The current calculation for the video start delay in the current DSI driver
is that it is the total vertical size, minus the front porch and sync length,
plus 1. This equals to the active vertical size plus the back porch plus 1.
That 1 is coming in the Allwinner BSP from an variable that is set to 1.
However, if we look at the Allwinner BSP more closely, and especially in
the "legacy" code for the display (in drivers/video/sunxi/legacy/), we can
see that this variable is actually computed from the porches and the sync
minus 10, clamped between 8 and 100.
This fixes the start delay symptom we've seen on some panels (vblank
timeouts with vertical white stripes at the bottom of the panel).
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6e5f72e68f47ca0223877464bf12f0c3f3978de8.1549896081.git-series.maxime.ripard@bootlin.com
The current code allows the TCON clock divider to have a range between 4
and 127 when feeding the DSI controller.
The only display supported so far had a display clock rate that ended up
using a divider of 4, but testing with other displays show that only 4
seems to be functional.
This also aligns with what Allwinner is doing in their BSP, so let's just
hardcode that we want a divider of 4 when using the DSI output.
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/074e88ae472f5e0492e26939c74b44fb4125ffbd.1549896081.git-series.maxime.ripard@bootlin.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlxqHJYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGWl8H/jPI4EipzD2GbnjZ
GaFpMBBjcXBaVmoA+Y69so+7BHx1Ql+5GQtqbK0RHJRb9qEPLw3FBhHNjM/N8Sgf
nSrK+GnBZp9s+k/NR/Yf2RacUR3jhz+Q9JEoQd3u9bFUeQyvE8Rf3vgtoBBwFOfz
+t7N1memYVF3asLGWB4e4sP1YVMGfseTQpSPojvM30YWM86Bv+QtSx1AGgHczQIM
kMKealR8ZPelN6JAXgLhQ5opDojBrE4YKB98pwsMDI6abz0Tz2JLFEUTTxsv5XNN
o/Iz+XDoylskEyxN2unNWfHx7Swkvoklog8J/hDg5XlTvipL/WkT66PHBgcGMNvj
BW9GgU8=
=ZizU
-----END PGP SIGNATURE-----
Merge v5.0-rc7 into drm-next
Backmerging for nouveau and imx that needed some fixes for next pulls.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Since the DPHY rework, one error path doesn't set the return error code
before jumping to its error label, which in turns make gcc (rightfully)
complain about the variable holding the error code being uninitialized.
Fix this.
Fixes: bb3b6fcb68 ("sun6i: dsi: Convert to generic phy handling")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190208090540.19626-1-maxime.ripard@bootlin.com
When initializing clocks, a reference to the TCON channel 0 clock is
obtained. However, the clock is never prepared and enabled later.
Switching from simplefb to DRM actually disables the clock (that was
usually configured by U-Boot) because of that.
On the V3s, this results in a hang when writing to some mixer registers
when switching over to DRM from simplefb.
Fix this by preparing and enabling the clock when initializing other
clocks. Waiting for sun4i_tcon_channel_enable to enable the clock is
apparently too late and results in the same mixer register access hang.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190131132550.26355-1-paul.kocialkowski@bootlin.com
The A23's display pipeline is similar to the A33. Differences include:
- Display backend supports larger layers, 8192x8192 instead of 2048x2048
- TCON has DMA input
- There is no SAT module packed in the display backend
Add support for the display pipeline and its components.
As the MIPI DSI output device is not officially documented, and there
are no A23 reference devices to test it, it is not covered by this
patch.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190125032314.20915-7-wens@csie.org
In some cases, such as running a new kernel with an old device tree that
has the frontend disabled, the backend's matching frontend might be
unavailable.
When this happens, the layers should only declare support for formats
that the backend support. This partially reverts commit 1c29d263f6
("drm/sun4i: Rename sun4i_backend_layer_formats to sun4i_layer_formats")
by bringing back sun4i_backend_layer_formats, and passing it to
drm_universal_plane_init, while also dropping the modifiers list,
in the event no frontend is available.
