Add i2c shutdown function to prevent the pop sound of the headphone while
the system is rebooting or shutdowning. It de-initials the jack detection
function, and it cannot be turned off in _BIAS_OFF. If we don't de-initial
it, the pop sound will be heard in the situation of powering off. And
replace the related register settings from magic number to meaningful
defined name.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the InvenSense ICS-43432 I2S MEMS microphone.
This is a non-software-configurable MEMS microphone with I2S output.
Tested on a setup with a single ICS-43432 (the device itself supports
stereo operation using a hardware pin controlling left vs. right channel
output).
Signed-off-by: Ricard Wanderlof <ricardw@axis.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set buffer bytes step constraint to 128. A matching constraint has
already been set to period size. This helps PCM setup to tolerate ALSA
clients that set the PCM hw params in unusual order.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In theory, the device may get suspended even at runtime PM suspend.
Currently we don't save the mixer state for autopm, and it may bring
inconsistency.
This patch removes the special handling for autosuspend.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After the recent fix of runtime PM for USB-audio driver, we got a
lockdep warning like:
=============================================
[ INFO: possible recursive locking detected ]
4.2.0-rc8+ #61 Not tainted
---------------------------------------------
pulseaudio/980 is trying to acquire lock:
(&chip->shutdown_rwsem){.+.+.+}, at: [<ffffffffa0355dac>] snd_usb_autoresume+0x1d/0x52 [snd_usb_audio]
but task is already holding lock:
(&chip->shutdown_rwsem){.+.+.+}, at: [<ffffffffa0355dac>] snd_usb_autoresume+0x1d/0x52 [snd_usb_audio]
This comes from snd_usb_autoresume() invoking down_read() and it's
used in a nested way. Although it's basically safe, per se (as these
are read locks), it's better to reduce such spurious warnings.
The read lock is needed to guarantee the execution of "shutdown"
(cleanup at disconnection) task after all concurrent tasks are
finished. This can be implemented in another better way.
Also, the current check of chip->in_pm isn't good enough for
protecting the racy execution of multiple auto-resumes.
This patch rewrites the logic of snd_usb_autoresume() & co; namely,
- The recursive call of autopm is avoided by the new refcount,
chip->active. The chip->in_pm flag is removed accordingly.
- Instead of rwsem, another refcount, chip->usage_count, is introduced
for tracking the period to delay the shutdown procedure. At
the last clear of this refcount, wake_up() to the shutdown waiter is
called.
- The shutdown flag is replaced with shutdown atomic count; this is
for reducing the lock.
- Two new helpers are introduced to simplify the management of these
refcounts; snd_usb_lock_shutdown() increases the usage_count, checks
the shutdown state, and does autoresume. snd_usb_unlock_shutdown()
does the opposite. Most of mixer and other codes just need this,
and simply returns an error if it receives an error from lock.
Fixes: 9003ebb13f ('ALSA: usb-audio: Fix runtime PM unbalance')
Reported-and-tested-by: Alexnader Kuleshov <kuleshovmail@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The variable pcm can be never NULL since it was rewritten with
list_for_each_entry().
Suggested-by: Markus Osterhoff <linux-kernel@k-raum.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/soc/rockchip/rockchip_rt5645.c:214:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/rockchip/rockchip_max98090.c:225:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Being careless, judge the return value of snd_soc_card_jack_new
is opposite, so it should be fixed.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When snd_hdac_refresh_widget_sysfs() is called before the first
hda_widget_sysfs_init(), the next call overrides and eventually
fails. This results in unexpected Oops, something like:
BUG: unable to handle kernel NULL pointer dereference at 00000000000000c8
IP: [<ffffffff8180e2a3>] hdmi_chmap_ctl_info+0x23/0x40
The fix is to add a check of the existing sysfs tree. Also, for more
safety, this patch adds the checks of device_is_registered() in
snd-hdac_refresh_wdiget_sysfs(), too.
Fixes: fa4f18b4f4 ('ALSA: hda - Refresh widgets sysfs at probing Haswell+ HDMI codecs')
Bugizlla: https://bugzilla.kernel.org/show_bug.cgi?id=103431
Reported-by: Andreas Reis <andreas.reis@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The extcon driver takes the DAPM mutex from within the interrupt thread
in several places, which makes it possible to get into a situation where
the interrupt thread is blocked waiting on the DAPM mutex whilst a DAPM
sequence is running which is attempting to configure the FLL. In this
case the FLL completion can't be completed as as the IRQ handler is
ONE_SHOT, which cause the FLL lock to use the full time out (250mS) and
report that the process timed out.
