Tom Lendacky says:
====================
amd-xgbe: AMD XGBE driver updates 2016-02-12
The following updates and fixes are included in this driver update series:
- Disable VLAN filtering in promiscuous mode
- Change from using napi_complete to napi_complete_done
- Use __napi_schedule_irqoff when running in interrupt context
- Verify ethtool speed setting is valid for the selected speedset
- Enable PFC based on the pfc_en setting
- Fix the mapping of priorities to traffic classes
- Do traffic class setup when DCB nl callbacks are invoked
- Check Rx queue fifos before stopping Rx queue DMA
- Switch from disable_irq to masking interrupts for auto-negotiation
This patch series is based on net-next.
Changes from v1:
- Removed #ifndef and #define of CRCPOLY_LE as part of the patch to
disable VLAN filtering in promiscuous mode
- Reworked changes to xgbe_setup_tc to resolve conflicts with commit
16e5cc6471 (net: rework setup_tc ndo op to consume general tc operand)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the auto-negotiation interrupt handling disables the irq
instead of masking off the interrupts. This was done because the phy
library was originally used to read and write the PCS registers, which
could not be performed in interrupt context. Now that the phy library is
no longer used to read and write the PCS registers the interrupts can be
masked off in the interrupt service routine eliminating the need to call
disable_irq/enable_irq. This also requires changing the protection mutex
to a spinlock.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check to be sure that the Rx queue fifos are empty before stopping the
Rx DMA channels.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the netdev traffic class setup is only performed when invoked
through the ndo_setup_tc interface. However, the same setup should be
performed when the dcbnl interface (ieee_setets) is invoked. Rework the
netdev traffic class setup to be invokable through either interface and
also provide the priority to traffic class mapping if available.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver is checking the pfc_en field of the ieee_pfc structure to
determine whether to associate a priority with a traffic class. This is
incorrect since the pfc_en field is for determining if PFC is enabled
for a traffic class.
The association of priority to traffic class does not depend on whether
the traffic class is enabled for PFC, so remove that check. Also, the
mapping of priorities to traffic classes should be done when configuring
the traffic classes and not the PFC support so move the priority to traffic
class association from xgbe_config_dcb_pfc to xgbe_config_dcb_tc.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the PFC flow control is enabled on all traffic classes if
one or more traffic classes request it. The PFC enable setting of the
traffic class should be used to determine whether to enable or disable
flow control for the traffic class.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using ethtool to set the speed for the device, verify that the
specified speed is valid within the active speedset.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change from calling __napi_schedule to __napi_schedule_irqoff when running
in interrupt context or when called by netpoll with interrupts already
disabled. The Tx timer function will continue to use __napi_schedule.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change from using napi_complete to napi_complete_done to allow for the
use of gro_flush_timeout in tuning network processing.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the hardware is placed in promiscuous mode it will still perform
VLAN filtering and therefore may not pass all packets to the driver.
Disable all VLAN filtering when entering promiscuous mode and restore
VLAN filtering upon exit from promiscuous mode. In order to avoid adding
forward declarations, move the VLAN related functions earlier in the
file.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use IFF_NO_QUEUE to indicate that a device can run without a qdisc.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull block fixes from Jens Axboe:
"A collection of fixes from the past few weeks that should go into 4.5.
This contains:
- Overflow fix for sysfs discard show function from Alan.
- A stacking limit init fix for max_dev_sectors, so we don't end up
artificially capping some use cases. From Keith.
- Have blk-mq proper end unstarted requests on a dying queue, instead
of pushing that to the driver. From Keith.
- NVMe:
- Update to Kconfig description for NVME_SCSI, since it was
vague and having it on is important for some SUSE distros.
From Christoph.
- Set of fixes from Keith, around surprise removal. Also kills
the no-merge flag, so it supports merging.
- Set of fixes for lightnvm from Matias, Javier, and Wenwei.
