As is done on OMAP3, check omap_uart_can_sleep() as one of the
pre-conditions for entering the idle loop. Without this check,
entering idle introduces large latencies on active UARTs, and is
especially noticable on serial console.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some modules which have 16bit registers can cause imprecise
aborts if a __raw_readl/writel is used to read/write 32 bits.
Add an additional flag to identify modules which have such
hard requirement, and handle it in the hwmod framework.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Inorder to avoid any assumptions from bootloader, the watchdog
timer module is reset during init. This enables the watchdog
timer.
Therefore, it is required to disable WDT after it is reset
during init. Otherwise the system would reboot as per the default
watchdog timer registers settings.
Later, when the watchdog driver is loaded, the watchdog timer settings
is adjusted as per the default timer_margin set in the driver and the
driver would supports the normal operations supported by OMAP watchdog
timer.
Signed-off-by: Charulatha V <charu@ti.com>
Reported-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
VMMC2 regulator is configured but it's not used for the IGEP v2, so
remove this regulator from board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add i2c eeprom driver to access monitor EDID binary information
from user space, something that is required by 'decode-edid' and
'parse-edid'.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are currently two versions of IGEP v2 board, this patch introduces a
function to detect the hardware revision of IGEP board.
--------------------------
| Id. | Hw Rev. | GPIO 28 |
--------------------------
| 0 | B/C | high |
| 1 | C | low |
--------------------------
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IGEP v2 board has four leds, this patch allows control all
of these LEDs using the LED class if CONFIG_LEDS_GPIO is selected
or using the General Purpose Input/Output (GPIO) interface if
CONFIG_LEDS_GPIO is not selected.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO for various devices are missing from the board initialization.
This patch adds support for the VBUS and over current gpios. Without this
patch, input/outputs from these two sources are ignored.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP3 IGEP module is a low-power, high performance production-ready
system-on-module (SOM) based on TI's OMAP3 family. More about this
board at www.igep.es.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
[tony@atomide.com: updated for the mmc changes and to be selected by default]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The keypad matrix variable declaration is not matching
with structure variable keymap declared in keypad_matrix.h.
Due to this, following sparse warnings are generated with omap3_defconfig.
arch/arm/mach-omap2/board-devkit8000.c:223:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-devkit8000.c:223:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-devkit8000.c:223:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-ldp.c:107:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-ldp.c:107:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-ldp.c:107:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-omap3evm.c:472:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-omap3evm.c:472:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-omap3evm.c:472:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-3430sdp.c:114:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-3430sdp.c:114:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-3430sdp.c:114:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-rx51-peripherals.c:248:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-rx51-peripherals.c:248:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-rx51-peripherals.c:248:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-zoom-peripherals.c:88:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-zoom-peripherals.c:88:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-zoom-peripherals.c:88:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-cm-t35.c:568:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-cm-t35.c:568:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-cm-t35.c:568:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-omap3stalker.c:415:13: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-omap3stalker.c:415:13: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-omap3stalker.c:415:13: got int static [toplevel] *<noident>
This patch modifies the variable keymap declaration as per declaration in matrix_keymap structure.
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-input@vger.kernel.org
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes sparse warnings due non declarations of static functions.
arch/arm/plat-omap/sram.c:130:13: warning: symbol 'omap_detect_sram' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:216:13: warning: symbol 'omap_map_sram' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:450:12: warning: symbol 'omap_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:348:12: warning: symbol 'omap242x_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:369:12: warning: symbol 'omap243x_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:425:12: warning: symbol 'omap34xx_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:441:12: warning: symbol 'omap44xx_sram_init' was not declared. Should it be static
arch/arm/plat-omap/mcbsp.c:36:6: warning: symbol 'omap_mcbsp_write' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:50:5: warning: symbol 'omap_mcbsp_read' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:65:6: warning: symbol 'omap_mcbsp_st_write' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:70:5: warning: symbol 'omap_mcbsp_st_read' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:1648:15: warning: symbol 'omap_st_add' was not declared. Should it be static?
arch/arm/plat-omap/fb.c:414:15: warning: symbol 'omapfb_reserve_sram' was not declared. Should it be static?
arch/arm/plat-omap/cpu-omap.c:43:5: warning: symbol 'omap_verify_speed' was not declared. Should it be static?
arch/arm/plat-omap/cpu-omap.c:61:14: warning: symbol 'omap_getspeed' was not declared. Should it be static?
