Previously, we requested that drivers pass ecc.size and ecc.bytes when
using NAND_ECC_SOFT_BCH. However, a driver is likely to only know the ECC
strength required for its NAND, so each driver would need to perform a
strength-to-bytes calculation.
Avoid duplicating this calculation in each driver by asking drivers to
pass ecc.size and ecc.strength so that the strength-to-bytes calculation
need only be implemented once.
This reverts/generalizes this commit:
mtd: nand: Base BCH ECC bytes on required strength
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The recently added mtd_mmap_capabilities can be used from loadable
modules, in particular romfs, but is not exported, so we get
ERROR: "mtd_mmap_capabilities" [fs/romfs/romfs.ko] undefined!
This adds the missing export.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b4caecd480 ("fs: introduce f_op->mmap_capabilities for nommu mmap support")
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Fastmap can miss a PEB if it is in the protection queue
and not jet in the used tree.
Treat every protected PEB as used.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
UBI uses positive function return codes internally, and should not propagate
them up, except in the place this path fixes. Here is the original bug report
from Dan Carpenter:
The problem is really in ubi_eba_read_leb().
drivers/mtd/ubi/eba.c
412 err = ubi_io_read_vid_hdr(ubi, pnum, vid_hdr, 1);
413 if (err && err != UBI_IO_BITFLIPS) {
414 if (err > 0) {
415 /*
416 * The header is either absent or corrupted.
417 * The former case means there is a bug -
418 * switch to read-only mode just in case.
419 * The latter case means a real corruption - we
420 * may try to recover data. FIXME: but this is
421 * not implemented.
422 */
423 if (err == UBI_IO_BAD_HDR_EBADMSG ||
424 err == UBI_IO_BAD_HDR) {
425 ubi_warn("corrupted VID header at PEB %d, LEB %d:%d",
426 pnum, vol_id, lnum);
427 err = -EBADMSG;
428 } else
429 ubi_ro_mode(ubi);
On this path we return UBI_IO_FF and UBI_IO_FF_BITFLIPS and it
eventually gets passed to ERR_PTR(). We probably dereference the bad
pointer and oops. At that point we've gone read only so it was already
a bad situation...
430 }
431 goto out_free;
432 } else if (err == UBI_IO_BITFLIPS)
433 scrub = 1;
434
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Let's prefix UBI messages with 'ubiX' instead of 'UBI-X' - this is more
consistent with the way we name UBI devices.
Also, commit "32608703 UBI: Extend UBI layer debug/messaging capabilities"
added the function name print to 'ubi_msg()' - lets revert this change, since
these messages are supposed to be just informative messages, and not debugging
messages.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Some cosmetic fixes to the patch "UBI: Extend UBI layer debug/messaging
capabilities".
Signed-off-by: Tanya Brokhman <tlinder@codeaurora.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Adds a new set of functions to deal with scatter gather.
ubi_eba_read_leb_sg() will read from a LEB into a scatter gather list.
The new data structure struct ubi_sgl will be used within UBI to
hold the scatter gather list itself and metadata to have a cursor
within the list.
Signed-off-by: Richard Weinberger <richard@nod.at>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
By using UBI_METAONLY in rename_volumes() it is now possible to rename
an UBI volume atomically while it is open for writing.
This is useful for firmware upgrades.
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Andrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
Tested-by: Guido Martínez <guido@vanguardiasur.com.ar>
Reviewed-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Christoph Fritz <chf.fritz@googlemail.com>
Tested-by: Andrew Murray <amurray@embedded-bits.co.uk>
UBI_METAONLY is a new open mode for UBI volumes, it indicates
that only meta data is being changed.
Meta data in terms of UBI volumes means data which is stored in the
UBI volume table but not on the volume itself.
While it does not interfere with UBI_READONLY and UBI_READWRITE
it is not allowed to use UBI_METAONLY together with UBI_EXCLUSIVE.
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Andrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
Tested-by: Guido Martínez <guido@vanguardiasur.com.ar>
Reviewed-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Christoph Fritz <chf.fritz@googlemail.com>
Tested-by: Andrew Murray <amurray@embedded-bits.co.uk>
The MTD API reports -EUCLEAN only if the maximum number of bitflips
found in any ECC block exceeds a certain threshold. This is done to
avoid excessive -EUCLEAN reports to MTD users, which may induce
additional scrubbing of data, even when the ECC algorithm in use is
perfectly capable of handling the bitflips.
This threshold can be controlled by user-space (via sysfs), to allow
users to determine what they are willing to tolerate in their
application. But it still helps to have sane defaults.
In recent discussion [1], it was pointed out that our default threshold
is equal to the correction strength. That means that we won't actually
report any -EUCLEAN (i.e., "bitflips were corrected") errors until there
are almost too many to handle. It was determined that 3/4 of the
correction strength is probably a better default.
[1] http://lists.infradead.org/pipermail/linux-mtd/2015-January/057259.html
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
Since "BDI: Provide backing device capability information [try #3]" the
backing_dev_info structure also provides flags for the kind of mmap
operation available in a nommu environment, which is entirely unrelated
to it's original purpose.
Introduce a new nommu-only file operation to provide this information to
the nommu mmap code instead. Splitting this from the backing_dev_info
structure allows to remove lots of backing_dev_info instance that aren't
otherwise needed, and entirely gets rid of the concept of providing a
backing_dev_info for a character device. It also removes the need for
the mtd_inodefs filesystem.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Tejun Heo <tj@kernel.org>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since in SAMA5D4 chip, the PMECC can correct bit flips in erased page.
So we add a DT property to indicate this hardware character.
If the PMECC support correct bitflip erased page (all data are 0xff).
Then we can use the PMECC correct the page and skip the erased page
check.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
atmel_nand_pmecc_read_page() will return the total bitflips in this
page. This is incorrect.
As one nand page includes multiple ecc sectors, that will cause the
returned total bitflips exceed ecc capablity.
So this patch will make pmecc_correct() return the max bitflips of all
sectors in the page. That also makes atmel_nand_pmecc_read_page() return
the max bitflips.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When removing the fsl-quadspi module and running 'cat /proc/mtd' afterwards,
we see garbage data like:
$ rmmod fsl-quadspi
$ cat /proc/mtd
dev: size erasesize name
mtd0: 00000000 00000000 "(null)"
mtd0: 00000000 00000000 "(null)"
mtd0: 00000000 00000000 "(null)"
...
mtd0: a22296c6c756e28 00000000 "(null)"
mtd0: a22296c6c756e28 3064746d "(null)"
If we continue doing multiple module load/unload operations, then it will also
lead to a kernel crash.
The reason for this is due to the wrong mtd index used in
mtd_device_unregister() in the remove function.
We need to keep the mtd unregister index aligned with the one used in the probe
function, which means we need to take into account the 'has_second_chip'
property. By doing so we can guarantee that the mtd index is the same in the
registration and unregistration functions.
With this patch applied we can load/unload the fsl-quadspi driver several times
and it will result in no crash.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
Tested-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Allen Xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There is no path to switch to STATE_DATAOUT_STATUS_M state, and
OPT_SMARTMEDIA is unused.
This is leftover from commit 0be718e552
("mtd: nand: remove a bunch of unused commands").
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In initialization routine, mtd_info->owner is overwritten by memset()
just after being initialized. This can be fixed by moving memset() calls
to just before setting mtd_info->owner. But the memory region is allocated
by kmalloc, so we can fix it by using kzalloc instead of kmalloc.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
i.mx6 sx support turn off fastmix and megamix power.
qpsi controller can be turned off and all status lost when suspend/resume.
add suspend/resume functions and reset qspi controller when resume.
Signed-off-by: Allen Xu <b45815@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
commit 3157d1ed23 ("mtd: denali: remove unnecessary casts") introduced
an error by using a wrong bitmask.
A uint16_t cast was replaced with & 0xff, should be & 0xffff.
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
drivers/mtd/devices/st_spi_fsm.c:1647:17:
warning: comparison between signed and unsigned integer expressions
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
ST's Common Clk Framework is now available. This patch ensures the FSM
makes use of it by obtaining and enabling the EMI clock. If system fails
to provide the EMI clock, we bomb out.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Under certain conditions, the SPI-FSM Controller can be left in a state where
the data FIFO is not entirely empty. This can lead to problems where subsequent
data transfers appear to have been shifted by a number of unidentified bytes.
One simple example would be an errant FSM sequence which loaded more data to the
FIFO than was read by the host. Another more interesting case results from an
obscure artefact in the FSM Controller. When switching from data transfers in
x4 or x2 mode to data transfers in x1 mode, extraneous bytes will appear in the
FIFO, unless the previous data transfer was a multiple of 32 cycles (i.e. 8
bytes for x2, and 16 bytes for x4). This applies equally whether FSM is being
operated directly by a S/W driver, or by the SPI boot-controller in FSM-Boot
mode. Furthermore, data in the FIFO not only survive a transition between
FSM-Boot and FSM, but also a S/W reset of IP block [1].
By taking certain precautions, it is possible to prevent the driver from causing
this type of problem (e.g. ensuring that the host and programmed sequence
agree on the transfer size, and restricting transfer sizes to multiples of
32-cycles [2]). However, at the point the driver is loaded, no assumptions can be
made regarding the state of the FIFO. Even if previous S/W drivers have behaved
correctly, it is impossible to control the number of transactions serviced by
the controller operating in FSM-Boot.
To address this problem, we ensure the FIFO is cleared during initialisation,
before performing any FSM operations. Previously, the fsm_clear_fifo() code was
capable of detecting and clearing any unwanted 32-bit words from the FIFO. This
patch extends the capability to handle an arbitrary number of bytes present in
the FIFO [3]. Now that the issue is better understood, we also remove the calls
to fsm_clear_fifo() following the fsm_read() and fsm_write() operations.
The process of actually clearing the FIFO deserves a mention. While the FIFO
may contain any number of bytes, the SPI_FAST_SEQ_STA register only reports the
number of complete 32-bit words present. Furthermore, data can only be drained
from the FIFO by reading complete 32-bit words. With this in mind, a two stage
process is used to the clear the FIFO:
1. Read any complete 32-bit words from the FIFO, as reported by the
SPI_FAST_SEQ_STA register.
2. Mop up any remaining bytes. At this point, it is not known if there
are 0, 1, 2, or 3 bytes in the FIFO. To handle all cases, a dummy
FSM sequence is used to load one byte at a time, until a complete
32-bit word is formed; at most, 4 bytes will need to be loaded.
[1] Although this issue has existed since early versions of the SPI-FSM
controller, its full extent only emerged recently as a consequence of the
targetpacks starting to use FSM-Boot(x4) as the default configuration.
[2] The requirement to restrict transfers to multiples of 32 cycles was found
empirically back when DUAL and QUAD mode support was added. The current
analysis now gives a satisfactory explanation for this requirement.
[3] Theoretically, it is possible for the FIFO to contain an arbitrary number of
bits. However, since there are no known use-cases that leave incomplete
bytes in the FIFO, only words and bytes are considered here.
Signed-off-by: Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
UBI needs to know the physical erase block size, even on read-only
devices, since it defines the on-device layout. Use a device-tree
provided value to support previously written UBI on read-only NOR.
UBI also needs a non-zero writebufsize, so we set it to one.
Note: This was implemented because hardware write-protected CFI
NOR cannot be probed for the physical erase block size.
