If frequency is throttled due to OCC reset then cpus will be in Psafe
frequency, so restore the frequency on all cpus to policy->cur when
OCCs are active again. And if frequency is throttled due to Pmax
capping then restore the frequency of all the cpus in the chip on
unthrottling.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On a reset cycle of OCC, although the system retires from safe
frequency state the local pstate is not restored to Pmin or last
requested pstate. Now if the cpufreq governor initiates a pstate
change, the local pstate will be in Psafe and we will be reporting a
false positive when we are not throttled.
So in powernv_cpufreq_throttle_check() remove the condition which
checks if local pstate is less than Pmin while checking for Psafe
frequency. If the cpus are forced to Psafe then PMSR.psafe_mode_active
bit will be set. So, when OCCs become active this bit will be cleared.
Let us just rely on this bit for reporting throttling.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Re-evaluate the chip's throttled state on recieving OCC_THROTTLE
notification by executing *throttle_check() on any one of the cpu on
the chip. This is a sanity check to verify if we were indeed
throttled/unthrottled after receiving OCC_THROTTLE notification.
We cannot call *throttle_check() directly from the notification
handler because we could be handling chip1's notification in chip2. So
initiate an smp_call to execute *throttle_check(). We are irq-disabled
in the notification handler, so use a worker thread to smp_call
throttle_check() on any of the cpu in the chipmask.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
OCC is an On-Chip-Controller which takes care of power and thermal
safety of the chip. During runtime due to power failure or
overtemperature the OCC may throttle the frequencies of the CPUs to
remain within the power budget.
We want the cpufreq driver to be aware of such situations to be able
to report the reason to the user. We register to opal_message_notifier
to receive OCC messages from opal.
powernv_cpufreq_throttle_check() reports any frequency throttling and
this patch will report the reason or event that caused throttling. We
can be throttled if OCC is reset or OCC limits Pmax due to power or
thermal reasons. We are also notified of unthrottling after an OCC
reset or if OCC restores Pmax on the chip.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The On-Chip-Controller(OCC) can throttle cpu frequency by reducing the
max allowed frequency for that chip if the chip exceeds its power or
temperature limits. As Pmax capping is a chip level condition report
this throttling behavior at chip level and also do not set the global
'throttled' on Pmax capping instead set the per-chip throttled
variable. Report unthrottling if Pmax is restored after throttling.
This patch adds a structure to store chip id and throttled state of
the chip.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Change cpufreq_policy_alloc() to take a CPU number instead of a CPU
device pointer as its argument, as it is the only function called by
cpufreq_add_dev() taking a device pointer argument at this point.
That will allow us to split the CPU online part from cpufreq_add_dev()
more cleanly going forward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The related_cpus mask includes CPUs whose cpufreq_cpu_data per-CPU
pointers have been set the the given policy. Since those pointers
are only set at the policy creation time and unset when the policy
is deleted, the related_cpus should not be updated between those
two operations.
For this reason, avoid updating it whenever the first of the
"related" CPUs goes online.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The dev argument of cpufreq_add_policy_cpu() and
cpufreq_add_dev_interface() is not used by any of them,
so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The leftover out_release_rwsem label in cpufreq_add_dev() is not
necessary any more and confusing, so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Notice that when cpufreq_policy_restore() is called, its per-CPU
cpufreq_cpu_data variable has been already dereferenced and if that
variable is not NULL, the policy local pointer in cpufreq_add_dev()
contains its value.
Therefore it is not necessary to dereference it again and the
policy pointer can be used directly. Moreover, if that pointer
is not NULL, the policy is inactive (or the previous check would
have made us return from cpufreq_add_dev()) so the restoration
code from cpufreq_policy_restore() can be moved to that point
in cpufreq_add_dev().
Do that and drop cpufreq_policy_restore().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Since __cpufreq_remove_dev_prepare() and __cpufreq_remove_dev_finish()
are about CPU offline rather than about CPU removal, rename them to
cpufreq_offline_prepare() and cpufreq_offline_finish(), respectively.
Also change their argument from a struct device pointer to a CPU
number, because they use the CPU number only internally anyway
and make them void as their return values are ignored.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
After commit 87549141d5 (cpufreq: Stop migrating sysfs files on
hotplug) there is a problem with CPUs that share cpufreq policy
objects with other CPUs and are initially offline.
Say CPU1 shares a policy with CPU0 which is online and is registered
first. As part of the registration process, cpufreq_add_dev() is
called for it. It creates the policy object and a symbolic link
to it from the CPU1's sysfs directory. If CPU1 is registered
subsequently and it is offline at that time, cpufreq_add_dev() will
attempt to create a symbolic link to the policy object for it, but
that link is present already, so a warning about that will be
triggered.
To avoid that warning, make cpufreq use an additional CPU mask
containing related CPUs that are actually present for each policy
object. That mask is initialized when the policy object is populated
after its creation (for the first online CPU using it) and it includes
CPUs from the "policy CPUs" mask returned by the cpufreq driver's
->init() callback that are physically present at that time. Symbolic
links to the policy are created only for the CPUs in that mask.
If cpufreq_add_dev() is invoked for an offline CPU, it checks the
new mask and only creates the symlink if the CPU was not in it (the
CPU is added to the mask at the same time).
In turn, cpufreq_remove_dev() drops the given CPU from the new mask,
removes its symlink to the policy object and returns, unless it is
the CPU owning the policy object. In that case, the policy object
is moved to a new CPU's sysfs directory or deleted if the CPU being
removed was the last user of the policy.
While at it, notice that cpufreq_remove_dev() can't fail, because
its return value is ignored, so make it ignore return values from
__cpufreq_remove_dev_prepare() and __cpufreq_remove_dev_finish()
and prevent these functions from aborting on errors returned by
__cpufreq_governor(). Also drop the now unused sif argument from
them.
Fixes: 87549141d5 (cpufreq: Stop migrating sysfs files on hotplug)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reported-and-tested-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Scaling for Knights Landing is same as the default scaling (100000).
When Knigts Landing support was added to the pstate driver, this
parameter was omitted resulting in a kernel panic during boot.
Fixes: b34ef932d7 (intel_pstate: Knights Landing support)
Reported-by: Yasuaki Ishimatsu <yishimat@redhat.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Lukasz Anaczkowski <lukasz.anaczkowski@intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Cc: 4.1+ <stable@vger.kernel.org> # 4.1+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_rwsem was introduced in commit 6eed9404ab ("cpufreq: Use
rwsem for protecting critical sections) in order to replace
try_module_get() on the cpu-freq driver. That try_module_get() worked
well until the refcount was so heavily used that module removal became
more or less impossible.
Though when looking at the various (undocumented) protection
mechanisms in that code, the randomly sprinkeled around cpufreq_rwsem
locking sites are superfluous.
The policy, which is acquired in cpufreq_cpu_get() and released in
cpufreq_cpu_put() is sufficiently protected already.
cpufreq_cpu_get(cpu)
/* Protects against concurrent driver removal */
read_lock_irqsave(&cpufreq_driver_lock, flags);
policy = per_cpu(cpufreq_cpu_data, cpu);
kobject_get(&policy->kobj);
read_unlock_irqrestore(&cpufreq_driver_lock, flags);
The reference on the policy serializes versus module unload already:
cpufreq_unregister_driver()
subsys_interface_unregister()
__cpufreq_remove_dev_finish()
per_cpu(cpufreq_cpu_data) = NULL;
cpufreq_policy_put_kobj()
If there is a reference held on the policy, i.e. obtained prior to the
unregister call, then cpufreq_policy_put_kobj() will wait until that
reference is dropped. So once subsys_interface_unregister() returns
there is no policy pointer in flight and no new reference can be
obtained. So that rwsem protection is useless.
The other usage of cpufreq_rwsem in show()/store() of the sysfs
interface is redundant as well because sysfs already does the proper
kobject_get()/put() pairs.
That leaves CPU hotplug versus module removal. The current
down_write() around the write_lock() in cpufreq_unregister_driver() is
silly at best as it protects actually nothing.
The trivial solution to this is to prevent hotplug across
cpufreq_unregister_driver completely.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Exynos5250 based platforms have switched over to use generic
cpufreq driver for cpufreq functionality. So the Exynos
specific cpufreq support for these platforms can be removed.
Cc: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[k.kozlowski: Rebased the patch around exynos-cpufreq.c]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
freq_table should be alloced in ->init and freed in ->exit, but it
it is not freed. Fix this memory leak in acpi_cpufreq_cpu_exit().
Signed-off-by: Pan Xinhui <xinhuix.pan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
freq_table is now stored as policy->freq_table, so drop the redundant
freq_table from struct cpufreq_acpi_io.
Signed-off-by: Pan Xinhui <xinhuix.pan@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpb sysfs attribute is only exposed by the ACPI cpufreq driver
after a runtime check. For this purpose, the driver keeps a NULL
placeholder in its table of sysfs attributes and replaces the NULL
with a pointer to an attribute structure if it decides to expose
cpb.
That is confusing, so make the driver set the pointer to the cpb
attribute structure upfront and replace it with NULL if the
attribute should not be exposed instead.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
After commit 8cfcfd3900 (acpi-cpufreq: Fix an ACPI perf unregister
issue) we store both a pointer to per-CPU data of the first policy
CPU and the number of that CPU which are redundant.
Since the CPU number has to be stored anyway for the unregistration,
the pointer to the CPU's per-CPU data may be dropped and we can
access the data in question via per_cpu_ptr().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
acpi_processor_unregister_performance() actually doesn't use its
first argument, so drop it and update the callers accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Return codes aren't honored properly in cpufreq_set_policy(). This can
lead to two problems:
- wrong errors propagated to sysfs
- we try to do next state-change even if the previous one failed
cpufreq_governor_dbs() now returns proper errors on all invalid
state-transition requests and this code should honor that.
Reviewed-and-tested-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With previous commit, governors have started to return errors on invalid
state-transition requests. We already have a WARN for an invalid
state-transition request in cpufreq_governor_dbs(). This does trigger
today, as the sequence of events isn't guaranteed by cpufreq core.
Lets stop warning on that for now, and make sure we don't enter an
invalid state.
Reviewed-and-tested-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There can be races where the request has come to a wrong state. For
example INIT followed by STOP (instead of START) or START followed by
EXIT (instead of STOP).
Address these races by making sure the state-machine never gets into
any invalid state. Also return an error if an invalid state-transition
is requested.
Reviewed-and-tested-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some part of cs_dbs_timer() and od_dbs_timer() is exactly same and is
unnecessarily duplicated.
Create the real work-handler in cpufreq_governor.c and put the common
code in this routine (dbs_timer()).
Shouldn't make any functional change.
Reviewed-and-tested-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some information is common to all CPUs belonging to a policy, but are
kept on per-cpu basis. Lets keep that in another structure common to all
policy->cpus. That will make updates/reads to that less complex and less
error prone.
The memory for cpu_common_dbs_info is allocated/freed at INIT/EXIT, so
that it we don't reallocate it for STOP/START sequence. It will be also
be used (in next patch) while the governor is stopped and so must not be
freed that early.
Reviewed-and-tested-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Just call it 'policy', cur_policy is unnecessarily long and doesn't
have any special meaning.
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is called as 'cdbs' at most of the places and 'cpu_dbs' at others.
Lets use 'cdbs' consistently for better readability.
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Its not common info to all CPUs, but a structure representing common
type of cpu info to both governor types. Lets drop 'common_' from its
name.
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Its not used at all, drop it.
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Delayed work was named as 'work' and to access work within it we do
work.work. Not much readable. Rename delayed_work as 'dwork'.
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
HWP previously was only enabled at driver load time, on the boot
CPU, however, HWP must be enabled per package. Move the code to
enable HWP to the cpufreq driver init path so that it will be
called per CPU.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Tested-by: David Zhuang <david.zhuang@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fixed coding style issues found by checkpatch.pl tool. Changed
space indentation to tab, removed unneccesary braces, removed
space between MODULE macros and parentheses.
REMARKS: failed to 'make' this file with error message
'fatal error: asm/mach-types.h: No such file or directory'.
Signed-off-by: Cristian Ardelean <cristian97.ardelean@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As policy->cpu may not be same in acpi_cpufreq_cpu_init() and
acpi_cpufreq_cpu_exit(). There is a risk that we use different CPU
to un/register ACPI performance. So acpi_processor_unregister_performance()
may not be able to do the cleanup work. That causes a memory leak. And
if there will be another acpi_processor_register_performance() call,
it may also fail thanks to the internal check of pr->performace.
So add a new struct acpi_cpufreq_data field, acpi_perf_cpu, to fix
this issue.
Signed-off-by: Pan Xinhui <xinhuix.pan@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_init_policy() can fail, and we don't do anything except a call
to ->exit() on that. The policy should be freed if this happens.
Do it properly.
