According to our Gadget Framework API documentation,
->set_halt() *must* return -EAGAIN if we have pending
transfers (on either direction) or FIFO isn't empty (on
TX endpoints).
Fix this bug so that the mass storage gadget can be used
without stall=0 parameter.
This patch should be backported to all kernels since v3.2.
Cc: <stable@vger.kernel.org> # v3.2+
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc3_gadget_ep0_set_halt() will be called without
locks held in some cases, so we must hold the lock
on our own. While at that, also add a version without
locks to be called in certain conditions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Those functions are only using within debugging
messages, grouping them into debug.h makes sense.
While at that, also add missing multiple inclusion
guard.
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 388e5c5 (usb: dwc3: remove dwc3 dependency
on host AND gadget.) created the possibility for
host-only and peripheral-only dwc3 builds but
left a possible randconfig build error when host-only
builds are selected.
Cc: <stable@vger.kernel.org> # v3.8+
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This function will be used during hibernation to get
the current link state. It will be needed at least
for Hibernation support.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is a Linux-only driver which makes use
of GPL-only symbols. It makes no sense to
maintain Dual BSD/GPL licensing for this driver.
Considering that the amount of work to use this
driver in any different operating system would likely
be as large as developing the driver from scratch and
considering that we depend on GPL-only symbols, we
will switch over to a GPL v2-only license.
Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
set_halt for ep0 is called to stall a deferred control responses by the
gadget. We already have a function to stall default control endpoint.
This patch points set_halt for ep0 to the already available function.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Michel Sanches <michel.sanches@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds definitions for some new registers that have been
added to later versions of the controller, up to v2.10a.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here are the changes for v3.4 merge window.
It includes a new glue layer for Samsung's Exynos platform, a simplification of
memory management on DWC3 driver by using dev_xxx functions, a few
optimizations to IRQ handling by dropping memcpy() and using bitshifts, a fix
for TI's OMAP5430 TX Fifo Allocation, two fixes on USB2 test mode
implementation (one on debugfs and one on ep0), and several minor changes such
as whitespace cleanups, simplification of a few parts of the code, decreasing a
long delay to something a bit saner, dropping a header which was included twice
and so on.
The highlight on this merge is the support for Samsung's Exynos platform,
increasing the number of different users for this driver to three.
Note that Samsung Exynos glue layer will only compile on platforms which
provide implementation for the clk API for now. Once Samsung supports
pm_runtime, that limitation can be dropped from the Makefile.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPUJ2bAAoJEIaOsuA1yqREwOgP/2bG6rvPBMlGmXvvR40HNUXJ
jXzkXcrTBrO172Fxl2P+mAgNFggMURrOdiyXwl7+2Ib0NM7sS9jwikuxos8DwuQv
Ci0GgJtQySORIl5Sw29uB1W65aV2ieNBh/fN/52LwVOQYITt89GYK1DsRUWRN2V/
0bw3OepckiAFN5gWRykIYIUXZs8DQa+L1qYc6fexZk7zZ+XrjdNba8RzGzsyUelD
BB0eOj4E2Mda6Yp7kyiBRuTXVAUChNa5J0iCvXSnR8l2wppfXlmD2UD4Sfo/yxd5
q25/rm1e1A4iKcPjSkhzTayQKrLWEgCxZK69sZXlEPG9qhA3iMjWDNBvEy6cV4bc
bFFjwXAObX+bm+QDYqcD66iUZTPzEW149W/e5B7+XGk09NcCs/wqoA1jEgCLEHnv
3rsG0RvsgtMdwmBYpO8zrhJPTFa6NAq9Qc4nLj3WefXP9Vkl5gpfneIcgYKB6x0q
LHRQsLHBWl/hXClWAPflDJaGQqEt6hjkA3IqV03yTlMNuYxDNJy931J6Cz9a9Lu5
Gr2By/bHVcADmt8WzituQsnLvQIzLLGl0U0lKpdl24I52roqMkZVj7XaWDojLVSq
HZnbk+c3PdEXVIDNCz1QnCY/QojEhKkeR23LP3YD8L9KxcOu8DNyL1RKdYqx3Cnv
vrqerutPusT6kGvaRQIk
=4Z2+
-----END PGP SIGNATURE-----
Merge tag 'dwc3-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: dwc3: changes for v3.4 merge window
Here are the changes for v3.4 merge window.
