After TIPC doesn't depend on iocb argument in its internal
implementations of sendmsg() and recvmsg() hooks defined in proto
structure, no any user is using iocb argument in them at all now.
Then we can drop the redundant iocb argument completely from kinds of
implementations of both sendmsg() and recvmsg() in the entire
networking stack.
Cc: Christoph Hellwig <hch@lst.de>
Suggested-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of an effort to move skb->dropcount to skb->cb[] use a common
macro in protocol families using skb->cb[] for ancillary data to
validate available room in skb->cb[].
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Receive Flow Steering is a nice solution but suffers from
hash collisions when a mix of connected and unconnected traffic
is received on the host, when flow hash table is populated.
Also, clearing flow in inet_release() makes RFS not very good
for short lived flows, as many packets can follow close().
(FIN , ACK packets, ...)
This patch extends the information stored into global hash table
to not only include cpu number, but upper part of the hash value.
I use a 32bit value, and dynamically split it in two parts.
For host with less than 64 possible cpus, this gives 6 bits for the
cpu number, and 26 (32-6) bits for the upper part of the hash.
Since hash bucket selection use low order bits of the hash, we have
a full hash match, if /proc/sys/net/core/rps_sock_flow_entries is big
enough.
If the hash found in flow table does not match, we fallback to RPS (if
it is enabled for the rxqueue).
This means that a packet for an non connected flow can avoid the
IPI through a unrelated/victim CPU.
This also means we no longer have to clear the table at socket
close time, and this helps short lived flows performance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP timestamping introduced MSG_ERRQUEUE handling for TCP sockets.
If the socket is of family AF_INET6, call ipv6_recv_error instead
of ip_recv_error.
This change is more complex than a single branch due to the loadable
ipv6 module. It reuses a pre-existing indirect function call from
ping. The ping code is safe to call, because it is part of the core
ipv6 module and always present when AF_INET6 sockets are active.
Fixes: 4ed2d765 (net-timestamp: TCP timestamping)
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
It may also be worthwhile to add WARN_ON_ONCE(sk->family == AF_INET6)
to ip_recv_error.
Signed-off-by: David S. Miller <davem@davemloft.net>
Device can export MPLS GSO support in dev->mpls_features same way
it export vlan features in dev->vlan_features. So it is safe to
remove NETIF_F_GSO_MPLS redundant flag.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Add a new GSO type, SKB_GSO_TUNNEL_REMCSUM, which indicates remote
checksum offload being done (in this case inner checksum must not
be offloaded to the NIC).
Added logic in __skb_udp_tunnel_segment to handle remote checksum
offload case.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_gso_segment() has a 'features' argument representing offload features
available to the output path.
A few handlers, e.g. GRE, instead re-fetch the features of skb->dev and use
those instead of the provided ones when handing encapsulation/tunnels.
Depending on dev->hw_enc_features of the output device skb_gso_segment() can
then return NULL even when the caller has disabled all GSO feature bits,
as segmentation of inner header thinks device will take care of segmentation.
This e.g. affects the tbf scheduler, which will silently drop GRE-encap GSO skbs
that did not fit the remaining token quota as the segmentation does not work
when device supports corresponding hw offload capabilities.
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Proper CHECKSUM_COMPLETE support needs to adjust skb->csum
when we remove one header. Its done using skb_gro_postpull_rcsum()
In the case of IPv4, we know that the adjustment is not really needed,
because the checksum over IPv4 header is 0. Lets add a comment to
ease code comprehension and avoid copy/paste errors.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The send_check logic was only interesting in cases of TCP offload and
UDP UFO where the checksum needed to be initialized to the pseudo
header checksum. Now we've moved that logic into the related
gso_segment functions so gso_send_check is no longer needed.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add inet_gro_receive and inet_gro_complete to ipip_offload to
support GRO.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net.ipv4.ip_nonlocal_bind sysctl was global to all network
namespaces. This patch allows to set a different value for each
network namespace.
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed a bug that was introduced by my GRE-GRO patch
(bf5a755f5e net-gre-gro: Add GRE
support to the GRO stack) that breaks the forwarding path
because various GSO related fields were not set. The bug will
cause on the egress path either the GSO code to fail, or a
GRE-TSO capable (NETIF_F_GSO_GRE) NICs to choke. The following
fix has been tested for both cases.
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call gso_make_checksum. This should have the benefit of using a
checksum that may have been previously computed for the packet.
This also adds NETIF_F_GSO_GRE_CSUM to differentiate devices that
offload GRE GSO with and without the GRE checksum offloaed.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a new netif feature for GSO_UDP_TUNNEL_CSUM. This indicates
that a device is capable of computing the UDP checksum in the
encapsulating header of a UDP tunnel.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't seem like an protocols are setting anything other
than the default, and allowing to arbitrarily disable checksums
for a whole protocol seems dangerous. This can be done on a per
socket basis.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_local_port_range is already per netns, so should ip_local_reserved_ports
be. And since it is none by default we don't actually need it when we don't
enable CONFIG_SYSCTL.
By the way, rename inet_is_reserved_local_port() to inet_is_local_reserved_port()
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/altera/altera_sgdma.c
net/netlink/af_netlink.c
net/sched/cls_api.c
net/sched/sch_api.c
The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces. These were simple transformations from
netlink_capable to netlink_ns_capable.
The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly, when CONFIG_SYSCTL is not set, ping_group_range should still
work, just that no one can change it. Therefore we should move it out of
sysctl_net_ipv4.c. And, it should not share the same seqlock with
ip_local_port_range.
BTW, rename it to ->ping_group_range instead.
Cc: David S. Miller <davem@davemloft.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Stefan de Konink <stefan@konink.de>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_SYSCTL is not set, ip_local_port_range should still work,
just that no one can change it. Therefore we should move it out of sysctl_inet.c.
Also, rename it to ->ip_local_ports instead.
Cc: David S. Miller <davem@davemloft.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Stefan de Konink <stefan@konink.de>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 8f0ea0fe3a (snmp: reduce percpu needs by 50%)
reduced snmp array size to 1, so technically it doesn't have to be
an array any more. What's more, after the following commit:
commit 933393f58f
Date: Thu Dec 22 11:58:51 2011 -0600
percpu: Remove irqsafe_cpu_xxx variants
We simply say that regular this_cpu use must be safe regardless of
preemption and interrupt state. That has no material change for x86
and s390 implementations of this_cpu operations. However, arches that
do not provide their own implementation for this_cpu operations will
now get code generated that disables interrupts instead of preemption.
probably no arch wants to have SNMP_ARRAY_SZ == 2. At least after
almost 3 years, no one complains.
So, just convert the array to a single pointer and remove snmp_mib_init()
and snmp_mib_free() as well.
Cc: Christoph Lameter <cl@linux.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the bh safe variant with the hard irq safe variant.
We need a hard irq safe variant to deal with netpoll transmitting
packets from hard irq context, and we need it in most if not all of
the places using the bh safe variant.
Except on 32bit uni-processor the code is exactly the same so don't
bother with a bh variant, just have a hard irq safe variant that
everyone can use.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the UFO fragmentation process does not correctly handle inner
UDP frames.
(The following tcpdumps are captured on the parent interface with ufo
disabled while tunnel has ufo enabled, 2000 bytes payload, mtu 1280,
both sit device):
IPv6:
16:39:10.031613 IP (tos 0x0, ttl 64, id 3208, offset 0, flags [DF], proto IPv6 (41), length 1300)
192.168.122.151 > 1.1.1.1: IP6 (hlim 64, next-header Fragment (44) payload length: 1240) 2001::1 > 2001::8: frag (0x00000001:0|1232) 44883 > distinct: UDP, length 2000
16:39:10.031709 IP (tos 0x0, ttl 64, id 3209, offset 0, flags [DF], proto IPv6 (41), length 844)
192.168.122.151 > 1.1.1.1: IP6 (hlim 64, next-header Fragment (44) payload length: 784) 2001::1 > 2001::8: frag (0x00000001:0|776) 58979 > 46366: UDP, length 5471
We can see that fragmentation header offset is not correctly updated.
(fragmentation id handling is corrected by 916e4cf46d ("ipv6: reuse
ip6_frag_id from ip6_ufo_append_data")).
IPv4:
16:39:57.737761 IP (tos 0x0, ttl 64, id 3209, offset 0, flags [DF], proto IPIP (4), length 1296)
192.168.122.151 > 1.1.1.1: IP (tos 0x0, ttl 64, id 57034, offset 0, flags [none], proto UDP (17), length 1276)
192.168.99.1.35961 > 192.168.99.2.distinct: UDP, length 2000
16:39:57.738028 IP (tos 0x0, ttl 64, id 3210, offset 0, flags [DF], proto IPIP (4), length 792)
192.168.122.151 > 1.1.1.1: IP (tos 0x0, ttl 64, id 57035, offset 0, flags [none], proto UDP (17), length 772)
192.168.99.1.13531 > 192.168.99.2.20653: UDP, length 51109
In this case fragmentation id is incremented and offset is not updated.