Reported-and-tested-by: "Jon Medhurst (Tixy)" <tixy@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These labels are are named in two ways normally:
- Based on what caused to jump to such labels
- Based on what we do under such labels
We follow the first naming convention today and that leads to multiple
labels for doing the same work. Fix it by switching to the second way of
naming them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Drivers can store their internal per-policy information in
policy->driver_data, lets use it.
we have benefits after this replacing.
1) memory saving.
2) policy is shared by several cpus, per_cpu seems not correct. using
*driver_data* is more reasonable.
3) fix a memory leak in acpi_cpufreq_cpu_exit. as policy->cpu might
change during cpu hotplug. So sometimes we cant't free *data*, use
*driver_data* to fix it.
4) fix a zero return value of get_cur_freq_on_cpu. Only per_cpu of
policy->cpu is set to *data*, if we try to get cpufreq on other cpus, we
get zero instead of correct values. Use *driver_data* to fix it.
Signed-off-by: Pan Xinhui <xinhuix.pan@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpuidle:
suspend-to-idle: Prevent RCU from complaining about tick_freeze()
* pm-cpufreq:
cpufreq: Allow freq_table to be obtained for offline CPUs
cpufreq: Initialize the governor again while restoring policy
* acpi-resources:
ACPI / PCI: Fix regressions caused by resource_size_t overflow with 32-bit kernel
Add a new cpufreq driver for Tegra124. Instead of using the PLLX as
the CPU clocksource, switch immediately to the DFLL. It allows the use
of higher clock rates, and will automatically scale the CPU voltage as
well. Besides the CPU clocksource switch, we let the cpufreq-dt driver
for all the cpufreq operations.
This driver also relies on the DFLL driver to fill the OPP table for the
CPU0 device, so that the cpufreq-dt driver knows what frequencies to
use.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra124 will use a different driver for frequency scaling, so
rename the old driver (which handles only Tegra20) appropriately.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Users of freq table may want to access it for any CPU from
policy->related_cpus mask. One such user is cpu-cooling layer. It gets a
list of 'clip_cpus' (equivalent to policy->related_cpus) during
registration and tries to get freq_table for the first CPU of this mask.
If the CPU, for which it tries to fetch freq_table, is offline,
cpufreq_frequency_get_table() fails. This happens because it relies on
cpufreq_cpu_get_raw() for its functioning which returns policy only for
online CPUs.
The fix is to access the policy data structure for the given CPU
directly (which also returns a valid policy for offline CPUs), but the
policy itself has to be active (meaning that at least one CPU using it
is online) for the frequency table to be returned.
Because we will be using 'cpufreq_cpu_data' now, which is internal to
the cpufreq core, move cpufreq_frequency_get_table() to cpufreq.c.
Reported-and-tested-by: Pi-Cheng Chen <pi-cheng.chen@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When all CPUs of a policy are hot-unplugged, we EXIT the governor but
don't mark policy->governor as NULL. This was done in order to keep last
used governor's information intact in sysfs, while the CPUs are offline.
But we also need to clear policy->governor when restoring the policy.
Because policy->governor still points to the last governor while policy
is restored, following sequence of event happens:
- cpufreq_init_policy() called while restoring policy
- find_governor() matches last_governor string for present governors and
returns last used governor's pointer, say ondemand. policy->governor
already has the same address, unless the governor was removed in
between.
- cpufreq_set_policy() is called with both old/new policies governor set
as ondemand.
- Because governors matched, we skip governor initialization and return
after calling __cpufreq_governor(CPUFREQ_GOV_LIMITS). Because the
governor wasn't initialized for this policy, it returned -EBUSY.
- cpufreq_init_policy() exits the policy on this error, but doesn't
destroy it properly (should be fixed separately).
- And so we enter a scenario where the policy isn't completely
initialized but used.
Fix this by setting policy->governor to NULL while restoring the policy.
Reported-and-tested-by: Pi-Cheng Chen <pi-cheng.chen@linaro.org>
Reported-and-tested-by: "Jon Medhurst (Tixy)" <tixy@linaro.org>
Reported-and-tested-by: Steven Rostedt <rostedt@goodmis.org>
Fixes: 18bf3a124e (cpufreq: Mark policy->governor = NULL for inactive policies)
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that there is no paravirt TSC, the "native" is
inappropriate. The function does RDTSC, so give it the obvious
name: rdtsc().
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Link: http://lkml.kernel.org/r/fd43e16281991f096c1e4d21574d9e1402c62d39.1434501121.git.luto@kernel.org
[ Ported it to v4.2-rc1. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WLBw
-----END PGP SIGNATURE-----
Merge tag 'module-builtin_driver-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull module_platform_driver replacement from Paul Gortmaker:
"Replace module_platform_driver with builtin_platform driver in non
modules.
We see an increasing number of non-modular drivers using
modular_driver() type register functions. There are several downsides
to letting this continue unchecked:
- The code can appear modular to a reader of the code, and they won't
know if the code really is modular without checking the Makefile
and Kconfig to see if compilation is governed by a bool or
tristate.
- Coders of drivers may be tempted to code up an __exit function that
is never used, just in order to satisfy the required three args of
the modular registration function.
- Non-modular code ends up including the <module.h> which increases
CPP overhead that they don't need.
- It hinders us from performing better separation of the module init
code and the generic init code.
So here we introduce similar macros for builtin drivers. Then we
convert builtin drivers (controlled by a bool Kconfig) by making the
following type of mapping:
module_platform_driver() ---> builtin_platform_driver()
module_platform_driver_probe() ---> builtin_platform_driver_probe().
The set of drivers that are converted here are just the ones that
showed up as relying on an implicit include of <module.h> during a
pending header cleanup. So we convert them here vs adding an include
of <module.h> to non-modular code to avoid compile fails. Additonal
conversions can be done asynchronously at any time.
Once again, an unused module_exit function that is removed here
appears in the diffstat as an outlier wrt all the other changes"
* tag 'module-builtin_driver-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
drivers/clk: convert sunxi/clk-mod0.c to use builtin_platform_driver
drivers/power: Convert non-modular syscon-reboot to use builtin_platform_driver
drivers/soc: Convert non-modular soc-realview to use builtin_platform_driver
drivers/soc: Convert non-modular tegra/pmc to use builtin_platform_driver
drivers/cpufreq: Convert non-modular s5pv210-cpufreq.c to use builtin_platform_driver
drivers/cpuidle: Convert non-modular drivers to use builtin_platform_driver
drivers/platform: Convert non-modular pdev_bus to use builtin_platform_driver
platform_device: better support builtin boilerplate avoidance
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qotW
-----END PGP SIGNATURE-----
Merge tag 'module-implicit-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull implicit module.h fixes from Paul Gortmaker:
"Fix up implicit <module.h> users that will break later.
The files changed here are simply modular source files that are
implicitly relying on <module.h> being present. We fix them up now,
so that we can decouple some of the module related init code from the
core init code in the future.
The addition of the module.h include to several files here is also a
no-op from a code generation point of view, else there would already
be compile issues with these files today.
There may be lots more implicit includes of <module.h> in tree, but
these are the ones that extensive build test coverage has shown that
must be fixed in order to avoid build breakage fallout for the pending
module.h <---> init.h code relocation we desire to complete"
* tag 'module-implicit-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
frv: add module.h to mb93090-mb00/flash.c to avoid compile fail
drivers/cpufreq: include <module.h> for modular exynos-cpufreq.c code
drivers/staging: include <module.h> for modular android tegra_ion code
crypto/asymmetric_keys: pkcs7_key_type needs module.h
sh: mach-highlander/psw.c is tristate and should use module.h
drivers/regulator: include <module.h> for modular max77802 code
drivers/pcmcia: include <module.h> for modular xxs1500_ss code
drivers/hsi: include <module.h> for modular omap_ssi code
drivers/gpu: include <module.h> for modular rockchip code
drivers/gpio: include <module.h> for modular crystalcove code
drivers/clk: include <module.h> for clk-max77xxx modular code
drivers and updates to existing ones, as usual. There are some fixes to
the framework itself and several cleanups for sparse warnings, etc.
Please consider pulling.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Iv72
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clock framework updates from Michael Turquette:
"The changes to the common clock framework for 4.2 are dominated by new
drivers and updates to existing ones, as usual.
There are some fixes to the framework itself and several cleanups for
sparse warnings, etc"
* tag 'clk-for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (135 commits)
clk: stm32: Add clock driver for STM32F4[23]xxx devices
dt-bindings: Document the STM32F4 clock bindings
cpufreq: exynos: remove Exynos4210 specific cpufreq driver support
ARM: Exynos: switch to using generic cpufreq driver for Exynos4210
clk: samsung: exynos4: add cpu clock configuration data and instantiate cpu clock
clk: samsung: add infrastructure to register cpu clocks
clk: add CLK_RECALC_NEW_RATES clock flag for Exynos cpu clock support
doc: dt: add documentation for lpc1850-ccu clk driver
clk: add lpc18xx ccu clk driver
doc: dt: add documentation for lpc1850-cgu clk driver
clk: add lpc18xx cgu clk driver
clk: keystone: add support for post divider register for main pll
clk: mvebu: flag the crypto clk as CLK_IGNORE_UNUSED
clk: cygnus: remove Cygnus dummy clock binding
clk: cygnus: add clock support for Broadcom Cygnus
clk: Change bcm clocks build dependency
clk: iproc: add initial common clock support
clk: iproc: define Broadcom iProc clock binding
MAINTAINERS: update email for Michael Turquette
clk: meson: add some error handling in meson_clk_register_cpu()
...
Pull MIPS updates from Ralf Baechle:
- Improvements to the tlb_dump code
- KVM fixes
- Add support for appended DTB
- Minor improvements to the R12000 support
- Minor improvements to the R12000 support
- Various platform improvments for BCM47xx
- The usual pile of minor cleanups
- A number of BPF fixes and improvments
- Some improvments to the support for R3000 and DECstations
- Some improvments to the ATH79 platform support
- A major patchset for the JZ4740 SOC adding support for the CI20 platform
- Add support for the Pistachio SOC
- Minor BMIPS/BCM63xx platform support improvments.
- Avoid "SYNC 0" as memory barrier when unlocking spinlocks
- Add support for the XWR-1750 board.
- Paul's __cpuinit/__cpuinitdata cleanups.
- New Malta CPU board support large memory so enable ZONE_DMA32.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits)
MIPS: spinlock: Adjust arch_spin_lock back-off time
MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA
MIPS: BCM47xx: Simplify handling SPROM revisions
MIPS: Cobalt Don't use module_init in non-modular MTD registration.
MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/
MIPS: use for_each_sg()
MIPS: BCM47xx: Don't select BCMA_HOST_PCI
MIPS: BCM47xx: Add helper variable for storing NVRAM length
MIPS: IRQ/IP27: Move IRQ allocation API to platform code.
MIPS: Replace smp_mb with release barrier function in unlocks.
MIPS: i8259: DT support
MIPS: Malta: Basic DT plumbing
MIPS: include errno.h for ENODEV in mips-cm.h
MIPS: Define GCR_GIC_STATUS register fields
MIPS: BPF: Introduce BPF ASM helpers
MIPS: BPF: Use BPF register names to describe the ABI
MIPS: BPF: Move register definition to the BPF header
MIPS: net: BPF: Replace RSIZE with SZREG
MIPS: BPF: Free up some callee-saved registers
MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers
...
- ACPICA update to upstream revision 20150515 including basic
support for ACPI 6 features: new ACPI tables introduced by
ACPI 6 (STAO, XENV, WPBT, NFIT, IORT), changes related to the
other tables (DTRM, FADT, LPIT, MADT), new predefined names
(_BTH, _CR3, _DSD, _LPI, _MTL, _PRR, _RDI, _RST, _TFP, _TSN),
fixes and cleanups (Bob Moore, Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation
in Windows (Rafael J Wysocki).
- Rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling
of DMI quirks that may be involved in that and to make the
code generally more straightforward (Hans de Goede).
- Fixes for the ACPI Embedded Controller (EC) driver related to
the handling of EC transactions (Lv Zheng).
- Fix for a regression related to the ACPI resources management
and resulting from a recent change of ACPI initialization code
ordering (Rafael J Wysocki).
- Fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the
code that switches the platform over to the ACPI mode too
early in the initialization sequence (Rafael J Wysocki).
- Support for the ACPI _CCA device configuration object related
to DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- Cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- Assorted cleanups related to ACPI (Dominik Brodowski. Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- Fix for a long-standing issue causing General Protection Faults
to be generated occasionally on return to user space after resume
from ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- Fix to make the suspend core code return -EBUSY consistently in
all cases when system suspend is aborted due to wakeup detection
(Ruchi Kandoi).
- Support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- New tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- Wakeup sources framework enhancements (Jin Qian).
- New macro for noirq system PM callbacks (Grygorii Strashko).
- Assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should
reduce the overhead of these operations quite a bit, unless the
CPU in question is physically going away (Viresh Kumar, Saravana
Kannan).
- Serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- Assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- New Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- Updates for the common clock operations support code in the PM
core (Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- Fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- Runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=7jTj
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"The rework of backlight interface selection API from Hans de Goede
stands out from the number of commits and the number of affected
places perspective. The cpufreq core fixes from Viresh Kumar are
quite significant too as far as the number of commits goes and because
they should reduce CPU online/offline overhead quite a bit in the
majority of cases.
From the new featues point of view, the ACPICA update (to upstream
revision 20150515) adding support for new ACPI 6 material to ACPICA is
the one that matters the most as some new significant features will be
based on it going forward. Also included is an update of the ACPI
device power management core to follow ACPI 6 (which in turn reflects
the Windows' device PM implementation), a PM core extension to support
wakeup interrupts in a more generic way and support for the ACPI _CCA
device configuration object.
The rest is mostly fixes and cleanups all over and some documentation
updates, including new DT bindings for Operating Performance Points.
There is one fix for a regression introduced in the 4.1 cycle, but it
adds quite a number of lines of code, it wasn't really ready before
Thursday and you were on vacation, so I refrained from pushing it on
the last minute for 4.1.
Specifics:
- ACPICA update to upstream revision 20150515 including basic support
for ACPI 6 features: new ACPI tables introduced by ACPI 6 (STAO,
XENV, WPBT, NFIT, IORT), changes related to the other tables (DTRM,
FADT, LPIT, MADT), new predefined names (_BTH, _CR3, _DSD, _LPI,
_MTL, _PRR, _RDI, _RST, _TFP, _TSN), fixes and cleanups (Bob Moore,
Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation in
Windows (Rafael J Wysocki).
- rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling of
DMI quirks that may be involved in that and to make the code
generally more straightforward (Hans de Goede).
- fixes for the ACPI Embedded Controller (EC) driver related to the
handling of EC transactions (Lv Zheng).
- fix for a regression related to the ACPI resources management and
resulting from a recent change of ACPI initialization code ordering
(Rafael J Wysocki).
- fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the code
that switches the platform over to the ACPI mode too early in the
initialization sequence (Rafael J Wysocki).
- support for the ACPI _CCA device configuration object related to
DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- assorted cleanups related to ACPI (Dominik Brodowski, Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- fix for a long-standing issue causing General Protection Faults to
be generated occasionally on return to user space after resume from
ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- fix to make the suspend core code return -EBUSY consistently in all
cases when system suspend is aborted due to wakeup detection (Ruchi
Kandoi).
- support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- new tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- wakeup sources framework enhancements (Jin Qian).
- new macro for noirq system PM callbacks (Grygorii Strashko).
- assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should reduce
the overhead of these operations quite a bit, unless the CPU in
question is physically going away (Viresh Kumar, Saravana Kannan).
- serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- new Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- updates for the common clock operations support code in the PM core
(Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski)"
* tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (194 commits)
cpuidle: powernv/pseries: Auto-promotion of snooze to deeper idle state
x86: Load __USER_DS into DS/ES after resume
PM / OPP: Add binding for 'opp-suspend'
PM / OPP: Allow multiple OPP tables to be passed via DT
PM / OPP: Add new bindings to address shortcomings of existing bindings
ACPI: Constify ACPI device IDs in documentation
ACPI / enumeration: Document the rules regarding the PRP0001 device ID
ACPI / video: Make acpi_video_unregister_backlight() private
acpi-video-detect: Remove old API
toshiba-acpi: Port to new backlight interface selection API
thinkpad-acpi: Port to new backlight interface selection API
sony-laptop: Port to new backlight interface selection API
samsung-laptop: Port to new backlight interface selection API
msi-wmi: Port to new backlight interface selection API
msi-laptop: Port to new backlight interface selection API
intel-oaktrail: Port to new backlight interface selection API
ideapad-laptop: Port to new backlight interface selection API
fujitsu-laptop: Port to new backlight interface selection API
eeepc-laptop: Port to new backlight interface selection API
dell-wmi: Port to new backlight interface selection API
...
Pull x86 core updates from Ingo Molnar:
"There were so many changes in the x86/asm, x86/apic and x86/mm topics
in this cycle that the topical separation of -tip broke down somewhat -
so the result is a more traditional architecture pull request,
collected into the 'x86/core' topic.
The topics were still maintained separately as far as possible, so
bisectability and conceptual separation should still be pretty good -
but there were a handful of merge points to avoid excessive
dependencies (and conflicts) that would have been poorly tested in the
end.
The next cycle will hopefully be much more quiet (or at least will
have fewer dependencies).
The main changes in this cycle were:
* x86/apic changes, with related IRQ core changes: (Jiang Liu, Thomas
Gleixner)
- This is the second and most intrusive part of changes to the x86
interrupt handling - full conversion to hierarchical interrupt
domains:
[IOAPIC domain] -----
|
[MSI domain] --------[Remapping domain] ----- [ Vector domain ]
| (optional) |
[HPET MSI domain] ----- |
|
[DMAR domain] -----------------------------
|
[Legacy domain] -----------------------------
This now reflects the actual hardware and allowed us to distangle
the domain specific code from the underlying parent domain, which
can be optional in the case of interrupt remapping. It's a clear
separation of functionality and removes quite some duct tape
constructs which plugged the remap code between ioapic/msi/hpet
and the vector management.
- Intel IOMMU IRQ remapping enhancements, to allow direct interrupt
injection into guests (Feng Wu)
* x86/asm changes:
- Tons of cleanups and small speedups, micro-optimizations. This
is in preparation to move a good chunk of the low level entry
code from assembly to C code (Denys Vlasenko, Andy Lutomirski,
Brian Gerst)
- Moved all system entry related code to a new home under
arch/x86/entry/ (Ingo Molnar)
- Removal of the fragile and ugly CFI dwarf debuginfo annotations.
Conversion to C will reintroduce many of them - but meanwhile
they are only getting in the way, and the upstream kernel does
not rely on them (Ingo Molnar)
- NOP handling refinements. (Borislav Petkov)
* x86/mm changes:
- Big PAT and MTRR rework: making the code more robust and
preparing to phase out exposing direct MTRR interfaces to drivers -
in favor of using PAT driven interfaces (Toshi Kani, Luis R
Rodriguez, Borislav Petkov)
- New ioremap_wt()/set_memory_wt() interfaces to support
Write-Through cached memory mappings. This is especially
important for good performance on NVDIMM hardware (Toshi Kani)
* x86/ras changes:
- Add support for deferred errors on AMD (Aravind Gopalakrishnan)
This is an important RAS feature which adds hardware support for
poisoned data. That means roughly that the hardware marks data
which it has detected as corrupted but wasn't able to correct, as
poisoned data and raises an APIC interrupt to signal that in the
form of a deferred error. It is the OS's responsibility then to
take proper recovery action and thus prolonge system lifetime as
far as possible.
- Add support for Intel "Local MCE"s: upcoming CPUs will support
CPU-local MCE interrupts, as opposed to the traditional system-
wide broadcasted MCE interrupts (Ashok Raj)
- Misc cleanups (Borislav Petkov)
* x86/platform changes:
- Intel Atom SoC updates
... and lots of other cleanups, fixlets and other changes - see the
shortlog and the Git log for details"
* 'x86-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (222 commits)
x86/hpet: Use proper hpet device number for MSI allocation
x86/hpet: Check for irq==0 when allocating hpet MSI interrupts
x86/mm/pat, drivers/infiniband/ipath: Use arch_phys_wc_add() and require PAT disabled
x86/mm/pat, drivers/media/ivtv: Use arch_phys_wc_add() and require PAT disabled
x86/platform/intel/baytrail: Add comments about why we disabled HPET on Baytrail
genirq: Prevent crash in irq_move_irq()
genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
iommu, x86: Properly handle posted interrupts for IOMMU hotplug
iommu, x86: Provide irq_remapping_cap() interface
iommu, x86: Setup Posted-Interrupts capability for Intel iommu
iommu, x86: Add cap_pi_support() to detect VT-d PI capability
iommu, x86: Avoid migrating VT-d posted interrupts
iommu, x86: Save the mode (posted or remapped) of an IRTE
iommu, x86: Implement irq_set_vcpu_affinity for intel_ir_chip
iommu: dmar: Provide helper to copy shared irte fields
iommu: dmar: Extend struct irte for VT-d Posted-Interrupts
iommu: Add new member capability to struct irq_remap_ops
x86/asm/entry/64: Disentangle error_entry/exit gsbase/ebx/usermode code
x86/asm/entry/32: Shorten __audit_syscall_entry() args preparation
x86/asm/entry/32: Explain reloading of registers after __audit_syscall_entry()
...
Currently, code of Loongson-2/3 is under loongson directory and code of
Loongson-1 is under loongson1 directory. Besides, there are Kconfig
options such as MACH_LOONGSON and MACH_LOONGSON1. This naming style is
very ugly and confusing. Since Loongson-2/3 are both 64-bit general-
purpose CPU while Loongson-1 is 32-bit SoC, we rename both file names
and Kconfig symbols from loongson/loongson1 to loongson64/loongson32.
[ralf@linux-mips.org: Resolve a number of simple conflicts.]
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Kelvin Cheung <keguang.zhang@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/9790/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Exynos4210 based platforms have switched over to use generic
cpufreq driver for cpufreq functionality. So the Exynos
specific cpufreq support for these platforms can be removed.
Changes by Bartlomiej:
- dropped Exynos5250 support removal for now
- updated exynos-cpufreq.[c,h]
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
by adding the missing MODULE_ALIAS(), cpufreq-dt
can be autoloaded by udev/systemd.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This file depends on a Kconfig option which is a bool, so
we use the appropriate registration function, which avoids us
relying on an implicit inclusion of <module.h> which we are
doing currently.
While this currently works, we really don't want to be including
the module.h header in non-modular code, which we'd be forced
to do, pending some upcoming code relocation from init.h into
module.h. So we fix it now by using the non-modular equivalent.
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: linux-pm@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This file is built off of a tristate Kconfig option ("ARM_EXYNOS_CPUFREQ")
and also contains modular function calls so it should explicitly include
module.h to avoid compile breakage during pending header shuffles.
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Each time the CPU switches its frequency, the clock nodes in
DTS are walked through to find proper clock source. This is
very time-consuming, for example, it is up to 500+ us on T4240.
Besides, switching time varies from clock to clock.
To optimize this, each input clock of CPU is buffered, so that
it can be picked up instantly when needed.
Since for each CPU each input clock is stored in a pointer
which takes 4 or 8 bytes memory and normally there are several
input clocks per CPU, that will not take much memory as well.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are several races reported in cpufreq core around governors (only
ondemand and conservative) by different people.
There are at least two race scenarios present in governor code:
(a) Concurrent access/updates of governor internal structures.
It is possible that fields such as 'dbs_data->usage_count', etc. are
accessed simultaneously for different policies using same governor
structure (i.e. CPUFREQ_HAVE_GOVERNOR_PER_POLICY flag unset). And
because of this we can dereference bad pointers.
For example consider a system with two CPUs with separate 'struct
cpufreq_policy' instances. CPU0 governor: ondemand and CPU1: powersave.
CPU0 switching to powersave and CPU1 to ondemand:
CPU0 CPU1
store* store*
cpufreq_governor_exit() cpufreq_governor_init()
dbs_data = cdata->gdbs_data;
if (!--dbs_data->usage_count)
kfree(dbs_data);
dbs_data->usage_count++;
*Bad pointer dereference*
There are other races possible between EXIT and START/STOP/LIMIT as
well. Its really complicated.
(b) Switching governor state in bad sequence:
For example trying to switch a governor to START state, when the
governor is in EXIT state. There are some checks present in
__cpufreq_governor() but they aren't sufficient as they compare events
against 'policy->governor_enabled', where as we need to take governor's
state into account, which can be used by multiple policies.
These two issues need to be solved separately and the responsibility
should be properly divided between cpufreq and governor core.
The first problem is more about the governor core, as it needs to
protect its structures properly. And the second problem should be fixed
in cpufreq core instead of governor, as its all about sequence of
events.
This patch is trying to solve only the first problem.
There are two types of data we need to protect,
- 'struct common_dbs_data': No matter what, there is going to be a
single copy of this per governor.
- 'struct dbs_data': With CPUFREQ_HAVE_GOVERNOR_PER_POLICY flag set, we
will have per-policy copy of this data, otherwise a single copy.
Because of such complexities, the mutex present in 'struct dbs_data' is
insufficient to solve our problem. For example we need to protect
fetching of 'dbs_data' from different structures at the beginning of
cpufreq_governor_dbs(), to make sure it isn't currently being updated.
This can be fixed if we can guarantee serialization of event parsing
code for an individual governor. This is best solved with a mutex per
governor, and the placeholder for that is 'struct common_dbs_data'.
