If the interface is a bridge or Open vSwitch port, and we can't
forward a packet because it exceeds the local PMTU estimate,
trigger an ICMP or ICMPv6 reply to the sender, using the same
interface to forward it back.
If metadata collection is enabled, set destination and source
addresses for the flow as if we were receiving the packet, so that
Open vSwitch can match the ICMP error against the existing
association.
v2: Use netif_is_any_bridge_port() (David Ahern)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's currently possible to bridge Ethernet tunnels carrying IP
packets directly to external interfaces without assigning them
addresses and routes on the bridged network itself: this is the case
for UDP tunnels bridged with a standard bridge or by Open vSwitch.
PMTU discovery is currently broken with those configurations, because
the encapsulation effectively decreases the MTU of the link, and
while we are able to account for this using PMTU discovery on the
lower layer, we don't have a way to relay ICMP or ICMPv6 messages
needed by the sender, because we don't have valid routes to it.
On the other hand, as a tunnel endpoint, we can't fragment packets
as a general approach: this is for instance clearly forbidden for
VXLAN by RFC 7348, section 4.3:
VTEPs MUST NOT fragment VXLAN packets. Intermediate routers may
fragment encapsulated VXLAN packets due to the larger frame size.
The destination VTEP MAY silently discard such VXLAN fragments.
The same paragraph recommends that the MTU over the physical network
accomodates for encapsulations, but this isn't a practical option for
complex topologies, especially for typical Open vSwitch use cases.
Further, it states that:
Other techniques like Path MTU discovery (see [RFC1191] and
[RFC1981]) MAY be used to address this requirement as well.
Now, PMTU discovery already works for routed interfaces, we get
route exceptions created by the encapsulation device as they receive
ICMP Fragmentation Needed and ICMPv6 Packet Too Big messages, and
we already rebuild those messages with the appropriate MTU and route
them back to the sender.
Add the missing bits for bridged cases:
- checks in skb_tunnel_check_pmtu() to understand if it's appropriate
to trigger a reply according to RFC 1122 section 3.2.2 for ICMP and
RFC 4443 section 2.4 for ICMPv6. This function is already called by
UDP tunnels
- a new function generating those ICMP or ICMPv6 replies. We can't
reuse icmp_send() and icmp6_send() as we don't see the sender as a
valid destination. This doesn't need to be generic, as we don't
cover any other type of ICMP errors given that we only provide an
encapsulation function to the sender
While at it, make the MTU check in skb_tunnel_check_pmtu() accurate:
we might receive GSO buffers here, and the passed headroom already
includes the inner MAC length, so we don't have to account for it
a second time (that would imply three MAC headers on the wire, but
there are just two).
This issue became visible while bridging IPv6 packets with 4500 bytes
of payload over GENEVE using IPv4 with a PMTU of 4000. Given the 50
bytes of encapsulation headroom, we would advertise MTU as 3950, and
we would reject fragmented IPv6 datagrams of 3958 bytes size on the
wire. We're exclusively dealing with network MTU here, though, so we
could get Ethernet frames up to 3964 octets in that case.
v2:
- moved skb_tunnel_check_pmtu() to ip_tunnel_core.c (David Ahern)
- split IPv4/IPv6 functions (David Ahern)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
geneve_nl2info() sets 'df' conditionally, so we have to
initialize it by copying the value from existing geneve
device in geneve_changelink().
Fixes: 56c09de347 ("geneve: allow changing DF behavior after creation")
Reported-by: syzbot+7ebc2e088af5e4c0c9fa@syzkaller.appspotmail.com
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cater to devices which:
(a) may want to sleep in the callbacks;
(b) only have IPv4 support;
(c) need all the programming to happen while the netdev is up.
Drivers attach UDP tunnel offload info struct to their netdevs,
where they declare how many UDP ports of various tunnel types
they support. Core takes care of tracking which ports to offload.
Use a fixed-size array since this matches what almost all drivers
do, and avoids a complexity and uncertainty around memory allocations
in an atomic context.