It includes a new glue layer for Samsung's Exynos platform, a simplification of
memory management on DWC3 driver by using dev_xxx functions, a few
optimizations to IRQ handling by dropping memcpy() and using bitshifts, a fix
for TI's OMAP5430 TX Fifo Allocation, two fixes on USB2 test mode
implementation (one on debugfs and one on ep0), and several minor changes such
as whitespace cleanups, simplification of a few parts of the code, decreasing a
long delay to something a bit saner, dropping a header which was included twice
and so on.
The highlight on this merge is the support for Samsung's Exynos platform,
increasing the number of different users for this driver to three.
Note that Samsung Exynos glue layer will only compile on platforms which
provide implementation for the clk API for now. Once Samsung supports
pm_runtime, that limitation can be dropped from the Makefile.
Conflicts:
drivers/usb/dwc3/gadget.c
those routines have everything we need to map/unmap
USB requests and it's better to use them.
In order to achieve that, we had to add a simple
change on how we allocate and use our setup buffer;
we cannot allocate it from coherent anymore otherwise
the generic map/unmap routines won't be able to easily
know that the GetStatus request already has a DMA
address.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Most link changes will, of course, happen with
the help of a matching host HW, but in some cases
we might want to debug very low level details about
the link and exposing this to debugfs sounds like
a good plan.
This is a preparation for such setup.
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are some situations were we might need to
enable USB Test Modes without having access to a
Host stack. In such situations we cannot rely
solely on USB Control Messages to enable test
features.
For those cases, we will also allow test mode
to be enabled via debugfs and this patch is a
preparation for that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of special functions and shortcuts for sending our internal
answers to the host we started doing what the gadget does and used the
public API for this. Since we only were using a few fields the
usb_request was enough. Later added the list handling in order to
synchronize the host / gadget events and now we require to have the
dwc3_request struct around our usb_request or else we touch memory that
does not belong to us. So this patch does this.
Reported-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There were a few coding style issues with this driver
which are now fixed:
drivers/usb/dwc3/debugfs.c:48: WARNING: Use #include \
<linux/uaccess.h> instead of <asm/uaccess.h>
drivers/usb/dwc3/debugfs.c:484: ERROR: space required \
before the open brace '{'
drivers/usb/dwc3/ep0.c:261: WARNING: line over 80 characters
drivers/usb/dwc3/ep0.c:287: WARNING: suspect code indent \
for conditional statements (16, 23)
drivers/usb/dwc3/gadget.c:749: WARNING: line over 80 characters
drivers/usb/dwc3/gadget.c:1267: WARNING: line over 80 characters
drivers/usb/dwc3/gadget.h:116: WARNING: line over 80 characters
drivers/usb/dwc3/io.h:42: WARNING: Use #include \
<linux/io.h> instead of <asm/io.h>
Signed-off-by: Felipe Balbi <balbi@ti.com>
our parameter structures need to be written to
HW, so instead of assuming little endian, we
convert those into bit shifts.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some people think that this line is not compatible with the GPL. The
statement was required due to the Buenos Aires Convention and is now
deprecated. I remove it because it is said that it is pointless nowdays.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix build error when CONFIG_USB_GADGET_DWC3 is not enabled:
ERROR: "dwc3_send_gadget_ep_cmd" [drivers/usb/dwc3/dwc3.ko] undefined!
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The DesignWare USB3 is a highly
configurable IP Core which can be
instantiated as Dual-Role Device (DRD),
Peripheral Only and Host Only (XHCI)
configurations.
Several other parameters can be configured
like amount of FIFO space, amount of TX and
RX endpoints, amount of Host Interrupters,
etc.
The current driver has been validated with
a virtual model of version 1.73a of that core
and with an FPGA burned with version 1.83a
of the DRD core. We have support for PCIe
bus, which is used on FPGA prototyping, and
for the OMAP5, more adaptation (or glue)
layers can be easily added and the driver
is half prepared to handle any possible
configuration the HW engineer has chosen
considering we have the information on
one of the GHWPARAMS registers to do
runtime checking of certain features.
More runtime checks can, and should, be added
in order to make this driver even more flexible
with regards to number of endpoints, FIFO sizes,
transfer types, etc.
While this supports only the device side, for
now, we will add support for Host side (xHCI -
see the updated series Sebastian has sent [1])
and OTG after we have it all stabilized.
[1] http://marc.info/?l=linux-usb&m=131341992020339&w=2
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Felipe Balbi