When write-verify is enabled (CONFIG_MTD_ONENAND_VERIFY_WRITE),
the data written is read back and compared. The comparison
was being made between dataRAM buffers, but this does not
verify that the data made it to the dataRAM correctly in
the first place. This patch amends write-verify to
compare back to the original buffer. It also now verifies
sub-page writes.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The precise timings are board-specific (or NAND chip specific) and don't
belong here. If they're set already, then use what we find there.
Otherwise, revert to the most conservative default values (and whinge).
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
OneNAND records bad block information in the out-of-band area of either the first or second page of a block. Due to a logic error, only the first page was being checked.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
OneNAND does 2 memory allocations for bad block information.
Only one of them was being freed.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
If OneNAND is operating within specification, all operations should easily be
completed within the 20 millisecond timeout.
This patch faithlessly adds a check for the timeout and returns an error in
that case.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The read-while-load method of reading from OneNAND needs to allow
for the change of bufferRAM address at the boundary between the
two chips in a double density (DDP) device.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
we don't need to return ecc error when 1-bit ecc.
We only return error code when 2-bit ecc error
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch teaches OneNAND to release processor in
read/write/erase cycles and let other processes proceed.
Also, remove buggi touch watchdog call which only hides
the problem instead of solving it.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Return a fault code if the Dataflash driver runs into a "no device present"
error when the MISO line has a pulldown (it currently expects a pullup), so
that rmmod won't oops.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix build issues that show up with the m25p80 SPI flash driver when
building with MTD debug enabled.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Run this:
#!/bin/sh
for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do
echo "De-casting $f..."
perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f
done
And then go through and reinstate those cases where code is casting pointers
to non-pointers.
And then drop a few hunks which conflicted with outstanding work.
Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
All kcalloc() calls of the form "kcalloc(1,...)" are converted to the
equivalent kzalloc() calls, and a few kcalloc() calls with the incorrect
ordering of the first two arguments are fixed.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the ITE8172 based boards was deleted a while ago so this is
dead code.
The Kconfig dependency on MIPS was wrong anyway, MIPS is a processor
architecture and nothing else; guesses on systems architecture are likely
to be wrong ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
I will not commit even trivial and obvious one-line fixes without building.
I will not commit even trivial and obvious one-line fixes without building.
I will not commit even trivial and obvious one-line fixes without building.
I will not commit even trivial and obvious one-line fixes without building.
Only clever people can get away with that.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
ESB2ROM uses PCI interface functions.
With CONFIG_PCI=n:
drivers/mtd/maps/esb2rom.c: In function 'esb2rom_init_one':
drivers/mtd/maps/esb2rom.c:167: warning: implicit declaration of function 'pci_dev_get'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
inlined below is the patch that adds physmap driver for of_device.
It's an MTD part of the two-part support for flash/ROM devices based
on Open Firmware descriptions. The arch part (currently only PowerPC
which is no surprise) was introduced to powerpc folks earlier and
recently the older version of the powerpc part has been included into
the powerpc.git tree
(see http://www.kernel.org/git/?p=linux/kernel/git/paulus/powerpc.git;a=commitdiff;h=28f9ec349ae47c91768b7bc5607db4442c818e11).
drivers/mtd/maps/Kconfig | 9 +
drivers/mtd/maps/Makefile | 1
drivers/mtd/maps/physmap_of.c | 255 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 265 insertions(+)
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Sergey Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
RedBoot supports storing the FIS directory and the RedBoot
configuration area in the same block of flash memory. This is
not the most common RedBoot configuration, but it is used on
commercially available boards supported by the kernel.
A recent patch to mtd/redboot.c (http://lkml.org/lkml/2006/3/20/410)
which corrected the skipping of deleted table entries has exposed the
latent problem of the kernel redboot parser running off the end of the
FIS directory and interpreting the RedBoot configuration information
as table entries.
This patch terminates the table parsing when the first truly empty
entry is found (table entry deletion only clears the first byte of the
name, so two cleared bytes in a row indicates the end of the table),
thereby supporting the combined redboot FIS directory and RedBoot
configuration information flash layout scenario.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for 16-bit NAND bus-width for the AT91 NAND driver.
The 16-bit NAND is found on the Atmel AT91SAM9260-EK and AT91SAM9261-EK
boards.
Orignal Patch from Patrice Vilchez
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Number of address bytes for 64-128 MiB NANDs is 4, not 5.