It is not really practical to make the extcon driver not take the DAPM
mutex from within the interrupt thread, at least not without extensive
modification. So this patch fixes the issue by switching the wait for
the FLL lock to polling. A few fast polls are done first as the FLL
should lock quickly for a good quality reference clock, (indeed it hits
on the first poll on my system) and it will poll every 20mS after that
until it times out.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The patch removes the incorrect setting of the JD mode. It will cause pop
sound in the booting time.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch corrects the sequence of the jack detection. It will prevent the
pop sound while the jack plug in.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the original calibration function and modify the depop and
calibration function to prevent the pop sound in the booting time.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Added rt5677_spi_read() and refactored rt5677_spi_write() so that
an arbitrary block in the DSP address space can be read/written
via SPI. For example, this allows us to load an ELF DSP firmware
with sparse sections, and stream audio samples from DSP ring buffer.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Acked-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Otherwise it triggers a compile warning like:
sound/ppc/keywest.c:104:1: warning: data definition has no type or storage class
sound/ppc/keywest.c:104:1: error: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE' [-Werror=implicit-int]
Fixes: a2bc2af66a ('ALSA: ppc: keywest: Export I2C module alias information')
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix below build warning:
CC [M] sound/soc/tegra/tegra20_spdif.o
sound/soc/tegra/tegra20_spdif.c: In function 'tegra20_spdif_platform_remove':
sound/soc/tegra/tegra20_spdif.c:361:24: warning: unused variable 'spdif' [-Wunused-variable]
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_ioremap_resource() instead of open code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_ioremap_resource() instead of open code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/cs4349.c:389:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Tim Howe <tim.howe@cirrus.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the commit [fa4f18b4f402: ALSA: hda - Refresh widgets sysfs at
probing Haswell+ HDMI codecs], snd_hdac_refresh_widget_sysfs() is
explicitly called in the codec driver. But this results in refreshing
twice, as snd_hdac_refresh_widget_sysfs() itself calls
snd_hdac_refresh_widgets() function.
Instead, we can replace the call in snd_hda_codec_update_widgets()
with snd_hdac_refresh_widget_sysfs(). This also fixes the missing
sysfs update for ca0132, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The widget power-saving code tries to turn up/down the power of each
widget in the I/O paths that are modified at each jack plug/unplug.
The recent report revealed that the power activation leaves some
widgets unpowered after plugging. This is because
snd_hda_activate_path() turns on path->active flag at the end of the
function while the path power management is done before that. Then
it's regarded as if nothing is active, and the driver turns off the
power.
The fix is simply to set the flag at the beginning of the function,
before trying to power up.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=102521
Cc: <stable@vger.kernel.org> [v4.1+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The is_active_nid_for_any() function in the generic parser is supposed
to check all connections from/to the given widget, but the current
code checks only the first input connection (index = 0).
This patch corrects the code to check all inputs by passing -1 to
index argument.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=102521
Cc: <stable@vger.kernel.org> [v4.1+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After a for-loop was replaced by list_for_each_entry, see
Commit bbbc7e8502 ("ALSA: hda - Allocate hda_pcm objects dynamically"),
Commit 751e221689 ("ALSA: hda: fix possible null dereference"),
a possible NULL pointer dereference has been introduced; this patch adds
the NULL check on pcm->pcm, while leaving a potentially superfluous
check on pcm itself untouched.
Signed-off-by: Markus Osterhoff <linux-kernel@k-raum.org>
Cc: <stable@vger.kernel.org> #v4.1+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a helper to find the stream using stream tag and direction.
This is useful for drivers to query stream based on stream tag
and direction, fox example while downloading FW thru DSP loader
code
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
spbmaxfifo API is actually a query function not a set function so
name it snd_hdac_ext_stream_get_spbmaxfifo()
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While creating hdac_ext_device, we used hdev for sizeof insteadof
edev, which resulted in eventual crash of the system Fix the size
here
Fixes: a512f56116 ('ALSA: hdac: add hdac extended device')
Reported-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
card->shortname is a 32 char string so the sprintf() can theoretically
overflow. snd_rawmidi_new() can accept strings up to 64 bytes long.
I have made the temporay buf[] array 40 bytes long and changed the
sprintf() to snprintf().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow vendor drivers to define bespoke bytes ext handlers and IDs for
TLV bytes controls. And the topology core will bind these handlers by
matching IDs defined by the vendor driver and user space topology
data file.