First, I aligned inet_gso_segment and ipv6_gso_segment:
* align naming of flags
* ipv6_gso_segment: setting skb->encapsulation is unnecessary, as we
always ensure that the state of this flag is left untouched when
returning from upper gso segmenation function
* ipv6_gso_segment: move skb_reset_inner_headers below updating the
fragmentation header data, we don't care for updating fragmentation
header data
* remove currently unneeded comment indicating skb->encapsulation might
get changed by upper gso_segment callback (gre and udp-tunnel reset
encapsulation after segmentation on each fragment)
If we encounter an IPIP or SIT gso skb we now check for the protocol ==
IPPROTO_UDP and that we at least have already traversed another ip(6)
protocol header.
The reason why we have to special case GSO_IPIP and GSO_SIT is that
we reset skb->encapsulation to 0 while skb_mac_gso_segment the inner
protocol of GSO_UDP_TUNNEL or GSO_GRE packets.
Reported-by: Wolfgang Walter <linux@stwm.de>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new ip_no_pmtu_disc mode only allowes fragmentation-needed errors
to be honored by protocols which do more stringent validation on the
ICMP's packet payload. This knob is useful for people who e.g. want to
run an unmodified DNS server in a namespace where they need to use pmtu
for TCP connections (as they are used for zone transfers or fallback
for requests) but don't want to use possibly spoofed UDP pmtu information.
Currently the whitelisted protocols are TCP, SCTP and DCCP as they check
if the returned packet is in the window or if the association is valid.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: John Heffner <johnwheffner@gmail.com>
Suggested-by: Florian Weimer <fweimer@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch built on top of Commit 299603e837
("net-gro: Prepare GRO stack for the upcoming tunneling support") to add
the support of the standard GRE (RFC1701/RFC2784/RFC2890) to the GRO
stack. It also serves as an example for supporting other encapsulation
protocols in the GRO stack in the future.
The patch supports version 0 and all the flags (key, csum, seq#) but
will flush any pkt with the S (seq#) flag. This is because the S flag
is not support by GSO, and a GRO pkt may end up in the forwarding path,
thus requiring GSO support to break it up correctly.
Currently the "packet_offload" structure only contains L3 (ETH_P_IP/
ETH_P_IPV6) GRO offload support so the encapped pkts are limited to
IP pkts (i.e., w/o L2 hdr). But support for other protocol type can
be easily added, so is the support for GRE variations like NVGRE.
The patch also support csum offload. Specifically if the csum flag is on
and the h/w is capable of checksumming the payload (CHECKSUM_COMPLETE),
the code will take advantage of the csum computed by the h/w when
validating the GRE csum.
Note that commit 60769a5dcd "ipv4: gre:
add GRO capability" already introduces GRO capability to IPv4 GRE
tunnels, using the gro_cells infrastructure. But GRO is done after
GRE hdr has been removed (i.e., decapped). The following patch applies
GRO when pkts first come in (before hitting the GRE tunnel code). There
is some performance advantage for applying GRO as early as possible.
Also this approach is transparent to other subsystem like Open vSwitch
where GRE decap is handled outside of the IP stack hence making it
harder for the gro_cells stuff to apply. On the other hand, some NICs
are still not capable of hashing on the inner hdr of a GRE pkt (RSS).
In that case the GRO processing of pkts from the same remote host will
all happen on the same CPU and the performance may be suboptimal.
I'm including some rough preliminary performance numbers below. Note
that the performance will be highly dependent on traffic load, mix as
usual. Moreover it also depends on NIC offload features hence the
following is by no means a comprehesive study. Local testing and tuning
will be needed to decide the best setting.
All tests spawned 50 copies of netperf TCP_STREAM and ran for 30 secs.
(super_netperf 50 -H 192.168.1.18 -l 30)
An IP GRE tunnel with only the key flag on (e.g., ip tunnel add gre1
mode gre local 10.246.17.18 remote 10.246.17.17 ttl 255 key 123)
is configured.
The GRO support for pkts AFTER decap are controlled through the device
feature of the GRE device (e.g., ethtool -K gre1 gro on/off).
1.1 ethtool -K gre1 gro off; ethtool -K eth0 gro off
thruput: 9.16Gbps
CPU utilization: 19%
1.2 ethtool -K gre1 gro on; ethtool -K eth0 gro off
thruput: 5.9Gbps
CPU utilization: 15%
1.3 ethtool -K gre1 gro off; ethtool -K eth0 gro on
thruput: 9.26Gbps
CPU utilization: 12-13%
1.4 ethtool -K gre1 gro on; ethtool -K eth0 gro on
thruput: 9.26Gbps
CPU utilization: 10%
The following tests were performed on a different NIC that is capable of
csum offload. I.e., the h/w is capable of computing IP payload csum
(CHECKSUM_COMPLETE).
2.1 ethtool -K gre1 gro on (hence will use gro_cells)
2.1.1 ethtool -K eth0 gro off; csum offload disabled
thruput: 8.53Gbps
CPU utilization: 9%
2.1.2 ethtool -K eth0 gro off; csum offload enabled
thruput: 8.97Gbps
CPU utilization: 7-8%
2.1.3 ethtool -K eth0 gro on; csum offload disabled
thruput: 8.83Gbps
CPU utilization: 5-6%
2.1.4 ethtool -K eth0 gro on; csum offload enabled
thruput: 8.98Gbps
CPU utilization: 5%
2.2 ethtool -K gre1 gro off
2.2.1 ethtool -K eth0 gro off; csum offload disabled
thruput: 5.93Gbps
CPU utilization: 9%
2.2.2 ethtool -K eth0 gro off; csum offload enabled
thruput: 5.62Gbps
CPU utilization: 8%
2.2.3 ethtool -K eth0 gro on; csum offload disabled
thruput: 7.69Gbps
CPU utilization: 8%
2.2.4 ethtool -K eth0 gro on; csum offload enabled
thruput: 8.96Gbps
CPU utilization: 5-6%
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2013-12-19
1) Use the user supplied policy index instead of a generated one
if present. From Fan Du.
2) Make xfrm migration namespace aware. From Fan Du.
3) Make the xfrm state and policy locks namespace aware. From Fan Du.
4) Remove ancient sleeping when the SA is in acquire state,
we now queue packets to the policy instead. This replaces the
sleeping code.
5) Remove FLOWI_FLAG_CAN_SLEEP. This was used to notify xfrm about the
posibility to sleep. The sleeping code is gone, so remove it.
6) Check user specified spi for IPComp. Thr spi for IPcomp is only
16 bit wide, so check for a valid value. From Fan Du.
7) Export verify_userspi_info to check for valid user supplied spi ranges
with pfkey and netlink. From Fan Du.
8) RFC3173 states that if the total size of a compressed payload and the IPComp
header is not smaller than the size of the original payload, the IP datagram
must be sent in the original non-compressed form. These packets are dropped
by the inbound policy check because they are not transformed. Document the need
to set 'level use' for IPcomp to receive such packets anyway. From Fan Du.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The other field in ipv4_config, log_martians, was converted to a
per-interface setting, so we can just remove the whole structure.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the GRO stack to avoid the use of "network_header"
and associated macros like ip_hdr() and ipv6_hdr() in order to allow
an arbitary number of IP hdrs (v4 or v6) to be used in the
encapsulation chain. This lays the foundation for various IP
tunneling support (IP-in-IP, GRE, VXLAN, SIT,...) to be added later.
With this patch, the GRO stack traversing now is mostly based on
skb_gro_offset rather than special hdr offsets saved in skb (e.g.,
skb->network_header). As a result all but the top layer (i.e., the
the transport layer) must have hdrs of the same length in order for
a pkt to be considered for aggregation. Therefore when adding a new
encap layer (e.g., for tunneling), one must check and skip flows
(e.g., by setting NAPI_GRO_CB(p)->same_flow to 0) that have a
different hdr length.
Note that unlike the network header, the transport header can and
will continue to be set by the GRO code since there will be at
most one "transport layer" in the encap chain.
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FLOWI_FLAG_CAN_SLEEP was used to notify xfrm about the posibility
to sleep until the needed states are resolved. This code is gone,
so FLOWI_FLAG_CAN_SLEEP is not needed anymore.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Pull core locking changes from Ingo Molnar:
"The biggest changes:
- add lockdep support for seqcount/seqlocks structures, this
unearthed both bugs and required extra annotation.
