Previously PAXIC register was programmed before configuring PCFG
register. PCFG should be programmed with the address of the port
for which PAXIC should be configured for.
This was not happening before, so only one port PAXIC was written
correctly and the other port was having wrong value.
This patch moves the PXAIC register write after configuring PCFG,
doing so will correct the axi bus settings for sata port0 & port1.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds support for CCI in SATA controller if CCI is
enabled in design. This patch will add CCI settings for SATA
if "dma-coherent" dts property is added.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch updates the driver to make Rx Fifo water mark value
as a module parameter.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Since CEVA controller does not support Device Sleep capability,
we need to clear that feature by clearing the DEVSLP bit in word78
of IDENTIFY DEVICE data. This patch does the same.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch sets gen 3 mode as default mode in ahci_ceva driver.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
In SATA Speed negotiation happens with OOB(Out of Band) signals. These OOB
signal timing values are configured through vendor specific registers in the
SATA controller. These OOB timings depends on the generator and detector clock
frequency, which varies from board to board (ex: ep108 and zc1751 has different
clock frequencies).
To avoid maintaing these OOB settings in the driver, it is better to move these
settings to the device-tree node and read from the device-tree.
This patch does the same.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
In cases where a "drop through" comment was already in place, I replaced
it with a proper "fall through" comment, which is what GCC is expecting
to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The pointer ehi is being assigned to a value that is never read
and is redundant. Clean up the code and move the ehi declaration
and initialization to the code block where it is used. Cleans up
clang warning: Value stored to 'ehi' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Adds a pointer back to link
structure.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
Link: https://lkml.kernel.org/r/20171016215658.GA101965@beast
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
Link: https://lkml.kernel.org/r/20171005004842.GA23011@beast
This patch adds support for Cavium's fifth generation SATA controller.
It is an on-chip controller and complies with AHCI 1.3.1. As the
controller uses 64-bit addresses it cannot use the standard AHCI BAR5
and so uses BAR4.
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use the of_device_get_match_data() helper instead of open coding.
Note that the sata_rcar driver is used with DT only, so there's always a
valid match.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ahci_pci_reset_controller() calls ahci_reset_controller(), which may
fail, but ignores the result code and always returns success. This
may result in failures like below
ahci 0000:02:00.0: version 3.0
ahci 0000:02:00.0: enabling device (0000 -> 0003)
ahci 0000:02:00.0: SSS flag set, parallel bus scan disabled
ahci 0000:02:00.0: controller reset failed (0xffffffff)
ahci 0000:02:00.0: failed to stop engine (-5)
... repeated many times ...
ahci 0000:02:00.0: failed to stop engine (-5)
Unable to handle kernel paging request at virtual address ffff0000093f9018
...
PC is at ahci_stop_engine+0x5c/0xd8 [libahci]
LR is at ahci_deinit_port.constprop.12+0x1c/0xc0 [libahci]
...
[<ffff000000a17014>] ahci_stop_engine+0x5c/0xd8 [libahci]
[<ffff000000a196b4>] ahci_deinit_port.constprop.12+0x1c/0xc0 [libahci]
[<ffff000000a197d8>] ahci_init_controller+0x80/0x168 [libahci]
[<ffff000000a260f8>] ahci_pci_init_controller+0x60/0x68 [ahci]
[<ffff000000a26f94>] ahci_init_one+0x75c/0xd88 [ahci]
[<ffff000008430324>] local_pci_probe+0x3c/0xb8
[<ffff000008431728>] pci_device_probe+0x138/0x170
[<ffff000008585e54>] driver_probe_device+0x2dc/0x458
[<ffff0000085860e4>] __driver_attach+0x114/0x118
[<ffff000008583ca8>] bus_for_each_dev+0x60/0xa0
[<ffff000008585638>] driver_attach+0x20/0x28
[<ffff0000085850b0>] bus_add_driver+0x1f0/0x2a8
[<ffff000008586ae0>] driver_register+0x60/0xf8
[<ffff00000842f9b4>] __pci_register_driver+0x3c/0x48
[<ffff000000a3001c>] ahci_pci_driver_init+0x1c/0x1000 [ahci]
[<ffff000008083918>] do_one_initcall+0x38/0x120
where an obvious hardware level failure results in an unnecessary 15 second
delay and a subsequent crash.
So record the result code of ahci_reset_controller() and relay it, rather
than ignoring it.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Make this const as it is only stored in the const field of a device
structure. Make the declaration in header const too.
Structure found using Coccinelle and changes done by hand.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Don't populate const arrayis on the stack, instead make them static.
Makes the object code smaller by over 260 bytes:
Before:
text data bss dec hex filename
64864 5948 4128 74940 124bc drivers/ata/libata-scsi.o
After:
text data bss dec hex filename
64183 6364 4128 74675 123b3 drivers/ata/libata-scsi.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fujitsu-Siemens Lifebook S6120 misdetects the cable type for some
drives. The problematic one in this case is an mSATA SSD hooked up via a
mSATA->PATA bridge. With regular hard disks the detection seems to work
correctly.
Strangely an older Lifebook model (S6020) detects the cable as 80c
with the mSATA SSD, even if using the exact same flex cable.
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
pio is initialized and the data is never read, instead it is almost
immediately being updated to a new value. Fix this by removing the
initialization.