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes miscellaneous sparse warnings in mach-omap2.
arch/arm/mach-omap2/board-am3517evm.c:141:17: warning: Initializer entry defined twice
arch/arm/mach-omap2/board-am3517evm.c:142:18: also defined here
arch/arm/mach-omap2/irq.c:50:35: warning: Using plain integer as NULL pointer
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes sparse warnings due non declarations of static functions.
arch/arm/mach-omap2/timer-gp.c:115:12: warning: symbol 'omap2_gp_clockevent_set_gptimer' was not declared. Should it be static?
arch/arm/mach-omap2/powerdomain.c:993:5: warning: symbol 'pwrdm_set_lowpwrstchange' was not declared. Should it be static?
arch/arm/mach-omap2/board-flash.c:141:8: warning: symbol 'board_nand_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-n8x0.c:416:6: warning: symbol 'n8x0_mmc_slot1_cover_handler' was not declared. Should it be static?
arch/arm/mach-omap2/board-n8x0.c:544:13: warning: symbol 'n8x0_mmc_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-peripherals.c:902:13: warning: symbol 'rx51_peripherals_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-video.c:107:13: warning: symbol 'rx51_video_mem_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-debugboard.c:155:12: warning: symbol 'zoom_debugboard_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-peripherals.c:280:13: warning: symbol 'zoom_peripherals_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-igep0020.c:110:13: warning: symbol 'igep2_flash_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-am3517evm.c:109:6: warning: symbol 'am3517_evm_ethernet_init' was not declared. Should it be static?
drivers/mtd/onenand/omap2.c:577:5: warning: symbol 'omap2_onenand_rephase' was not declared. Should it be static?
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes sparse warnings due to non declaration of
static structures and variables.
Sparse warning logs fixed:
arch/arm/mach-omap2/control.c:88:6: warning: symbol 'omap3_secure_ram_storage' was not declared. Should it be static?
n
arch/arm/mach-omap2/timer-gp.c:50:22: warning: symbol 'gptimer_wakeup' was not declared. Should it be static?
arch/arm/mach-omap2/timer-gp.c:240:18: warning: symbol 'omap_timer' was not declared. Should it be static?
arch/arm/mach-omap2/prcm.c:121:24: warning: symbol 'prcm_context' was not declared. Should it be static?
arch/arm/mach-omap2/mux2420.c:510:29: warning: symbol 'omap2420_pop_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux2430.c:589:29: warning: symbol 'omap2430_pop_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:934:28: warning: symbol 'omap3_cus_subset' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1080:29: warning: symbol 'omap3_cus_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1272:28: warning: symbol 'omap3_cbb_subset' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1393:29: warning: symbol 'omap3_cbb_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1603:28: warning: symbol 'omap36xx_cbp_subset' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1821:29: warning: symbol 'omap36xx_cbp_ball' was not declared. Should it be static?
arch/arm/mach-omap2/pm-debug.c:165:15: warning: symbol 'pm_dbg_dir' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3evm.c:587:30: warning: symbol 'ads7846_config' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3evm.c:606:23: warning: symbol 'omap3evm_spi_board_info' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-sdram.c:46:25: warning: symbol 'rx51_sdrc_params' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-sdram.c:211:25: warning: symbol 'rx51_get_sdram_timings' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3touchbook.c:64:15: warning: symbol 'touchbook_revision' was not declared. Should it be static?
arch/arm/mach-omap2/board-am3517evm.c:350:24: warning: symbol 'am3517_evm_dss_device' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3stalker.c:567:23: warning: symbol 'omap3stalker_spi_board_info' was not declared. Should it be static?