Fixes: b636d3f97d ("drm/sun4i: frontend: Add support for the BGRX8888 input format")
Fixes: 9afe52d54b ("drm/sun4i: frontend: Add support for semi-planar YUV input formats")
Fixes: 8c8152bf4d ("drm/sun4i: frontend: Add support for planar YUV input formats")
Fixes: b2ddf277ab ("drm/sun4i: layer: Add tiled modifier support and helper")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190125032314.20915-6-wens@csie.org
We might want to use the backend pointer from DRM callbacks that get
called within drm_universal_plane_init(), such as the
.format_mod_supported callback.
Move the assignment of the layer's backend pointer to right after the
structure is allocated.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190125032314.20915-5-wens@csie.org
The display backend does not support BGRX8888. There is also no trace
of this in the original list of supported formats before the commit
b636d3f97d ("drm/sun4i: frontend: Add support for the BGRX8888 input
format"). Nor do the backend configuration helpers handle this format.
Remove BGRX8888 from list of supported formats by the backend.
Fixes: 3d4265f89d ("drm/sun4i: backend: Add a helper and a list for supported formats")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190125032314.20915-4-wens@csie.org
Having the probe helper stuff (which pretty much everyone needs) in
the drm_crtc_helper.h file (which atomic drivers should never need) is
confusing. Split them out.
To make sure I actually achieved the goal here I went through all
drivers. And indeed, all atomic drivers are now free of
drm_crtc_helper.h includes.
v2: Make it compile. There was so much compile fail on arm drivers
that I figured I'll better not include any of the acks on v1.
v3: Massive rebase because i915 has lost a lot of drmP.h includes, but
not all: Through drm_crtc_helper.h > drm_modeset_helper.h -> drmP.h
there was still one, which this patch largely removes. Which means
rolling out lots more includes all over.
This will also conflict with ongoing drmP.h cleanup by others I
expect.
v3: Rebase on top of atomic bochs.
v4: Review from Laurent for bridge/rcar/omap/shmob/core bits:
- (re)move some of the added includes, use the better include files in
other places (all suggested from Laurent adopted unchanged).
- sort alphabetically
v5: Actually try to sort them, and while at it, sort all the ones I
touch.
v6: Rebase onto i915 changes.
v7: Rebase once more.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Acked-by: CK Hu <ck.hu@mediatek.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: virtualization@lists.linux-foundation.org
Cc: etnaviv@lists.freedesktop.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: spice-devel@lists.freedesktop.org
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-tegra@vger.kernel.org
Cc: xen-devel@lists.xen.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190117210334.13234-1-daniel.vetter@ffwll.ch
Although TMDS clock is required for HDMI to properly function,
nobody called clk_prepare_enable(). This fixes reference counting
issues and makes sure clock is running when it needs to be running.
Due to TDMS clock being parent clock for DDC clock, TDMS clock
was turned on/off for each EDID probe, causing spurious failures
for certain HDMI/DVI screens.
Fixes: 9c5681011a ("drm/sun4i: Add HDMI support")
Signed-off-by: Priit Laes <priit.laes@paf.com>
[Maxime: Moved the TMDS clock enable earlier]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190122073232.7240-1-plaes@plaes.org
This adds the appropriate device-tree compatible for hooking frontend
support for the A20. Since the hardware is very similar to the A10, it
shares the same quirks (which were already introduced).
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-24-paul.kocialkowski@bootlin.com
This adds the appropriate device-tree compatible and quirk data for
hooking frontend support for the A20. It supports the FIR coefficients
ready bit but not the access control bit. It also takes different phase
values than the A33 for these coefficients.
The compatible is already used in the A10 device-tree and already
documented in the device-tree bindings.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-23-paul.kocialkowski@bootlin.com
The COEF_RDY bit is used to tell the hardware that new FIR filters
coefficients have been written to the registers and that the hardware
should take them into account starting next frame.
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-20-paul.kocialkowski@bootlin.com
The ACCESS_CTRL bit is not found on all the variants of the frontend, so
let's introduce a structure that will hold whether or not we need to set
it, and associate it with the compatible.
This will be extended for further similar quirks later on.
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-19-paul.kocialkowski@bootlin.com
Unlike what is currently being done, the ACCESS_CTRL bit documentation asks
that this bit should be set before modifying any register. The code in the
BSP also does this, so make sure we do this as well.
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-18-paul.kocialkowski@bootlin.com
This introduces a list of supported modifiers for the driver, that
includes the Allwinner tiled modifier, as well as a format_mod_supported
callback.
