Fixes: commit bc6b1e7b86
ARM: OMAP: gpmc: add DT bindings for GPMC timings and NAND
OMAP SoC(s) depend on GPMC controller driver to parse GPMC DT child nodes and
register them platform_device for NAND driver to probe later. However this does
not happen if generic MTD_NAND framework is built as module (CONFIG_MTD_NAND=m).
Therefore, when MTD/NAND and MTD/NAND/OMAP2 modules are loaded, they are unable
to find any matching platform_device and remain un-binded. This causes on board
NAND flash to remain un-detected.
This patch causes GPMC controller to parse DT nodes when
CONFIG_MTD_NAND=y || CONFIG_MTD_NAND=m
CC: <stable@vger.kernel.org> # 3.9.x+
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Does not have an aux supply, and must be non-removable.
Otherwise it is removed during suspend and filesystem gets confused.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP5, DRA7, AM43xx all have OPPs. So select the same to allow SoC
only configuration boot to work with OPP.
Reported-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pinctrl section and cd-gpio to mmc1. Without these the SD card is not
working on EVM-SK board.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clock for audio is sourced from virt_24000000_ck, so the correct
frequency is 24000000.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BMP085 EOC (End Of Conversion) irq line is connected to
gpio113 on gta04. Set irq properties to have driver using irq
instead polling for EOC.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If CONFIG_X86_SMAP is disabled, smap_violation() tests for conditions
which are incorrect (as the AC flag doesn't matter), causing spurious
faults.
The dynamic disabling of SMAP (nosmap on the command line) is fine
because it disables X86_FEATURE_SMAP, therefore causing the
static_cpu_has() to return false.
Found by Fengguang Wu's test system.
[ v3: move all predicates into smap_violation() ]
[ v2: use IS_ENABLED() instead of #ifdef ]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Link: http://lkml.kernel.org/r/20140213124550.GA30497@localhost
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.7+
If SMAP support is not compiled into the kernel, don't enable SMAP in
CR4 -- in fact, we should clear it, because the kernel doesn't contain
the proper STAC/CLAC instructions for SMAP support.
Found by Fengguang Wu's test system.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Link: http://lkml.kernel.org/r/20140213124550.GA30497@localhost
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.7+
Pull powerpc updates from Ben Herrenschmidt:
"Here is some powerpc goodness for -rc2. Arguably -rc1 material more
than -rc2 but I was travelling (again !)
It's mostly bug fixes including regressions, but there are a couple of
new things that I decided to drop-in.
One is a straightforward patch from Michael to add a bunch of P8 cache
events to perf.
The other one is a patch by myself to add the direct DMA (iommu
bypass) for PCIe on Power8 for 64-bit capable devices. This has been
around for a while, I had lost track of it. However it's been in our
internal kernels we use for testing P8 already and it affects only P8
related code. Since P8 is still unreleased the risk is pretty much
nil at this point"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/powernv: Add iommu DMA bypass support for IODA2
powerpc: Fix endian issues in kexec and crash dump code
powerpc/ppc32: Fix the bug in the init of non-base exception stack for UP
powerpc/xmon: Don't signal we've entered until we're finished printing
powerpc/xmon: Fix timeout loop in get_output_lock()
powerpc/xmon: Don't loop forever in get_output_lock()
powerpc/perf: Configure BHRB filter before enabling PMU interrupts
crypto/nx/nx-842: Fix handling of vmalloc addresses
powerpc/pseries: Select ARCH_RANDOM on pseries
powerpc/perf: Add Power8 cache & TLB events
powerpc/relocate fix relocate processing in LE mode
powerpc: Fix kdump hang issue on p8 with relocation on exception enabled.
powerpc/pseries: Disable relocation on exception while going down during crash.
powerpc/eeh: Drop taken reference to driver on eeh_rmv_device
powerpc: Fix build failure in sysdev/mpic.c for MPIC_WEIRD=y
When the conversion was made to remove stop machine and use the breakpoint
logic instead, the modification of the function graph caller is still
done directly as though it was being done under stop machine.
As it is not converted via stop machine anymore, there is a possibility
that the code could be layed across cache lines and if another CPU is
accessing that function graph call when it is being updated, it could
cause a General Protection Fault.
Convert the update of the function graph caller to use the breakpoint
method as well.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: stable@vger.kernel.org # 3.5+
Fixes: 08d636b6d4 "ftrace/x86: Have arch x86_64 use breakpoints instead of stop machine"
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Pull s390 bugfixes from Martin Schwidefsky:
"A collection a bug fixes. Most of them are minor but two of them are
more severe. The linkage stack bug can be used by user space to force
an oops, with panic_on_oops this is a denial-of-service. And the dump
memory detection issue can cause incomplete memory dumps"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/cio: improve cio_commit_config
s390: fix kernel crash due to linkage stack instructions
s390/dump: Fix dump memory detection
s390/appldata: restore missing init_virt_timer()
s390/qdio: correct program-controlled interruption checking
s390/qdio: for_each macro correctness
Pull networking updates from David Miller:
1) Fix flexcan build on big endian, from Arnd Bergmann
2) Correctly attach cpsw to GPIO bitbang MDIO drive, from Stefan Roese
3) udp_add_offload has to use GFP_ATOMIC since it can be invoked from
non-sleepable contexts. From Or Gerlitz
4) vxlan_gro_receive() does not iterate over all possible flows
properly, fix also from Or Gerlitz
5) CAN core doesn't use a proper SKB destructor when it hooks up
sockets to SKBs. Fix from Oliver Hartkopp
6) ip_tunnel_xmit() can use an uninitialized route pointer, fix from
Eric Dumazet
7) Fix address family assignment in IPVS, from Michal Kubecek
8) Fix ath9k build on ARM, from Sujith Manoharan
9) Make sure fail_over_mac only applies for the correct bonding modes,
from Ding Tianhong
10) The udp offload code doesn't use RCU correctly, from Shlomo Pongratz
11) Handle gigabit features properly in generic PHY code, from Florian
Fainelli
12) Don't blindly invoke link operations in
rtnl_link_get_slave_info_data_size, they are optional. Fix from
Fernando Luis Vazquez Cao
13) Add USB IDs for Netgear Aircard 340U, from Bjørn Mork
14) Handle netlink packet padding properly in openvswitch, from Thomas
Graf
15) Fix oops when deleting chains in nf_tables, from Patrick McHardy
16) Fix RX stalls in xen-netback driver, from Zoltan Kiss
17) Fix deadlock in mac80211 stack, from Emmanuel Grumbach
18) inet_nlmsg_size() forgets to consider ifa_cacheinfo, fix from Geert
Uytterhoeven
19) tg3_change_mtu() can deadlock, fix from Nithin Sujir
20) Fix regression in setting SCTP local source addresses on accepted
sockets, caused by some generic ipv6 socket changes. Fix from
Matija Glavinic Pecotic
21) IPPROTO_* must be pure defines, otherwise module aliases don't get
constructed properly. Fix from Jan Moskyto
22) IPV6 netconsole setup doesn't work properly unless an explicit
source address is specified, fix from Sabrina Dubroca
23) Use __GFP_NORETRY for high order skb page allocations in
sock_alloc_send_pskb and skb_page_frag_refill. From Eric Dumazet
24) Fix a regression added in netconsole over bridging, from Cong Wang
25) TCP uses an artificial offset of 1ms for SRTT, but this doesn't jive
well with TCP pacing which needs the SRTT to be accurate. Fix from
Eric Dumazet
26) Several cases of missing header file includes from Rashika Kheria
27) Add ZTE MF667 device ID to qmi_wwan driver, from Raymond Wanyoike
28) TCP Small Queues doesn't handle nonagle properly in some corner
cases, fix from Eric Dumazet
29) Remove extraneous read_unlock in bond_enslave, whoops. From Ding
Tianhong
30) Fix 9p trans_virtio handling of vmalloc buffers, from Richard Yao
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (136 commits)
6lowpan: fix lockdep splats
alx: add missing stats_lock spinlock init
9p/trans_virtio.c: Fix broken zero-copy on vmalloc() buffers
bonding: remove unwanted bond lock for enslave processing
USB2NET : SR9800 : One chip USB2.0 USB2NET SR9800 Device Driver Support
tcp: tsq: fix nonagle handling
bridge: Prevent possible race condition in br_fdb_change_mac_address
bridge: Properly check if local fdb entry can be deleted when deleting vlan
bridge: Properly check if local fdb entry can be deleted in br_fdb_delete_by_port
bridge: Properly check if local fdb entry can be deleted in br_fdb_change_mac_address
bridge: Fix the way to check if a local fdb entry can be deleted
bridge: Change local fdb entries whenever mac address of bridge device changes
bridge: Fix the way to find old local fdb entries in br_fdb_change_mac_address
bridge: Fix the way to insert new local fdb entries in br_fdb_changeaddr
bridge: Fix the way to find old local fdb entries in br_fdb_changeaddr
tcp: correct code comment stating 3 min timeout for FIN_WAIT2, we only do 1 min
net: vxge: Remove unused device pointer
net: qmi_wwan: add ZTE MF667
3c59x: Remove unused pointer in vortex_eisa_cleanup()
net: fix 'ip rule' iif/oif device rename
...
Commit 70b41abc15
"ARM: ux500: move MSP pin control to the device tree"
accidentally activated MSP2, giving rise to a boot scroll
scream as the kernel attempts to probe a driver for it and
fails to obtain DMA channel 14.
Fix this up by marking the node disabled again.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
GFP_ATOMIC is not a single gfp flag, but a macro which expands to the other
flags, where meaningful is the LACK of __GFP_WAIT flag. To check if caller
wants to perform an atomic allocation, the code must test for a lack of the
__GFP_WAIT flag. This patch fixes the issue introduced in v3.5-rc1.
CC: stable@vger.kernel.org
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
GFP_ATOMIC is not a single gfp flag, but a macro which expands to the other
flags and LACK of __GFP_WAIT flag. To check if caller wanted to perform an
atomic allocation, the code must test __GFP_WAIT flag presence. This patch
fixes the issue introduced in v3.6-rc5
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: stable@vger.kernel.org
This patch adds the support for to create a direct iommu "bypass"
window on IODA2 bridges (such as Power8) allowing to bypass iommu
page translation completely for 64-bit DMA capable devices, thus
significantly improving DMA performances.
Additionally, this adds a hook to the struct iommu_table so that
the IOMMU API / VFIO can disable the bypass when external ownership
is requested, since in that case, the device will be used by an
environment such as userspace or a KVM guest which must not be
allowed to bypass translations.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Recent changes to the pwm-backlight driver have made the power supply
mandatory. There is code in the regulator core to deal with situations
where no regulator is specified and provide a dummy, but that works on
DT-based boards only.
The situation can be remedied by adding a dummy regulator during board
initialization.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
We expose a number of OF properties in the kexec and crash dump code
and these need to be big endian.
Cc: stable@vger.kernel.org # v3.13
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We would allocate one specific exception stack for each kind of
non-base exceptions for every CPU. For ppc32 the CPU hard ID is
used as the subscript to get the specific exception stack for
one CPU. But for an UP kernel, there is only one element in the
each kind of exception stack array. We would get stuck if the
CPU hard ID is not equal to '0'. So in this case we should use the
subscript '0' no matter what the CPU hard ID is.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we set our cpu's bit in cpus_in_xmon, and then we take the
output lock and print the exception information.
This can race with the master cpu entering the command loop and printing
the backtrace. The result is that the backtrace gets garbled with
another cpu's exception print out.
Fix it by delaying the set of cpus_in_xmon until we are finished
printing.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As far as I can tell, our 70s era timeout loop in get_output_lock() is
generating no code.
This leads to the hostile takeover happening more or less simultaneously
on all cpus. The result is "interesting", some example output that is
more readable than most:
cpu 0x1: Vector: 100 (Scypsut e0mx bR:e setV)e catto xc0p:u[ c 00
c0:0 000t0o0V0erc0td:o5 rfc28050000]0c00 0 0 0 6t(pSrycsV1ppuot
uxe 1m 2 0Rx21e3:0s0ce000c00000t00)00 60602oV2SerucSayt0y 0p 1sxs
Fix it by using udelay() in the timeout loop. The wait time and check
frequency are arbitrary, but seem to work OK. We already rely on
udelay() working so this is not a new dependency.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we enter with xmon_speaker != 0 we skip the first cmpxchg(), we also
skip the while loop because xmon_speaker != last_speaker (0) - meaning we
skip the second cmpxchg() also.
Following that code path the compiler sees no memory barriers and so is
within its rights to never reload xmon_speaker. The end result is we loop
forever.
This manifests as all cpus being in xmon ('c' command), but they refuse
to take control when you switch to them ('c x' for cpu # x).
I have seen this deadlock in practice and also checked the generated code to
confirm this is what's happening.
The simplest fix is just to always try the cmpxchg().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Right now the config_bhrb() PMU specific call happens after
write_mmcr0(), which actually enables the PMU for event counting and
interrupts. So there is a small window of time where the PMU and BHRB
runs without the required HW branch filter (if any) enabled in BHRB.
This can cause some of the branch samples to be collected through BHRB
without any filter applied and hence affects the correctness of
the results. This patch moves the BHRB config function call before
enabling interrupts.
Here are some data points captured via trace prints which depicts how we
could get PMU interrupts with BHRB filter NOT enabled with a standard
perf record command line (asking for branch record information as well).
$ perf record -j any_call ls
Before the patch:-
ls-1962 [003] d... 2065.299590: .perf_event_interrupt: MMCRA: 40000000000
ls-1962 [003] d... 2065.299603: .perf_event_interrupt: MMCRA: 40000000000
...
All the PMU interrupts before this point did not have the requested
HW branch filter enabled in the MMCRA.
ls-1962 [003] d... 2065.299647: .perf_event_interrupt: MMCRA: 40040000000
ls-1962 [003] d... 2065.299662: .perf_event_interrupt: MMCRA: 40040000000
After the patch:-
ls-1850 [008] d... 190.311828: .perf_event_interrupt: MMCRA: 40040000000
ls-1850 [008] d... 190.311848: .perf_event_interrupt: MMCRA: 40040000000
All the PMU interrupts have the requested HW BHRB branch filter
enabled in MMCRA.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Fixed up whitespace and cleaned up changelog]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have a driver for the ARCH_RANDOM hook in rng.c, so we should select
ARCH_RANDOM on pseries.
Without this the build breaks if you turn ARCH_RANDOM off.
This hasn't broken the build because pseries_defconfig doesn't specify a
value for PPC_POWERNV, which is default y, and selects ARCH_RANDOM.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Relocation's code is not working in little endian mode because the r_info
field, which is a 64 bits value, should be read from the right offset.
The current code is optimized to read the r_info field as a 32 bits value
starting at the middle of the double word (offset 12). When running in LE
mode, the read value is not correct since only the MSB is read.
This patch removes this optimization which consist to deal with a 32 bits
value instead of a 64 bits one. This way it works in big and little endian
mode.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On p8 systems, with relocation on exception feature enabled we are seeing
kdump kernel hang at interrupt vector 0xc*4400. The reason is, with this
feature enabled, exception are raised with MMU (IR=DR=1) ON with the
default offset of 0xc*4000. Since exception is raised in virtual mode it
requires the vector region to be executable without which it fails to
fetch and execute instruction at 0xc*4xxx. For default kernel since kernel
is loaded at real 0, the htab mappings sets the entire kernel text region
executable. But for relocatable kernel (e.g. kdump case) we only copy
interrupt vectors down to real 0 and never marked that region as
executable because in p7 and below we always get exception in real mode.
This patch fixes this issue by marking htab mapping range as executable
that overlaps with the interrupt vector region for relocatable kernel.
Thanks to Ben who helped me to debug this issue and find the root cause.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Disable relocation on exception while going down even in kdump case. This
is because we are about clear htab mappings while kexec-ing into kdump
kernel and we may run into issues if we still have AIL ON.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit f5c57710dd ("powerpc/eeh: Use
partial hotplug for EEH unaware drivers") introduces eeh_rmv_device,
which may grab a reference to a driver, but not release it.
That prevents a driver from being removed after it has gone through EEH
recovery.
This patch drops the reference if it was taken.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 446f6d06fa ("powerpc/mpic: Properly
set default triggers") breaks the mpc7447_hpc_defconfig as follows:
CC arch/powerpc/sysdev/mpic.o
arch/powerpc/sysdev/mpic.c: In function 'mpic_set_irq_type':
arch/powerpc/sysdev/mpic.c:886:9: error: case label does not reduce to an integer constant
arch/powerpc/sysdev/mpic.c:890:9: error: case label does not reduce to an integer constant
arch/powerpc/sysdev/mpic.c:894:9: error: case label does not reduce to an integer constant
arch/powerpc/sysdev/mpic.c:898:9: error: case label does not reduce to an integer constant
Looking at the cpp output (gcc 4.7.3), I see:
case mpic->hw_set[MPIC_IDX_VECPRI_SENSE_EDGE] |
mpic->hw_set[MPIC_IDX_VECPRI_POLARITY_POSITIVE]:
The pointer into an array appears because CONFIG_MPIC_WEIRD=y is set
for this platform, thus enabling the following:
-------------------
#ifdef CONFIG_MPIC_WEIRD
static u32 mpic_infos[][MPIC_IDX_END] = {
[0] = { /* Original OpenPIC compatible MPIC */
[...]
#define MPIC_INFO(name) mpic->hw_set[MPIC_IDX_##name]
#else /* CONFIG_MPIC_WEIRD */
#define MPIC_INFO(name) MPIC_##name
#endif /* CONFIG_MPIC_WEIRD */
-------------------
Here we convert the case section to if/else if, and also add
the equivalent of a default case to warn about unknown types.
Boot tested on sbc8548, build tested on all defconfigs.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Steven Noonan forwarded a users report where they had a problem starting
vsftpd on a Xen paravirtualized guest, with this in dmesg:
BUG: Bad page map in process vsftpd pte:8000000493b88165 pmd:e9cc01067
page:ffffea00124ee200 count:0 mapcount:-1 mapping: (null) index:0x0
page flags: 0x2ffc0000000014(referenced|dirty)
addr:00007f97eea74000 vm_flags:00100071 anon_vma:ffff880e98f80380 mapping: (null) index:7f97eea74
CPU: 4 PID: 587 Comm: vsftpd Not tainted 3.12.7-1-ec2 #1
Call Trace:
dump_stack+0x45/0x56
print_bad_pte+0x22e/0x250
unmap_single_vma+0x583/0x890
unmap_vmas+0x65/0x90
exit_mmap+0xc5/0x170
mmput+0x65/0x100
do_exit+0x393/0x9e0
do_group_exit+0xcc/0x140
SyS_exit_group+0x14/0x20
system_call_fastpath+0x1a/0x1f
Disabling lock debugging due to kernel taint
BUG: Bad rss-counter state mm:ffff880e9ca60580 idx:0 val:-1
BUG: Bad rss-counter state mm:ffff880e9ca60580 idx:1 val:1
The issue could not be reproduced under an HVM instance with the same
kernel, so it appears to be exclusive to paravirtual Xen guests. He
bisected the problem to commit 1667918b64 ("mm: numa: clear numa
hinting information on mprotect") that was also included in 3.12-stable.
The problem was related to how xen translates ptes because it was not
accounting for the _PAGE_NUMA bit. This patch splits pte_present to add
a pteval_present helper for use by xen so both bare metal and xen use
the same code when checking if a PTE is present.
[mgorman@suse.de: wrote changelog, proposed minor modifications]
[akpm@linux-foundation.org: fix typo in comment]
Reported-by: Steven Noonan <steven@uplinklabs.net>
Tested-by: Steven Noonan <steven@uplinklabs.net>
Signed-off-by: Elena Ufimtseva <ufimtseva@gmail.com>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <stable@vger.kernel.org> [3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The address for control regs in clkvcp3 node is not correct and should
be 0x023500a8 instead of 0x0235000a8.
This lead to few unexpected behaviors while clocks were turned
of in absence of clk_ignore_unused
Mike Turquette <mturquette@linaro.org>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reserve space from 0x0 - __pa(swapper_pg_dir),
if kernel is loaded from 0, which is not DMAable.
It is causing problem with MMC driver and others
which want to add dma buffers to this space.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
All of them are DT-related.
- fixes for typos in i2c and ohci clocks
- addition of a USB host node for at91sam9n12ek
- 2 DT documentation updates that have been sent a long time ago
- a new board based on the sama5d36 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJS9QjhAAoJEAf03oE53VmQwwMIAMj6mM4Fv042REUssGIeVGlk
kmt3NzFeQI2ipTsgdwloAd53Hvty9RiX0ww4ZIGnxy8eZdEaRy6aDCohQsCvfYtx
LDcGdmIZ9056+62h/dqEbKYzs23j+diSJPe5sJF3/EHRRrRtBLSccEjnAMYI+Vqx
Gpj4XplbG89yXQZb1sKCCo9OsScu1ncdXs6G1ghZt1WhcvDwRuf/C0Af5KYCOibs
iXyMYxw7dd2VS8DxABxfi4xhW/ZZFR5ml66XdEW6MQLRG5Z33v7v7S9Wt0DV8uqd
C+naFnbm09/miHFX8bGZeI1Yaavs+UhKdD86fCn0Mn4uHNr4IdqqLGPEkZpjyJA=
=m41s
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes
From Nicolas Ferre:
First series of AT91 fixes for 3.14.
All of them are DT-related.
- fixes for typos in i2c and ohci clocks
- addition of a USB host node for at91sam9n12ek
- 2 DT documentation updates that have been sent a long time ago
- a new board based on the sama5d36 SoC
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: add Atmel's SAMA5D3 Xplained board
spi/atmel: document clock properties
mmc: atmel-mci: document clock properties
ARM: at91: enable USB host on at91sam9n12ek board
ARM: at91/dt: fix sama5d3 ohci hclk clock reference
ARM: at91/dt: sam9263: fix compatibility string for the I2C
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Select CONFIG_SOC_DRA7XX so that we can boot dra7-evm.
DRA7 family are A15 based processors that supports LPAE and an
evolutionary update to the OMAP5 generation of processors.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Since commit 9e8147bb5e
"ARM: imx6q: move low-power code out of clock driver"
the kernel fails to boot on i.MX6Q/D if preemption is
enabled (CONFIG_PREEMPT=y). The kernel just hangs
before the console comes up.
The above commit moved the initalization of the low-power
mode setting (enabling clocked WAIT states), which was
introduced in commit 83ae20981a
"ARM: imx: correct low-power mode setting", from
imx6q_clks_init to imx6q_pm_init. Now it is called
much later, after all cores are enabled.
This patch moves the low-power mode initialization back
to imx6q_clks_init again (and to imx6sl_clks_init).
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Due to commit 88f718e3fa
"ARM: pxa: delete the custom GPIO header" some drivers fail
compilation, for example like this:
In file included from sound/soc/pxa/spitz.c:28:0:
sound/soc/pxa/spitz.c: In function ‘spitz_ext_control’:
arch/arm/mach-pxa/include/mach/spitz.h:111:30: error:
‘PXA_NR_BUILTIN_GPIO’ undeclared (first use in this function)
#define SPITZ_SCP_GPIO_BASE (PXA_NR_BUILTIN_GPIO)
(etc.)
This is caused by implicit inclusion of <mach/irqs.h> from
various board-specific headers under <mach/*> in the PXA
platform. So we take a sweep over these, and for every such
header that uses PXA_NR_BUILTIN_GPIO or PXA_GPIO_TO_IRQ()
we explicitly #include "irqs.h" so that we satisfy the
dependency in the board include file alone.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Kevin Hilman <khilman@linaro.org>
This board fails compilation like this:
arch/arm/mach-pxa/am300epd.c: In function ‘am300_cleanup’:
arch/arm/mach-pxa/am300epd.c:179:2: error: implicit declaration
of function ‘PXA_GPIO_TO_IRQ’ [-Werror=implicit-function-declaration]
free_irq(PXA_GPIO_TO_IRQ(RDY_GPIO_PIN), par);
This was caused by commit 88f718e3fa
"ARM: pxa: delete the custom GPIO header"
This is because it was previously getting the macro PXA_GPIO_TO_IRQ
implicitly from <linux/gpio.h> which in turn implicitly included
<mach/gpio.h> which in turn included <mach/irqs.h>.
Add the missing include so that the board compiles again.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
When unlocking a spinlock, we require the following, strictly ordered
sequence of events:
<barrier> /* dmb */
<unlock>
<barrier> /* dsb */
<sev>
Whilst the code does indeed reflect this in terms of the architecture,
the final <barrier> + <sev> have been contracted into a single inline
asm without a "memory" clobber, therefore the compiler is at liberty to
reorder the unlock to the end of the above sequence. In such a case,
a waiting CPU may be woken up before the lock has been unlocked, leading
to extremely poor performance.
This patch reworks the dsb_sev() function to make use of the dsb()
macro and ensure ordering against the unlock.
Cc: <stable@vger.kernel.org>
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
During __v{6,7}_setup, we invalidate the TLBs since we are about to
enable the MMU on return to head.S. Unfortunately, without a subsequent
dsb instruction, the invalidation is not guaranteed to have completed by
the time we write to the sctlr, potentially exposing us to junk/stale
translations cached in the TLB.
This patch reworks the init functions so that the dsb used to ensure
completion of cache/predictor maintenance is also used to ensure
completion of the TLB invalidation.
Cc: <stable@vger.kernel.org>
Reported-by: Albin Tonnerre <Albin.Tonnerre@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit ad6492b8 added much needed memblock_virt_alloc_low() and further
commit 07bacb3 {memblock, bootmem: restore goal for alloc_low} fixed
the issue with low memory limit thanks to Yinghai. But even after all
these fixes, there is still one case where the limit check done with
ARCH_LOW_ADDRESS_LIMIT for low memory fails. Russell pointed out the
issue with 32 bit LPAE machines in below thread.
https://lkml.org/lkml/2014/1/28/364
Since on some LPAE machines where memory start address is beyond 4GB,
the low memory marker in memblock will be set to default
ARCH_LOW_ADDRESS_LIMIT which is wrong. We can fix this by letting
architectures set the ARCH_LOW_ADDRESS_LIMIT using another export
similar to memblock_set_current_limit() but am not sure whether
its worth the trouble. Tell me if you think otherwise.
Rather am just trying to fix that one broken case using
memblock_virt_alloc() in setup code since the memblock.current_limit
is updated appropriately makes it work on all ARM 32 bit machines.
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Strashko, Grygorii <grygorii.strashko@ti.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The stage-2 memory attributes are distinct from the Hyp memory
attributes and the Stage-1 memory attributes. We were using the stage-1
memory attributes for stage-2 mappings causing device mappings to be
mapped as normal memory. Add the S2 equivalent defines for memory
attributes and fix the comments explaining the defines while at it.
Add a prot_pte_s2 field to the mem_type struct and fill out the field
for device mappings accordingly.
Cc: <stable@vger.kernel.org> [3.9+]
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Correct a typo causing the stack protector to be left enabled.
0xFFFFFFF -> 0xFFFFFFFF
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Some drivers check if readq/writeq functions are defined.
If not internal driver functions are used which cause
compilation failures.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add missing param.h header because of HZ macro.
It is causing compilation failure:
In file included from include/linux/delay.h:14:0,
from drivers/clk/qcom/reset.c:18:
drivers/clk/qcom/reset.c: In function 'qcom_reset':
arch/microblaze/include/asm/delay.h:39:35: error: 'HZ'
undeclared (first use in this function)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When debug preempt is enabled, preempt_disable() can be traced by
function and function graph tracing.
There's a place in the function graph tracer that calls trace_clock()
which eventually calls cycles_2_ns() outside of the recursion
protection. When cycles_2_ns() calls preempt_disable() it gets traced
and the graph tracer will go into a recursive loop causing a crash or
worse, a triple fault.
Simple fix is to use preempt_disable_notrace() in cycles_2_ns, which
makes sense because the preempt_disable() tracing may use that code
too, and it tracing it, even with recursion protection is rather
pointless.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20140204141315.2a968a72@gandalf.local.home
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The current code forgets to change the CR4 state on the current CPU.
Use on_each_cpu() instead of smp_call_function().
Reported-by: Mark Davies <junk@eslaf.co.uk>
Suggested-by: Mark Davies <junk@eslaf.co.uk>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: fweisbec@gmail.com
Link: http://lkml.kernel.org/n/tip-69efsat90ibhnd577zy3z9gh@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The spdif pinmux configuration must be connected to the spdif device to
take effect, not the spdif-transmitter.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull x86 fixes from Peter Anvin:
"Quite a varied little collection of fixes. Most of them are
relatively small or isolated; the biggest one is Mel Gorman's fixes
for TLB range flushing.
A couple of AMD-related fixes (including not crashing when given an
invalid microcode image) and fix a crash when compiled with gcov"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, microcode, AMD: Unify valid container checks
x86, hweight: Fix BUG when booting with CONFIG_GCOV_PROFILE_ALL=y
x86/efi: Allow mapping BGRT on x86-32
x86: Fix the initialization of physnode_map
x86, cpu hotplug: Fix stack frame warning in check_irq_vectors_for_cpu_disable()
x86/intel/mid: Fix X86_INTEL_MID dependencies
arch/x86/mm/srat: Skip NUMA_NO_NODE while parsing SLIT
mm, x86: Revisit tlb_flushall_shift tuning for page flushes except on IvyBridge
x86: mm: change tlb_flushall_shift for IvyBridge
x86/mm: Eliminate redundant page table walk during TLB range flushing
x86/mm: Clean up inconsistencies when flushing TLB ranges
mm, x86: Account for TLB flushes only when debugging
x86/AMD/NB: Fix amd_set_subcaches() parameter type
x86/quirks: Add workaround for AMD F16h Erratum792
x86, doc, kconfig: Fix dud URL for Microcode data
does not conflict with the dynamic linker's one (64K)
- VDSO gettimeofday fix
- Barrier fixes for atomic operations and cache flushing
- TLB invalidation when overriding early page mappings during boot
- Wired up new 32-bit arm (compat) syscalls
- LSM_MMAP_MIN_ADDR when COMPAT is enabled
- defconfig update
- Clean-up (comments, pgd_alloc).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=jhHX
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Relax VDSO alignment requirements so that the kernel-picked one (4K)
does not conflict with the dynamic linker's one (64K)
- VDSO gettimeofday fix
- Barrier fixes for atomic operations and cache flushing
- TLB invalidation when overriding early page mappings during boot
- Wired up new 32-bit arm (compat) syscalls
- LSM_MMAP_MIN_ADDR when COMPAT is enabled
- defconfig update
- Clean-up (comments, pgd_alloc).
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: defconfig: Expand default enabled features
arm64: asm: remove redundant "cc" clobbers
arm64: atomics: fix use of acquire + release for full barrier semantics
arm64: barriers: allow dsb macro to take option parameter
security: select correct default LSM_MMAP_MIN_ADDR on arm on arm64
arm64: compat: Wire up new AArch32 syscalls
arm64: vdso: update wtm fields for CLOCK_MONOTONIC_COARSE
arm64: vdso: fix coarse clock handling
arm64: simplify pgd_alloc
arm64: fix typo: s/SERRROR/SERROR/
arm64: Invalidate the TLB when replacing pmd entries during boot
arm64: Align CMA sizes to PAGE_SIZE
arm64: add DSB after icache flush in __flush_icache_all()
arm64: vdso: prevent ld from aligning PT_LOAD segments to 64k
Pull MIPS updates from Ralf Baechle:
"hree minor patches. All have sat in -next for a few days"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: fpu.h: Fix build when CONFIG_BUG is not set
MIPS: Wire up sched_setattr/sched_getattr syscalls
MIPS: Alchemy: Fix DB1100 GPIO registration
FPGA implementations of the Cortex-A57 and Cortex-A53 are now available
in the form of the SMM-A57 and SMM-A53 Soft Macrocell Models (SMMs) for
Versatile Express. As these attach to a Motherboard Express V2M-P1 it
would be useful to have support for some V2M-P1 peripherals enabled by
default.
Additionally a couple of of features have been introduced since the last
defconfig update (CMA, jump labels) that would be good to have enabled
by default to ensure they are build and boot tested.
This patch updates the arm64 defconfig to enable support for these
devices and features. The arm64 Kconfig is modified to select
HAVE_PATA_PLATFORM, which is required to enable support for the
CompactFlash controller on the V2M-P1.
A few options which don't need to appear in defconfig are trimmed:
* BLK_DEV - selected by default
* EXPERIMENTAL - otherwise gone from the kernel
* MII - selected by drivers which require it
* USB_SUPPORT - selected by default
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
cbnz/tbnz don't update the condition flags, so remove the "cc" clobbers
from inline asm blocks that only use these instructions to implement
conditional branches.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Linux requires a number of atomic operations to provide full barrier
semantics, that is no memory accesses after the operation can be
observed before any accesses up to and including the operation in
program order.
On arm64, these operations have been incorrectly implemented as follows:
// A, B, C are independent memory locations
<Access [A]>
// atomic_op (B)
1: ldaxr x0, [B] // Exclusive load with acquire
<op(B)>
stlxr w1, x0, [B] // Exclusive store with release
cbnz w1, 1b
<Access [C]>
The assumption here being that two half barriers are equivalent to a
full barrier, so the only permitted ordering would be A -> B -> C
(where B is the atomic operation involving both a load and a store).
Unfortunately, this is not the case by the letter of the architecture
and, in fact, the accesses to A and C are permitted to pass their
nearest half barrier resulting in orderings such as Bl -> A -> C -> Bs
or Bl -> C -> A -> Bs (where Bl is the load-acquire on B and Bs is the
store-release on B). This is a clear violation of the full barrier
requirement.
The simple way to fix this is to implement the same algorithm as ARMv7
using explicit barriers:
<Access [A]>
// atomic_op (B)
dmb ish // Full barrier
1: ldxr x0, [B] // Exclusive load
<op(B)>
stxr w1, x0, [B] // Exclusive store
cbnz w1, 1b
dmb ish // Full barrier
<Access [C]>
but this has the undesirable effect of introducing *two* full barrier
instructions. A better approach is actually the following, non-intuitive
sequence:
<Access [A]>
// atomic_op (B)
1: ldxr x0, [B] // Exclusive load
<op(B)>
stlxr w1, x0, [B] // Exclusive store with release
cbnz w1, 1b
dmb ish // Full barrier
<Access [C]>
The simple observations here are:
- The dmb ensures that no subsequent accesses (e.g. the access to C)
can enter or pass the atomic sequence.
- The dmb also ensures that no prior accesses (e.g. the access to A)
can pass the atomic sequence.
- Therefore, no prior access can pass a subsequent access, or
vice-versa (i.e. A is strictly ordered before C).
- The stlxr ensures that no prior access can pass the store component
of the atomic operation.
The only tricky part remaining is the ordering between the ldxr and the
access to A, since the absence of the first dmb means that we're now
permitting re-ordering between the ldxr and any prior accesses.
From an (arbitrary) observer's point of view, there are two scenarios:
1. We have observed the ldxr. This means that if we perform a store to
[B], the ldxr will still return older data. If we can observe the
ldxr, then we can potentially observe the permitted re-ordering
with the access to A, which is clearly an issue when compared to
the dmb variant of the code. Thankfully, the exclusive monitor will
save us here since it will be cleared as a result of the store and
the ldxr will retry. Notice that any use of a later memory
observation to imply observation of the ldxr will also imply
observation of the access to A, since the stlxr/dmb ensure strict
ordering.
2. We have not observed the ldxr. This means we can perform a store
and influence the later ldxr. However, that doesn't actually tell
us anything about the access to [A], so we've not lost anything
here either when compared to the dmb variant.
This patch implements this solution for our barriered atomic operations,
ensuring that we satisfy the full barrier requirements where they are
needed.
Cc: <stable@vger.kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add DT file for new SAMA5D3 Xplained board.
This board is based on Atmel's SAMA5D36 Cortex-A5 SoC.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The hclk clock of the ohci node is referencing udphs_clk instead of
uhphs_clk.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Switch the device tree to the new compatibles introduced in the ethernet and
mdio drivers to have a common pattern accross all Allwinner SoCs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following path will cause array out of bound.
memblock_add_region() will always set nid in memblock.reserved to
MAX_NUMNODES. In numa_register_memblks(), after we set all nid to
correct valus in memblock.reserved, we called setup_node_data(), and
used memblock_alloc_nid() to allocate memory, with nid set to
MAX_NUMNODES.
The nodemask_t type can be seen as a bit array. And the index is 0 ~
MAX_NUMNODES-1.
After that, when we call node_set() in numa_clear_kernel_node_hotplug(),
the nodemask_t got an index of value MAX_NUMNODES, which is out of [0 ~
MAX_NUMNODES-1].
See below:
numa_init()
|---> numa_register_memblks()
| |---> memblock_set_node(memory) set correct nid in memblock.memory
| |---> memblock_set_node(reserved) set correct nid in memblock.reserved
| |......
| |---> setup_node_data()
| |---> memblock_alloc_nid() here, nid is set to MAX_NUMNODES (1024)
|......
|---> numa_clear_kernel_node_hotplug()
|---> node_set() here, we have an index 1024, and overflowed
This patch moves nid setting to numa_clear_kernel_node_hotplug() to fix
this problem.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Tested-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Reported-by: Dave Jones <davej@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Tested-by: Dave Jones <davej@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On-stack variable numa_kernel_nodes in numa_clear_kernel_node_hotplug()
was not initialized. So we need to initialize it.
[akpm@linux-foundation.org: use NODE_MASK_NONE, per David]
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Tested-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Reported-by: Dave Jones <davej@redhat.com>
Reported-by: David Rientjes <rientjes@google.com>
Tested-by: Dave Jones <davej@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For additional coverage, BorisO and friends unknowlingly did swap AMD
microcode with Intel microcode blobs in order to see what happens. What
did happen on 32-bit was
[ 5.722656] BUG: unable to handle kernel paging request at be3a6008
[ 5.722693] IP: [<c106d6b4>] load_microcode_amd+0x24/0x3f0
[ 5.722716] *pdpt = 0000000000000000 *pde = 0000000000000000
because there was a valid initrd there but without valid microcode in it
and the container check happened *after* the relocated ramdisk handling
on 32-bit, which was clearly wrong.
While at it, take care of the ramdisk relocation on both 32- and 64-bit
as it is done on both. Also, comment what we're doing because this code
is a bit tricky.
Reported-and-tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1391460104-7261-1-git-send-email-bp@alien8.de
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
__enable_fpu produces a build failure when CONFIG_BUG is not set:
In file included from arch/mips/kernel/cpu-probe.c:24:0:
arch/mips/include/asm/fpu.h: In function '__enable_fpu':
arch/mips/include/asm/fpu.h:77:1: error: control reaches end of non-void function [-Werror=return-type]
This is regression introduced in 3.14-rc1. Fix that.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Paul Burton <paul.burton@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6504/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The dsb instruction takes an option specifying both the target access
types and shareability domain.
This patch allows such an option to be passed to the dsb macro,
resulting in potentially more efficient code. Currently the option is
ignored until all callers are updated (unlike ARM, the option is
mandated by the assembler).
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- Revert "xen/grant-table: Avoid m2p_override during mapping" as it broke Xen ARM build.
- Fix CR4 not being set on AP processors in Xen PVH mode.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJS8AyQAAoJEFjIrFwIi8fJbD4IAJssMuaLI5CRsSWBgDFHHDFt
srVJpDOYQiDr/TxkwFCVcL4sFy9Htb3KMArU4eIBl6uMqQbGa+3rHyXcHYI219YY
XH3D8RG+9JChwsxtaeUEzwx1C8ehcygD34vtdcoQXa7eBuEi4TL3HeLifR+HrXKO
UdFrTA34FmvpVFbSuRXkZh5sd6ca9et9xHuQHM8SIY6pVokY6xaEYOp17tfPZpwM
7A6LFjUjXeugHC2L3+/H8UOHA9nSZQvnMiZOWq2Cusc2Dt2V7emzgk2wcc2CHttf
EA6GbtiJzHqMPmt5EjubI9hHdSMB31HpY4hnQE38+ucl+BwiSdRE9z2Rm4TYClg=
=IX4M
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.14-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fixes from Konrad Rzeszutek Wilk:
"Bug-fixes:
- Revert "xen/grant-table: Avoid m2p_override during mapping" as it
broke Xen ARM build.
- Fix CR4 not being set on AP processors in Xen PVH mode"
* tag 'stable/for-linus-3.14-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pvh: set CR4 flags for APs
Revert "xen/grant-table: Avoid m2p_override during mapping"
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=G2gr
-----END PGP SIGNATURE-----
Merge tag 'please-pull-ia64-syscalls' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull ia64 update from Tony Luck:
"Wire up new sched_setattr and sched_getattr syscalls"
* tag 'please-pull-ia64-syscalls' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
[IA64] Wire up new sched_setattr and sched_getattr syscalls
Pull crypto fixes from Herbert Xu:
"This fixes a number of concurrency issues on s390 where multiple users
of the same crypto transform may clobber each other's results"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: s390 - fix des and des3_ede ctr concurrency issue
crypto: s390 - fix des and des3_ede cbc concurrency issue
crypto: s390 - fix concurrency issue in aes-ctr mode
CONFIG_X86_32 doesn't map the boot services regions into the EFI memory
map (see commit 700870119f ("x86, efi: Don't map Boot Services on
i386")), and so efi_lookup_mapped_addr() will fail to return a valid
address. Executing the ioremap() path in efi_bgrt_init() causes the
following warning on x86-32 because we're trying to ioremap() RAM,
WARNING: CPU: 0 PID: 0 at arch/x86/mm/ioremap.c:102 __ioremap_caller+0x2ad/0x2c0()
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.13.0-0.rc5.git0.1.2.fc21.i686 #1
Hardware name: DellInc. Venue 8 Pro 5830/09RP78, BIOS A02 10/17/2013
00000000 00000000 c0c0df08 c09a5196 00000000 c0c0df38 c0448c1e c0b41310
00000000 00000000 c0b37bc1 00000066 c043bbfd c043bbfd 00e7dfe0 00073eff
00073eff c0c0df48 c0448ce2 00000009 00000000 c0c0df9c c043bbfd 00078d88
Call Trace:
[<c09a5196>] dump_stack+0x41/0x52
[<c0448c1e>] warn_slowpath_common+0x7e/0xa0
[<c043bbfd>] ? __ioremap_caller+0x2ad/0x2c0
[<c043bbfd>] ? __ioremap_caller+0x2ad/0x2c0
[<c0448ce2>] warn_slowpath_null+0x22/0x30
[<c043bbfd>] __ioremap_caller+0x2ad/0x2c0
[<c0718f92>] ? acpi_tb_verify_table+0x1c/0x43
[<c0719c78>] ? acpi_get_table_with_size+0x63/0xb5
[<c087cd5e>] ? efi_lookup_mapped_addr+0xe/0xf0
[<c043bc2b>] ioremap_nocache+0x1b/0x20
[<c0cb01c8>] ? efi_bgrt_init+0x83/0x10c
[<c0cb01c8>] efi_bgrt_init+0x83/0x10c
[<c0cafd82>] efi_late_init+0x8/0xa
[<c0c9bab2>] start_kernel+0x3ae/0x3c3
[<c0c9b53b>] ? repair_env_string+0x51/0x51
[<c0c9b378>] i386_start_kernel+0x12e/0x131
Switch to using early_memremap(), which won't trigger this warning, and
has the added benefit of more accurately conveying what we're trying to
do - map a chunk of memory.
This patch addresses the following bug report,
https://bugzilla.kernel.org/show_bug.cgi?id=67911
Reported-by: Adam Williamson <awilliam@redhat.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
It can take some time to validate the image, make sure
{allyes|allmod}config doesn't enable it.
I'd say randconfig will cover it often enough, and the failure is also
borderline build coverage related: you cannot really make the decoder
test fail via source level changes, only with changes in the build
environment, so I agree with Andi that we can disable this one too.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Paul Gortmaker paul.gortmaker@windriver.com>
Suggested-and-acked-by: Andi Kleen andi@firstfloor.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This changes 'do_execve()' to get the executable name as a 'struct
filename', and to free it when it is done. This is what the normal
users want, and it simplifies and streamlines their error handling.
The controlled lifetime of the executable name also fixes a
use-after-free problem with the trace_sched_process_exec tracepoint: the
lifetime of the passed-in string for kernel users was not at all
obvious, and the user-mode helper code used UMH_WAIT_EXEC to serialize
the pathname allocation lifetime with the execve() having finished,
which in turn meant that the trace point that happened after
mm_release() of the old process VM ended up using already free'd memory.
To solve the kernel string lifetime issue, this simply introduces
"getname_kernel()" that works like the normal user-space getname()
function, except with the source coming from kernel memory.
As Oleg points out, this also means that we could drop the tcomm[] array
from 'struct linux_binprm', since the pathname lifetime now covers
setup_new_exec(). That would be a separate cleanup.
Reported-by: Igor Zhbanov <i.zhbanov@samsung.com>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update wall-to-monotonic fields in the VDSO data page
unconditionally. These are used to service CLOCK_MONOTONIC_COARSE,
which is not guarded by use_syscall.
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When __kernel_clock_gettime is called with a CLOCK_MONOTONIC_COARSE or
CLOCK_REALTIME_COARSE clock id, it returns incorrectly to whatever the
caller has placed in x2 ("ret x2" to return from the fast path). Fix
this by saving x30/LR to x2 only in code that will call
__do_get_tspec, restoring x30 afterward, and using a plain "ret" to
return from the routine.
Also: while the resulting tv_nsec value for CLOCK_REALTIME and
CLOCK_MONOTONIC must be computed using intermediate values that are
left-shifted by cs_shift (x12, set by __do_get_tspec), the results for
coarse clocks should be calculated using unshifted values
(xtime_coarse_nsec is in units of actual nanoseconds). The current
code shifts intermediate values by x12 unconditionally, but x12 is
uninitialized when servicing a coarse clock. Fix this by setting x12
to 0 once we know we are dealing with a coarse clock id.
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Currently pgd_alloc has a redundant NULL check in its return path that
can be removed with no ill effects. With that removed it's also possible
to return early and eliminate the new_pgd temporary variable.
This patch applies said modifications, making the logic of pgd_alloc
correspond 1-1 with that of pgd_free.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Somehow SERROR has acquired an additional 'R' in a couple of headers.
This patch removes them before they spread further. As neither instance
is in use yet, no other sites need to be fixed up.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
With the 64K page size configuration, __create_page_tables in head.S
maps enough memory to get started but using 64K pages rather than 512M
sections with a single pgd/pud/pmd entry pointing to a pte table.
create_mapping() may override the pgd/pud/pmd table entry with a block
(section) one if the RAM size is more than 512MB and aligned correctly.
For the end of this block to be accessible, the old TLB entry must be
invalidated.
Cc: <stable@vger.kernel.org>
Reported-by: Mark Salter <msalter@redhat.com>
Tested-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
dma_alloc_from_contiguous takes number of pages for a size.
Align up the dma size passed in to page size to avoid truncation
and allocation failures on sizes less than PAGE_SIZE.
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add DSB after icache flush to complete the cache maintenance operation.
The function __flush_icache_all() is used only for user space mappings
and an ISB is not required because of an exception return before executing
user instructions. An exception return would behave like an ISB.
Signed-off-by: Vinayak Kale <vkale@apm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The kernel currently crashes with a low-address-protection exception
if a user space process executes an instruction that tries to use the
linkage stack. Set the base-ASTE origin and the subspace-ASTE origin
of the dispatchable-unit-control-table to point to a dummy ASTE.
Set up control register 15 to point to an empty linkage stack with no
room left.
A user space process with a linkage stack instruction will still crash
but with a different exception which is correctly translated to a
segmentation fault instead of a kernel oops.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It was correctly set on mv78460 but not on mv78260, resulting in my
OpenBlocks AX3-4 retrieving only 3 of its 4 MAC addresses from the
boot loader.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Whilst the text segment for our VDSO is marked as PT_LOAD in the ELF
headers, it is mapped by the kernel and not actually subject to
demand-paging. ld doesn't realise this, and emits a p_align field of 64k
(the maximum supported page size), which conflicts with the load address
picked by the kernel on 4k systems, which will be 4k aligned. This
causes GDB to fail with "Failed to read a valid object file image from
memory" when attempting to load the VDSO.
This patch passes the -n option to ld, which prevents it from aligning
PT_LOAD segments to the maximum page size.
Cc: <stable@vger.kernel.org>
Reported-by: Kyle McMartin <kyle@redhat.com>
Acked-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Dumps created by kdump or zfcpdump can contain invalid memory holes when
dumping z/VM systems that have memory pressure.
For example:
# zgetdump -i /proc/vmcore.
Memory map:
0000000000000000 - 0000000000bfffff (12 MB)
0000000000e00000 - 00000000014fffff (7 MB)
000000000bd00000 - 00000000f3bfffff (3711 MB)
The memory detection function find_memory_chunks() issues tprot to
find valid memory chunks. In case of CMM it can happen that pages are
marked as unstable via set_page_unstable() in arch_free_page().
If z/VM has released that pages, tprot returns -EFAULT and indicates
a memory hole.
So fix this and switch off CMM in case of kdump or zfcpdump.
Cc: <stable@vger.kernel.org>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Wire up for MIPS the new sched_setattr and sched_getattr system calls
added in commit d50dde5a10 (sched: Add new scheduler syscalls to
support an extended scheduling parameters ABI) merged in v3.14-rc1.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6502/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With CONFIG_GPIOLIB=y gpios need to be requested before they can be
modified. Request the SD carddetect pins, and drop the SPI direction
setup, as the driver does that for us anyway. This gets rid of a
lot of WARN_ON()s triggered by GPIO core, and restores functionality
of the touschreen controller.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6497/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
During bootup in the 'probe_page_size_mask' these CR4 flags are
set in there. But for AP processors they are not set as we do not
use 'secondary_startup_64' which the baremetal kernels uses.
Instead do it in this function which we use in Xen PVH during our
startup for AP processors.
As such fix it up to make sure we have that flag set.
Signed-off-by: Mukesh Rathor <mukesh.rathor@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
arch/arm/mach-tegra/pm.c, kernel/power/console.c and mm/vmpressure.c
were somehow getting slab.h indirectly through cgroup.h which in turn
was getting it indirectly through xattr.h. A scheduled cgroup change
drops xattr.h inclusion from cgroup.h and breaks compilation of these
three files. Add explicit slab.h includes to the three files.
A pending cgroup patch depends on this change and it'd be great if
this can be routed through cgroup/for-3.14-fixes branch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-tegra@vger.kernel.org
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: cgroups@vger.kernel.org
This reverts commit 08ece5bb23.
As it breaks ARM builds and needs more attention
on the ARM side.
Acked-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The selection of HAVE_ARM_TWD for OMAP and shmobile depend on LOCAL_TIMER
which no longer exists. They should depend on SMP instead.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Move the DMA_OF selection to the DMA driver to fix kconfig warning:
warning: (ARCH_MOXART) selects DMA_OF which has unmet direct dependencies (DMADEVICES && OF)
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit "ARM: hisi: don't select SMP" introduced a kconfig warning:
warning: (ARCH_HI3xxx) selects HAVE_ARM_TWD which has unmet direct dependencies (SMP)
Fix HAVE_ARM_TWD to depend on SMP.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for the flexible mmap memory layout (as described in
http://lwn.net/Articles/91829). This is especially very interesting on
parisc since we currently only support 32bit userspace (even with a
64bit Linux kernel).
Signed-off-by: Helge Deller <deller@gmx.de>
On Linux, only parisc uses a different value for EWOULDBLOCK which
causes a lot of troubles for applications not checking for both values.
Since the hpux compat is long dead, make EWOULDBLOCK behave the same as
all other architectures.
Signed-off-by: Guy Martin <gmsoft@tuxicoman.be>
Signed-off-by: Helge Deller <deller@gmx.de>
The stat.h header file is exported to userspace. Some userspace
applications failed to compile due to missing/unknown types, so we
better convert it to use native types only (like it's done on other
architectures too).
Signed-off-by: Helge Deller <deller@gmx.de>
This commit:
f8dae00684d678afa13041ef170cecfd1297ed40: parisc: Ensure full cache coherency for kmap/kunmap
caused negative caching side-effects, e.g. hanging processes with expect and
too many inequivalent alias messages from flush_dcache_page() on Debian 5 systems.
This patch now partly reverts it and has been in production use on our debian buildd
makeservers since a week without any major problems.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Helge Deller <deller@gmx.de>
Here's a set of patches for (hopefully) -rc1. Some of them are fixes,
but a good number of them also do things such as enable new drivers in
the defconfigs for platforms that have such devices, increases coverage
of the multiplatform defconfig and some DTS changes that plumbs up some
of the devices that now have bindings and driver support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJS7VYsAAoJEIwa5zzehBx3FKIQAIVIkjlKAtvRpg+P/BYWigXq
6jG2xuBhwf1Yciu70ttvfRnR9bGJc+0o5w/qjr7ARSFp7GkDlWXtIwj+1EwGSEES
hB/f2GcBfNLJOI0rHvvudz+7HlpiyfB6iMj3U25hnpShrSTxbOHDC6pU6pYjUzBy
T1AYTmfa0vwuy9TNodOr4dVYlbJc3YA0V2sBTusXDFwm03XTdCd7E7RJIr/MRDEN
96PtaNrfstmxeTjN0NBuL2IdsZNR2mn/cgWTL1lVqVE8+z7QyvmPDqmWD5iCVQaM
+6mJbXL4jzM1CyB8Qf89sNtTaFVjwbgvbtuljPv/7q/jhf2rvixaMzywCv28FjB+
uJCaLh1r/HiR61tlw0yX3ixPdKFJqyWV9vF5+uuwmEQCCPpFWGzTcNaZ7NRiYzEt
yqt1ZRDhEAli8iHt96LxMwLIklaDGvuxLtHsv4a5djEoaO/yqRTNZXDjwIsIzkpD
N8vUwPf7Pnw+3/5iGVTQdZaPzmrNjqTOLwz0s7ys2avVsRsNNi68hMuIj+qrNlzu
/tJhhh0u9SONRM3c6D9mtrZPD7Gs8QgMbT9TyZ2/ILQKuo4wO9F1GDN93MjZI5oq
1rX/QUeYItWQamzHGmI8ZlAx4YlsxxB90eJ8CaG2F8sVtumklrFRb43Vf9NRsyo/
XDrjoS/cdi7PAO0wemkg
=ymAC
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's a set of patches for (hopefully) -rc1. Some of them are fixes,
but a good number of them also do things such as enable new drivers in
the defconfigs for platforms that have such devices, increases
coverage of the multiplatform defconfig and some DTS changes that
plumbs up some of the devices that now have bindings and driver
support.
The commit dates are recent; we've mostly collected these fixes in the
last few days but I also had to rebuild the branch yesterday to sort
out some internal conflicts which reset the timestamps. The changes
should have been tested by each platform maintainer already (and few
of them have cross-platform impact) so I'm personally not too
concerned by it at this time"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
ARM: multi_v7_defconfig: remove redundant entries and re-enable TI_EDMA
ARM: multi_v7_defconfig: add mvebu drivers
clocksource: kona: Add basic use of external clock
drivers: bus: fix CCI driver kcalloc call parameters swap
ARM: dts: bcm28155-ap: Fix Card Detection GPIO
ARM: multi_v7_defconfig: Select CONFIG_AT803X_PHY
ARM: keystone: config: fix build warning when CONFIG_DMADEVICES is not set
MAINTAINERS: ARM: SiRF: use regex patterns to involve all SiRF drivers
ARM: dts: zynq: Add SDHCI nodes
ARM: hisi: don't select SMP
ARM: tegra: rebuild tegra_defconfig to add DEBUG_FS
ARM: multi_v7: copy most options from tegra_defconfig
ARM: iop32x: fix power off handling for the EM7210 board
ARM: integrator: restore static map on the CP
ARM: msm_defconfig: Enable MSM clock drivers
ARM: dts: msm: Add clock controller nodes and hook into uart
ARM: OMAP4+: move errata initialization to omap4_pm_init_early
ARM: OMAP4460: cpuidle: Extend PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD on cpuidle
ARM: mvebu: fix compilation warning on Armada 370 (i.e. non-SMP)
ARM: shmobile: r8a7790.dtsi: ficx i2c[0-3] clock reference
...
With DISCONTIGMEM, the mapping between a pfn and its owning node is
initialized using data provided by the BIOS. However, the initialization
may fail if the extents are not aligned to section boundary (64M).
The symptom of this bug is an early boot failure in pfn_to_page(),
as it tries to access NODE_DATA(__nid) using index from an unitialized
element of the physnode_map[] array.
While the bug is always present, it is more likely to be hit in kdump
kernels on large machines, because:
1. The memory map for a kdump kernel is specified as exactmap, and
exactmap is more likely to be unaligned.
2. Large reservations are more likely to span across a 64M boundary.
[ hpa: fixed incorrect use of "pfn" instead of "start" ]
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Link: http://lkml.kernel.org/r/20140201133019.32e56f86@hananiah.suse.cz
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
With commit d8d14bd09c ("fs/compat: fix lookup_dcookie() parameter
handling") I changed the type of the len parameter of the
lookup_dcookie() syscall.
However I missed that there was still a stale declaration in
arch/tile/.. which now causes a compile error on tile:
In file included from fs/dcookies.c:28:0:
include/linux/compat.h:425:17: error: conflicting types for 'compat_sys_lookup_dcookie'
fs/dcookies.c:207:1: error: conflicting types for 'compat_sys_lookup_dcookie'
Simply remove the declaration in the tile architecture, which is only a
leftover from before the different compat lookup_dcookie() versions have
been merged. The correct declaration is now in include/linux/compat.h
The build error was reported by Fenguang's build bot.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
TI_EDMA fell out of automatically selected options in the multi_v7
defconfig due to a select being removed from the davinci Kconfig entry. So
we need to re-enable explicitly to not regress some platforms.
The rest is just the result of running 'make multi_v7_defconfig + make
savedefconfig' to remove entries that are no longer needed due to changed
dependencies/selects or defaults.
Signed-off-by: Olof Johansson <olof@lixom.net>
Recent boot farm testing has highlighted some issues with mvebu and
multiplatform kernels. Increase the test coverage so we can discover
these issues earlier.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
The board schematic states that the "SD_CARD_DET_N gets pulled to GND
when card is inserted" so the polarity has been updated to active low.
Polarity is now specified with a GPIO define instead of a magic number.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Correct i2c clock references for r8a7790 (R-Car H2) SoC
The error was introduced in 72197ca7a1 ("ARM: shmobile: r8a7790:
Reference clocks") which is queued up for v3.14.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=UVOK
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-fixes2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Second Round of Renesas ARM Based SoC DT Fixes for v3.14
Correct i2c clock references for r8a7790 (R-Car H2) SoC
The error was introduced in 72197ca7a1 ("ARM: shmobile: r8a7790:
Reference clocks") which is queued up for v3.14.
* tag 'renesas-dt-fixes2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790.dtsi: ficx i2c[0-3] clock reference
Signed-off-by: Olof Johansson <olof@lixom.net>
Select CONFIG_AT803X_PHY so that we can boot hummingboard via NFS.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Drop automatic selection of TI_EDMA from Keystone Kconfig file,
as it produces build warning in case if CONFIG_DMADEVICES is not set:
warning: (ARCH_KEYSTONE) selects TI_EDMA which has unmet direct dependencies (DMADEVICES && (ARCH_DAVINCI || ARCH_OMAP || ARCH_KEYSTONE))
Instead enable TI EDMA support from defconfig.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
- allow building and booting DT and non-DT plat-orion SoCs
- catch proper return value for kirkwood_pm_init()
- properly check return of of_iomap to solve boot hangs (mirabox, others)
- remove a compile warning on Armada 370 with non-SMP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=mxq4
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-3.13-2' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for v3.13 (incremental #2)
- allow building and booting DT and non-DT plat-orion SoCs
- catch proper return value for kirkwood_pm_init()
- properly check return of of_iomap to solve boot hangs (mirabox, others)
- remove a compile warning on Armada 370 with non-SMP.
* tag 'mvebu-fixes-3.13-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: fix compilation warning on Armada 370 (i.e. non-SMP)
ARM: mvebu: Fix kernel hang in mvebu_soc_id_init() when of_iomap failed
ARM: kirkwood: kirkwood_pm_init() should return void
ARM: orion: provide C-style interrupt handler for MULTI_IRQ_HANDLER
Signed-off-by: Olof Johansson <olof@lixom.net>
Add nodes for the Arasan SDHCI controller to Zynq dts files.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
SMP is a user configurable option, not a hardware feature and should not
be selected.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
DEBUG_FS used to be selected by COMMON_CLK_DEBUG, which was enabled
by tegra_defconfig. However, this config option no longer exists, so
no longer selects DEBUG_FS, and nothing else selects it either. So,
"make tegra_defconfig" no longer enables DEBUG_FS in .config.
Rebuild tegra_defconfig on top of next-20140424, while manually
re-enabling DEBUG_FS.
Reasons for removed entries are:
- I2C_MUX: selected by MEDIA_SUBDRV_AUTOSELECT
- DRM_PANEL: selected by DRM_TEGRA
- NEW_LEDS: selected by many things; at least VT
- LEDS_CLASS: selected by many things; at least VT
- LEDS_TRIGGERS: selected by many things; at least VT
- COMMON_CLK_DEBUG: no longer exists
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
multi_v7_defconfig was missing a large number of options that were in
tegra_defconfig. This patch adds them. The changes fall into the
following categories:
* Enable more Tegra SoC options/drivers.
* Enable more drivers for Tegra boards.
* Enable more options that are useful for running distros.
The patch removes a few lines as well, simply because those options are
now selected by something else, and "make savedefconfig" removes them. I
verified that the options appear in .config after
"make multi_v7_defconfig".
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This board was missed when converting all the others to proper
abstracted GPIO handling. Fix it up the right way by requesting
and driving GPIO line 0 high through gpiolib to power off the
machine.
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 78d1632183 deleted the
static mappings of the core modules, but this static map is
still needed on the Integrator/CP (not the Integrator/AP).
Restore the static map on the Integrator/CP.
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This allows us to probe the clock controller devices and boot to a
serial console on all DT enabled MSM platforms.
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the necessary DT nodes to probe the clock controllers on MSM
devices as well as hook up the uart nodes to the clock
controllers. This should allow us to boot to a serial console on
all DT enabled MSM platforms.
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Move all OMAP4 PM errata initializations to centralized location in
omap4_pm_init_early. This allows for users to utilize the erratas
in various submodules as needed.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The same workaround as ff999b8a09
"ARM: OMAP4460: Workaround for ROM bug because of CA9 r2pX GIC ..."
need to be applied not only when system is booting, but when MPUSS hits
OSWR state through CPUIdle too. Without this WA the same issue is
reproduced now on boards PandaES and Tablet/Blaze with SOM OMAP4460
when CONFIG_CPU_IDLE is enabled.
After MPUSS has enterred OSWR and waken up:
- GIC distributor became disabled forever
- scheduling is not performed any more
Cc: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reported-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Introduction of PTE_WRITE to distinguish between writable but clean
and truly read-only pages
- FIQs enabling/disabling clean-up (they aren't used on arm64)
- CPU resume fix for the per-cpu offset restoring
- Code comment typos
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=tWas
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pyll ARM64 patches from Catalin Marinas:
- Build fix with DMA_CMA enabled
- Introduction of PTE_WRITE to distinguish between writable but clean
and truly read-only pages
- FIQs enabling/disabling clean-up (they aren't used on arm64)
- CPU resume fix for the per-cpu offset restoring
- Code comment typos
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: Introduce PTE_WRITE
arm64: mm: Remove PTE_BIT_FUNC macro
arm64: FIQs are unused
arm64: mm: fix the function name in comment of cpu_do_switch_mm
arm64: fix build error if DMA_CMA is enabled
arm64: kernel: fix per-cpu offset restore on resume
arm64: mm: fix the function name in comment of __flush_dcache_area
arm64: mm: use ubfm for dcache_line_size
Pull alpha updates from Matt Turner:
"A pair of changes for alpha. One fixes a networking regression, and
the second adds audit syscall support which will help in supporting
systemd"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
alpha: fix broken network checksum
alpha: Enable system-call auditing support.
Pull media updates from Mauro Carvalho Chehab:
- a new jpeg codec driver for Samsung Exynos (jpeg-hw-exynos4)
- a new dvb frontend for ds2103 chipset (m88ds2103)
- a new sensor driver for Samsung S5K5BAF UXGA (s5k5baf)
- new drivers for R-Car VSP1
- a new radio driver: radio-raremono
- a new tuner driver for ts2022 chipset (m88ts2022)
- the analog part of em28xx is now a separate module that only
load/runs if the device is not a pure digital TV device
- added a staging driver for bcm2048 radio devices
- the omap 2 video driver (omap24xx) was moved to staging. This driver
is for an old hardware and uses a deprecated Kernel internal API. If
nobody cares enough to fix it, it would be removed on a couple Kernel
releases
- the sn9c102 driver was moved to staging. This driver was replaced by
gspca, and disabled on some distros, as almost all devices are known
to work properly with gspca. It should be removed from kernel on a
couple Kernel releases
- lots of driver fixes, improvements and cleanups
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (421 commits)
[media] media: v4l2-dev: fix video device index assignment
[media] rc-core: reuse device numbers
[media] em28xx-cards: properly initialize the device bitmap
[media] Staging: media: Fix line length exceeding 80 characters in as102_drv.c
[media] Staging: media: Fix line length exceeding 80 characters in as102_fe.c
[media] Staging: media: Fix quoted string split across line in as102_fe.c
[media] media: st-rc: Add reset support
[media] m2m-deinterlace: fix allocated struct type
[media] radio-usb-si4713: fix sparse non static symbol warnings
[media] em28xx-audio: remove needless check before usb_free_coherent()
[media] au0828: Fix sparse non static symbol warning
Revert "[media] go7007-usb: only use go->dev after allocated"
[media] em28xx-audio: provide an error code when URB submit fails
[media] em28xx: fix check for audio only usb interfaces when changing the usb alternate setting
[media] em28xx: fix usb alternate setting for analog and digital video endpoints > 0
[media] em28xx: make 'em28xx_ctrl_ops' static
em28xx-alsa: Fix error patch for init/fini
[media] em28xx-audio: flush work at .fini
[media] drxk: remove the option to load firmware asynchronously
[media] em28xx: adjust period size at runtime
...
The patch 3ddc5b46a8 breaks networking on
alpha (there is a follow-up fix 5cfe8f1ba5,
but networking is still broken even with the second patch).
The patch 3ddc5b46a8 makes
csum_partial_copy_from_user check the pointer with access_ok. However,
csum_partial_copy_from_user is called also from csum_partial_copy_nocheck
and csum_partial_copy_nocheck is called on kernel pointers and it is
supposed not to check pointer validity.
This bug results in ssh session hangs if the system is loaded and bulk
data are printed to ssh terminal.
This patch fixes csum_partial_copy_nocheck to call set_fs(KERNEL_DS), so
that access_ok in csum_partial_copy_from_user accepts kernel-space
addresses.
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Pull core debug changes from Ingo Molnar:
"This contains mostly kernel debugging related updates:
- make hung_task detection more configurable to distros
- add final bits for x86 UV NMI debugging, with related KGDB changes
- update the mailing-list of MAINTAINERS entries I'm involved with"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hung_task: Display every hung task warning
sysctl: Add neg_one as a standard constraint
x86/uv/nmi, kgdb/kdb: Fix UV NMI handler when KDB not configured
x86/uv/nmi: Fix Sparse warnings
kgdb/kdb: Fix no KDB config problem
MAINTAINERS: Restore "L: linux-kernel@vger.kernel.org" entries
- Xen ARM couldn't use the new FIFO events
- Xen ARM couldn't use the SWIOTLB if compiled as 32-bit with 64-bit PCIe devices.
- Grant table were doing needless M2P operations.
- Ratchet down the self-balloon code so it won't OOM.
- Fix misplaced kfree in Xen PVH error code paths.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJS68IQAAoJEFjIrFwIi8fJAWgH/j4HStEey3rgGcqwIWSHkkap
+t55wsrT8Ylq6CzZjaUtCo3pB7HotW526x/0rA2pxVqHn/8oCN/1EtdrNtYm/umX
qOoda+db5NIjAEGVLWSLqGyokJQDrX/brXIWfYR300e9fnJi7yT/rFC4QHoZVUYl
5LME8XH/jE012vvYelNu6DbbodlRmVCT8hctJS+eB5ER2WmtD9Pkw4GybEXPVYJz
hE0Ts1DN91nKP2FGJb+mfB9UFT5X8i00akAK+Qc1R3sRnRh6eRoNV8dgyCnudKpO
UPEdiAZvgij+mzlgIYSz6nKH0U/VbvRsG3lc3i5Si3o+vR3CYPCkvzOGX2d0rjw=
=7cxW
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.14-rc0-late-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen bugfixes from Konrad Rzeszutek Wilk:
"Bug-fixes for the new features that were added during this cycle.
There are also two fixes for long-standing issues for which we have a
solution: grant-table operations extra work that was not needed
causing performance issues and the self balloon code was too
aggressive causing OOMs.
Details:
- Xen ARM couldn't use the new FIFO events
- Xen ARM couldn't use the SWIOTLB if compiled as 32-bit with 64-bit PCIe devices.
- Grant table were doing needless M2P operations.
- Ratchet down the self-balloon code so it won't OOM.
- Fix misplaced kfree in Xen PVH error code paths"
* tag 'stable/for-linus-3.14-rc0-late-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pvh: Fix misplaced kfree from xlated_setup_gnttab_pages
drivers: xen: deaggressive selfballoon driver
xen/grant-table: Avoid m2p_override during mapping
xen/gnttab: Use phys_addr_t to describe the grant frame base address
xen: swiotlb: handle sizeof(dma_addr_t) != sizeof(phys_addr_t)
arm/xen: Initialize event channels earlier
two s390 guest features that need some handling in the host,
and all the PPC changes. The PPC changes include support for
little-endian guests and enablement for new POWER8 features.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABAgAGBQJS6UF5AAoJEBvWZb6bTYby55kP/AgTJnyu7avN653/2aSHkjkx
KgYSMYhZPIFoY5LyZuNetXaoXFRvCykux1VYSZ6V6s35h2PZ+hdJNbHGjFYKPGTq
FQ92xQVNuWCAPxmFCjDNuDV/0BauG5y08/Orh/jpjz+GAfH43LruUQGbtXUuyJ8u
vf+yTHniU5gguqsAmodqjHUgbf+GoPJ1j7hmRoWwt8IWm7Ns3v/IK4l0p6G0h26a
RjE6aK+Tm208Yr5hD/dRAqeTbBNt3c4xub+QPsKoiEMaZBSuAOiux7D3Kx+If1gp
WsmqEQxoymihVtkZhUFO9ONLJepvmG2QwJVVyMSUW9iqxX9rraXsvVyVMwcQAhog
JuOAYxBftH07xu6Fs4eym5KvCFghM+EaJvxxt+kgnvdD4htK1+eK5trntc2zygSi
/qGiIrkqjXpkskW8kujLayF0eAU3CrZvFWveEPBfFgYiOGX/2wzJCtSm/bt9Jo0M
v60qgNFK3LNqAyeEfnm9VtlwGr6ZgsAB6DHNPX4fM5s2IBjL+qloXk/e/+aVKkW0
I3yeRdy/ExhLAab6w81JtMeR7G3YS0UNuAEVvcoxzNb5wIBY8qnpfUzTKyMxQR94
64EVpxWEYO1s55eCCyMujWrSvc+YAwhJcWHGKgC4K7mxxLD3FVyQXX6YZvgRozMX
HjQju+DToj9CskyrFlRL
=yd0Z
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more KVM updates from Paolo Bonzini:
"Second batch of KVM updates. Some minor x86 fixes, two s390 guest
features that need some handling in the host, and all the PPC changes.
The PPC changes include support for little-endian guests and
enablement for new POWER8 features"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (45 commits)
x86, kvm: correctly access the KVM_CPUID_FEATURES leaf at 0x40000101
x86, kvm: cache the base of the KVM cpuid leaves
kvm: x86: move KVM_CAP_HYPERV_TIME outside #ifdef
KVM: PPC: Book3S PR: Cope with doorbell interrupts
KVM: PPC: Book3S HV: Add software abort codes for transactional memory
KVM: PPC: Book3S HV: Add new state for transactional memory
powerpc/Kconfig: Make TM select VSX and VMX
KVM: PPC: Book3S HV: Basic little-endian guest support
KVM: PPC: Book3S HV: Add support for DABRX register on POWER7
KVM: PPC: Book3S HV: Prepare for host using hypervisor doorbells
KVM: PPC: Book3S HV: Handle new LPCR bits on POWER8
KVM: PPC: Book3S HV: Handle guest using doorbells for IPIs
KVM: PPC: Book3S HV: Consolidate code that checks reason for wake from nap
KVM: PPC: Book3S HV: Implement architecture compatibility modes for POWER8
KVM: PPC: Book3S HV: Add handler for HV facility unavailable
KVM: PPC: Book3S HV: Flush the correct number of TLB sets on POWER8
KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs
KVM: PPC: Book3S HV: Align physical and virtual CPU thread numbers
KVM: PPC: Book3S HV: Don't set DABR on POWER8
kvm/ppc: IRQ disabling cleanup
...
Passing a freed 'pages' to free_xenballooned_pages will end badly
on kernels with slub debug enabled.
This looks out of place between the rc assign and the check, but
we do want to kfree pages regardless of which path we take.
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The grant mapping API does m2p_override unnecessarily: only gntdev needs it,
for blkback and future netback patches it just cause a lock contention, as
those pages never go to userspace. Therefore this series does the following:
- the original functions were renamed to __gnttab_[un]map_refs, with a new
parameter m2p_override
- based on m2p_override either they follow the original behaviour, or just set
the private flag and call set_phys_to_machine
- gnttab_[un]map_refs are now a wrapper to call __gnttab_[un]map_refs with
m2p_override false
- a new function gnttab_[un]map_refs_userspace provides the old behaviour
It also removes a stray space from page.h and change ret to 0 if
XENFEAT_auto_translated_physmap, as that is the only possible return value
there.
v2:
- move the storing of the old mfn in page->index to gnttab_map_refs
- move the function header update to a separate patch
v3:
- a new approach to retain old behaviour where it needed
- squash the patches into one
v4:
- move out the common bits from m2p* functions, and pass pfn/mfn as parameter
- clear page->private before doing anything with the page, so m2p_find_override
won't race with this
v5:
- change return value handling in __gnttab_[un]map_refs
- remove a stray space in page.h
- add detail why ret = 0 now at some places
v6:
- don't pass pfn to m2p* functions, just get it locally
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Suggested-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
We have the following means for encoding writable or dirty ptes:
PTE_DIRTY PTE_RDONLY
!pte_dirty && !pte_write 0 1
!pte_dirty && pte_write 0 1
pte_dirty && !pte_write 1 1
pte_dirty && pte_write 1 0
So we can't distinguish between writable clean ptes and read only
ptes. This can cause problems with ptes being incorrectly flagged as
read only when they are writable but not dirty.
This patch introduces a new software bit PTE_WRITE which allows us to
correctly identify writable ptes. PTE_RDONLY is now only clear for
valid ptes where a page is both writable and dirty.
Signed-off-by: Steve Capper <steve.capper@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Expand out the pte manipulation functions. This makes our life easier
when using things like tags and cscope.
Signed-off-by: Steve Capper <steve.capper@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Merge misc fixes from Andrew Morton:
"A few hotfixes and various leftovers which were awaiting other merges.
Mainly movement of zram into mm/"
* emailed patches fron Andrew Morton <akpm@linux-foundation.org>: (25 commits)
memcg: fix mutex not unlocked on memcg_create_kmem_cache fail path
Documentation/filesystems/vfs.txt: update file_operations documentation
mm, oom: base root bonus on current usage
mm: don't lose the SOFT_DIRTY flag on mprotect
mm/slub.c: fix page->_count corruption (again)
mm/mempolicy.c: fix mempolicy printing in numa_maps
zram: remove zram->lock in read path and change it with mutex
zram: remove workqueue for freeing removed pending slot
zram: introduce zram->tb_lock
zram: use atomic operation for stat
zram: remove unnecessary free
zram: delay pending free request in read path
zram: fix race between reset and flushing pending work
zsmalloc: add maintainers
zram: add zram maintainers
zsmalloc: add copyright
zram: add copyright
zram: remove old private project comment
zram: promote zram from staging
zsmalloc: move it under mm
...
Pull x86 asmlinkage (LTO) changes from Peter Anvin:
"This patchset adds more infrastructure for link time optimization
(LTO).
This patchset was pulled into my tree late because of a
miscommunication (part of the patchset was picked up by other
maintainers). However, the patchset is strictly build-related and
seems to be okay in testing"
* 'x86-asmlinkage-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, asmlinkage, xen: Fix type of NMI
x86, asmlinkage, xen, kvm: Make {xen,kvm}_lock_spinning global and visible
x86: Use inline assembler instead of global register variable to get sp
x86, asmlinkage, paravirt: Make paravirt thunks global
x86, asmlinkage, paravirt: Don't rely on local assembler labels
x86, asmlinkage, lguest: Fix C functions used by inline assembler
Pull x86 build bits from Peter Anvin:
"Various build-related minor bits.
Most of this is work by David Woodhouse to be able to compile the
early boot code with clang/llvm; we have also managed to push an
actual -m16 option into gcc 4.9 so this makes us use that option if
available instead of hacking it.
The balance is a patch from Michael Davidson to the relocs program to
help manual debugging.
None of these should change the actual compiled binary with currently
released compilers"
* 'x86-build-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, build: Build 16-bit code with -m16 where possible
x86, boot: Fix word-size assumptions in has_eflag() inline asm
x86, boot: Use __attribute__((used)) to ensure videocard structs are emitted
x86: Remove duplication of 16-bit CFLAGS
x86, relocs: Add manual debug mode
These are changes that arrived a little late but were considered
self-contained enough to still go in for v3.14.
They are all device tree updtes this time around, and mainly for
Broadcom SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=tEa/
-----END PGP SIGNATURE-----
Merge tag 'late-dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late changes from Kevin Hilman:
"These are changes that arrived a little late but were considered
self-contained enough to still go in for v3.14.
They are all device tree updtes this time around, and mainly for
Broadcom SoCs"
* tag 'late-dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: moxart: move fixed rate clock child node to board level dts
clk: bcm281xx: define kona clock binding
ARM: dts: add usb udc support to bcm281xx
ARM: dts: Specify clocks for timer on bcm11351
Documentation: dt: kona-timer: Add clocks property
ARM: dts: Specify clocks for SDHCIs on bcm11351
Documentation: dt: kona-sdhci: Add clocks property
ARM: dts: Specify clocks for UARTs on bcm11351
ARM: dts: bcm281xx: Add i2c busses
ARM: dts: Declare clocks as fixed on bcm11351
ARM: dts: bcm28155-ap: Enable all the i2c busses
Pull MIPS updates from Ralf Baechle:
"The most notable new addition inside this pull request is the support
for MIPS's latest and greatest core called "inter/proAptiv". The
patch series describes this core as follows.
"The interAptiv is a power-efficient multi-core microprocessor
for use in system-on-chip (SoC) applications. The interAptiv combines
a multi-threading pipeline with a coherence manager to deliver improved
computational throughput and power efficiency. The interAptiv can
contain one to four MIPS32R3 interAptiv cores, system level
coherence manager with L2 cache, optional coherent I/O port,
and optional floating point unit."
The platform specific patches touch all 3 Broadcom families. It adds
support for the new Broadcom/Netlogix XLP9xx Soc, building a common
BCM63XX SMP kernel for all BCM63XX SoCs regardless of core type/count
and full gpio button/led descriptions for BCM47xx.
The rest of the series are cleanups and bug fixes that are MIPS
generic and consist largely of changes that Imgtec/MIPS had published
in their linux-mti-3.10.git stable tree. Random other cleanups and
patches preparing code to be merged in 3.15"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (139 commits)
mips: select ARCH_MIGHT_HAVE_PC_SERIO
mips: delete non-required instances of include <linux/init.h>
MIPS: KVM: remove shadow_tlb code
MIPS: KVM: use common EHINV aware UNIQUE_ENTRYHI
mips/ide: flush dcache also if icache does not snoop dcache
MIPS: BCM47XX: fix position of cpu_wait disabling
MIPS: BCM63XX: select correct MIPS_L1_CACHE_SHIFT value
MIPS: update MIPS_L1_CACHE_SHIFT based on MIPS_L1_CACHE_SHIFT_<N>
MIPS: introduce MIPS_L1_CACHE_SHIFT_<N>
MIPS: ZBOOT: gather string functions into string.c
arch/mips/pci: don't check resource with devm_ioremap_resource
arch/mips/lantiq/xway: don't check resource with devm_ioremap_resource
bcma: gpio: don't cast u32 to unsigned long
ssb: gpio: add own IRQ domain
MIPS: BCM47XX: fix sparse warnings in board.c
MIPS: BCM47XX: add board detection for Linksys WRT54GS V1
MIPS: BCM47XX: fix detection for some boards
MIPS: BCM47XX: Enable buttons support on SSB
MIPS: BCM47XX: Convert WNDR4500 to new syntax
MIPS: BCM47XX: Use "timer" trigger for status LEDs
...
The interesting change here is a rework of the OpenRISC signal handling
to make it more like other architectures in the hopes that this
makes it easier for others to comment on and understand. This
rework fixes some real bugs, like the fact that syscall restart
did not work reliably.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAlLqR+0ACgkQ70gcjN2673PA4ACePPK0tWp0swxAezjwq1KzXfVi
xMcAn3Y/z7PXximluzeThTeqjeSz/wJ4
=DDIb
-----END PGP SIGNATURE-----
Merge tag 'for-3.14' of git://openrisc.net/~jonas/linux
Pull OpenRISC updates from Jonas Bonn:
"The interesting change here is a rework of the OpenRISC signal
handling to make it more like other architectures in the hopes that
this makes it easier for others to comment on and understand. This
rework fixes some real bugs, like the fact that syscall restart did
not work reliably"
* tag 'for-3.14' of git://openrisc.net/~jonas/linux:
openrisc: Use get_signal() signal_setup_done()
openrisc: Rework signal handling
Pull more powerpc bits from Ben Herrenschmidt:
"Here are a few more powerpc bits for this merge window. The bulk is
made of two pull requests from Scott and Anatolij that I had missed
previously (they arrived while I was away). Since both their branches
are in -next independently, and the content has been around for a
little while, they can still go in.
The rest is mostly bug and regression fixes, a small series of
cleanups to our pseries cpuidle code (including moving it to the right
place), and one new cpuidle bakend for the powernv platform. I also
wired up the new sched_attr syscalls"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (37 commits)
powerpc: Wire up sched_setattr and sched_getattr syscalls
powerpc/hugetlb: Replace __get_cpu_var with get_cpu_var
powerpc: Make sure "cache" directory is removed when offlining cpu
powerpc/mm: Fix mmap errno when MAP_FIXED is set and mapping exceeds the allowed address space
powerpc/powernv/cpuidle: Back-end cpuidle driver for powernv platform.
powerpc/pseries/cpuidle: smt-snooze-delay cleanup.
powerpc/pseries/cpuidle: Remove MAX_IDLE_STATE macro.
powerpc/pseries/cpuidle: Make cpuidle-pseries backend driver a non-module.
powerpc/pseries/cpuidle: Use cpuidle_register() for initialisation.
powerpc/pseries/cpuidle: Move processor_idle.c to drivers/cpuidle.
powerpc: Fix 32-bit frames for signals delivered when transactional
powerpc/iommu: Fix initialisation of DART iommu table
powerpc/numa: Fix decimal permissions
powerpc/mm: Fix compile error of pgtable-ppc64.h
powerpc: Fix hw breakpoints on !HAVE_HW_BREAKPOINT configurations
clk: corenet: Adds the clock binding
powerpc/booke64: Guard e6500 tlb handler with CONFIG_PPC_FSL_BOOK3E
powerpc/512x: dts: add MPC5125 clock specs
powerpc/512x: clk: support MPC5121/5123/5125 SoC variants
powerpc/512x: clk: enforce even SDHC divider values
...
Pull __TIME__/__DATE__ removal from Michal Marek:
"This series by Josh finishes the removal of __DATE__ and __TIME__ from
the kernel. The last patch adds -Werror=date-time to KBUILD_CFLAGS to
stop these from reappearing.
Part of the series went through Greg's trees during this merge window,
which is why this pull request is not based on v3.13-rc1"
* 'drop-time' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
Makefile: Build with -Werror=date-time if the compiler supports it
x86: math-emu: Drop already-disabled print of build date
net: wireless: brcm80211: Drop debug version with build date/time
mtd: denali: Drop print of build date/time
Pull kbuild changes from Michal Marek:
- fix make -s detection with make-4.0
- fix for scripts/setlocalversion when the kernel repository is a
submodule
- do not hardcode ';' in macros that expand to assembler code, as some
architectures' assemblers use a different character for newline
- Fix passing --gdwarf-2 to the assembler
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
frv: Remove redundant debugging info flag
mn10300: Remove redundant debugging info flag
kbuild: Fix debugging info generation for .S files
arch: use ASM_NL instead of ';' for assembler new line character in the macro
kbuild: Fix silent builds with make-4
Fix detectition of kernel git repository in setlocalversion script [take #2]
The SOFT_DIRTY bit shows that the content of memory was changed after a
defined point in the past. mprotect() doesn't change the content of
memory, so it must not change the SOFT_DIRTY bit.
This bug causes a malfunction: on the first iteration all pages are
dumped. On other iterations only pages with the SOFT_DIRTY bit are
dumped. So if the SOFT_DIRTY bit is cleared from a page by mistake, the
page is not dumped and its content will be restored incorrectly.
This patch does nothing with _PAGE_SWP_SOFT_DIRTY, becase pte_modify()
is called only for present pages.
Fixes commit 0f8975ec4d ("mm: soft-dirty bits for user memory changes
tracking").
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Further discussion here: http://marc.info/?l=linux-kernel&m=139073901101034&w=2
kbuild, 0day kernel build service, outputs the warning:
arch/x86/kernel/irq.c:333:1: warning: the frame size of 2056 bytes
is larger than 2048 bytes [-Wframe-larger-than=]
because check_irq_vectors_for_cpu_disable() allocates two cpumasks on the
stack. Fix this by moving the two cpumasks to a global file context.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Tested-by: David Rientjes <rientjes@google.com>
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1390915331-27375-1-git-send-email-prarit@redhat.com
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Cc: Yang Zhang <yang.z.zhang@Intel.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Janet Morgan <janet.morgan@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Ruiv Wang <ruiv.wang@gmail.com>
Cc: Gong Chen <gong.chen@linux.intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Pull core block IO changes from Jens Axboe:
"The major piece in here is the immutable bio_ve series from Kent, the
rest is fairly minor. It was supposed to go in last round, but
various issues pushed it to this release instead. The pull request
contains:
- Various smaller blk-mq fixes from different folks. Nothing major
here, just minor fixes and cleanups.
- Fix for a memory leak in the error path in the block ioctl code
from Christian Engelmayer.
- Header export fix from CaiZhiyong.
- Finally the immutable biovec changes from Kent Overstreet. This
enables some nice future work on making arbitrarily sized bios
possible, and splitting more efficient. Related fixes to immutable
bio_vecs:
- dm-cache immutable fixup from Mike Snitzer.
- btrfs immutable fixup from Muthu Kumar.
- bio-integrity fix from Nic Bellinger, which is also going to stable"
* 'for-3.14/core' of git://git.kernel.dk/linux-block: (44 commits)
xtensa: fixup simdisk driver to work with immutable bio_vecs
block/blk-mq-cpu.c: use hotcpu_notifier()
blk-mq: for_each_* macro correctness
block: Fix memory leak in rw_copy_check_uvector() handling
bio-integrity: Fix bio_integrity_verify segment start bug
block: remove unrelated header files and export symbol
blk-mq: uses page->list incorrectly
blk-mq: use __smp_call_function_single directly
btrfs: fix missing increment of bi_remaining
Revert "block: Warn and free bio if bi_end_io is not set"
block: Warn and free bio if bi_end_io is not set
blk-mq: fix initializing request's start time
block: blk-mq: don't export blk_mq_free_queue()
block: blk-mq: make blk_sync_queue support mq
block: blk-mq: support draining mq queue
dm cache: increment bi_remaining when bi_end_io is restored
block: fixup for generic bio chaining
block: Really silence spurious compiler warnings
block: Silence spurious compiler warnings
block: Kill bio_pair_split()
...
Both clang 3.5 and GCC 4.9 will support this (as of r199754 and r207196
respectively). Both have been tested to produce booting kernels when the
16-bit code is built with -m16. (Modulo LLVM PR3997, at least.)
[ hpa: folded test for -m16 into M16_CFLAGS ]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Link: http://lkml.kernel.org/r/1390997807.20153.133.camel@i7.infradead.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Commit dd78b97367 ("x86, boot: Move CPU
flags out of cpucheck") introduced ambiguous inline asm in the
has_eflag() function. In 16-bit mode want the instruction to be
'pushfl', but we just say 'pushf' and hope the compiler does what we
wanted.
When building with 'clang -m16', it won't, because clang doesn't use
the horrid '.code16gcc' hack that even 'gcc -m16' uses internally.
Say what we mean and don't make the compiler make assumptions.
[ hpa: ideally we would be able to use the gcc %zN construct here, but
that is broken for 64-bit integers in gcc < 4.5.
The code with plain "pushf/popf" is fine for 32- or 64-bit mode, but
not for 16-bit mode; in 16-bit mode those are 16-bit instructions in
.code16 mode, and 32-bit instructions in .code16gcc mode. ]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Link: http://lkml.kernel.org/r/1391079628.26079.82.camel@shinybook.infradead.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
So any FIQ handling is superfluous at the moment. The functions to
disable/enable FIQs is kept around if ever someone needs them in the
future, but existing calling sites including arch_cpu_idle_prepare()
may go for now.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In s390 des and 3des ctr mode there is one preallocated page
used to speed up the en/decryption. This page is not protected
against concurrent usage and thus there is a potential of data
corruption with multiple threads.
The fix introduces locking/unlocking the ctr page and a slower
fallback solution at concurrency situations.
Cc: stable@vger.kernel.org
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pekon Gupta