- Fix null_blk oops when asked for lightnvm, but not available. From
Matias.
- Copy-to-user EINTR fix from Hannes, fixing a case where SG_IO fails
if interrupted by a signal.
- Two floppy fixes from Jiri, fixing signal handling and blocking
open.
- A use-after-free fix for O_DIRECT, from Mike Krinkin.
- A block module ref count fix from Roman Pen.
- An fs IO wait accounting fix for O_DSYNC from Stephane Gasparini.
- Smaller reallo fix for xen-blkfront from Bob Liu.
- Removal of an unused struct member in the deadline IO scheduler,
from Tahsin.
- Also from Tahsin, properly initialize inode struct members
associated with cgroup writeback, if enabled.
- From Tejun, ensure that we keep the superblock pinned during cgroup
writeback"
* 'for-linus' of git://git.kernel.dk/linux-block: (25 commits)
blk: fix overflow in queue_discard_max_hw_show
writeback: initialize inode members that track writeback history
writeback: keep superblock pinned during cgroup writeback association switches
bio: return EINTR if copying to user space got interrupted
NVMe: Rate limit nvme IO warnings
NVMe: Poll device while still active during remove
NVMe: Requeue requests on suspended queues
NVMe: Allow request merges
NVMe: Fix io incapable return values
blk-mq: End unstarted requests on dying queue
block: Initialize max_dev_sectors to 0
null_blk: oops when initializing without lightnvm
block: fix module reference leak on put_disk() call for cgroups throttle
nvme: fix Kconfig description for BLK_DEV_NVME_SCSI
kernel/fs: fix I/O wait not accounted for RW O_DSYNC
floppy: refactor open() flags handling
lightnvm: allow to force mm initialization
lightnvm: check overflow and correct mlc pairs
lightnvm: fix request intersection locking in rrpc
lightnvm: warn if irqs are disabled in lock laddr
...
Pull drm fixes from Dave Airlie:
"This has two main sets of fixes:
- A bunch of Exynos fixes, mainly for their MIC component.
- vblank regression fixes from Mario, apparantly some changes in 4.4
caused some vblank breakage on radeon/nouveau, this set fixes all
the issues seen.
There is also a revert of one of the MST changse, that I was
overzealous in including, that broke 30" MST monitors, and two qxl
fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/qxl: fix erroneous return value
drm/nouveau/display: Enable vblank irqs after display engine is on again.
drm/radeon/pm: Handle failure of drm_vblank_get.
drm: Fix treatment of drm_vblank_offdelay in drm_vblank_on() (v2)
drm: Fix drm_vblank_pre/post_modeset regression from Linux 4.4
drm: Prevent vblank counter bumps > 1 with active vblank clients. (v2)
drm: No-Op redundant calls to drm_vblank_off() (v2)
drm/qxl: use kmalloc_array to alloc reloc_info in qxl_process_single_command
Revert "drm/dp/mst: change MST detection scheme"
drm/exynos/decon: fix disable clocks order
drm/exynos: fix incorrect cpu address for dma_mmap_attrs()
drm/exynos: exynos5433_decon: fix wrong state in decon_vblank_enable
drm/exynos: exynos5433_decon: fix wrong state assignment in decon_enable
drm/exynos: dsi: restore support for drm bridge
drm/exynos: mic: make all functions static
drm/exynos: mic: convert to component framework
drm/exynos: mic: use devm_clk interface
drm/exynos: fix types for compilation on 64bit architectures
drm/exynos: ipp: fix incorrect format specifiers in debug messages
drm/exynos: depend on ARCH_EXYNOS for DRM_EXYNOS
The first is something that has come up a few times and has been
worked out individually, but it's come up now enough that the problem
should be generic. Tracepoints are protected by RCU sched. There are
several tracepoints within core infrastructure like kfree().