The callback uses both the backend and frontend helpers to indicate
per-format modifier support (including for the linear modifier).
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-16-paul.kocialkowski@bootlin.com
This introduces a helper to check whether a frontend input format
supports tiling mode. This helper is used when tiling is requested in
the frontend format support helper.
Only semiplanar and planar YUV formats are supported by the hardware.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-15-paul.kocialkowski@bootlin.com
This introduces stride and offset configuration for the VPU tiling mode.
Stride is calculated differently than it is for linear formats and an
offset is calculated, for which new register definitions are introduced.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-14-paul.kocialkowski@bootlin.com
This introduces the data input mode definitions for the tiled YUV mode,
that are used in the input mode helper if tiling is requested.
The modifier is passed to the helper from the framebuffer to determine
if tiling is requested.
Only semiplanar and planar YUV formats are supported for tiling mode.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-13-paul.kocialkowski@bootlin.com
Planar YUV formats come with 3 distinct planes, which requires
configuring the frontend line stride and address registers for the
third plane.
Our hardware only supports the YUV planes order and in order to support
formats with a YVU plane order, a helper is introduced to indicate
whether to invert the address of the two chroma planes.
Missing definitions for YUV411 and YUV444 input format configuration are
also introduced as support is added for these formats. For the input
sequence part, no configuration is required for planar YUV formats so
zero is returned in that case.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-11-paul.kocialkowski@bootlin.com
Semi-planar YUV formats use two distinct planes, one for luminance and
one for chrominance. To add support for them, we need to configure the
second line stride and buffer address registers to setup the second YUV
plane.
New definitions are introduced to configure the input format register
for the YUV420 and YUV422 semi-planar formats.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-10-paul.kocialkowski@bootlin.com
This introduces support for packed YUV formats with 4:2:2 sampling using
the frontend. Definitions are introduced for the data format and pixel
sequence input format register values.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-9-paul.kocialkowski@bootlin.com
In prevision of adding support for YUV formats, set the YUV to RGB
colorspace conversion coefficients if required and don't bypass the
CSC engine when converting.
The BT601 coefficients from the A33 BSP are copied over from the backend
code. Because of module inter-dependency, we can't have the frontend use
these coefficients from the backend directly.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-8-paul.kocialkowski@bootlin.com
Both the backend and the frontend need the BT.601 CSC coefficients for
YUV to RGB conversion. Since the backend has a dependency on the
frontend (and not the other way round), move the coefficients there
so that both can access them without having to duplicate them.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-7-paul.kocialkowski@bootlin.com
Since all the RGB input formats have the same value for the DATA_FMT
field of the INPUT_FMT register, we can group them when the format is
known to be RGB. Here, we assume that a non-YUV format is RGB, because
the hardware does not support any other colorspace than RGB and YUV.
Use the DRM format info structure to check whether the format uses a
YUV colorspace.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-6-paul.kocialkowski@bootlin.com
The helper returning the input mode needs to know the number of planes
for the provided format. Passing the fourcc requires iterating through
the format info list in order to return the number of planes.
Pass the DRM format info structure directly instead to all helpers
related to configuring the input format, since it's available to the
caller. Also rename the input format in the caller function to keep
things consistent.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-5-paul.kocialkowski@bootlin.com
Checking for the number of planes is not sufficient to en ensure that
the format is a packed YUV422.
Use explicit fourcc helpers for the check instead.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118145133.21281-4-paul.kocialkowski@bootlin.com
The device node iterators perform an of_node_get on each
iteration, so a jump out of the loop requires an of_node_put.
Remote and port also have augmented reference counts, so drop them
on each iteration and at the end of the function, respectively.
Remote is only used for the address it contains, not for the
contents of that address, so the reference count can be dropped
immediately.
The semantic patch that fixes the first part of this problem is
as follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
iterator name for_each_child_of_node;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
+ of_node_put(child);
? break;
...
}
... when != child
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1547369264-24831-5-git-send-email-Julia.Lawall@lip6.fr
Make life easier for drivers by simply passing the connector
to drm_hdmi_avi_infoframe_from_display_mode() and
drm_hdmi_avi_infoframe_quant_range(). That way drivers don't
need to worry about is_hdmi2_sink mess.
v2: Make is_hdmi2_sink() return true for sil-sii8620
Adapt to omap/vc4 changes
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108172828.15184-1-ville.syrjala@linux.intel.com
To prepare the introduction of tiled mode support, pass the framebuffer
format modifier to the helpers dealing with format support.