And TLV callback binding is moved to soc_tplg_kcontrol_bind_io(). This
function process all handler binding now.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the pointer of struct soc_tplg as one argument, so no need to
pass standard/vendor specific kcontrol handlers and their count.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Vendor specific handlers should override standard handlers. So we can
handle things in the order from specific to generic.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
hdac_ext_stream assign doesn't require key mapping as in case of
hdac_stream. So for host stream, the key to device mapping needs
to be removed.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The drivers need to set the spib and maxfifios values, so add
these new APIs snd_hdac_ext_stream_set_spib() and
snd_hdac_ext_stream_set_spbmaxfifo() APIs
For these APIs we also need to have spib and fifos pointer, so
add these to hdac_ext_stream and initialize them at stream init
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
New HDA controllers like Skylake sport multiple HDA links, so we need a
helper to turn off all the links in one go while suspending the device so
add snd_hdac_ext_bus_link_power_down_all() API
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SPCAP and Mutilink register offset were incorrect as offset needs
to be based on capability offset. So correct the offset for
read/write of spcap/link register.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert the ac97_bus from legacy suspend/resume callbacks to dev_pm_ops.
Since there isn't anything special to do at the bus level the bus driver
does not have to implement any callbacks. The device driver core will
automatically pick up and execute the device's PM ops.
As there is only a single AC'97 driver implementing suspend and resume,
update both the core and driver at the same time to avoid unnecessary code
churn.
While we are at it also drop the ifdefs around the suspend/resume functions
to increase compile test coverage.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set the card owner field to prevent the module from being removed from
underneath its users.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel Haswell (and later) codec refreshes the widgets tree to expose
the whole widget nodes at probing. However, this refresh was missing
for sysfs tree.
This patch adds the missing piece, as we have now a proper API.
Reported-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I believe this probably cannot happen, as the code suggests. There
would have to be an kcontrol->index.id which was zero, otherwise this
would be prevented in snd_ctl_find_id(). But snd_BUG_ON() is just a
WARN() or a no-op so static checkers complain that we keep on going with
a negative offset. Let's just handle the error as well as printing
a warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some codecs like Intel HDMI by default do not show up all the pins, they
have to be manually enabled, so we need to refresh the codec widgets and
then recreate the sysfs tree. So add new API snd_hdac_refresh_widget_sysfs()
to do this. It should be be used by codec driver after sending magic verbs
to codec
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds new extended driver objects and API for registering the
extended devices.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds based hdac extended device object which will be used by
ASoC HDAC codecs
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HDAC extended device objects are created by HDAC extended bus on probe.
When controller is removed they should be removed as well, so add API
snd_hdac_ext_bus_device_remove for this
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On shutdown/reboot of CX20722, first shut down all EAPDs, then
shut down the afg node to D3.
Failure to do so can lead to spurious noises from the internal speaker
directly after reboot (and before the codec is reinitialized again, i e
in BIOS setup or GRUB menus).
BugLink: https://bugs.launchpad.net/bugs/1487345
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds native DSD support for the Gustard DAC-X20U.
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If there don't exist dynamic sink or source widget, it will failed to
add dynamic path.
"AIF3ADCDAT" is snd_soc_dapm_aif_out, can't be dynamic sink widget. So
change the audio route to fix this issue.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no use of snd_soc_unregister_card in remove function
as devm_snd_soc_register_card in probe function automatically
handles it. So, remove use of snd_soc_unregister_card and with
this change remove arndale_audio_remove as it is now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The topology code merged in the v4.2 merge window introduced a new ABI
which was believed to be suitable for use but subsequently additional
work by the developers of this feature have revealed some problems that
need to be addressed. In order to allow this to be done without having
to support the initial ABI add Kconfig to disable the build and also add
some #error statements to the UAPI header so users can't use them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJV1K6xAAoJECTWi3JdVIfQl60H/Aiq3smUvb+npgLI402pdzZ8
eaGVSw1oGO7NFylBDu8FeiJLBvl4ZQmSfMbaLBJ50JPKqY1nFjOXFk0nWatQ8TPY
0aB1NKCIGNNCWXTO3ABZ8zeT5AH218n3t8tTUxWzOS1RhpZMwePVuS83+cdwfxAZ
He29rX2xfKFaGo92NMB707vU6aobYC0jc4pIaVoYLN7E49leTSzgGKKNVW2JyEog
d44Zd7jEXPY1lj166sEEF4axAzGc2ZkwsbmOmymbszEBkYtDVs1Q1omFf+CNi31Y
16bLwOVzTXVM7PeheRF2Tp6qtcyDpQhLicfBjakkJ1X5MtW3OzoutGli/isIh2g=
=Gj9l
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.2-disable-topology' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Disable topology support for v4.2
The topology code merged in the v4.2 merge window introduced a new ABI
which was believed to be suitable for use but subsequently additional
work by the developers of this feature have revealed some problems that
need to be addressed. In order to allow this to be done without having
to support the initial ABI add Kconfig to disable the build and also add
some #error statements to the UAPI header so users can't use them.
