Use DEVICE_ATTR_RO() macro helper instead of plain DEVICE_ATTR(), which
makes the code a bit shorter and easier to read.
Link: https://lore.kernel.org/r/20210616034419.725-2-thunder.leizhen@huawei.com
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qedi_clear_session_ctx() could race with the in-kernel or userspace driven
recovery/removal and we could access a NULL conn or do a double free.
We should be using iscsi_host_remove() to start the removal process from
the driver. It will start the in-kernel recovery and notify userspace that
the driver's scsi_hosts are being removed. iscsid will then drive the
session removal like is done when the logout command is run. When the
sessions are removed, iscsi_host_remove() will return so qedi can finish
knowing there are no running sessions and no new sessions will be allowed.
This also fixes an issue where we check for a NULL conn after already
accessing it introduced in commit 27e986289e ("scsi: iscsi: Drop suspend
calls from ep_disconnect") by just removing the function completely.
Link: https://lore.kernel.org/r/20210609192709.5094-1-michael.christie@oracle.com
Fixes: 27e986289e ("scsi: iscsi: Drop suspend calls from ep_disconnect")
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If we got a response then we should always wake up the conn. For both the
cmd_cleanup_req == 0 or cmd_cleanup_req > 0, we shouldn't dig into
iscsi_itt_to_task because we don't know what the upper layers are doing.
We can also remove the qedi_clear_task_idx call here because once we signal
success libiscsi will loop over the affected commands and end up calling
the cleanup_task callout which will release it.
Link: https://lore.kernel.org/r/20210525181821.7617-29-michael.christie@oracle.com
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We need to make sure that abort and reset completion work has completed
before ep_disconnect returns. After ep_disconnect we can't manipulate
cmds because libiscsi will call conn_stop and take onwership.
We are trying to make sure abort work and reset completion work has
completed before we do the cmd clean up in ep_disconnect. The problem is
that:
1. the work function sets the QEDI_CONN_FW_CLEANUP bit, so if the work was
still pending we would not see the bit set. We need to do this before
the work is queued.
2. If we had multiple works queued then we could break from the loop in
qedi_ep_disconnect early because when abort work 1 completes it could
clear QEDI_CONN_FW_CLEANUP. qedi_ep_disconnect could then see that
before work 2 has run.
3. A TMF reset completion work could run after ep_disconnect starts
cleaning up cmds via qedi_clearsq. ep_disconnect's call to qedi_clearsq
-> qedi_cleanup_all_io would might think it's done cleaning up cmds,
but the reset completion work could still be running. We then return
from ep_disconnect while still doing cleanup.
This replaces the bit with a counter to track the number of queued TMF
works, and adds a bool to prevent new works from starting from the
completion path once a ep_disconnect starts.
Link: https://lore.kernel.org/r/20210525181821.7617-28-michael.christie@oracle.com
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qedi_abort_work knows what task to abort so just pass it to send_iscsi_tmf.
Link: https://lore.kernel.org/r/20210525181821.7617-27-michael.christie@oracle.com
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Drivers shouldn't be calling block/unblock session for cmd cleanup because
the functions can change the session state from under libiscsi. This adds
a new a driver level bit so it can block all I/O the host while it drains
the card.
Link: https://lore.kernel.org/r/20210525181821.7617-26-michael.christie@oracle.com
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Drivers shouldn't be calling block/unblock session for tmf handling because
the functions can change the session state from under libiscsi.
iscsi_queuecommand's call to iscsi_prep_scsi_cmd_pdu->
iscsi_check_tmf_restrictions will prevent new cmds from being sent to qedi
after we've started handling a TMF. So we don't need to try and block it in
the driver, and we can remove these block calls.
Link: https://lore.kernel.org/r/20210525181821.7617-25-michael.christie@oracle.com
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We run from a workqueue with no locks held so use GFP_NOIO.
Link: https://lore.kernel.org/r/20210525181821.7617-24-michael.christie@oracle.com
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qedi_iscsi_abort_work and qedi_tmf_work both allocate a tid then call
qedi_send_iscsi_tmf which also allocates a tid. This removes the tid
allocation from the callers.
Link: https://lore.kernel.org/r/20210525181821.7617-23-michael.christie@oracle.com
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If qedi_tmf_work's qedi_wait_for_cleanup_request call times out we will
also force the clean up of the qedi_work_map but
qedi_process_cmd_cleanup_resp could still be accessing the qedi_cmd.
To fix this issue we extend where we hold the tmf_work_lock and back_lock
so the qedi_process_cmd_cleanup_resp access is serialized with the cleanup
done in qedi_tmf_work and any completion handling for the iscsi_task.
Link: https://lore.kernel.org/r/20210525181821.7617-22-michael.christie@oracle.com
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the SCSI cmd completes after qedi_tmf_work calls iscsi_itt_to_task then
the qedi qedi_cmd->task_id could be freed and used for another cmd. If we
then call qedi_iscsi_cleanup_task with that task_id we will be cleaning up
the wrong cmd.
Wait to release the task_id until the last put has been done on the
iscsi_task. Because libiscsi grabs a ref to the task when sending the
abort, we know that for the non-abort timeout case that the task_id we are
referencing is for the cmd that was supposed to be aborted.
A latter commit will fix the case where the abort times out while we are
running qedi_tmf_work.
Link: https://lore.kernel.org/r/20210525181821.7617-21-michael.christie@oracle.com
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If qedi_process_cmd_cleanup_resp finds the cmd it frees the work and sets
list_tmf_work to NULL, so qedi_tmf_work should check if list_tmf_work is
non-NULL when it wants to force cleanup.
Link: https://lore.kernel.org/r/20210525181821.7617-20-michael.christie@oracle.com
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The iscsi offload drivers are setting the shost->max_id to the max number
of sessions they support. The problem is that max_id is not the max number
of targets but the highest identifier the targets can have. To use it to
limit the number of targets we need to set it to max sessions - 1, or we
can end up with a session we might not have preallocated resources for.
Link: https://lore.kernel.org/r/20210525181821.7617-15-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Subsequent commits allow the kernel to do ep_disconnect. In that case we
will have to get a proper refcount on the ep so one thread does not delete
it from under another.
Link: https://lore.kernel.org/r/20210525181821.7617-7-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
libiscsi will now suspend the send/tx queue for the drivers so we can drop
it from the drivers ep_disconnect.
Link: https://lore.kernel.org/r/20210525181821.7617-4-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During ep_disconnect we have been doing iscsi_suspend_tx/queue to block new
I/O but every driver except cxgbi and iscsi_tcp can still get I/O from
__iscsi_conn_send_pdu() if we haven't called iscsi_conn_failure() before
ep_disconnect. This could happen if we were terminating the session, and
the logout timed out before it was even sent to libiscsi.
Fix the issue by adding a helper which reverses the bind_conn call that
allows new I/O to be queued. Drivers implementing ep_disconnect can use this
to make sure new I/O is not queued to them when handling the disconnect.
Link: https://lore.kernel.org/r/20210525181821.7617-3-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull 5.12/scsi-fixes into the 5.13 SCSI tree to provide a baseline for
some UFS changes that would otherwise cause conflicts during the
merge.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable err is assigned -ENOMEM followed by an error return path via label
err_udev that does not access the variable and returns with the -ENOMEM
error return code. The assignment to err is redundant and can be removed.
Link: https://lore.kernel.org/r/20210327230650.25803-1-colin.king@canonical.com
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When kzalloc() returns NULL to qedi->global_queues[i], no error return code
of qedi_alloc_global_queues() is assigned. To fix this bug, status is
assigned with -ENOMEM in this case.
Link: https://lore.kernel.org/r/20210308033024.27147-1-baijiaju1990@gmail.com
Fixes: ace7f46ba5 ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The CHAP secret displayed garbage characters causing iSCSI login
authentication failure. Correct the CHAP password max length.
Link: https://lore.kernel.org/r/20201217105144.8055-1-njavali@marvell.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the missing destroy_workqueue() before return from __qedi_probe in the
error handling case when fails to create workqueue qedi->offload_thread.
Link: https://lore.kernel.org/r/20201109091518.55941-1-miaoqinglang@huawei.com
Fixes: ace7f46ba5 ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On fan failure event from MFW, bring down active connections and unload
the firmware context.
Link: https://lore.kernel.org/r/20200924070338.8270-1-mrangankar@marvell.com
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The error recovery is handled by management firmware (MFW) with the help of
qed/qedi drivers. Upon detecting errors, driver informs MFW about this
event which in turn starts a recovery process. MFW sends ERROR_RECOVERY
notification to the driver which performs the required cleanup/recovery
from the driver side.
Link: https://lore.kernel.org/r/20200908095657.26821-9-mrangankar@marvell.com
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support to initiate MFW process recovery for all the devices if storage
function receives the event first.
Also added fix for kernel test robot warning,
>> drivers/scsi/qedi/qedi_main.c:1119:6: warning: no previous prototype
>> for 'qedi_schedule_hw_err_handler' [-Wmissing-prototypes]
Link: https://lore.kernel.org/r/20200908095657.26821-8-mrangankar@marvell.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For short time cable pulls, the in-flight I/O to the firmware is never
cleaned up, resulting in the behaviour of stale I/O completion causing
list_del corruption and soft lockup of the system.
On link down event, mark all the connections for recovery, causing cleanup
of all the in-flight I/O immediately.
Link: https://lore.kernel.org/r/20200908095657.26821-7-mrangankar@marvell.com
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Protect active command list for non-I/O commands like login response,
logout response, text response, and recovery cleanup of active list to
avoid list corruption.
Link: https://lore.kernel.org/r/20200908095657.26821-5-mrangankar@marvell.com
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While aborting the I/O, the firmware cleanup task timed out and driver
deleted the I/O from active command list. Some time later the firmware
sent the cleanup task response and driver again deleted the I/O from
active command list causing firmware to send completion for non-existent
I/O and list_del corruption of active command list.
Add fix to check if I/O is present before deleting it from the active
command list to ensure firmware sends valid I/O completion and protect
against list_del corruption.
Link: https://lore.kernel.org/r/20200908095657.26821-4-mrangankar@marvell.com
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In boot from SAN scenario when qedi PCI shutdown handler is called with
active iSCSI sessions, sometimes target takes too long time to respond to
firmware connection termination request. Instead skip sending termination
ramrod and progress with unload path.
Link: https://lore.kernel.org/r/20200908095657.26821-3-mrangankar@marvell.com
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To avoid unnecessary vector allocation when the number of fast-path queues
is less then available msix vectors, use return count from module
qed->set_fp_int.
Link: https://lore.kernel.org/r/20200908095657.26821-2-mrangankar@marvell.com
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
kfree_skb() handles a NULL skb argument so the additional check is
unnecessary. Remove it.
Link: https://lore.kernel.org/r/20200827092606.32148-1-vulab@iscas.ac.cn
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is the only use of kerneldoc in the source file and no descriptions
are provided.
Fixes the following W=1 kernel build warning(s):
drivers/scsi/qedi/qedi_main.c:1969: warning: Function parameter or member 'qedi' not described in 'qedi_get_nvram_block'
Link: https://lore.kernel.org/r/20200723122446.1329773-37-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@cavium.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/qedi/qedi_fw.c: In function ‘qedi_put_rq_bdq_buf’:
drivers/scsi/qedi/qedi_fw.c:355:6: warning: variable ‘tmp’ set but not used [-Wunused-but-set-variable]
Link: https://lore.kernel.org/r/20200723122446.1329773-32-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@cavium.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/qedi/qedi_main.c: In function ‘qedi_queue_cqe’:
drivers/scsi/qedi/qedi_main.c:1158:21: warning: variable ‘conn’ set but not used [-Wunused-but-set-variable]
1158 | struct iscsi_conn *conn;
| ^~~~
drivers/scsi/qedi/qedi_main.c: In function ‘__qedi_probe’:
drivers/scsi/qedi/qedi_main.c:2432:6: warning: variable ‘tmp’ set but not used [-Wunused-but-set-variable]
2432 | u16 tmp;
| ^~~
Link: https://lore.kernel.org/r/20200723122446.1329773-12-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@cavium.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
uctrl and udev are unused after commit 9632a6b4b7 ("scsi: qedi: Move LL2
producer index processing in BH.")
Remove them.
Link: https://lore.kernel.org/r/20200505121904.25702-1-xiexiuqi@huawei.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Xie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following coccicheck warning:
drivers/scsi/qedi/qedi_main.c:1309:5-25: WARNING: Comparison of 0/1 to
bool variable
drivers/scsi/qedi/qedi_main.c:1315:5-25: WARNING: Comparison of 0/1 to
bool variable
Link: https://lore.kernel.org/r/20200430121706.14879-1-yanaijie@huawei.com
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Smatch complains that the "path_data->handle" variable is user controlled.
It comes from iscsi_set_path() so that seems possible. It's harmless to
add a limit check.
The qedi->ep_tbl[] array has qedi->max_active_conns elements (which is
always ISCSI_MAX_SESS_PER_HBA (4096) elements). The array is allocated in
the qedi_cm_alloc_mem() function.
Link: https://lore.kernel.org/r/20200428131939.GA696531@mwanda
Fixes: ace7f46ba5 ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following sparse warning:
drivers/scsi/qedi/qedi_main.c:44:6: warning: symbol 'qedi_ll2_buf_size' was
not declared. Should it be static?
Link: https://lore.kernel.org/r/20200415085029.7170-1-yanaijie@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The destroy connection ramrod timed out during session logout. Fix the
wait delay for graceful vs abortive termination as per the FW requirements.
Link: https://lore.kernel.org/r/20200408064332.19377-7-mrangankar@marvell.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add module parameter to enable debug messages specific to iSCSI functions.
Link: https://lore.kernel.org/r/20200408064332.19377-6-mrangankar@marvell.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No need to allocate and deallocate endpoint memory if the physical link is
down.
Link: https://lore.kernel.org/r/20200408064332.19377-3-mrangankar@marvell.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While parsing the iSCSI TLV data to MFW request, a newline was added to the
firmware boot target iqnname string. Because of this, we were getting the
following error even after the boot target was successfully logged in:
"[qedi_get_protocol_tlv_data:1197]:1: Boot target not set"
Remove the trailing newline.
[mkp: clarified commit desc]
Link: https://lore.kernel.org/r/20200408064332.19377-2-mrangankar@marvell.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds the mfw error recovery process in the qedi driver. The
process includes a partial/customized driver unload and load to reset
context by preserving active iSCSI session kernel state.
Link: https://lore.kernel.org/r/20200319083811.19499-2-mrangankar@marvell.com
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix misspellings of "disonnect", "reconnect", "connection", "connected",
and "disconnection".
Link: https://lore.kernel.org/r/20191024152633.30404-1-geert+renesas@glider.be
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The new route handling in ip_mc_finish_output() from 'net' overlapped
with the new support for returning congestion notifications from BPF
programs.
In order to handle this I had to take the dev_loopback_xmit() calls
out of the switch statement.
The aquantia driver conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhen Lei