This clock rate is derived from the PHY PLL, so it should be calculated
dynamically. This calculation is the same as that used by the vendor
kernel and ensures that the escape clock runs at <20MHz as required by
the MIPI specification.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-14-john@metanate.com
Panel drivers may want to sent commands during the disable function, for
example MIPI_DCS_SET_DISPLAY_OFF before the video signal ends. In order
to send commands we need to write to registers, so pclk must be enabled.
While changing this, remove the unnecessary code after the panel
unprepare call which seems to be a workaround for a specific panel and
thus belongs in the panel driver.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-13-john@metanate.com
Some panels need to be configured with commands sent over the MIPI link,
which they will do in the prepare hook. Call this after the PHY has
been initialized so that we are able to send commands to the panel.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-12-john@metanate.com
By dereferencing the MIPI command buffer as a u32* we rely on it being
correctly aligned on ARM, but this may not be the case. Copy it into a
stack variable that will be correctly aligned.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-11-john@metanate.com
Requesting the HS clock from the PHY before we initialize it causes an
invalid signal to be sent out since the input clock is not yet
configured. The PHY databook suggests only asserting this signal when
performing HS transfers, so let's do that.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-10-john@metanate.com
Instead of always sending commands in LP mode, respect the
MIPI_DSI_MSG_USE_LPM flag to decide how to send each message. Also
request acks if MIPI_DSI_MSG_REQ_ACK is set.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-9-john@metanate.com
We want to check that both the GEN_CMD_EMPTY and GEN_PLD_W_EMPTY bits
are set so we can't just check "val & mask" because that will be true if
either bit is set.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-6-john@metanate.com
In a couple of places here we use "val" for the value that is about to
be written to a register but then reuse the same variable for the value
of a status register before we get around to writing it. Rename the
value to be written to so that we write the value we intend to and not
what we have just read from the status register.
Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-5-john@metanate.com
This is not needed since we can access the mode via the CRTC from the
enable hook. Also remove the "mode" field that is no longer used.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-4-john@metanate.com
This shows that we only use the mode from the enable function and
prepares us to remove the "mode" field and the mode_set hook in the next
commit.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-3-john@metanate.com
With atomic modesetting the hardware will be powered off when the
mode_set function is called. We should configure the hardware in the
enable function, which is the atomic version of "commit" so let's use
the enable hook rather than commit while we're at it.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-2-john@metanate.com
Backmerge the main pull request to sync up with all the newly landed
drivers. Otherwise we'll have chaos even before 4.12 started in
earnest.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Rockchip DRM used the arm special API, arm_iommu_*(), to attach
iommu for ARM32 SoCs. This patch convert to common iommu API
so it would support ARM64 like RK3399.
Since previous patch added support for direct IOMMU address space
management, there is no need to use DMA API anymore and this patch wires
things to use the new method.
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
The API is not suitable for subsystems consisting of multiple devices
and requires severe hacks to use it. To mitigate this, this patch
implements allocation and address space management locally by using
helpers provided by DRM framework, like other DRM drivers do, e.g.
Tegra.
This patch should not introduce any functional changes until the driver
is made to attach subdevices into an IOMMU domain with the generic IOMMU
API, which will happen in following patch. Based heavily on GEM
implementation of Tegra DRM driver.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: rjan Eide <orjan.eide@arm.com>
The drm_mode_config helper private field points to a structure of
function pointers that don't need to be modified at runtime. Make it
const.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Acked-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170102091613.6310-1-laurent.pinchart@ideasonboard.com
Core code already makes drm_driver.get_vblank_counter hook optional by
letting drm_vblank_no_hw_counter be the default implementation for the
function hook. So the drm_vblank_no_hw_counter assignment in the driver
code becomes redundant and can be removed now.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1486458995-31018-3-git-send-email-shawnguo@kernel.org
Noticed that everyone duplicates the same logic here and we could safe
a few lines per driver. Yay for lots of drivers to make such tiny
refactors worth-while!
v2: Forgot to git add everything :(
v3: Actually remove release_fbi (Sean, Emil, Chris) ...
