Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch introduces the preliminary support for PMICs X-Powers AXP202
and AXP209. The AXP209 and AXP202 are the PMUs (Power Management Unit)
used by A10, A13 and A20 SoCs and developed by X-Powers, a sister company
of Allwinner.
The core enables support for two subsystems:
- PEK (Power Enable Key)
- Regulators
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we pass syscon device node itself as first parameter to this function
there is no need to parse and find syscon device node. So by allowing
"property" parameter as NULL allow syscon_regmap_lookup_by_phandle to
consider passed argument "np" itself as a syscon device node "syscon_np".
This will help us in avoiding addition of "syscon" property in a device node
which points back to same device node in device tree.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The pm8xxx read/write wrappers are no longer necessary now that
all the sub-device drivers are using the regmap API. Remove it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
During suspend the IRQ should be disabled even if this is not a wakeup
source. This is a proper way of fixing the IRQ handling issue during
resume (IRQ handler fails because I2C bus did not resume yet).
When device is suspended and max14577 interrupt is signaled the irq chip
will try to handle it regardless of wakeup source. Device could be woken
up by different IRQ but still the IRQ handler will try to read the
registers over I2C bus and fail because I2C bus won't be ready yet:
max14577 2-0025: Failed to read IRQ status: -5
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
During suspend the IRQ should be disabled even if this is not a wakeup
source. This is a proper way of fixing the IRQ handling issue during
resume (IRQ handler fails because I2C bus did not resume yet).
When device is suspended and sec-core interrupt is signaled the irq chip
will try to handle it regardless of wakeup source. Device could be woken
up by different IRQ but still the IRQ handler will try to read the
registers over I2C bus and fail because I2C bus won't be ready yet.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The device type was stored in sec_pmic_dev state container twice:
- unsigned long type (initialized from of_device_id or i2c_device_id)
- int device_type (initialized as above or from board files when there
is no DTS)
The 'type' field was never used outside of probe so it can be safely
removed.
Change also the device_type in sec_pmic_dev and sec_platform_data to
unsigned long to avoid any casts.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Make sure that we patch the ACCCTL register as the first thing when the
driver loads, thus configuring I2C fast mode and i2c access for dual access
registers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In certain boards the source for the clk32k clock can be gated. In these
boards the clk32k clock can be provided to the driver and it is going to be
enabled/disabled when it is needed.
If the clk32k clock is not provided the driver will assume that it is always
running.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All boards using twl6040 configures the i2c bus to 400KHz. While twl6040's
defaults to normal mode (100KHz). So far twl6040 has no problem with i2c
communication in this configuration it is safer to select fast i2c mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If for some reason the boot loader enabled the audpwron GPIO we will have
pending IRQs to be handled. This seams to break twl6040 for some reason
leading to non working i2c communication (i2c timeouts). Clearing the INTID
register after we requested the audpwron GPIO (and set it to low) will
ensure that the chip will operate normally in this case as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The supply aliases for the MFD devices were being added using devres but
the device hasn't been added at this point and as such we can't use
devres.
The MFD already has a function that removes devices this patch uses the
non-devres versions of the supply alias functions and adds an unregister
in mfd_remove_devices_fn.
Reported-by: Carlo Caione <carlo@caione.org>
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The valid gpio is GPIO0 ~ GPIO58, so ngpio should be 59.
This patch also renames RDC321X_MAX_GPIO to RDC321X_NUM_GPIO because it
actually means the number of available GPIOs.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The rtc-s5m driver does not support all of S2M and S5M chipsets
supported by main MFD sec-core driver. For such chipsets unsupported by
rtc-s5m, the MFD sec-core driver initialized regmap with default config.
This config in such cases wouldn't work at all.
The main MFD sec-core driver shouldn't initialize regmap for child
drivers which is not used by them and even not valid.
Move the allocation of RTC I2C dummy device and initialization of RTC
regmap from main MFD sec-core driver to the rtc-s5m driver. The rtc-s5m
driver will use proper regmap config for supported devices.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This module has always been GPL licensed. It was just missing the explicit
declaration to avoid tainting the kernel.
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Panther Point PCH GPIO configuration is similar to V5 PCHs.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The isolation control register is required when DCVDD is externally
supplied add this in as a readable register.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
After request_threaded_irq() is called there is a chance that an interrupt
may occur before the 'mc13xxx->lock' is initialized, which will trigger a kernel
oops.