Detected by scan-build:
"warning: Value stored to 'pio' during its initialization is never read"
Fixes: 669a5db411 ("[libata] Add a bunch of PATA drivers")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
As described by Matthew Garret quite a while back:
https://mjg59.dreamwidth.org/34868.html
Intel CPUs starting with the Haswell generation need SATA links to power
down for the "package" part of the CPU to reach low power-states like
PC7 / P8 which bring a significant power-saving with them.
The default max_performance lpm policy does not allow for these high
PC states, both the medium_power and min_power policies do allow this.
The min_power policy saves significantly more power, but there are some
reports of some disks / SSDs not liking min_power leading to system
crashes and in some cases even data corruption has been reported.
Matthew has found a document documenting the default settings of
Intel's IRST Windows driver with which most laptops ship:
https://www-ssl.intel.com/content/dam/doc/reference-guide/sata-devices-implementation-recommendations.pdf
Matthew wrote a patch changing med_power to match those defaults, but
that never got anywhere as some people where reporting issues with the
patch-set that patch was a part of.
This commit is another attempt to make the default IRST driver settings
available under Linux, but instead of changing medium_power and
potentially introducing regressions, this commit adds a new
med_power_with_dipm setting which is identical to the existing
medium_power accept that it enables dipm on top, which makes it match
the Windows IRST driver settings, which should hopefully be safe to
use on most devices.
The med_power_with_dipm setting is close to min_power, except that:
a) It does not use host-initiated slumber mode (ASP not set),
but it does allow device-initiated slumber
b) It does not enable DevSlp mode
On my T440s test laptop I get the following power savings when idle:
medium_power 0.9W
med_power_with_dipm 1.2W
min_power 1.2W
Suggested-by: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
gcc-7 warns about the result of a constant multiplication used as
a boolean:
drivers/ata/libata-core.c: In function 'ata_timing_quantize':
drivers/ata/libata-core.c:3164:30: warning: '*' in boolean context, suggest '&&' instead [-Wint-in-bool-context]
This slightly rearranges the macro to simplify the code and avoid
the warning at the same time.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
"Except for the ahci fix that fixes a boot issue, nothing major in this
pull request. Some new platform controller support and device specific
changes"
* 'for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: zpodd: make arrays cdb static, reduces object code size
ahci: don't use MSI for devices with the silly Intel NVMe remapping scheme
dt-bindings: ata: add DT bindings for MediaTek SATA controller
ata: mediatek: add support for MediaTek SATA controller
pata_octeon_cf: use of_property_read_{bool|u32}()
cs5536: add support for IDE controller variant
ata: sata_gemini: Introduce explicit IDE pin control
ata: sata_gemini: Retire custom pin control
ata: ahci_platform: Add shutdown handler
ata: sata_gemini: explicitly request exclusive reset control
ata: Drop unnecessary static
ata: Convert to using %pOF instead of full_name
Don't populate the arrays cdb on the stack, instead make them static.
Makes the object code smaller by 230 bytes:
Before:
text data bss dec hex filename
3797 240 0 4037 fc5 drivers/ata/libata-zpodd.o
After:
text data bss dec hex filename
3407 400 0 3807 edf drivers/ata/libata-zpodd.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Intel AHCI controllers that also hide NVMe devices in their bar
can't use MSI interrupts, so disable them.
Reported-by: John Loy <john.robert.loy@gmail.com>
Tested-by: John Loy <john.robert.loy@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes: d684a90d38 ("ahci: per-port msix support")
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull RCU updates from Ingo Molnad:
"The main RCU related changes in this cycle were:
- Removal of spin_unlock_wait()
- SRCU updates
- RCU torture-test updates
- RCU Documentation updates
- Extend the sys_membarrier() ABI with the MEMBARRIER_CMD_PRIVATE_EXPEDITED variant
- Miscellaneous RCU fixes
- CPU-hotplug fixes"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (63 commits)
arch: Remove spin_unlock_wait() arch-specific definitions
locking: Remove spin_unlock_wait() generic definitions
drivers/ata: Replace spin_unlock_wait() with lock/unlock pair
ipc: Replace spin_unlock_wait() with lock/unlock pair
exit: Replace spin_unlock_wait() with lock/unlock pair
completion: Replace spin_unlock_wait() with lock/unlock pair
doc: Set down RCU's scheduling-clock-interrupt needs
doc: No longer allowed to use rcu_dereference on non-pointers
doc: Add RCU files to docbook-generation files
doc: Update memory-barriers.txt for read-to-write dependencies
doc: Update RCU documentation
membarrier: Provide expedited private command
rcu: Remove exports from rcu_idle_exit() and rcu_idle_enter()
rcu: Add warning to rcu_idle_enter() for irqs enabled
rcu: Make rcu_idle_enter() rely on callers disabling irqs
rcu: Add assertions verifying blocked-tasks list
rcu/tracing: Set disable_rcu_irq_enter on rcu_eqs_exit()
rcu: Add TPS() protection for _rcu_barrier_trace strings
rcu: Use idle versions of swait to make idle-hack clear
swait: Add idle variants which don't contribute to load average
...
This reverts commit 35f0b6a779.