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207161603.17611-1-daniel.vetter@ffwll.ch
fix warning:
drivers/gpu/drm/rockchip/cdn-dp-reg.c:632:24: warning:
'val[1]' may be used uninitialized in this function [-Wmaybe-uninitialized]
msa_misc = 2 * val[0] + 32 * val[1] +
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
rockchip CDN-DP support.
* 'drm-rockchip-next-2017-02-05' of https://github.com/markyzq/kernel-drm-rockchip:
drm/rockchip: cdn-dp: don't configure hardware in mode_set
drm/rockchip: cdn-dp: retry to check sink count
drm/rockchip: cdn-dp: Move mutex_init to probe
drm/rockchip: cdn-dp: do not use drm_helper_hpd_irq_event
drm/rockchip: cdn-dp: Do not run worker while suspended
drm/rockchip: cdn-dp: Load firmware if no monitor connected
drm/rockchip: cdn-dp: add cdn DP support for rk3399
drm/rockchip: return ERR_PTR instead of NULL
drm/rockchip: vop: make vop register setting take effect
With atomic modesetting the hardware will be powered off when the
mode_set function is called. We should configure the hardware in the
enable function.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Sometimes the Dock is disconnected, but cdn_dp_encoder_disable is not
triggered by DRM. For example, unplug the Dock in console mode, and
re-plug it again, the cdn_dp_event_work will try to get the sink count
of Dock, since the DP is still active. But the Dock has been powered
down, it need re-power on, and wait for a while until it is ready to
DPCD communication.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
We're trying to lock mutex when cdn-dp shutdown, so we need to make
sure the mutex is inited in cdn-dp's probe.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
The cdn_dp_pd_event_work is using drm_helper_hpd_irq_event to update the
connector status, this function is used to update all connectors of
drm_device. Therefore, the detect of other connector will be call, when
cdn_dp_pd_event_work is triggered, every time. It is not necessary, and
it may cause system crash. replace drm_helper_hpd_irq_event with
drm_kms_helper_hotplug_event, only update cdn-dp status.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
If the driver is in suspended mode, the dp block may be disabled, and
chip registers may not be accessible. Yet, the worker may be triggered
in this situation by an extcon event. If that happens, the following crash
will be seen.
cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work] *ERROR* Enable dp failed -19
cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work] Connected, not enabled. Enabling cdn
Bad mode in Error handler detected, code 0xbf000002 -- SError
CPU: 1 PID: 10357 Comm: kworker/1:2 Not tainted 4.4.21-05903-ge0514ea #1
Hardware name: Google Kevin (DT)
Workqueue: events cdn_dp_pd_event_work
task: ffffffc0cda67080 ti: ffffffc0b9b80000 task.ti: ffffffc0b9b80000
PC is at cdn_dp_clock_reset+0x30/0xa8
LR is at cdn_dp_enable+0x1e0/0x69c
...
Call trace:
[<ffffffc0005a7e24>] cdn_dp_pd_event_work+0x58/0x3f4
[<ffffffc0002397f0>] process_one_work+0x240/0x424
[<ffffffc00023a28c>] worker_thread+0x2fc/0x424
[<ffffffc00023f5fc>] kthread+0x10c/0x114
[<ffffffc000203dd0>] ret_from_fork+0x10/0x40
Problem is two-fold: The worker should not run while suspended, and the
suspend function should not call cdn_dp_disable() while the worker is
running.
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
If no monitor is connected, suspend/resume cycles result in firmware
load errors because the driver attempts to load the firmware while
the system is in suspend state. This results in a kernel warning and
traceback.
Loading the firmware during boot fixes the problem. Note that we can not
just call schedule_work conditionally in cdn_dp_pd_event() if the insertion
status changed. The problem would still be seen if a monitor is connected
for the first time during suspend.
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Add support for cdn DP controller which is embedded in the rk3399
SoCs. The DP is compliant with DisplayPort Specification,
Version 1.3, This IP is compatible with the rockchip type-c PHY IP.
There is a uCPU in DP controller, it need a firmware to work,
please put the firmware file to /lib/firmware/rockchip/dptx.bin. The
uCPU in charge of aux communication and link training, the host use
mailbox to communicate with the ucpu.