In order to prevent that, move the initialization of 'mc13xxx->lock' prior to
requesting the interrupts.
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On systems with CONFIG_FRAME_WARN=1024, compiler warns the allocation of
an object of struct device on stack. Make the allocation dynamically to
fix the warning. Also change the caller's return type to int so as to
account for error handling.
drivers/mfd/abx500-core.c: In function ‘abx500_dump_all_banks’:
drivers/mfd/abx500-core.c:167:1: warning: the frame size of 1032 bytes
is larger than 1024 bytes [-Wframe-larger-than=]
Signed-off-by: Aurabindo J <mail@aurabindo.in>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds attributes to the Kontron PLD driver to allow
applications to retrieve firmware information.
Additionally the format has been changed to conform with the
representation in other Kontron software.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add missing mfd_remove_devices() call in remove function.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support for
big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation and
moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as most
of the other v7 platforms in the tree. \o/ The work isn't quite complete,
there's some driver fixes still needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
Plus a large set of various smaller updates for different platforms. I'm
probably missing some important one here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6LYI
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull part one of ARM SoC updates from Olof Johansson:
"A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support
for big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation
and moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as
most of the other v7 platforms in the tree. \o/
The work isn't quite complete, there's some driver fixes still
needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
plus a large set of various smaller updates for different platforms.
I'm probably missing some important one here"
* tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (281 commits)
ARM: exynos: don't run exynos4 l2x0 setup on other platforms
ARM: exynos: Fix "allmodconfig" build errors in mcpm and hotplug
ARM: EXYNOS: mcpm rename the power_down_finish
ARM: EXYNOS: Enable mcpm for dual-cluster exynos5800 SoC
ARM: EXYNOS: Enable multi-platform build support
ARM: EXYNOS: Consolidate Kconfig entries
ARM: EXYNOS: Add support for EXYNOS5410 SoC
ARM: EXYNOS: Support secondary CPU boot of Exynos3250
ARM: EXYNOS: Add Exynos3250 SoC ID
ARM: EXYNOS: Add 5800 SoC support
ARM: EXYNOS: initial board support for exynos5260 SoC
clk: exynos5410: register clocks using common clock framework
ARM: debug: qcom: add UART addresses to Kconfig help for APQ8084
ARM: sunxi: allow building without reset controller
Documentation: devicetree: arm: sort enable-method entries
ARM: rockchip: convert smp bringup to CPU_METHOD_OF_DECLARE
clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
ARM: dts: axxia: Add reset controller
power: reset: Add Axxia system reset driver
ARM: axxia: Adding defconfig for AXM55xx
...
Some oscillators can be turned off during off-idle saving few
a little bit power at the cost of the oscillator start up
latency.
If you board can do this, you can now enable it by using the
ti,twl4030-power-idle-osc-off compatible flag.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
With the recommended twl4030 configuration added, we can now add
board specific changes as modifications to the recommended
configuration.
Note that the data is private to this driver, and the data must
always have a NULL resource in the sentinel.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
These settings are based on the "Recommended Sleep Sequences for
the Zoom Platform".
The settings assume most of the regulators are under control of
Linux, and twl4030 only cuts off VDD1 and VDD2 during off-idle as
Linux cannot do it.
For any board specific changes to these, let's patch them in as
changes to the generic data in the follow-up patches. This keeps
the board specific changes small.
Note that this does not consider the twl5030 errata 27 and 28.
That can be added later on after it has been tested. For more
information about errata 27 and 28.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The twl4030 PMIC needs to be configured properly for things like
warm reset and deeper idle states so the PMIC manages the regulators
properly based on the hardware triggers from the SoC. Earlier
we have configured twl4030 using platform data, but we want to
do it for device tree based booting also.
In some cases configuring twl4030 is needed for things to work.
For example, when rebooting an OMAP3530 at 125 MHz, it hangs.
With this patch, TWL4030 will be reset when a warm reset occures,
and OMAP3530 does not hang on reboot.
Let's add device tree support and configure things for warm reset
as the default when compatible = "ti,twl4030-power". More
complicated configurations can be added to the driver based on
other compatible flags.
Note we now also make the pdata const like it should be.
This allows use it for match->data with the device tree
related functions.