Since only linear mode is supported for now, add corresponding checks in
each helper.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-33-paul.kocialkowski@bootlin.com
Our hardware requires the pitch to be an even number when using YUV
formats with the frontend. Implement a driver-specific callback for GEM
dumb allocation that sets the pitch accordingly.
Since only the bpp is passed (and not the format), we cannot really
distinguish if this alignment is really required. Since it doesn't hurt
to align the pitch anyway, always do it.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-30-paul.kocialkowski@bootlin.com
The frontend comes with two "channels", that can be configured
independently. When used in YUV mode, the first channel (CH0) represents
the luminance component while the second channel (CH1) represents the
chrominance. In RGB mode, both have to be configured the same way.
Use variables (with the YUV terminology) for each channel's
dimensions, calculating the chroma dimensions from the luma dimensions
and the sub-sampling factors from the format description.
Since the configured size only has pixel precision, the fractional
fixed-point part of the source size is dropped for both components to
ensure that the scaling factors are accurate.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-26-paul.kocialkowski@bootlin.com
The values in the BT601 YUV to RGB colorspace translation are not
simply coded as multiples, but rather as fixed-point signed fractional
values on a given number of bits. Add an explanation about that.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-24-paul.kocialkowski@bootlin.com
This introduces support for the BGRX8888 input format for the frontend,
with its associated pixel sequence value definition. Other fields are
already configured correctly as they no longer depend on the format's
fourcc directly.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-22-paul.kocialkowski@bootlin.com
Use the number of planes associated with the DRM format to determine the
input mode configuration instead of the format iteself. This way, the
helper can be used for all packed formats without future changes.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-20-paul.kocialkowski@bootlin.com
This introduces proper definitions for the input and output format
configuration registers instead of a macro and raw values in the code,
with the intent to increase code readability and reduce indirections.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-19-paul.kocialkowski@bootlin.com
This introduces new helpers for retrieving the input data mode and pixel
sequence register field values based on the DRM format instead of
hardcoding these. This makes it easier to add support for more formats.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-18-paul.kocialkowski@bootlin.com
In order to support YUV to RGB conversion with the frontend (which is
generally used for connecting with the backend), the CSC block must not
be bypassed.
As a result, the bit to enable CSC bypass is moved from the runtime
resume routine to the format update routine, so that it can disabled
when introducing support for YUV formats later.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-17-paul.kocialkowski@bootlin.com
Since more formats can be supported by the frontend, rename the
variable listing the layer formats to avoid suggesting that the backend
itself supports all the listed formats.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-16-paul.kocialkowski@bootlin.com
Our hardware has a limited number of YUV planes (usually 1) that can be
supported using the backend only. However, YUV planes can also be
supported by the frontend and must then not be counted when checking for
that limitation.
Only count the YUV plane when the frontend is not used.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-15-paul.kocialkowski@bootlin.com
Before this patch, it is assumed that a plane is supported either
through the frontend or through the backend alone. However, the DRM
interface does not allow finely reporting our hardware capabilities
and there are cases where neither are support.
In particular, some plane formats are supported by the backend and not
the frontend, so they can only be supported without scaling.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-8-paul.kocialkowski@bootlin.com
Checking that scaling is in use is not sufficient as a condition to
decide to use the frontend.
Since not all layer formats are supported by the frontend, we need to
check for that support first. Then, the frontend must only be enabled
if the backend doesn't support the format or that scaling is required.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-7-paul.kocialkowski@bootlin.com
In order to check whether the frontend supports a specific format, an
explicit list and a related helper are introduced.
Just like in the backend, the prototype of the helper is added to the
frontend header so that it can be used later on. The helper is also
exported because it will be used outside of the frontend module.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-6-paul.kocialkowski@bootlin.com
In order to check whether the backend supports a specific format, an
explicit list and a related helper are introduced.
The prototype of this helper is added to the header so that it can be
called from sun4i_layer later (when introducing tiled mode support).