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
SLAB_KERNEL is an alias of GFP_KERNEL.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Select MTD_NAND_ECC_SMC (ECC byte order according to the Smart Media
Specification) if MTD_NAND_NDFC is used.
Using the wrong byte order causes fatal, unnoticed data damage.
For further information see:
http://lists.infradead.org/pipermail/linux-mtd/2006-November/016920.html
Signed-off-by: Timo Lindhorst <lindhors@linux.vnet.ibm.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Can't analyze FIS directory in CYGSEM_REDBOOT_FLASH_COMBINED_FIS_AND_CONFIG
really.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch fixes the
"jffs2_flash_writev(): Non-contiguous write to 00825300 with mtd_dataflash" bug.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
The newly-added cafe_ecc.c had a lot of it because of the way the lookup
table was auto-generated; clean up the other files too while we're at it.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Changes persistant -> persistent. www.dictionary.com does not know
persistant (with an A), but should it be one of those things you can
spell in more than one correct way, let me know.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Fix various Kconfig typos.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
While we're fixing up the newly-added symbol, change the neighbouring ones
too, for consistency and also to reflect the author's interpretation of
the GPL -- which is that _no_ non-GPL modules are permitted. The author
always intended his code to be released under the GPL, and believes that
any new interpretation of 'EXPORT_SYMBOL' as being any different from
'EXPORT_SYMBOL_GPL' is entirely invalid; the GPL requires that _all_
exports have the semantics of the new 'EXPORT_SYMBOL_GPL', which means the
extra four characters are entirely redundant.
But since those four extra characters trigger the check for illegal
modules in a way that just EXPORT_SYMBOL does not, it's useful to change
anyway. This action in no way indicates an admission that there is any
legal distinction between the two states, and in particular does not
indicate that the author believes that non-GPL modules may use symbols
exported with EXPORT_SYMBOL alone.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
get_mtd_device() returns NULL in case of any failure. Teach it to return an
error code instead. Fix all users as well.
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
This patch adds get_device() and put_device() methods to the MTD description
structure (struct mtd_info). These methods are called by MTD whenever the MTD
device is get or put. They are needed when the underlying driver is something
smarter then just flash chip driver, for example UBI.
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
This patch adds one more function to the MTD interface to make it possible to
open MTD devices by their names, not only numbers. This is very handy in many
situations. Also, MTD device number depend on load order and may vary, while
names are fixed.
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
Add a MTD_BLKDEVS Kconfig option to cleanup the makefile a bit
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
This patch has fixed name of map probe for cstm_mips_ixx.c
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
When we sleep and wait for a suspended operation to be resumed, go
back and check until it's ready -- don't just continue after the first
time we're woken. This can cause file system corruption.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix up the config option in the #ifdef statements in nand_ecc.c
Signed-off-by: Timo Lindhorst <lindhors@linux.vnet.ibm.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix printk format warning:
drivers/mtd/maps/physmap.c:93: warning: long long unsigned int format, long unsigned int arg (arg 2)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
As was discussed between Ricard Wanderlöf, David Woodhouse, Artem
Bityutskiy and me, the current API for reading/writing OOB is confusing.
The thing that introduces confusion is the need to specify ops.len
together with ops.ooblen for reads/writes that concern only OOB not data
area. So, ops.len is overloaded: when ops.datbuf != NULL it serves to
specify the length of the data read, and when ops.datbuf == NULL, it
serves to specify the full OOB read length.
The patch inlined below is the slightly updated version of the previous
patch serving the same purpose, but with the new Artem's comments taken
into account.
Artem, BTW, thanks a lot for your valuable input!
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Currently, mtd_blkdevs enforces a block size of 512, even if the drivers
can seemingly request a different size. This patch fixes mtd_blkdevs so
block sizes other than 512 work correctly.
Signed-off-by: Richard Purdie <rpurdie@openedhand.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for accessing BIOS flash chips connected to the NVIDIA ck804 southbridge.
Signed-off-by: Ryan Jackson <rjackson@lnxi.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The writel() call accidentally clears all bits in the NDFC_CCR
register (endianess problem). Now __raw_writel() is used instead.
Tested on Bamboo with NAND on chip select 0 and chip select 1.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch makes the needlessly global mtdpart_setup() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch converts drivers/mtd/nand/rtc_from4.c to use the new
lib/bitrev.c
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
We can use the two methods to wait.