We now conditionalize issuing of READ LOG PAGE on the TRUSTED
COMPUTING SUPPORTED bit in the identity data and this shouldn't be
necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
ATA-8 and later mirrors the TRUSTED COMPUTING SUPPORTED bit in word 48 of
the IDENTIFY DEVICE data. Check this before issuing a READ LOG PAGE
command to avoid issues with buggy devices. The only downside is that
we can't support Security Send / Receive for a device with an older
revision due to the conflicting use of this field in earlier
specifications.
tj: The reason we need this is because some devices which don't
support READ LOG PAGE lock up after getting issued that command.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This adds support the AHCI-compliant Serial ATA controller present
on MediaTek SoCs.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
The Octeon CF driver basically open-codes of_property_read_{bool|u32}()
using of_{find|get}_property() calls in its probe() method. Using the
modern DT APIs saves 2 LoCs and 16 bytes of object code (MIPS gcc 3.4.3).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Ido reported that reading the log page on his systems fails,
so quirk it as it won't support ZBC or security protocols.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There is no agreed-upon definition of spin_unlock_wait()'s semantics,
and it appears that all callers could do just as well with a lock/unlock
pair. This commit therefore eliminates the spin_unlock_wait() call and
associated else-clause and hoists the then-clause's lock and unlock out of
the "if" statement. This should be safe from a performance perspective
because according to Tejun there should be few if any drivers that don't
set their own error handler.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: <linux-ide@vger.kernel.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrea Parri <parri.andrea@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
'rc' is known to be 0 at this point.
If 'platform_get_resource()' or 'devm_ioremap()' fail, return -ENOMEM
instead of 0 which means success.
tj: Changed error code from -ENOMEM to -ENODEV for get_resource
failure as suggested by Sergei.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Several legacy devices such as Geode-based Cisco ASA appliances
and DB800 development board do possess CS5536 IDE controller
with different PCI id than existing one. Using pata_generic is
not always feasible as at least DB800 requires MSR quirk from
pata_cs5536 to be used with vendor firmware.
Signed-off-by: Andrey Korolyov <andrey@xdel.ru>
CC: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
The IDE pins are managed by the pin controller, if we want to
use these, we need to ask the pin controller to explicitly enable
them as by default, these pins are used for other business and
most users just rely on the SATA bridge.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
I added a proper pin control driver for the Gemini SoC, so retire
this custom code and rely on the pin controller to set up the pads.
The "IOMUX" which is routing signals between the ATA and SATA
bridge inside of the chip is not about pin control and remains in
place.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
The newly introduced ahci_platform_shutdown() method is called during
system shutdown to disable host controller DMA and interrupts in order
to avoid potentially corrupting or otherwise interfering with a new
kernel being started with kexec.
Signed-off-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: linux-ide@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Drop static on a local variable, when the variable is initialized before
any possible use. Thus, the static has no benefit.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
The kerneldoc comments for a couple of functions in drivers/ata/libata-eh.c
had fallen behind the current implementation, resulting in these doc build
warnings:
./drivers/ata/libata-eh.c:1449: warning: No description found for parameter 'link'
./drivers/ata/libata-eh.c:1449: warning: Excess function parameter 'ap' description in 'ata_eh_done'
./drivers/ata/libata-eh.c:1590: warning: No description found for parameter 'qc'
./drivers/ata/libata-eh.c:1590: warning: Excess function parameter 'dev' description in 'ata_eh_request_sense'
Update the comments and make the warnings go away.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
My static checker complains that "devno" can be negative, meaning that
we read before the start of the loop. I've looked at the code, and I
think the warning is right. This come from /proc so it's root only or
it would be quite a quite a serious bug. The call tree looks like this:
proc_scsi_write() <- gets id and channel from simple_strtoul()
-> scsi_add_single_device() <- calls shost->transportt->user_scan()
-> ata_scsi_user_scan()
-> ata_find_dev()
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org # all versions at this point
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Add fallback compatibility string for R-Car Gen 2 and 3.
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, e.g. Gen 1 and 2. But beyond that its not clear what the relationship
between IP blocks might be. For example, I believe that r8a7790 is older
than r8a7791 but that doesn't imply that the latter is a descendant of the
former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme being adopted for
drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
The warning message "READ LOG DMA EXT failed, trying unqueued" in
ata_read_log_page() as well as the macro name ATA_HORKAGE_NO_NCQ_LOG
are confusing: the command READ LOG DMA EXT is not an queued NCQ command
unless it is encapsulated in a RECEIVE FPDMA QUEUED command.
From ACS-4 READ LOG DMA EXT description:
"The device processes the READ LOG DMA EXT command in the NCQ feature
set environment (see 4.13.6) if the READ LOG DMA EXT command is
encapsulated in a RECEIVE FPDMA QUEUED command (see 7.30) with the
inputs encapsulated as shown in 7.23.6."
To avoid confusion, fix the warning messsage to mention switching to PIO and
not "unqueued" and rename the macro ATA_HORKAGE_NO_NCQ_LOG to
ATA_HORKAGE_NO_DMA_LOG.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
We cannot build the new ftide010 code without also building the faraday
sata bridge driver:
drivers/ata/pata_ftide010.o: In function `pata_ftide010_probe':
pata_ftide010.c:(.text+0x2b8): undefined reference to `gemini_sata_bridge_get'
pata_ftide010.c:(.text+0x32c): undefined reference to `gemini_sata_get_muxmode'
pata_ftide010.c:(.text+0x358): undefined reference to `gemini_sata_bridge_enabled'
drivers/ata/pata_ftide010.o: In function `pata_ftide010_gemini_port_stop':
pata_ftide010.c:(.text+0x520): undefined reference to `gemini_sata_stop_bridge'
drivers/ata/pata_ftide010.o: In function `pata_ftide010_gemini_port_start':
pata_ftide010.c:(.text+0x5bc): undefined reference to `gemini_sata_start_bridge'
This adjusts the Kconfig dependencies accordingly.