Based on earlier patch by Matthias Brugger <matthias.bgg@gmail.com>
and Lesly A M <leslyam@ti.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We have these bits partially defined in two different
places, so let's fix them up and add defines for the
missing bits. These bits are the same for P1_SW_EVENTS,
P2_SW_EVENTS and P3_SW_EVENTS.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Looks like we can still hit the issue of wrong load order of
twl4030 configuration. If we have a sleep configuration loaded,
and do a warm reset, the device can hang while initializing the
wakeup12 sequence. We do have a warning message about wrong order
of twl4030 configuration, but in this case it does not help as
the sleep configuration was loaded during the previous boot and
the state of twl4030 is maintained throughout the warm reset.
Fix the issue by clearing any existing sleep configuration
before we load the warm reset configuration.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are two different variants of the tps658640 with slightly
different feature sets.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJTg2N2AAoJELSic+t+oim9+SgQAJ0Rpzzh2ulBEdoVTwFXUkWB
sQV5fw9H2ktO6OHv997vueNmqrVHCM3XaK1qYTYaatE+iD+Pc1Ouq9oWc1zf8nU8
SwRgCoIiZfHvGWoAvn/8yG9zEAZ/Zlx88Y06D/zW2ZqQb8/f4j6cDXR5RXRk8CRN
jAMRTppaNpHmD6V+ljMQKyyq7VmDcPctOkWQFaDpoP39koMRuVMg2W3gTop8Fmxp
0PQVvvjqnsKjfK4MOSZ2ae+dOz4C9McfaLEnU9izcnANLuVZpZPyMa/APamjlP83
kbFjRLlV3hbUmyG6Eloga/w80khdkjbla9FDcP9I8UdZzluqMQL3TBjVTeJ4i1sI
OL/FfJ8VODNV7qVAnnSh2fTGGSrl2/rbl/mR3WLRKqN+WdcfgNwyo9MNADwSCUP2
RoCDezXTBbriVeY6sqKuReUeb+HBjLJ8i5mRgPkl5PReV8wNWHxOnFLEgxmuqR5R
sYu67llv13pUrHj1aPNupnsMUkaGrzQGCw7P0yWdoPfaIcFkiJtNQi+i2Bj/vUBy
lPMeB31PZx3eSJpBJ2DEM9/u24KhVU/WGoY/rNC4KAQRdIcVZvdJVEqpThMcXzld
Gn8O0VgI7vI5b6swsL3d84f+K8pw2rbCNrINO0bpkOaHOkNM4GZ3Zi/J2zxk14Eh
xm2PlL0ziIGjqJuk+ZQu
=KGD4
-----END PGP SIGNATURE-----
Merge tag 'regulator-tps658640' into ib-from-regulator-3.16
regulator: Support newer revisions of tps658640
There are two different variants of the tps658640 with slightly
different feature sets.
The versatile express changes for 3.16 introduced a number of
build regressions for randconfig kernels by not tracking dependencies
between the components right.
This patch tries to rectify that:
* the mach-vexpress code cannot link without the syscfg driver,
which in turn needs MFD_VEXPRESS_SYSREG
* various drivers call devm_regmap_init_vexpress_config(), which
has to be exported so it can be used by loadable modules
* the configuration bus uses OF DT helper functions that are not
available to platforms disable CONFIG_OF
* The sysreg driver exports GPIOs through gpiolib, which can
be disabled on some platforms.
* The clocksource code cannot be built on platforms that don't
use modern timekeeping but rely on gettimeoffset.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The TPS658640 has a different set of output voltage for most LDO and
the RTC LDO isn't settable. This chip also report 2 different version
ID, as the datasheet doesn't list the possible values the second ID
has simply been named TPS658640v2.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The only platform using the STMPE expander now boots from
device tree using all-dynamic GPIO and IRQ number assignments, so
remove the mechanism to pass this from the device tree entirely.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
BCM590xx utilizes a secondary I2C slave address to access additional
register space. Add support for the secondary address space by
instantiating a dummy I2C device with the appropriate secondary
I2C slave address. Also expose a secondary regmap register space so
that MFD drivers can access this secondary i2c slave address space.
Signed-off-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The last reason for static memory mapping is the HBI (board
identification number) check early in the machine code.