And so this patch moves the mutex from 'struct dbs_data' to 'struct
common_dbs_data' and takes it at the beginning and drops it at the end
of cpufreq_governor_dbs().
Tested with and without following configuration options:
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_DEBUG_RT_MUTEXES=y
CONFIG_DEBUG_PI_LIST=y
CONFIG_DEBUG_SPINLOCK=y
CONFIG_DEBUG_MUTEXES=y
CONFIG_DEBUG_LOCK_ALLOC=y
CONFIG_PROVE_LOCKING=y
CONFIG_LOCKDEP=y
CONFIG_DEBUG_ATOMIC_SLEEP=y
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_governor_dbs() is hardly readable, it is just too big and
complicated. Lets make it more readable by splitting out event specific
routines.
Order of statements is changed at few places, but that shouldn't bring
any functional change.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Notifiers are required only for conservative governor and the common
governor code is unnecessarily polluted with that. Handle that from
cs_init/exit() instead of cpufreq_governor_dbs().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_update_policy() was kept as a separate routine earlier as it was
handling migration of sysfs directories, which isn't the case anymore.
It is only updating policy->cpu now and is called by a single caller.
The WARN_ON() isn't really required anymore, as we are just updating the
cpu now, not moving the sysfs directories.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
__cpufreq_remove_dev_finish() is doing two things today:
- Restarts the governor if some CPUs from concerned policy are still
online.
- Frees the policy if all CPUs are offline.
The first task of restarting the governor can be moved to
__cpufreq_remove_dev_prepare() to restart the governor early. There is
no race between _prepare() and _finish() as they would be handling
completely different cases. _finish() will only be required if we are
going to free the policy and that has nothing to do with restarting the
governor.
Original-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_policy_put_kobj() is actually part of freeing the policy and can
be called from cpufreq_policy_free() directly instead of a separate
call.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
policy->kobj is required to be initialized once in the lifetime of a
policy. Currently we are initializing it from __cpufreq_add_dev() and
that doesn't look to be the best place for doing so as we have to do
this on special cases (like: !recover_policy).
We can initialize it from a more obvious place cpufreq_policy_alloc()
and that will make code look cleaner, specially the error handling part.
The error handling part of __cpufreq_add_dev() was doing almost the same
thing while recover_policy is true or false. Fix that as well by always
calling cpufreq_policy_put_kobj() with an additional parameter to skip
notification part of it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When we hot-unplug a cpu, we remove its sysfs cpufreq directory and if
the outgoing cpu was the owner of policy->kobj earlier then we migrate
the sysfs directory to under another online cpu.
There are few disadvantages this brings:
- Code Complexity
- Slower hotplug/suspend/resume
- sysfs file permissions are reset after all policy->cpus are offlined
- CPUFreq stats history lost after all policy->cpus are offlined
- Special management of sysfs stuff during suspend/resume
To overcome these, this patch modifies the way sysfs directories are
managed:
- Select sysfs kobjects owner while initializing policy and don't change
it during hotplugs. Track it with kobj_cpu created earlier.
- Create symlinks for all related CPUs (can be offline) instead of
affected CPUs on policy initialization and remove them only when the
policy is freed.
- Free policy structure only on the removal of cpufreq-driver and not
during hotplug/suspend/resume, detected by checking 'struct
subsys_interface *' (Valid only when called from
subsys_interface_unregister() while unregistering driver).
Apart from this, special care is taken to handle physical hoplug of CPUs
as we wouldn't remove sysfs links or remove policies on logical
hotplugs. Physical hotplug happens in the following sequence.
Hot removal:
- CPU is offlined first, ~ 'echo 0 >
/sys/devices/system/cpu/cpuX/online'
- Then its device is removed along with all sysfs files, cpufreq core
notified with cpufreq_remove_dev() callback from subsys-interface..
Hot addition:
- First the device along with its sysfs files is added, cpufreq core
notified with cpufreq_add_dev() callback from subsys-interface..
- CPU is onlined, ~ 'echo 1 > /sys/devices/system/cpu/cpuX/online'
We call the same routines with both hotplug and subsys callbacks, and we
sense physical hotplug with cpu_offline() check in subsys callback. We
can handle most of the stuff with regular hotplug callback paths and
add/remove cpufreq sysfs links or free policy from subsys callbacks.
Original-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Later commits would change the way policies are managed today. Policies
wouldn't be freed on cpu hotplug (currently they aren't freed only for
suspend), and while the CPU is offline, the sysfs cpufreq files would
still be present.
User may accidentally try to update the sysfs files in following
directory: '/sys/devices/system/cpu/cpuX/cpufreq/'. And that would
result in undefined behavior as policy wouldn't be active then.
Apart from updating the store() routine, we also update __cpufreq_get()
which can call cpufreq_out_of_sync(). The later routine tries to update
policy->cur and starts notifying kernel about it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
During initialization and exit it is possible that the target pstate
might not actually be set. Furthermore, the result can be that the
driver and the processor are out of synch and, under some conditions,
the driver might never send the processor the proper target pstate.
This patch adds a bypass or do_checks flag to the call to
intel_pstate_set_pstate. If bypass, then specifically bypass clamp
checks and the do not send if it is the same as last time check. If
do_checks, then, and as before, do the current policy clamp checks,
and do not do actual send if the new target is the same as the old.
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Reported-by: Marien Zwart <marien.zwart@gmail.com>
Reported-by: Alex Lochmann <alexander.lochmann@tu-dortmund.de>
Reported-by: Piotr Ko?aczkowski <pkolaczk@gmail.com>
Reported-by: Clemens Eisserer <linuxhippy@gmail.com>
Tested-by: Marien Zwart <marien.zwart@gmail.com>
Tested-by: Doug Smythies <dsmythies@telus.net>
[ rjw: Dropped pointless symbol definitions, rebased ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit ce717613f3 (intel_pstate: Turn per cpu printk into pr_debug)
turned per cpu printk into pr_debug. However, only half of the change
was done, introducing an inconsistency between entry and exit from
driver pstate control. This patch changes the exit message to pr_debug
also.
The various messages are inconsistent with respect to any identifier
text that can be used to help isolate the desired information from a
huge log. This patch makes a consistent identifier portion of the
string.
Amends: ce717613f3 (intel_pstate: Turn per cpu printk into pr_debug)
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Nothing in <asm/io.h> uses anything from <linux/vmalloc.h>, so
remove it from there and fix up the resulting build problems
triggered on x86 {64|32}-bit {def|allmod|allno}configs.
The breakages were triggering in places where x86 builds relied
on vmalloc() facilities but did not include <linux/vmalloc.h>
explicitly and relied on the implicit inclusion via <asm/io.h>.
Also add:
- <linux/init.h> to <linux/io.h>
- <asm/pgtable_types> to <asm/io.h>
... which were two other implicit header file dependencies.
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
[ Tidied up the changelog. ]
Acked-by: David Miller <davem@davemloft.net>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Colin Cross <ccross@android.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: James E.J. Bottomley <JBottomley@odin.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Kristen Carlson Accardi <kristen@linux.intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Suma Ramars <sramars@cisco.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The former duplicates the functionality of the latter but is
neither documented nor arch-independent.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1432645896-12588-8-git-send-email-bgolaszewski@baylibre.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The former duplicate the functionalities of the latter but are
neither documented nor arch-independent.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1432645896-12588-7-git-send-email-bgolaszewski@baylibre.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The former duplicates the functionality of the latter but is
neither documented nor arch-independent.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1432645896-12588-6-git-send-email-bgolaszewski@baylibre.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The former duplicates the functionality of the latter but is
neither documented nor arch-independent.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1432645896-12588-5-git-send-email-bgolaszewski@baylibre.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In order to prepare for the next few commits, that will stop migrating
sysfs files on cpu hotplug, this patch starts managing sysfs-cpu
separately.
The behavior is still the same as we are still migrating sysfs files on
hotplug, later commits would change that.
Signed-off-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Later commits would change the way policies are managed today. Policies
wouldn't be freed on cpu hotplug (currently they aren't freed on
suspend), and while the CPU is offline, the sysfs cpufreq files would
still be present.
Because we don't mark policy->governor as NULL, it still contains
pointer of the last used governor. And if the governor is removed, while
all the CPUs of a policy are hotplugged out, this pointer wouldn't be
valid anymore. And if we try to read the 'scaling_governor', etc. from
sysfs, it will result in kernel OOPs.
To prevent this, mark policy->governor as NULL for all inactive policies
while the governor is removed from kernel.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
History of which governor was used last is common to all CPUs within a
policy and maintaining it per-cpu isn't the best approach for sure.
Apart from wasting memory, this also increases the complexity of
managing this data structure as it has to be updated for all CPUs.
To make that somewhat simpler, lets store this information in a new
field 'last_governor' in struct cpufreq_policy and update it on removal
of last cpu of a policy.
As a side-effect it also solves an old problem, consider a system with
two clusters 0 & 1. And there is one policy per cluster.
Cluster 0: CPU0 and 1.
Cluster 1: CPU2 and 3.
- CPU2 is first brought online, and governor is set to performance
(default as cpufreq_cpu_governor wasn't set).
- Governor is changed to ondemand.
- CPU2 is taken offline and cpufreq_cpu_governor is updated for CPU2.
- CPU3 is brought online.
- Because cpufreq_cpu_governor wasn't set for CPU3, the default governor
performance is picked for CPU3.
This patch fixes the bug as we now have a single variable to update for
policy.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We reach here while adding policy for a CPU and enter into the 'if'
block only if a policy already exists for the CPU.
As cpufreq_cpu_data is set for all policy->related_cpus now, when the
policy is first added, we can use that to find the CPU's policy instead
of traversing the list of all active policies.
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We can extract the same information from cpufreq_cpu_data as it is also
available for inactive policies now. And so don't need
cpufreq_cpu_data_fallback anymore.
Also add a WARN_ON() for the case where we try to restore from an active
policy.
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that we can check policy->cpus to find if policy is active or not,
we don't need to clean cpufreq_cpu_data and delete policy from the list
on light weight tear down of policies (like in suspend).
To make it consistent and clean, set cpufreq_cpu_data for all related
CPUs when the policy is first created and clean it only while it is
freed.
Also update cpufreq_cpu_get_raw() to check if cpu is part of
policy->cpus mask, so that we don't end up getting policies for offline
CPUs.
In order to make sure that no users of 'policy' are using an inactive
policy, use cpufreq_cpu_get_raw() instead of directly accessing
cpufreq_cpu_data.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
policy->cpus is cleared unconditionally now on hotplug-out of a CPU and
it can be checked to know if a policy is active or not. Create helper
routines to iterate over all active/inactive policies, based on
policy->cpus field.
Replace all instances of for_each_policy() with for_each_active_policy()
to make them iterate only for active policies. (We haven't made changes
yet to keep inactive policies in the same list, but that will be
followed in a later patch).
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With the addition of switcher code, there's compile-time dependency on
BIG_LITTLE to get arm_big_little driver compiling on ARM64. Since ARM64
will never add support for bL switcher, it's better to remove the
dependency so that the driver can be reused on ARM64 platforms.
This patch adds stubs to remove BIG_LITTLE dependency in the driver.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 007bea098b (intel_pstate: Add setting voltage value for
baytrail P states.) introduced byt_set_pstate() with the assumption that
it would always be run by the CPU whose MSR is to be written by it. It
turns out, however, that is not always the case in practice, so modify
byt_set_pstate() to enforce the MSR write done by it to always happen on
the right CPU.
Fixes: 007bea098b (intel_pstate: Add setting voltage value for baytrail P states.)
Signed-off-by: Joe Konno <joe.konno@intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We clear policy->cpus mask while CPUs are hotplugged out. We do it for all CPUs
except the last CPU of the policy. I don't remember what the rationale behind
that was, but I couldn't think of anything that will break if we remove this
conditional clearing and always clear policy->cpus.
The benefit we get out of it is, we can know if a policy is active or not by
checking if this field is empty or not. That will be used by later commits.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are two cases when we may try to add CPUs we're already handling:
- On boot, the first cpu has marked all policy->cpus managed and so we
will find policy for all other policy->cpus later on.
- When a managed cpu is hotplugged out and later brought back in.
Currently, separate paths and checks take care of the two. While the
first one is detected by testing cpu against 'policy->cpus', the other
one is detected by testing cpu against 'policy->related_cpus'.
We can handle them both via a single path and there is no need to do
special checking for the first one.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
[ rjw: Changelog, comments ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Simply returning here with an error is not enough. It shouldn't be allowed at
all to try calling cpufreq_cpu_get() for an invalid CPU.
Add a WARN here to make it clear that it wouldn't be acceptable at all.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_add_dev() is an unnecessary wrapper over __cpufreq_add_dev(). Merge
them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This clearly states what the code inside these routines is doing and how these
must be used.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The intel_pstate driver is difficult to debug and investigate without tsc.