Fixes: be4e456ed3 ("ata: Add driver for Faraday Technology FTIDE010")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
- Christoph added support for TCG OPAL self encrypting disks
- Minwoo added support for ATA PASS-THROUGH(32)
- Linus Walleij removed spurious drvdata assignments in some drivers
- Support for a few new device and other fixes
* 'for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (33 commits)
sd: add support for TCG OPAL self encrypting disks
libata: fix build warning from unused goto label
libata: Support for an ATA PASS-THROUGH(32) command.
ahci: Add Device ID for ASMedia 1061R and 1062R
sata_via: Enable optional hotplug on VT6420
ata: ahci_brcm: Avoid writing to read-only registers
libata: Add the AHCI_HFLAG_NO_WRITE_TO_RO flag
libata: Add the AHCI_HFLAG_YES_ALPM flag
ata: ftide010: fix resource printing
libata: make the function name in comment match the actual function
ata: sata_rcar: make of_device_ids const.
ata: pata_octeon_cf: make of_device_ids const.
libata: Convert bare printks to pr_cont
libahci: wrong comments in ahci_do_softreset()
ata: declare ata_port_info structures as const
ata: Add driver for Faraday Technology FTIDE010
ata: Add DT bindings for the Gemini SATA bridge
ata: Add DT bindings for Faraday Technology FTIDE010
libata: implement SECURITY PROTOCOL IN/OUT
libata: factor out a ata_identify_page_supported helper
...
- Rework suspend-to-idle to allow it to take wakeup events signaled
by the EC into account on ACPI-based platforms in order to properly
support power button wakeup from suspend-to-idle on recent Dell
laptops (Rafael Wysocki).
That includes the core suspend-to-idle code rework, support for
the Low Power S0 _DSM interface, and support for the ACPI INT0002
Virtual GPIO device from Hans de Goede (required for USB keyboard
wakeup from suspend-to-idle to work on some machines).
- Stop trying to export the current CPU frequency via /proc/cpuinfo
on x86 as that is inaccurate and confusing (Len Brown).
- Rework the way in which the current CPU frequency is exported by
the kernel (over the cpufreq sysfs interface) on x86 systems with
the APERF and MPERF registers by always using values read from
these registers, when available, to compute the current frequency
regardless of which cpufreq driver is in use (Len Brown).
- Rework the PCI/ACPI device wakeup infrastructure to remove the
questionable and artificial distinction between "devices that
can wake up the system from sleep states" and "devices that can
generate wakeup signals in the working state" from it, which
allows the code to be simplified quite a bit (Rafael Wysocki).
- Fix the wakeup IRQ framework by making it use SRCU instead of
RCU which doesn't allow sleeping in the read-side critical
sections, but which in turn is expected to be allowed by the
IRQ bus locking infrastructure (Thomas Gleixner).
- Modify some computations in the intel_pstate driver to avoid
rounding errors resulting from them (Srinivas Pandruvada).
- Reduce the overhead of the intel_pstate driver in the HWP
(hardware-managed P-states) mode and when the "performance"
P-state selection algorithm is in use by making it avoid
registering scheduler callbacks in those cases (Len Brown).
- Rework the energy_performance_preference sysfs knob in
intel_pstate by changing the values that correspond to
different symbolic hint names used by it (Len Brown).
- Make it possible to use more than one cpuidle driver at the same
time on ARM (Daniel Lezcano).
- Make it possible to prevent the cpuidle menu governor from using
the 0 state by disabling it via sysfs (Nicholas Piggin).
- Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1
on AMD systems (Yazen Ghannam).
- Make the CPPC cpufreq driver take the lowest nonlinear performance
information into account (Prashanth Prakash).
- Add support for hi3660 to the cpufreq-dt driver, fix the
imx6q driver and clean up the sfi, exynos5440 and intel_pstate
drivers (Colin Ian King, Krzysztof Kozlowski, Octavian Purdila,
Rafael Wysocki, Tao Wang).
- Fix a few minor issues in the generic power domains (genpd)
framework and clean it up somewhat (Krzysztof Kozlowski,
Mikko Perttunen, Viresh Kumar).
- Fix a couple of minor issues in the operating performance points
(OPP) framework and clean it up somewhat (Viresh Kumar).
- Fix a CONFIG dependency in the hibernation core and clean it up
slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
- Add rk3228 support to the rockchip-io adaptive voltage scaling
(AVS) driver (David Wu).
- Fix an incorrect bit shift operation in the RAPL power capping
driver (Adam Lessnau).
- Add support for the EPP field in the HWP (hardware managed
P-states) control register, HWP.EPP, to the x86_energy_perf_policy
tool and update msr-index.h with HWP.EPP values (Len Brown).
- Fix some minor issues in the turbostat tool (Len Brown).
- Add support for AMD family 0x17 CPUs to the cpupower tool and fix
a minor issue in it (Sherry Hurwitz).
- Assorted cleanups, mostly related to the constification of some
data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
Kozlowski).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Wsph
-----END PGP SIGNATURE-----
Merge tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The big ticket items here are the rework of suspend-to-idle in order
to add proper support for power button wakeup from it on recent Dell
laptops and the rework of interfaces exporting the current CPU
frequency on x86.
In addition to that, support for a few new pieces of hardware is
added, the PCI/ACPI device wakeup infrastructure is simplified
significantly and the wakeup IRQ framework is fixed to unbreak the IRQ
bus locking infrastructure.
Also, there are some functional improvements for intel_pstate, tools
updates and small fixes and cleanups all over.