The wrong register was used to set the gain of ref loop, when changing
the FLL output on an active FLL. This patch corrects the offset of the
gain register.
Signed-off-by: Nikesh Oswal <Nikesh.Oswal@wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The input terminal parser recurses into the referenced clock entity to verify
it is existant and thus the terminal descriptor is valid. The actual property
values of the term instance which is initially parsed must not be overriden by
the recursion. For this to work the term properties have to be assigned after
recursing into the referenced clock entity descriptors.
Signed-off-by: Julian Scheel <julian@jusst.de>
Acked-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove use of snd_soc_unregister_component in remove function
as devm_snd_soc_register_component in probe function automatically
handles it.
Also, convert call of snd_dmaengine_pcm_register to managed resource
function devm_snd_dmaengine_pcm_register and remove usage of
snd_dmaengine_pcm_unregister in probe and remove functions.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The fix for deadlock in PM in commit [1ee23fe07ee8: ALSA: usb-audio:
Fix deadlocks at resuming] introduced a new check of in_pm flag.
However, the brainless patch author evaluated it in a wrong way
(logical AND instead of logical OR), thus usb_autopm_get_interface()
is wrongly called at probing, leading to unbalance of runtime PM
refcount.
This patch fixes it by correcting the logic.
Reported-by: Hans Yang <hansy@nvidia.com>
Fixes: 1ee23fe07e ('ALSA: usb-audio: Fix deadlocks at resuming')
Cc: <stable@vger.kernel.org> [v3.15+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Revert the problematic part of commit 470805eb9f ("ASoC: tegra:
Convert to managed resources"). Before this commit, PM cleanup was
performed after the component was unregistered. But returning
directly will skip PM cleanup. So, to be on safe side it is better
to use snd_soc_register_component instead of
devm_snd_soc_register_component.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
regmap_readable() returns false if map->format.format_write is set.
For .reg_bits = 7, .val_bits = 9, setting,
map->format.format_write = regmap_format_7_9_write;
Even current code has implemented map->readable_reg, regmap_readable()
still returns false anyway. Thus drop the misleading readable_reg callback
implementation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow the topology code to be compiled out so that users who don't need
topology don't need to havve the code compiled in, saving them some
memory.
Some more configuration could be added to remove some of the hooks into
the core data structures but that is probably best done with some
refactoring to use functions to do the updates of the data structures
rather than ifdefing in the code as we'd need to do at the minute.
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use resource managed function devm_snd_soc_register_component for
component registration instead of snd_soc_register_component.
Also, remove davinci_vcif_remove as it is now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DAPM core already creates widgets for DAIs. It is not necessary
to declare them by SND_SOC_DAPM_AIF_IN/SND_SOC_DAPM_AIF_OUT.
Furthermore, original codes use backend DAI's stream name to be the AIF
widget name. It causes the same widget to be created twice, and after
commit 92fa124267 ("ASoC: dapm: Add new widgets to the end of the
widget list") the first created widget (by snd_soc_dapm_new_controls)
is used, not the 2nd created one (by snd_soc_dapm_new_dai_widgets),
so audio path is broken.
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The power states in a proc file are printed in a racy manner on a
single static string buffer. Fix it by calling snd_iprintf() directly
for each state instead of processing on a temporary buffer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Many arrays in hda_proc.c are string arrays that should be covered by
const prefix for increasing the safety and reducing the size.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few helper functions to convert the pin information to strings have
been exported with assumption that they were used by other drivers.
But they are referred only in the proc interface in the end.
Let's make them local so that we can get rid of a few exports.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The M-Audio Transit exposes an interface with a SYNC_NONE attribute.
This is not a valid value according to the USB audio classspec. However
there is a sync endpoint associated to this record. Changing the logic to
try to use this sync endpoint allows for seamless transitions between
altset 2 and altset 3. If any errors happen, the behavior remains the same.