Make sure that tunnel drivers don't try to replay the ports when
new NIC netdev is registered. Automatic replays would mess up
reference counting, and will be removed completely once all drivers
are converted.
v4:
- use a #define NULL to avoid build issues with CONFIG_INET=n.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new structure geneve_config and moves the per-device
configuration attributes to it, like we already have in VXLAN with
struct vxlan_config. This ends up being pretty invasive since those
attributes are used everywhere.
This allows us to clean up the argument lists for geneve_configure (4
arguments instead of 8) and geneve_nl2info (5 instead of 9).
This also reduces the copy-paste of code setting those attributes
between geneve_configure and geneve_changelink to a single memcpy,
which would have avoided the bug fixed in commit
56c09de347 ("geneve: allow changing DF behavior after creation").
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, trying to change the DF parameter of a geneve device does
nothing:
# ip -d link show geneve1
14: geneve1: <snip>
link/ether <snip>
geneve id 1 remote 10.0.0.1 ttl auto df set dstport 6081 <snip>
# ip link set geneve1 type geneve id 1 df unset
# ip -d link show geneve1
14: geneve1: <snip>
link/ether <snip>
geneve id 1 remote 10.0.0.1 ttl auto df set dstport 6081 <snip>
We just need to update the value in geneve_changelink.
Fixes: a025fb5f49 ("geneve: Allow configuration of DF behaviour")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the geneve interface is in collect_md (external) mode, it can't send any
packets submitted directly to its net interface, as such packets won't have
metadata attached. This is expected.
However, the kernel itself sends some packets to the interface, most
notably, IPv6 DAD, IPv6 multicast listener reports, etc. This is not wrong,
as tunnel metadata can be specified in routing table (although technically,
that has never worked for IPv6, but hopefully will be fixed eventually) and
then the interface must correctly participate in IPv6 housekeeping.
The problem is that any such attempt increases the tx_error counter. Just
bringing up a geneve interface with IPv6 enabled is enough to see a number
of tx_errors. That causes confusion among users, prompting them to find
a network error where there is none.
Change the counter used to tx_dropped. That better conveys the meaning
(there's nothing wrong going on, just some packets are getting dropped) and
hopefully will make admins panic less.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IFLA_GENEVE_* attributes are in the data array, which is correctly
used when fetching the value, but not when setting the extended
ack. Because IFLA_GENEVE_MAX < IFLA_MAX, we avoid out of bounds
array accesses, but we don't provide a pointer to the invalid
attribute to userspace.
Fixes: a025fb5f49 ("geneve: Allow configuration of DF behaviour")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The debug check must be done after unregister_netdevice_many() call --
the list_del() for this is done inside .ndo_stop.
Fixes: 2843a25348 ("geneve: speedup geneve tunnels dismantle")
Reported-and-tested-by: <syzbot+68a8ed58e3d17c700de5@syzkaller.appspotmail.com>
Cc: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
ipv6_stub uses the ip6_dst_lookup function to allow other modules to
perform IPv6 lookups. However, this function skips the XFRM layer
entirely.
All users of ipv6_stub->ip6_dst_lookup use ip_route_output_flow (via the
ip_route_output_key and ip_route_output helpers) for their IPv4 lookups,
which calls xfrm_lookup_route(). This patch fixes this inconsistent
behavior by switching the stub to ip6_dst_lookup_flow, which also calls
xfrm_lookup_route().
This requires some changes in all the callers, as these two functions
take different arguments and have different return types.
Fixes: 5f81bd2e5d ("ipv6: export a stub for IPv6 symbols used by vxlan")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
IN_MULTICAST's primary intent is as a uapi macro.
Elsewhere in the kernel we use ipv4_is_multicast consistently.
This patch unifies linux's multicast checks to use that function
rather than this macro.
Signed-off-by: Dave Taht <dave.taht@gmail.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit a07966447f ("geneve: ICMP error lookup handler") I wrongly
assumed buffers from icmp_socket_deliver() would be linear. This is not
the case: icmp_socket_deliver() only guarantees we have 8 bytes of linear
data.
