base index is not used anymore and so remove it.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The user ratekbs of MCS15 ShortGI is incorrect and can not be lesser
than MCS15 rate. This incorrect rate may affect switching to higher
rates as the rate control algorithm always finds MCS15 is better
than MCS15 ShortGI and results in lower throughput. Fix this by
feeding the correct user ratekbs for MCS15 ShortGI rate.
This issue affects 3 stream case very badly as the 3 stream rates are
not used at all once we scale down to MCS15 from 3 stream rates.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds 3 stream rate control support for AR938X family
chipsets which supports 3 streams.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
replace valid and valid_single_stream in rate table with bit masks
and reorganize the code so adding 3x3 rate control would be easier.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 already masks the HT sta capabilities based on hardware support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The following commit added an entry in 11na and 11ng rate
table but missed to update its rate count field. This
inconsistency between the rate count and the actual number
of rates in the table will leave out the final rate entry
(mcs15 with half gi in ht40) while forming the valid
rate indices. Not having mcs15+shortGI in ht40 will have
a performance impact (on max throughput) of about 10% both
in nght40 and naht40 mode.
Author: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Date: Thu May 13 18:42:38 2010 -0700
ath9k: Enable Short GI in 20 Mhz for ar9287 and later chips
This patch enables short GI rx at all rates and tx at mcs15
for 20 Mhz channel width also.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables short GI rx at all rates and tx at mcs15
for 20 Mhz channel width also.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LDPC is enabled by the rate control if the its determined
that the target peer supports LDPC. We would have already
intersected the HT capabilities so if our peer supports
LDPC so do we.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Currently the rate control tx status update gets called for every
subframe of an A-MPDU, and ath9k marks the frame with the relevant
status update with an internal flag. This not suitable for rate control
algorithms using the standard mac80211 rate control API, so fix this by
using IEEE80211_TX_STAT_AMPDU for marking the correct frames that
should be processed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handling HT configuration changes involved setting the channel
with the new HT parameters and then issuing a rate_update()
notification to the driver.
This behavior changed after the off-channel changes. Now, the channel
is not updated with the new HT params in enable_ht() - instead, it
is now done when the scan work terminates. This results in the driver
depending on stale information, defaulting to non-HT mode always.
Fix this by passing the new channel type to the driver.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When selecting the tx fallback rate, rc.c used a separate variable
'nrix' for storing the next rate index, however it did not use that as
reference for further rate index lowering. Because of that, it ended up
reusing the same rate for multiple multi-rate retry stages, thus
decreasing delivery probability under changing link conditions.
This patch removes the separate (unnecessary) variable and fixes
fallback the way it was intended to work.
This should result in increased throughput and better link stability.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k currently forces hw->max_rate_tries to 4 to work around rate
control inefficiencies. This has some negative side effects, such as
rate_control_send_low also using a maximum of 4 tries, which could
negatively affect reliability of unicast management frames.
This patch pushes the retry limit to the rate control instead, and
allows it to use more tries on the last stage to prevent unnecessary
packet loss.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Atheros single stream AR9285 and AR9271 have half the PCU TX FIFO
buffer size of that of dual stream devices. Dual stream devices
have a max PCU TX FIFO size of 8 KB while single stream devices
have 4 KB. Single stream devices have an issue though and require
hardware only to use half of the amount of its capable PCU TX FIFO
size, 2 KB and this requires a change in software.
Technically a change would not have been required (except for frame
burst considerations of 128 bytes) if these devices would have been
able to use the full 4 KB of the PCU TX FIFO size but our systems
engineers recommend 2 KB to be used only. We enforce this through
software by reducing the max frame triggger level to 2 KB.
Fixing the max frame trigger level should then have a few benefits:
* The PER will now be adjusted as designed for underruns when the
max trigger level is reached. This should help alleviate the
bus as the rate control algorithm chooses a slower rate which
should ensure frames are transmitted properly under high system
bus load.
* The poll we use on our TX queues should now trigger and work
as designed for single stream devices. The hardware passes
data from each TX queue on the PCU TX FIFO queue respecting each
queue's priority. The new trigger level ensures this seeding of
the PCU TX FIFO queue occurs as designed which could mean avoiding
false resets and actually reseting hw correctly when a TX queue
is indeed stuck.
* Some undocumented / unsupported behaviour could have been triggered
when the max trigger level level was being set to 4 KB on single
stream devices. Its not clear what this issue was to me yet.
