a warning when GUIDs are not unique.
NB: The guid_string parameter in guid_already_parsed was a
little-endian binary GUID, not a string.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-acpi@vger.kernel.org
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Rearrange acpi_wmi_add to use Linux's error handling conventions.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-acpi@vger.kernel.org
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
We will need the device to convert to a bus architecture and bind WMI to
the platform device.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-acpi@vger.kernel.org
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Kuppuswamy Sathyanarayanan