Eric fixed this same issue for fou and fou6 in commits 26fc181e6c
("fou, fou6: do not assume linear skbs") and 5355ed6388 ("fou, fou6:
avoid uninit-value in gue_err() and gue6_err()").
Use pskb_may_pull() instead of checking skb->len, and take into account
the fact we later access the GENEVE header with udp_hdr(), so we also
need to sum skb_transport_header() here.
Reported-by: Guillaume Nault <gnault@redhat.com>
Fixes: a07966447f ("geneve: ICMP error lookup handler")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of stubs is growing and has nothing to do with addrconf.
Move the definition of the stubs to a separate header file and update
users. In the move, drop the vxlan specific comment before ipv6_stub.
Code move only; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the definition of the default Geneve udp port from the geneve
source to the header file, so we can re-use it from drivers.
Modify existing drivers to use it.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Cc: John Hurley <john.hurley@netronome.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When IPv6 is compiled but disabled at runtime, geneve_sock_add returns
-EAFNOSUPPORT. For metadata based tunnels, this causes failure of the whole
operation of bringing up the tunnel.
Ignore failure of IPv6 socket creation for metadata based tunnels caused by
IPv6 not being available.
This is the same fix as what commit d074bf9600 ("vxlan: correctly handle
ipv6.disable module parameter") is doing for vxlan.
Note there's also commit c0a47e44c0 ("geneve: should not call rt6_lookup()
when ipv6 was disabled") which fixes a similar issue but for regular
tunnels, while this patch is needed for metadata based tunnels.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we add a new GENEVE device with IPv6 remote, checking only for
IS_ENABLED(CONFIG_IPV6) is not enough as we may disable IPv6 in the
kernel command line (ipv6.disable=1), and calling rt6_lookup() would
cause a NULL pointer dereference.
v2:
- don't mix declarations and code (reported by Stefano Brivio, Eric Dumazet)
- there's no need to use in6_dev_get() as we only need to check that
idev exists (reported by David Ahern). This is under RTNL, so we can
simply use __in6_dev_get() instead (Stefano, Eric).
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: c40e89fd35 ("geneve: configure MTU based on a lower device")
Cc: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns:
drivers/net/geneve.c:428:29: error: suggest braces around initialization
of subobject [-Werror,-Wmissing-braces]
struct in6_addr addr6 = { 0 };
^
{}
Rather than trying to appease the various compilers that support the
kernel, use memset, which is unambiguous.
Fixes: a07966447f ("geneve: ICMP error lookup handler")
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
draft-ietf-nvo3-geneve-08 says:
It is strongly RECOMMENDED that Path MTU Discovery ([RFC1191],
[RFC1981]) be used by setting the DF bit in the IP header when Geneve
packets are transmitted over IPv4 (this is the default with IPv6).
Now that ICMP error handling is working for GENEVE, we can comply with
this recommendation.
Make this configurable, though, to avoid breaking existing setups. By
default, DF won't be set. It can be set or inherited from inner IPv4
packets. If it's configured to be inherited and we are encapsulating IPv6,
it will be set.
This only applies to non-lwt tunnels: if an external control plane is
used, tunnel key will still control the DF flag.
v2:
- DF behaviour configuration only applies for non-lwt tunnels, apply DF
setting only if (!geneve->collect_md) in geneve_xmit_skb()
(Stephen Hemminger)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export an encap_err_lookup() operation to match an ICMP error against a
valid VNI.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack arg to rtnl_create_link and add messages for invalid
number of Tx or Rx queues.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched/cls_api.c has overlapping changes to a call to
nlmsg_parse(), one (from 'net') added rtm_tca_policy instead of NULL
to the 5th argument, and another (from 'net-next') added cb->extack
instead of NULL to the 6th argument.
net/ipv4/ipmr_base.c is a case of a bug fix in 'net' being done to
code which moved (to mr_table_dump)) in 'net-next'. Thanks to David
Ahern for the heads up.