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Cc: Bennyam Malavazi <bennyam.malavazi@atheros.com>
Cc: Stephen Chen <stephen.chen@atheros.com>
Cc: Shan Palanisamy <shan.palanisamy@atheros.com>
Cc: Paul Shaw <paul.shaw@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove some fields from struct ath_rate_table that are now unused.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes ath9k to pass proper MCS indexes and flags
between the RC and the rest of the driver code.
sc->cur_rate_table remains, as it's used by the RC code internally,
but the rest of the driver code no longer uses it, so a potential
new RC for ath9k would not have to update it.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The entire aggregation code currently operates on the
hw pointer and station addresses, but that needs to
change to make stations purely per-vif; As one step
preparing for that make the aggregation code callable
with the station, or by the combination of virtual
interface and station address.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the need for separately allocated private tx info
data in ath9k and brings the driver one small step closer to using the
mac80211 rate control API properly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/usb/cdc_ether.c
All CDC ethernet devices of type USB_CLASS_COMM need to use
'&mbm_info'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch e43419f9:
ath9k: downgrade assert in rc.c for invalid rate
downgraded an ASSERT to a WARN_ON() but also misplaced a
semicolon at the end of the second check. What this did
was force the rate control code to always return the rate
even if we should have warned about it. Since this should
not have happened anymore anyway this fix isn't critical
as the proper rate would have been returned anyway.
Cc: stable@kernel.org
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k uses this for now, ath9k_htc is expected to re-use this
as well. We lave ath5k as is, but it certainly can also be
converted later.
The ath9k module parameter and debugfs entry is kept.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DPRINTF() is used in hw specific related code, as such
ensure we don't rely on the private driver core ath_softc
struct when calling it. Drivers can then implement their
own DPRINTF() as they see fit.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Monotonicity of packet error rate should be kept when moving
from one phy to another (legacy to ht, ht single stream to dual,
etc). Current code skips updating per for other phys.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now the lowest rate in 11na ht40 mode is 13.5Mbps this shortens the
range when compared to 11na ht20 mode where the lowest rate is 6.5Mbps.
To improve the range, make 6.5Mbps as the lowest rate in 11na ht40 mode,
this improves the range by approximately 2dB. 11ng ht40 does not have
this issue as it also has basic rates (1, 2, 5.5 and 11).
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move its only member (u8 per) to struct ath_rate_priv.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Get rid of rssi reduce interval.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k rate control is based on only PER (packet error rate),
remove unused code which was intented to do rssi based rate
selection.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the cleanup we just use get_rate as a wrapper, skip
the wrapper.
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All current rate control algorithms agree to send management and no-ack
frames at the lowest rate. They also agree to do this when sta
and the private rate control data is NULL. We add a hlper to mac80211
for this and simplify the rate control algorithm code.
Developers wishing to make enhancements to rate control algorithms
are for broadcast/multicast can opt to not use this in their
gate_rate() mac80211 callback.
Cc: Zhu Yi <yi.zhu@intel.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: ipw3945-devel@lists.sourceforge.net
Cc: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We check for this condition early on in our mac80211 get_rate()
callback ath_get_rate(), so remove this check later down the path.
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The purpose is to find the highest rate we can use.
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This saves us 2733 bytes.
text data bss dec hex filename
252265 3628 1584 257477 3edc5 ath9k-has-b-rate.ko
249905 3628 1584 255117 3e48d ath9k.ko
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Siged-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
What this does is get us our next lower rate so call it that,
ath_rc_get_lower_rix().
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is just calling another helper, so just use the other
helper directly. This should make it clear that when do not
find the next rate we stick to the current one.
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not used, remove this.
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not used, and when we need to get the lowest rate
we should simply use mac80211's own rate_lowest_index(sband, sta).
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has no functional change and just cleans up the code
to be more legible and removes a useless variable for
Multi Rate Retry.
For regular frames we use 2 retries for MRR segments [0-2].
For the last MRR segment [3] we use 4.
MRR[0] = 2
MRR[1] = 2
MRR[2] = 2
MRR[3] = 4
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The case where no vaid rate is found should not happen now
but to help debugging and downgrade this to a warn.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On x86 this allows us to do the following small savings:
shave off 23 % off of the module's data, and
shave off 6 % off of the module's text.
We save 456 bytes, for those counting.
$ size ath9k.ko
text data bss dec hex filename
250794 3628 1600 256022 3e816 ath9k.ko
$ size ath9k-old.ko
text data bss dec hex filename
239114 15308 1600 256022 3e816 ath9k-old.ko
$ du -b ath9k.ko
4034244 ath9k.ko
$ du -b ath9k-old.ko
4033788 ath9k-old.ko
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check for IEEE80211_TX_CTL_NO_ACK instead of is_multicast_ether_addr
when determining whether to use lowest rate without retries.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Senthil Balasubramanian