$ more /proc/asound/card1/stream0
M-Audio Transit USB at usb-0000:00:14.0-2, full speed : USB Audio
Playback:
Status: Stop
Interface 1
Altset 1
Format: S24_3LE
Channels: 2
Endpoint: 3 OUT (ADAPTIVE)
Rates: 48001 - 96000 (continuous)
Interface 1
Altset 2
Format: S24_3LE
Channels: 2
Endpoint: 3 OUT (NONE)
Rates: 8000 - 48000 (continuous)
Interface 1
Altset 3
Format: S16_LE
Channels: 2
Endpoint: 3 OUT (ASYNC)
Rates: 8000 - 48000 (continuous)
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a transition occurs between alternate settings that do not use the
same synchronization method, the substream pointers were not reset.
This prevents audio from being played during the second transition.
Identified and tested with M-Audio Transit device
(0763:2006 Midiman M-Audio Transit)
Details of the issue:
First playback to adaptive endpoint:
$ aplay -Dhw:1,0 ~/24_96.wav
Playing WAVE '/home/plb/24_96.wav' : Signed 24 bit Little Endian in 3bytes,
Rate 96000 Hz, Stereo
[ 3169.297556] usb 1-2: setting usb interface 1:1
[ 3169.297568] usb 1-2: Creating new playback data endpoint #3
[ 3169.298563] usb 1-2: Setting params for ep #3 (type 0, 3 urbs), ret=0
[ 3169.298574] usb 1-2: Starting data EP @ffff880035fc8000
first playback to asynchronous endpoint:
$ aplay -Dhw:1,0 ~/16_48.wav
Playing WAVE '/home/plb/16_48.wav' : Signed 16 bit Little Endian,
Rate 48000 Hz, Stereo
[ 3204.520251] usb 1-2: setting usb interface 1:3
[ 3204.520264] usb 1-2: Creating new playback data endpoint #3
[ 3204.520272] usb 1-2: Creating new capture sync endpoint #83
[ 3204.521162] usb 1-2: Setting params for ep #3 (type 0, 4 urbs), ret=0
[ 3204.521177] usb 1-2: Setting params for ep #83 (type 1, 4 urbs), ret=0
[ 3204.521182] usb 1-2: Starting data EP @ffff880035fce000
[ 3204.521204] usb 1-2: Starting sync EP @ffff8800bd616000
second playback to adaptive endpoint: no audio and error on terminal:
$ aplay -Dhw:1,0 ~/24_96.wav
Playing WAVE '/home/plb/24_96.wav' : Signed 24 bit Little Endian in 3bytes,
Rate 96000 Hz, Stereo
aplay: pcm_write:1939: write error: Input/output error
[ 3239.483589] usb 1-2: setting usb interface 1:1
[ 3239.483601] usb 1-2: Re-using EP 3 in iface 1,1 @ffff880035fc8000
[ 3239.484590] usb 1-2: Setting params for ep #3 (type 0, 4 urbs), ret=0
[ 3239.484606] usb 1-2: Setting params for ep #83 (type 1, 4 urbs), ret=0
This last line shows that a sync endpoint is used when it shouldn't.
The sync endpoint is no longer valid and the pointers are corrupted
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
add wm8960 support for fsl-asoc-card
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add OF match table to SSM2518 to allow direct matching without going
through I2C subsystem.
Signed-off-by: Ricard Wanderlof <ricardw@axis.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PCM DAIs need to be loaded and added to ASoC core ealier than the
graph (route). Otherwise, adding routes will fail for missing DAIs.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adjust set DAI format function in fsl_ssi driver
so it doesn't fail and clears RXDIR in AC'97 mode.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instantiate AC'97 CODEC in fsl_ssi driver AC'97 mode.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check whether setting AC'97 ops succeeded and clean them
on removal so the fsl_ssi driver can be reloaded.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
AC'97 bus can support asymmetric playback/capture rates
so enable them in this case in fsl_ssi driver.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
AC'97 DAI driver struct need the same probe method as
I2S one to setup DMA params in fsl_ssi driver.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
IPG clock have to be enabled during AC'97 CODEC register
access in fsl_ssi driver.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even the
call returns an error code. Thus a pairing decrement is needed on the
error handling path to keep the counter balanced.
Signed-off-by: Junjie Mao <junjie.mao@enight.me>
Signed-off-by: Mark Brown <broonie@kernel.org>
The readable registers are in continuous ranges: 0x01 ~ 0x03, 0x05 ~ 0x5f.
Use case range syntax makes the code shorter with better readability when
we have a large number of continuous switch cases.
No functional change with this patch.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The readable registers are in continuous range: 0x01 ~ 0x2e.
Use case range syntax makes the code shorter with better readability when
we have a large number of continuous switch cases.
No functional change with this patch.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The readable registers are in continuous range: 0x01 ~ 0x34.
Use case range syntax makes the code shorter with better readability when
we have a large number of continuous switch cases.
No functional change with this patch.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use case range syntax makes the code shorter with better readability when
we have a large number of continuous switch cases.
Below are the summary of readable/volatile/precious registers.
The readable registers:
0x01 ~ 0x0D, 0x0F ~ 0x1C
The volatile registers:
0x01 ~ 0x05, 0x15 ~ 0x18
The precious registers:
0x15 ~ 0x18
No functional change with this patch.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use managed resource functions devm_clk_put and
devm_snd_soc_register_component to simplify error handling.
To be compatible with the change various gotos are replaced
with direct returns, and unneeded labels are dropped.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ssm4567 has sensing circuitry that can be used to monitor the current
and voltage on the speaker amplifier output has well as the VBAT input.
This data can be output over the I2S interface so it can be processed by a
DSP or similar.
This patch adds the sense capture output stream to the CODEC DAI as well as
DAPM widgets that ensure that the sensing circuitry is powered up when the
capture stream is active.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't set .read_flag_mask for adav803, it's for adav801 only.
Fixes: 0c2d696456 ("ASoC: adav80x: Split SPI and I2C code into different modules")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
USB Audio Class version 2.0 supports three different parameter block sizes for
CUR requests, which are 1 byte (5.2.3.1 Layout 1 Parameter Block), 2 bytes
(5.2.3.2 Layout 2 Parameter Block) and 4 bytes (5.2.3.3 Layout 3 Parameter
Block). Use the correct size according to the specific control as it was
already done for UACv1. The allocated block size for control requests is
increased to support the 4 byte worst case.
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The dev->name of CODEC might not be identical to its codec_dai_name,
so using dev->name to probe the CODEC dai is not a correct approach.
This patch specifies each supporting codec_dai_name instead of using
dev->name any more.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_dapm_input_path and snd_soc_dapm_output_path trace events are
identical except for the direction. Instead of having two events have a
single one that has a field that contains the direction.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
After the recent cleanups and generalizations of the DAPM algorithm the
handling of input and output paths is now fully symmetric. This means by
making some slight changes to the data structure and using arrays with one
entry for each direction, rather than separate fields, it is possible to
create a generic implementation that is capable of handling both input and
output paths.
Unfortunately this generalization significantly increases the code size on
the hot path of is_connected_{input,output}_ep() and
dapm_widget_invalidate_{input,output}_paths(), which has a negative impact
on the overall performance. The inner loops of those functions are quite
small and the generic implementation adds extra pointer arithmetic in a few
places.
Testing on ARM shows that the combined code size of the specialized
functions is about 50% larger than the generalized function in relative
numbers. But in absolute numbers its less than 200 bytes, which is still
quite small. On the other hand the generalized function increases the
execution time of dapm_power_one_widget() by 30%. Given that this function
is one of the most often called functions of the DAPM framework the
trade-off of getting better performance at expense of generating slightly
larger code at seems to be worth it.
To avoid this still keep two versions of these functions around, one for
input and one for output. But have a generic implementation of the
algorithm which gets inlined by those two versions. And then let the
compiler take care of optimizing it and removing he extra instructions.
This still reduces the source code size as well as the makes making changes
to the implementation more straight forward since the same change does no
longer need to be done in two separate places. Also on the slow paths we
can use a generic implementations that handle both input and output paths.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure to unlock the DAPM mutex when dapm_widget_list_create() fails.
This means the function will now generate a trace_snd_soc_dapm_connected
event, even if the creation of the list fails. But that was the behavior
before the patch that introduced the unlock issue, so that should be fine.
Fixes: 1ce43acff0 ("ASoC: dapm: Simplify list creation in dapm_dai_get_connected_widgets()")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Dell laptop causes the white noise by login screen and headphone,
and the fixup function ALC292_FIXUP_DISABLE_AAMIX can eliminate this
noise.
Codec: Realtek ALC3235
Vendor Id: 0x10ec0293
Subsystem Id: 0x102806db
Cc: <stable@vger.kernel.org>
BugLink: https://bugs.launchpad.net/bugs/1484334
Signed-off-by: Woodrow Shen <woodrow.shen@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are too much noise about the typos for fsl's drivers. So I fix
all the typos here in this patch in almost every file I touched.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add 32 bit word length support. There are no code changes required
in the SAI driver since it has already wirten the word width to the
corresponding register.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The power for line out was not turned on when line out is enabled.
So we add "LOUT amp" widget to turn on the power for line out.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
On arm64:
sound/soc/sh/rcar/dma.c: In function 'rsnd_dmaen_init':
sound/soc/sh/rcar/dma.c:180:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(void *)id);
^
include/linux/dmaengine.h:1185:75: note: in definition of macro 'dma_request_channel'
#define dma_request_channel(mask, x, y) __dma_request_channel(&(mask), x, y)
^
Add an intermediate cast to "uintptr_t" to kill the compile warning.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add sysclk auto mode. When it's sysclk auto mode, if the MCLK is
available for clock configure, using MCLK to provide sysclk directly,
otherwise, search a available pll out frequcncy and set pll.
Configure clock in hw_params may cause problems when using bypass style
paths without hw_params in machine driver getting called. So add configure
clock to set_bias_level.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Alienware 15 has CA0132 codec for its onboard sound, but the pin
config and mapping seem quite different from other Creative boards.
This patch corrects them, at least, for providing the right headphone
and mic jack notification, as well as removing the non-existing SPDIF
pins.
Even with this fix, not all stuff works perfectly yet, mainly because
of the badly written ca0132 driver code -- it has too many implicit
assumptions of pin configs and maps. Nevertheless, this is a small
good step forward.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=101981
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The echoaudio locally defines TRUE and FALSE. Not only is this
redundant given that C now has a boolean type it results in lots of
warnings as other headers also define these macros, causing duplicate
definitions. Fix this by removing the local defines and converting all
local users to use the standard C true and false instead, simply
removing the macros is less safe due to implicit inclusion of the other
definitons.
[fixed overlooked replacement of FALSE by tiwai]
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enforce correct device sequencing when configuring a new
audio route when there is an existing active audio route(s).
This patch fixed recording noise issue while playback is active.
We have some registers which require the device to be in full shutdown
or to enter full shutdown before the register settings will take effect.
Currently the driver is not shutting down the device when a new audio
route is created. If a new audio route is made active while there is
already an active audio route, then the required register sequencing is
violated. A hardware shutdown toggle when creating a new audio route
corrects the sequencing error. The device must remain in hardware
shutdown for 40ms to allow the internal hardware core to fully shutdown.
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Acked-by: Anish Kumar <anish.kumar@maximintegrated.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To manage DSP we need to create processing pipeline and on cleanup destroy
them. So we add create and destroy routines for pipelines The pipelines need
to to be executed so we add pipeline run and stop routines
All these send required IPCs to DSP using IPC routines added earlier
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A module needs to be instantiated and then connected with other modules. On
cleanup we need to disconnect the module.
This is achieved by helpers module init, bind and unbind which are added
here
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SRC and converter modules are required to do frequency and channel
conversion in DSP. Both take base module configuration and additional SRC
and converter parameters. The helpers here are added to calculate the values
for these modules
Signed-off-by: Hardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds helper functions to calculate parameters required for base module
format and copier module. A generic module is modelled by base module.
Copier module is responsible for getting/sending data to FE (host DMAs) and
BE (link HDA DMA, SSP, PDM)
This also ads module pin management helpers which help in finding pins to
use or freeing them up
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of defining own acpi header, use the available acpi
header defined in acpi framework.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sampling rate type needs to be u32 instead of u8, nhlt wav format
description expected u32 for rate, passing u8 will fetch NULL
config in skl_get_ep_blob().
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch was generated using fixed coccinelle semantic patch
scripts/coccinelle/api/memdup.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2014320
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch was generated using fixed coccinelle semantic patch
scripts/coccinelle/api/memdup.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2014320
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes a typo in the description for SND_OMAP_SOC_HDMI_AUDIO.
Signed-off-by: Nik Nyby <nikolas@gnu.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
There are a couple of small driver specific fixes here but the
overwhelming bulk of these changes are fixes to the topology ABI that
has been newly introduced in v4.2. Once this makes it into a release we
will have to firm this up but for now getting enhancements in before
they've made it into a release is the most expedient thing.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVxJsBAAoJECTWi3JdVIfQHUIH/2NeQyG7bL3TSIm0qK9RdmaT
UrWyGm6AwhOrg9j9jnZkXag1v4Fsmo4nnslaDbmCKaWJPs7ol94NuWJK7z3He3nr
47yxl2m8OhxsS7aBDACa4gJFQce+JSjKs1ADnKR7QzY9c1/nTAWLO/LE/I5Ca18u
tZg77hviip2ftfLYdNXDZvz3HzuCcRnIouc4izTs16DXwU3aYpqcctFrcqU3nNmp
/+5zPwIoLA7KDwPqdYhSPNRuCnFtjVbI8hTzq+aWFlxFBZYlKmSCTSwpCN2aQDgF
1oCOP4dlv7s9Xavd2TOMJ8g3Fuyb/gjX2DhIEm7QCYxwBxdkpwm0na6gMrRJqsg=
=NEOq
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.2
There are a couple of small driver specific fixes here but the
overwhelming bulk of these changes are fixes to the topology ABI that
has been newly introduced in v4.2. Once this makes it into a release we
will have to firm this up but for now getting enhancements in before
they've made it into a release is the most expedient thing.
Currently the TLV topology structure is targeted at only supporting the
DB scale data. This patch extends support for the other TLV types so they
can be easily added at a later stage.
TLV structure is moved to common topology control header since it's a
common field for controls and can be processed in a general way.
Users must set a proper access flag for a control since it's used to
decide if the TLV field is valid and if a TLV callback is needed.
Removed the following fields from topology TLV struct:
- size/count: type can decide the size.
- numid: not needed to initialize TLV for kcontrol.
- data: replaced by the type specific struct.
Added TLV structure to generic control header and removed TLV structure
from mixer control.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A lot of small fixes here, a few to the core:
- Fix for binding DAPM stream widgets on devices with prefixes assigned
to them
- Minor fixes for the newly added topology interfaces
- Locking and memory leak fixes for DAPM
- Driver specific fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVsnNFAAoJECTWi3JdVIfQH9cH/1ddueDFikvXSCyntuJcHAwJ
a7X5kCVdegMnaMK5fnAbTlJBpDIX/F1UBvsFQQ38eKWeneP44XnkXeh/32fGJzQO
L730dqy0tkgQdWJkQg0yxaP5/k0BfhnXeRc3ATUG3LBgUBrWRYLTIvaM+G+H3Kf5
K88QL7cKmeY0Kt6+cms3nnBj9x5oFgbHIW7Y3K/pza+XPVecZ7N3/5gpV+VQDUXh
Oz3cZOsC5h4+IpxkOrLXY7zgLvrt/HfRTO2QF/3Ntub81anAk190pVAquM+r/CTn
tQ3sPNGLglQ4VRXNP6yBKJOp5CUTBLt5XWlJ+Kg9p2OiiuOPla4wkhuGDS5AM64=
=nJJl
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.2-rc3' into asoc-fix-topology
ASoC: Fixes for v4.2
A lot of small fixes here, a few to the core:
- Fix for binding DAPM stream widgets on devices with prefixes assigned
to them
- Minor fixes for the newly added topology interfaces
- Locking and memory leak fixes for DAPM
- Driver specific fixes
Some widgets may need sorting within, So add this support in topology.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Existing implementation checks all divider values and tracks
'red' proximity value for the frequency.
But as divider array is monotonically increasing the first
divider that gives DMIC rate in 3MHz range is the best one
we should use. No need for 'red' zone tracking.
Additionally make sure that DMIC frequency is higher 1MHz.
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Acked-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Update the aoa-soundbus framework to use dev_pm_ops rather than the
deprecated legacy suspend and resume callbacks.
Since there isn't anything special to do at the bus level the bus driver
does not have to implement any callbacks. The device driver core will
automatically pick up and execute the device's PM ops.
As there is only a single aoa-soundbus driver implementing suspend and
resume, update both the core and driver at the same time to avoid
unnecessary code churn.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch introduces the use of managed resource function
devm_clk_get instead of clk_get and removes corresponding calls
to clk_put in the probe and remove functions.
To be compatible with the change various gotos are replaced with
direct returns, and unneeded labels are dropped.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When .max_register is set and .writeable_reg is not implement, registers
between 0 and .max_register are writeable. This is the same as current
implementation of wm8753_writeable(), so just drop implementation for
.writeable_reg callback.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When .max_register is set and .writeable_reg is not implement, registers
between 0 and .max_register are writeable. This is the same as current
implementation of wm8731_writeable(), so just drop implementation for
.writeable_reg callback.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
For TLVs with only a single entry it is not necessary to use a range
container. Use DECLARE_TLV_DB_LINEAR() directly instead of a combination of
TLV_DB_RANGE_HEAD() and TLV_DB_LINEAR_ITEM().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
For TLVs with only a single entry it is not necessary to use a range
container. Use DECLARE_TLV_DB_SCALE() directly instead of a combination of
TLV_DB_RANGE_HEAD() and TLV_DB_SCALE_ITEM().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
For TLVs with only a single entry it is not necessary to use a range
container. Use DECLARE_TLV_DB_SCALE() directly instead of a combination of
TLV_DB_RANGE_HEAD() and TLV_DB_SCALE_ITEM().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Oder Chiou