Moving the check to the sysreg driver makes it possible to
completely remove the early mapping and init functions.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
This patch - finally, after over 6 months! :-( - addresses
Samuel's request to split the vexpress-sysreg driver into
smaller portions and define the device in a form of MFD
cells:
* LEDs code has been completely removed and replaced with
"gpio-leds" nodes in the tree (referencing dedicated
GPIO subnodes in sysreg - bindings documentation updated);
this also better fits the reality as some variants of the
motherboard don't have all the LEDs populated
* syscfg bridge code has been extracted into a separate
driver (placed in drivers/misc for no better place)
* all the ID & MISC registers are defined as sysconf
making them available for other drivers should they need
to use them (and also to the user via /sys/kernel/debug/regmap
which can be helpful in platform debugging)
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Define syscon platform data structure that can be used
to define a regmap config name. This is particularly useful
in the regmap debugfs when there is more than one syscon
device registered, to distinguish the register blocks.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Components of the Versatile Express platform (configuration
microcontrollers on motherboard and daughterboards in particular)
talk to each other over a custom configuration bus. They
provide miscellaneous functions (from clock generator control
to energy sensors) which are represented as platform devices
(and Device Tree nodes). The transactions on the bus can
be generated by different "bridges" in the system, some
of which are universal for the whole platform (for the price
of high transfer latencies), others restricted to a subsystem
(but much faster).
Until now drivers for such functions were using custom "func"
API, which is being replaced in this patch by regmap calls.
This required:
* a rework (and move to drivers/bus directory, as suggested
by Samuel and Arnd) of the config bus core, which is much
simpler now and uses device model infrastructure (class)
to keep track of the bridges; non-DT case (soon to be
retired anyway) is simply covered by a special device
registration function
* the new config-bus driver also takes over device population,
so there is no need for special matching table for
of_platform_populate nor "simple-bus" hack in the arm64
model dtsi file (relevant bindings documentation has
been updated); this allows all the vexpress devices
fit into normal device model, making it possible
to remove plenty of early inits and other hacks in
the near future
* adaptation of the syscfg bridge implementation in the
sysreg driver, again making it much simpler; there is
a special case of the "energy" function spanning two
registers, where they should be both defined in the tree
now, but backward compatibility is maintained in the code
* modification of the relevant drivers:
* hwmon - just a straight-forward API change
* power/reset driver - API change
* regulator - API change plus error handling
simplification
* osc clock driver - this one required larger rework
in order to turn in into a standard platform driver
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mike Turquette <mturquette@linaro.org>
The STMPE has VCC and VIO supply lines, and sometimes (as on
Ux500) this comes from a software-controlled regulator. Make
it possible to supply the STMPE with power from these
regulators.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current STMPE I2C probing code does not really match the
compatible strings - it matches node names happening to give
the right device name. Instead, let's introduce some real
compatible matching, more complex, more accurate. Make the
driver depend on OF since all platforms using it are DT-only.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The STMPE driver would just read/modify/write the system control
register on the STMPE1601, meaning it would not properly mask off
the PWM block, which remained active if it was on at boot time.
This makes sure the blocks are always masked off if they were
active on boot, saving some power. Also rename the inconsistenty
named STMPE1601 define for the PWM block activation.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit c42deffd5b.
commit <mmc: rtsx: add support for pre_req and post_req> did use
mutex_unlock() in tasklet, but mutex_unlock() can't be used in
tasklet(atomic context). The driver needs to use mutex to avoid
concurrency, so we can't use tasklet here, the patch need to be
removed.
The spinlock host->lock and pcr->lock may deadlock, one way to solve
the deadlock is remove host->lock in sd_isr_done_transfer(), but if
using workqueue the we can avoid using the spinlock and also avoid
the problem.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds devicetree support for mc13783-codec.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The cpufreq core now supports the cpufreq_for_each_entry macro helper
for iteration over the cpufreq_frequency_table, so use it.
It should have no functional changes.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Explain why there is no need to have a symmetric LED turn-on in resume handler
while calling rtsx_usb_turn_off_led() in suspend handler.
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix two possible race condition generated by misuse of del_timer in
rtsx_usb_bulk_transfer_sglist() and uninitialized timers before mfd_add_devices
in rtsx_usb_probe().
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
I noticed a regression where the omap sys_clkreq signal will never
trigger for omap3 when booted with device tree while it triggers
when booted in legacy mode. This means voltage scaling does not
do anything when booted with device tree.
Turns out the reason is we fail to initialize the SmartReflex
enable bit in twl4030 with the following error:
twl: not initialized
And that happens because we are wrongly tinkering with the twl4030
registers in arch/arm/mach-omap2/omap_twl.c before the driver is
initialized. Looking at the the SmartReflex bit enable code in
omap_twl.c, we need to always set it.