If a tracepoint is called when the CPU is going down, or when it's
coming up but has yet to be recognized by RCU, a RCU warning is
triggered. This is a true bug as that tracepoint is not protected by
RCU. Usually, this is taken care of by testing for cpu online as
a tracepoint condition. But as this is happening more often, moving
it from a individual tracepoint to a check in the tracepoint infrastructure
is more robust.
Note, there is now a duplicate of a cpu online test, because this update
does not remove the individual checks. But the overhead is small enough
that the removal can be done in another release.
The second change is strange linker breakage due to the branch tracer's
builtin_constant_p() check failing, and treating the condition as a
variable instead of a constant. Arnd Bergmann found that this can be
fixed by testing !!(cond) instead of just (cond).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWw2vTAAoJEKKk/i67LK/8vkMIAI+Fx+S9sCeWVGp4VZ3DKH9K
DibRD/2KREZe1AjYEU8ZAgo+VsFzW8OHiI1TI/1jP61YkiQSIhu6kVdPCoLG5buy
8WwiKEQ94VWC1hbPOiiq3K7THEu+M8zuFdU3+odS8E3sXIGqKPKQ3iFwwfTVHI6o
/cMTuefqsxo/hj8VwwaZdwlgWwLltM8sR040auTTEsqBLZ7D1q0aCyBrnju3FtBt
uSIPK91d92ANkpq3ELDihxBa41XSEahYgGm/ozewjHwpooWvIQz4tpGaxxkyltuE
RzeYBrM5LNBQUaXZ6C6jAdL0Y+bukS2MdNUjv8U6LwKbUvQoLuYteGEQ9g/m+mE=
=8LDX
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-v4.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"This includes two fixes.
The first is something that has come up a few times and has been
worked out individually, but it's come up now enough that the problem
should be generic. Tracepoints are protected by RCU sched. There are
several tracepoints within core infrastructure like kfree(). If a
tracepoint is called when the CPU is going down, or when it's coming
up but has yet to be recognized by RCU, a RCU warning is triggered.
This is a true bug as that tracepoint is not protected by RCU.
Usually, this is taken care of by testing for cpu online as a
tracepoint condition. But as this is happening more often, moving it
from a individual tracepoint to a check in the tracepoint
infrastructure is more robust.
Note, there is now a duplicate of a cpu online test, because this
update does not remove the individual checks. But the overhead is
small enough that the removal can be done in another release.
The second change is strange linker breakage due to the branch
tracer's builtin_constant_p() check failing, and treating the
condition as a variable instead of a constant. Arnd Bergmann found
that this can be fixed by testing !!(cond) instead of just (cond)"
* tag 'trace-fixes-v4.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix freak link error caused by branch tracer
tracepoints: Do not trace when cpu is offline
This commit converts commit b499ffb0a2 ("i40e: Look up MAC address in
Open Firmware or IDPROM") to use eth_platform_get_mac_address()
added by commit c7f5d10549 ("net: Add eth_platform_get_mac_address()
helper.")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We get this right for queue_discard_max_show but not max_hw_show. Follow the
same pattern as queue_discard_max_show instead so that we don't truncate.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The X722 can support automatic rule eviction for automatically added
flow director rules. Feature is (should be) disabled by default.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes sure we check the GENEVE offload capable flag before
we attempt offload.
It also enables the Capability for XL710/X710 devices with FW API
version higher than 1.4
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Assign the i40e_pf structure directly instead of using a large memcpy,
which avoids a sparse warning and lets the compiler optimize the copy
since it knows the size of the structure in advance.
Change-ID: I17604e23be2616521eb760290befcb767b52b3f7
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver already counted allocation errors, so print
them as part of the ethtool -S output. Useful for debugging
if your system is having trouble making memory available for
the driver.
Change-ID: I83839fa86e81e6d80f03b917c88dd3ef9a64dde0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PHY interrupt mask bits mask out the events we don't want,
so we need to negate the bitmask of events we want.