Specifics:
- Rework suspend-to-idle to allow it to take wakeup events signaled
by the EC into account on ACPI-based platforms in order to properly
support power button wakeup from suspend-to-idle on recent Dell
laptops (Rafael Wysocki).
That includes the core suspend-to-idle code rework, support for the
Low Power S0 _DSM interface, and support for the ACPI INT0002
Virtual GPIO device from Hans de Goede (required for USB keyboard
wakeup from suspend-to-idle to work on some machines).
- Stop trying to export the current CPU frequency via /proc/cpuinfo
on x86 as that is inaccurate and confusing (Len Brown).
- Rework the way in which the current CPU frequency is exported by
the kernel (over the cpufreq sysfs interface) on x86 systems with
the APERF and MPERF registers by always using values read from
these registers, when available, to compute the current frequency
regardless of which cpufreq driver is in use (Len Brown).
- Rework the PCI/ACPI device wakeup infrastructure to remove the
questionable and artificial distinction between "devices that can
wake up the system from sleep states" and "devices that can
generate wakeup signals in the working state" from it, which allows
the code to be simplified quite a bit (Rafael Wysocki).
- Fix the wakeup IRQ framework by making it use SRCU instead of RCU
which doesn't allow sleeping in the read-side critical sections,
but which in turn is expected to be allowed by the IRQ bus locking
infrastructure (Thomas Gleixner).
- Modify some computations in the intel_pstate driver to avoid
rounding errors resulting from them (Srinivas Pandruvada).
- Reduce the overhead of the intel_pstate driver in the HWP
(hardware-managed P-states) mode and when the "performance" P-state
selection algorithm is in use by making it avoid registering
scheduler callbacks in those cases (Len Brown).
- Rework the energy_performance_preference sysfs knob in intel_pstate
by changing the values that correspond to different symbolic hint
names used by it (Len Brown).
- Make it possible to use more than one cpuidle driver at the same
time on ARM (Daniel Lezcano).
- Make it possible to prevent the cpuidle menu governor from using
the 0 state by disabling it via sysfs (Nicholas Piggin).
- Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1 on
AMD systems (Yazen Ghannam).
- Make the CPPC cpufreq driver take the lowest nonlinear performance
information into account (Prashanth Prakash).
- Add support for hi3660 to the cpufreq-dt driver, fix the imx6q
driver and clean up the sfi, exynos5440 and intel_pstate drivers
(Colin Ian King, Krzysztof Kozlowski, Octavian Purdila, Rafael
Wysocki, Tao Wang).
- Fix a few minor issues in the generic power domains (genpd)
framework and clean it up somewhat (Krzysztof Kozlowski, Mikko
Perttunen, Viresh Kumar).
- Fix a couple of minor issues in the operating performance points
(OPP) framework and clean it up somewhat (Viresh Kumar).
- Fix a CONFIG dependency in the hibernation core and clean it up
slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
- Add rk3228 support to the rockchip-io adaptive voltage scaling
(AVS) driver (David Wu).
- Fix an incorrect bit shift operation in the RAPL power capping
driver (Adam Lessnau).
- Add support for the EPP field in the HWP (hardware managed
P-states) control register, HWP.EPP, to the x86_energy_perf_policy
tool and update msr-index.h with HWP.EPP values (Len Brown).
- Fix some minor issues in the turbostat tool (Len Brown).
- Add support for AMD family 0x17 CPUs to the cpupower tool and fix a
minor issue in it (Sherry Hurwitz).
- Assorted cleanups, mostly related to the constification of some
data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
Kozlowski)"
* tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (69 commits)
cpufreq: Update scaling_cur_freq documentation
cpufreq: intel_pstate: Clean up after performance governor changes
PM: hibernate: constify attribute_group structures.
cpuidle: menu: allow state 0 to be disabled
intel_idle: Use more common logging style
PM / Domains: Fix missing default_power_down_ok comment
PM / Domains: Fix unsafe iteration over modified list of domains
PM / Domains: Fix unsafe iteration over modified list of domain providers
PM / Domains: Fix unsafe iteration over modified list of device links
PM / Domains: Handle safely genpd_syscore_switch() call on non-genpd device
PM / Domains: Call driver's noirq callbacks
PM / core: Drop run_wake flag from struct dev_pm_info
PCI / PM: Simplify device wakeup settings code
PCI / PM: Drop pme_interrupt flag from struct pci_dev
ACPI / PM: Consolidate device wakeup settings code
ACPI / PM: Drop run_wake from struct acpi_device_wakeup_flags
PM / QoS: constify *_attribute_group.
PM / AVS: rockchip-io: add io selectors and supplies for rk3228
powercap/RAPL: prevent overridding bits outside of the mask
PM / sysfs: Constify attribute groups
...
around. Highlights include:
- Conversion of a bunch of security documentation into RST
- The conversion of the remaining DocBook templates by The Amazing
Mauro Machine. We can now drop the entire DocBook build chain.
- The usual collection of fixes and minor updates.
-----BEGIN PGP SIGNATURE-----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=cVjZ
-----END PGP SIGNATURE-----
Merge tag 'docs-4.13' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"There has been a fair amount of activity in the docs tree this time
around. Highlights include:
- Conversion of a bunch of security documentation into RST
- The conversion of the remaining DocBook templates by The Amazing
Mauro Machine. We can now drop the entire DocBook build chain.