So let's fix the issue by always enabling the twl4030 SmartReflex
bit in the drivers/mfd/twl-core.c probe, and drop the related
code in omap_twl.c.
Note that we still have some twl4030 tinkering left in omap_twl.c
for the twl6030 case, but that's a different patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for MAX77836 chipset to the max14577 extcon driver. The
MAX77836 MUIC has additional interrupts (VIDRM, ADC1K) so IRQ handling
is split up into two functions: max14577_parse_irq() and
max77836_parse_irq().
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add Maxim 77836 support to max14577 driver. The chipsets have same MUIC
component so the extcon, charger and regulators are almost the same. The
MAX77836 however has also PMIC and Fuel Gauge.
The MAX77836 uses three I2C slave addresses and has additional interrupts
(related to PMIC and Fuel Gauge). It has also Interrupt Source register,
just like MAX77686 and MAX77693.
The MAX77836 PMIC's TOPSYS and INTSRC interrupts are reported in the
PMIC block. The PMIC block has different I2C slave address and uses own
regmap so another regmap_irq_chip is needed.
Since we have two regmap_irq_chip, use shared interrupts on MAX77836.
This patch adds additional defines and functions to the max14577 MFD core
driver so the driver will handle both chipsets. Also this patch replaces
"0x1 << N" with BIT(N) in defines for register masks.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch prepares for adding support for MAX77836 device to existing
max14577 driver by adding MAX14577 prefix to defines of interrupts.
This is only a rename-like patch, new code is not added.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch continues the preparation for adding support for MAX77836
device to existing max14577 driver.
Add enum for types of devices supported by this driver. The device type
will be detected by matching of_device_id, or i2c_device_id as a
fallback.
The patch also moves to separate function the code related to displaying
DeviceID register values.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add muic prefix to regmap config to differentiate between another regmap
config for MAX77836 PMIC node. Additionally remove unused
symbols: MAX14577_REG_INVALID and max14577_irq_source.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Nearly all of the registers in tps65090 combine control bits and
status bits. Turn off caching of all registers except the select few
that can be cached.
In order to avoid adding more duplicate #defines, we also move some
register offset definitions to the mfd driver (and resolve
inconsistent names).
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we weren't given an interrupt we shouldn't tell child devices (like
the tps65090 charger) that they have an interrupt. This is needed so
that we can support polling mode in the tps65090 charger driver.
See also (charger: tps65090: Allow charger module to be used when no
irq).
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is more idiomatic to process things relating to the regulator in its
driver. This patch moves both processing of device tree relating to the
regulator and checking if the regulator is external from arizona-core
into the regulator driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch factors out the reading of GPIOs for the Arizona devices
into a helper function.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior.
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V.
- Add GPIO descriptor based slot-gpio card detect API.
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c.
- mmci: Support HW busy detection on ux500.
- omap: Support MMC_ERASE.
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23.
- rtsx: Support pre-req/post-req async.
- sdhci: Add support for Realtek RTS5250 controllers.
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect.
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support.
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6S8w
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.15:
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V
- Add GPIO descriptor based slot-gpio card detect API
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c
- mmci: Support HW busy detection on ux500
- omap: Support MMC_ERASE
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23
- rtsx: Support pre-req/post-req async
- sdhci: Add support for Realtek RTS5250 controllers
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs"
* tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (102 commits)
mmc: sdhci-acpi: Intel SDIO has broken card detect
mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller
mmc: sdhci-msm: Add platform_execute_tuning implementation
mmc: sdhci-msm: Initial support for Qualcomm chipsets
mmc: sdhci-msm: Qualcomm SDHCI binding documentation
sdhci: only reprogram retuning timer when flag is set
mmc: rename ARCH_BCM to ARCH_BCM_MOBILE
mmc: sdhci: Allow for irq being shared
mmc: sdhci-acpi: Add device id 80860F16
mmc: sdhci-acpi: Fix broken card detect for ACPI HID 80860F14
mmc: slot-gpio: Add GPIO descriptor based CD GPIO API
mmc: slot-gpio: Split out CD IRQ request into a separate function
mmc: slot-gpio: Record GPIO descriptors instead of GPIO numbers
Revert "dts: socfpga: Add support for SD/MMC on the SOCFPGA platform"
mmc: sdhci-spear: use generic card detection gpio support
mmc: sdhci-spear: remove support for power gpio
mmc: sdhci-spear: simplify resource handling
mmc: sdhci-spear: fix platform_data usage
mmc: sdhci-spear: fix error handling paths for DT
mmc: sdhci-bcm-kona: fix build errors when built-in
...
A large part of the arm-soc patches are nowadays DT changes, adding support
for new SoCs, boards and devices without changing kernel source. The plan
is still to move the devicetree files out of the kernel tree and reduce
the amount of churn going on here, but we keep finding reasons to delay
doing that.
Changes are really all over the place, with little sticking out particularly.
We have contributions from a total of 116 people in this branch.
Unfortunately, the size of this branch also causes a significant number
of conflicts at the moment, typically when subsystem maintainers merge
patches that change the driver at the same time as the dts files. In
most cases this could be avoided because the dts changes are supposed
to be compatible in both ways, and we are asking everyone to send ARM
dts changes through our tree only.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=zl/N
-----END PGP SIGNATURE-----
Merge tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree changes from Arnd Bergmann:
"A large part of the arm-soc patches are nowadays DT changes, adding
support for new SoCs, boards and devices without changing kernel
source. The plan is still to move the devicetree files out of the
kernel tree and reduce the amount of churn going on here, but we keep
finding reasons to delay doing that.
Changes are really all over the place, with little sticking out
particularly. We have contributions from a total of 116 people in
this branch.
Unfortunately, the size of this branch also causes a significant
number of conflicts at the moment, typically when subsystem
maintainers merge patches that change the driver at the same time as
the dts files. In most cases this could be avoided because the dts
changes are supposed to be compatible in both ways, and we are asking
everyone to send ARM dts changes through our tree only"
* tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (541 commits)
dts: stmmac: Document the clocks property in the stmmac base document
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
ARM: STi: stih41x: Add support for the FSM Serial Flash Controller
ARM: STi: stih416: Add support for the FSM Serial Flash Controller
ARM: tegra: fix Dalmore pinctrl configuration
ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm
ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND
ARM: dts: Build all keystone dt blobs
ARM: dts: keystone: Fix control register range for clktsip
ARM: dts: keystone: Fix domain register range for clkfftc1
ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot
ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap
ARM: dts: bcm21664: Add device tree files.
ARM: DT: bcm21664: Device tree bindings
ARM: efm32: properly namespace i2c location property
ARM: efm32: fix unit address part in USART2 device nodes' names
ARM: mvebu: Enable NAND controller in Armada 385-DB
ARM: mvebu: Add support for NAND controller in Armada 38x SoC
ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs
ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs
...
This release has lots and lots of small cleanups and fixes in the
regulator subsystem, mainly cleaning up some bad patterns that got
duplicated in DT code, but otherwise very little of note outside
of the scope of the relevant drivers:
- Support for configuration of the initial state for gpio regulators
with multi-voltage support.
- Support for calling regulator_set_voltage() on fixed regulators.
- New drivers for Broadcom BCM590xx, Freescale pfuze200, Samsung S2MPA01 &
S2MPS11/4, some PWM controlled regulators found on some ST boards and
TI TPS65218.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJTOVGKAAoJELSic+t+oim9EVMP/ibXoOotc1LWU9ARaZ54ncuu
awetV5dugDOQh0uXSJSpo4e6rLV/eZzzKbY29aHN9h76WjM739tOLz2K9cIukZzr
VGA1j/uNwa9SOEDfkK++Qj08PXa/4I3ht912S5mL/Afyg8+AIL1UhE0kFjiTH/+r
8axbj0d9f3CZVmOGU4XH3lLBtlWGq++T4cx4sraekra8vNlisBf2cwr1S7j8Apqq
K5WsOzlWRFXLxct+UrOrmBLdx1Ln9505wjeL3yrvi2Rnw4TBNDTTWgcSqJ22ecBJ
QTr5kbBHuI1qEAcPX4qTzgS0c3TtLQzYjP4K7BZyR5b5EkqpffaA18VVZfo2JQDM
Fr+AfxPt2GLMrad1KshHvQFvmlkgKcESGn6vwnLOCw3jXsS/LiaPuiJlmDCCkCI8
tL62dUinm9EUpDEhxnwP/BKikVZCpG/q+TVx0TS1Yfj0p4EBPHrtvkuIMWeMbWCi
QLgzdp+iioU5UQ2Fpoblw5z4cQmCryzjOEykEy9Y575SS5/oe7rukVMWt5It4zMV
Atgu597v8oZDK6BVZOVq/JuvY9n34mhCBaH3YYRtmbEWXnAe9VjnfJUquWyCvtoz
T0FsM7TinOoCgjJr6YbOtK6dksRMnS3AkHS9UEP0MO2jrfKpgJy/IzlSyo6fl7bw
OVZc4nMmVX82MxPSJtVj
=mrN5
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This release has lots and lots of small cleanups and fixes in the
regulator subsystem, mainly cleaning up some bad patterns that got
duplicated in DT code, but otherwise very little of note outside of
the scope of the relevant drivers:
- Support for configuration of the initial state for gpio regulators
with multi-voltage support.
- Support for calling regulator_set_voltage() on fixed regulators.
- New drivers for Broadcom BCM590xx, Freescale pfuze200, Samsung
S2MPA01 & S2MPS11/4, some PWM controlled regulators found on some
ST boards and TI TPS65218"
* tag 'regulator-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (154 commits)
regulator: aat2870: Use regulator_map_voltage_ascend
regulator: st-pwm: Convert to get_voltage_sel
regulator: Add new driver for ST's PWM controlled voltage regulators
regulator: bcm590xx: Remove **rdev from struct bcm590xx_reg
regulator: bcm590xx: Make the modalias matches the driver name
regulator: s5m8767: Convert to use regulator_[enable|disable|is_enabled]_regmap
regulator: db8500-prcmu: Set 1.8V as a fixed voltage for vsmps2
regulator: s2mps11: Add missing of_node_put
regulator: s2mps11: Use of_get_child_by_name
Documentation: mfd: s2mps11: Document support for S2MPS14
regulator: s2mps11: Add set_suspend_disable for S2MPS14
regulator: s2mps11: Add support for S2MPS14 regulators
regulator: max8660: Fix brace alignment
regulator: dbx500: use seq_puts() instead of seq_printf()
regulator: dbx500-prcmu: Silence checkpatch warnings
regulator: anatop: Remove checking control_reg in [set|get]_voltage_sel
regulator: max8952: Silence checkpatch warning
regulator: max8925: Silence checkpatch warning
regulator: max8660: Silence checkpatch warnings
regulator: arizona-ldo1: Correct default regulator init_data
...
The DSPs will often control there own clock speeds whilst running as
such we should mark the registers controlling this as volatile.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On PXT and COMe-cPC2 boards it is observed that the hardware
mutex is acquired but not being released during initialization.
This can result in a hang-up during boot if the driver is built
into the kernel.
Releasing the mutex twice if it was acquired fixes the problem.
Subsequent request/release cycles work as expected, so the fix is
only needed during initialization.
Cc: <stable@vger.kernel.org>
Reviewed-by: Michael Brunner <michael.brunner@kontron.com>
Tested-by: Michael Brunner <michael.brunner@kontron.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Initialize the 'regmap_rtc' on S2MPA01 to some sane value. Sane at least
for S5M87X chipsets, not S2MPS/S2MPA but it won't be used because
rtc-s5m driver does not support S2MPA01.
This fixes following error:
drivers/mfd/sec-core.c:342:45: warning: ‘regmap_rtc’ may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The tps65910_i2c_probe() allocates regmap_irq_chip in
tps65910_irq_init() but it does not clean this up in case of
mfd_add_devices() failure.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixes: 4aab3fadad ("mfd: tps65910: Move interrupt implementation code to mfd file")
tps65910_irq_init() sets 'tps65910->chip_irq' before calling
regmap_add_irq_chip(). If the regmap_add_irq_chip() call fails in
memory allocation of regmap_irq_chip_data members then:
1. The 'tps65910->chip_irq' will still hold some value
2. 'tps65910->irq_data' will be pointing to already freed memory
(because regmap_add_irq_chip() will free it on error)
This results in invalid memory access during driver remove because the
tps65910_irq_exit() tests whether 'tps65910->chip_irq' is not zero.
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Dummy I2C device allocated in sec_pmic_probe() leaked if
devm_regmap_init_i2c() failed. Unregister it before returning from
probe.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add of_compatible strings for S5M8767 and S2MPS14 clock MFD cells.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The tnetv107x platform is getting removed, so this driver
is not needed any more.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This fixes below build error.