Also, it is likely use of tsc, and some version of C0 percentage,
will be re-introdcued in futute.
There have also been occasions where it is desirebale to know, and
confirm, the previous target pstate.
This patch brings back tsc, adds previous target pstate,
and adds both to the trace data collection.
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The "cpu-cluster.<n>" used to get the cluster clock is not used by any
platform. Moreover __of_clk_get_by_name used in clk_get return error if
the "clock-names" in the DT doesn't match this string. When using DT,
it's not compulsory to specify the clock name unless there are multiple
clock input entries in the consumer.
This patch removes the unused clock string from the driver.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The actual frequency is set through "clk_change_rate" which is void
function. If the underlying hardware fails and returns error, the error
is lost in the clk layer. In order to track such failures, we need to
read back the frequency(just the cached value as clk_recalc called after
clk->ops->set_rate gets the frequency)
This patch adds check to see if the frequency is set correctly or if
they were any hardware failures and sends the appropriate errors to the
cpufreq core.
Reviewed-by: Michael Turquette <mike.turquette@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pxa255_run_freqs and pxa255_turbo_freqs are only read.
This patch updates arrays declaration, find_freq_tables()
and its callsites.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
typedef is not really useful here. Replace it by structure
to improve readability. typedef should only be used in some cases.
(See Documentation/CodingStyle Chapter 5 for details).
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
I keep seeing
drivers/cpufreq/intel_pstate.c: In function ‘intel_pstate_init’:
drivers/cpufreq/intel_pstate.c:1187:26: warning: initialization from incompatible pointer type
struct cpuinfo_x86 *c = &boot_cpu_data;
when doing randconfig builds.
This is caused by the fact that when !CONFIG_SMP, asm/processor.h
defines cpu_info to boot_cpu_data and the local variable
struct cpu_defaults *cpu_info
overshadows it leading to this unfortunate assignment in the
preprocessed source:
struct cpu_defaults *boot_cpu_data;
struct cpuinfo_x86 *c = &boot_cpu_data;
Rename the local variable and use static_cpu_has_safe() which alleviates
the need for defining a local cpuinfo_x86 pointer.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Change the setpoint for the Baytrail and Cherrytrail CPUs. This
will cause more aggressive pstate selection and improves
performance on a variety of workloads with little power penalty.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
1. Add Knights Landing (KNL) CPUID to the list of CPUIDs supported by
the intel_pstate driver.
2. Add a new cpu_default structure for KNL since KNL has a slightly
different mechanism to get turbo pstates from MSRs.
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
[ rjw: Subject and changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
x86_match_cpu will not match our cpuid unless APERF/MPERF flag is
set, so there is no need to do the manual check for this MSR.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The qoriq-cpufreq driver contains a hack for powerpc to include
asm/smp.h on uniprocessor builds so it can get the hardware CPU
number. On ARM, it does not require this hack, but instead gets
a compile error:
In file included from drivers/cpufreq/qoriq-cpufreq.c:24:0:
arch/arm/include/asm/smp.h:18:3: error: #error "<asm/smp.h> included in non-SMP build"
arch/arm/include/asm/smp.h:21:0: warning: "raw_smp_processor_id" redefined
This adds an #ifdef to mirror the one in its get_cpu_physical_id()
function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 2f249358ee ("cpufreq: qoriq: rename the driver")
Cc: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
All CPUs leaving the first-online CPU are hotplugged out on suspend and
and cpufreq core stops managing them.
On resume, we need to call cpufreq_update_policy() for this CPU's policy
to make sure its frequency is in sync with cpufreq's cached value, as it
might have got updated by hardware during suspend/resume.
The policies are always added to the top of the policy-list. So, in
normal circumstances, CPU 0's policy will be the last one in the list.
And so the code checks for the last policy.
But there are cases where it will fail. Consider quad-core system, with
policy-per core. If CPU0 is hotplugged out and added back again, the
last policy will be on CPU1 :(
To fix this in a proper way, always look for the policy of the first
online CPU. That way we will be sure that we are calling
cpufreq_update_policy() for the only CPU that wasn't hotplugged out.
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+
Fixes: 2f0aea9363 ("cpufreq: suspend governors on system suspend/hibernate")
Reported-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add acpu driver for hisilicon SoC, acpu is application processor
subsystem. Currently the acpu has the coupled clock domain for two
clusters, so this driver will directly use cpufreq-dt driver as
backend.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The power and thermal safety of the system is taken care by an
On-Chip-Controller (OCC) which is real-time subsystem embedded within
the POWER8 processor. OCC continuously monitors the memory and core
temperature, the total system power, state of power supply and fan.
The cpu frequency can be throttled by OCC for the following reasons:
1)If a processor crosses its power and temperature limit then OCC will
lower its Pmax to reduce the frequency and voltage.
2)If OCC crashes then the system is forced to Psafe frequency.
3)If OCC fails to recover then the kernel is not allowed to do any
further frequency changes and the chip will remain in Psafe.
The user can see a drop in performance when frequency is throttled and
is unaware of throttling. So detect and report such a condition, so
the user can check the OCC status to reboot the system or check for
power supply or fan failures.
The current status of the core is read from Power Management Status
Register(PMSR) to check if any of the throttling condition is occurred
and the appropriate throttling message is reported.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This driver works on all QorIQ platforms which include
ARM-based cores and PPC-based cores.
Rename it in order to represent better.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Freescale introduced new ARM core-based SoCs which support dynamic
frequency switch feature. DFS on new SoCs are compatible with current
PowerPC CoreNet platforms. In order to support those new platforms,
this driver needs to be updated. The main changes include:
1. Changed the names of functions in driver.
2. Added two new functions get_cpu_physical_id() and get_bus_freq().
3. Used a new way to get the CPU mask which share clock wire.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull thermal management fixes from Eduardo Valentin:
"Specifics:
- adding Lukasz as maintainer of samsung thermal driver.
- driver fixes: exynos and int430x.
- one fix in the exynos cpufreq driver related to cpu cooling (acked
by cpufreq maintainer).
- fix default sysfs attributes of cooling devices
Note: I am sending this pull on Rui's behalf while he fixes issues in his Linux box"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: Make sysfs attributes of cooling devices default attributes
Thermal/int340x: Fix memleak for aux trip
MAINTAINERS: Add entry for SAMSUNG THERMAL DRIVER
cpufreq: exynos: Use simple approach to asses if cpu cooling can be used
thermal: exynos: Fix wrong control of power down detection mode for Exynos7
If CONFIG_SMP=n, <linux/smp.h> does not include <asm/smp.h>, causing:
drivers/cpufreq/ppc-corenet-cpufreq.c: In function 'corenet_cpufreq_cpu_init':
drivers/cpufreq/ppc-corenet-cpufreq.c:173:3: error: implicit declaration of function 'get_hard_smp_processor_id' [-Werror=implicit-function-declaration]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit: e725d26c48 provided possibility to
use device tree to asses if cpu can be used as cooling device. Since the
code was somewhat awkward, simpler approach has been proposed.
Test HW: Exynos 4412 - Odroid U3.
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
- Revert a recent ACPI LPSS driver commit that prevented the touchpad
driver from loading on Dell XPS13 (Jarkko Nikula).
- Make the ACPI LPSS driver disable the I2C controllers and deassert
SPI host controllers resets at startup on Intel BayTrail and Braswell
SoCs in case they have been left in wrong states by the platform
firmware which then may casuse fatal controller driver failures during
resume from hibernation (Mika Westerberg).
- Make two recently added ACPI EC messages look better (Scot Doyle).
- Reduce the printk level of a recently added debug message related to
ACPI resources that may become noisy in some cases (Rafael J Wysocki).
- Add a new ACPI backlight blacklist entry for Samsung Series 9
(900X3C/900X3D/900X3E/900X4C/900X4D) laptops where the native backlight
interface doesn't work while the ACPI based one does (Jens Reyer).
- Make the PNP sybsystem's core code use __request_region() followed by
__release_region() instead of __check_region() which then will allow
us to get rid of the latter as it has no more users (Jakub Sitnicki).
- Fix a build breakage and an issue with two __init functions that may be
called after initialization in the s3c cpufreq driver (Arnd Bergmann).
- Make the powernv cpuidle driver read target_residency values for idle
states from a Device Tree (as we have the suitable DT bindings for that
now) and improve the parsing of the powermgmt DT node in that driver
(Preeti U Murthy).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=us59
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.20-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull one more batch of power management and ACPI updates from Rafael Wysocki:
"These are mostly fixes on top of the previously merged recent PM and
ACPI material.
First, one commit that broke the ACPI LPSS (Low-Power Subsystem)
driver on a Dell box is reverted and there are two stable-candidate
fixes for that driver. Another fix cleans up two recently added ACPI
EC messages that look odd and the printk level of a noisy debug
message in the core ACPI resources handling code is reduced.
In addition to that we have two stable-candidate fixes for the s3c
cpufreq driver, two cpuidle powernv driver updates related to Device
Trees and a PNP subsystem cleanup that will allow us to get rid of
some old ugliness going forward. Also there is a new blacklist entry
for the ACPI backlight code.
Specifics:
- Revert a recent ACPI LPSS driver commit that prevented the touchpad
driver from loading on Dell XPS13 (Jarkko Nikula).
- Make the ACPI LPSS driver disable the I2C controllers and deassert
SPI host controllers resets at startup on Intel BayTrail and
Braswell SoCs in case they have been left in wrong states by the
platform firmware which then may casuse fatal controller driver
failures during resume from hibernation (Mika Westerberg).
- Make two recently added ACPI EC messages look better (Scot Doyle).
- Reduce the printk level of a recently added debug message related
to ACPI resources that may become noisy in some cases (Rafael J
Wysocki).
- Add a new ACPI backlight blacklist entry for Samsung Series 9
(900X3C/900X3D/900X3E/900X4C/900X4D) laptops where the native
backlight interface doesn't work while the ACPI based one does
(Jens Reyer).
- Make the PNP sybsystem's core code use __request_region() followed
by __release_region() instead of __check_region() which then will
allow us to get rid of the latter as it has no more users (Jakub
Sitnicki).
- Fix a build breakage and an issue with two __init functions that
may be called after initialization in the s3c cpufreq driver (Arnd
Bergmann).
- Make the powernv cpuidle driver read target_residency values for
idle states from a Device Tree (as we have the suitable DT bindings
for that now) and improve the parsing of the powermgmt DT node in
that driver (Preeti U Murthy)"
* tag 'pm+acpi-3.20-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: powernv: Avoid endianness conversions while parsing DT
cpufreq: s3c: remove last use of resume_clocks callback
cpufreq: s3c: remove incorrect __init annotations
ACPI / LPSS: Deassert resets for SPI host controllers on Braswell
ACPI / LPSS: Always disable I2C host controllers
ACPI / resources: Change pr_info() to pr_debug() for debug information
ACPI / video: Disable native backlight on Samsung Series 9 laptops
cpuidle: powernv: Read target_residency value of idle states from DT if available
Revert "ACPI / LPSS: Remove non-existing clock control from Intel Lynxpoint I2C"
ACPI / EC: Remove non-standard log emphasis
PNP: Switch from __check_region() to __request_region()
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices. Additionaly the framework core underwent a bit of surgery with
two major changes. The boundary between the clock core and clock
providers (e.g clock drivers) is now more well defined with dedicated
provider helper functions. struct clk no longer maps 1:1 with the
hardware clock but is a true per-user cookie which helps us tracker
users of hardware clocks and debug bad behavior. The second major change
is the addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the regulator
framework. Unfortunately these changes to the core created some
breakeage. We think we fixed it all up but for this reason there are
lots of last minute commits trying to undo the damage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zCVK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes contain the usual driver additions,
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices.
Additionally the framework core underwent a bit of surgery with two
major changes:
- The boundary between the clock core and clock providers (e.g clock
drivers) is now more well defined with dedicated provider helper
functions. struct clk no longer maps 1:1 with the hardware clock
but is a true per-user cookie which helps us tracker users of
hardware clocks and debug bad behavior.
- The addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the
regulator framework.
Unfortunately these changes to the core created some breakeage. We
think we fixed it all up but for this reason there are lots of last
minute commits trying to undo the damage"
* tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux: (113 commits)
clk: Only recalculate the rate if needed
Revert "clk: mxs: Fix invalid 32-bit access to frac registers"
clk: qoriq: Add support for the platform PLL
powerpc/corenet: Enable CLK_QORIQ
clk: Replace explicit clk assignment with __clk_hw_set_clk
clk: Add __clk_hw_set_clk helper function
clk: Don't dereference parent clock if is NULL
MIPS: Alchemy: Remove bogus args from alchemy_clk_fgcs_detr
clkdev: Always allocate a struct clk and call __clk_get() w/ CCF
clk: shmobile: div6: Avoid division by zero in .round_rate()
clk: mxs: Fix invalid 32-bit access to frac registers
clk: omap: compile legacy omap3 clocks conditionally
clkdev: Export clk_register_clkdev
clk: Add rate constraints to clocks
clk: remove clk-private.h
pci: xgene: do not use clk-private.h
arm: omap2+ remove dead clock code
clk: Make clk API return per-user struct clk instances
clk: tegra: Define PLLD_DSI and remove dsia(b)_mux
clk: tegra: Add support for the Tegra132 CAR IP block
...
* pnp:
PNP: Switch from __check_region() to __request_region()
* pm-cpuidle:
cpuidle: powernv: Avoid endianness conversions while parsing DT
cpuidle: powernv: Read target_residency value of idle states from DT if available
* pm-cpufreq:
cpufreq: s3c: remove last use of resume_clocks callback
cpufreq: s3c: remove incorrect __init annotations
Pull more thermal managament updates from Zhang Rui:
"Specifics:
- Exynos thermal driver refactoring. Several cleanups, code
optimization, unused symbols removal, and unused feature removal in
Exynos thermal driver. Thanks Lukasz for this effort.
- Exynos thermal driver support to OF thermal. After the code
refactoring, the driver earned the support to OF thermal. Chip
thermal data were moved from driver code to DTS, reducing the code
footprint. Thanks Lukasz for this.
- After receiving the OF thermal support, the exynos thermal driver
now must allow modular build. Thanks Arnd for detecting, reporting
and fixing this.
- Exynos thermal driver support to Exynos 7 SoC. Thanks Abhilash for
this.
- Accurate temperature reporting on Rockchip thermal driver, thanks
to Caesar.
- Fix on how OF thermal enables its zones, thanks Lukasz for fixing.
- Fixes in OF thermal examples under Documentation/. Thanks Srinivas
for fixing"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: exynos: Add TMU support for Exynos7 SoC
dts: Documentation: Add documentation for Exynos7 SoC thermal bindings
cpufreq: exynos: allow modular build
thermal: Fix examples in DT documentation
thermal: exynos: Correct sanity check at exynos_report_trigger() function
thermal: Kconfig: Remove config for not used EXYNOS_THERMAL_CORE
thermal: exynos: Remove exynos_tmu_data.c file
thermal: rockchip: make temperature reporting much more accurate
thermal: exynos: Remove exynos_thermal_common.[c|h] files
thermal: samsung: core: Exynos TMU rework to use device tree for configuration
dts: Documentation: Update exynos-thermal.txt example for Exynos5440
dts: Documentation: Extending documentation entry for exynos-thermal
cpufreq: exynos: Use device tree to determine if cpufreq cooling should be registered
thermal: exynos: Modify exynos thermal code to use device tree for cpu cooling configuration
thermal: exynos: Provide thermal_exynos.h file to be included in device tree files
thermal: exynos: cosmetic: Correct comment format
thermal: of: Enable thermal_zoneX when sensor is correctly added
Commit 32726d2d55 ("ARM: SAMSUNG: Remove legacy clock code")
already removed the callback pointer, but there was one remaining
user:
drivers/cpufreq/s3c24xx-cpufreq.c: In function 's3c_cpufreq_resume_clocks':
drivers/cpufreq/s3c24xx-cpufreq.c:149:14: error: 'struct s3c_cpufreq_info' has no member named 'resume_clocks'
cpu_cur.info->resume_clocks();
^
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 32726d2d55 ("ARM: SAMSUNG: Remove legacy clock code")
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.17+ <stable@vger.kernel.org> # v3.17+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The two functions s3c2416_cpufreq_driver_init and s3c_cpufreq_register
are marked init but are called from a context that might be run after
the __init sections are discarded, as the compiler points out:
WARNING: vmlinux.o(.data+0x1ad9dc): Section mismatch in reference from the variable s3c2416_cpufreq_driver to the function .init.text:s3c2416_cpufreq_driver_init()
WARNING: drivers/built-in.o(.text+0x35b5dc): Section mismatch in reference from the function s3c2410a_cpufreq_add() to the function .init.text:s3c_cpufreq_register()
This removes the __init markings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On Dell Latitude C600 laptop with Pentium 3 850MHz processor, the
speedstep-smi driver sometimes loads and sometimes doesn't load with
"change to state X failed" message.
The hardware sometimes refuses to change frequency and in this case, we
need to retry later. I found out that we need to enable interrupts while
waiting. When we enable interrupts, the hardware blockage that prevents
frequency transition resolves and the transition is possible. With
disabled interrupts, the blockage doesn't resolve (no matter how long do
we wait). The exact reasons for this hardware behavior are unknown.
This patch enables interrupts in the function speedstep_set_state that can
be called with disabled interrupts. However, this function is called with
disabled interrupts only from speedstep_get_freqs, so it shouldn't cause
any problem.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com
Cc: All applicable <stable@vger.kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Rework of the core ACPI resources parsing code to fix issues
in it and make using resource offsets more convenient and
consolidation of some resource-handing code in a couple of places
that have grown analagous data structures and code to cover the
the same gap in the core (Jiang Liu, Thomas Gleixner, Lv Zheng).
- ACPI-based IOAPIC hotplug support on top of the resources handling
rework (Jiang Liu, Yinghai Lu).
- ACPICA update to upstream release 20150204 including an interrupt
handling rework that allows drivers to install raw handlers for
ACPI GPEs which then become entirely responsible for the given GPE
and the ACPICA core code won't touch it (Lv Zheng, David E Box,
Octavian Purdila).
- ACPI EC driver rework to fix several concurrency issues and other
problems related to events handling on top of the ACPICA's new
support for raw GPE handlers (Lv Zheng).
- New ACPI driver for AMD SoCs analogous to the LPSS (Low-Power
Subsystem) driver for Intel chips (Ken Xue).
- Two minor fixes of the ACPI LPSS driver (Heikki Krogerus,
Jarkko Nikula).
- Two new blacklist entries for machines (Samsung 730U3E/740U3E and
510R) where the native backlight interface doesn't work correctly
while the ACPI one does (Hans de Goede).
- Rework of the ACPI processor driver's handling of idle states
to make the code more straightforward and less bloated overall
(Rafael J Wysocki).
- Assorted minor fixes related to ACPI and SFI (Andreas Ruprecht,
Andy Shevchenko, Hanjun Guo, Jan Beulich, Rafael J Wysocki,
Yaowei Bai).
- PCI core power management modification to avoid resuming (some)
runtime-suspended devices during system suspend if they are in
the right states already (Rafael J Wysocki).
- New SFI-based cpufreq driver for Intel platforms using SFI
(Srinidhi Kasagar).
- cpufreq core fixes, cleanups and simplifications (Viresh Kumar,
Doug Anderson, Wolfram Sang).
- SkyLake CPU support and other updates for the intel_pstate driver
(Kristen Carlson Accardi, Srinivas Pandruvada).
- cpufreq-dt driver cleanup (Markus Elfring).
- Init fix for the ARM big.LITTLE cpuidle driver (Sudeep Holla).
- Generic power domains core code fixes and cleanups (Ulf Hansson).
- Operating Performance Points (OPP) core code cleanups and kernel
documentation update (Nishanth Menon).
- New dabugfs interface to make the list of PM QoS constraints
available to user space (Nishanth Menon).
- New devfreq driver for Tegra Activity Monitor (Tomeu Vizoso).
- New devfreq class (devfreq_event) to provide raw utilization data
to devfreq governors (Chanwoo Choi).
- Assorted minor fixes and cleanups related to power management
(Andreas Ruprecht, Krzysztof Kozlowski, Rickard Strandqvist,
Pavel Machek, Todd E Brandt, Wonhong Kwon).
- turbostat updates (Len Brown) and cpupower Makefile improvement
(Sriram Raghunathan).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=zZER
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"We have a few new features this time, including a new SFI-based
cpufreq driver, a new devfreq driver for Tegra Activity Monitor, a new
devfreq class for providing its governors with raw utilization data
and a new ACPI driver for AMD SoCs.
Still, the majority of changes here are reworks of existing code to
make it more straightforward or to prepare it for implementing new
features on top of it. The primary example is the rework of ACPI
resources handling from Jiang Liu, Thomas Gleixner and Lv Zheng with
support for IOAPIC hotplug implemented on top of it, but there is
quite a number of changes of this kind in the cpufreq core, ACPICA,
ACPI EC driver, ACPI processor driver and the generic power domains
core code too.
The most active developer is Viresh Kumar with his cpufreq changes.
Specifics:
- Rework of the core ACPI resources parsing code to fix issues in it
and make using resource offsets more convenient and consolidation
of some resource-handing code in a couple of places that have grown
analagous data structures and code to cover the the same gap in the
core (Jiang Liu, Thomas Gleixner, Lv Zheng).
- ACPI-based IOAPIC hotplug support on top of the resources handling
rework (Jiang Liu, Yinghai Lu).
- ACPICA update to upstream release 20150204 including an interrupt
handling rework that allows drivers to install raw handlers for
ACPI GPEs which then become entirely responsible for the given GPE
and the ACPICA core code won't touch it (Lv Zheng, David E Box,
Octavian Purdila).
- ACPI EC driver rework to fix several concurrency issues and other
problems related to events handling on top of the ACPICA's new
support for raw GPE handlers (Lv Zheng).
- New ACPI driver for AMD SoCs analogous to the LPSS (Low-Power
Subsystem) driver for Intel chips (Ken Xue).
- Two minor fixes of the ACPI LPSS driver (Heikki Krogerus, Jarkko
Nikula).
- Two new blacklist entries for machines (Samsung 730U3E/740U3E and
510R) where the native backlight interface doesn't work correctly
while the ACPI one does (Hans de Goede).
- Rework of the ACPI processor driver's handling of idle states to
make the code more straightforward and less bloated overall (Rafael
J Wysocki).
- Assorted minor fixes related to ACPI and SFI (Andreas Ruprecht,
Andy Shevchenko, Hanjun Guo, Jan Beulich, Rafael J Wysocki, Yaowei
Bai).
- PCI core power management modification to avoid resuming (some)
runtime-suspended devices during system suspend if they are in the
right states already (Rafael J Wysocki).
- New SFI-based cpufreq driver for Intel platforms using SFI
(Srinidhi Kasagar).
- cpufreq core fixes, cleanups and simplifications (Viresh Kumar,
Doug Anderson, Wolfram Sang).
- SkyLake CPU support and other updates for the intel_pstate driver
(Kristen Carlson Accardi, Srinivas Pandruvada).
- cpufreq-dt driver cleanup (Markus Elfring).
- Init fix for the ARM big.LITTLE cpuidle driver (Sudeep Holla).
- Generic power domains core code fixes and cleanups (Ulf Hansson).
- Operating Performance Points (OPP) core code cleanups and kernel
documentation update (Nishanth Menon).
- New dabugfs interface to make the list of PM QoS constraints
available to user space (Nishanth Menon).
- New devfreq driver for Tegra Activity Monitor (Tomeu Vizoso).
- New devfreq class (devfreq_event) to provide raw utilization data
to devfreq governors (Chanwoo Choi).
- Assorted minor fixes and cleanups related to power management
(Andreas Ruprecht, Krzysztof Kozlowski, Rickard Strandqvist, Pavel
Machek, Todd E Brandt, Wonhong Kwon).
- turbostat updates (Len Brown) and cpupower Makefile improvement
(Sriram Raghunathan)"
* tag 'pm+acpi-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (151 commits)
tools/power turbostat: relax dependency on APERF_MSR
tools/power turbostat: relax dependency on invariant TSC
Merge branch 'pci/host-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci into acpi-resources
tools/power turbostat: decode MSR_*_PERF_LIMIT_REASONS
tools/power turbostat: relax dependency on root permission
ACPI / video: Add disable_native_backlight quirk for Samsung 510R
ACPI / PM: Remove unneeded nested #ifdef
USB / PM: Remove unneeded #ifdef and associated dead code
intel_pstate: provide option to only use intel_pstate with HWP
ACPI / EC: Add GPE reference counting debugging messages
ACPI / EC: Add query flushing support
ACPI / EC: Refine command storm prevention support
ACPI / EC: Add command flushing support.
ACPI / EC: Introduce STARTED/STOPPED flags to replace BLOCKED flag
ACPI: add AMD ACPI2Platform device support for x86 system
ACPI / table: remove duplicate NULL check for the handler of acpi_table_parse()
ACPI / EC: Update revision due to raw handler mode.
ACPI / EC: Reduce ec_poll() by referencing the last register access timestamp.
ACPI / EC: Fix several GPE handling issues by deploying ACPI_GPE_DISPATCH_RAW_HANDLER mode.
ACPICA: Events: Enable APIs to allow interrupt/polling adaptive request based GPE handling model
...
Pull SFI-based cpufreq driver for v3.20 from Len Brown.