Signed-off-by: Joe Schultz <jschultz@xes-inc.ccom>
Signed-off-by: Aaron Sierra <asierra@xes-inc.ccom>
[Brian: removed unneeded #ifdef, note 'optional' erase-size property]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Previously, when probing a CFI chip which was write-protected at the
hardware level, the probe would fail due to the fact it could not put
the chip into QUERY mode. This would result in no MTD devices being
created.
Add a fallback to probe using the map_rom driver if the user-selected
probe fails.
Signed-off-by: Joe Schultz <jschultz@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We need to compare ret variable for negative value. The current code
assigns the boolean to the ret and prints it wrongly in the warning
message.
Reported-by: Andrey Karpov <karpov@viva64.com>
Cc: Giel van Schijndel <me@mortis.eu>
Cc: Dimitri Gorokhovik <dimitri.gorokhovik@free.fr>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Commit 7854d3f749 ("mtd: spelling, capitalization, uniformity") added
a correctly spelled line, but failed to remove the wrongly spelled one.
Commit 064a7694b5 ("mtd: Fix typo mtd/tests") then fixed the spelling
again, but left the duplication.
Fixes: 7854d3f749 ("mtd: spelling, capitalization, uniformity")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add nand_shutdown to wait for current nand operations to finish and prevent
further operations by changing the nand flash state to FL_SHUTDOWN.
This is addressing a problem observed during reboot tests using UBIFS
root file system: NAND erase operations that are in progress during
system reboot/shutdown are causing partial erased blocks. Although UBI should
be able to detect and recover from this error, this change will avoid
the creation of partial erased blocks on reboot in the middle of a NAND erase
operation.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
cfi_cmdset_000{1,2}.c already implement their own reboot notifiers, and
we're going to add one for NAND. Let's put the boilerplate in one place.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Scott Branden <sbranden@broadcom.com>
The global lock mtdblks_lock was used to protect the original mtdblks
array to avoid race conditions. As the mtdblks array was already gone,
but the mtdblks_lock is left, and it causes latency when open/release dev.
So we need to remove it here.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
SquashFS is supposed to use magic defined as SQUASHFS_MAGIC. What we
were supporting so far (SQSH_MAGIC) is something ZTE specific.
This patch adds support for Xiaomi R1D.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some devices like Netgear WNR1000v3 or WGR614v10 have partitions aligned
to 0x1000. Using bigger blocksize stopped us from detecting some parts.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds code which enables Quad I/O mode on Micron SPI NOR flashes.
For Micron SPI NOR flash, enabling or disabling quad I/O protocol can be
done By two methods, which are to use EVCR (Enhanced Volatile
Configuration Register) and the ENTER QUAD I/O MODE command. There is no
difference between these two methods. Unfortunately, for some Micron SPI
NOR flashes, there no ENTER Quad I/O command (35h), such as n25q064. But
for all current Micron SPI NOR, if it support quad I/O mode, using EVCR
definitely be supported. It is a recommended method to enable Quad I/O
mode by EVCR, Quad I/O protocol bit 7. When EVCR bit 7 is reset to 0,
the SPI NOR flash will operate in quad I/O mode.
This patch has been tested on N25Q512A and MT25TL256BAA1ESF. Micron SPI
NOR of spi_nor_ids[] table all support this method.
Signed-off-by: Bean Huo <beanhuo@micron.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Now that we have raw functions properly implemented we can remove this
FIXME.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
mx28evk board has a socket for NAND flash that comes with no NAND flash
populated, and then we get this message on every boot:
[ 1.657603] gpmi-nand 8000c000.gpmi-nand: driver registration failed: -19
which is not very helpful, so get rid of this error message.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
* Add device tree support for DoC3
* SPI NOR:
Refactoring, for better layering between spi-nor.c and its driver users
(e.g., m25p80.c)
New flash device support
Support 6-byte ID strings
* NAND
New NAND driver for Allwinner SoC's (sunxi)
GPMI NAND: add support for raw (no ECC) access, for testing purposes
Add ATO manufacturer ID
A few odd driver fixes
* MTD tests:
Allow testers to compensate for OOB bitflips in oobtest
Fix a torturetest regression
* nandsim: Support longer ID byte strings
And more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gDW8
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20141215' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"Summary:
- Add device tree support for DoC3
- SPI NOR:
Refactoring, for better layering between spi-nor.c and its
driver users (e.g., m25p80.c)
New flash device support
Support 6-byte ID strings
- NAND:
New NAND driver for Allwinner SoC's (sunxi)
GPMI NAND: add support for raw (no ECC) access, for testing
purposes
Add ATO manufacturer ID
A few odd driver fixes
- MTD tests:
Allow testers to compensate for OOB bitflips in oobtest
Fix a torturetest regression
- nandsim: Support longer ID byte strings
And more"
* tag 'for-linus-20141215' of git://git.infradead.org/linux-mtd: (63 commits)
mtd: tests: abort torturetest on erase errors
mtd: physmap_of: fix potential NULL dereference
mtd: spi-nor: allow NULL as chip name and try to auto detect it
mtd: nand: gpmi: add raw oob access functions
mtd: nand: gpmi: add proper raw access support
mtd: nand: gpmi: add gpmi_copy_bits function
mtd: spi-nor: factor out write_enable() for erase commands
mtd: spi-nor: add support for s25fl128s
mtd: spi-nor: remove the jedec_id/ext_id
mtd: spi-nor: add id/id_len for flash_info{}
mtd: nand: correct the comment of function nand_block_isreserved()
jffs2: Drop bogus if in comment
mtd: atmel_nand: replace memcpy32_toio/memcpy32_fromio with memcpy
mtd: cafe_nand: drop duplicate .write_page implementation
mtd: m25p80: Add support for serial flash Spansion S25FL132K
MTD: m25p80: fix inconsistency in m25p_ids compared to spi_nor_ids
mtd: spi-nor: improve wait-till-ready timeout loop
mtd: delete unnecessary checks before two function calls
mtd: nand: omap: Fix NAND enumeration on 3430 LDP
mtd: nand: add ATO manufacturer info
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
The torture test should quit once it actually induces an error in the
flash. This step was accidentally removed during refactoring.
Without this fix, the torturetest just continues infinitely, or until
the maximum cycle count is reached. e.g.:
...
[ 7619.218171] mtd_test: error -5 while erasing EB 100
[ 7619.297981] mtd_test: error -5 while erasing EB 100
[ 7619.377953] mtd_test: error -5 while erasing EB 100
[ 7619.457998] mtd_test: error -5 while erasing EB 100
[ 7619.537990] mtd_test: error -5 while erasing EB 100
...
Fixes: 6cf78358c9 ("mtd: mtd_torturetest: use mtd_test helpers")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <stable@vger.kernel.org>
On device remove, when testing the cmtd field of an of_flash
struct to decide whether it is a concatenated device or not,
we get a false positive on cmtd == NULL, and dereference it
subsequently. This may occur if of_flash_remove() is called
from the cleanup path of of_flash_probe().
Instead, test for NULL first, and only then perform the test
for a concatenated device.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This will allow spi-nor users to plainly use JEDEC to detect flash chip.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Implement raw OOB access functions to retrieve OOB bytes when accessing the
NAND in raw mode.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Several MTD users (either in user or kernel space) expect a valid raw
access support to NAND chip devices.
This is particularly true for testing tools which are often touching the
data stored in a NAND chip in raw mode to artificially generate errors.
The GPMI drivers do not implemenent raw access functions, and thus rely on
default HW_ECC scheme implementation.
The default implementation consider the data and OOB area as properly
separated in their respective NAND section, which is not true for the GPMI
controller.
In this driver/controller some OOB data are stored at the beginning of the
NAND data area (these data are called metadata in the driver), then ECC
bytes are interleaved with data chunk (which is similar to the
HW_ECC_SYNDROME scheme), and eventually the remaining bytes are used as
OOB data.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add a new function to copy bits (not bytes) from a memory region to
another one.
This function is similar to memcpy except it acts at bit level.
It is needed to implement GPMI raw access functions and adapt to the
hardware ECC engine which does not pad ECC bits to the next byte boundary.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
write_enable() was being duplicated to both m25p80.c and fsl-quadspi.c.
But this should be handled within the spi-nor abstraction layer.
At the same time, let's add write_disable() after erasing, so we don't
leave the flash in a write-enabled state afterward.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
We need to store the six bytes ID for s25fl128s, since it shares the same
five bytes with s25fl129p1.
This patch adds a macro INFO6 which is used for the six bytes ID flash, and adds
a new item for the s25fl128s.
Signed-off-by: Huang Shijie <shijie.huang@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The "id" array contains all the information about the JEDEC and the
manufacturer ID info. This patch removes the jedec_id/ext_id from
flash_info.
Signed-off-by: Huang Shijie <shijie.huang@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds the id/id_len fields for flash_info{}, and rewrite the
INFO to fill them. And at last, we read out 6 bytes in the spi_nor_read_id(),
and we use these new fields to parse out the correct flash_info.
Signed-off-by: Huang Shijie <shijie.huang@intel.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There is no need to use memcpy32_toio/memcpy32_fromio to transfer data
between memory and NFC sram. As the NFC sram is a also a memory space
not an I/O space, we can just use memcpy().
We remove the __iomem prefix for NFC sram to avoid sparse warnings.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This write_page() function is functionally equivalent to the default in
nand_base.c. Its only difference is in subpage programming support,
which cafe_nand.c does not advertise, so the difference is negligible.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
As stated in a5b7616c5, "mtd: m25p80,spi-nor: Fix module aliases for
m25p80", m25p_ids[] in m25p80.c needs to be kept in sync with
spi_nor_ids[] in spi-nor.c. The change here corrects a misalignment.
(We were missing m25px80 and we had a duplicate w25q128.)
Signed-off-by: Alison Chaiken <alison_chaiken@mentor.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: <stable@vger.kernel.org> # 3.18+
There are a few small issues with the timeout loop in
spi_nor_wait_till_ready():
* The first operation should not be a reschedule; we should check the
status register at least once to see if we're complete!
* We should check the status register one last time after declaring the
deadline has passed, to prevent a premature timeout error (this is
theoretically possible if we sleep for a long time after the previous
status register check).
* Add an error message, so it's obvious if we ever hit a timeout.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
The functions kfree() and pci_dev_put() test whether their argument is NULL
and then return immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
3430LDP has NAND flash with 32 bytes OOB size which is sufficient to hold
BCH8 codes but the small page check introduced in
commit b491da7233 ("mtd: nand: omap: clean-up ecc layout for BCH ecc schemes")
considers anything below 64 bytes unsuitable for BCH4/8/16. There is another
bug in that code where it doesn't skip the check for OMAP_ECC_HAM1_CODE_SW.
Get rid of that small page check code as it is insufficient and redundant
because we are checking for OOB available bytes vs ecc layout before calling
nand_scan_tail().
Fixes: b491da7233 ("mtd: nand: omap: clean-up ecc layout for BCH ecc schemes")
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It may be useful info, e.g. if someone wants to use ubinize.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fixes warning:
drivers/mtd/tests/oobtest.c: In function 'memcmpshow':
drivers/mtd/tests/oobtest.c:129: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'size_t'
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
It is common for NAND devices to have bitflip errors.
Add a bitflip_limit parameter to specify how many bitflips per
page we can tolerate without flagging an error.
By default zero bitflips are tolerated.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add a function memcmpshow() that compares the 2 data buffers
and shows the address:offset and data bytes on comparison failure.
This function does not break at a comparison failure but runs the
check for the whole data buffer.
Use memcmpshow() instead of memcmp() for all the verification paths.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The logic of vfree()'ing vol->upd_buf is tied to vol->updating.