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-5-paul.kocialkowski@bootlin.com
The backend allows integer-only scaling but can handle alpha components,
unlike the frontend. It could be useful to add support for this
eventually, so add a short TODO comment describing the situation.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-4-paul.kocialkowski@bootlin.com
The frontend documentation (for the A33) mentions that ARGB is supported
as output, but with the alpha component always set to 0xff. In practice,
this means that the alpha component cannot be preserved when going
through the frontend. Since the information is lost, ARGB is not
properly supported.
As a result, expose the matching format supported by the frontend (both
for input and output) as XRGB instead of ARGB.
Since ARGB was the selected format for connecting the frontend to the
backend, change it to XRGB to reflect this as well.
The A31 and A80 SoCs apparently have a bit to enable proper alpha,
but this is not supported at this point (see the comment already in the
code).
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-3-paul.kocialkowski@bootlin.com
This adds a dedicated function for cleaning the video and YUV source
channel layer enable bits. This function is called first on layer atomic
update to make sure that there are no leftover bits from previous
plane configuration that were not cleaned until now.
It fixes issues when alternating between video and YUV planes, where
both bits would be set eventually, leading to broken plane display.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-2-paul.kocialkowski@bootlin.com
Render like lima will attach a fence to the framebuffer
dma_buf, display like sun4i should wait it finish before
show the framebuffer. Otherwise tearing will be observed.
Signed-off-by: Qiang Yu <yuq825@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181122014417.23285-1-yuq825@gmail.com
drm-next is forwarded to v4.20-rc1, and we need this to make
a patch series apply.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Some panels need an active-low data enable (DE) signal for the RGB
interface. This requires flipping a bit in the TCON0 polarity register
when setting up the mode for the RGB interface.
Match the associated bus flag and use it to set the polarity inversion
bit for the DE signal when required.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107181843.27628-4-contact@paulk.fr
Features such as dithering and pixel data edge configuration currently
rely on the panel registered with the TCON driver. However, bridges are
also supported in addition to panels for RGB setup.
Instead of retrieving the connector from the panel, get it from the
encoder with the dedicated helper.
Even in the case of bridges, the connector is registered with the
encoder from our driver and is accessible when iterating connectors.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107181843.27628-3-contact@paulk.fr
Passing the encoder to the TCON RGB setup functions allows accessing the
connector from the encoder directly instead of relying on the panel.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107181843.27628-2-contact@paulk.fr
Some SoCs, such as H6, doesn't have a full-featured TCON TOP.
Add quirks support for TCON TOP.
Currently the presence of TCON_TV1 and DSI is controlled via the quirks
structure.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[Fixed code style and removed unnecessary initialization]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-25-jernej.skrabec@siol.net
It turns out that TCON TOP registers in H6 SoC have non-zero reset
value. This may cause issues if bits are not changed during
configuration.
To prevent that, initialize registers to 0.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-24-jernej.skrabec@siol.net
H6 has Synopsys DWC HDMI 2.0 TX PHY.
There is no freely available documentation for it, only code found in
BSP kernel. However, judging by the code, PHY is very similar to older
Synopsys HDMI PHY described in i.MX6 documentation. Most registers seem
to be the same.
According to i.MX6 documentation, mpll settings are based on pixel clock
and are not specific to each SoC. Because of that, mpll table in this
commit is based on that documentation and not on BSP code. Other PHY
settings were derived from BSP PHY driver code.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-23-jernej.skrabec@siol.net
Currently sun8i-hdmi-phy driver supports only custom PHYs connected to
DW HDMI controller. Since newest Allwinner SoCs have unmodified Synopsys
PHY, driver has to be reorganized to support them.
Variant structure is expanded to allow differentiation between custom
and Sysnopsys PHYs and to hold Synopsys PHY settings.
Since DW HDMI bridge platform data has different fields for custom and
Sysnopsys PHY, function sun8i_hdmi_phy_get_ops() is replaced with
sun8i_hdmi_phy_set_ops().
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-22-jernej.skrabec@siol.net
Currently, quirks and compatibles are sorted alphabetically. However,
they should be sorted by family release date and then alphabetically.
Fix that by moving A64 quirks and compatible to bottom. No functional
change is made.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-21-jernej.skrabec@siol.net
It turns out that H6 HDMI BSP kernel driver doesn't change TMDS rate at
all. At this point it is not clear whether it is just not necessary or
it would cause some kind of issues.
Add a quirk for it.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-18-jernej.skrabec@siol.net
Since it is not possible to access sun8i-dw-hdmi driver private data
inside mode_valid function, make it configurable. That way different
versions of HDMI controllers can set different function, depending on
it's limitations.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-17-jernej.skrabec@siol.net
Currently supported Allwinner SoCs with DW HDMI controller have
scrambled addresses and read lock. However, that is not true in general.
For example, A80 and H6 have normal addresses and normal read access.
Move code for unscrambling addresses and unlocking read access to it's
own function and call it from init function.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-16-jernej.skrabec@siol.net
Mixer 0 has 1 VI and 3 UI planes, scaler on all planes and can output
4K image @60Hz. It also support 10 bit colors, which are not yet
implemented.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-14-jernej.skrabec@siol.net
Display Engine 3 is an upgrade of DE2 with new features like support for
10 bit color formats and support for AFBC.
Most of DE2 code works with DE3, except some small details.
Implement basic support for DE3. Support for 10 bit colort formats and
AFBC, among others missing features, will be added later.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/260238/
Most, if not all, registers found in DE2 still exists in DE3. However,
units are on different base addresses.
To prepare for addition of DE3 support, registers macros are reworked so
they take base address as parameter.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[rebased]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-10-jernej.skrabec@siol.net
The CMA helper is already using the drm_fb_helper_generic_probe part of
the generic fbdev emulation. This patch makes full use of the generic
fbdev emulation by using its drm_client callbacks. This means that
drm_mode_config_funcs->output_poll_changed and drm_driver->lastclose are
now handled by the emulation code. Additionally fbdev unregister happens
automatically on drm_dev_unregister().
The drm_fbdev_generic_setup() call is put after drm_dev_register() in the
driver. This is done to highlight the fact that fbdev emulation is an
internal client that makes use of the driver, it is not part of the
driver as such. If fbdev setup fails, an error is printed, but the driver
succeeds probing.
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025201340.34227-8-noralf@tronnes.org
The is_double flag is a boolean currently assigned to the value of the d
variable, that is either 1 or 2. It means that this is_double variable is
always set to true, even though the initial intent was to have it set to
true when d is 2.
Fix this.
Fixes: 9c5681011a ("drm/sun4i: Add HDMI support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181021163446.29135-2-maxime.ripard@bootlin.com
The is_double variable is used to store, and possibly returning to the
calling function, whether it needs to double the rate of the parent clock
or not.
In the case where it does, the variable is affected, but in the case where
it doesn't we return some uninitialized value. Fix this.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181021163446.29135-1-maxime.ripard@bootlin.com
-----BEGIN PGP SIGNATURE-----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=3yxi
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2018-10-24' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This is going to rebuild more than drm as it adds a new helper to
list.h for doing bulk updates. Seemed like a reasonable addition to
me.
Otherwise the usual merge window stuff lots of i915 and amdgpu, not so
much nouveau, and piles of everything else.
Core:
- Adds a new list.h helper for doing bulk list updates for TTM.
- Don't leak fb address in smem_start to userspace (comes with EXPORT
workaround for people using mali out of tree hacks)
- udmabuf device to turn memfd regions into dma-buf
- Per-plane blend mode property
- ref/unref replacements with get/put
- fbdev conflicting framebuffers code cleaned up
- host-endian format variants
- panel orientation quirk for Acer One 10
bridge:
- TI SN65DSI86 chip support
vkms:
- GEM support.
- Cursor support
amdgpu:
- Merge amdkfd and amdgpu into one module
- CEC over DP AUX support
- Picasso APU support + VCN dynamic powergating
- Raven2 APU support
- Vega20 enablement + kfd support
- ACP powergating improvements
- ABGR/XBGR display support
- VCN jpeg support
- xGMI support
- DC i2c/aux cleanup
- Ycbcr 4:2:0 support
- GPUVM improvements
- Powerplay and powerplay endian fixes
- Display underflow fixes
vmwgfx:
- Move vmwgfx specific TTM code to vmwgfx
- Split out vmwgfx buffer/resource validation code
- Atomic operation rework
bochs:
- use more helpers
- format/byteorder improvements
qxl:
- use more helpers
i915:
- GGTT coherency getparam
- Turn off resource streamer API
- More Icelake enablement + DMC firmware
- Full PPGTT for Ivybridge, Haswell and Valleyview
- DDB distribution based on resolution
- Limited range DP display support
nouveau:
- CEC over DP AUX support
- Initial HDMI 2.0 support
virtio-gpu:
- vmap support for PRIME objects
tegra:
- Initial Tegra194 support
- DMA/IOMMU integration fixes
msm:
- a6xx perf improvements + clock prefix
- GPU preemption optimisations
- a6xx devfreq support
- cursor support
rockchip:
- PX30 support
- rgb output interface support
mediatek:
- HDMI output support on mt2701 and mt7623
rcar-du:
- Interlaced modes on Gen3
- LVDS on R8A77980
- D3 and E3 SoC support
hisilicon:
- misc fixes
mxsfb:
- runtime pm support
sun4i:
- R40 TCON support
- Allwinner A64 support
- R40 HDMI support
omapdrm:
- Driver rework changing display pipeline ordering to use common code
- DMM memory barrier and irq fixes
- Errata workarounds
exynos:
- out-bridge support for LVDS bridge driver
- Samsung 16x16 tiled format support
- Plane alpha and pixel blend mode support
tilcdc:
- suspend/resume update
mali-dp:
- misc updates"
* tag 'drm-next-2018-10-24' of git://anongit.freedesktop.org/drm/drm: (1382 commits)
firmware/dmc/icl: Add missing MODULE_FIRMWARE() for Icelake.
drm/i915/icl: Fix signal_levels
drm/i915/icl: Fix DDI/TC port clk_off bits
drm/i915/icl: create function to identify combophy port
drm/i915/gen9+: Fix initial readout for Y tiled framebuffers
drm/i915: Large page offsets for pread/pwrite
drm/i915/selftests: Disable shrinker across mmap-exhaustion
drm/i915/dp: Link train Fallback on eDP only if fallback link BW can fit panel's native mode
drm/i915: Fix intel_dp_mst_best_encoder()
drm/i915: Skip vcpi allocation for MSTB ports that are gone
drm/i915: Don't unset intel_connector->mst_port
drm/i915: Only reset seqno if actually idle
drm/i915: Use the correct crtc when sanitizing plane mapping
drm/i915: Restore vblank interrupts earlier
drm/i915: Check fb stride against plane max stride
drm/amdgpu/vcn:Fix uninitialized symbol error
drm: panel-orientation-quirks: Add quirk for Acer One 10 (S1003)
drm/amd/amdgpu: Fix debugfs error handling
drm/amdgpu: Update gc_9_0 golden settings.
drm/amd/powerplay: update PPtable with DC BTC and Tvr SocLimit fields
...
The calculated ideal rate can easily overflow an unsigned long, thus
making the best div selection buggy as soon as no ideal match is found
before the overflow occurs.
Fixes: 4731a72df2 ("drm/sun4i: request exact rates to our parents")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181018100250.12565-1-boris.brezillon@bootlin.com
If tcon->panel pointer is NULL, trying to dereference from it
(i.e. tcon->panel->connector) will cause a null pointer dereference.
Add tcon->panel null pointer check before calling
sun4i_tcon0_mode_set_dithering().
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Fixes: f11adcecbd ("drm/sun4i: tcon: Add dithering support for
RGB565/RGB666 LCD panels")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181005215951.99003-2-giulio.benetti@micronovasrl.com
Since tcon->panel is a pointer returned by of_drm_find_panel() need to
check if it is not NULL, hence a valid pointer.
IS_ERR() instead checks return error values, not NULL pointers.
Substitute "if (!IS_ERR(tcon->panel))" with "if (tcon->panel)".
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181005215951.99003-1-giulio.benetti@micronovasrl.com
This reverts commit 3510e7a7f9.
During the 4.19 merge window for drm-misc, two patches critical to
supporting the display pipeline on the Allwinner R40 SoC were missed.
They were applied later but missed the merge window deadline. As a
result 4.19-rc1 kernel would crash on the R40 when it couldn't parse
the new device tree structure. We ended up removing support for the
R40 display pipeline for 4.19.
Since the missing patches are already merged for 4.20, we can now
revert the commit that removed support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180921142743.8711-1-wens@csie.org
The A64 HDMI PHY seems to be not able to use the second video PLL as
clock parent in experiments.
Drop the support for the second PLL from A64 HDMI PHY driver.
