Commit Graph

138 Commits

Author SHA1 Message Date
Bill Jordan 152e585dc9 ath9k: fix MGMT packets when using TKIP
Prevent 8 bytes from being truncated from MGMT packets
when using TKIP.

Signed-off-by: Bill Jordan <bjordan@rajant.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-24 14:41:43 -04:00
Rajkumar Manoharan 3de2111697 ath9k: Remove unused argument tsf from ath9k_hw_rxprocdesc
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-24 13:59:44 -04:00
Rajkumar Manoharan 29ab0b3632 ath9k: Re-enable RXOEL interrupt after processing rx buffers
Once RXEOL was disabled, it never be enabled again. This patch
re-enables rxeol at the end of rx tasklet.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-24 13:59:44 -04:00
Mohammed Shafi Shajakhan 6a6767b046 ath9k: remove obselete comments
the comments are obselete as the virtual wiphy support was removed from
the driver

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-10 14:07:43 -04:00
Rajkumar Manoharan e8fe733684 ath9k: Use atomic reference count for interrupt ops
Let us enable/disable interrupts based on reference count.
By doing this we can ensure that interrupts are never be
enabled in the middle of tasklet processing. Instead of
addressing corner cases like "ath9k: avoid enabling interrupts
while processing rx", this approach handles it in generic manner.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09 15:52:06 -04:00
Felix Fietkau f749b94679 ath9k: use the new channel noise value for signal strength and survey info
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08 16:04:20 -04:00
John W. Linville 41bf37117b Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem 2011-07-22 17:51:16 -04:00
Felix Fietkau 66760eac00 ath9k: improve reliability of MIC error detection
For unicast the hardware sometimes reports MIC errors even though the
frame that it received actually contains a valid MIC - on some chips this
can happen frequently enough to trigger TKIP countermeasures.
Fix this issue by not reporting MIC errors for unicast frames with a
valid key, letting mac80211 validate the MIC instead.

Additionally, strip the MIC for all frames that the hardware considers
valid to avoid wasting CPU cycles re-validating it.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-15 13:38:32 -04:00
John W. Linville 36099365c7 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
Conflicts:
	drivers/net/wireless/rtlwifi/pci.c
	include/linux/netlink.h
2011-06-24 15:25:51 -04:00
Gabor Juhos e7ef5bc079 ath9k: add fast_div_bias configuration for diversity group 1
The patch adds the missing configuration code for diversity
group 1.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22 16:09:56 -04:00
Gabor Juhos 223c5a8785 ath9k: remove superfluous parentheses
Also remove two empty lines.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22 16:09:55 -04:00
Gabor Juhos 66ce235a9d ath9k: add a missing case statement to ath_ant_div_comb_alt_check
The 'ar9003_hw_antdiv_comb_conf_get' function sets div_group to 2
however that value is not used in 'ath_ant_div_comb_alt_check'.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22 16:09:55 -04:00
Alexey Dobriyan b7f080cfe2 net: remove mm.h inclusion from netdevice.h
Remove linux/mm.h inclusion from netdevice.h -- it's unused (I've checked manually).

To prevent mm.h inclusion via other channels also extract "enum dma_data_direction"
definition into separate header. This tiny piece is what gluing netdevice.h with mm.h
via "netdevice.h => dmaengine.h => dma-mapping.h => scatterlist.h => mm.h".
Removal of mm.h from scatterlist.h was tried and was found not feasible
on most archs, so the link was cutoff earlier.

Hope people are OK with tiny include file.

Note, that mm_types.h is still dragged in, but it is a separate story.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-06-21 19:17:20 -07:00
Sujith Manoharan 5b68138e56 ath9k: Drag the driver to the year 2011
The Times They Are a-Changin'.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-19 13:54:05 -04:00
Mohammed Shafi Shajakhan 21e8ee6d20 ath9k: make sure main_rssi is positive
some times the rssi control descriptor for the main antenna may be
negative like that of alternate antenna, hence before  incrementing
packet counts/rssi of main/alternate antenna make sure both main_rssi
and alt_rssi are positive only. this avoids wrong selection of antenna
due to diversity

Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-16 14:10:47 -04:00
Mohammed Shafi Shajakhan 3e9a212a9e ath9k: configure fast_div_bias based on diversity group
configure fast diversity bias based on the antenna diversity group and
based on main/alt LNA configurations. also configure main antenna and
alternate antenna to gain-table 0 for diversity group 2(AR9485)

Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-16 14:10:47 -04:00
Mohammed Shafi Shajakhan b85c5734f0 ath9k: Implement an API to swap main/ALT LNA's
for the diversity group 2(AR9485) we swap the LNA's of main/ALT antenna
based on alternate antenna's rssi average in comparision with main
antenna's rssi, while for AR9285(antenna diversity group 0)we still
follow the older method of looking at the packet count in alternate
antenna

Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-16 14:10:46 -04:00
Mohammed Shafi Shajakhan 8afbcc8bfb ath9k_hw: define antenna diversity group
AR9285 belongs to diversity group 0 and AR9485 belongs to diversity
group 2. Based on the diversity group we configure certain antenna
diversity paramaters such as lna1_lna2_delta and fast diversity
bias values. For AR9485 we have some gain table parameter which
selects the gain table 0/1 for main and alternate antenna

Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-16 14:10:46 -04:00
Rajkumar Manoharan 2b892a98db ath9k: Fix rssi update in ad-hoc mode
The average beacon rssi which will be used by ani is not updated
in adhoc mode.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-10 15:54:53 -04:00
Rajkumar Manoharan deb751880a ath9k: avoid enabling interrupts while processing rx
The assumsion is that while processing ath9k tasklet,
interrupts were already disabled and it will be enabled
at the completion of ath9k tasklet. But whenever TSFOOR is raised,
the driver configures the beacon timers after having received a
beacon frame from the AP which inturn enables the interrupts.

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-10 15:54:45 -04:00
John W. Linville 429576b97c Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 2011-04-26 15:39:10 -04:00
Mohammed Shafi Shajakhan cedc7e3d0c ath9k: remove the unlikely check for autosleep
newer chipsets support auto sleep feature, so remove the
unlikely check which does not seems to help anything

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:19 -04:00
Sujith Manoharan 0ff2b5c05d ath9k: Fix warnings from -Wunused-but-set-variable
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25 14:50:14 -04:00
Felix Fietkau 2232d31bf1 ath9k: fix the return value of ath_stoprecv
The patch 'ath9k_hw: fix stopping rx DMA during resets' added code to detect
a condition where rx DMA was stopped, but the MAC failed to enter the idle
state. This condition requires a hardware reset, however the return value
of ath_stoprecv was 'true' in that case, which allowed it to skip the reset
when issuing a fast channel change.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Paul Stewart <pstew@google.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-19 15:22:52 -04:00
Felix Fietkau 952949738a ath9k: fix too early enabling of rx during ath_startrecv()
rx should only be enabled after enough rx buffers have been given to the
hardware, however ath_rx_buf_link was calling ath9k_hw_rxena after every
single added buffer.
Fix this by calling ath9k_hw_rxena directly from the rx tasklet after
completion instead.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-12 16:57:36 -04:00
Felix Fietkau 264bbec811 ath9k: fix PS-Poll reception on AR9160 and earlier
I can't find any valid reason for not setting the ATH9K_RX_FILTER_PSPOLL
flag on older hardware and neither the documentation nor the reference
code mention any reason for excluding older hardware here.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-12 16:57:36 -04:00
Felix Fietkau 5882da02e9 ath9k_hw: fix stopping rx DMA during resets
During PHY errors, the MAC can sometimes fail to enter an idle state on older
hardware (before AR9380) after an rx stop has been requested.

This typically shows up in the kernel log with messages like these:

ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:504 ath_stoprecv+0xcc/0xf0 [ath9k]()
Call Trace:
[<8023f0e8>] dump_stack+0x8/0x34
[<80075050>] warn_slowpath_common+0x78/0xa4
[<80075094>] warn_slowpath_null+0x18/0x24
[<80d66d60>] ath_stoprecv+0xcc/0xf0 [ath9k]
[<80d642cc>] ath_set_channel+0xbc/0x270 [ath9k]
[<80d65254>] ath_radio_disable+0x4a4/0x7fc [ath9k]

When this happens, the state that the MAC enters is easy to identify and
does not result in bogus DMA traffic, however to ensure a working state
after a channel change, the hardware should still be reset.

This patch adds detection for this specific MAC state, after which the above
warnings completely disappear in my tests.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Cc: Kyungwan Nam <Kyungwan.Nam@Atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-12 16:41:33 -04:00
Rajkumar Manoharan 99e4d43ad5 ath9k: configure beacons based on hw opmode
Current ath9k code does not handle beacon timers on opmode
specific. One such example is that a STA beacon config overwrites
already configured AP vif's beacon timers during scan.

On multi station vif case, configure beacon timers beased
on primary vif selected. This also helps while moving back
to single STA vif from multi STA vifs, where the power save
is enabled and hw has to be reconfigured with proper
beacon and bssid/aid. Otherwise connection poll will be triggered
so frequently due to beacon loss.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-07 15:49:40 -04:00
Felix Fietkau 2e286947f1 ath9k: remove support for the FIF_PROMISC_IN_BSS filter flag
The hardware rx filter flag triggered by FIF_PROMISC_IN_BSS is overly broad
and covers even frames with PHY errors. When this flag is enabled, this message
shows up frequently during scanning or hardware resets:

ath: Could not stop RX, we could be confusing the DMA engine when we start RX up

Since promiscuous mode is usually not particularly useful, yet enabled by
default by bridging (either used normally in 4-addr mode, or with hacks
for various virtualization software), we should sacrifice it for better
reliability during normal operation.

This patch leaves it enabled if there are active monitor mode interfaces, since
it's very useful for debugging.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-11 14:15:36 -05:00
Johannes Berg 6ebacbb79d mac80211: rename RX_FLAG_TSFT
The flag isn't very descriptive -- the intention
is that the driver provides a TSF timestamp at
the beginning of the MPDU -- make that clearer
by renaming the flag to RX_FLAG_MACTIME_MPDU.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-23 16:25:29 -05:00
Felix Fietkau 0d95521ea7 ath9k: use split rx buffers to get rid of order-1 skb allocations
With this change, less CPU time is spent trying to look for consecutive
pages for rx skbs. This also reduces the socket memory required for IP/UDP
reassembly.
Only two buffers per frame are supported. Frames spanning more buffers
will be dropped, but the buffer size is enough to handle the required
AMSDU size.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:44:28 -05:00
Felix Fietkau 9ac58615d9 ath9k: fold struct ath_wiphy into struct ath_softc
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:42:00 -05:00
Felix Fietkau 7545daf498 ath9k: remove support for virtual wiphys
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:41:59 -05:00
Ben Greear 4801416c76 ath9k: Fix up hardware mode and beacons with multiple vifs.
When using a mixture of AP and Station interfaces,
the hardware mode was using the type of the
last VIF registered.  Instead, we should keep track
of the number of different types of vifs and set the
mode accordingly.

In addtion, use the vif type instead of hardware opmode
when dealing with beacons.

Attempt to move some of the common setup code into smaller
methods so we can re-use it when changing vif mode as
well as adding/deleting vifs.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-19 11:36:11 -05:00
Rajkumar Manoharan d584747be8 ath9k: Fix warnings on card removal
The recently added warning message on power change failure
is not needed on device removal.

ath: Failed to wakeup in 500us
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/hw.c:1618
ath9k_hw_setpower+0x61f/0x630 [ath9k_hw]()
Hardware name: 64756D6
Pid: 540, comm: kworker/u:3 Not tainted 2.6.37-rc6-wl #37
Call Trace:
 [<ffffffff810501aa>] warn_slowpath_common+0x7a/0xb0
 [<ffffffffa056e280>] ? ath9k_iowrite32+0x0/0x90 [ath9k]
 [<ffffffff810501f5>] warn_slowpath_null+0x15/0x20
 [<ffffffffa05226ef>] ath9k_hw_setpower+0x61f/0x630 [ath9k_hw]
 [<ffffffffa05700e5>] ath9k_ps_wakeup+0x85/0xd0 [ath9k]
 [<ffffffffa0570685>] ath9k_configure_filter+0x25/0x80 [ath9k]
 [<ffffffffa04dde43>] ieee80211_configure_filter+0x133/0x190 [mac80211]
 [<ffffffffa04ee502>] ieee80211_do_stop+0x132/0x540 [mac80211]
 [<ffffffff813466ff>] ? _raw_spin_unlock_bh+0x1f/0x30
 [<ffffffff812b6923>] ? dev_deactivate+0x1c3/0x1e0
 [<ffffffffa04ee925>] ieee80211_stop+0x15/0x20 [mac80211]
 [<ffffffff8129d1b6>] __dev_close+0x56/0x90

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-22 15:43:25 -05:00
John W. Linville 393934c6b5 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
Conflicts:
	drivers/net/wireless/ath/ath9k/ath9k.h
	drivers/net/wireless/ath/ath9k/main.c
	drivers/net/wireless/ath/ath9k/xmit.c
2010-12-08 16:23:31 -05:00
Mohammed Shafi Shajakhan cae6b74d90 ath9k: Remove dead code in recv.c
The structure struct ieee80211_rx_status *rxs is no longer needed to be
passed to ath_rx_send_to_mac80211 function

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07 17:08:09 -05:00
Mohammed Shafi Shajakhan aaef24b4c9 ath9k: Properly use unlikely check macro
AUTOSLEEP feature is enabled only for AR9271 and AR9003 version
chipsets.So unlikely macro should be used only to check whether
auto-sleep feature is enabled

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07 17:08:08 -05:00
Ben Greear d7fd1b50a5 ath9k: Make DMA warning in ath_stoprecv WARN_ON_ONCE.
This decreases spammage in the log.  A single line message
will still be printed, so users can be aware that problem
exists.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07 16:54:24 -05:00
Joe Perches 226afe68fd ath: Convert ath_print to ath_dbg
Remove ath/debug.h and the includes of these files.
Coalesce long formats.
Correct a few misspellings and missing "\n"s from these logging messages.
Remove unnecessary trailing space before a newline.
Remove ARRAY_SIZE casts, use printf type %zu

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07 16:34:48 -05:00
Joe Perches 3800276a40 ath: Convert ath_print(.., ATH_DBG_FATAL to ath_err
So these errors are always emitted at KERN_ERR level.
Remove ARRAY_SIZE casts, use printf type %zu

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07 16:34:47 -05:00
Senthil Balasubramanian 38852b20c8 ath9k: Fix STA disconnect issue due to received MIC failed bcast frames
AR_RxKeyIdxValid will not be set for bcast/mcast frames and so relying
this status for MIC failed frames is buggy.

Due to this, MIC failure events for broadcast frames are not sent to
supplicant resulted in AP disconnecting the STA.

Able to pass Wifi Test case 5.2.18 with this fix.

Cc: Stable <stable@kernel.org> (2.6.36+)
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07 14:57:05 -05:00
John W. Linville d89197c7f3 Revert "ath9k: Fix STA disconnect issue due to received MIC failed bcast frames"
This reverts commit 916448e77f.

"As far as I can tell, either of these patches breaks multiple VIF
scenarios.  I'm not sure exactly why, but I had to revert this to
get any of my interfaces to associate."
  -- Ben Greear <greearb@candelatech.com>

http://marc.info/?l=linux-wireless&m=129123368719339&w=2

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-02 14:10:58 -05:00
Senthil Balasubramanian 916448e77f ath9k: Fix STA disconnect issue due to received MIC failed bcast frames
AR_RxKeyIdxValid will not be set for bcast/mcast frames and so relying
this status for MIC failed frames is buggy.

Due to this, MIC failure events for broadcast frames are not sent to
supplicant resulted in AP disconnecting the STA.

Able to pass Wifi Test case 5.2.18 with this fix.

Cc: Stable <stable@kernel.org> (2.6.36+)
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-30 13:45:02 -05:00
John W. Linville d7a066c923 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 2010-11-24 16:19:24 -05:00
Felix Fietkau d47844a014 ath9k: fix timeout on stopping rx dma
It seems that using ath9k_hw_stoppcurecv to stop rx dma is not enough.
When it's time to stop DMA, the PCU is still busy, so the rx enable
bit never clears.
Using ath9k_hw_abortpcurecv helps with getting rx stopped much faster,
with this change, I cannot reproduce the rx stop related WARN_ON anymore.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:19:31 -05:00
Luis R. Rodriguez 4bdd1e978e ath9k: move the PCU lock to the sc structure
The PCU lock should be used to contend TX DMA as well,
this will be done next.

This is part of a series of patches which fix stopping
TX DMA completley when requested on the driver.
For more details about this issue refer to this thread:

http://marc.info/?l=linux-wireless&m=128629803703756&w=2

Tested-by:  Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:24:46 -05:00
Luis R. Rodriguez 78a7685e1e ath9k: add a debug warning when we cannot stop RX
We have seen several DMA races when we race against
stopping and starting the PCU. I suspect that when
we cannot stop the PCU we may hit some of these same
races so warn against them for now but only when
debugging (CONFIG_ATH_DEBUG) is enabled.

If you run into this warning and are a developer,
please fix the cause of the warning. The potential
here, although I cannot prove yet, is that the DMA
engine can be confused and start writing to a buffer
that was already DMA'd before and at least the kernel
assumes is not being accessed by hardware anymore.

Cc: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:24:18 -05:00
Felix Fietkau 9fa23e1741 ath9k: optimize/fix ANI RSSI processing
ANI needs the RSSI average only in station mode, and only for tracking
the signal strength of beacons of the AP that it is connected to.
Adjust the code to track on the beacon RSSI, and store the average of that
in the ath_wiphy struct.
With these changes, we can get rid of this extra station lookup in the
rx path, which saves precious CPU cycles.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-09 16:13:24 -05:00
Rajkumar Manoharan 5f841b4130 ath9k: Avoid HW opmode overridden on monitor mode changes
The HW opmode is blindly set to monitor type on monitor mode
change notification. This overrides the opmode when one of the
interfaces is still running as non-monitor iftype. So the monitoring
information needs to be maintained seperately.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-08 16:53:46 -05:00