In ubi_start_update() vol->updating is set long before vmalloc()'ing
vol->upd_buf. If we encounter a write failure in ubi_start_update()
before vmalloc() the UBI device release function will try to vfree()
vol->upd_buf because vol->updating is set.
Fix this by allocating vol->upd_buf directly after setting vol->updating.
Fixes:
[ 31.559338] UBI warning: vol_cdev_release: update of volume 2 not finished, volume is damaged
[ 31.559340] ------------[ cut here ]------------
[ 31.559343] WARNING: CPU: 1 PID: 2747 at mm/vmalloc.c:1446 __vunmap+0xe3/0x110()
[ 31.559344] Trying to vfree() nonexistent vm area (ffffc90001f2b000)
[ 31.559345] Modules linked in:
[ 31.565620] 0000000000000bba ffff88002a0cbdb0 ffffffff818f0497 ffff88003b9ba148
[ 31.566347] ffff88002a0cbde0 ffffffff8156f515 ffff88003b9ba148 0000000000000bba
[ 31.567073] 0000000000000000 0000000000000000 ffff88002a0cbe88 ffffffff8156c10a
[ 31.567793] Call Trace:
[ 31.568034] [<ffffffff818f0497>] dump_stack+0x4e/0x7a
[ 31.568510] [<ffffffff8156f515>] ubi_io_write_vid_hdr+0x155/0x160
[ 31.569084] [<ffffffff8156c10a>] ubi_eba_write_leb+0x23a/0x870
[ 31.569628] [<ffffffff81569b36>] vol_cdev_write+0x226/0x380
[ 31.570155] [<ffffffff81179265>] vfs_write+0xb5/0x1f0
[ 31.570627] [<ffffffff81179f8a>] SyS_pwrite64+0x6a/0xa0
[ 31.571123] [<ffffffff818fde12>] system_call_fastpath+0x16/0x1b
Cc: <stable@vger.kernel.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
If the erase worker is unable to erase a PEB it will
free the ubi_wl_entry itself.
The failing ubi_wl_entry must not free()'d again after
do_sync_erase() returns.
Cc: <stable@vger.kernel.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This is more a cosmetic change than a fix.
By using ubi_eba_atomic_leb_change()
we can guarantee that the first VTBL record is always
correct and we don't really need the second one anymore.
But we have to keep the second one to not break anything.
Artem: add a comment
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
If there is more then one UBI device mounted, there is no way to
distinguish between messages from different UBI devices.
Add device number to all ubi layer message types.
The R/O block driver messages were replaced by pr_* since
ubi_device structure is not used by it.
Amended a bit by Artem.
Signed-off-by: Tanya Brokhman <tlinder@codeaurora.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Freescale's QorIQ T Series processors support 8 IFC chip selects
within a memory map backward compatible with previous P Series
processors which supported only 4 chip selects.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If there is no PMECC lookup table stored in ROM, or lookup table offset is
not specified, PMECC driver should build it in DDR by itself.
That make the PMECC driver work for some board which doesn't have PMECC
lookup table in ROM.
The PMECC use the BCH algorithm, so based on the build_gf_tables()
function in lib/bch.c, we can build the Galois Field lookup table.
For more information can refer to section 5.4 of PMECC controller
application note:
http://www.atmel.com/images/doc11127.pdf
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The driver was also using own method to do 32bit copy, turns out
we have a kernel API so use that instead
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The ->PUtable[] array has "->nb_blocks" number of elemetns so this
comparison should be ">=" instead of ">". Otherwise it could result in
a minor read beyond the end of an array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add sst25wf080 to the spi-nor device id table.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested with this particular FRAM chip
Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The AM335x Technical Reference Manual (spruh73j.pdf) says
"Because the ECC engine includes only one accumulation context,
it can be allocated to only one chip-select at a time ... "
(7.1.3.3.12.3). Since the commit 97a288ba2c ("ARM: omap2+:
gpmc-nand: Use dynamic platform_device_alloc()") gpmc-nand
driver supports multiple NAND flash devices connected to
the single controller.
Use global 'struct nand_hw_control' among multiple NAND
instances to synchronize the access to the single ECC Engine.
Tested with custom AM335x board using 2x NAND flash chips.
Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Because n25q032 is the Micron SPI chip, move it to Micron
devices list group. In order that know which Micron SPI
chips have been support at a glance.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Huang Shijie <shijie8@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We are trying to remove the legacy tx_dma and rx_dma fields from the
spi_transfer structure. Currently dataflash uses tx_dma but only to make
sure that it's set to 0 so we can remove this use by replacing with a
zero initialisation of the entire spi_transfer struct.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We don't need to expose a 'wait-till-ready' interface to drivers. Status
register polling should be handled by the core spi-nor.c library, and as
of now, I see no need to provide a special driver-specific hook for it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
spi-nor.c should be taking care of these now.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Huang Shijie <b32955@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
We shouldn't have *every* function checking if a previous write is
complete; this should be done synchronously after each write/erase.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The error label was unused here. It looks like we're missing at least
one case that should be doing 'goto write_err'.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Huang Shijie <shijie8@gmail.com>
These functions were near-carbon-copies due to a small per-flash quirk.
Let's add a new spi_nor::flags bitfield to support these types of
quirks.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Graham Moore <grmoore@altera.com>
Cc: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The help text of CONFIG_MTD_OF_PARTS refers to additional documentation
in booting-without-of.txt but this documentation was moved to another
file in commit efcc2da3fd (Stefan Roese:
Factor MTD physmap bindings out of booting-without-of). This updates the
help text to point to the right place.
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
[Brian: fixed doc reference]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
update a comment in nand_command_lp() about specific requirements of
individual commands, the DEPLETE1 command was removed in the past and
the comment no longer applied
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
For the DDR Quad read, the dummy cycles maybe 3 or 6 which is less then 8.
The dummy cycles is actually 8 for SPI fast/dual/quad read.
This patch makes preparations for the DDR quad read, it fixes the wrong dummy
value for both the spi-nor.c and m25p80.c.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
NAND devices with page sizes over 4 KiB require more than 4-bits of ECC
coverage. This patch calculates the value of ecc_bytes based on a still
assumed 512-byte step size (13-bits) and the ecc_strength.
Example:
Micron M73A devices (8 KiB page) require 8-bit ECC per 512-byte
Signed-off-by: Jordan Friendshuh <jfriendshuh@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The drivers/mtd/nand/gpio.c driver does not GPIO bitbang the complete
NAND protocol, but instead is GPIO _assisted_ -- a memory mapped interface
communicates commands and data, and only few control signals are connected
to GPIO pins.
Expand comments in the driver source and in the Kconfig description to
better reflect the very nature of the driver. The previous text could be
mistaken for complete GPIO bitbanging.
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
* A regression from 3.16 which was noticed in 3.17. With the restructuring of
the m25p80.c driver and the SPI NOR library framework, we omitted proper
listing of the SPI device IDs. This means m25p80.c wouldn't auto-load
(modprobe) properly when built as a module. For now, we duplicate the device
IDs into both modules.
* The OMAP / ELM modules were depending on an implicit link ordering. Use
deferred probing so that the new link order (in 3.18-rc) can still allow for
successful probing.
* Fix suspend/resume support for LH28F640BF NOR flash
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=IxjM
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20141102' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"Three main MTD fixes for 3.18:
- A regression from 3.16 which was noticed in 3.17. With the
restructuring of the m25p80.c driver and the SPI NOR library
framework, we omitted proper listing of the SPI device IDs. This
means m25p80.c wouldn't auto-load (modprobe) properly when built as
a module. For now, we duplicate the device IDs into both modules.
- The OMAP / ELM modules were depending on an implicit link ordering.
Use deferred probing so that the new link order (in 3.18-rc) can
still allow for successful probing.
- Fix suspend/resume support for LH28F640BF NOR flash"
* tag 'for-linus-20141102' of git://git.infradead.org/linux-mtd:
mtd: cfi_cmdset_0001.c: fix resume for LH28F640BF chips
mtd: omap: fix mtd devices not showing up
mtd: m25p80,spi-nor: Fix module aliases for m25p80
mtd: spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id
mtd: m25p80: get rid of spi_get_device_id
After '#echo mem > /sys/power/state' some devices can not be properly resumed
because apparently the MTD Partition Configuration Register has been reset
to default thus the rootfs cannot be mounted cleanly on resume.
An example of this can be found in the SA-1100 Developer's Manual at 9.5.3.3
where the second step of the Sleep Shutdown Sequence is described:
"An internal reset is applied to the SA-1100. All units are reset...".
As workaround we refresh the PCR value as done initially on chip setup.
This behavior and the fix are confirmed by our tests done on 2 different Zaurus
collie units with kernel 3.17.
Fixes: 812c5fa82bae: ("mtd: cfi_cmdset_0001.c: add support for Sharp LH28F640BF NOR")
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Since commit 6d178ef2fd ("mtd: nand: Move ELM driver and rename as
omap_elm"), I don't have any mtd devices present on my am335x. This
changes the link order of the omap_elm and omap2 objects, causing them
to probe in the wrong order.
To fix this, make elm_config defer probing until the omap_elm driver is
actually loaded.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add support for the sunxi NAND Flash Controller (NFC).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Brian: tweaked to fix ecc->steps issue]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
nandsim can simulate NAND Flash which returns the ID bytes specified
by first_id_byte, ..., fourth_id_byte module parameters.
In order to simulate NAND flash which returns more than four ID bytes,
this adds id_bytes module parameter which is specified by the array of
byte like this:
# modprobe nandsim id_bytes=0x98,0xdc,0x90,0x26,0x76,0x15,0x01,0x08 bch=1
This doesn't add fifth_id_byte, ..., seventh_id_byte module parameters,
because they are redundant. But the existing first_id_byte, ...,
fourth_id_byte module parameters are preserved and add "(obsolete)" to
the description.
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
With CONFIG_OF=n, we can see the following warning:
drivers/mtd/devices/docg3.c:2122:28: warning: 'docg3_dt_ids' defined but not used [-Wunused-variable]
static struct of_device_id docg3_dt_ids[] = {
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Sometimes the trx offsets are 0, in that case there is no partition and
we should not try to add one.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[Brian: rewrapped]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Modify phram to include <linux/io.h> rather than <asm/io.h>
Signed-off-by: Rob Ward <robert.ward114@googlemail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When clk_prepare_enable(q->clk) fails it is clearer to disable the previous
acquired clock (q->clk_en) in the error path rather than doing it locally.
So disable q->clk_en in the error path only.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The 'map_failed' label will return 'ret', so we need to assign the error
code to 'ret', otherwise the probe function will return success.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This replaces kzalloc() and ioremap() calls by devm_ functions
in the probe() routine, which automatically release the corresponding
resources when probe() fails or when the device is removed.
This simplifies simplifies the error management code, and brings
the below improvements or changes:
A. Fixing a bug reported by "make coccicheck":
If "board = devm_kzalloc()" fails, the probe() function jumps
incorrectly to label "no_res" and therefore returns without
running iounmap().
B. Requesting the memory region
Using devm_ioremap_resource() makes the probe() function request
the corresponding memory region before running ioremap(), as
it is supposed to do.