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't abuse exceptions: if the destination MTU is already higher
than what we're transmitting, no exception should be created.
Fixes: 52a589d51f ("geneve: update skb dst pmtu on tx path")
Fixes: a93bf0ff44 ("vxlan: update skb dst pmtu on tx path")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f15ca723c1 ("net: don't call update_pmtu unconditionally") avoids
that we try updating PMTU for a non-existent destination, but didn't clean
up cases where the check was already explicit. Drop those redundant checks.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Michal remaind, we should allow to clear ttl inherit. Then we will
have three states:
1. set the flag, and do ttl inherit.
2. do not set the flag, use configured ttl value, or default ttl (0) if
not set.
3. disable ttl inherit, use previous configured ttl value, or default ttl (0).
Fixes: 52d0d404d3 ("geneve: add ttl inherit support")
CC: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar with commit 72f6d71e49 ("vxlan: add ttl inherit support"),
currently ttl == 0 means "use whatever default value" on geneve instead
of inherit inner ttl. To respect compatibility with old behavior, let's
add a new IFLA_GENEVE_TTL_INHERIT for geneve ttl inherit support.
Reported-by: Jianlin Shi <jishi@redhat.com>
Suggested-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple overlapping changes in stmmac driver.
Adjust skb_gro_flush_final_remcsum function signature to make GRO list
changes in net-next, as per Stephen Rothwell's example merge
resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the addition of GRO for ESP, gro_receive can consume the skb and
return -EINPROGRESS. In that case, the lower layer GRO handler cannot
touch the skb anymore.
Commit 5f114163f2 ("net: Add a skb_gro_flush_final helper.") converted
some of the gro_receive handlers that can lead to ESP's gro_receive so
that they wouldn't access the skb when -EINPROGRESS is returned, but
missed other spots, mainly in tunneling protocols.
This patch finishes the conversion to using skb_gro_flush_final(), and
adds a new helper, skb_gro_flush_final_remcsum(), used in VXLAN and
GUE.
Fixes: 5f114163f2 ("net: Add a skb_gro_flush_final helper.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the tunnel option type stored in tunnel flags when creating options
for tunnels. Thereby ensuring we do not set geneve, vxlan or erspan tunnel
options on interfaces that are not associated with them.
Make sure all users of the infrastructure set correct flags, for the BPF
helper we have to set all bits to keep backward compatibility.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manage pending per-NAPI GRO packets via list_head.
Return an SKB pointer from the GRO receive handlers. When GRO receive
handlers return non-NULL, it means that this SKB needs to be completed
at this time and removed from the NAPI queue.
Several operations are greatly simplified by this transformation,
especially timing out the oldest SKB in the list when gro_count
exceeds MAX_GRO_SKBS, and napi_gro_flush() which walks the queue
in reverse order.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, on a new link creation or when 'remote' address parameter
is updated, an MTU is not changed and always equals 1500. When a lower
device has a larger MTU, it might not be efficient, e.g. for UDP, and
requires the manual MTU adjustments to match the MTU of the lower
device.
This patch tries to automate this process, finds a lower device using
the 'remote' address parameter, then uses its MTU to tune GENEVE's MTU:
* on a new link creation
* when 'remote' parameter is changed
Also with this patch, the MTU from a user, on a new link creation, is
passed to geneve_change_mtu() where it is verified, and MTU adjustments
with a lower device is skipped in that case. Prior that change, it was
possible to set the invalid MTU values on a new link creation.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
geneve_change_mtu() will be used not only as ndo_change_mtu() callback,
but also to verify a user specified MTU on a new link creation in the
next patch.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ETH_HLEN instead and introduce two new macros: GENEVE_IPV4_HLEN
and GENEVE_IPV6_HLEN that include Ethernet header length, corresponded
IP header length and GENEVE_BASE_HLEN.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some dst_ops (e.g. md_dst_ops)) doesn't set this handler. It may result to:
"BUG: unable to handle kernel NULL pointer dereference at (null)"
Let's add a helper to check if update_pmtu is available before calling it.