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise tidspbridge cannot work.
It looks like this was dropped in the conversion to staging. I took the
liberty of doing some cleaning up.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch "omap: zoom: add mmc3/wl1271 device support" in the
wireless tree still uses .wires in struct omap2_hsmmc_info.
.wires has now been replaced with .caps in patch "omap: mmc:
extended to pass host capabilities from board file" in the
OMAP tree.
This causes linux-next as of 20101001 build to break as
below. Fix this.
CC arch/arm/mach-omap2/board-zoom-peripherals.o
arch/arm/mach-omap2/board-zoom-peripherals.c:217: error: unknown field 'wires' specified in initializer
make[1]: *** [arch/arm/mach-omap2/board-zoom-peripherals.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
A patch from Sukumar Ghorai <s-ghorai@ti.com> changed the
nwires to use caps instead. However, nwires is still
needed for the earlier controller.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Upcoming ASoC multi-component and OMAP hwmod changes will conflict
in arch/arm/mach-omap2/devices.c. Avoid this by moving a little bit
include statement introduced by ASoC Multi-Component Support patch.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
VMALLOC_END is supposed to be an absolute value, while PAGE_OFFSET may
vary depending on the selected user:kernel memory split mode through
CONFIG_VMSPLIT_*. In fact, the goal of moving PAGE_OFFSET down is to
accommodate more directly addressed RAM by the kernel below the vmalloc
area, and having VMALLOC_END move along PAGE_OFFSET is rather against
the very reason why PAGE_OFFSET can be moved in the first place.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
On OMAP4, MMC2 controller has eMMC which draws power from VAUX regulator
on TWL. Though the eMMC supports dual voltage[1.8v/3v] as per ocr register,
its VCC is fixed at 3V for operation. With this once the mmc core selects
the minimum voltage[1.8] supported based on the ocr value read from OCR register,
eMMC will not get detected. Thus the platform data for MMC2 is updated with ocr
mask and same will be communicated to core which will set the regulator to
always operate at 3V when ever turned ON.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In OMAP4, as per new PM programming model, the legacy registers
which were there in OMAP3 are all shifted by 0x100 while new one's
are added from offset 0 to 0x10.
For OMAP4, the register offset appending of 0x100 done in devices.c
currently, is moved to driver file.This change fits in for current
implementation as well as once the driver undergoes hwmod adaptation.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Avoid possible crash if CONFIG_MMC_OMAP_HS is not set
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap4 es2 hsmmc has a updated soft reset logic.After the
reset is issued monitor a 0->1 transition first. The reset of
CMD or DATA lines is complete only after a 0->1->0 transition
of SRC or SRD bits.
Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Tested-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform data to make use of newly added charging driver.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Instead of enabling the wifi module explicitly using GPIO, add a fixed
regulator and hook it to MMC host card power control. This way it will
only be enabled when SDIO subsystem wants to talk to it, saving power
(as done by Zoom boards).
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The existing definitions for cpu revision used
upper nibble in the bits[15:08]. With OMAP3630,
definitions use lower nibble.
This patch unifies the definitions to start
at lower nibble.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since 6cdee91257 the references to
enable_off_mode and sleep_while_idle can't be resolved when CONFIG_PM_DEBUG
isn't set:
arch/arm/mach-omap2/built-in.o: In function `omap_uart_restore_context':
arch/arm/mach-omap2/serial.c:253: undefined reference to `enable_off_mode'
arch/arm/mach-omap2/built-in.o: In function `omap3_can_sleep':
arch/arm/mach-omap2/pm34xx.c:479: undefined reference to `sleep_while_idle'
Simply #define these in pm.h just like omap2_pm_debug.
Signed-off-by: Loïc Minier <loic.minier@linaro.org>
[khilman: moved down into existing #ifdef section]
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
When checking how to program the next powerstate for the PER
powerdomain, the next state of PER powerdomain was written twice.
Remove the duplicate write.
Reported-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Initialize all omap-uarts for zoom boards. Now zoom_peripheral_init
will initialise all uarts for 3630. 3630sdp_board_init call
zoom_peripheral_init so we can now remove serial_init from 3630sdp
board init as zoom_peripheral_init now will do that the same.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Enable omap-serial driver in /mach-omap2/Kconfig and
move 8250 driver selection for zoom boards. With omap-serial
driver addition all omap-uarts can be handled with
omap-serial driver.
With addition of omap-serial driver console parameter
needs be changed in bootargs from ttyS* should be
replaced with ttyO* [O --> OMAP not ZERO]
For example: ttyS0[UART1 on 3430SDP] changes to ttyO0.
But with some boards that do not use omap-uart as console uart.
we need to handle them with 8250 driver. Ex: ZOOM2/3.
For zoom2/3 board we need to use 8250 serial driver and
console parameter will remain ttyS0 which basically uses
a Quad uart placed on the debug board connected through a
gpio line.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch makes the following:
- Adds missing wakeup padding register handling.
- Fixes a hardcode to use PER module ONLY on UART3.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add prepare idle and resume idle call for uart4 used by 3630.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
To standarize among other uarts (1 to 3), we shall now:
- Enable uart4 autodile bit.
- Enable uart4 wakeup in PER.
- Allow uart4 to wakeup the MPU.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This is only valid for omap 36xx family of chips.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Since the UART enable/idle is done during the idle path (with
interrupts disabled), use the non-locking versions of the hwmod
enable/idle functions.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Since the omap_device for UART is currently managed inside the idle
path itself, don't let the bus-level code suspend/resume the UART.
To prevent this, pm_runtime_get() is used when preparing for suspend
and pm_runtime_put() is used when finished with suspend.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Remove set_uart_globals function as this will not be needed as
physical address for uarts will be taken from hwmod data file.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Major rework of OMAP UART init for omap_device conversion as well as
use with either 8250 driver or new omap-serial driver.
In preparation for a new omap-serial driver, remove 8250 assumptions
and dependencies from the serial core.
Convert UART core and PM support to use omap_device layer. Also add
support for both console on 8250 or omap-serial driver.
omap_device conversion:
- Convert clock API calls to omap_device calls
- Remove all static platform_data setup and configuration. This is
all done by the omap_device build phase.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds omap_hwmod data for UARTs on OMAP2 and OMAP3
platforms.
UART4 support for 3630 and OMAP2 hwmod data added by Govindraj R.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add uart1-4 hwmod data into omap4_hwmod data file.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch splits omap_init_wdt() into separate omap_init_wdt()
functions under mach-omap1 and mach-omap2 and set them up with
subsys_initcall.
Also it uses omap_device_build() API instead of
platform_device_register() for watchdog timer device registration
for OMAP2plus chips.
For OMAP2plus chips, the device specific data defined in centralized
hwmod database will be used.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add watchdog timer hwmod data for OMAP4 chip
Note: wd_timer3 in enabled in the hwmod list but it is
not yet supported by the watchdog driver.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add watchdog timer hwmod data for OMAP2430 chip
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add watchdog timer hwmod data for OMAP2420 chip
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add watchdog timer hwmod data for OMAP3 chip
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Enable SMSC911x Ethernet driver for LogicPD's OMAP
3530 LV SOM and OMAP 35x Torpedo board.
Signed-off-by: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Introduce of a generic way to setup smsc911x based Ethernet
controller connected to GPMC similar to gpmc-smc91x but without
timing setup.
Signed-off-by: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add low-level initialization for hsmmc controller for
LogicPD's OMAP 3530 LV SOM and OMAP 35x Torpedo board.
Signed-off-by: Tim Nordell <tim.nordell@logicpd.com>
[tony@atomide.com: updated for the recent mmc platform init changes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding support for LogicPD's OMAP 3530 LV SOM and
OMAP 35x Torpedo board.
Signed-off-by: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Unnecessary cast from void* in assignment.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
add support for hsusb host ports 1, 2 and on-module usb hub.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When changing the L3 clock frequency, the CPU is executing from internal RAM
and the SDRC clock is disabled. During this time accesses made to external
DDR are stalled. If the ARM subsystem attempts to access the DDR while the
SDRC clock is disabled this will stall the CPU until the access to the SDRC
timeouts. A timeout on the SDRC should never occur. Once a timeout occurs all
the following accesses will be aborted and the DDR is no longer accessible.
Although the code being executed in the internal RAM does not directly access
the DDR, it was found that the branch prediction logic in the CPU may cause
the CPU to prefetch code from a DDR location while the SDRC clock is disabled.
This was causing an SDRC timeout which resulted in a system hang.
This patch fixes this problem by ensuring the branch prediction logic is
disabled while changing the L3 clock frequency. The branch prediction logic
is disabled by clearing the Z-bit in the ARM CTRL register.
Disabling the branch prediction logic does not have any noticable impact
on the execution time of this code section. The hardware observability
signals were used to monitor the sdrc idle time with and without this
patch when operating at different CPU frequencies (150MHz, 500MHz and
600MHz) and the total sdrc idle time when changing frequenct was in
the range of 9-11us. This was measured on an omap3430 SDP running the
omapzoom p-android-omap-2.6.29 branch.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
This patch has multiple fixes together. To ensure that git bisect work across
commits, all changes are clubbed together
1. Move the common control base address to control core
2. Remove the manually coeded defines and use the ones from headers.
3. Fix the the status register define in id.c for OMAP4
4. Fix all the register define in hsmmc.c
5. Use the control pad accessor API for omap4 hsmmc register accesses
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4, control module is divided into 4 separate IPs
- OMAP44XX_CTRL_MODULE_CORE
- OMAP44XX_CTRL_MODULE_PAD_CORE
- OMAP44XX_CTRL_MODULE_WKUP
- OMAP44XX_CTRL_MODULE_PAD_WKUP
This patch adds all the omap4 control module register data and
includes them in the common control.h
The register data is autogenerated from the codebase thanks
to Benoit Cousson efforts
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4 control pad are not addressable from control
core base. So the common omap_ctrl_read/write APIs breaks
Hence export separate APIs to manage the omap4 pad control
registers.
This APIs will work only for OMAP4
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On omap4 control module is divided in four IP blocks.
- CTRL_MODULE_CORE 0x4a002000
- CTRL_MODULE_PAD_CORE 0x4a100000
- CTRL_MODULE_WKUP 0x4a30c000
- CTRL_MODULE_PAD_WKUP 0x4a31e000
Addressing all the modules with single base address is not possible
considering 16 bit offsets. The mux code manages the pad core and pad
wakeup related base address inside the mux framework. For other usage
only control core and control pad bases are necessary. So this patch
maps only needed pad control base address which is used by device drivers
and infrastructure code
The main control core base is still kept same in this patch to
keep git-bisect working. This will be fixed in the relevant patch
in this series.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Fix a few OMAP4430 clock tree problems after the recent manual merge of the
various ES2 clock patches:
- usim optional clock and its parent had the same name, rename the parent
usim_fclk -> usim_ck
- OPTFCLKEN_CLK32K is not handled anymore by the USBPHYOCP2SCP module in ES2
Create a new clock that belongs to CM_ALWON_USBPHY_CLKCTRL register
This patch depends on some of the PRCM macro updates from Rajendra.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: tweaked patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
DSS on ES2 supports only OSWR, hence remove the support
for CSWR from the powerdomain framework.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
4430 ES2 has a few new registers added and a few modified
from ES1. This patch adds all the register changes in PRM
and CM for OMAP4430 ES2.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
This patch updates the PRM and CM register bitshifts and masks
for OMAP4430 ES2.0.
Replace as well the BITFIELD macro with the shift operator in order
to be consistent with the previous OMAP2 & 3 format.
Sort the register list in comments in order to have a consistent
register order and avoid futur change during code generation.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
OMAP4 IP optional clocks require explicit enable in module CTRLCLK
register. In order to allow that we have to create artificial clock
nodes that represent this clock inputs in the IP.
Notes:
- Temporary use OMAP3 names for GPIO optional clocks until the GPIO hwmod
convertion is done. It will enforce the usage of OMAP4 names as the reference.
- Temporary use OMAP3 names for TIMER main clock (gptX_fck) until TIMER hwmod
convertion is done. During that convertion, the new name will have to be used.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
The OMAP4 hwmod data introduced the new naming convention for TI
IPs (See patch OMAP4: hwmod: Add partial hwmod support for OMAP4430 ES1.0)
The leaf clock names are using the same IP name and thus must be
modified to match the clock populated in the hwmod data.
- Fix some leaf clocks nodes that were using a _iclk instead of the _fclk
prefix.
- Fix some wrong interface clock name for master IPs connected to
interconnect.
Please not that due to the fact that nodes are sorted by name, the name
change will introduce a quite ugly diff a little bit hard to follow.
Timers clock con_id is still using the old gptX_fck name until the
gptimer driver is updated to omap_device framework.
Timers entries in hwmods DB are still disabled until the migration
if timer to platform_driver + omap_hwmod.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: manually resolved conflicts with Rajendra's clock patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
This patch updates the clock tree with all the
changes in OMAP4430 ES2.
clock nodes added
-1- tie_low_clock_ck
-2- abe_dpll_bypass_clk_mux_ck
clock nodes deleted
-1- dpll_sys_ref_clk
-2- per_sgx_fclk
-3- usbphyocp2scp_ick
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
[paul@pwsan.com: added comment re ES1 clocks to top of file]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
wires variable is renamed, extended and this single variable to be used to
pass the platform capabilities, e.g DDR mode. Also removed the hardcoded
value was using as bus-width.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This 'legacy' OMAP2420 McBSP2 muxing code is currently broken after recent
conversion to new mux code. The omap_mcbsp_request calling this code is
usually called after booting whereas the omap_mux_init_signal is __init
marked so null pointer dereference would occur.
Fix this by removing the muxing code and let the bootloader or board file to
do it if necessary. Remove also omap2_mcbsp_ops as there is no use for it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Updates to enable omap aes
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@nokia.com>
[tony@atomide.com: updated to use CONFIG_ARCH_OMAP2/3 instead of old 24XX/34XX]
Signed-off-by: Tony Lindgren <tony@atomide.com>
At Pandaboard we have 2 status leds, so adding them with similar usage as
we have for Beagleboard (heartbeat and mmc0). The patch basically adds the
platform data required by leds-gpio driver.
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@canonical.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap 4430sdp board support for the proximity sensor via GPIO keys.
The proximity sensor is connected to GPIO and is registered as a
GPIO key.
- Making the default state of the sensor off at bootup
- The init is called before platform_add_devices
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ASoC Multi-Component Support moves some code from sound/soc/omap/zoom2.c into
arch/arm/mach-omap2/board-zoom2.c. However, that code should go to
board-zoom-peripherals.c instead as there is common code and registration
for zoom boards.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Cc: Lopez Cruz, Misael <x0052729@ti.com>
Cc: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
ASoC Multi-Component Support patch removes #if 0 in board-zoom2.c that was
used to protect some uncompiling dead code. Remove that code as it seems to
be here quite some time since commit 479f12c.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Tested-by: Misael Lopez Cruz <misael.lopez@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
OMAP USBOTG module has a requirement to set the autoidle bit only after
setting smartidle bit. Modified the _sys_enable api to set the smartidle
first and then the autoidle bit. Setting this will not have any impact on the
other modules.
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Partha Basak <p-basak2@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The omap4_cm_wait_module_ready function would only check for
the modules to be completely functional before declaring them
ready to be accessed.
There might also be instances where in the module is actually
in idle (under h/w control) but should still be declared
accessible, as the h/w control would make it functional when
needed.
Hence make omap4_cm_wait_module_ready return true in case
the module is fully functional *or* in idle state.
Fail only if the module is fully disabled or stuck intransition.
The explaination from the TRM for the idlest bits on OMAP4 is as
below for quick reference
Module idle state:
0x0 func: Module is fully functional, including OCP
0x1 trans: Module is performing transition: wakeup, or sleep, or sleep
abortion
0x2 idle: Module is in Idle mode (only OCP part). It is functional if
using separate functional clock
0x3 disabled: Module is disabled and cannot be accessed
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch removes davinci architecture code that has now been rendered
useless by the previous patches in the MDIO separation series.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds mdio platform devices on SoCs that have the necessary
hardware. Clock lookup entries (aliases) have also been added, so that the
MDIO and EMAC drivers can independently enable/disable a shared underlying
clock. Further, the EMAC MMR region has been split down into separate MDIO
and EMAC regions.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On ES2.0 the L2 cache init parameter ineeds to be changed to take
care of cache size. The cache size is 1MB on ES2.0 vs 512KB on ES1.0
This patch fixes the init parameter to update the same using
dynamic cpu version check
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This patch updates the id.c and cpu.h files to support
omap4 ES2.0 silicon detection. Few initial omap4 es2 samples
IDCODE is same as es1. So the patch uses ARM cpuid register to
detect the ES version for such samples
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Bootloader on Nokia N800 and N810 muxes I2C codec port pins for EAC block.
As there is no driver and use for EAC, mux those pins for McBSP instead
since N810 ASoC drivers can use it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Second i2c bus on Nokia N800 and N810 shares both common and hw specific
peripherals. Register now this bus and add board info with tlv320aic3x for
N810. Common peripherals may be added as an additional board info to
omap_register_i2c_bus(2, ...);
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Move n8x0_i2c_board_info_1 out from #ifdef CONFIG_MENELAUS block,
register i2c1 in n8x0_init_machine and do a few clean-ups around these.
Code looks better if board infos are grouped together
- Mark n8x0_i2c_board_info_1 and n8x0_menelaus_platform_data with __initdata
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes these compiler warnings:
CC arch/arm/mach-omap2/mux.o
arch/arm/mach-omap2/mux.c: In function 'omap_mux_init_gpio':
arch/arm/mach-omap2/mux.c:90: warning: 'gpio_mux' may be used uninitial
ized in this function
CC arch/arm/plat-omap/gpio.o
arch/arm/plat-omap/gpio.c: In function 'omap2_gpio_resume_after_idle':
arch/arm/plat-omap/gpio.c:2152: warning: 'l' may be used uninitialized
in this function
arch/arm/plat-omap/gpio.c: In function 'omap2_gpio_prepare_for_idle':
arch/arm/plat-omap/gpio.c:2085: warning: 'l2' may be used uninitialized
in this function
arch/arm/plat-omap/gpio.c:2085: warning: 'l1' may be used uninitialized
in this function
CC arch/arm/mach-omap2/board-omap4panda.o
arch/arm/mach-omap2/board-omap4panda.c: In function 'omap4_panda_init':
arch/arm/mach-omap2/board-omap4panda.c:277: warning: unused variable 's
tatus'
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding i2c eeprom driver to access monitor EDID binary information
from user space, something that is required by 'decode-edid' and
'parse-edid'.
BugLink: https://bugs.launchpad.net/bugs/608279
Signed-off-by: Mathieu Poirier <mathieu.poirier@canonical.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap3630 based BeagleBoard xM uses a MicroSD card slot with
no write protection.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Kevin Hilman