The dclk pin_pol of vop must not be invert for DP.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
[seanpaul fixed up some races between the worker and modeset]
[seanpaul squashed ~15 commits from chromium.org gerrit]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
[groeck fixed compilation errors when building as module]
Signed-off-by: Guenter Roeck <groeck@chromium.org>
rockchip_drm_framebuffer_init is only used in one case, in
rockchip_drm_fbdev.c, where its return value is tested using IS_ERR. To
enable propagating the reason for the error, change the definition so that
it returns an ERR_PTR value.
Problem found with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
The setting of vop registers need a reg_done writing to take effect.
In vop_enable the vop return to work by by restoring registers, but the
registers do not take effect immediately, it should a vop_cfg_done
after it. The same thing is needed by windows_disabled in
vop_crtc_disable.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Instead of receiving the num_crts as a parameter, we can read it
directly from the mode_config structure. I audited the drivers that
invoke this helper and I believe all of them initialize the mode_config
struct accordingly, prior to calling the fb_helper.
I used the following coccinelle hack to make this transformation, except
for the function headers and comment updates. The first and second
rules are split because I couldn't find a way to remove the unused
temporary variables at the same time I removed the parameter.
// <smpl>
@r@
expression A,B,D,E;
identifier C;
@@
(
- drm_fb_helper_init(A,B,C,D)
+ drm_fb_helper_init(A,B,D)
|
- drm_fbdev_cma_init_with_funcs(A,B,C,D,E)
+ drm_fbdev_cma_init_with_funcs(A,B,D,E)
|
- drm_fbdev_cma_init(A,B,C,D)
+ drm_fbdev_cma_init(A,B,D)
)
@@
expression A,B,C,D,E;
@@
(
- drm_fb_helper_init(A,B,C,D)
+ drm_fb_helper_init(A,B,D)
|
- drm_fbdev_cma_init_with_funcs(A,B,C,D,E)
+ drm_fbdev_cma_init_with_funcs(A,B,D,E)
|
- drm_fbdev_cma_init(A,B,C,D)
+ drm_fbdev_cma_init(A,B,D)
)
@@
identifier r.C;
type T;
expression V;
@@
- T C;
<...
when != C
- C = V;
...>
// </smpl>
Changes since v1:
- Rebased on top of the tip of drm-misc-next.
- Remove mention to sti since a proper fix got merged.
Suggested-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170202162640.27261-1-krisman@collabora.co.uk
There's no need to duplicate identical code in multiple drivers (two at
the moment, one more to come soon). Move it to the dw-hdmi core where it
can be shared. If resource allocation ever becomes device-specific later
we'll always have the option of splitting it out again.
While it at pass the platform device to the bind function to avoid
having to cast struct device to struct platform_device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-8-laurent.pinchart+renesas@ideasonboard.com
The master argument isn't used. The data argument, a void pointer, is
used by the bind function only where it's cast to a drm_device pointer,
which can easily be obtained from the encoder argument instead. Remove
them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-3-laurent.pinchart+renesas@ideasonboard.com
Many drivers (21 to be exact) create connectors that are always
connected (for instance to an LVDS or DSI panel). Instead of forcing
them to implement a dummy .detect() handler, make the callback optional
and consider the connector as always connected in that case.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[seanpaul fixed small conflict in rcar-du/rcar_du_lvdscon.c]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Convert DT component matching to use component_match_add_release().
Acked-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/E1bwo6l-0005Io-Q1@rmk-PC.armlinux.org.uk
These GPU drivers only depend on the RESET_CONTROLLER config
option to fix build issues that existed when there weren't stub
reset APIs for reset controller consumers. Given that these
drivers aren't providing any reset controllers themselves, they
don't actually depend on the API to build (just to function) so
they don't need to depend on it. Remove the dependency to fix
recursive build errors like the following:
drivers/usb/Kconfig:39:error: recursive dependency detected!