Change-ID: I273244da5a8d285b6abc84fd68a90f1e6fa0393e
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements necessary functions related to port
mirroring features such as add/delete mirror rule, function
to set promiscuous VLAN mode for VSI if mirror rule_type is
"VLAN Mirroring".
Change-ID: Iaf513fd5f188f99dcb977b48f99e73185dfddc40
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was being called by VLAN, bonding, teaming operations
that expected to be able to hold locks like rcu_read_lock().
This causes the driver to be held to the requirement to not sleep,
and was found by the kernel debug options for checking sleep
inside critical section, and the locking validator.
Change-ID: Ibc68c835f5ffa8ffe0638ffe910a66fc5649a7f7
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Nelson, Shannon <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The sync_vsi_filter function was allocating memory in such
a way that it could sleep (GFP_KERNEL) which was causing a problem
when called by the team driver under rcu_read_lock(), which cannot
be held while sleeping. Found with lockdep.
Change-ID: I4e59053cb5eedcf3d0ca151715be3dc42a94bdd5
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't bother trying to set up a TSO if the skb->ip_summed is not
set to CHECKSUM_PARTIAL.
Change-ID: I6495b3568e404907a2965b48cf3e2effa7c9ab55
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver was using an offset based off a DMA handle while mapping and
unmapping using sync_single_range_for[cpu|device], where it should
be using DMA handle (returned from alloc_coherent) and the offset of the
memory to be sync'd.
Change-ID: I208256565b1595ff0e9171ab852de06b997917c6
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Nelson, Shannon <shannon.nelson@intel.com>
Reviewed-by: Williams, Mitch A <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Missing space in comment, fixed.
Change-ID: I8cdf3ce5994b4a97dcc3eeb33422533918546667
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The probe routine already had a u32 val declared, no need
to do it again. Found by W=2 compile.
Change-ID: Id7b65f6d0ef6bb71067d0557f5be0202b6d8741e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The cpsw-phy-sel driver supports only MII, RMII, and RGMII PHY modes,
and silently handled any other values as if MII was specified. In a
case where the PHY mode was incorrectly specified, or a bug elsewhere,
there would be no indication of a problem. If MII was the correct mode,
then this will go unnoticed, otherwise the symptom will be a failure
to transmit/receive data over the RMII/RGMII link.
Add a dev_warn() to make this condition obvious and provide a
breadcrumb to follow.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David Rivshin <drivshin@allworx.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_config_init() masked out pause flags set in phy driver structure.
Pause flags needs to be preserved in phydev->supported &
phydev->advertising.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz says:
====================
Mellanox 10/40G mlx4 driver fixes for 4.5-rc
Bunch of fixes from the team to the mlx4 Eth and core drivers.
Series generated against net commit aac8d3c "qmi_wwan: add "4G LTE usb-modem U901""
Please push patches 1,2 and 6 to -stable as well
changes from v0:
- handled another wrongly accounted HW counter in patch #1 (Rick)
- fixed coding style issues in patch #4 (Sergei)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It's forbidden to manually change dev->features in run-time. Currently, this is
done in the driver to make sure that GSO_UDP_TUNNEL is advertized only when
VXLAN tunnel is set. However, since the stack actually does features intersection
with hw_enc_features, we can safely revert to advertizing features early when
registering the netdevice.
Fixes: f4a1edd561 ('net/mlx4_en: Advertize encapsulation offloads [...]')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
problem description:
The current code sets UAR page size equal to system page size.
The ConnectX-3 and ConnectX-3 Pro HWs require minimum 128 UAR pages.
The mlx4 kernel drivers are not loaded if there is less than 128 UAR pages.
solution:
Always set UAR page to 4KB. This allows more UAR pages if the OS
has PAGE_SIZE larger than 4KB. For example, PowerPC kernel use 64KB
system page size, with 4MB uar region, there are 4MB/2/64KB = 32
uars (half for uar, half for blueflame). This does not meet minimum 128
UAR pages requirement. With 4KB UAR page, there are 4MB/2/4KB = 512 uars
which meet the minimum requirement.