Fixes: 52a589d51f ("geneve: update skb dst pmtu on tx path")
Fixes: a93bf0ff44 ("vxlan: update skb dst pmtu on tx path")
CC: Roman Kapl <code@rkapl.cz>
CC: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a93bf0ff44 ("vxlan: update skb dst pmtu on tx path") has fixed
a performance issue caused by the change of lower dev's mtu for vxlan.
The same thing needs to be done for geneve as well.
Note that geneve cannot adjust it's mtu according to lower dev's mtu
when creating it. The performance is very low later when netperfing
over it without fixing the mtu manually. This patch could also avoid
this issue.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we now hold RTNL lock in geneve_exit_net, it's better batch them
to speedup geneve tunnel dismantle.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano pointed that configure or show UDP_ZERO_CSUM6_RX/TX info doesn't
make sense if we haven't enabled CONFIG_IPV6. Fix it by adding
if IS_ENABLED(CONFIG_IPV6) check.
Fixes: abe492b4f5 ("geneve: UDP checksum configuration via netlink")
Fixes: fd7eafd021 ("geneve: fix fill_info when link down")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
geneve->sock4/6 were added with geneve_open and released with geneve_stop.
So when geneve link down, we will not able to show remote address and
checksum info after commit 11387fe4a9 ("geneve: fix fill_info when using
collect_metadata").
Fix this by avoid passing *_REMOTE{,6} for COLLECT_METADATA since they are
mutually exclusive, and always show UDP_ZERO_CSUM6_RX info.
Fixes: 11387fe4a9 ("geneve: fix fill_info when using collect_metadata")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be sure that sock_list initialized in net_init hook was return
to initial state.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were quite a few overlapping sets of changes here.
Daniel's bug fix for off-by-ones in the new BPF branch instructions,
along with the added allowances for "data_end > ptr + x" forms
collided with the metadata additions.
Along with those three changes came veritifer test cases, which in
their final form I tried to group together properly. If I had just
trimmed GIT's conflict tags as-is, this would have split up the
meta tests unnecessarily.
In the socketmap code, a set of preemption disabling changes
overlapped with the rename of bpf_compute_data_end() to
bpf_compute_data_pointers().
Changes were made to the mv88e6060.c driver set addr method
which got removed in net-next.
The hyperv transport socket layer had a locking change in 'net'
which overlapped with a change of socket state macro usage
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to re-invent memchr_inv() with !is_all_zero(). While at
it, replace conditional and return clauses with a single return
clause in is_tnl_info_zero().
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On big-endian machines, functions converting between tunnel ID
and VNI use the three LSBs of tunnel ID storage to map VNI.
The comparison function eq_tun_id_and_vni(), on the other hand,
attempted to map the VNI from the three MSBs. Fix it by using
the same check implemented on LE, which maps VNI from the three
LSBs of tunnel ID.
Fixes: 2e0b26e103 ("geneve: Optimize geneve device lookup.")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack error messages for failure paths while creating/modifying
geneve devices. Once extack support is added to iproute2, more
meaningful and helpful error messages will be displayed making it easy
for users to discern what went wrong.
Before:
=======
$ ip link add gen1 address 0:1:2:3:4:5:6 type geneve id 200 \
remote 192.168.13.2
RTNETLINK answers: Invalid argument
After:
======
$ ip link add gen1 address 0:1:2:3:4:5:6 type geneve id 200 \
remote 192.168.13.2
Error: Provided link layer address is not Ethernet
Also, netdev_dbg() calls used to log errors associated with Netlink
request have been removed.
Signed-off-by: Girish Moodalbail <girish.moodalbail@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mainline had UFO fixes, but UFO is removed in net-next so we
take the HEAD hunks.
Minor context conflict in bcmsysport statistics bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Brivio