* 'sfi' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
cpufreq: Add SFI based cpufreq driver support
SFI: fix compiler warnings
Allow users the option to disable the driver for any hardware
which does not support HWP.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq_cooling_unregister() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To make code more readable and less error prone, lets create a helper macro for
iterating over all available governors.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To make code more readable and less error prone, lets create a helper macro for
iterating over all active policies.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When cpufreq is disabled, the per-cpu variable would have been set to
NULL. Remove this unnecessary check.
[ Changelog from Saravana Kannan. ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In __cpufreq_remove_dev_finish(), per-cpu 'cpufreq_cpu_data' needs
to be cleared before calling kobject_put(&policy->kobj) and under
cpufreq_driver_lock. Otherwise, if someone else calls cpufreq_cpu_get()
in parallel with it, they can obtain a non-NULL policy from that after
kobject_put(&policy->kobj) was executed.
Consider this case:
Thread A Thread B
cpufreq_cpu_get()
acquire cpufreq_driver_lock
read-per-cpu cpufreq_cpu_data
kobject_put(&policy->kobj);
kobject_get(&policy->kobj);
...
per_cpu(&cpufreq_cpu_data, cpu) = NULL
And this will result in a warning like this one:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 4 at include/linux/kref.h:47
kobject_get+0x41/0x50()
Modules linked in: acpi_cpufreq(+) nfsd auth_rpcgss nfs_acl
lockd grace sunrpc xfs libcrc32c sd_mod ixgbe igb mdio ahci hwmon
...
Call Trace:
[<ffffffff81661b14>] dump_stack+0x46/0x58
[<ffffffff81072b61>] warn_slowpath_common+0x81/0xa0
[<ffffffff81072c7a>] warn_slowpath_null+0x1a/0x20
[<ffffffff812e16d1>] kobject_get+0x41/0x50
[<ffffffff815262a5>] cpufreq_cpu_get+0x75/0xc0
[<ffffffff81527c3e>] cpufreq_update_policy+0x2e/0x1f0
[<ffffffff810b8cb2>] ? up+0x32/0x50
[<ffffffff81381aa9>] ? acpi_ns_get_node+0xcb/0xf2
[<ffffffff81381efd>] ? acpi_evaluate_object+0x22c/0x252
[<ffffffff813824f6>] ? acpi_get_handle+0x95/0xc0
[<ffffffff81360967>] ? acpi_has_method+0x25/0x40
[<ffffffff81391e08>] acpi_processor_ppc_has_changed+0x77/0x82
[<ffffffff81089566>] ? move_linked_works+0x66/0x90
[<ffffffff8138e8ed>] acpi_processor_notify+0x58/0xe7
[<ffffffff8137410c>] acpi_ev_notify_dispatch+0x44/0x5c
[<ffffffff8135f293>] acpi_os_execute_deferred+0x15/0x22
[<ffffffff8108c910>] process_one_work+0x160/0x410
[<ffffffff8108d05b>] worker_thread+0x11b/0x520
[<ffffffff8108cf40>] ? rescuer_thread+0x380/0x380
[<ffffffff81092421>] kthread+0xe1/0x100
[<ffffffff81092340>] ? kthread_create_on_node+0x1b0/0x1b0
[<ffffffff81669ebc>] ret_from_fork+0x7c/0xb0
[<ffffffff81092340>] ? kthread_create_on_node+0x1b0/0x1b0
---[ end trace 89e66eb9795efdf7 ]---
The actual code flow is as follows:
Thread A: Workqueue: kacpi_notify
acpi_processor_notify()
acpi_processor_ppc_has_changed()
cpufreq_update_policy()
cpufreq_cpu_get()
kobject_get()
Thread B: xenbus_thread()
xenbus_thread()
msg->u.watch.handle->callback()
handle_vcpu_hotplug_event()
vcpu_hotplug()
cpu_down()
__cpu_notify(CPU_POST_DEAD..)
cpufreq_cpu_callback()
__cpufreq_remove_dev_finish()
cpufreq_policy_put_kobj()
kobject_put()
cpufreq_cpu_get() gets the policy from per-cpu variable cpufreq_cpu_data
under cpufreq_driver_lock, and once it gets a valid policy it expects it
to not be freed until cpufreq_cpu_put() is called.
But the race happens when another thread puts the kobject first and updates
cpufreq_cpu_data before or later. And so the first thread gets a valid policy
structure and before it does kobject_get() on it, the second one has already
done kobject_put().
Fix this by setting cpufreq_cpu_data to NULL before putting the kobject and that
too under locks.
Reported-by: Ethan Zhao <ethan.zhao@oracle.com>
Reported-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The exynos cpufreq driver code recently gained a dependency on the
cooling code, which may be a loadable module. This breaks an ARM
allmodconfig build:
drivers/built-in.o: In function `exynos_cpufreq_probe':
:(.text+0x1748e8): undefined reference to `of_cpufreq_cooling_register'
To avoid this problem, change cpufreq Kconfig to allow the drivers
to be loadable modules as well and enforce a dependency on the
thermal module.
This change, in order to allow module builds on this cpufreq
driver, properly constructs the driver into a single module,
instead of several modules. The change also keeps the proper
platform dependency, and therefore, it wont load in platforms
that are not supposed to be loaded. The user will be able to
build the support for all platforms, or select which platforms
(s)he wants (as originally), except that now it can be a module,
instead.
Besides, it will still keep the driver only on those configs
that expect it to be on. And it won't compile/load on platforms
that it is not supposed to. It brings the config ARM_EXYNOS_CPU_FREQ_BOOST_SW
closer to this driver, so it looks better in the menuconfig.
We intentionally change ARM_EXYNOS5440_CPUFREQ to be tristate too, to
avoid future troubles.
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-pm@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Fixes: e725d26c48 ("cpufreq: exynos: Use device tree to determine if cpufreq cooling should be registered")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
If the user has requested an override of the min_perf_pct via
sysfs, then it should be restored whenever policy is updated,
such as on resume. Take the max of whatever the user requested
and whatever the policy is.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When thermal or other subsystem requests to change the policy,
use that irrepective of whether cpufreq policy is PERFORMANCE or
not. Without this change, when thermal subsystem passive policy wants
to reduce performance, it still runs at 100%.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a sysfs interface to display the total number of supported
pstates. This value is independent of whether turbo has been
enabled or disabled.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds "turbo_pct" to the intel_pstate sysfs interface.
turbo_pct will display the percentage of the total supported
pstates that are in the turbo range. This value is independent
of whether turbo has been disabled or not.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With thermal subsystem rework it is necessary to tune current cpufreq code
to use cpu frequency change as a potential cooling device.
Now the cpu cooling device is registered only when proper nodes and properties
are available in device tree. Lack of them, however, will not prevent
cpufreq for normal operation.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There is no possibility of any race on updating last_index, trans_table or
total_trans as these are updated only by cpufreq_stat_notifier_trans() which
will be called sequentially.
The only place where locking is still relevant is: cpufreq_stats_update(), which
updates time_in_state and last_time. This can be called by two thread in
parallel, that may result in races.
The two threads being:
- sysfs read of time_in_state
- and frequency transition that calls cpufreq_stat_notifier_trans().
Remove locking from the first case mentioned above.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We need to call cpufreq_stats_update() to update 'time_in_state' for the last
frequency. This is achieved by calling it from cpufreq_stat_notifier_trans(),
which is called after frequency transition.
But if we detect that the cpu's frequency haven't really changed and its a false
POSTCHANGE notification, we don't really need to update time_in_state.
It wouldn't cause any harm in calling cpufreq_stats_update() but we can avoid
calling it here and call it when the frequency really changes. The result will
be the same but more efficient.
Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_stats_update() updates time_in_state and nothing else. It should ideally
be updated only in two cases:
- User requested for the current value of time_in_state.
- We have switched states and so need to update time for the last state.
Currently, we are also doing this while user asks for the transition table of
frequencies. It wouldn't do any harm, but no good as well. Its useless here.
Remove it.
Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
'time_in_state' can't be NULL if 'stats' is valid. These are allocated together
and only if time_in_state is allocated successfully, we update policy->stats.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Userspace is free to read value of any file from cpufreq/stats directory once
they are created. __cpufreq_stats_create_table() is creating the sysfs files
first and then allocating resources for them. Though it would be quite difficult
to trigger the racy situation here, but for the sake of keeping sensible code
lets create sysfs entries only after we are ready to go.
This also does some makeup to the routine to make it look better.
Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CPUFREQ_UPDATE_POLICY_CPU notifications were used only from cpufreq-stats which
doesn't use it anymore. Remove them.
This also decrements values of other notification macros defined after
CPUFREQ_UPDATE_POLICY_CPU by 1 to remove gaps. Hopefully all users are using
macro's instead of direct numbers and so they wouldn't break as macro values are
changed now.
Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
'cpu' field of struct cpufreq_stats isn't used anymore and so can be dropped.
This change makes cpufreq_stats_update_policy_cpu() empty and so that is removed
as well.
Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
'last_cpu' was used only from cpufreq-stats and isn't used anymore. Get rid of
it.
Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently we name objects of 'struct cpufreq_stats' as 'stat' and 'stats'.
Use 'stats' to make it consistent.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
All CPUs sharing a cpufreq policy share stats too. For this reason,
add a stats pointer to struct cpufreq_policy and drop per-CPU variable
cpufreq_stats_table used for accessing cpufreq stats so as to reduce
code complexity.
Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is better to pass a struct cpufreq_stats pointer to cpufreq_stats_update()
instead of a CPU number, because that's all it needs.
Even if we pass a cpu number to cpufreq_stats_update(), it reads the per-cpu
variable to get 'stats' out of it. So we are doing these operations
unnecessarily:
- First getting the cpu number to pass to cpufreq_stats_update(), stat->cpu.
- And then getting stats from the cpu, per_cpu(cpufreq_stats_table, cpu).
Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
While we allocate stats, we do need to check if freq-table is present
or not as we need to use it then. But while freeing stats, all we need
to know is if stats holds a valid pointer value. There is no use of
testing if cpufreq table is present or not.
Don't check it.
Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
'cur_time' is defined in the first line and is then assigned a value
in the next line. Initialize it while defining it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It was never used, but is there since the first commit. Remove it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
__cpufreq_stats_create_table() is called from:
- cpufreq notifier on creation of a new policy. Stats will always be
NULL here.
- cpufreq_stats_init() for all CPUs as cpufreq-stats might have been
initialized after cpufreq driver. For any policy, 'stats' will be
NULL for the first CPU only and will be valid for all other CPUs
managed by the same policy.
While we return for other CPUs, we don't return the right error value.
It's not that we would fail with -EBUSY. But generally, this is what
these return values mean:
- EBUSY: we are busy right now, try again. And the retry attempt might
be immediate.
- EEXIST: We already have what you are trying to create and there is no
need to create it again, and so no more tries are required.
Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The MODULE_DESCRIPTION() string is just too long and then is broken into
multiple lines just to make checkpatch happy.
Rewrite it to make it more precise.
Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We need to initialize completion and work only on policy allocation and not
really on the policy restore side and so we better move this piece of code to
cpufreq_policy_alloc().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CPUFREQ_STICKY flag is set by drivers which don't want to get unregistered
even if cpufreq-core isn't able to initialize policy for any CPU.
When this flag isn't set, we try to unregister the driver. To find out
which CPUs are registered and which are not, we try to check per_cpu
cpufreq_cpu_data for all CPUs. Because we have a list of valid policies
available now, we better check if the list is empty or not instead of
the 'for' loop. That will be much more efficient.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These variables are just used within adjust_jiffies() and so must be
local to it. Also there is no need of a dummy routine for CONFIG_SMP
case as we can take care of all that with help of macros in the same
routine. It doesn't look that ugly.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We just need to check if a 'policy' is already present for the cpu we are
adding. We don't need to take all the locks and do kobject usage updates. Use
the light-weight cpufreq_cpu_get_raw() routine instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is no need of this separate variable, use 'policy' instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These are messing up more than the benefit they provide. It isn't
a lot of code anyway, that we will compile without them.
Kill them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We should first check if a cpufreq driver is already registered or not
before updating driver_data->flags.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is no point finding out the 'policy' again within __cpufreq_get()
when all the callers already have it. Just make them pass policy instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is no point finding out the 'policy' again within cpufreq_out_of_sync()
when all the callers already have it. Just make them pass policy instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Either we can be setpolicy or target type, nothing else. And so the
else part of setpolicy will automatically be of has_target() type.
And so we don't need to check it again.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove unnecessary from find_governor's name.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are two 'if' blocks here, checking for !cpufreq_driver->setpolicy and
has_target(). Both are actually doing the same thing, merge them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
No need of an unnecessary line break.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We can live without it and so we should.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It doesn't make any sense at all and is a leftover of some earlier commit.
Remove it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We should stop cpufreq governors when we shut down the system. If we
don't do this, we can end up with this deadlock:
1. cpufreq governor may be running on a CPU other than CPU0.
2. In machine_restart() we call smp_send_stop() which stops CPUs.
If one of these CPUs was actively running a cpufreq governor
then it may have the mutex / spinlock needed to access the main
PMIC in the system (perhaps over I2C)
3. If a machine needs access to the main PMIC in order to shutdown
then it will never get it since the mutex was lost when the other
CPU stopped.
4. We'll hang (possibly eventually hitting the hard lockup detector).
Let's avoid the problem by stopping the cpufreq governor at shutdown,
which is a sensible thing to do anyway.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This platform_driver does not need to set an owner, it will be
populated by the driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull RCU updates from Paul E. McKenney:
- Documentation updates.
- Miscellaneous fixes.
- Preemptible-RCU fixes, including fixing an old bug in the
interaction of RCU priority boosting and CPU hotplug.
- SRCU updates.
- RCU CPU stall-warning updates.
- RCU torture-test updates.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Freescale introduced new ARM-based socs which using the compatible
clock IP block with PowerPC-based socs'. So this driver can be used
on both platforms.
Updated relevant descriptions and renamed this driver to better
represent its meaning and keep the function of driver untouched.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
SRCU is not necessary to be compiled by default in all cases. For tinification
efforts not compiling SRCU unless necessary is desirable.
The current patch tries to make compiling SRCU optional by introducing a new
Kconfig option CONFIG_SRCU which is selected when any of the components making
use of SRCU are selected.
If we do not select CONFIG_SRCU, srcu.o will not be compiled at all.
text data bss dec hex filename
2007 0 0 2007 7d7 kernel/rcu/srcu.o
Size of arch/powerpc/boot/zImage changes from
text data bss dec hex filename
831552 64180 23944 919676 e087c arch/powerpc/boot/zImage : before
829504 64180 23952 917636 e0084 arch/powerpc/boot/zImage : after
so the savings are about ~2000 bytes.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
CC: Josh Triplett <josh@joshtriplett.org>
CC: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
[ paulmck: resolve conflict due to removal of arch/ia64/kvm/Kconfig. ]
* pm-cpufreq:
cpufreq: fix a NULL pointer dereference in __cpufreq_governor()
cpufreq-dt: defer probing if OPP table is not ready
* pm-cpuidle:
cpuidle / ACPI: remove unused CPUIDLE_FLAG_TIME_INVALID
cpuidle: ladder: Better idle duration measurement without using CPUIDLE_FLAG_TIME_INVALID
cpuidle: menu: Better idle duration measurement without using CPUIDLE_FLAG_TIME_INVALID
This adds the SFI based cpu freq driver for some of the Intel's
Silvermont based Atom architectures like Z34xx and Z35xx.
Signed-off-by: Rudramuni, Vishwesh M <vishwesh.m.rudramuni@intel.com>
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Len Brown <len.brown@intel.com>
I'm leaving Red Hat at the end of December 2014, so remove all
references to my soon-to-be-dead address.
(There are some references left in the tree, that need additional
changes, I'll send those through the AGP maintainers).
Signed-off-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
cpufreq-dt driver supports mode when OPP table is provided by platform
code and not device tree. However on certain platforms code that fills
OPP table may run after cpufreq driver tries to initialize, so let's
report -EPROBE_DEFER if we do not find any entires in OPP table for the
CPU.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Add a few comments in the code which calculates busyness to
clarify parts of the algorithm.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To force loading on Oracle Sun X86 servers, provide one kernel command line
parameter
intel_pstate = force
For those who are aware of the risk of no power capping capabily working
and try to get better performance with this driver.
Signed-off-by: Ethan Zhao <ethan.zhao@oracle.com>
Tested-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Reviewed-by: Linda Knippers <linda.knippers@hp.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Oracle Sun X86 servers have dynamic power capping capability that works via
ACPI _PPC method etc, so skip loading this driver if Sun server has ACPI _PPC
enabled.
Signed-off-by: Ethan Zhao <ethan.zhao@oracle.com>
Tested-by: Linda Knippers <linda.knippers@hp.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
OPP layer now supports freeing of OPPs and we should free them once they aren't
useful anymore.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
OPP layer now supports freeing of OPPs and we should free them once they aren't
useful anymore.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
OPP layer now supports freeing of OPPs and we should free them once they aren't
useful anymore.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
OPP layer now supports freeing of OPPs and we should free them once they aren't
useful anymore.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently we are calling of_cpufreq_cooling_register() from ->init() callback.
At this point of time cpufreq driver's policy isn't completely ready to be used
as few of its fields/structure/pointers aren't yet initialized.
Because of_cpufreq_cooling_register() tries to access policy with help of
cpufreq_cpu_get() and then tries to get freq-table as well, these calls fail.
To fix this, register the cooling device after the policy is ready to be used.
And the right callback for it is the newly added ->ready() one.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Eduardo Valentin <edubezval@gmail.com>
Tested-by: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently there is no callback for cpufreq drivers which is called once the
policy is ready to be used. There are some requirements where such a callback is
required.
One of them is registering a cooling device with the help of
of_cpufreq_cooling_register(). This routine tries to get 'struct cpufreq_policy'
for CPUs which isn't yet initialed at the time ->init() is called and so we face
issues while registering the cooling device.
Because we can't register cooling device from ->init(), we need a callback that
is called after the policy is ready to be used and hence we introduce ->ready()
callback.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Eduardo Valentin <edubezval@gmail.com>
Tested-by: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The second parameter of of_cpufreq_cooling_register() should be the CPUs to
which the frequency constraint will apply. As the cpufreq-dt driver now supports
platforms with multiple 'struct cpufreq_policy' instances (i.e. > 1 clock
domains for CPUs), passing 'cpu_present_mask' isn't correct anymore. As every
policy will have a set of CPUs and that may not be equal to 'cpu_present_mask'
always.
So, pass only mask of CPUs which are controlled by current policy.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Eduardo Valentin <edubezval@gmail.com>
Tested-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add ability for PXA2xx CPUFreq to be compiled as a module or not at all.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Do it before it's assigned to cpufreq_cpu_data, otherwise when a driver
tries to get the cpu frequency during initialization the policy kobj is
referenced and we get this warning:
------------[ cut here ]------------
WARNING: CPU: 1 PID: 64 at include/linux/kref.h:47 kobject_get+0x64/0x70()
Modules linked in:
CPU: 1 PID: 64 Comm: irq/77-tegra-ac Not tainted 3.18.0-rc4-next-20141114ccu-00050-g3eff942 #326
[<c0016fac>] (unwind_backtrace) from [<c001272c>] (show_stack+0x10/0x14)
[<c001272c>] (show_stack) from [<c06085d8>] (dump_stack+0x98/0xd8)
[<c06085d8>] (dump_stack) from [<c002892c>] (warn_slowpath_common+0x84/0xb4)
[<c002892c>] (warn_slowpath_common) from [<c00289f8>] (warn_slowpath_null+0x1c/0x24)
[<c00289f8>] (warn_slowpath_null) from [<c0220290>] (kobject_get+0x64/0x70)
[<c0220290>] (kobject_get) from [<c03e944c>] (cpufreq_cpu_get+0x88/0xc8)
[<c03e944c>] (cpufreq_cpu_get) from [<c03e9500>] (cpufreq_get+0xc/0x64)
[<c03e9500>] (cpufreq_get) from [<c0285288>] (actmon_thread_isr+0x134/0x198)
[<c0285288>] (actmon_thread_isr) from [<c0069008>] (irq_thread_fn+0x1c/0x40)
[<c0069008>] (irq_thread_fn) from [<c0069324>] (irq_thread+0x134/0x174)
[<c0069324>] (irq_thread) from [<c0040290>] (kthread+0xdc/0xf4)
[<c0040290>] (kthread) from [<c000f4b8>] (ret_from_fork+0x14/0x3c)
---[ end trace b7bd64a81b340c59 ]---
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently the error message is needlessly splitted across two lines.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
CPUFreq driver's Kconfig entries are added in Kconfig.<arch> files and they are
all included from the main Kconfig file using a menu entry. This creates another
level of (unnecessary) hierarchy within the menuconfig entries.
The problem occurs when there are drivers usable across architectures. Either
their config entry is duplicated in all the supported architectures or is put
into the main Kconfig entry. With the later one, we have menuconfig entries for
drivers at two levels then.
Fix these issues by getting rid of another level of menuconfig hierarchy and
populate all drivers within the main cpufreq menu. To clearly distinguish where
the drivers start from, also add a comment that will appear in menuconfig.
Reported-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The pcc-cpufreq driver is not automatically loaded on systems where
the platform's power management setting requires this driver.
Instead, on those systems no CPU frequency driver is registered and
active.
Make the autoloading matching criteria for loading the pcc-cpufreq
driver the same as done in acpi-cpufreq by commit c655affbd5
("ACPI / cpufreq: Add ACPI processor device IDs to acpi-cpufreq").
x86 CPU frequency drivers are now typically autoloaded by specifying
MODULE_DEVICE_TABLE entries and x86cpu model specific matching.
But pcc-cpufreq was omitted when acpi-cpufreq and other drivers were
changed to use this approach.
Both acpi-cpufreq and pcc-cpufreq depend on a distinct and mutually
exclusive set of ACPI methods which are not directly tied to specific
processor model numbers. Both of these drivers have init routines
which look for their required ACPI methods. As a result, only the
appropriate driver registers as the cpu frequency driver and the other
one ends up being unloaded.
Tested on various systems where acpi-cpufreq, intel_pstate, and
pcc-cpufreq are the expected cpu frequency drivers.
Signed-off-by: Lenny Szubowicz <lszubowi@redhat.com>
Signed-off-by: Joseph Szczypek <joseph.szczypek@hp.com>
Reported-by: Trinh Dao <trinh.dao@hp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add BDW-H to the list of supported processors.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support of Hardware Managed Performance States (HWP) described in Volume 3
section 14.4 of the SDM.
With HWP enbaled intel_pstate will no longer be responsible for selecting P
states for the processor. intel_pstate will continue to register to
the cpufreq core as the scaling driver for CPUs implementing
HWP. In HWP mode intel_pstate provides three functions reporting
frequency to the cpufreq core, support for the set_policy() interface
from the core and maintaining the intel_pstate sysfs interface in
/sys/devices/system/cpu/intel_pstate. User preferences expressed via
the set_policy() interface or the sysfs interface are forwared to the
CPU via the HWP MSR interface.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When the user space tries to set scaling_(max|min)_freq through
sysfs, the cpufreq_set_policy() asks other driver's opinions
for the max/min frequencies. Some device drivers, like Tegra
CPU EDP which is not upstreamed yet though, may constrain the
CPU maximum frequency dynamically because of board design.
So if the user space access happens and some driver is capping
the cpu frequency at the same time, the user_policy->(max|min)
is overridden by the capped value, and that's not expected by
the user space. And if the user space is not invoked again,
the CPU will always be capped by the user_policy->(max|min)
even no drivers limit the CPU frequency any more.
This patch preserves the user specified min/max settings, so that
every time the cpufreq policy is updated, the new max/min can
be re-evaluated correctly based on the user's expection and
the present device drivers' status.
Signed-off-by: Vince Hsu <vinceh@nvidia.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When resuming from s2ram on an SMP system without cpufreq operating
points (e.g. there's no "operating-points" property for the CPU node in
DT, or the platform doesn't use DT yet), the kernel crashes when
bringing CPU 1 online:
Enabling non-boot CPUs ...
CPU1: Booted secondary processor
Unable to handle kernel NULL pointer dereference at virtual address 0000003c
pgd = ee5e6b00
[0000003c] *pgd=6e579003, *pmd=6e588003, *pte=00000000
Internal error: Oops: a07 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1246 Comm: s2ram Tainted: G W 3.18.0-rc3-koelsch-01614-g0377af242bb175c8-dirty #589
task: eeec5240 ti: ee704000 task.ti: ee704000
PC is at __cpufreq_add_dev.isra.24+0x24c/0x77c
LR is at __cpufreq_add_dev.isra.24+0x244/0x77c
pc : [<c0298efc>] lr : [<c0298ef4>] psr: 60000153
sp : ee705d48 ip : ee705d48 fp : ee705d84
r10: c04e0450 r9 : 00000000 r8 : 00000001
r7 : c05426a8 r6 : 00000001 r5 : 00000001 r4 : 00000000
r3 : 00000000 r2 : 00000000 r1 : 20000153 r0 : c0542734
Verify that policy is not NULL before dereferencing it to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 8414809c6a (cpufreq: Preserve policy structure across suspend/resume)
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In error cases regulator_get_voltage() returns a negative value.
So take care of it.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
During test of new DT OPPs it's very helpful to print the matching
OPP in case of frequency change. So it will be easier to find frequency
rounding issues in the dts file.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>