FATAL: drivers/mfd/bcm590xx: sizeof(struct i2c_device_id)=24 is not a modulo of the size of section __mod_i2c_device_table=392.
Fix definition of struct i2c_device_id in mod_devicetable.h
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds the LPC Controller Device IDs for Watchdog and GPIO for
the Intel Bay Trail Atom SoC.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The NM10's GPIO is compatible with ICH v7 GPIO.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Dan Weinlader <danw@vs-networks.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The register layout of the Avoton is compatible with the iTCO v3
register layout.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Rajat Jain <rajatjain@juniper.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some newer Atom CPUs, eg Avoton and Bay Trail, use slightly different
register layouts for the iTCO than the current v1 and v2 iTCO.
Differences from previous iTCO versions include:
- The ACPI space is enabled in the "ACPI base address" register instead
of the "ACPI control register"
- The "no reboot" functionality is set in the "Power Management
Configuration" register instead of the "General Control and Status"
(GCS) register or PCI configuration space.
- The "ACPI Control Register" is not present on v3. The "Power
Management Configuration Base Address" register resides at the same
address is Avoton/Bay Trail.
To differentiate these newer chipsets create a new v3 iTCO version and
update the MFD driver to support them.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Rajat Jain <rajatjain@juniper.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Future chipsets will use different register layouts that don't map
cleanly to the lpc_ich_cfg fields. Remove the lpc_ich_cfg struct and
add explicit fields to the higher level lpc_ich_priv structure.
This change should have no functional impact.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Rajat Jain <rajatjain@juniper.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some chipsets don't currently have GPIO support enabled. For these
chipsets don't go through the process of initializing the GPIO region.
Make the same change for the watchdog initialization for chipsets which
may not enable the WDT in the future.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Rajat Jain <rajatjain@juniper.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The original bitmask of 0x10 was incorrect and would result in a write
to a reserved read-only bit instead of enabling the ACPI I/O
region. Update it to the proper value of 0x80.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Rajat Jain <rajatjain@juniper.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add a driver for the BCM590xx PMU multi-function devices. The driver
initially supports regmap initialization and instantiation of the
voltage regulator device function of the PMU.
Signed-off-by: Matt Porter <mporter@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
MAXIM 14577 MFD driver uses the regmap_irq_chip so it's Kconfig entry
should select REGMAP_IRQ.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are some unused registers in twl4030 at I2C address 0x49 and function
twl4030_49_nop_reg() is used to check accessibility of that registers. These
registers are written in decimal format but the values are correct in
hexadecimal format. (It can be checked few lines above the patched code -
these registers are marked as unused there.)
As a consequence three registers of audio submodule are treated as
inaccessible (preamplifier carkit right and both handsfree registers).
Cc: stable@vger.kernel.org
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reported error was:
ERROR: "regmap_del_irq_chip" [drivers/mfd/tps65218.ko] undefined!
when CONFIG_REGMAP_IRQ is not enabled.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since we do not want to add new platform IDs for the syscon driver,
there is no reason to iterate over IDs. This patch simplifies
syscon_match_pdevname() function to remove such iteration.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
platform_get_irq() returns a negative error code when an IRQ is invalid
or unspecified. Make 'irq' signed to properly handle this.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The FUSE7_REG register is not currently marked readable. This causes
as3722_sd0_is_low_voltage() to emit an error during boot, and assume
the range of the SD0 regulator:
as3722-regulator as3722-regulator: Reg 0xa7 read failed: -5
Fixes: d4807ad2c4 ("regmap: Check readable regs in _regmap_read")
[exposed the bug, by checking for readability]
Fixes: 762a8ee808 ("regulator: as3722: detect SD0 low-voltage mode")
[left out this register from the readable list]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We don't need to implement a dummy irq_set_wake op if we just set
IRQCHIP_SKIP_SET_WAKE.
Suggested-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This isn't necessary as we aren't setting the summary interrupt
to wake up the system in the irq_wake() callback.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The probe routine should call spi_setup() to configure the SPI bus
so it can properly communicate with the device.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The patch adds the maximum speed limit in accordance with the
PMIC datasheet if other value is not given in the devicetree
description or board data.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use SIMPLE_DEV_PM_OPS macro in order to make the code simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Allow this driver to be compiled on all ARM builds as it doesn't
rely on anything within arm/mach-msm.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Jingoo Han