Fixes: b46e2c9f5f ("drm/sun4i: Add support for A64 HDMI PHY")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180916043409.62374-2-icenowy@aosc.io
Having DRM_SUN4I built-in but DRM_SUN8I_MIXER as a loadable module results in
a link error, as we try to access a symbol from the sun8i_tcon_top.ko module:
ERROR: "sun8i_tcon_top_de_config" [drivers/gpu/drm/sun4i/sun4i-tcon.ko] undefined!
ERROR: "sun8i_tcon_top_set_hdmi_src" [drivers/gpu/drm/sun4i/sun4i-tcon.ko] undefined!
ERROR: "sun8i_tcon_top_of_table" [drivers/gpu/drm/sun4i/sun4i-tcon.ko] undefined!
This solves the problem by adding a silent symbol for the tcon_top module,
building it as a separate module in exactly the cases that we need it,
but in a way that it is reachable by the other modules.
Fixes: cf77d79b4e ("drm/sun4i: tcon: Add another way for matching mixers with tcon")
Fixes: 0305189afb ("drm/sun4i: tcon: Add support for R40 TCON")
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Matt Hart <matthew.hart@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180911113325.11024-1-maxime.ripard@bootlin.com
Two patches from the R40 display pipeline support series weren't applied
with the rest of the series. When they did get applied, the -rc6
deadline for drm-misc-next had past, so they didn't get into 4.19-rc1
with the rest of the series. However, the two patches are crucial in
the parsing of the R40's display pipeline graph in the device tree.
Without them, the driver crashes because it can't follow the odd graph
structure.
This patch removes the R40 compatibles from the sun4i-drm driver,
effectively disabling DRM support for the R40 for one release cycle.
This will prevent the driver from crashing upon probing.
The compatibles should be reinstated for the next release.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180827083950.602-1-wens@csie.org
Signed-off-by: Sean Paul <seanpaul@chromium.org>
The hardware supports dithering on TCON channel 0 which is used for LCD
panels.
Dithering is a method of approximating a color from a mixture of other
colors when the required color isn't available. It reduces color
banding artifacts that can be observed when displaying gradients
(e.g. grayscale gradients). This may occur when the image that needs
to be displayed is 24-bit but the LCD panel is a lower bit depth and
does not perform dithering on its own.
Signed-off-by: Jonathan Liu <net147@gmail.com>
[wens@csie.org: check display_info.bpc first; handle LVDS and MIPI DSI]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180907041948.19913-4-wens@csie.org
Dithering is only supported for TCON channel 0. Throughout the datasheet
all the names associated with these register are prefixed "TCON0",
instead of "TCON". The only exception is the control register
"TCON_FRM_CTL_REG".
Rename the macros to reflect this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180907041948.19913-3-wens@csie.org
sun4i_tcon0_mode_set_cpu() currently accepts struct mipi_dsi_device *
as its second parameter. This is derived from drm_encoder.
The DSI encoder is tied to the CPU interface mode of the TCON as a
special case. In theory, if hardware were available, we could also
support normal CPU interface modes. It is better to pass the generic
encoder instead of the specialized mipi_dsi_device, and handle the
differences inside the function.
Passing the encoder would also enable the function to pass it, or any
other data structures related to it, to other functions expecting it.
One such example would be dithering support that will be added in a
later patch, which looks at properties tied to the connector to
determine whether dithering should be enabled or not.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180907041948.19913-2-wens@csie.org
Some boards have HDMI VCC pin connected to voltage regulator which may
not be turned on by default.
Add support for such boards by adding voltage regulator handling code to
HDMI driver.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[Icenowy: change supply name to "hvcc"]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904044053.15425-11-icenowy@aosc.io
Display Engine(DE2) in Allwinner A64 has two mixers and tcons.
The routing for mixer0 is through tcon0 and connected to
LVDS/RGB/MIPI-DSI controller.
The routing for mixer1 is through tcon1 and connected to HDMI.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904044053.15425-6-icenowy@aosc.io
Mixers in Allwinner have similar capabilities as others SoCs with DE2.
Add support for them.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Icenowy: Add mixer1]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904044053.15425-5-icenowy@aosc.io
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This issue was detected with the help of Coccinelle.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180824010521.GA25451@embeddedor.com
Maxime Ripard