drivers/usb/Kconfig:39: symbol USB is selected by MOUSE_APPLETOUCH
drivers/input/mouse/Kconfig:187: symbol MOUSE_APPLETOUCH depends on INPUT
drivers/input/Kconfig:8: symbol INPUT is selected by VT
drivers/tty/Kconfig:12: symbol VT is selected by FB_STI
drivers/video/fbdev/Kconfig:674: symbol FB_STI depends on FB
drivers/video/fbdev/Kconfig:5: symbol FB is selected by DRM_KMS_FB_HELPER
drivers/gpu/drm/Kconfig:42: symbol DRM_KMS_FB_HELPER is selected by DRM_KMS_CMA_HELPER
drivers/gpu/drm/Kconfig:98: symbol DRM_KMS_CMA_HELPER is selected by DRM_IMX
drivers/gpu/drm/imx/Kconfig:1: symbol DRM_IMX depends on IMX_IPUV3_CORE
drivers/gpu/ipu-v3/Kconfig:1: symbol IMX_IPUV3_CORE depends on RESET_CONTROLLER
drivers/reset/Kconfig:4: symbol RESET_CONTROLLER is selected by USB_CHIPIDEA
drivers/usb/chipidea/Kconfig:1: symbol USB_CHIPIDEA depends on USB_EHCI_HCD
drivers/usb/host/Kconfig:84: symbol USB_EHCI_HCD depends on USB
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: <dri-devel@lists.freedesktop.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Mark Yao <mark.yao@rock-chips.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: robdclark@gmail.com
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161018205719.20575-1-stephen.boyd@linaro.org
There's no point in enabling PSR when the panel doesn't support it.
This also avoids a problem when PSR gets enabled when a CRTC is being
disabled, because sometimes in that situation the DSP_HOLD_VALID_INTR
interrupt on which we wait will never arrive. This was observed on
RK3288 with a panel without PSR (veyron-jaq Chromebook).
It's very easy to reproduce by running the kms_rmfb test in IGT a few
times.
Cc: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1474639600-30090-2-git-send-email-tomeu.vizoso@collabora.com
We get 2 warnings when building kernel with W=1:
drivers/gpu/drm/rockchip/rockchip_drm_drv.c:309:6: warning: no previous prototype for 'rockchip_drm_fb_suspend' [-Wmissing-prototypes]
drivers/gpu/drm/rockchip/rockchip_drm_drv.c:318:6: warning: no previous prototype for 'rockchip_drm_fb_resume' [-Wmissing-prototypes]
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
So this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1474789388-3284-1-git-send-email-baoyou.xie@linaro.org
We get 2 warnings when building kernel with W=1:
drivers/gpu/drm/rockchip/rockchip_drm_fbdev.c:130:5: warning: no previous prototype for 'rockchip_drm_fbdev_init' [-Wmissing-prototypes]
drivers/gpu/drm/rockchip/rockchip_drm_fbdev.c:173:6: warning: no previous prototype for 'rockchip_drm_fbdev_fini' [-Wmissing-prototypes]
In fact, these functions are declared
in drivers/gpu/drm/rockchip/rockchip_drm_fbdev.h,
so this patch adds missing header dependencies.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1474789109-22010-1-git-send-email-baoyou.xie@linaro.org
I've included some improvements to PSR from myself, as well as a great
series from Tomasz to clean up and tighten up vblank/flip handling.
The last patch is one from Tomeu that has been floating around for a
while, and since rockchip is one of the beneficiaries, I figured this
would be a good place to pick it up.
* 'for-next' of ssh://people.freedesktop.org/~seanpaul/dogwood:
drm/rockchip: Balance irq refcount on failure
drm/rockchip: Kill vop_plane_state
drm/rockchip: Always signal event in next vblank after cfg_done
drm/rockchip: Do not enable vblank without event
drm/rockchip: Replace custom wait_for_vblanks with helper
drm/rockchip: Unreference framebuffers from flip work
drm/rockchip: Avoid race with vblank count increment
drm/rockchip: Get rid of some unnecessary code
drm/rockchip: Clear interrupt status bits before enabling
drm/rockchip: Fix up bug in psr state machine
drm/bridge: analogix_dp: Remove duplicated code
drm/rockchip: Reduce psr flush time to 100ms
drm/rockchip: Don't key off vblank for psr
There are many reasons other than ENOMEM that drm_dev_init() can
fail. Return ERR_PTR rather than NULL to be able to distinguish
these in the caller.
Signed-off-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20160921145919.13754-2-teg@jklm.no
If create_crtc fails in vop bind, ensure the irq refcount is zeroed
back out before exiting.
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
John Keeping