C. Standardizing the error codes:
The use of devm_ioremap_resource() changes the return value:
* -ENOMEM instead of -EIO in case of ioremap() failure,
* -EINVAL instead of -ENODEV in case of platform_get_resource()
failure.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This is needed for some new Netgear devices (e.g. R6250).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Avoid the following compile warning:
drivers/mtd/maps/bfin-async-flash.c: In function 'bfin_flash_probe':
drivers/mtd/maps/bfin-async-flash.c:129: warning: unused variable 'ret'
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add device-tree support. This is straightforward as docg3 only uses the
standard IOMEM resources.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: devicetree@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Since the commit 97a288ba2c ("ARM: omap2+: gpmc-nand: Use
dynamic platform_device_alloc()") gpmc-nand driver supports
multiple NAND flash devices connected to the single controller.
Remove global variable to make the code thread-safe.
Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There is currently no useful way to override the default
implementation of this operation. The returned struct spi_device_id
must have a pointer to struct flash_info in its private data, but this
structure is defined inside spi-nor.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
seq_printf doesn't return a useful value, so remove
these misuses.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
m25p80's device ID table is now spi_nor_ids, defined in spi-nor. The
MODULE_DEVICE_TABLE() macro doesn't work with extern definitions, but
its use was also removed at the same time. Now if m25p80 is built as
a module it doesn't get the necessary aliases to be loaded
automatically.
A clean solution to this will involve defining the list of device
IDs in spi-nor.h and removing struct spi_device_id from the spi-nor
API, but this is quite a large change.
As a quick fix suitable for stable, copy the device IDs back into
m25p80.
Fixes: 03e296f613 ("mtd: m25p80: use the SPI nor framework")
Cc: <stable@vger.kernel.org> # 3.16.x: 32f1b7c8352f: mtd: move support for struct flash_platform_data into m25p80
Cc: <stable@vger.kernel.org> # 3.16.x: 90e55b3812a1: mtd: m25p80: get rid of spi_get_device_id
Cc: <stable@vger.kernel.org> # 3.16.x: 70f3ce0510af: mtd: spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id
Cc: <stable@vger.kernel.org> # 3.16.x
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
Pull block layer driver update from Jens Axboe:
"This is the block driver pull request for 3.18. Not a lot in there
this round, and nothing earth shattering.
- A round of drbd fixes from the linbit team, and an improvement in
asender performance.
- Removal of deprecated (and unused) IRQF_DISABLED flag in rsxx and
hd from Michael Opdenacker.
- Disable entropy collection from flash devices by default, from Mike
Snitzer.
- A small collection of xen blkfront/back fixes from Roger Pau Monné
and Vitaly Kuznetsov"
* 'for-3.18/drivers' of git://git.kernel.dk/linux-block:
block: disable entropy contributions for nonrot devices
xen, blkfront: factor out flush-related checks from do_blkif_request()
xen-blkback: fix leak on grant map error path
xen/blkback: unmap all persistent grants when frontend gets disconnected
rsxx: Remove deprecated IRQF_DISABLED
block: hd: remove deprecated IRQF_DISABLED
drbd: use RB_DECLARE_CALLBACKS() to define augment callbacks
drbd: compute the end before rb_insert_augmented()
drbd: Add missing newline in resync progress display in /proc/drbd
drbd: reduce lock contention in drbd_worker
drbd: Improve asender performance
drbd: Get rid of the WORK_PENDING macro
drbd: Get rid of the __no_warn and __cond_lock macros
drbd: Avoid inconsistent locking warning
drbd: Remove superfluous newline from "resync_extents" debugfs entry.
drbd: Use consistent names for all the bi_end_io callbacks
drbd: Use better variable names
NAND
* Cleanup for Denali driver
* Atmel: add support for new page sizes
* Atmel: fix up 'raw' mode support
* Atmel: miscellaneous cleanups
* New timing mode helpers for non-ONFI NAND
* OMAP: allow driver to be (properly) built as a module
* bcm47xx: RESET support and other cleanups
SPI NOR
* Miscellaneous cleanups, to prepare framework for wider use (some further
work still pending)
* Compile-time configuration to select 4K vs. 64K support for flash that
support both (necessary for using UBIFS on some SPI NOR)
A few scattered code quality fixes, detected by Coverity
See the changesets for more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/jCH
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20141015' of git://git.infradead.org/linux-mtd
Pull MTD update from Brian Norris:
"Sorry for delaying this a bit later than usual. There's one mild
regression from 3.16 that was noticed during the 3.17 cycle, and I
meant to send a fix for it along with this pull request. I'll
probably try to queue it up for a later pull request once I've had a
better look at it, hopefully by -rc2 at the latest.
Summary for this pull:
NAND
- Cleanup for Denali driver
- Atmel: add support for new page sizes
- Atmel: fix up 'raw' mode support
- Atmel: miscellaneous cleanups
- New timing mode helpers for non-ONFI NAND
- OMAP: allow driver to be (properly) built as a module
- bcm47xx: RESET support and other cleanups
SPI NOR
- Miscellaneous cleanups, to prepare framework for wider use (some
further work still pending)
- Compile-time configuration to select 4K vs. 64K support for flash
that support both (necessary for using UBIFS on some SPI NOR)
A few scattered code quality fixes, detected by Coverity
See the changesets for more"
* tag 'for-linus-20141015' of git://git.infradead.org/linux-mtd: (59 commits)
mtd: nand: omap: Correct CONFIG_MTD_NAND_OMAP_BCH help message
mtd: nand: Force omap_elm to be built as a module if omap2_nand is a module
mtd: move support for struct flash_platform_data into m25p80
mtd: spi-nor: add Kconfig option to disable 4K sectors
mtd: nand: Move ELM driver and rename as omap_elm
nand: omap2: Replace pr_err with dev_err
nand: omap2: Remove horrible ifdefs to fix module probe
mtd: nand: add Hynix's H27UCG8T2ATR-BC to nand_ids table
mtd: nand: support ONFI timing mode retrieval for non-ONFI NANDs
mtd: physmap_of: Add non-obsolete map_rom probe
mtd: physmap_of: Fix ROM support via OF
MAINTAINERS: add l2-mtd.git, 'next' tree for MTD
mtd: denali: fix indents and other trivial things
mtd: denali: remove unnecessary parentheses
mtd: denali: remove another set-but-unused variable
mtd: denali: fix include guard and license block of denali.h
mtd: nand: don't break long print messages
mtd: bcm47xxnflash: replace some magic numbers
mtd: bcm47xxnflash: NAND_CMD_RESET support
mtd: bcm47xxnflash: add cmd_ctrl handler
...
Drivers currently call spi_nor_match_id() and then spi_nor_scan().
This adds a dependency on struct spi_device_id which we want to
avoid. Make spi_nor_scan() do it for them.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This simplifies the way we use spi_nor framework and will allow us to
drop spi_nor_match_id.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The drivers should use dmaengine_terminate_all() API instead of
accessing the device_control which will be deprecated soon
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The drivers should use dmaengine_terminate_all() API instead of
accessing the device_control which will be deprecated soon
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The MTD_NAND_OMAP_BCH doesn't harm on legacy OMAP platforms
so don't state that it should be disabled for them.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit adds a hidden option to build the omap_elm as a module, if
omap2_nand is a module (and similarly in the built-in case).
This fixes the following build error when omap2_nand is chosen built-in,
and omap_elm is chosen as a module:
drivers/built-in.o: In function `omap_nand_probe':
drivers/mtd/nand/omap2.c:2010: undefined reference to `elm_config'
drivers/mtd/nand/omap2.c:1980: undefined reference to `elm_config'
drivers/mtd/nand/omap2.c:1927: undefined reference to `elm_config'
drivers/built-in.o: In function `omap_elm_correct_data':
drivers/mtd/nand/omap2.c:1444: undefined reference to `elm_decode_bch_error_page'
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Clear QUEUE_FLAG_ADD_RANDOM in all block drivers that set
QUEUE_FLAG_NONROT.
Historically, all block devices have automatically made entropy
contributions. But as previously stated in commit e2e1a148 ("block: add
sysfs knob for turning off disk entropy contributions"):
- On SSD disks, the completion times aren't as random as they
are for rotational drives. So it's questionable whether they
should contribute to the random pool in the first place.
- Calling add_disk_randomness() has a lot of overhead.
There are more reliable sources for randomness than non-rotational block
devices. From a security perspective it is better to err on the side of
caution than to allow entropy contributions from unreliable "random"
sources.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We need to add fm_sb too.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Tanya Brokhman <tlinder@codeaurora.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This "type" seems to be an extra hint for m25p80 about the flash. Some
archs register flash_platform_data with "name" set to "m25p80" and then
with a real flash name set in "type". It seems to be a trick specific
to the m25p80 so let's move it out of spi-nor.
Btw switch to the spi_nor_match_id instead of iterating spi_nor_ids.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Current situation with 4K sectors is quite messy. First of all, some
MTD "users" don't work with such small size. An example may be UBIFS
which requires 15 KiB erase blocks as a minimum. In theory spi-nor
should provide multiple erase regions and MTD "users" should use the
one they need. Unforunately that is not implemented.
In the result our flashes database in spi-nor is hackish. For some
flashes we pretend they don't support 4K sectors just because some
distribution uses UBIFS on it. This ofc leads to conflicts, like
Samsung using w25q128 with 4K sectors vs. OpenWrt requiring it to
pretend it's 64 KiB blocks only.
My idea (plan?) for fixing this situation:
1) Use real hw info (this requires a way for disabling 4K for now)
2) Provide detailed info about erase regions
3) Make UBIFS work with devices that support 4K sectors
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It confused me more than once that the cancel flag of the
work function does not indicate the cancellation of a single work.
In fact it indicates the WL sub-system shutdown and therefore
worker functions have to free their wl_entries too.
That's why you cannot cancel a single work, you can only shutdown
all works.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
There is no need to set err, it will be overwritten in any case
later at:
if (scrub)
err = ubi_wl_scrub_peb(ubi, pnum);
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The while loop in produce_free_peb() assumes that each work will produce a
free PEB. This is not true.
If ubi->works_count is 1 and the only scheduled work is the
wear_leveling_worker() produce_free_peb() can loop forever in case
nobody schedules an erase work.
Fix this issue by checking in the while loop whether work is scheduled.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The ELM driver is only used by the OMAP NAND driver, so let's move it
to the nand/ directory. Additionally, let's rename it to a less confusing
name, so the module is built with a meaningful name, instead of the previous
'elm.ko'.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Usage of pr_err is frowned upon, so replace it with dev_err.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The current code abuses ifdefs to determine if the selected ECC scheme
is supported by the running kernel. As a result the code is hard to read,
and it also fails to load as a module.
This commit removes all the ifdefs and instead introduces a function
omap2_nand_ecc_check() to check if the ECC is supported by using
IS_ENABLED(CONFIG_xxx).
Since IS_ENABLED() is true when a config is =y or =m, this change fixes the
module so it can be loaded with no issues.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the full description of the Hynix H27UCG8T2ATR-BC NAND chip in the
nand_ids table so that we can later use the NAND ECC infos and ONFI timings
mode in controller drivers.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add an onfi_timing_mode_default field to nand_chip and nand_flash_dev in
order to support NAND timings definition for non-ONFI NAND.
NAND that support better timings mode than the default one have to define
a new entry in the nand_ids table.
The default timing mode should be deduced from timings description from
the datasheet and the ONFI specification
(www.onfi.org/~/media/ONFI/specs/onfi_3_1_spec.pdf, chapter 4.15
"Timing Parameters").
You should choose the closest mode that fit the timings requirements of
your NAND chip.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Previously, the only way to map a NOR device as a simple ROM was to
use the obsolete "direct-mapped" compatible binding (which further
requires device_type = "nor" and probe-type = "NOR" properties).