- move the various kernel locking primitives to the new
kernel/locking/ directory"
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
block: Use u64_stats_init() to initialize seqcounts
locking/lockdep: Mark __lockdep_count_forward_deps() as static
lockdep/proc: Fix lock-time avg computation
locking/doc: Update references to kernel/mutex.c
ipv6: Fix possible ipv6 seqlock deadlock
cpuset: Fix potential deadlock w/ set_mems_allowed
seqcount: Add lockdep functionality to seqcount/seqlock structures
net: Explicitly initialize u64_stats_sync structures for lockdep
locking: Move the percpu-rwsem code to kernel/locking/
locking: Move the lglocks code to kernel/locking/
locking: Move the rwsem code to kernel/locking/
locking: Move the rtmutex code to kernel/locking/
locking: Move the semaphore core to kernel/locking/
locking: Move the spinlock code to kernel/locking/
locking: Move the lockdep code to kernel/locking/
locking: Move the mutex code to kernel/locking/
hung_task debugging: Add tracepoint to report the hang
x86/locking/kconfig: Update paravirt spinlock Kconfig description
lockstat: Report avg wait and hold times
lockdep, x86/alternatives: Drop ancient lockdep fixup message
...
While testing virtio_net and skb_segment() changes, Hannes reported
that UFO was sending wrong frames.
It appears this was introduced by a recent commit :
8c3a897bfa ("inet: restore gso for vxlan")
The old condition to perform IP frag was :
tunnel = !!skb->encapsulation;
...
if (!tunnel && proto == IPPROTO_UDP) {
So the new one should be :
udpfrag = !skb->encapsulation && proto == IPPROTO_UDP;
...
if (udpfrag) {
Initialization of udpfrag must be done before call
to ops->callbacks.gso_segment(skb, features), as
skb_udp_tunnel_segment() clears skb->encapsulation
(We want udpfrag to be true for UFO, false for VXLAN)
With help from Alexei Starovoitov
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to enable lockdep on seqcount/seqlock structures, we
must explicitly initialize any locks.
The u64_stats_sync structure, uses a seqcount, and thus we need
to introduce a u64_stats_init() function and use it to initialize
the structure.
This unfortunately adds a lot of fairly trivial initialization code
to a number of drivers. But the benefit of ensuring correctness makes
this worth while.
Because these changes are required for lockdep to be enabled, and the
changes are quite trivial, I've not yet split this patch out into 30-some
separate patches, as I figured it would be better to get the various
maintainers thoughts on how to best merge this change along with
the seqcount lockdep enablement.
Feedback would be appreciated!
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: James Morris <jmorris@namei.org>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Roger Luethi <rl@hellgate.ch>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Simon Horman <horms@verge.net.au>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Wensong Zhang <wensong@linux-vs.org>
Cc: netdev@vger.kernel.org
Link: http://lkml.kernel.org/r/1381186321-4906-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Alexei reported a performance regression on vxlan, caused
by commit 3347c96029 "ipv4: gso: make inet_gso_segment() stackable"
GSO vxlan packets were not properly segmented, adding IP fragments
while they were not expected.
Rename 'bool tunnel' to 'bool encap', and add a new boolean
to express the fact that UDP should be fragmented.
This fragmentation is triggered by skb->encapsulation being set.
Remove a "skb->encapsulation = 1" added in above commit,
as its not needed, as frags inherit skb->frag from original
GSO skb.
Reported-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now ipv6_gso_segment() is stackable, its relatively easy to
implement GSO/TSO support for SIT tunnels
Performance results, when segmentation is done after tunnel
device (as no NIC is yet enabled for TSO SIT support) :
Before patch :
lpq84:~# ./netperf -H 2002:af6:1153:: -Cc
MIGRATED TCP STREAM TEST from ::0 (::) port 0 AF_INET6 to 2002:af6:1153:: () port 0 AF_INET6
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB
87380 16384 16384 10.00 3168.31 4.81 4.64 2.988 2.877
After patch :
lpq84:~# ./netperf -H 2002:af6:1153:: -Cc
MIGRATED TCP STREAM TEST from ::0 (::) port 0 AF_INET6 to 2002:af6:1153:: () port 0 AF_INET6
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB
87380 16384 16384 10.00 5525.00 7.76 5.17 2.763 1.840
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code that is implemented is per memory cgroup not per netns, and
having per netns bits is just confusing. Remove the per netns bits to
make it easier to see what is really going on.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize the ehash and ipv6_hash_secrets with net_get_random_once.
Each compilation unit gets its own secret now:
ipv4/inet_hashtables.o
ipv4/udp.o
ipv6/inet6_hashtables.o
ipv6/udp.o
rds/connection.o
The functions still get inlined into the hashing functions. In the fast
path we have at most two (needed in ipv6) if (unlikely(...)).
Cc: Eric Dumazet <edumazet@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now inet_gso_segment() is stackable, its relatively easy to
implement GSO/TSO support for IPIP
Performance results, when segmentation is done after tunnel
device (as no NIC is yet enabled for TSO IPIP support) :
Before patch :
lpq83:~# ./netperf -H 7.7.9.84 -Cc
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.9.84 () port 0 AF_INET
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB
87380 16384 16384 10.00 3357.88 5.09 3.70 2.983 2.167
After patch :
lpq83:~# ./netperf -H 7.7.9.84 -Cc
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.9.84 () port 0 AF_INET
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB
87380 16384 16384 10.00 7710.19 4.52 6.62 1.152 1.687
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support GSO on IPIP, we need to make
inet_gso_segment() stackable.
It should not assume network header starts right after mac
header.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_gso_segment() and inet_gso_send_check() are called by
skb_mac_gso_segment() under rcu lock, no need to use
rcu_read_lock() / rcu_read_unlock()
Avoid calling ip_hdr() twice per function.
We can use ip_send_check() helper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The removal of the routing cache introduced a performance regression for
some UDP workloads since a dst lookup must be done for each packet.
This change caches the dst per socket in a similar manner to what we do
for TCP by implementing early_demux.
For UDP multicast we can only cache the dst if there is only one
receiving socket on the host. Since caching only works when there is
one receiving socket we do the multicast socket lookup using RCU.
For UDP unicast we only demux sockets with an exact match in order to
not break forwarding setups. Additionally since the hash chains may be
long we only check the first socket to see if it is a match and not
waste extra time searching the whole chain when we might not find an
exact match.
Benchmark results from a netperf UDP_RR test:
Before 87961.22 transactions/s
After 89789.68 transactions/s
Benchmark results from a fio 1 byte UDP multicast pingpong test
(Multicast one way unicast response):
Before 12.97us RTT
After 12.63us RTT
Signed-off-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A host might need net_secret[] and never open a single socket.
Problem added in commit aebda156a5
("net: defer net_secret[] initialization")
Based on prior patch from Hannes Frederic Sowa.
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@strressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fengguang reported:
net/built-in.o: In function `in6_dev_finish_destroy':
(.text+0x4ca7d): undefined reference to `snmp_mib_free'
this is due to snmp_mib_free() is defined when CONFIG_INET is enabled,
but in6_dev_finish_destroy() is now moved to core kernel.
I think snmp_mib_free() is small enough to be inlined, so just make it
static inline.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following sparse error :
net/ipv4/af_inet.c:1410:59: warning: restricted __be16 degrades to
integer
added in commit db8caf3dbc
("gro: should aggregate frames without DF")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
From: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to TCP offloading and UDPv6 offloading, move all related
UDPv4 functions to udp_offload.c to make things more explicit. Also,
by this, we can make those functions static.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Would be good to make things explicit and move those functions to
a new file called tcp_offload.c, thus make this similar to tcpv6_offload.c.
While moving all related functions into tcp_offload.c, we can also
make some of them static, since they are only used there. Also, add
an explicit registration function.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRO on IPv4 doesn't aggregate frames if they don't have DF bit set.
Some servers use IP_MTU_DISCOVER/IP_PMTUDISC_PROBE, so linux receivers
are unable to aggregate this kind of traffic.
The right thing to do is to allow aggregation as long as the DF bit has
same value on all segments.
bnx2x LRO does this correctly.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jerry Chu <hkchu@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case where a non-MPLS packet is received and an MPLS stack is
added it may well be the case that the original skb is GSO but the
NIC used for transmit does not support GSO of MPLS packets.
The aim of this code is to provide GSO in software for MPLS packets
whose skbs are GSO.
SKB Usage:
When an implementation adds an MPLS stack to a non-MPLS packet it should do
the following to skb metadata:
* Set skb->inner_protocol to the old non-MPLS ethertype of the packet.
skb->inner_protocol is added by this patch.
* Set skb->protocol to the new MPLS ethertype of the packet.
* Set skb->network_header to correspond to the
end of the L3 header, including the MPLS label stack.
I have posted a patch, "[PATCH v3.29] datapath: Add basic MPLS support to
kernel" which adds MPLS support to the kernel datapath of Open vSwtich.
That patch sets the above requirements in datapath/actions.c:push_mpls()
and was used to exercise this code. The datapath patch is against the Open
vSwtich tree but it is intended that it be added to the Open vSwtich code
present in the mainline Linux kernel at some point.
Features:
I believe that the approach that I have taken is at least partially
consistent with the handling of other protocols. Jesse, I understand that
you have some ideas here. I am more than happy to change my implementation.
This patch adds dev->mpls_features which may be used by devices
to advertise features supported for MPLS packets.
A new NETIF_F_MPLS_GSO feature is added for devices which support
hardware MPLS GSO offload. Currently no devices support this
and MPLS GSO always falls back to software.
Alternate Implementation:
One possible alternate implementation is to teach netif_skb_features()
and skb_network_protocol() about MPLS, in a similar way to their
understanding of VLANs. I believe this would avoid the need
for net/mpls/mpls_gso.c and in particular the calls to
__skb_push() and __skb_push() in mpls_gso_segment().
I have decided on the implementation in this patch as it should
not introduce any overhead in the case where mpls_gso is not compiled
into the kernel or inserted as a module.
MPLS GSO suggested by Jesse Gross.
Based in part on "v4 GRE: Add TCP segmentation offload for GRE"
by Pravin B Shelar.
Cc: Jesse Gross <jesse@nicira.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ipv6 traffic, GRE can generate packet with strange GSO
bits, e.g. ipv4 packet with SKB_GSO_TCPV6 flag set. Therefore
following patch relaxes check in inet gso handler to allow
such packet for segmentation.
This patch also fixes wrong skb->protocol set that was done in
gre_gso_segment() handler.
Reported-by: Steinar H. Gunderson <sesse@google.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of feeding net_secret[] at boot time, defer the init
at the point first socket is created.
This permits some platforms to use better entropy sources than
the ones available at boot time.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch refactors GRE code into ip tunneling code and GRE
specific code. Common tunneling code is moved to ip_tunnel module.
ip_tunnel module is written as generic library which can be used
by different tunneling implementations.
ip_tunnel module contains following components:
- packet xmit and rcv generic code. xmit flow looks like
(gre_xmit/ipip_xmit)->ip_tunnel_xmit->ip_local_out.
- hash table of all devices.
- lookup for tunnel devices.
- control plane operations like device create, destroy, ioctl, netlink
operations code.
- registration for tunneling modules, like gre, ipip etc.
- define single pcpu_tstats dev->tstats.
- struct tnl_ptk_info added to pass parsed tunnel packet parameters.
ipip.h header is renamed to ip_tunnel.h
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip-header id needs to be incremented even if IP_DF flag is set.
This behaviour was changed in commit 490ab08127
(IP_GRE: Fix IP-Identification).
Following patch fixes it so that identification is always
incremented.
Reported-by: Cong Wang <amwang@redhat.com>
Acked-by: Cong Wang <amwang@redhat.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Adds generic tunneling offloading support for IPv4-UDP based
tunnels.
GSO type is added to request this offload for a skb.
netdev feature NETIF_F_UDP_TUNNEL is added for hardware offloaded
udp-tunnel support. Currently no device supports this feature,
software offload is used.
This can be used by tunneling protocols like VXLAN.
CC: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Earlier SG was unset if CSUM was not available for given device to
force skb copy to avoid sending inconsistent csum.
Commit c9af6db4c1 (net: Fix possible wrong checksum generation)
added explicit flag to force copy to fix this issue. Therefore
there is no need to link SG and CSUM, following patch kills this
link between there two features.
This patch is also required following patch in series.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRE-GSO generates ip fragments with id 0,2,3,4... for every
GSO packet, which is not correct. Following patch fixes it
by setting ip-header id unique id of fragments are allowed.
As Eric Dumazet suggested it is optimized by using inner ip-header
whenever inner packet is ipv4.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we handle icmp errors in each transport protocol's err_handler,
for icmp protocols, that is ping_err. Since this handler only care
of those icmp errors triggered by echo request, errors triggered
by echo reply(which sent by kernel) are sliently ignored.
So wrap ping_err() with icmp_err() to deal with those icmp errors.
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like its possible to open thousands of TCP IPv6
sessions on a server, all landing in a single slot of TCP hash
table. Incoming packets have to lookup sockets in a very
long list.
We should hash all bits from foreign IPv6 addresses, using
a salt and hash mix, not a simple XOR.
inet6_ehashfn() can also separately use the ports, instead
of xoring them.
Reported-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch adds GRE protocol offload handler so that
skb_gso_segment() can segment GRE packets.
SKB GSO CB is added to keep track of total header length so that
skb_segment can push entire header. e.g. in case of GRE, skb_segment
need to push inner and outer headers to every segment.
New NETIF_F_GRE_GSO feature is added for devices which support HW
GRE TSO offload. Currently none of devices support it therefore GRE GSO
always fall backs to software GSO.
[ Compute pkt_len before ip_local_out() invocation. -DaveM ]
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch cef401de7b (net: fix possible wrong checksum
generation) fixed wrong checksum calculation but it broke TSO by
defining new GSO type but not a netdev feature for that type.
net_gso_ok() would not allow hardware checksum/segmentation
offload of such packets without the feature.
Following patch fixes TSO and wrong checksum. This patch uses
same logic that Eric Dumazet used. Patch introduces new flag
SKBTX_SHARED_FRAG if at least one frag can be modified by
the user. but SKBTX_SHARED_FRAG flag is kept in skb shared
info tx_flags rather than gso_type.
tx_flags is better compared to gso_type since we can have skb with
shared frag without gso packet. It does not link SHARED_FRAG to
GSO, So there is no need to define netdev feature for this.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All in-tree ipv4 protocol implementations are now namespace
aware. Therefore all the run-time checks are superfluous.
Reject registry of any non-namespace aware ipv4 protocol.
Eventually we'll remove prot->netns_ok and this registry
time check as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin Shelar mentioned that GSO could potentially generate
wrong TX checksum if skb has fragments that are overwritten
by the user between the checksum computation and transmit.
He suggested to linearize skbs but this extra copy can be
avoided for normal tcp skbs cooked by tcp_sendmsg().
This patch introduces a new SKB_GSO_SHARED_FRAG flag, set
in skb_shinfo(skb)->gso_type if at least one frag can be
modified by the user.
Typical sources of such possible overwrites are {vm}splice(),
sendfile(), and macvtap/tun/virtio_net drivers.
Tested:
$ netperf -H 7.7.8.84
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
7.7.8.84 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 3959.52
$ netperf -H 7.7.8.84 -t TCP_SENDFILE
TCP SENDFILE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.8.84 ()
port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 3216.80
Performance of the SENDFILE is impacted by the extra allocation and
copy, and because we use order-0 pages, while the TCP_STREAM uses
bigger pages.
Reported-by: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow privileged users in any user namespace to bind to
privileged sockets in network namespaces they control.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow an unpriviled user who has created a user namespace, and then
created a network namespace to effectively use the new network
namespace, by reducing capable(CAP_NET_ADMIN) and
capable(CAP_NET_RAW) calls to be ns_capable(net->user_ns,
CAP_NET_ADMIN), or capable(net->user_ns, CAP_NET_RAW) calls.
Settings that merely control a single network device are allowed.
Either the network device is a logical network device where
restrictions make no difference or the network device is hardware NIC
that has been explicity moved from the initial network namespace.
In general policy and network stack state changes are allowed
while resource control is left unchanged.
Allow creating raw sockets.
Allow the SIOCSARP ioctl to control the arp cache.
Allow the SIOCSIFFLAG ioctl to allow setting network device flags.
Allow the SIOCSIFADDR ioctl to allow setting a netdevice ipv4 address.
Allow the SIOCSIFBRDADDR ioctl to allow setting a netdevice ipv4 broadcast address.
Allow the SIOCSIFDSTADDR ioctl to allow setting a netdevice ipv4 destination address.
Allow the SIOCSIFNETMASK ioctl to allow setting a netdevice ipv4 netmask.
Allow the SIOCADDRT and SIOCDELRT ioctls to allow adding and deleting ipv4 routes.
Allow the SIOCADDTUNNEL, SIOCCHGTUNNEL and SIOCDELTUNNEL ioctls for
adding, changing and deleting gre tunnels.
Allow the SIOCADDTUNNEL, SIOCCHGTUNNEL and SIOCDELTUNNEL ioctls for
adding, changing and deleting ipip tunnels.
Allow the SIOCADDTUNNEL, SIOCCHGTUNNEL and SIOCDELTUNNEL ioctls for
adding, changing and deleting ipsec virtual tunnel interfaces.
Allow setting the MRT_INIT, MRT_DONE, MRT_ADD_VIF, MRT_DEL_VIF, MRT_ADD_MFC,
MRT_DEL_MFC, MRT_ASSERT, MRT_PIM, MRT_TABLE socket options on multicast routing
sockets.
Allow setting and receiving IPOPT_CIPSO, IP_OPT_SEC, IP_OPT_SID and
arbitrary ip options.
Allow setting IP_SEC_POLICY/IP_XFRM_POLICY ipv4 socket option.
Allow setting the IP_TRANSPARENT ipv4 socket option.
Allow setting the TCP_REPAIR socket option.
Allow setting the TCP_CONGESTION socket option.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the offload callbacks into its own structure.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since GSO/GRO support is now separated, make IPv4 GSO a
stand-alone init call and not part of inet_init().
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch IPv4 code base to using the new GRO/GSO calls and data.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new data structure for IPv4 protocols that holds GRO/GSO
callbacks and a new array to track the protocols that register GRO/GSO.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to using the new GSO/GRO registration mechanism and new
packet offload structure.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Acked-by: H.K. Jerry Chu <hkchu@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch builds on top of the previous patch to add the support
for TFO listeners. This includes -
1. allocating, properly initializing, and managing the per listener
fastopen_queue structure when TFO is enabled
2. changes to the inet_csk_accept code to support TFO. E.g., the
request_sock can no longer be freed upon accept(), not until 3WHS
finishes
3. allowing a TCP_SYN_RECV socket to properly poll() and sendmsg()
if it's a TFO socket
4. properly closing a TFO listener, and a TFO socket before 3WHS
finishes
5. supporting TCP_FASTOPEN socket option
6. modifying tcp_check_req() to use to check a TFO socket as well
as request_sock
7. supporting TCP's TFO cookie option
8. adding a new SYN-ACK retransmit handler to use the timer directly
off the TFO socket rather than the listener socket. Note that TFO
server side will not retransmit anything other than SYN-ACK until
the 3WHS is completed.
The patch also contains an important function
"reqsk_fastopen_remove()" to manage the somewhat complex relation
between a listener, its request_sock, and the corresponding child
socket. See the comment above the function for the detail.
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing TCP ECN tests, I discovered GRO was reordering packets if it
receives one packet with CE set, while previous packets in same NAPI run
have ECT(0) for the same flow :
09:25:25.857620 IP (tos 0x2,ECT(0), ttl 64, id 27893, offset 0, flags
[DF], proto TCP (6), length 4396)
172.30.42.19.54550 > 172.30.42.13.44139: Flags [.], seq
233801:238145, ack 1, win 115, options [nop,nop,TS val 3397779 ecr
1990627], length 4344
09:25:25.857626 IP (tos 0x3,CE, ttl 64, id 27892, offset 0, flags [DF],
proto TCP (6), length 1500)
172.30.42.19.54550 > 172.30.42.13.44139: Flags [.], seq
232353:233801, ack 1, win 115, options [nop,nop,TS val 3397779 ecr
1990627], length 1448
09:25:25.857638 IP (tos 0x0, ttl 64, id 34581, offset 0, flags [DF],
proto TCP (6), length 64)
172.30.42.13.44139 > 172.30.42.19.54550: Flags [.], cksum 0xac8f
(incorrect -> 0xca69), ack 232353, win 1271, options [nop,nop,TS val
1990627 ecr 3397779,nop,nop,sack 1 {233801:238145}], length 0
We have two problems here :
1) GRO reorders packets
If NIC gave packet1, then packet2, which happen to be from "different
flows" GRO feeds stack with packet2, then packet1. I have yet to
understand how to solve this problem.
2) GRO is not ECN friendly
Delivering packets out of order makes TCP stack not as fast as it could
be.
In this patch I suggest we make the tos test not part of the 'same_flow'
determination, but part of the 'should flush' logic
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
sendmsg() (or sendto()) with MSG_FASTOPEN is a combo of connect(2)
and write(2). The application should replace connect() with it to
send data in the opening SYN packet.
For blocking socket, sendmsg() blocks until all the data are buffered
locally and the handshake is completed like connect() call. It
returns similar errno like connect() if the TCP handshake fails.
For non-blocking socket, it returns the number of bytes queued (and
transmitted in the SYN-data packet) if cookie is available. If cookie
is not available, it transmits a data-less SYN packet with Fast Open
cookie request option and returns -EINPROGRESS like connect().
Using MSG_FASTOPEN on connecting or connected socket will result in
simlar errno like repeating connect() calls. Therefore the application
should only use this flag on new sockets.
The buffer size of sendmsg() is independent of the MSS of the connection.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements sending SYN-data in tcp_connect(). The data is
from tcp_sendmsg() with flag MSG_FASTOPEN (implemented in a later patch).
The length of the cookie in tcp_fastopen_req, init'd to 0, controls the
type of the SYN. If the cookie is not cached (len==0), the host sends
data-less SYN with Fast Open cookie request option to solicit a cookie
from the remote. If cookie is not available (len > 0), the host sends
a SYN-data with Fast Open cookie option. If cookie length is negative,
the SYN will not include any Fast Open option (for fall back operations).
To deal with middleboxes that may drop SYN with data or experimental TCP
option, the SYN-data is only sent once. SYN retransmits do not include
data or Fast Open options. The connection will fall back to regular TCP
handshake.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Input packet processing for local sockets involves two major demuxes.
One for the route and one for the socket.
But we can optimize this down to one demux for certain kinds of local
sockets.
Currently we only do this for established TCP sockets, but it could
at least in theory be expanded to other kinds of connections.
If a TCP socket is established then it's identity is fully specified.
This means that whatever input route was used during the three-way
handshake must work equally well for the rest of the connection since
the keys will not change.
Once we move to established state, we cache the receive packet's input
route to use later.
Like the existing cached route in sk->sk_dst_cache used for output
packets, we have to check for route invalidations using dst->obsolete
and dst->ops->check().
Early demux occurs outside of a socket locked section, so when a route
invalidation occurs we defer the fixup of sk->sk_rx_dst until we are
actually inside of established state packet processing and thus have
the socket locked.
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't pretend that inet_protos[] and inet6_protos[] are hashes, thay
are just a straight arrays. Remove all unnecessary hash masking.
Document MAX_INET_PROTOS.
Use RAW_HTABLE_SIZE when appropriate.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding casts of objects to the same type is unnecessary
and confusing for a human reader.
For example, this cast:
int y;
int *p = (int *)&y;
I used the coccinelle script below to find and remove these
unnecessary casts. I manually removed the conversions this
script produces of casts with __force and __user.
@@
type T;
T *p;
@@
- (T *)p
+ p
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Name them in a "backward compatible" manner, i.e. reuse or not
are still 1 and 0 respectively. The reuse value of 2 means that
the socket with it will forcibly reuse everyone else's port.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix checkpatch errors of the following type:
* ERROR: "foo * bar" should be "foo *bar"
* ERROR: "(foo*)" should be "(foo *)"
Signed-off-by: Daniel Baluta <dbaluta@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
Add #define pr_fmt(fmt) as appropriate.
Add "IPv4: ", "TCP: ", and "IPsec: " to appropriate files.
Standardize on "UDPLite: " for appropriate uses.
Some prefixes were previously "UDPLITE: " and "UDP-Lite: ".
Add KBUILD_MODNAME ": " to icmp and gre.
Remove embedded prefixes as appropriate.
Add missing "\n" to pr_info in gre.c.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more current kernel messaging style.
Convert a printk block to print_hex_dump.
Coalesce formats, align arguments.
Use %s, __func__ instead of embedding function names.
Some messages that were prefixed with <foo>_close are
now prefixed with <foo>_fini. Some ah4 and esp messages
are now not prefixed with "ip ".
The intent of this patch is to later add something like
#define pr_fmt(fmt) "IPv4: " fmt.
to standardize the output messages.
Text size is trivially reduced. (x86-32 allyesconfig)
$ size net/ipv4/built-in.o*
text data bss dec hex filename
887888 31558 249696 1169142 11d6f6 net/ipv4/built-in.o.new
887934 31558 249800 1169292 11d78c net/ipv4/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, it is not easily possible to get TOS/DSCP value of packets from
an incoming TCP stream. The mechanism is there, IP_PKTOPTIONS getsockopt
with IP_RECVTOS set, the same way as incoming TTL can be queried. This is
not actually implemented for TOS, though.
This patch adds this functionality, both for IPv4 (IP_PKTOPTIONS) and IPv6
(IPV6_2292PKTOPTIONS). For IPv4, like in the IP_RECVTTL case, the value of
the TOS field is stored from the other party's ACK.
This is needed for proxies which require DSCP transparency. One such example
is at http://zph.bratcheda.org/.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows each namespace to independently set up
its levels for tcp memory pressure thresholds. This patch
alone does not buy much: we need to make this values
per group of process somehow. This is achieved in the
patches that follows in this patchset.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
CC: David S. Miller <davem@davemloft.net>
CC: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading /proc/net/snmp on a machine with a lot of cpus is very expensive
(can be ~88000 us).
This is because ICMPMSG MIB uses 4096 bytes per cpu, and folding values
for all possible cpus can read 16 Mbytes of memory.
ICMP messages are not considered as fast path on a typical server, and
eventually few cpus handle them anyway. We can afford an atomic
operation instead of using percpu data.
This saves 4096 bytes per cpu and per network namespace.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv4: compat_ioctl is local to af_inet.c, make it static
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit d0733d2e29 (Check for mistakenly passed in non-IPv4 address)
added regression on legacy apps that use bind() with AF_UNSPEC family.
Relax the check, but make sure the bind() is done on INADDR_ANY
addresses, as AF_UNSPEC has probably no sane meaning for other
addresses.
Bugzilla reference : https://bugzilla.kernel.org/show_bug.cgi?id=42012
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-and-bisected-by: Rene Meier <r_meier@freenet.de>
CC: Marcus Meissner <meissner@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi,
Reinhard Max also pointed out that the error should EAFNOSUPPORT according
to POSIX.
The Linux manpages have it as EINVAL, some other OSes (Minix, HPUX, perhaps BSD) use
EAFNOSUPPORT. Windows uses WSAEFAULT according to MSDN.
Other protocols error values in their af bind() methods in current mainline git as far
as a brief look shows:
EAFNOSUPPORT: atm, appletalk, l2tp, llc, phonet, rxrpc
EINVAL: ax25, bluetooth, decnet, econet, ieee802154, iucv, netlink, netrom, packet, rds, rose, unix, x25,
No check?: can/raw, ipv6/raw, irda, l2tp/l2tp_ip
Ciao, Marcus
Signed-off-by: Marcus Meissner <meissner@suse.de>
Cc: Reinhard Max <max@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Le jeudi 16 juin 2011 à 23:38 -0400, David Miller a écrit :
> From: Ben Hutchings <bhutchings@solarflare.com>
> Date: Fri, 17 Jun 2011 00:50:46 +0100
>
> > On Wed, 2011-06-15 at 04:15 +0200, Eric Dumazet wrote:
> >> @@ -1594,6 +1594,7 @@ int tcp_v4_do_rcv(struct sock *sk, struct sk_buff *skb)
> >> goto discard;
> >>
> >> if (nsk != sk) {
> >> + sock_rps_save_rxhash(nsk, skb->rxhash);
> >> if (tcp_child_process(sk, nsk, skb)) {
> >> rsk = nsk;
> >> goto reset;
> >>
> >
> > I haven't tried this, but it looks reasonable to me.
> >
> > What about IPv6? The logic in tcp_v6_do_rcv() looks very similar.
>
> Indeed ipv6 side needs the same fix.
>
> Eric please add that part and resubmit. And in fact I might stick
> this into net-2.6 instead of net-next-2.6
>
OK, here is the net-2.6 based one then, thanks !
[PATCH v2] net: rfs: enable RFS before first data packet is received
First packet received on a passive tcp flow is not correctly RFS
steered.
One sock_rps_record_flow() call is missing in inet_accept()
But before that, we also must record rxhash when child socket is setup.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Tom Herbert <therbert@google.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
CC: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
SNMP mibs use two percpu arrays, one used in BH context, another in USER
context. With increasing number of cpus in machines, and fact that ipv6
uses per network device ipstats_mib, this is consuming a lot of memory
if many network devices are registered.
commit be281e554e (ipv6: reduce per device ICMP mib sizes) shrinked
percpu needs for ipv6, but we can reduce memory use a bit more.
With recent percpu infrastructure (irqsafe_cpu_inc() ...), we no longer
need this BH/USER separation since we can update counters in a single
x86 instruction, regardless of the BH/USER context.
Other arches than x86 might need to disable irq in their
irqsafe_cpu_inc() implementation : If this happens to be a problem, we
can make SNMP_ARRAY_SZ arch dependent, but a previous poll
( https://lkml.org/lkml/2011/3/17/174 ) to arch maintainers did not
raise strong opposition.
Only on 32bit arches, we need to disable BH for 64bit counters updates
done from USER context (currently used for IP MIB)
This also reduces vmlinux size :
1) x86_64 build
$ size vmlinux.before vmlinux.after
text data bss dec hex filename
7853650 1293772 1896448 11043870 a8841e vmlinux.before
7850578 1293772 1896448 11040798 a8781e vmlinux.after
2) i386 build
$ size vmlinux.before vmlinux.afterpatch
text data bss dec hex filename
6039335 635076 3670016 10344427 9dd7eb vmlinux.before
6037342 635076 3670016 10342434 9dd022 vmlinux.afterpatch
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Andi Kleen <andi@firstfloor.org>
CC: Ingo Molnar <mingo@elte.hu>
CC: Tejun Heo <tj@kernel.org>
CC: Christoph Lameter <cl@linux-foundation.org>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org
CC: linux-arch@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Check against mistakenly passing in IPv6 addresses (which would result
in an INADDR_ANY bind) or similar incompatible sockaddrs.
Signed-off-by: Marcus Meissner <meissner@suse.de>
Cc: Reinhard Max <max@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds IPPROTO_ICMP socket kind. It makes it possible to send
ICMP_ECHO messages and receive the corresponding ICMP_ECHOREPLY messages
without any special privileges. In other words, the patch makes it
possible to implement setuid-less and CAP_NET_RAW-less /bin/ping. In
order not to increase the kernel's attack surface, the new functionality
is disabled by default, but is enabled at bootup by supporting Linux
distributions, optionally with restriction to a group or a group range
(see below).
Similar functionality is implemented in Mac OS X:
http://www.manpagez.com/man/4/icmp/
A new ping socket is created with
socket(PF_INET, SOCK_DGRAM, PROT_ICMP)
Message identifiers (octets 4-5 of ICMP header) are interpreted as local
ports. Addresses are stored in struct sockaddr_in. No port numbers are
reserved for privileged processes, port 0 is reserved for API ("let the
kernel pick a free number"). There is no notion of remote ports, remote
port numbers provided by the user (e.g. in connect()) are ignored.
Data sent and received include ICMP headers. This is deliberate to:
1) Avoid the need to transport headers values like sequence numbers by
other means.
2) Make it easier to port existing programs using raw sockets.
ICMP headers given to send() are checked and sanitized. The type must be
ICMP_ECHO and the code must be zero (future extensions might relax this,
see below). The id is set to the number (local port) of the socket, the
checksum is always recomputed.
ICMP reply packets received from the network are demultiplexed according
to their id's, and are returned by recv() without any modifications.
IP header information and ICMP errors of those packets may be obtained
via ancillary data (IP_RECVTTL, IP_RETOPTS, and IP_RECVERR). ICMP source
quenches and redirects are reported as fake errors via the error queue
(IP_RECVERR); the next hop address for redirects is saved to ee_info (in
network order).
socket(2) is restricted to the group range specified in
"/proc/sys/net/ipv4/ping_group_range". It is "1 0" by default, meaning
that nobody (not even root) may create ping sockets. Setting it to "100
100" would grant permissions to the single group (to either make
/sbin/ping g+s and owned by this group or to grant permissions to the
"netadmins" group), "0 4294967295" would enable it for the world, "100
4294967295" would enable it for the users, but not daemons.
The existing code might be (in the unlikely case anyone needs it)
extended rather easily to handle other similar pairs of ICMP messages
(Timestamp/Reply, Information Request/Reply, Address Mask Request/Reply
etc.).
Userspace ping util & patch for it:
http://openwall.info/wiki/people/segoon/ping
For Openwall GNU/*/Linux it was the last step on the road to the
setuid-less distro. A revision of this patch (for RHEL5/OpenVZ kernels)
is in use in Owl-current, such as in the 2011/03/12 LiveCD ISOs:
http://mirrors.kernel.org/openwall/Owl/current/iso/
Initially this functionality was written by Pavel Kankovsky for
Linux 2.4.32, but unfortunately it was never made public.
All ping options (-b, -p, -Q, -R, -s, -t, -T, -M, -I), are tested with
the patch.
PATCH v3:
- switched to flowi4.
- minor changes to be consistent with raw sockets code.
PATCH v2:
- changed ping_debug() to pr_debug().
- removed CONFIG_IP_PING.
- removed ping_seq_fops.owner field (unused for procfs).
- switched to proc_net_fops_create().
- switched to %pK in seq_printf().
PATCH v1:
- fixed checksumming bug.
- CAP_NET_RAW may not create icmp sockets anymore.
RFC v2:
- minor cleanups.
- introduced sysctl'able group range to restrict socket(2).
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two functions must be invoked only when the socket is locked
(because socket identity modifications are made non-atomically).
Therefore we can use the cork flow for output route lookups.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that output route lookups update the flow with
source address selection, we can fetch it from
fl4->saddr instead of rt->rt_src
Signed-off-by: David S. Miller <davem@davemloft.net>
We lack proper synchronization to manipulate inet->opt ip_options
Problem is ip_make_skb() calls ip_setup_cork() and
ip_setup_cork() possibly makes a copy of ipc->opt (struct ip_options),
without any protection against another thread manipulating inet->opt.
Another thread can change inet->opt pointer and free old one under us.
Use RCU to protect inet->opt (changed to inet->inet_opt).
Instead of handling atomic refcounts, just copy ip_options when
necessary, to avoid cache line dirtying.
We cant insert an rcu_head in struct ip_options since its included in
skb->cb[], so this patch is large because I had to introduce a new
ip_options_rcu structure.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions are used together as a unit for route resolution
during connect(). They address the chicken-and-egg problem that
exists when ports need to be allocated during connect() processing,
yet such port allocations require addressing information from the
routing code.
It's currently more heavy handed than it needs to be, and in
particular we allocate and initialize a flow object twice.
Let the callers provide the on-stack flow object. That way we only
need to initialize it once in the ip_route_connect() call.
Later, if ip_route_newports() needs to do anything, it re-uses that
flow object as-is except for the ports which it updates before the
route re-lookup.
Also, describe why this set of facilities are needed and how it works
in a big comment.
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Add const qualifiers to structs iphdr, ipv6hdr and in6_addr pointers
where possible, to make code intention more obvious.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The idea here is this minimizes the number of places one has to edit
in order to make changes to how flows are defined and used.
Signed-off-by: David S. Miller <davem@davemloft.net>
SIOCGETSGCNT is not a unique ioctl value as it it maps tio SIOCPROTOPRIVATE +1,
which unfortunately means the existing infrastructure for compat networking
ioctls is insufficient. A trivial compact ioctl implementation would conflict
with:
SIOCAX25ADDUID
SIOCAIPXPRISLT
SIOCGETSGCNT_IN6
SIOCGETSGCNT
SIOCRSSCAUSE
SIOCX25SSUBSCRIP
SIOCX25SDTEFACILITIES
To make this work I have updated the compat_ioctl decode path to mirror the
the normal ioctl decode path. I have added an ipv4 inet_compat_ioctl function
so that I can have ipv4 specific compat ioctls. I have added a compat_ioctl
function into struct proto so I can break out ioctls by which kind of ip socket
I am using. I have added a compat_raw_ioctl function because SIOCGETSGCNT only
works on raw sockets. I have added a ipmr_compat_ioctl that mirrors the normal
ipmr_ioctl.
This was necessary because unfortunately the struct layout for the SIOCGETSGCNT
has unsigned longs in it so changes between 32bit and 64bit kernels.
This change was sufficient to run a 32bit ip multicast routing daemon on a
64bit kernel.
Reported-by: Bill Fenner <fenner@aristanetworks.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting Ben Hutchings: we presumably won't be defining features that
can only be enabled on 64-bit architectures.
Occurences found by `grep -r` on net/, drivers/net, include/
[ Move features and vlan_features next to each other in
struct netdev, as per Eric Dumazet's suggestion -DaveM ]
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the macros defined for the members of flowi to clean the code up.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now cmpxchg() is available on all arches, we can use it in
build_ehash_secret() and rt_bind_peer() instead of using spinlocks.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
a new boolean flag no_autobind is added to structure proto to avoid the autobind
calls when the protocol is TCP. Then sock_rps_record_flow() is called int the
TCP's sendmsg() and sendpage() pathes.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
----
include/net/inet_common.h | 4 ++++
include/net/sock.h | 1 +
include/net/tcp.h | 8 ++++----
net/ipv4/af_inet.c | 15 +++++++++------
net/ipv4/tcp.c | 11 +++++------
net/ipv4/tcp_ipv4.c | 3 +++
net/ipv6/af_inet6.c | 8 ++++----
net/ipv6/tcp_ipv6.c | 3 +++
8 files changed, 33 insertions(+), 20 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
/proc/net/snmp and /proc/net/netstat expose SNMP counters.
Width of these counters is either 32 or 64 bits, depending on the size
of "unsigned long" in kernel.
This means user program parsing these files must already be prepared to
deal with 64bit values, regardless of user program being 32 or 64 bit.
This patch introduces 64bit snmp values for IPSTAT mib, where some
counters can wrap pretty fast if they are 32bit wide.
# netstat -s|egrep "InOctets|OutOctets"
InOctets: 244068329096
OutOctets: 244069348848
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for 64bit snmp counters for some mibs,
add an 'align' parameter to snmp_mib_init(), instead
of assuming mibs only contain 'unsigned long' fields.
Callers can use __alignof__(type) to provide correct
alignment.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch is implementing IP_NODEFRAG option for IPv4 socket.
The reason is, there's no other way to send out the packet with user
customized header of the reassembly part.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove useless union keyword in rtable, rt6_info and dn_route.
Since there is only one member in a union, the union keyword isn't useful.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(Dropped the infiniband part, because Tetsuo modified the related code,
I will send a separate patch for it once this is accepted.)
This patch introduces /proc/sys/net/ipv4/ip_local_reserved_ports which
allows users to reserve ports for third-party applications.
The reserved ports will not be used by automatic port assignments
(e.g. when calling connect() or bind() with port number 0). Explicit
port allocation behavior is unchanged.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Idea from Eric Dumazet.
As for placement inside of struct sock, I tried to choose a place
that otherwise has a 32-bit hole on 64-bit systems.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Sparse can help us find endianness bugs, but we need to make some
cleanups to be able to more easily spot real bugs.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define a new function to return the waitqueue of a "struct sock".
static inline wait_queue_head_t *sk_sleep(struct sock *sk)
{
return sk->sk_sleep;
}
Change all read occurrences of sk_sleep by a call to this function.
Needed for a future RCU conversion. sk_sleep wont be a field directly
available.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements receive flow steering (RFS). RFS steers
received packets for layer 3 and 4 processing to the CPU where
the application for the corresponding flow is running. RFS is an
extension of Receive Packet Steering (RPS).
The basic idea of RFS is that when an application calls recvmsg
(or sendmsg) the application's running CPU is stored in a hash
table that is indexed by the connection's rxhash which is stored in
the socket structure. The rxhash is passed in skb's received on
the connection from netif_receive_skb. For each received packet,
the associated rxhash is used to look up the CPU in the hash table,
if a valid CPU is set then the packet is steered to that CPU using
the RPS mechanisms.
The convolution of the simple approach is that it would potentially
allow OOO packets. If threads are thrashing around CPUs or multiple
threads are trying to read from the same sockets, a quickly changing
CPU value in the hash table could cause rampant OOO packets--
we consider this a non-starter.
To avoid OOO packets, this solution implements two types of hash
tables: rps_sock_flow_table and rps_dev_flow_table.
rps_sock_table is a global hash table. Each entry is just a CPU
number and it is populated in recvmsg and sendmsg as described above.
This table contains the "desired" CPUs for flows.
rps_dev_flow_table is specific to each device queue. Each entry
contains a CPU and a tail queue counter. The CPU is the "current"
CPU for a matching flow. The tail queue counter holds the value
of a tail queue counter for the associated CPU's backlog queue at
the time of last enqueue for a flow matching the entry.
Each backlog queue has a queue head counter which is incremented
on dequeue, and so a queue tail counter is computed as queue head
count + queue length. When a packet is enqueued on a backlog queue,
the current value of the queue tail counter is saved in the hash
entry of the rps_dev_flow_table.
And now the trick: when selecting the CPU for RPS (get_rps_cpu)
the rps_sock_flow table and the rps_dev_flow table for the RX queue
are consulted. When the desired CPU for the flow (found in the
rps_sock_flow table) does not match the current CPU (found in the
rps_dev_flow table), the current CPU is changed to the desired CPU
if one of the following is true:
- The current CPU is unset (equal to RPS_NO_CPU)
- Current CPU is offline
- The current CPU's queue head counter >= queue tail counter in the
rps_dev_flow table. This checks if the queue tail has advanced
beyond the last packet that was enqueued using this table entry.
This guarantees that all packets queued using this entry have been
dequeued, thus preserving in order delivery.
Making each queue have its own rps_dev_flow table has two advantages:
1) the tail queue counters will be written on each receive, so
keeping the table local to interrupting CPU s good for locality. 2)
this allows lockless access to the table-- the CPU number and queue
tail counter need to be accessed together under mutual exclusion
from netif_receive_skb, we assume that this is only called from
device napi_poll which is non-reentrant.
This patch implements RFS for TCP and connected UDP sockets.
It should be usable for other flow oriented protocols.
There are two configuration parameters for RFS. The
"rps_flow_entries" kernel init parameter sets the number of
entries in the rps_sock_flow_table, the per rxqueue sysfs entry
"rps_flow_cnt" contains the number of entries in the rps_dev_flow
table for the rxqueue. Both are rounded to power of two.
The obvious benefit of RFS (over just RPS) is that it achieves
CPU locality between the receive processing for a flow and the
applications processing; this can result in increased performance
(higher pps, lower latency).
The benefits of RFS are dependent on cache hierarchy, application
load, and other factors. On simple benchmarks, we don't necessarily
see improvement and sometimes see degradation. However, for more
complex benchmarks and for applications where cache pressure is
much higher this technique seems to perform very well.
Below are some benchmark results which show the potential benfit of
this patch. The netperf test has 500 instances of netperf TCP_RR
test with 1 byte req. and resp. The RPC test is an request/response
test similar in structure to netperf RR test ith 100 threads on
each host, but does more work in userspace that netperf.
e1000e on 8 core Intel
No RFS or RPS 104K tps at 30% CPU
No RFS (best RPS config): 290K tps at 63% CPU
RFS 303K tps at 61% CPU
RPC test tps CPU% 50/90/99% usec latency Latency StdDev
No RFS/RPS 103K 48% 757/900/3185 4472.35
RPS only: 174K 73% 415/993/2468 491.66
RFS 223K 73% 379/651/1382 315.61
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With latest CONFIG_PROVE_RCU stuff, I felt more comfortable to make this
work.
sk->sk_dst_cache is currently protected by a rwlock (sk_dst_lock)
This rwlock is readlocked for a very small amount of time, and dst
entries are already freed after RCU grace period. This calls for RCU
again :)
This patch converts sk_dst_lock to a spinlock, and use RCU for readers.
__sk_dst_get() is supposed to be called with rcu_read_lock() or if
socket locked by user, so use appropriate rcu_dereference_check()
condition (rcu_read_lock_held() || sock_owned_by_user(sk))
This patch avoids two atomic ops per tx packet on UDP connected sockets,
for example, and permits sk_dst_lock to be much less dirtied.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
smc91c92_cs: fix the problem of "Unable to find hardware address"
r8169: clean up my printk uglyness
net: Hook up cxgb4 to Kconfig and Makefile
cxgb4: Add main driver file and driver Makefile
cxgb4: Add remaining driver headers and L2T management
cxgb4: Add packet queues and packet DMA code
cxgb4: Add HW and FW support code
cxgb4: Add register, message, and FW definitions
netlabel: Fix several rcu_dereference() calls used without RCU read locks
bonding: fix potential deadlock in bond_uninit()
net: check the length of the socket address passed to connect(2)
stmmac: add documentation for the driver.
stmmac: fix kconfig for crc32 build error
be2net: fix bug in vlan rx path for big endian architecture
be2net: fix flashing on big endian architectures
be2net: fix a bug in flashing the redboot section
bonding: bond_xmit_roundrobin() fix
drivers/net: Add missing unlock
net: gianfar - align BD ring size console messages
net: gianfar - initialize per-queue statistics
...
check the length of the socket address passed to connect(2).
Check the length of the socket address passed to connect(2). If the
length is invalid, -EINVAL will be returned.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
----
net/bluetooth/l2cap.c | 3 ++-
net/bluetooth/rfcomm/sock.c | 3 ++-
net/bluetooth/sco.c | 3 ++-
net/can/bcm.c | 3 +++
net/ieee802154/af_ieee802154.c | 3 +++
net/ipv4/af_inet.c | 5 +++++
net/netlink/af_netlink.c | 3 +++
7 files changed, 20 insertions(+), 3 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
There is no point to align or pad mibs to cache lines, they are per cpu
allocated with a 8 bytes alignment anyway.
This wastes space for no gain. This patch removes __SNMP_MIB_ALIGN__
Since SNMP mibs contain "unsigned long" fields only, we can relax the
allocation alignment from "unsigned long long" to "unsigned long"
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __percpu sparse annotations to net.
These annotations are to make sparse consider percpu variables to be
in a different address space and warn if accessed without going
through percpu accessors. This patch doesn't affect normal builds.
The macro and type tricks around snmp stats make things a bit
interesting. DEFINE/DECLARE_SNMP_STAT() macros mark the target field
as __percpu and SNMP_UPD_PO_STATS() macro is updated accordingly. All
snmp_mib_*() users which used to cast the argument to (void **) are
updated to cast it to (void __percpu **).
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Before calling capable(CAP_NET_RAW) check if this operations is on behalf
of the kernel or on behalf of userspace. Do not do the security check if
it is on behalf of the kernel.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic __sock_create function has a kern argument which allows the
security system to make decisions based on if a socket is being created by
the kernel or by userspace. This patch passes that flag to the
net_proto_family specific create function, so it can do the same thing.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct can_proto had a capability field which wasn't ever used. It is
dropped entirely.
struct inet_protosw had a capability field which can be more clearly
expressed in the code by just checking if sock->type = SOCK_RAW.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
proto_ops->getname implies copying protocol specific data
into storage unit (particulary to __kernel_sockaddr_storage).
So when we implement new protocol support we should keep such
a detail in mind (which is easy to forget about).
Lets introduce DECLARE_SOCKADDR helper which check if
storage unit is not overfowed at build time.
Eventually inet_getname is switched to use DECLARE_SOCKADDR
(to show example of usage).
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to have better cache layouts of struct sock (separate zones
for rx/tx paths), we need this preliminary patch.
Goal is to transfert fields used at lookup time in the first
read-mostly cache line (inside struct sock_common) and move sk_refcnt
to a separate cache line (only written by rx path)
This patch adds inet_ prefix to daddr, rcv_saddr, dport, num, saddr,
sport and id fields. This allows a future patch to define these
fields as macros, like sk_refcnt, without name clashes.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All usages of structure net_proto_ops should be declared const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch against v2.6.31 adds support for route lookup using sk_mark in some
more places. The benefits from this patch are the following.
First, SO_MARK option now has effect on UDP sockets too.
Second, ip_queue_xmit() and inet_sk_rebuild_header() could fail to do routing
lookup correctly if TCP sockets with SO_MARK were used.
Signed-off-by: Atis Elsts <atis@mikrotik.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Remove long removed "inet_protocol_base" declaration.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- validate and forward GSO UDP/IPv4 packets from untrusted sources.
- do software UFO if the outgoing device doesn't support UFO.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_mc_drop_socket() method is declared in linux/igmp.h, which
is included anyhow in af_inet.c. So there is no need for this declaration.
This patch removes it from af_inet.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After some discussion offline with Christoph Lameter and David Stevens
regarding multicast behaviour in Linux, I'm submitting a slightly
modified patch from the one Christoph submitted earlier.
This patch provides a new socket option IP_MULTICAST_ALL.
In this case, default behaviour is _unchanged_ from the current
Linux standard. The socket option is set by default to provide
original behaviour. Sockets wishing to receive data only from
multicast groups they join explicitly will need to clear this
socket option.
Signed-off-by: Nivedita Singhvi <niv@us.ibm.com>
Signed-off-by: Christoph Lameter<cl@linux.com>
Acked-by: David Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch optimises the IPv4 GRO code by using 32-bit loads
(instead of 16-bit ones) on the ID and length checks in the receive
function.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the overwhelming majority of cases, skb_gro_header's return
value cannot be NULL. Yet we must check it because of its current
form. This patch splits it up into multiple functions in order
to avoid this.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_register_protosw() function is responsible for adding a new
inet protocol into a global table (inetsw[]) that is used with RCU rules.
As soon as the store of the pointer is done, other cpus might see
this new protocol in inetsw[], so we have to make sure new protocol
is ready for use. All pending memory updates should thus be committed
to memory before setting the pointer.
This is correctly done using rcu_assign_pointer()
synchronize_net() is typically used at unregister time, after
unsetting the pointer, to make sure no other cpu is still using
the object we want to dismantle. Using it at register time
is only adding an artificial delay that could hide a real bug,
and this bug could popup if/when synchronize_rcu() can proceed
faster than now.
This saves about 13 ms on boot time on a HZ=1000 8 cpus machine ;)
(4 calls to inet_register_protosw(), and about 3200 us per call)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Protocols that use packet_type can be __read_mostly section for better
locality. Elminate any unnecessary initializations of NULL.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This prepares for a real __alloc_percpu, by adding an alignment argument.
Only one place uses __alloc_percpu directly, and that's for a string.
tj: af_inet also uses __alloc_percpu(), update it.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Jens Axboe <axboe@kernel.dk>
As this function can be called more than half a million times for
10GbE, it's important to optimise it as much as we can.
This patch does some obvious changes to use 2-byte and 4-byte
operations instead of byte-oriented ones where possible. Bit
ops are also used to replace logical ops to reduce branching.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_alloc now sets sk_family so this is redundant. In fact it caught
my eye because sock_init_data already uses sk_family so this is too
late anyway.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ying Xue