- The usual collection of fixes and minor updates"
* tag 'docs-4.13' of git://git.lwn.net/linux: (90 commits)
scripts/kernel-doc: handle DECLARE_HASHTABLE
Documentation: atomic_ops.txt is core-api/atomic_ops.rst
Docs: clean up some DocBook loose ends
Make the main documentation title less Geocities
Docs: Use kernel-figure in vidioc-g-selection.rst
Docs: fix table problems in ras.rst
Docs: Fix breakage with Sphinx 1.5 and upper
Docs: Include the Latex "ifthen" package
doc/kokr/howto: Only send regression fixes after -rc1
docs-rst: fix broken links to dynamic-debug-howto in kernel-parameters
doc: Document suitability of IBM Verse for kernel development
Doc: fix a markup error in coding-style.rst
docs: driver-api: i2c: remove some outdated information
Documentation: DMA API: fix a typo in a function name
Docs: Insert missing space to separate link from text
doc/ko_KR/memory-barriers: Update control-dependencies example
Documentation, kbuild: fix typo "minimun" -> "minimum"
docs: Fix some formatting issues in request-key.rst
doc: ReSTify keys-trusted-encrypted.txt
doc: ReSTify keys-request-key.txt
...
Just wire up the generic TCG OPAL infrastructure to the SCSI disk driver
and the Security In/Out commands.
Note that I don't know of any actual SCSI disks that do support TCG OPAL,
but this is required to support ATA disks through libata.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
b1ffbf854e ("libata: Support for an ATA PASS-THROUGH(32) command.")
introduced an unused goto label. Remove it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently, there are two separate ways of handling device wakeup
settings in the ACPI core, depending on whether this is runtime
wakeup or system wakeup (from sleep states). However, after the
previous commit eliminating the run_wake ACPI device wakeup flag,
there is no difference between the two any more at the ACPI level,
so they can be combined.
For this reason, introduce acpi_pm_set_device_wakeup() to replace both
acpi_pm_device_run_wake() and acpi_pm_device_sleep_wake() and make it
check the ACPI device object's wakeup.valid flag to determine whether
or not the device can be set up to generate wakeup signals.
Also notice that zpodd_enable/disable_run_wake() only call
device_set_run_wake() because acpi_pm_device_run_wake() called
device_run_wake(), which is not done by acpi_pm_set_device_wakeup(),
so drop the now redundant device_set_run_wake() calls from there.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
SAT-4(SCSI/ATA Translation) supports for an ata pass-thru(32).
This patch will allow to translate an ata pass-thru(32) SCSI cmd
to an ATA cmd.
Signed-off-by: Minwoo Im <dn3108@gmail.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
VT6420 seems to have the same hotplug capability as VT6421.
However, enabling hotplug needs to expose SCR registers which can cause
problems. It works for me but might break elsewhere. So add a module
parameter vt6420_hotplug to enable this feature.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
This commit makes use of the AHCI_HFLAG_YES_ALPM flag to prevent
the driver from writing to the read-only Host Capability register.
It also sets the AHCI_HFLAG_NO_WRITE_TO_RO flag to prevent the AHCI
library from writing to read-only registers.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
While most hardware will simply ignore a write to a read-only register,
some hardware will signal an abort if this occurs.
This commit introduces the flag AHCI_HFLAG_NO_WRITE_TO_RO to prevent the
AHCI library from attempting to write to the HOST_CAP, HOST_CAP2, and
HOST_PORTS_IMPL registers which may be read-only.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some hardware is capable of supporting Aggresive Link Power Management
even though it is not indicated by the Host Capability register.
This commit adds the AHCI_HFLAG_YES_ALPM flag to the AHCI library to
allow indication of this quirk when the Host Capability register is
Read Only and therefore cannot be changed.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The new driver uses an incorrect format string for resource_size_t:
drivers/ata/pata_ftide010.c: In function 'pata_ftide010_probe':
drivers/ata/pata_ftide010.c:520:17: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'resource_size_t {aka long long unsigned int}' [-Wformat=]
The nicest way to print the address is to pretty-print the resource
using %pR.
Fixes: be4e456ed3 ("ata: Add driver for Faraday Technology FTIDE010")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
The function name used to be ata_scsiop_mode_select() but renamed to
ata_scsi_mode_select_xlat(). Update the comment accordingly.
tj: Minor commit desc update.
Signed-off-by: Minwoo Im <dn3108@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
3946 2296 0 6242 1862 drivers/ata/sata_rcar.o
File size after constify sata_rcar_match.
text data bss dec hex filename
5554 696 0 6250 186a drivers/ata/sata_rcar.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
465 696 4 1165 48d drivers/ata/pata_octeon_cf.o
File size after constify octeon_cf_match.
text data bss dec hex filename
865 280 4 1149 47d drivers/ata/pata_octeon_cf.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Linus Torvalds changed the behavior of printks without KERN_<LEVEL>.
Convert the continuation prints to use pr_cont.
At the same time, convert the existing printks with KERN_<LEVEL> to
pr_<level>
Miscellanea:
o Coalesce a multiline format
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
AHCI 1.3.1 Spec says that software shall build two H2D register
FISes in the command list to send a software reset.
The comments in ahci_do_softreset() is currently D2H instead of H2D.
Signed-off-by: Minwoo Im <dn3108@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_port_info structures are either copied to other objects or their
references are stored in objects of type const. So, ata_port_info
structures having similar usage pattern can be made const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This adds a driver for the Faraday Technology FTIDE010
PATA IP block.