This patch adds an "mtd-rom" compatible binding to the "map_rom"
probe type.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The "ROM" and unknown probe types within the obsolete "direct-mapped"
probe function used the nonexistent "mtd_rom" probe instead of the
intended "map_rom".
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
- Fix indents
- Do not break a line unless it is longer than 80 columns
- Do not insert a whitespace before ';'
- Use whitespaces around operators
- Use braces for a "else" block where the "if" block uses ones.
Besides, eliminate all the warnings reported by checkpatch.pl:
- WARNING: quoted string split across lines
- WARNING: else is not generally useful after a break or return
- WARNING: Missing a blank line after declarations
- WARNING: Avoid line continuations in quoted strings
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We should use parentheses only when they are necessary
or they really improve the readability.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The variable "irq_status" in denali_read_page_raw() is set, but not used.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
I noticed this during a code review. We are checking that the strlen()
of ->name is not less than the ->name_len which the user gave us. I
believe this bug is harmless but clearly we meant to return here instead
of setting an error code and then not using it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
It looks like this header file is a concatenation of two headers.
Anyway, the include guard should be renamed and placed at the correct
postion and the license block in the middle should be deleted.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This follows Chapter 2 of Linux's CodingStyle:
> However, never break user-visible strings such as printk messages,
> because that breaks the ability to grep for them.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This won't be used by NAND subsystem as we implement cmdfunc on our
own, but will allow us to write a bit cleaner code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We are supposed to mask value, not multiply it. Add some comments btw.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Old devices used to have NVRAM at the very end of flash and they could
be unaligned (starting at some offset in a block).
In new devices NVRAM can be located quite randomly, however it seems to
always start at the beginning of a block. For example Netgear R6250 has
NVRAM located right after the bootloader, before the kernel partition.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
For PMECC, the pmecc_bytes_per_sector has same meaning as ecc.bytes.
So remove pmecc_bytes_per_sector and use ecc.bytes instead.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
For PMECC, the pmecc_sector_number has same meaning as ecc.steps.
So use ecc.steps to replace the pmecc_sector_number.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit adds a new platform-data boolean property that enables use
of a flash-based bad block table. This can also be enabled by setting
the 'nand-on-flash-bbt' devicetree property.
If the flash BBT is not enabled, the driver falls back to use OOB
bad block markers only, as before. If the flash BBT is enabled the
kernel will keep track of bad blocks using a BBT, in addition to
the OOB markers.
As explained by Brian Norris the reasons for using a BBT are:
""
The primary reason would be that NAND datasheets specify it these days.
A better argument is that nobody guarantees that you can write a
bad block marker to a worn out block; you may just get program failures.
This has been acknowledged by several developers over the last several
years.
Additionally, you get a boot-time performance improvement if you only
have to read a few pages, instead of a page or two from every block on
the flash.
""
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Retrieve the NFC clock to make sure it is enabled. Make that optional to ensure
compatibility with previous device trees but document it as mandatory so newer
device trees will include it.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The UBI_IOCVOLUP ioctl is used to start an update and also to
truncate a volume. In the first case, a "volume updated" notification
is dispatched when the update is done.
This commit adds the "volume updated" notification to be also sent when
the volume is truncated. This is required for UBI block and gluebi to get
notified about the new volume size.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@vger.kernel.org # v3.15+
Static volumes can change its 'used_bytes' when they get updated,
and so the block interface must listen to the UBI_VOLUME_UPDATED
notification to resize the block device accordingly.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@vger.kernel.org # v3.15+
We are currently taking the block device size from the ubi_volume_info.size
field. However, this is not the amount of data in the volume, but the
number of reserved physical eraseblocks, and hence leads to an incorrect
representation of the volume.
In particular, this produces I/O errors on static volumes as the block
interface may attempt to read unmapped PEBs:
$ cat /dev/ubiblock0_0 > /dev/null
UBI error: ubiblock_read_to_buf: ubiblock0_0 ubi_read error -22
end_request: I/O error, dev ubiblock0_0, sector 9536
Buffer I/O error on device ubiblock0_0, logical block 2384
[snip]
Fix this by using the ubi_volume_info.used_bytes field which is set to the
actual number of data bytes for both static and dynamic volumes.
While here, improve the error message to be less stupid and more useful:
UBI error: ubiblock_read_to_buf: ubiblock0_1 ubi_read error -9 on LEB=0, off=15872, len=512
It's worth noticing that the 512-byte sector representation of the volume
is only correct if the volume size is multiple of 512-bytes. This is true for
virtually any NAND device, given eraseblocks and pages are 512-byte multiple
and hence so is the LEB size.
Artem: tweak the error message and make it look more like other UBI error
messages.
Fixes: 9d54c8a33e ("UBI: R/O block driver on top of UBI volumes")
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@vger.kernel.org # v3.15+
commit 4df38926f3 ("UBI: block: Avoid disk size integer overflow")
introduced a dereference on dev (which is not initialized at that
point) when printing a warning message. Re-order disk_capacity check
after the dev is found.
Found by cppcheck:
[drivers/mtd/ubi/block.c:509]: (error) Uninitialized variable: dev
Artem: tweak the error message a bit
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
I ran into this error after a ubiupdatevol, because I forgot to backport
e9110361a9 UBI: fix the volumes tree sorting criteria.
UBI error: process_pool_aeb: orphaned volume in fastmap pool
UBI error: ubi_scan_fastmap: Attach by fastmap failed, doing a full scan!
kmem_cache_destroy ubi_ainf_peb_slab: Slab cache still has objects
CPU: 0 PID: 1 Comm: swapper Not tainted 3.14.18-00053-gf05cac8dbf85 #1
[<c000d298>] (unwind_backtrace) from [<c000baa8>] (show_stack+0x10/0x14)
[<c000baa8>] (show_stack) from [<c01b7a68>] (destroy_ai+0x230/0x244)
[<c01b7a68>] (destroy_ai) from [<c01b8fd4>] (ubi_attach+0x98/0x1ec)
[<c01b8fd4>] (ubi_attach) from [<c01ade90>] (ubi_attach_mtd_dev+0x2b8/0x868)
[<c01ade90>] (ubi_attach_mtd_dev) from [<c038b510>] (ubi_init+0x1dc/0x2ac)
[<c038b510>] (ubi_init) from [<c0008860>] (do_one_initcall+0x94/0x140)
[<c0008860>] (do_one_initcall) from [<c037aadc>] (kernel_init_freeable+0xe8/0x1b0)
[<c037aadc>] (kernel_init_freeable) from [<c02730ac>] (kernel_init+0x8/0xe4)
[<c02730ac>] (kernel_init) from [<c00093f0>] (ret_from_fork+0x14/0x24)
UBI: scanning is finished
Freeing the cache in the error path fixes the Slab error.
Tested on at91sam9g35 (3.14.18+fastmap backports)
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Cc: stable <stable@vger.kernel.org> # 3.10+
The variable "retry" in wait_for_irq() is set, but not used.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We should rathar use "int" type for loop iterators.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Useless casts result in unreadable source code.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
All of these variables are initialized to zero and then
set to a different value below.
Zero-initializing is redundant.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We should use
/*
* Blah Blah ...
* ...
*/
for multi-line comment blocks.
In addition, refactor some comments where it seems reasonable and
remove some comments where the code is clear enough such as:
/* clear interrupts */
clear_interrupts(denali);
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
* A tiny comment tweak, to kill a bunch of DocBook warnings added during the
merge window
* A small fixup to the OTP routines' error handling
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7uT9
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20140905' of git://git.infradead.org/linux-mtd
Pull mtd fixes from Brian Norris:
"Two trivial MTD updates for 3.17-rc4:
- a tiny comment tweak, to kill a bunch of DocBook warnings added
during the merge window
- a small fixup to the OTP routines' error handling"
* tag 'for-linus-20140905' of git://git.infradead.org/linux-mtd:
mtd: nand: fix DocBook warnings on nand_sdr_timings doc
mtd: cfi_cmdset_0002: check return code for get_chip()
commit 65b97cf6b8 introduced in v3.7 caused a regression
by using a reversed CS_MASK thus causing omap_calculate_ecc to
always fail. As the NAND base driver never checks for .calculate()'s
return value, the zeroed ECC values are used as is without showing
any error to the user. However, this won't work and the NAND device
won't be guarded by any error code.
Fix the issue by using the correct mask.
Code was tested on omap3beagle using the following procedure
- flash the primary bootloader (MLO) from the kernel to the first
NAND partition using nandwrite.
- boot the board from NAND. This utilizes OMAP ROM loader that
relies on 1-bit Hamming code ECC.
Fixes: 65b97cf6b8 (mtd: nand: omap2: handle nand on gpmc)
Cc: <stable@vger.kernel.org> [3.7+]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For v3.12 and prior, 1-bit Hamming code ECC via software was the
default choice. Commit c66d039197 in v3.13 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.
This ECC layout change causes NAND filesystems created in v3.12
and prior to be unusable in v3.13 and later. So revert back to
using software ECC by default if an ECC scheme is not explicitely
specified.
This defect can be observed on the following boards during legacy boot
-omap3beagle
-omap3touchbook
-overo
-am3517crane
-devkit8000
-ldp
-3430sdp
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It's a one-liner doing no magic and its name may be confusing because
it does not have to use JEDEC (e.g. when using alternative read_id).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix the bug in handling gpio flash read/write when offset + len
from MTD exceeds the window size
Signed-off-by: Aaron Wu <Aaron.wu@analog.com>
[Brian: made some commentary edits. Also note that the BUG_ON() was
provably false for all non-negative inputs (since x % y <= x), so we
dropped it.]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
drivers/mtd/nand/nand_timings.c:45: warning: integer constant is too large for ‘long’ type
[ Editorial note: This is a false warning. Looking at ISO draft N1124
(this is approximately C11, the first PDF I had lying around),
section 6.4.4.1 (statement 5):
"The type of an integer constant is the first of the
corresponding list in which its value can be represented."
So this should not be an overflow, and any toolchain that says so
(e.g., GCC 4.4) is buggy.
-Brian ]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When enable NFC sram write, it will failed the mtd_nandbiterrs.ko test.
As in driver's nfc_sram_write_page(), if ops->mode equal to MTD_OSP_RAW,
driver assumes the data buffer contains one page data and one oob data
followed. And driver will write the page data and oob data to nand.
But this is wrong implementation. Since the data buffer don't contains the
oob data to write. We should write the chip->oob_poi to nand's oob.
So this patch fix it by writing the oob data from chip->oob_poi.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
chip->pagebuf is a 32-bit type (int), so the shift will only be applied
as 32-bit. Fix this for 64-bit safety.
Caught by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The condition "if (irq_status == 0)" already ensures that one half of
the ternary ?: is dead. I think this should probably actually be a FAIL,
not a PASS.
Caught by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Jamie Iles <jamie@jamieiles.com>
These multiplications are done with 32-bit arithmetic, then converted to
64-bit. We should widen the integers first to prevent overflow. This
could be a problem for large (>4GB) MTD's.
Detected by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
MTD used to allow compiling out character device support. This was
dropped in the following commit, but some of the accompanying logic was
never dropped:
commit 660685d9d1
Author: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Date: Thu Mar 14 13:27:40 2013 +0200
mtd: merge mtdchar module with mtdcore
The weird logic was flagged by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
There is one theoretical case that could fall through to using an
uninitialized value as the return code. Let's give it a value of 0.