Note that only codes in mlx4_core that deal with firmware know that uar
page size is 4KB. Codes that deal with usr page in cq and qp context
(mlx4_ib, mlx4_en and part of mlx4_core) still have the same assumption
that uar page size equals to system page size.
Note that with this implementation, on 64KB system page size kernel, there
are 16 uars per system page but only one uars is used. The other 15
uars are ignored because of the above assumption.
Regarding SR-IOV, mlx4_core in hypervisor will set the uar page size
to 4KB and mlx4_core code in virtual OS will obtain the uar page size from
firmware.
Regarding backward compatibility in SR-IOV, if hypervisor has this new code,
the virtual OS must be updated. If hypervisor has old code, and the virtual
OS has this new code, the new code will be backward compatible with the
old code. If the uar size is big enough, this new code in VF continues to
work with 64 KB uar page size (on PowerPc kernel). If the uar size does not
meet 128 uars requirement, this new code not loaded in VF and print the same
error message as the old code in Hypervisor.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PCI channel could go offline during reset due to EEH. Don't bug on in
this case, the error is recoverable.
Fixes: f6bc11e426 ('net/mlx4_core: Enhance the catas flow to support device reset')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error flow in procedure handle_existing_counter() is wrong.
The procedure should exit after encountering the error, not continue
as if everything is OK.
Fixes: 68230242cd ('net/mlx4_core: Add port attribute when tracking counters')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, the shift value used for time-stamping was constant and didn't
depend on the HW chip frequency. Change that to take the frequency into account
and calculate the maximal value in cycles per wraparound of ten seconds. This
time slot was chosen since it gives a good accuracy in time synchronization.
Algorithm for shift value calculation:
* Round up the maximal value in cycles to nearest power of two
* Calculate maximal multiplier by division of all 64 bits set
to above result
* Then, invert the function clocksource_khz2mult() to get the shift from
maximal mult value
Fixes: ec693d4701 ('net/mlx4_en: Add HW timestamping (TS) support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RdropOvflw counts overrun of HW buffer, therefore should
be used for rx_fifo_errors only.
Currently RdropOvflw counter is mistakenly also set into
rx_missed_errors and rx_over_errors too, which makes the
device total dropped packets accounting to show wrong results.
Fix that. Use it for rx_fifo_errors only.
Fixes: c27a02cd94 ('mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC')
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report that driver supports IB_PMA_CLASS_CAP_EXT_WIDTH in respond for
IB_MGMT_CLASS_PERF_MGMT mad with IB_PMA_CLASS_PORT_INFO attr id.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When attribute IB_PMA_PORT_COUNTERS_EXT is set, we now return 64 bit
values for the counters.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Today ocrdma driver defer arming the CQ till poll is called.
This was used to prevent calling poll-cq on an armed CQ.
Recently a set of new CQ API has been introduced into the linux
kernel. The implementation of this API guarantees that a given
CQ is never armed before calling poll on it. Most of the kernel
ULPs have already moved to use this new API or have a code where
poll is called before arming the CQ.
Thus, the above workaround in ocrdma is not needed anymore.
This patch removes the additional logic to deffer arm till poll
is called. This patch adds a simple scheme where ib_req_notify_cq()
will actually arm the cq.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-02-16
This series contains updates to i40e/i40evf only.
Shannon adds flags to MAC allocation requests to signify that the MAC VLAN
filters should come from the shared resource pool. Added a new "set switch
config" admin queue command and the new Cisco VXLAN-GPE cloud tunnel type
for the admin queue commands. Added more detail to the NVM update debug
message in order to see the full ethtool request data. Also added a few
more bits of netdev data into the debugfs output for dump VSI.
Pandi fixes the width of two datatypes which were being declared a different
size from what they are assigned.
Anjali fixes an issue where we were not doing write-back on interrupt
throttle for legacy case in x722.