1. polling: read interrupt status register
2. interrupt: use kernel ineterrupt mechanism
To use interrupt method, you first connect onenand interrupt pin to your
platform and configure interrupt properly
Signed-off-by: Kyungmin Park <kyungmin.park at samsung.com>
We were resetting cafe->ctl2 to zero after an erase (and also during a
write, but it was correctly reset after that). This meant that ECC reads
after an erase were failing. Doh.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Also use cafe_readl() and cafe_writel() abstraction to make code
slightly cleaner -- especially if we want to use it in PIO mode.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add description of 'raw' in comments for
drivers/mtd/nand/nand_base.c::nand_write_page_syndrome() so 'make xmldocs'
will not spew a warning at us.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Being a value which isn't in the table is a case we explicitly check for
in the caller. Don't BUG_ON() because it does actually happen in
practice.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When a flash-based BBT is not used, nand_default_mark_blockbad() is supposed
to mark the block bad in the oob. However, it sets the wrong length variable
so that no bad block marker is in fact written. This patch attempts to
rectify that.
(As note, it seems to be that logically, it shouldn't be necessary to set
both length variables, as one appears to be for the main buffer, and
one for the oob buffer, but this is how it is done in several places,
including the code for the mtd character device MEMWRITEOOB and MEMREADOOB
ioctls. I'm not sure if this is a temporary solution during some rework of
the mtd infrastructure, or whether there is a deeper thought here.)
Signed-off-by: Ricard Wanderlöf <ricardw@axis.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Ditch the separate oobrbuf and oobwbuf fields from the chip buffers,
and use only a single buffer immediately after the data. This accommodates
NAND controllers such as the OLPC CAFÉ chip, which can't do scatter/gather
DMA so needs the OOB buffer to be contiguous with the data, for both read
and write.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
As flash cannot do 0->1 bit transitions when programming, do not do this in
the simulator too. This makes nandsim able to accept subpage writes.
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
During some testing with several samsung s3c24xx based
devices it was discovered that often the
cfi_cmdset_0001.c would not leave the chip in
read-array mode on suspend. this is an issue if the
same flash chip is used for the bootloader that needs
to be read on resume.
Signed-off-by: David Anders <danders@amltd.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Removes line break after return type in function definitions, to be
consistent with the Linux coding style.
Signed-off-by: Vijay Kumar <vijaykumar@bravegnu.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
For page wise allocation, an array of flash page pointers is allocated
during initialization. The flash pages are themselves allocated when a
write occurs to the page. The flash pages are deallocated when they
are erased.
Signed-off-by: Vijay Kumar <vijaykumar@bravegnu.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch removes code that does chip mapping. The chip mapping code
is no longer used.
Signed-off-by: Vijay Kumar <vijaykumar@bravegnu.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch has removed ITE 8172G and Globespan IVR MTD support.
These boards support have already been removed.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Acked-by: Ralf Bächle <ralf@linux-mips.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
1. The ECCGETLAYOUT ioctl copy_to_user() call has a superfluous '&'
causing the resulting information to be garbage rather than the intended
mtd->ecclayout.
2. The MEMGETOOBSEL misses copying mtd->ecclayout->eccbytes so the
resulting field of the returned structure contains garbage.
Signed-off-by: Ricard Wanderlöf <ricardw@axis.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This version only differs from version posted by Savin Zlobec (20 Jun
2006) in that the AT91RM9200-specific chip-select / bus setup code has
been moved from the at91_nand.c driver into the processor-specific file.
From: Savin Zlobec <savin@epico.si>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fairly self explanatory. Keep a reference initially, drop it when we free up
the driver resources.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add MTD map driver for BIOS flash chips connected to the Intel ESB2
southbridge.
[akpm@osdl.org: coding-style fixes, build fix]
Signed-off-by: Ryan Jackson <rjackson@lnxi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add chip driver and JEDEC probe support for the SST 49LF040B flash chip.
Signed-off-by: Ryan Jackson <rjackson@lnxi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The 2 bits controlling the window size are often set to allow reading the
BIOS, but too small to allow writing, since the lock registers are 4MiB
lower in the address space than the data. This is intended to prevent
flashing the bios, perhaps accidentally.
The bits are 6 and 7. If both bits are set, it is a 5MiB window. If only
the 7 Bit is set, it is a 4MiB window. Otherwise, it is a 64KiB window.
This parameter allows the driver to override the BIOS settings.