Untested.
Caught by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When checking the upper boundary (i.e., whether an address is higher
than the maximum size of the MTD), we should be doing an inclusive check
(greater or equal). For instance, an address of 16MB (0x1000000) on a
16MB device is invalid.
The strengthening of this bounds check is redundant for those which
already have a address+length check and ensure that the length is
non-zero, but let's just fix them all, for completeness.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The variable 'retries' is never modified, so if the reset operation
never is going to complete, we'll get stuck in an infinite loop.
It looks like the intention was to decrement 'retries' on every loop.
Untested.
Caught by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Do nand reset before write protect check.
If we want to check the WP# low or high through STATUS READ and check bit 7,
we must reset the device, other operation (eg.erase/program a locked block) can
also clear the bit 7 of status register.
As we know the status register can be refreshed, if we do some operation to trigger it,
for example if we do erase/program operation to one block that is locked, then READ STATUS,
the bit 7 of READ STATUS will be 0 indicate the device in write protect, then if we do
erase/program operation to another block that is unlocked, the bit 7 of READ STATUS will
be 1 indicate the device is not write protect.
Suppose we checked the bit 7 of READ STATUS is 0 then judge the WP# is low (write protect),
but in this case the WP# maybe high if we do erase/program operation to a locked block,
so we must reset the device if we want to check the WP# low or high through STATUS READ and
check bit 7.
Signed-off-by: White Ding <bpqw@micron.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fixed checkpatch warnings: "WARNING: Prefer seq_puts to seq_printf"
This patch is created with reference to the ongoing lkml thread
https://lkml.org/lkml/2014/7/15/646
where Andrew Morton wrote:
"
- puts is presumably faster
- puts doesn't go rogue if you accidentally pass it a "%".
- this patch would actually make compiled object files few bytes smaller.
Perhaps because seq_printf() is a varargs function, forcing the
caller to pass args on the stack instead of in registers.
"
Signed-off-by: Samarth Parikh <samarthp@ymail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
MAP10 command with '0x2000' data sets up a read-ahead/write access.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit adds the support in the spi-nor driver of the Micron
M25PX80 flash, a 8 Mbit SPI flash from Micron.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
PMECC can support 512, 1k, 2k, 4k, 8k page size.
The driver currently only support 2k page size nand flash. So this patch
add support to 512, 1k, 4k and 8k page size nand flash.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some nand with 8k page size like Micron MT29F32G08ABAAAWP need more than 20us.
Signed-off-by: Raphaël Poggi <poggi.raph@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use NULL instead of 0 when returning an address. This fixes a
sparse warning.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We check "cs" for array overflows but we don't check for underflows and
it upsets the static checkers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
fixes are:
* UBI deleted list items while iterating the list with 'list_for_each_entry'
* The UBI block driver did not work properly with very large UBI volumes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zgqa
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.17-rc1' of git://git.infradead.org/linux-ubifs
Pull UBI/UBIFS changes from Artem Bityutskiy:
"No significant changes, mostly small fixes here and there. The more
important fixes are:
- UBI deleted list items while iterating the list with
'list_for_each_entry'
- The UBI block driver did not work properly with very large UBI
volumes"
* tag 'upstream-3.17-rc1' of git://git.infradead.org/linux-ubifs: (21 commits)
UBIFS: Add log overlap assertions
Revert "UBIFS: add a log overlap assertion"
UBI: bugfix in ubi_wl_flush()
UBI: block: Avoid disk size integer overflow
UBI: block: Set disk_capacity out of the mutex
UBI: block: Make ubiblock_resize return something
UBIFS: add a log overlap assertion
UBIFS: remove unnecessary check
UBIFS: remove mst_mutex
UBIFS: kernel-doc warning fix
UBI: init_volumes: Ignore volumes with no LEBs
UBIFS: replace seq_printf by seq_puts
UBIFS: replace count*size kzalloc by kcalloc
UBIFS: kernel-doc warning fix
UBIFS: fix error path in create_default_filesystem()
UBIFS: fix spelling of "scanned"
UBIFS: fix some comments
UBIFS: remove useless @ecc in struct ubifs_scan_leb
UBIFS: remove useless statements
UBIFS: Add missing break statements in dbg_chk_pnode()
...
AMD-compatible CFI driver:
- Support OTP programming for Micron M29EW family
- Increase buffer write timeout, according to detected flash parameter info
NAND
- Add helpers for retrieving ONFI timing modes
- GPMI: provide option to disable bad block marker swapping (required for
Ka-On electronics platforms)
SPI NOR
- EON EN25QH128 support
- Support new Flag Status Register (FSR) on a few Micron flash
Common
- New sysfs entries for bad block and ECC stats
And a few miscellaneous refactorings, cleanups, and driver improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Wkmz
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20140808' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"AMD-compatible CFI driver:
- Support OTP programming for Micron M29EW family
- Increase buffer write timeout, according to detected flash
parameter info
NAND
- Add helpers for retrieving ONFI timing modes
- GPMI: provide option to disable bad block marker swapping (required
for Ka-On electronics platforms)
SPI NOR
- EON EN25QH128 support
- Support new Flag Status Register (FSR) on a few Micron flash
Common
- New sysfs entries for bad block and ECC stats
And a few miscellaneous refactorings, cleanups, and driver
improvements"
* tag 'for-linus-20140808' of git://git.infradead.org/linux-mtd: (31 commits)
mtd: gpmi: make blockmark swapping optional
mtd: gpmi: remove line breaks from error messages and improve wording
mtd: gpmi: remove useless (void *) type casts and spaces between type casts and variables
mtd: atmel_nand: NFC: support multiple interrupt handling
mtd: atmel_nand: implement the nfc_device_ready() by checking the R/B bit
mtd: atmel_nand: add NFC status error check
mtd: atmel_nand: make ecc parameters same as definition
mtd: nand: add ONFI timing mode to nand_timings converter
mtd: nand: define struct nand_timings
mtd: cfi_cmdset_0002: fix do_write_buffer() timeout error
mtd: denali: use 8 bytes for READID command
mtd/ftl: fix the double free of the buffers allocated in build_maps()
mtd: phram: Fix whitespace issues
mtd: spi-nor: add support for EON EN25QH128
mtd: cfi_cmdset_0002: Add support for locking OTP memory
mtd: cfi_cmdset_0002: Add support for writing OTP memory
mtd: cfi_cmdset_0002: Invalidate cache after entering/exiting OTP memory
mtd: cfi_cmdset_0002: Add support for reading OTP
mtd: spi-nor: add support for flag status register on Micron chips
mtd: Account for BBT blocks when a partition is being allocated
...
This merge window brings a good size of cleanups on various
platforms. Among the bigger ones:
* Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
lacked active support for quite a while, and after asking around nobody
showed interest in keeping them around. If needed, they could be
resurrected in the future but it's more likely that we would prefer
reintroduction of them as DT and multiplatform-enabled platforms
instead.
* OMAP4 controller code register define diet. They defined a lot of registers
that were never actually used, etc.
* Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
to drivers/soc so it can be shared with 64-bit code. This also converts them
over to traditional driver models where possible.
* Removal of legacy gpio-samsung driver, since the last users have been
removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some misc
cleanups, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=gbcE
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 3.17. It contains:
- misc Cavium Octeon, BCM47xx, BCM63xx and Alchemy updates
- MIPS ptrace updates and cleanups
- various fixes that will also go to -stable
- a number of cleanups and small non-critical fixes.
- NUMA support for the Loongson 3.
- more support for MSA
- support for MAAR
- various FP enhancements and fixes"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (139 commits)
MIPS: jz4740: remove unnecessary null test before debugfs_remove
MIPS: Octeon: remove unnecessary null test before debugfs_remove_recursive
MIPS: ZBOOT: implement stack protector in compressed boot phase
MIPS: mipsreg: remove duplicate MIPS_CONF4_FTLBSETS_SHIFT
MIPS: Bonito64: remove a duplicate define
MIPS: Malta: initialise MAARs
MIPS: Initialise MAARs
MIPS: detect presence of MAARs
MIPS: define MAAR register accessors & bits
MIPS: mark MSA experimental
MIPS: Don't build MSA support unless it can be used
MIPS: consistently clear MSA flags when starting & copying threads
MIPS: 16 byte align MSA vector context
MIPS: disable preemption whilst initialising MSA
MIPS: ensure MSA gets disabled during boot
MIPS: fix read_msa_* & write_msa_* functions on non-MSA toolchains
MIPS: fix MSA context for tasks which don't use FP first
MIPS: init upper 64b of vector registers when MSA is first used
MIPS: save/disable MSA in lose_fpu
MIPS: preserve scalar FP CSR when switching vector context
...
This patch changes the static memory controller registers to offsets
from base, prefixes them with AU1000_ to avoid silent failures due to
changed addresses and introduces helpers to access them.
No functional changes, comparing assembly of a few select functions shows
no differences.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7463/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the _safe variant because we're iterating over a list where items get
deleted and freed.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch fixes the issue that on very large UBI volumes
UBI block does not work correctly.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
There's no need to set the disk capacity with the mutex held, so this
commit takes the variable setting out of the mutex. This simplifies
the disk capacity fix for very large volumes in a follow up commit.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Currently, ubiblock_resize() can fail if the device is not found
in the list. This commit changes the return type, so the function can
return something meaningful on error paths.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
With a flash-based BBT there is no reason to move the Factory Bad
Block Marker from the data area buffer (to where it is mapped by the
GPMI NAND controller) to the OOB buffer. Thus, make this feature
configurable via DT. This is required for the Ka-Ro electronics
platforms.
In the original code 'this->swap_block_mark' was synonymous with
'!GPMI_IS_MX23()', so use the latter at the relevant places.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix the following error, which sometimes happens during the NFC data
transfer:
atmel_nand 80000000.nand: Time out to wait for interrupt: 0x00010000
atmel_nand 80000000.nand: something wrong, No XFR_DONE interrupt comes.
The root cause is that in the interrupt handler, we read the ISR but
only handle one interrupt. If more than one interrupt arrive at the same
time, then the second one will be lost.
During the NFC data transfer. Two NFC interrupts (NFC_CMD_DONE and
NFC_XFR_DONE) may come at the same time.
NFC_CMD_DONE means NFC command is sent, and NFC_XFR_DONE means NFC data
is transferred.
This patch can handle multiple NFC interrupts at the same time. During
the NFC data transfer, we need to wait for two NFC interrupts:
NFC_CMD_DONE and NFC_XFR_DONE.
Also we separate the completion initialization code to a
nfc_prepare_interrupt(), which is paired with nfc_wait_interrupt().
We call nfc_prepare_interrupt() before sending out nfc commands, to make
sure no interrupt lost.
Reported-by: Matthieu CRAPET <Matthieu.CRAPET@ingenico.com>
Tested-by: Matthieu Crapet <Matthieu.Crapet@ingenico.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In nfc_device_ready(), it's more reasonable to check R/B bit in NFC_SR
than waiting for the R/B interrupt. It cost less time.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Tested-by: Matthieu Crapet <Matthieu.Crapet@ingenico.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add a new function to read the NFC status. Meantime, this function will
check if there is any errors in NFC.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Tested-by: Matthieu Crapet <Matthieu.Crapet@ingenico.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If the ecc parameter is not the same as definition, when the
mtd core check these parameters, it will give the error result.
Take the following as an example:
Calculate how many bits can be corrected in one page.