When used with the Storlink/Storm/Cortina Systems Gemini
SoC, the PATA interface is accompanied by a PATA<->SATA
bridge, so while the device appear as a PATA controller,
it attaches physically to SATA disks, and also has a
designated memory area with registers to set up the bridge.
The Gemini SATA bridge is separated into its own driver
file to make things modular and make it possible to reuse
the PATA driver as stand-alone on other systems than the
Gemini.
dmesg excerpt from the D-Link DIR-685 storage router:
gemini-sata-bridge 46000000.sata: SATA ID 00000e00, PHY ID: 01000100
gemini-sata-bridge 46000000.sata: set up the Gemini IDE/SATA nexus
ftide010 63000000.ata: set up Gemini PATA0
ftide010 63000000.ata: device ID 00000500, irq 26, io base 0x63000000
ftide010 63000000.ata: SATA0 (master) start
gemini-sata-bridge 46000000.sata: SATA0 PHY ready
scsi host0: pata-ftide010
ata1: PATA max UDMA/133 irq 26
ata1.00: ATA-8: INTEL SSDSA2CW120G3, 4PC10302, max UDMA/133
ata1.00: 234441648 sectors, multi 1: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA INTEL SSDSA2CW12 0302 PQ: 0 ANSI: 5
ata1.00: Enabling discard_zeroes_data
sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/112 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
ata1.00: Enabling discard_zeroes_data
ata1.00: Enabling discard_zeroes_data
sd 0:0:0:0: [sda] Attached SCSI disk
After this I can flawlessly mount and read/write copy etc files
from /dev/sda[n].
Cc: John Feng-Hsin Chiang <john453@faraday-tech.com>
Cc: Greentime Hu <green.hu@gmail.com>
Acked-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
tj: Updated line continuation style for consistency as pointed out by
Sergei.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
It is core functionality, and only one of the users is in the EH code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Ls1088a is new introduced arm-based soc with sata support with
following features:
* Complies with the serial ATA 3.0 specification
and the AHCI 1.3.1 specification
* Contains a high-speed descriptor-based DMA controller
* Supports the following:
* Speeds of 1.5 Gb/s (first-generation SATA),
3 Gb/s (second-generation SATA), and 6 Gb/s (third-generation SATA)
* FIS-based switching
* Native command queuing (NCQ) commands
* Port multiplier operation
* Asynchronous notification
* SATA Vendor BIST mode
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_parse_force_one() was incorrectly comparing @p to @endp when it
should have been comparing @id. The only consequence is that it may
end up using an invalid port number in "libata.force" module param
instead of rejecting it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Petru-Florin Mihancea <petrum@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195785
ata_host_alloc_pinfo() assigns the host pointer to the
struct device * drvdata, do not assign it a second time.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_host_alloc_pinfo() assigns the host pointer to the
struct device * drvdata, do not assign it a second time.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_host_alloc_pinfo() assigns the host pointer to the
struct device * drvdata, do not assign it a second time.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_host_alloc_pinfo() assigns the host pointer to the
struct device * drvdata, do not assign it a second time.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_host_alloc_pinfo() assigns the host pointer to the
struct device * drvdata, do not assign drv_data like this.
Since ata_host_alloc_pinfo() is called after this site, the
correct value is set eventually, but this assignment is just
plain pointless.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_host_alloc_pinfo() assigns the host pointer to the
struct device * drvdata, do not assign it a second time.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
This reverts commit 368e5fbdfc.
devm_ioremap_resource() enforces that there are no overlapping
resources, where as devm_ioremap() does not. The sata phy driver needs
a subset of the sata IO address space, so maps some of the sata
address space. As a result, sata_mv now fails to probe, reporting it
cannot get its resources, and so we don't have any SATA disks.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Tejun Heo <tj@kernel.org>
The libata documentation is now using ReST. Update references
to it to point to the new place.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When platform_get_irq() fails, it returns an error code, which
libahci_platform and replaces it by -EINVAL. This commit fixes that by
propagating the error code. It fixes the situation where
platform_get_irq() returns -EPROBE_DEFER because the interrupt
controller is not available yet, and generally looks like the right
thing to do.
We pay attention to not show the "no irq" message when we are in an
EPROBE_DEFER situation, because the driver probing will be retried
later on, once the interrupt controller becomes available to provide
the interrupt.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Here, Clock enable can failed. So adding an error check for
clk_prepare_enable.
tj: minor style updates
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
(Correction in this resend: fixed function name acer_sa5_271_workaround; fixed
the always-true condition in the function; fixed description.)
On the Acer Switch Alpha 12 (model number: SA5-271), the internal SSD may not
get detected because the port_map and CAP.nr_ports combination causes the driver
to skip the port that is actually connected to the SSD. More specifically,
either all SATA ports are identified as DUMMY, or all ports get ``link down''
and never get up again.
This problem occurs occasionally. When this problem occurs, CAP may hold a
value of 0xC734FF00 or 0xC734FF01 and port_map may hold a value of 0x00 or 0x01.
When this problem does not occur, CAP holds a value of 0xC734FF02 and port_map
may hold a value of 0x07. Overriding the CAP value to 0xC734FF02 and port_map to
0x7 significantly reduces the occurrence of this problem.
Link: https://bugzilla.kernel.org/attachment.cgi?id=253091
Signed-off-by: Sui Chen <suichen6@gmail.com>
Tested-by: Damian Ivanov <damianatorrpm@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
The XPFO [1] patchset may unmap pages from physmap if they happened to be
destined for userspace. If such a page is unmapped, it needs to be
remapped. Rather than test if a page is in the highmem/xpfo unmapped state,
Christoph suggested [2] that we simply always map the page.
v2: * drop comment about bounce buffer
* don't save IRQs before kmap/unmap
* formatting
[1]: https://lkml.org/lkml/2016/11/4/245
[2]: https://lkml.org/lkml/2016/11/4/253
Suggested-and-reviewed-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tycho Andersen <tycho@docker.com>
CC: Juerg Haefliger <juerg.haefliger@hpe.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The libata documentation is now using ReST. Update references
to it to point to the new place.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Driver updates for ARM SoCs.
* Reset subsystem, merged through arm-soc by tradition:
- Make bool drivers explicitly non-modular
- New support for i.MX7 and Arria10 reset controllers
* PATA driver for Palmchip BK371 (acked by Tejun)
* Power domain drivers for i.MX (GPC, GPCv2)
- Moved out of mach-imx for GPC
- Bunch of tweaks, fixes, etc
* PMC support for Tegra186
* SoC detection support for Renesas RZ/G1H and RZ/G1N
* Move Tegra flow controller driver from mach directory to drivers/soc
- (Power management / CPU power driver)
* Misc smaller tweaks for other platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=B43K
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs:
Reset subsystem, merged through arm-soc by tradition:
- Make bool drivers explicitly non-modular
- New support for i.MX7 and Arria10 reset controllers
PATA driver for Palmchip BK371 (acked by Tejun)
Power domain drivers for i.MX (GPC, GPCv2)
- Moved out of mach-imx for GPC
- Bunch of tweaks, fixes, etc
PMC support for Tegra186
SoC detection support for Renesas RZ/G1H and RZ/G1N
Move Tegra flow controller driver from mach directory to drivers/soc
- (Power management / CPU power driver)
Misc smaller tweaks for other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
soc: pm-domain: Fix the mangled urls
soc: renesas: rcar-sysc: Add support for R-Car H3 ES2.0
soc: renesas: rcar-sysc: Add support for fixing up power area tables
soc: renesas: Register SoC device early
soc: imx: gpc: add workaround for i.MX6QP to the GPC PD driver
dt-bindings: imx-gpc: add i.MX6 QuadPlus compatible
soc: imx: gpc: add defines for domain index
soc: imx: Add GPCv2 power gating driver
dt-bindings: Add GPCv2 power gating driver
ARM/clk: move the ICST library to drivers/clk
ARM: plat-versatile: remove stale clock header
ARM: keystone: Drop PM domain support for k2g
soc: ti: Add ti_sci_pm_domains driver
dt-bindings: Add TI SCI PM Domains
PM / Domains: Do not check if simple providers have phandle cells
PM / Domains: Add generic data pointer to genpd data struct
soc/tegra: Add initial flowctrl support for Tegra132/210
soc/tegra: flowctrl: Add basic platform driver
soc/tegra: Move Tegra flowctrl driver
ARM: tegra: Remove unnecessary inclusion of flowctrl header
...
Pull libata updates from Tejun Heo:
"The biggest core change is removal of SCT WRITE SAME support, which
never worked properly.
Other than that, trivial updates in core code and specific embedded
driver updates"
* 'for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: remove SCT WRITE SAME support
libata: reject passthrough WRITE SAME requests
dt-bindings: ata: add DT bindings for ahci-dm816 SATA controller
ata: ahci: add support for DaVinci DM816 SATA controller
pata: remove the at91 driver
libata: make ata_sg_clean static over again
libata: use setup_deferrable_timer
ata: allow subsystem to be used on m32r and s390 archs
Delete redundant return value check of platform_get_resource()
ata: constify of_device_id structures
This was already disabled a while ago because it caused I/O errors,
and it's severly getting into the way of the discard / write zeroes
rework.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The WRITE SAME to TRIM translation rewrites the DATA OUT buffer. While
the SCSI code accomodates for this by passing a read-writable buffer
userspace applications don't cater for this behavior. In fact it can
be used to rewrite e.g. a readonly file through mmap and should be
considered as a security fix.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Clear IORDYINT, INTRSTAT and DMAERROR bits of BMISP register
(value '1' needs to be written to the bit to clear it).
Suggested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This reverts commit 5946fdaee4.
The original commit's assumption that the secondary port is
unconnected turns out to be false.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Markku Pesonen <tourula@gmail.com>
Fixes: 5946fdaee4 ("pata_atiixp: Don't use unconnected secondary port on SB600/SB700")
Cc: Darren Stevens <darren@stevens-zone.net>
This SATA controller is quite similar to the one present on the DA850
SoC, but the PHY configuration is different and it supports two HBA
ports.
The IP suffers from the same PMP issue the DA850 does - if we enable
PMP but don't use it - softreset fails. Appropriate workaround was
implemented in this driver as well.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This driver is orphan since commit b2026f708e ("ARM: at91: remove
at91sam9260/at91sam9g20 legacy board support"). Given that nobody cared
adding DT support to it, it probably means it's no longer used and is
thus a good candidate for removal.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes the following sparse warning:
drivers/ata/libata-core.c:4913:6: warning: symbol 'ata_sg_clean' was not
declared. Should it be static?
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Use setup_deferrable_timer() instead of init_timer_deferrable() to
simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Sata ecc is controlled by only 1 bit which is 24bit in big-endian
in ecc register. So only setting 24bit to disable sata ecc prevents
other bits from being overwritten in ecc register.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Anurag Kumar Vulisha