Signed-off-by: Ryan Jackson <rjackson@lnxi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch fixes the following compile error with
CONFIG_SSFDC=m, CONFIG_BLOCK=n:
<-- snip -->
...
CC [M] drivers/mtd/mtd_blkdevs.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/mtd/mtd_blkdevs.c:40: warning: ‘struct request’ declared inside parameter list
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/mtd/mtd_blkdevs.c:40: warning: its scope is only this definition or declaration, which is probably not what you want
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/mtd/mtd_blkdevs.c: In function ‘do_blktrans_request’:
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/mtd/mtd_blkdevs.c:45: error: dereferencing pointer to incomplete type
...
make[3]: *** [drivers/mtd/mtd_blkdevs.o] Error 1
<-- snip -->
Bug report by Jesper Juhl.
This patch also removes a pointless "default n" from the SSFDC option.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Updated version of patch, in response to comments from Francois Romieu
<romieu@fr.zoreil.com>
Remove gratuitous casts from iounmap and initialisation of variables.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Building 2.6.18-mm2 issues the following warning if CONFIG_NFTL_RW is not set:
CC [M] drivers/mtd/nftlcore.o
drivers/mtd/nftlcore.c:183: warning: 'nftl_write' defined but not used
The following patch only compiles nftl_write if CONFIG_NFTL_RW is set.
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
gcc spits out this warning:
drivers/mtd/mtd_blkdevs.c: In function ‘do_blktrans_request’:
drivers/mtd/mtd_blkdevs.c:72: warning: format ‘%ld’ expects type ‘long int’, but argument 2 has type ‘unsigned int’
This could be fixed any number of ways, including use of BUG().
rq_data_dir() only returns 0 or 1, so this entire case is superfluous.
I did the most simple fix.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Make it possible to disable the block layer. Not all embedded devices require
it, some can make do with just JFFS2, NFS, ramfs, etc - none of which require
the block layer to be present.
This patch does the following:
(*) Introduces CONFIG_BLOCK to disable the block layer, buffering and blockdev
support.
(*) Adds dependencies on CONFIG_BLOCK to any configuration item that controls
an item that uses the block layer. This includes:
(*) Block I/O tracing.
(*) Disk partition code.
(*) All filesystems that are block based, eg: Ext3, ReiserFS, ISOFS.
(*) The SCSI layer. As far as I can tell, even SCSI chardevs use the
block layer to do scheduling. Some drivers that use SCSI facilities -
such as USB storage - end up disabled indirectly from this.
(*) Various block-based device drivers, such as IDE and the old CDROM
drivers.
(*) MTD blockdev handling and FTL.
(*) JFFS - which uses set_bdev_super(), something it could avoid doing by
taking a leaf out of JFFS2's book.
(*) Makes most of the contents of linux/blkdev.h, linux/buffer_head.h and
linux/elevator.h contingent on CONFIG_BLOCK being set. sector_div() is,
however, still used in places, and so is still available.
(*) Also made contingent are the contents of linux/mpage.h, linux/genhd.h and
parts of linux/fs.h.
(*) Makes a number of files in fs/ contingent on CONFIG_BLOCK.
(*) Makes mm/bounce.c (bounce buffering) contingent on CONFIG_BLOCK.
(*) set_page_dirty() doesn't call __set_page_dirty_buffers() if CONFIG_BLOCK
is not enabled.
(*) fs/no-block.c is created to hold out-of-line stubs and things that are
required when CONFIG_BLOCK is not set:
(*) Default blockdev file operations (to give error ENODEV on opening).
(*) Makes some /proc changes:
(*) /proc/devices does not list any blockdevs.
(*) /proc/diskstats and /proc/partitions are contingent on CONFIG_BLOCK.
(*) Makes some compat ioctl handling contingent on CONFIG_BLOCK.
(*) If CONFIG_BLOCK is not defined, makes sys_quotactl() return -ENODEV if
given command other than Q_SYNC or if a special device is specified.
(*) In init/do_mounts.c, no reference is made to the blockdev routines if
CONFIG_BLOCK is not defined. This does not prohibit NFS roots or JFFS2.
(*) The bdflush, ioprio_set and ioprio_get syscalls can now be absent (return
error ENOSYS by way of cond_syscall if so).
(*) The seclvl_bd_claim() and seclvl_bd_release() security calls do nothing if
CONFIG_BLOCK is not set, since they can't then happen.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Right now ->flags is a bit of a mess: some are request types, and
others are just modifiers. Clean this up by splitting it into
->cmd_type and ->cmd_flags. This allows introduction of generic
Linux block message types, useful for sending generic Linux commands
to block devices.
Signed-off-by: Jens Axboe <axboe@suse.de>
OneNAND lock scheme depends on density and process of chip.
Some OneNAND chips support all block unlock
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Now the bootloader configures the OneNAND sync. burst mode.
So we don't access Sync. burst mode related registers in kernel.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
- allow high-level nand_write_page() function to be overridden
- likewise low-level write_page_raw() and read_page_raw() functions
- Clean up the abuse of chip->ecc.{write,read}_page() with MTD_OOB_RAW
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Don't include <linux/config.h>.
Don't say 'MB' where you mean 'MiB'.
Don't allocate 512 bytes on the stack.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This reverts commit 668040fcd1.
The 'flags' field of the struct request is 'unsigned long'. Quite
how Randy came to see 'long int format, different type arg' I don't
know, but it doesn't seem to be the case any more.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use pci_resource_start for getting start of regions and pci_iomap to not
doing this directly by using dev->resource... (Thanks to Rolf Eike Beer)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Spaces were used for indent, there was more than 80 columns per line. Get
rid of that stuff.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The iq80310 mtd map driver depends on ARCH_IQ80310, which isn't
defined anywhere in the tree (as we don't have 80310 support), and
furthermore, everything the driver does can be done with physmap
instead.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Due to this typo, a wrong ECC layout table is chosen.
Signed-off-by: Frank Haverkamp <haver@vnet.ibm.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Implement PM handling for physmap. Idea from Steven Scholz, patch
by David Anders.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Tested (compilation only) with:
- allmodconfig
- Modifying drivers/mtd/maps/Kconfig and drivers/mtd/nand/Kconfig to
make sure that the changed file is compiling without warning
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix printk format warning(s):
drivers/mtd/mtd_blkdevs.c:72: warning: long int format, different type arg (arg 2)
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
If the amount of flash is not divisible by 2 then the mask in
parse_mtd_partitions would fail to work as designed. Passing in the base
address corrects this problem.
Signed-off-by: Brian Walsh <brian@walsh.ws>
Cc: Deepak Sanexa <dsanexa@mvista.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Introduce the MTD_STUPID_LOCK flag which indicates that the flash chip is
always locked after power-up, so all sectors need to be unlocked before it
is usable.
If this flag is set, and the chip provides an unlock() operation,
mtd_add_device will unlock the whole MTD device if it's writeable. This
means that non-writeable partitions will stay locked.
Set MTD_STUPID_LOCK in fixup_use_atmel_lock() so that these chips will work
as expected.
Signed-off-by: Håvard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The memset() in fixup_convert_atmel_pri is supposed to zero out
everything except the first 5 bytes in *extp, but it ends up zeroing
out something way outside the struct instead. Fix this potentially
dangerous code by casting the pointer to char * before doing
arithmetic.
Signed-off-by: Håvard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The flash_info structure has a bunch of missing fields which causes problems
when actually tryin to use some ST parts as it gets detected incorrectly.
Signed-off-by: Aubrey L1 <aubreylee@gmail.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
The recent hwctrl core conversion for MTD NAND devices broke the Amstrad
Delta driver. This fixes it up and uses the existing control line defines
rather than unclear magic numbers.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Read the return value before we release the nand device otherwise the
value can become corrupted by another user of chip->ops, ultimately
resulting in filesystem corruption.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The AT49BV6416 is locked by default, so we really need to provide
at least the unlock() operation for write and erase to work. This
patch implements both ->lock() and ->unlock() and provides a fixup
to install them when an AT49BV6416 chip is detected.
These functions are probably valid on more Atmel chips, but I believe
it's mostly obsolete ones. The AT49BV6416 is in fact obsolete, but
it's used on all current AT32STK1000 development boards.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Atmel flash chips don't have PRI information in the same format as
AMD flash chips. This patch installs a fixup for all Atmel chips that
converts the relevant PRI fields into AMD format.
Only the fields that are actually used by the command set is actually
converted. The rest are initialized to zero (which should be safe)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
map/physmap.c tries to probe "cfi_probe", "jedec_probe" and "map_rom", but
map/Kconfig says it depends on MTD_CFI only.
This patch adds MTD_JEDECPROBE and MTD_ROM to the dependency condition.
Signed-off-by: Takashi YOSHII <takasi-y@ops.dti.ne.jp>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Fix of performance and stability issues on Intel NOR chips. It fixes:
1. Very low write performance on Sibley (perf tests demonstrated write
performance less than 100Kb/sec when it should be over 400Kb/sec).
2. Low erase performance. (perf tests on Sibleuy demonstrated erase
performance 246Kb/sec when it should be over 300Kb/sec).
3. Error on JFFS2 tests with CPU loading application when MTD returns
"block erase error: (status timeout)" To fix the issue it does the
following:
1. Removes the timeout tuning from inval_cache_and_wait_for_operation.
2. Waiting conditions in inval_cache_and_wait_for_operation now is
based on timer resolution
If timeout is lower than timer resolution then we do in cycle
"Checking the status"
udelay(1);
cond_resched();
If timeout is greater than timer resolution (probably erase
operation) We do the following
sleep for half of operation timeout and do in cycle the following
"Checking the status"
sleep for timer resolution
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Trying to pass kernel command line arguments to block2mtd at boot-time does
not work currently. block2mtd_setup() is called so early that kmalloc()
fails nevermind being able to do open_bdev_excl() (which requires rootfs to
be mounted. This patch only saves the option string at the early boot stage,
and parses them later when block2mtd_init() is called. If open_bdev_excl()
fails, open_by_devnum(name_to_dev_t()) is tried instead, which makes it
possible to initialize the driver before rootfs has been mounted. Also gets
rid of the superfluous parse_name() that only checks if name is longer than
80 chars and copies it to a string that is not kfreed.
With this patch, I can boot statically compiled block2mtd, and mount jffs2
as rootfs (without modules or initrd), with lilo config like this:
root=/dev/mtdblock0
append="rootfstype=jffs2 block2mtd.block2mtd=/dev/hdc2,65536"
(Note that rootfstype=jffs2 is required, since the kernel only tries
filesystems without "nodev" attribute by default, and jffs is "nodev").
Compared to first version of this patch, this one does not copy the
parameters to the global buffer if init has already been called, and the
global array is marked as __initdata.
Compared to the second version of this patch, module build is fixed.
Compared to the third version of this patch, statically compiled block2mtd
driver with no boot-time parameter no longer gives spurious error 'cannot
open device ""'
Signed-off-by: Ville Herva <vherva@vianova.fi>
Acked-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
PMC551 depends on PCI in Kconfig so there is no need to #error in code if PCI
is not set.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The CNE bits are inverted on the device and writeb function is missing a
NOT operation.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
In the case of data-pad-ecc-pad-data... layout the oob start position
has to be sizeof(data) in nand_write_oob_syndrom().
In nand_fill_oob() we need to copy to buf + buffer offset instead of
buf + write offset.
From: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
[PATCH] i386: export memory more than 4G through /proc/iomem
[PATCH] 64bit Resource: finally enable 64bit resource sizes
[PATCH] 64bit Resource: convert a few remaining drivers to use resource_size_t where needed
[PATCH] 64bit resource: change pnp core to use resource_size_t
[PATCH] 64bit resource: change pci core and arch code to use resource_size_t
[PATCH] 64bit resource: change resource core to use resource_size_t
[PATCH] 64bit resource: introduce resource_size_t for the start and end of struct resource
[PATCH] 64bit resource: fix up printks for resources in misc drivers
[PATCH] 64bit resource: fix up printks for resources in arch and core code
[PATCH] 64bit resource: fix up printks for resources in pcmcia drivers
[PATCH] 64bit resource: fix up printks for resources in video drivers
[PATCH] 64bit resource: fix up printks for resources in ide drivers
[PATCH] 64bit resource: fix up printks for resources in mtd drivers
[PATCH] 64bit resource: fix up printks for resources in pci core and hotplug drivers
[PATCH] 64bit resource: fix up printks for resources in networks drivers
[PATCH] 64bit resource: fix up printks for resources in sound drivers
[PATCH] 64bit resource: C99 changes for struct resource declarations
Fixed up trivial conflict in drivers/ide/pci/cmd64x.c (the printk that
was changed by the 64-bit resources had been deleted in the meantime ;)
Fix all kernel-doc warnings in MTD headers and source files:
- add some missing struct fields;
- correct some function parameter names;
- use kernel-doc format for function doc. headers;
- nand_ecc.c contains only exported interfaces, no internal ones;
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The NAND rework resulted in non ECC based reads. Fix it up and
do a bit of cleanup while at it.
Pointed out by Adrian Bunk.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The other way round works not really well with boards which have a
static NAND chipselect.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Allow lseek(mtdchar_fd, 0, SEEK_END) to succeed, which currently fails
with EINVAL.
lseek(fd, 0, SEEK_END) should result into the same fileposition as
lseek(fd, 0, SEEK_SET) + read(fd, buf, length(fd))
Furthermore, lseek(fd, 0, SEEK_CUR) should return the current file position,
which in case of an encountered EOF should not result in EINVAL
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
I was unable to compile ts7250.c after your refactor commit,
it's a typo probably.
-- ynezz
From: Petr Stetiar <ynezz@true.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a simple off-by-one error in the mtd physmap driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for both the S3C2412 and S3C2412 Samsung SoCs to
the increasingly mis-named s3c2410.c driver.
This currently only supports SLC ECCs, and a chip on nFCE0.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (40 commits)
kbuild: trivial fixes in Makefile
kbuild: adding symbols in Kconfig and defconfig to TAGS
kbuild: replace abort() with exit(1)
kbuild: support for %.symtypes files
kbuild: fix silentoldconfig recursion
kbuild: add option for stripping modules while installing them
kbuild: kill some false positives from modpost
kbuild: export-symbol usage report generator
kbuild: fix make -rR breakage
kbuild: append -dirty for updated but uncommited changes
kbuild: append git revision for all untagged commits
kbuild: fix module.symvers parsing in modpost
kbuild: ignore make's built-in rules & variables
kbuild: bugfix with initramfs
kbuild: modpost build fix
kbuild: check license compatibility when building modules
kbuild: export-type enhancement to modpost.c
kbuild: add dependency on kernel.release to the package targets
kbuild: `make kernelrelease' speedup
kconfig: KCONFIG_OVERWRITECONFIG
...
The rework of the command handling in the nand driver
led to wrong address setting in the command control
function. Use the correct address again.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Convert the use of printk() to the correct dev_info/dev_err
functions
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The oob fixups broke a return value and missed one patch from
the Mailing List.
Signed-off-by: Savin Zlobec <savin@epico.si>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Following problems are addressed:
- wrong status caused early break out of nand_wait()
- removed the bogus status check in nand_wait() which
is a relict of the abandoned support for interrupted
erase.
- status check moved to the correct place in read_oob
- oob support for syndrom based ecc with strange layouts
- use given offset in the AUTOOOB based oob operations
Partially based on a patch from Vitaly Vool <vwool@ru.mvista.com>
Thanks to Savin Zlobec <savin@epico.si> for tracking down the
status problem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In nand_read_page_syndrome/nand_write_page_syndrome the calculation of
the remaining oob length which is not used by the prepad/ecc/postpad
areas is wrong.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix unused variables and commenting since tglx's
new NAND updates
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Let's not attempt the abolition of mtd->type until/unless it's properly
thought through. And certainly, let's not do it by halves.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This removes all the leading whitespace kconfig now warns about.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Fallout from the incoming 64-bit-resource stuff:
drivers/mtd/maps/physmap.c: In function 'physmap_flash_probe':
drivers/mtd/maps/physmap.c:94: warning: format '%.8lx' expects type 'long
unsigned int', but argument 2 has type 'resource_size_t'
drivers/mtd/maps/physmap.c:94: warning: format '%.8lx' expects type 'long
unsigned int', but argument 3 has type 'resource_size_t'
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
mtdchar.c direcly copied part of struct mtd_info to userspace, thereby
implicitly making it part of the ABI. With this patch, struct
mtd_info is independent of the ABI and can have its fields removed,
reordered, etc.
Signed-off-by: Joern Engel <joern@wh.fh-wedel.de>
Ram devices get the extra capability of MTD_NO_ERASE - not requiring
an explicit erase before writing to it. Currently only mtdblock uses
this capability. Rest of the patch is a simple text replacement.
Signed-off-by: Joern Engel <joern@wh.fh-wedel.de>
No mtd user should ever check for the device type. Instead, device features
should be checked by the flags - if at all.
As a first step towards type removal, change MTD_ROM into MTD_GENERIC_TYPE.
Signed-off-by: Joern Engel <joern@wh.fh-wedel.de>
drivers/mtd/nand/nand_base.c: In function 'nand_transfer_oob':
drivers/mtd/nand/nand_base.c:909: warning: comparison of distinct pointer types lacks a cast
drivers/mtd/nand/nand_base.c: In function 'nand_do_read_oob':
drivers/mtd/nand/nand_base.c:1097: error: 'len' undeclared (first use in this function)
drivers/mtd/nand/nand_base.c:1097: error: (Each undeclared identifier is reported only once
drivers/mtd/nand/nand_base.c:1097: error: for each function it appears in.)
drivers/mtd/nand/nand_base.c: In function 'nand_fill_oob':
drivers/mtd/nand/nand_base.c:1411: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The raw read/write access to NAND (without ECC) has been changed in the
NAND rework. Expose the new way - setting the file mode via ioctl - to
userspace. Also allow to read out the ecc statistics information so userspace
tools can see that bitflips happened and whether errors where correctable
or not. Also expose the number of bad blocks for the partition, so nandwrite
can check if the data fits into the parition before writing to it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Return -EUCLEAN on read when a bitflip was detected and corrected, so the
clients can react and eventually copy the affected block to a spare one.
Make all in kernel users aware of the change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Hopefully the last iteration on this!
The handling of out of band data on NAND was accompanied by tons of fruitless
discussions and halfarsed patches to make it work for a particular
problem. Sufficiently annoyed by I all those "I know it better" mails and the
resonable amount of discarded "it solves my problem" patches, I finally decided
to go for the big rework. After removing the _ecc variants of mtd read/write
functions the solution to satisfy the various requirements was to refactor the
read/write _oob functions in mtd.
The major change is that read/write_oob now takes a pointer to an operation
descriptor structure "struct mtd_oob_ops".instead of having a function with at
least seven arguments.
read/write_oob which should probably renamed to a more descriptive name, can do
the following tasks:
- read/write out of band data
- read/write data content and out of band data
- read/write raw data content and out of band data (ecc disabled)
struct mtd_oob_ops has a mode field, which determines the oob handling mode.
Aside of the MTD_OOB_RAW mode, which is intended to be especially for
diagnostic purposes and some internal functions e.g. bad block table creation,
the other two modes are for mtd clients:
MTD_OOB_PLACE puts/gets the given oob data exactly to/from the place which is
described by the ooboffs and ooblen fields of the mtd_oob_ops strcuture. It's
up to the caller to make sure that the byte positions are not used by the ECC
placement algorithms.
MTD_OOB_AUTO puts/gets the given oob data automaticaly to/from the places in
the out of band area which are described by the oobfree tuples in the ecclayout
data structre which is associated to the devicee.
The decision whether data plus oob or oob only handling is done depends on the
setting of the datbuf member of the data structure. When datbuf == NULL then
the internal read/write_oob functions are selected, otherwise the read/write
data routines are invoked.
Tested on a few platforms with all variants. Please be aware of possible
regressions for your particular device / application scenario
Disclaimer: Any whining will be ignored from those who just contributed "hot
air blurb" and never sat down to tackle the underlying problem of the mess in
the NAND driver grown over time and the big chunk of work to fix up the
existing users. The problem was not the holiness of the existing MTD
interfaces. The problems was the lack of time to go for the big overhaul. It's
easy to add more mess to the existing one, but it takes alot of effort to go
for a real solution.
Improvements and bugfixes are welcome!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Most of those macros are unused and the used ones just obfuscate
the code. Remove them and fixup all users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The nand_oobinfo structure is not fitting the newer error correction
demands anymore. Replace it by struct nand_ecclayout and fixup the users
all over the place. Keep the nand_oobinfo based ioctl for user space
compability reasons.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The info structure for out of band data was copied into
the mtd structure. Make it a pointer and remove the ability
to set it from userspace. The position of ecc bytes is
defined by the hardware and should not be changed by software.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The platform structure was lacking an oobinfo field.
The NDFC driver had some remains from another tree.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We have a type pointer. Make use of it instead of the error prone nand_ids[i]
reference.
The NAND driver used to set default name settings from the chip ID
string for the device. The feature got lost during the rework. Add it back.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
nCE setting can be done when the first command is issued to the device.
We keep the deselect functionality as it makes sense to deassert nCE
when the device becomes idle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Modularize the write function and reorganaize the internal buffer
management. Remove obsolete chip options and fixup all affected
users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
PCI is faked on these devices by SMM traps. Don't depend on that --
check for the chipset directly instead.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Removing readv from struct mtd_info broke block2mtd. Remove the
reference and the useless default implementation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Al Viro