According to the ecc parameters definition,
one page correct bits = (mtd->writesize * ecc->strength) / ecc->size
take the following use case as an example:
mtd->writesize = 2048 bytes
ecc->strength = 4 bytes (for 512 bytes)
before this patch, the ecc->size = 2048, so the result is 4 bytes.
after this patch, the ecc->size = 512, so the result is 16 bytes.
So, align the ecc parameters the same as definition to correct
this kind of error.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add a converter to retrieve NAND timings from an ONFI NAND timing mode.
At the moment, only SDR NAND timings are supported.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
UBI assumes that ubi_attach_info will only contain ubi_ainf_volume
structures for volumes with at least one LEB.
In scanning mode this is true because UBI can nicely create a ubi_ainf_volume
on demand while creating the EBA table.
For fastmap this is not true, the fastmap on-flash structure has a list of
all volumes, the ubi_ainf_volume structures are created from this list.
So it can happen that an empty volume ends up in init_volumes().
We can easely deal with that by looking into ->leb_count too.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
1. Fix UBI fastmap support which we broke in 3.16-rc1 by reversing the
volumes RB-tree sorting criteria.
2. Make sure that we scrub all PEBs where we see bit-flips - we were missing
some of them when the fastmap feature was enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9bjU
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.16-rc6' of git://git.infradead.org/linux-ubifs
Pull UBI fixes from Artem Bityutskiy:
"Two UBI fastmap-related fixes for v3.16:
- fix UBI fastmap support which we broke in 3.16-rc1 by reversing the
volumes RB-tree sorting criteria.
- make sure that we scrub all PEBs where we see bit-flips - we were
missing some of them when the fastmap feature was enabled"
* tag 'upstream-3.16-rc6' of git://git.infradead.org/linux-ubifs:
UBI: fastmap: do not miss bit-flips
UBI: fix the volumes tree sorting criteria
For some NOR flashes, the size of the buffer program has been increased
from 256 bytes to 512 bytes, and so 2ms maximum timeout can may not be
sufficient for all different vendor's NOR flash. There is maximum
timeout information in the CFI area, so we instead of picking a fixed
value, we can calculate this according to the standard CFI parameters
parsed at probe time. If we haven't probed this information, or it is
smaller than 2000us, then specify a minimum value 2000us.
Tested with Micron JS28F512M29EWx and Micron MT28EW512ABA flash devices.
Signed-off-by: Bean Huo <beanhuo@outlook.com>
[Brian: fix up comments, use 'max()']
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The return value from 'ubi_io_read_ec_hdr()' was stored in 'err', not in 'ret'.
This fix makes sure Fastmap-enabled UBI does not miss bit-flip while reading EC
headers, events and scrubs the affected PEBs.
This issue was reported by Coverity Scan.
Artem: improved the commit message.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The Denali NAND driver reads only 5 bytes of ID, but some Hynix and Samsung
have size parameters in the 6th byte. As a result, the page and oob size
for a Hynix H27UAG8T2B were calculated incorrectly and the driver failed to
load.
The solution is to read 8 bytes of ID, as expected by the NAND framework.
Signed-off-by: Graham Moore <grmoore@altera.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
I got the following panic on my fsl p5020ds board.
Unable to handle kernel paging request for data at address 0x7375627379737465
Faulting instruction address: 0xc000000000100778
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=24 CoreNet Generic
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.15.0-next-20140613 #145
task: c0000000fe080000 ti: c0000000fe088000 task.ti: c0000000fe088000
NIP: c000000000100778 LR: c00000000010073c CTR: 0000000000000000
REGS: c0000000fe08aa00 TRAP: 0300 Not tainted (3.15.0-next-20140613)
MSR: 0000000080029000 <CE,EE,ME> CR: 24ad2e24 XER: 00000000
DEAR: 7375627379737465 ESR: 0000000000000000 SOFTE: 1
GPR00: c0000000000c99b0 c0000000fe08ac80 c0000000009598e0 c0000000fe001d80
GPR04: 00000000000000d0 0000000000000913 c000000007902b20 0000000000000000
GPR08: c0000000feaae888 0000000000000000 0000000007091000 0000000000200200
GPR12: 0000000028ad2e28 c00000000fff4000 c0000000007abe08 0000000000000000
GPR16: c0000000007ab160 c0000000007aaf98 c00000000060ba68 c0000000007abda8
GPR20: c0000000007abde8 c0000000feaea6f8 c0000000feaea708 c0000000007abd10
GPR24: c000000000989370 c0000000008c6228 00000000000041ed c0000000fe00a400
GPR28: c00000000017c1cc 00000000000000d0 7375627379737465 c0000000fe001d80
NIP [c000000000100778] .__kmalloc_track_caller+0x70/0x168
LR [c00000000010073c] .__kmalloc_track_caller+0x34/0x168
Call Trace:
[c0000000fe08ac80] [c00000000087e6b8] uevent_sock_list+0x0/0x10 (unreliable)
[c0000000fe08ad20] [c0000000000c99b0] .kstrdup+0x44/0x90
[c0000000fe08adc0] [c00000000017c1cc] .__kernfs_new_node+0x4c/0x130
[c0000000fe08ae70] [c00000000017d7e4] .kernfs_new_node+0x2c/0x64
[c0000000fe08aef0] [c00000000017db00] .kernfs_create_dir_ns+0x34/0xc8
[c0000000fe08af80] [c00000000018067c] .sysfs_create_dir_ns+0x58/0xcc
[c0000000fe08b010] [c0000000002c711c] .kobject_add_internal+0xc8/0x384
[c0000000fe08b0b0] [c0000000002c7644] .kobject_add+0x64/0xc8
[c0000000fe08b140] [c000000000355ebc] .device_add+0x11c/0x654
[c0000000fe08b200] [c0000000002b5988] .add_disk+0x20c/0x4b4
[c0000000fe08b2c0] [c0000000003a21d4] .add_mtd_blktrans_dev+0x340/0x514
[c0000000fe08b350] [c0000000003a3410] .mtdblock_add_mtd+0x74/0xb4
[c0000000fe08b3e0] [c0000000003a32cc] .blktrans_notify_add+0x64/0x94
[c0000000fe08b470] [c00000000039b5b4] .add_mtd_device+0x1d4/0x368
[c0000000fe08b520] [c00000000039b830] .mtd_device_parse_register+0xe8/0x104
[c0000000fe08b5c0] [c0000000003b8408] .of_flash_probe+0x72c/0x734
[c0000000fe08b750] [c00000000035ba40] .platform_drv_probe+0x38/0x84
[c0000000fe08b7d0] [c0000000003599a4] .really_probe+0xa4/0x29c
[c0000000fe08b870] [c000000000359d3c] .__driver_attach+0x100/0x104
[c0000000fe08b900] [c00000000035746c] .bus_for_each_dev+0x84/0xe4
[c0000000fe08b9a0] [c0000000003593c0] .driver_attach+0x24/0x38
[c0000000fe08ba10] [c000000000358f24] .bus_add_driver+0x1c8/0x2ac
[c0000000fe08bab0] [c00000000035a3a4] .driver_register+0x8c/0x158
[c0000000fe08bb30] [c00000000035b9f4] .__platform_driver_register+0x6c/0x80
[c0000000fe08bba0] [c00000000084e080] .of_flash_driver_init+0x1c/0x30
[c0000000fe08bc10] [c000000000001864] .do_one_initcall+0xbc/0x238
[c0000000fe08bd00] [c00000000082cdc0] .kernel_init_freeable+0x188/0x268
[c0000000fe08bdb0] [c0000000000020a0] .kernel_init+0x1c/0xf7c
[c0000000fe08be30] [c000000000000884] .ret_from_kernel_thread+0x58/0xd4
Instruction dump:
41bd0010 480000c8 4bf04eb5 60000000 e94d0028 e93f0000 7cc95214 e8a60008
7fc9502a 2fbe0000 419e00c8 e93f0022 <7f7e482a> 39200000 88ed06b2 992d06b2
---[ end trace b4c9a94804a42d40 ]---
It seems that the corrupted partition header on my mtd device triggers
a bug in the ftl. In function build_maps() it will allocate the buffers
needed by the mtd partition, but if something goes wrong such as kmalloc
failure, mtd read error or invalid partition header parameter, it will
free all allocated buffers and then return non-zero. In my case, it
seems that partition header parameter 'NumTransferUnits' is invalid.
And the ftl_freepart() is a function which free all the partition
buffers allocated by build_maps(). Given the build_maps() is a self
cleaning function, so there is no need to invoke this function even
if build_maps() return with error. Otherwise it will causes the
buffers to be freed twice and then weird things would happen.
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix various whitespace issues.
No functional changes.
Signed-off-by: Rob Ward <robert.ward114@googlemail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This family of chips was long ago supported by the pre-cfi driver.
CFI code tested on several Zaurus SL-5500 (Collie) 2x16 on 32 bit bus.
Function is_LH28F640BF() mimics is_m29ew() from cmdset_0002.c
Buffer write fixes as seen in 2007 patch c/o
Anti Sullin <anti.sullin <at> artecdesign.ee>
http://comments.gmane.org/gmane.linux.ports.arm.kernel/36733
[Brian: this patch is semi-urgent, because the following patch switches
to using CFI detection for a chip which (until now) is unsupported by
the CFI driver
9218310 ARM: 8084/1: sa1100: collie: revert back to cfi_probe
]
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In commit 67a9ad9b8a ("mtd: nand: Warn the user if the selected ECC
strength is too weak"), a check was added to inform the user when the
ECC used for a NAND device is weaker than the recommended ECC
advertised by the NAND chip. However, the warning uses WARN_ON(),
which has two undesirable side-effects:
- It just prints to the kernel log the fact that there is a warning
in this file, at this line, but it doesn't explain anything about
the warning itself.
- It dumps a stack trace which is very noisy, for something that the
user is most likely not able to fix. If a certain ECC used by the
kernel is weaker than the advertised one, it's most likely to make
sure the kernel uses an ECC that is compatible with the one used by
the bootloader, and changing the bootloader may not necessarily be
easy. Therefore, normal users would not be able to do anything to
fix this very noisy warning, and will have to suffer from it at
every kernel boot. At least every time I see this stack trace in my
kernel boot log, I wonder what new thing is broken, just to realize
that it's once again this NAND ECC warning.
Therefore, this commit turns:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at /home/thomas/projets/linux-2.6/drivers/mtd/nand/nand_base.c:4051 nand_scan_tail+0x538/0x780()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.16.0-rc3-dirty #4
[<c000e3dc>] (unwind_backtrace) from [<c000bee4>] (show_stack+0x10/0x14)
[<c000bee4>] (show_stack) from [<c0018180>] (warn_slowpath_common+0x6c/0x8c)
[<c0018180>] (warn_slowpath_common) from [<c001823c>] (warn_slowpath_null+0x1c/0x24)
[<c001823c>] (warn_slowpath_null) from [<c02c50cc>] (nand_scan_tail+0x538/0x780)
[<c02c50cc>] (nand_scan_tail) from [<c0639f78>] (orion_nand_probe+0x224/0x2e4)
[<c0639f78>] (orion_nand_probe) from [<c026da00>] (platform_drv_probe+0x18/0x4c)
[<c026da00>] (platform_drv_probe) from [<c026c1f4>] (really_probe+0x80/0x218)
[<c026c1f4>] (really_probe) from [<c026c47c>] (__driver_attach+0x98/0x9c)
[<c026c47c>] (__driver_attach) from [<c026a8f0>] (bus_for_each_dev+0x64/0x94)
[<c026a8f0>] (bus_for_each_dev) from [<c026bae4>] (bus_add_driver+0x144/0x1ec)
[<c026bae4>] (bus_add_driver) from [<c026cb00>] (driver_register+0x78/0xf8)
[<c026cb00>] (driver_register) from [<c026da5c>] (platform_driver_probe+0x20/0xb8)
[<c026da5c>] (platform_driver_probe) from [<c00088b8>] (do_one_initcall+0x80/0x1d8)
[<c00088b8>] (do_one_initcall) from [<c0620c9c>] (kernel_init_freeable+0xf4/0x1b4)
[<c0620c9c>] (kernel_init_freeable) from [<c049a098>] (kernel_init+0x8/0xec)
[<c049a098>] (kernel_init) from [<c00095f0>] (ret_from_fork+0x14/0x24)
---[ end trace 62f87d875aceccb4 ]---
Into the much shorter, and much more useful:
nand: WARNING: MT29F2G08ABAEAWP: the ECC used on your system is too weak compared to the one required by the NAND chip
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch removes s5pc100 related onenand codes because of no more
support for S5PC100 SoC in mainline.
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for the locking of the one time
programmable (OTP) memory of Micron M29EW devices.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds support for writing the one time programmable (OTP)
memory of Micron M29EW devices.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When the one time programmable (OTP) memory region is entered by
issuing the 0xaa/0x55/0x88 command, the OTP memory occupies the
addresses which are normally used by the first sector of the regular
flash memory. This patch therefore invalidates cache for this
addresses after entering/exiting OTP memory.
This patch also moves the code into separate functions.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The Micron M29EW has a 256 byte one time programmable (OTP) memory.
This patch adds support for reading this memory. This support will be
extended for locking and writing in subsequent patches.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some new Micron flash chips require reading the flag status register to
determine when operations have completed.
Furthermore, chips with multi-die stacks of the 65nm 256Mb QSPI also
require reading the status register before reading the flag status
register.
This patch adds support for the flag status register in the n25q512ax3
and n25q00 Micron QSPI flash chips.
Signed-off-by: Graham Moore <grmoore@altera.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
With the introduction of mtd_block_isreserved(), it's now possible
to fix the bad and reserved block distribution exposed by ecc_stats,
instead of accounting all the bad or reserved blocks as 'bad'.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In addition to mtd_block_isbad(), which checks if a block is bad or
reserved, it's needed to check if a block is reserved only (but not
bad). This commit adds an MTD interface for it, in a similar fashion to
mtd_block_isbad().
While here, fix mtd_block_isbad() so the out-of-bounds checking is done
before the callback check.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
These new sysfs device attributes allow us to retrieve the ECC and bad
block stats by poking a sysfs file, which is often more convenient than
using the ioctl.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
These two function's switch case lack the 'break' that make them always
return error.
Signed-off-by: Ted Juan <ted.juan@gmail.com>
Acked-by: Pekon Gupta <pekon@ti.com>
Cc: <stable@vger.kernel.org> # 3.12.x+
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This driver's suspend/resume hooks are no-ops, so just remove them.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
This is not used by any code now. Just drop it.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use clk_prepare_enable/clk_disable_unprepare to make the driver
work properly with common clock framework.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
These drivers don't need to explicitly initialize their bitflip
thresholds. The comment is no longer correct, since nand_scan_tail()
performs this initialization as of the following commit:
commit ea3b2ea24e
Author: Shmulik Ladkani <shmulik@jungo.com>
Date: Fri Jun 8 18:29:06 2012 +0300
mtd: nand: initialize bitflip_threshold prior to BBT scanning
(It seems there were some parallel efforts on writing/submitting these
drivers, and Shmulik's bug fix.)
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Roland Stigge <stigge@antcom.de>
Commig "604b592 UBI: fix rb_tree node comparison in add_map"
broke fastmap backward compatibility and older fastmap images
cannot be mounted anymore. The reason is that it changes the
volumes RB-tree sorting criteria. This patch fixes the problem.
Artem: re-write the commit message
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Pull vfs updates from Al Viro:
"This the bunch that sat in -next + lock_parent() fix. This is the
minimal set; there's more pending stuff.
In particular, I really hope to get acct.c fixes merged this cycle -
we need that to deal sanely with delayed-mntput stuff. In the next
pile, hopefully - that series is fairly short and localized
(kernel/acct.c, fs/super.c and fs/namespace.c). In this pile: more
iov_iter work. Most of prereqs for ->splice_write with sane locking
order are there and Kent's dio rewrite would also fit nicely on top of
this pile"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (70 commits)
lock_parent: don't step on stale ->d_parent of all-but-freed one
kill generic_file_splice_write()
ceph: switch to iter_file_splice_write()
shmem: switch to iter_file_splice_write()
nfs: switch to iter_splice_write_file()
fs/splice.c: remove unneeded exports
ocfs2: switch to iter_file_splice_write()
->splice_write() via ->write_iter()
bio_vec-backed iov_iter
optimize copy_page_{to,from}_iter()
bury generic_file_aio_{read,write}
lustre: get rid of messing with iovecs
ceph: switch to ->write_iter()
ceph_sync_direct_write: stop poking into iov_iter guts
ceph_sync_read: stop poking into iov_iter guts
new helper: copy_page_from_iter()
fuse: switch to ->write_iter()
btrfs: switch to ->write_iter()
ocfs2: switch to ->write_iter()
xfs: switch to ->write_iter()
...
re-add the perm check (we unified the module param and sysfs checks, but
the module ones were stronger so we weakened them temporarily).
Param parsing gets documented, and also "--" now forces args to be
handed to init (and ignored by the kernel).
Module NX/RO protections get tightened: we now set them before calling
parse_args().
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=IxSN
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Most of this is cleaning up various driver sysfs permissions so we can
re-add the perm check (we unified the module param and sysfs checks,
but the module ones were stronger so we weakened them temporarily).
Param parsing gets documented, and also "--" now forces args to be
handed to init (and ignored by the kernel).
Module NX/RO protections get tightened: we now set them before calling
parse_args()"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
module: set nx before marking module MODULE_STATE_COMING.
samples/kobject/: avoid world-writable sysfs files.
drivers/hid/hid-picolcd_fb: avoid world-writable sysfs files.
drivers/staging/speakup/: avoid world-writable sysfs files.
drivers/regulator/virtual: avoid world-writable sysfs files.
drivers/scsi/pm8001/pm8001_ctl.c: avoid world-writable sysfs files.
drivers/hid/hid-lg4ff.c: avoid world-writable sysfs files.
drivers/video/fbdev/sm501fb.c: avoid world-writable sysfs files.
drivers/mtd/devices/docg3.c: avoid world-writable sysfs files.
speakup: fix incorrect perms on speakup_acntsa.c
cpumask.h: silence warning with -Wsign-compare
Documentation: Update kernel-parameters.tx
param: hand arguments after -- straight to init
modpost: Fix resource leak in read_dump()
- refactor m25p80.c driver for use as a general SPI NOR framework for other
drivers which may speak to SPI NOR flash without providing full SPI support
(i.e., not part of drivers/spi/)
- new Freescale QuadSPI driver (utilizing new SPI NOR framework)
- updates for the STMicro "FSM" SPI NOR driver
- fix sync/flush behavior on mtd_blkdevs
- fixup subpage write support on a few NAND drivers
- correct the MTD OOB test for odd-sized OOB areas
- add BCH-16 support for OMAP NAND
- fix warnings and trivial refactoring
- utilize new ECC DT bindings in pxa3xx NAND driver
- new LPDDR NVM driver
- address a few assorted bugs caught by Coverity
- add new imx6sx support for GPMI NAND
- use a bounce buffer for NAND when non-DMA-able buffers are used
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6UIq
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20140610' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
- refactor m25p80.c driver for use as a general SPI NOR framework for
other drivers which may speak to SPI NOR flash without providing full
SPI support (i.e., not part of drivers/spi/)
- new Freescale QuadSPI driver (utilizing new SPI NOR framework)
- updates for the STMicro "FSM" SPI NOR driver
- fix sync/flush behavior on mtd_blkdevs
- fixup subpage write support on a few NAND drivers
- correct the MTD OOB test for odd-sized OOB areas
- add BCH-16 support for OMAP NAND
- fix warnings and trivial refactoring
- utilize new ECC DT bindings in pxa3xx NAND driver
- new LPDDR NVM driver
- address a few assorted bugs caught by Coverity
- add new imx6sx support for GPMI NAND
- use a bounce buffer for NAND when non-DMA-able buffers are used
* tag 'for-linus-20140610' of git://git.infradead.org/linux-mtd: (77 commits)
mtd: gpmi: add gpmi support for imx6sx
mtd: maps: remove check for CONFIG_MTD_SUPERH_RESERVE
mtd: bf5xx_nand: use the managed version of kzalloc
mtd: pxa3xx_nand: make the driver work on big-endian systems
mtd: nand: omap: fix omap_calculate_ecc_bch() for-loop error
mtd: nand: r852: correct write_buf loop bounds
mtd: nand_bbt: handle error case for nand_create_badblock_pattern()
mtd: nand_bbt: remove unused variable
mtd: maps: sc520cdp: fix warnings
mtd: slram: fix unused variable warning
mtd: pfow: remove unused variable
mtd: lpddr: fix Kconfig dependency, for I/O accessors
mtd: nand: pxa3xx: Add supported ECC strength and step size to the DT binding
mtd: nand: pxa3xx: Use ECC strength and step size devicetree binding
mtd: nand: pxa3xx: Clean pxa_ecc_init() error handling
mtd: nand: Warn the user if the selected ECC strength is too weak
mtd: nand: omap: Documentation: How to select correct ECC scheme for your device ?
mtd: nand: omap: add support for BCH16_ECC - NAND driver updates
mtd: nand: omap: add support for BCH16_ECC - ELM driver updates
mtd: nand: omap: add support for BCH16_ECC - GPMC driver updates
...
condition between the mmap page fault path and fsync. Another just removes a
bogus assertion from the UBIFS memory shrinker.
UBIFS also started honoring the MS_SILENT mount flag, so now it won't print
many I/O errors when user-space just tries to probe for the FS.
Rest of the changes are rather minor UBI/UBIFS fixes, improvements, and
clean-ups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CP7Z
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.16-rc1-v2' of git://git.infradead.org/linux-ubifs
Pull UBIFS updates from Artem Bityutskiy:
"This contains several UBIFS fixes. One of them fixes a race condition
between the mmap page fault path and fsync. Another just removes a
bogus assertion from the UBIFS memory shrinker.
UBIFS also started honoring the MS_SILENT mount flag, so now it won't
print many I/O errors when user-space just tries to probe for the FS.
Rest of the changes are rather minor UBI/UBIFS fixes, improvements,
and clean-ups"
* tag 'upstream-3.16-rc1-v2' of git://git.infradead.org/linux-ubifs:
UBIFS: Add an assertion for clean_zn_cnt
UBIFS: respect MS_SILENT mount flag
UBIFS: Remove incorrect assertion in shrink_tnc()
UBIFS: fix debugging check
UBIFS: add missing ui pointer in debugging code
UBI: block: Fix error path on alloc_workqueue failure
UBIFS: Fix dump messages in ubifs_dump_lprops
UBI: fix rb_tree node comparison in add_map
UBIFS: Remove unused variables in ubifs_budget_space
UBI: weaken the 'exclusive' constraint when opening volumes to rename
UBIFS: fix an mmap and fsync race condition
Aaron Sierra