In order to make batman-adv fully vlan aware later, the
semantic used for variables storing the VLAN ID values has
to be changed in order to be adapted to the new one which
will be used batman-adv wide.
In particular, the VID has to be an "_unsigned_ short int"
and its 4 MSB will be used as a flag bitfield, while the
remaining 12 bits are used to store the real VID value
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
While it makes sense to send each broadcast thrice on 802.11 (WLAN) interfaces
as broadcasts are often unreliable on these, there is no reason to do so on
other interface types.
The increased the overhead can be harmful on low-bandwidth links like VPN
connections over slow internet lines, therefore it is better to reduce the
number of broadcast packets sent on non-wireless links to one.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
When receiving a network coded packet, the decoding buffer is searched
for a packet to use for decoding. The source, destination, and crc32 from
the coded packet is used to identify the wanted packet. The decoded
packet is passed to the usual unicast receiver function, as had it never
been network coded.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
To be able to decode a network coded packet, a node must already know
one of the two coded packets. This is done by buffering skbs before
transmission and buffering packets sniffed with promiscuous mode from
other hosts.
Packets are kept in a buffer similar to the one with forward-skbs: A
hash table, where each entry, which corresponds to a src-dst pair, has a
linked list packets.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Before adding forward-skbs to the coding buffer, the buffer is searched
for a potential coding opportunity. If one is found, the two packets are
network coded and transmitted right away. If not, the forward-skb is
added to the buffer.
Network coded packets are transmitted with information about the two
receivers and the two coded packets. The first receiver is given by the
MAC header, while the second is given in the payload/bat-header. The
second receiver uses promiscuous mode to receive the packet and check
the second destination.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Two be able to network code two packets, one packet must be buffered
until the next is available. This is done in a "coding buffer", which is
essentially a hash table with lists of packets. Each entry in the hash
table corresponds to a specific src-dst pair, which has a linked list of
packets that are buffered.
This patch adds skbs to the buffer just before forwarding them. The
buffer is traversed every 10 ms, where timed skbs are removed from the
buffer and transmitted. To allow experiments with the network coding
scheme, the timeout is tunable through a file in debugfs.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
To use network coding efficiently, a relay must know when neighbor nodes
are likely to have enough information to be able to decode a network
coded packet. This is detected by using OGMs from batman-adv to discover
when one neighbor is in range of another neighbor. The relay check the
TLL to detect when an OGM is forwarded from one neighbor by another
neighbor, and thereby knows that the two neighbors are in range and thus
overhear packets sent by each other.
This information is saved in the orig_node struct to be used when
searching for coding opportunities. Two lists are added to the
orig_node struct: One for neighbors that can hear the orig_node
(outgoing nc_nodes) and one for neighbors that the orig_node can hear
(incoming nc_nodes).
Information about nc_nodes is kept for 10 seconds and is available
through debugfs in batman_adv/nc_nodes to use when debugging network
coding.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Network coding exploits the 802.11 shared medium to allow multiple
packets to be sent in a single transmission. In brief, a relay can XOR
two packets, and send the coded packet to two destinations. The
receivers can decode one of the original packets by XOR'ing the coded
packet with the other original packet. This will lead to increased
throughput in topologies where two packets cross one relay.
In a simple topology with three nodes, it takes four transmissions
without network coding to get one packet from Node A to Node B and one
from Node B to Node A:
1. Node A ---- p1 ---> Node R Node B
2. Node A Node R <--- p2 ---- Node B
3. Node A <--- p2 ---- Node R Node B
4. Node A Node R ---- p1 ---> Node B
With network coding, the relay only needs one transmission, which saves
us one slot of valuable airtime:
1. Node A ---- p1 ---> Node R Node B
2. Node A Node R <--- p2 ---- Node B
3. Node A <- p1 x p2 - Node R - p1 x p2 -> Node B
The same principle holds for a topology including five nodes. Here the
packets from Node A and Node B are overheard by Node C and Node D,
respectively. This allows Node R to send a network coded packet to save
one transmission:
Node A Node B
| \ / |
| p1 p2 |
| \ / |
p1 > Node R < p2
| |
| / \ |
| p1 x p2 p1 x p2 |
v / \ v
/ \
Node C < > Node D
More information is available on the open-mesh.org wiki[1].
This patch adds the initial code to support network coding in
batman-adv. It sets up a worker thread to do house keeping and adds a
sysfs file to enable/disable network coding. The feature is disabled by
default, as it requires a wifi-driver with working promiscuous mode, and
also because it adds a small delay at each hop.
[1] http://www.open-mesh.org/projects/batman-adv/wiki/Catwoman
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
When processing the unregister notify for a hard interface, removing
the sysfs files may lead to a circular deadlock (rtnl mutex <->
s_active).
To overcome this problem, postpone the sysfs removal in a worker.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Thanks to Sven Eckelmann and Simon Wunderlich for their support.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
When the Bridge Loop Avoidance component is not compiled-in, its boolean switch
should be not compiled as well. This patch surrounds the switch with a proper
ifdef.
This behaviour was introduced by 9fd6b0615b5499b270d39a92b8790e206cf75833
("batman-adv: add bridge loop avoidance compile option")
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
If the skb is fragmented, the checksum must be computed on the
individual fragments, just using skb->data may fail on fragmented
data. Instead of doing linearizing the packet, use the new
batadv_crc32 to do that more efficiently- it should not hurt
replacing the old crc16 by the new crc32.
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
tt_poss_change is a node-wide flag which tells whether the node is in a roaming
state (a client recently moved to/away from it) in order to let it apply special
re-routing rules. However this flag does not give a clear idea of the current
state because it is not possible to understand *which client* is actually
involved in the roaming. For this reason a better approach has been chosen:
instead of using a node-wide variable, the roaming state is now given by a
per-tt_entry ROAM flag which, in case of packet coming through the node, tells
the node whether the real destination is in roaming state or not.
With this flag change, batadv_check_unicast_ttvn() has also been rearranged in
order to better fit the new re-routing logic and to be much more readable.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
For some reasons (bridge forward delay, network device setup order, etc)
the initial bridge loop avoidance announcement packets may be lost. This
may lead to problems in finding other backbone gws, and therfore create
loops in the startup time.
Fix this by extending the waiting periods to 3 (define can be changed)
before allowing broadcast traffic.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
This patch adds a runtime switch that enables the user to turn the DAT feature
on or off at runtime
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
This patch makes it possible to decide whether to include DAT within the
batman-adv binary or not.
It is extremely useful when the user wants to reduce the size of the resulting
module by cutting off any not needed feature.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Since batman-adv cannot inter-operate with the host ARP table, this patch
introduces a batman-adv private storage for ARP entries exchanged within DAT.
This storage will represent the node local cache in the DAT protocol.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Add all the relevant functions in order to manage a Distributed Hash Table over
the B.A.T.M.A.N.-adv network. It will later be used to store several ARP entries
and implement DAT (Distributed ARP Table)
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Threads in the bottom half of batadv_bla_check_bcast_duplist() might
otherwise for instance overwrite variables which other threads might
be using/reading at the same time in the top half, potentially
leading to messing up the bcast_duplist, possibly resulting in false
bridge loop avoidance duplicate check decisions.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
With the current TT mechanism a new client joining the network is not
immediately able to communicate with other hosts because its MAC address has not
been announced yet. This situation holds until the first OGM containing its
joining event will be spread over the mesh network.
This behaviour can be acceptable in networks where the originator interval is a
small value (e.g. 1sec) but if that value is set to an higher time (e.g. 5secs)
the client could suffer from several malfunctions like DHCP client timeouts,
etc.
This patch adds an early detection mechanism that makes nodes in the network
able to recognise "not yet announced clients" by means of the broadcast packets
they emitted on connection (e.g. ARP or DHCP request). The added client will
then be confirmed upon receiving the OGM claiming it or purged if such OGM
is not received within a fixed amount of time.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The structure batadv_priv grows everytime a new feature is introduced. It gets
hard to find the parts of the struct that belongs to a specific feature. This
becomes even harder by the fact that not every feature uses a prefix in the
member name.
The variables for bridge loop avoidence, gateway handling, translation table
and visualization server are moved into separate structs that are included in
the bat_priv main struct.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The batadv_tt_orig_list_entry structure didn't have any refcounting mechanism so
far. This patch introduces it and makes the structure being usable in much more
complex context.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
batman-adv doesn't follow the style for multiline comments that David S. Miller
prefers. All comments should be reformatted to follow this consistent style to
make the code slightly more readable.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Prior to this patch the translation table code made assumptions about how
the routing protocol works and where its buffers are stored (to directly
modify them).
Each protocol now calls the tt code with the relevant pointers, thereby
abstracting the code.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Added additional counters in a bat_stats structure, which are exported
through the ethtool api. The counters are specific to batman-adv and
includes:
forwarded packets and bytes
management packets and bytes (aggregated OGMs at this point)
translation table packets
New counters are added by extending "enum bat_counters" in types.h and
adding corresponding descriptive string(s) to bat_counters_strings in
soft-iface.c.
Counters are increased by calling batadv_add_counter() and incremented
by one by calling batadv_inc_counter().
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
In the code we neever need to atomically check and set the bat_priv->tt_crc
field value. It is simply set and read once in different pieces of the code.
Therefore this field can be safely be converted from atomic_t to uint16_t.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Antonio Quartulli