Mitch adds a counter for ARQ overflows since sometimes an ever-growing
number indicates that something bad is happening. Also added 20G speed for
Tx bandwidth calculations.
Jesse refactors the DCB function based on a community suggestion to change
the multi-level if statement into a switch statement. Cleans up VF device
IDs in the PF, since it does not need to know them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend says:
====================
tc offload for cls_u32 on ixgbe
This extends the setup_tc framework so it can support more than just
the mqprio offload and push other classifiers and qdiscs into the
hardware. The series here targets the u32 classifier and ixgbe
driver. I worked out the u32 classifier because it is protocol
oblivious and aligns with multiple hardware devices I have access
to. I did an initial implementation on ixgbe because (a) I have one
in my box (b) its a stable driver and (c) it is relatively simple
compared to the other devices I have here but still has enough
flexibility to exercise the features of cls_u32.
I intentionally limited the scope of this series to the basic
feature set. Specifically this uses a 'big hammer' feature bit
to do the offload or not. If the bit is set you get offloaded rules
if it is not then rules will not be offloaded. If we can agree on
this patch series there are some more patches on my queue we can
talk about to make the offload decision per rule using flags similar
to how we do l2 mac updates. Additionally the error strategy can
be improved to be hard aborting, log and continue, etc. I think
these are nice to have improvements but shouldn't block this series.
Also by adding get_parse_graph and set_parse_graph attributes as
in my previous flow_api work we can build programmable devices
and programmatically learn when rules can or can not be loaded
into the hardware. Again future work.
... v3 includes a couple style fixups suggested by Jiri and a
quick fix to ixgbe to check features flag and not dev_features
flag the latter being always set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures ixgbe will not try to offload hash tables from the
u32 module. The device class does not currently support this so until
it is enabled just abort on these tables.
Interestingly the more flexible your hardware is the less code you
need to implement to guard against these cases.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds initial support for offloading the u32 tc classifier. This
initial implementation only implements a few base matches and actions
to illustrate the use of the infrastructure patches.
However it is an interesting subset because it handles the u32 next
hdr logic to correctly map tcp packets from ip headers using the ihl
and protocol fields. After this is accepted we can extend the match
and action fields easily by updating the model header file.
Also only the drop action is supported initially.
Here is a short test script,
#tc qdisc add dev eth4 ingress
#tc filter add dev eth4 parent ffff: protocol ip \
u32 ht 800: order 1 \
match ip dst 15.0.0.1/32 match ip src 15.0.0.2/32 action drop
<-- hardware has dst/src ip match rule installed -->
#tc filter del dev eth4 parent ffff: prio 49152
#tc filter add dev eth4 parent ffff: protocol ip prio 99 \
handle 1: u32 divisor 1
#tc filter add dev eth4 protocol ip parent ffff: prio 99 \
u32 ht 800: order 1 link 1: \
offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 6 ff
#tc filter add dev eth4 parent ffff: protocol ip \
u32 ht 1: order 3 match tcp src 23 ffff action drop
<-- hardware has tcp src port rule installed -->
#tc qdisc del dev eth4 parent ffff:
<-- hardware cleaned up -->
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds an ixgbe data structure that is used to determine what
headers:fields can be matched and in what order they are supported.
For hardware devices this can be a bit tricky because typically
only pre-programmed (firmware, ucode, rtl) parse graphs will be
supported and we don't yet have an interface to change these from
the OS. So its sort of a you get whatever your friendly vendor
provides affair at the moment.
In the future we can add the get routines and set routines to
update this data structure. One interesting thing to note here
is the data structure here identifies ethernet, ip, and tcp
fields without having to hardcode them as enumerations or use
other identifiers.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a helper function drivers can use to learn if the
action type is a drop action.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Its useful to turn off the qdisc offload feature at a per device
level. This gives us a big hammer to enable/disable offloading.
More fine grained control (i.e. per rule) may be supported later.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller