Now races can happen between interrupt handler execution and PM runtime in
error handling code path in probe and in dwc3_omap_remove() which will lead
to system crash:
in probe:
...
err1:
pm_runtime_put_sync(dev);
^^ PM runtime can race with IRQ handler when deferred probing happening
due to extcon
pm_runtime_disable(dev);
return ret;
in dwc3_omap_remove:
...
dwc3_omap_disable_irqs(omap);
^^ IRQs are disabled in HW, but handler may still run
of_platform_depopulate(omap->dev);
pm_runtime_put_sync(&pdev->dev);
^^ PM runtime can race with IRQ handler
pm_runtime_disable(&pdev->dev);
return 0;
So, OMAP DWC3 IRQ need to be disabled before calling
pm_runtime_put() in probe and in dwc3_omap_remove().
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case EP disabled pass only EPCPLT command
to be handled. In other case we could hit
Bug like below.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000003
IP:
[<ffffffff81673428>] dwc3_thread_interrupt+0x11c8/0x1790
while dep->endpoint.desc is NULL.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb_get_dr_mode() expects the device-property to be spelled
"dr_mode" not "dr-mode".
Spelling it properly fixes the following warning showing up in dmesg:
[ 8704.500545] dwc3 dwc3.2.auto: Configuration mismatch. dr_mode forced to gadget
Signed-off-by: Hans de Goede <hdegoede@redhat.com
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we're handling so many transfers at a time
and for some dwc3 revisions LPM events *must* be
enabled, we can fall into a situation where too many
events fire and we start receiving Overflow events.
Let's do what XHCI does and allocate a full page for
the Event Ring, this will avoid any future issues.
Cc: <stable@vger.kernel.org> # v4.9
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
commit 0416e494ce ("usb: dwc3: ep0: correct cache
sync issue in case of ep0_bounced") introduced a bug
where we would leak DMA resources which would cause
us to starve the system of them resulting in failing
DMA transfers.
Fix the bug by making sure that we always unmap EP0
requests since those are *always* mapped.
Fixes: 0416e494ce ("usb: dwc3: ep0: correct cache
sync issue in case of ep0_bounced")
Cc: <stable@vger.kernel.org>
Tested-by: Tomasz Medrek <tomaszx.medrek@intel.com>
Reported-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Let's call dwc3_ep0_prepare_one_trb() explicitly
because there are occasions where we will need more
than one TRB to handle an EP0 transfer.
A follow-up patch will fix one bug related to
multiple-TRB Data Phases when it comes to
mapping/unmapping requests for DMA.
Cc: <stable@vger.kernel.org>
Reported-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For now this is just a cleanup patch, no functional
changes. We will be using the new function to fix a
bug introduced long ago by commit 0416e494ce
("usb: dwc3: ep0: correct cache sync issue in case
of ep0_bounced") and further worsened by commit
c0bd5456a4 ("usb: dwc3: ep0: handle non maxpacket
aligned transfers > 512")
Cc: <stable@vger.kernel.org>
Reported-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
-----BEGIN PGP SIGNATURE-----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=5WN9
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.10 merge window
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
The dma mask is correctly set up by the DT probe function, no
need to override it any more.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dma ops for dwc3 devices are not set properly. So, use a
physical device sysdev, which will be inherited from parent,
to set the hardware / firmware parameters like dma.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Building with W=1, we get a warning about harmless empty statements:
drivers/usb/dwc3/ep0.c: In function 'dwc3_ep0_handle_intf':
drivers/usb/dwc3/ep0.c:491:4: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
Instead of adding empty braces which would introduce checkpatch.pl
warnings, we're just removing the code which doesn't do anything and
making sure we return 0 so USBCV tool is happy.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_pci_dsm() is only needed if (PM || PM_SLEEP),
we should make sure it's not defined if neither of
those is defined.
This fixes a randconfig build warning.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This is a workaround for STAR 9000961433 which affects only version
3.00a of the DWC_usb3 core. This prevents the controller interrupt from
being masked while handling events. Enabling interrupt moderation allows
us to work around this issue because once the GEVNTCOUNT.count is
written the IRQ is immediately deasserted and won't be asserted again
until GEVNTCOUNT.EHB is cleared.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Implement interrupt moderation which allows the interrupt rate to be
throttled. To enable this feature the dwc->imod_interval must be set to
1 or greater. This value specifies the minimum inter-interrupt interval,
in 250 ns increments. A value of 0 disables interrupt moderation.
This applies for DWC_usb3 version 3.00a and higher and for DWC_usb31
version 1.20a and higher.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that all the infrastructure is in place, we can
clear events in the top-half handler in order to
bring IRQ line low ASAP.
This is also a necessary step in order to implement
workaround for known erratum in follow-up patches.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Let's start copying events from evt->buf to
evt->cache and use evt->cache for processing events.
A follow-up patch will be added to clear events in
the top-half handler in order to bring IRQ line low
as soon as possible.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of always accessing the macro directly,
let's rely on evt->length which is the actual length
of current event buffer. While unlikely, we could
change event buffer's size at any time.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This extra buffer will be used so we can copy
triggered events from our event buffer to this cache
and process all of them later in bottom half
handler.
We need this in order to implement a workaround for
a known erratum in recent DWC3 release.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_soft_reset() is doing the same thing as
dwc3_core_soft_reset(). Let's remove
dwc3_soft_reset() since that's not needed anymore.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a function to check properties and call it from probe. This will
allow us to add check code without bloating the probe function. This
needs to be done after dwc3_get_properties() and dwc3_core_init() so
that all the properties and hardware configs are available.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a helper function to check if we are running on a DWC_usb3 core.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The register programming code in dwc2_updated_ram_clk_sel() will never
be executed. And in fact the entire function can be removed as there is
no way to override the default value of GCTL.RAMCLKSEL. Remove the
function and add a comment explaining where GCTL.RAMCLKSEL should be
programmed if needed in the future.
This fixes dead code warnings in coverity.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The __dwc3_gadget_endpoint_enable() function has access to the endpoint
descriptors via the usb_ep. So we don't need to pass them in as
arguments. The descriptors should be set by the caller prior to calling
usb_ep_enable().
Signed-off-by: John Youn <johnyoun@synopsys.com>
[felipe.balbi@linux.intel.com : minor improvements]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Seems last time we hit few issues where
we get trb_left = 0, mainly because of
HWO bit still set in previous TRB.
Add warn on once to catch/fix such
problems much faster.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After we kick_transfer we should clean
DWC3_EP_PENDING_REQUEST endpoint flag.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use pre-increment and set -ETIMEDOUT correctly.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case STARTTRANSFER will fail, clean TRB.
Seems HW in such case don't clean HWO bit.
So, without this cleanup prev_trb still have
HWO bit set.
In my case (without patch), after first START failed:
- dep->enqueue == 1
- dep->dequeue == 1
- prev_trb still have HWO set
- left_trb() == 0
No way to send more data.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case we will fail to STARTTRANSFER we should
also decrement queued_requests.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Finally get rid of dwc3_trace() hack. If any other
message is truly needed, we should add proper
tracepoints for them instead of hacking around with
dwc3_trace() or similar.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of using a simple trace_printk() wrapper,
let's add an actual tracepoint and print further
details about the endpoint being operated upon.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Intel's BXT devices need to execute a _DSM method
during {runtime_,}{suspend,resume} in order to get a
chunk of dwc3 to power gate and save some extra
power.
Let's do that now.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We'll be tracking a little more information for PCI
drivers, it's about time we add a private structure
for that.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When we get a half-way processed request, we should
make sure to try to prepare further TRBs for it or
for any possibly queued up request held in our
pending_list. This will make sure our controller is
kept busy for as long as possible.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Say we have three requests prepared to the HW (reqA,
reqB, and reqC). All of them are composed of
SG-lists with several entries and they all requests
interrupt only on last TRBs of the SG-list.
When we get interrupt for reqA, it could be that
reqB is already half-way transferred and some of its
TRBs will have HWO already cleared.
It's okay to free up TRBs without HWO bit set, but
we need to guarantee we don't giveback a request
that's half-way transferred as that will confuse
gadget drivers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In cases where we're given an SG-list which is
longer than the amount of currently available TRBs,
we will be left with the same request on
started_list and we should prioritize that request
over possible new requests on pending_list. That's
a way to guarantee requests complete in order.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This will give us a simpler way of figuring out how
many bytes were left in each TRB. It's useful for
cases where we queue only part of an SG-list due to
amount of available TRBs at the time of kicking the
transfer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If XferNotReady comes before usb_ep_queue() we will
set our PENDING request flag and wait for a
request. However, originally, we were assuming
usb_ep_queue() would always happen before our first
XferNotReady and that causes a corner case where we
could try to issue ENDTRANSFER command before
STARTTRANSFER.
Let's fix that by tracking endpoints which have been
started.
Reported-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of just delaying for 100us, we should
actually wait for End Transfer Command Complete
interrupt before moving on. Note that this should
only be done if we're dealing with one of the core
revisions that actually require the interrupt before
moving on.
[ felipe.balbi@linux.intel.com: minor improvements ]
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The combo of list_empty() check and return list_first_entry()
can be replaced with list_first_entry_or_null().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When we change the USB function with configfs dynamically, we possibly
met this situation: one core is doing the control transfer, another core
is trying to unregister the USB gadget from userspace, we must wait for
completing this control tranfer, or it will hang the controller to set
the DEVCTRLHLT flag.
[ felipe.balbi@linux.intel.com: several fixes to the patch
- call complete() before starting following SETUP transfer
- add a macro for ep0_in_setup's timeout
- change commit subject slightly
- break lines at 72 characters (git adds an 8-character tab)
- avoid changes to dwc3_gadget_run_stop() ]
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
That function is unnecessarily called from
dwc3_gadget_reset_interrupt(). Gadget drivers (and
thus, functions) are required to dequeue all pending
requests when they get notified about a USB Bus
Reset.
Trying to make sure there are no pending requests
only serves the purpose of working around possibly
bad gadgets.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This helper will be responsible for reading and
parsing our properties. No functional changes in
this patch, cleanup only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This little helper will be used to setup anything
related to GCTL register. There are no functional
changes, this is a cleanup only patch.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This little helper will be used to make sure we're
dealing with a valid Synopsys DWC3 or DWC3.1 core.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For the usb31 IP and from version 2.90a of the usb3 IP, the core
supports HW exit from L1 in HS. Enable it, otherwise the controller may
never exit from LPM to do a transfer.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Member @mem in struct dwc3 is not used in any places. Clean up it.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We should never kill the machine just because some
USB endpoint type is wrong. WARN about it and move
on.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We don't need to know about short packets unless
gadget driver told us it's not ok to see them on the
bus. In the normal situation we can continue
processing the list of requests if we get a Short
packet.
Also, note that we're making sure ISP is only set
for OUT endpoints, where that setting is valid.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
CSP bit is only valid for OUT endpoints. Synopsys
databook is unclear if HW ignores CSP for IN
endpoints (chances are, it does) but to avoid
problems, let's make sure to set CSP only when valid
to do so.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By extracting smaller functions from
dwc3_ep0_handle_feature(), it becomes far easier to
understand what's going on. Cleanup only, no
functional changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We want to reduce the usage of dwc3_trace() in favor
of proper tracepoints which can be enabled/disabled
by the user. Let's start with our register
accessors.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We shouldn't have any glue layer which doesn't
compile everywhere. In order to make sure this is
always the case, make sure COMPILE_TEST is properly
added at dependency list of a config entry.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We don't need dwc3_trace() unless we're building a
kernel with CONFIG_FTRACE. This patch reduces
dwc3.ko text size a bit while also removing overhead
of dwc3_trace() calls.
text data bss dec hex filename
50796 581 0 51377 c8b1 drivers/usb/dwc3/dwc3.o
43961 581 0 44542 adfe drivers/usb/dwc3/dwc3.o.patched
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We can offset the latency of a full Start Transfer
command - where we _must_ poll for its completion -
to usb_ep_enable() time. This means that once
requests start showing up from the gadget driver, we
can rely on No Response Update Transfer command -
where we don't need to poll for completion.
This patch, starts implementing this method for Bulk
endpoints, even though, technically, we could extend
it to all other endpoints in future commits.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case of periodic transfers, let's pretty print
the size field as a multiplier followed by length,
such as :
3x 1024
instead of:
33555456
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With this extra piece of information, it will be
easier to find mismatches between driver and HW.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We will be using dwc3_ep0_state_string() from within
our tracepoints, so we need to move that helper to
debug.h in order for it to be accessible.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Removing some trace prints which were made redundant
when we started decoding events and TRBs completely
within their respective trace points.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC3 can tell us which phase of a setup transfer
we're getting into. Let's decode it from the event
to make it easier to debug.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link State Change events are only needed for
debugging and to apply certain workarounds on known
errata. Let's save a few cycles by disabling these
events completely on working revisions of the core.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There might be situations where a Start Transfer
command might fail, if that ever happens, instead of
simply removing the request from our list, we should
give the request back to the gadget driver,
otherwise we might eventually starve it from requests.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
No Response Update Transfer is a special type of
Update Transfer command which can be used whenever
we're not relying on XferNotReady to prepare
transfers. With this, we don't need to wait for
CMDACT to be cleared and issue further commands to
the endpoint straight away.
Let's start using this version to skip the long-ish
wait.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The cmd argument we pass to
dwc3_send_gadget_ep_cmd() could contain extra
arguments embedded. When checking for StartTransfer
command, we need to make sure to match only lower 4
bits which contain the actual command and ignore the
rest.
Reported-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case of High-Speed, High-Bandwidth endpoints, we
need to tell DWC3 that we have more than one packet
per interval. We do that by setting PCM1 field of
Isochronous-First TRB.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3-st uses pinctrl_pm_select_*_state() however it
doesn't include the necessary header. Fix the build
break caused by that, by simply including the
missing header.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In commit 2abd9d5fa6 ("usb: dwc3: ep0: Add chained TRB support"), the
size of the memory allocated with 'dma_alloc_coherent()' has been modified
but the corresponding calls to 'dma_free_coherent()' have not been updated
accordingly.
This has been spotted with coccinelle, using the following script:
////////////////////
@r@
expression x0, x1, y0, y1, z0, z1, t0, t1, ret;
@@
* ret = dma_alloc_coherent(x0, y0, z0, t0);
...
* dma_free_coherent(x1, y1, ret, t1);
@script:python@
y0 << r.y0;
y1 << r.y1;
@@
if y1.find(y0) == -1:
print "WARNING: sizes look different: '%s' vs '%s'" % (y0, y1)
////////////////////
Fixes: 2abd9d5fa6 ("usb: dwc3: ep0: Add chained TRB support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We cannot pre-start isochronous endpoints because we
rely on the micro-frame number passed via
XferNotReady command for proper Isochronous
scheduling.
Fixes: 08a36b5438 ("usb: dwc3: gadget: simplify __dwc3_gadget_ep_queue()")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some requests could be accounted for multiple
times. Let's fix that so each and every requests is
accounted for only once.
Cc: <stable@vger.kernel.org> # v4.8
Fixes: 55a0237f8f ("usb: dwc3: gadget: use allocated/queued reqs for LST bit")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This time around we have 92 non-merge commits. Most
of the changes are in drivers/usb/gadget (40.3%)
with drivers/usb/gadget/function being the most
active directory (27.2%).
As for UDC drivers, only dwc3 (26.5%) and dwc2
(12.7%) have really been active.
The most important changes for dwc3 are better
support for scatterlist and, again, throughput
improvements. While on dwc2 got some minor stability
fixes related to soft reset and FIFO usage.
Felipe Tonello has done some good work fixing up our
f_midi gadget and Tal Shorer has implemented a nice
API change for our ULPI bus.
Apart from these, we have our usual set of
non-critical fixes, spelling fixes, build warning
fixes, etc.
-----BEGIN PGP SIGNATURE-----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=vTFa
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.9 merge window
This time around we have 92 non-merge commits. Most
of the changes are in drivers/usb/gadget (40.3%)
with drivers/usb/gadget/function being the most
active directory (27.2%).
As for UDC drivers, only dwc3 (26.5%) and dwc2
(12.7%) have really been active.
The most important changes for dwc3 are better
support for scatterlist and, again, throughput
improvements. While on dwc2 got some minor stability
fixes related to soft reset and FIFO usage.
Felipe Tonello has done some good work fixing up our
f_midi gadget and Tal Shorer has implemented a nice
API change for our ULPI bus.
Apart from these, we have our usual set of
non-critical fixes, spelling fixes, build warning
fixes, etc.
Add necessary compatible flag for Cavium's DWC3 so
dwc3-of-simple will probe.
Tested-by: Steven J. Hill <Steven.Hill@cavium.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of erroring out when we don't have clocks,
let's just avoid any calls to the clk API.
Tested-by: Steven J. Hill <Steven.Hill@cavium.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In dwc3_of_simple_remove() we are using clk_unprepare() before doing
any clk_disable(). If we enable Common CLK framework (CCF) and try to
unbind dwc3-of-simple driver, we see kernel WARN messages.
This patch fixes this kernel warning by using clk_disable_unprepare()
instead of clk_unprepare().
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit 50c763f8c1 ("usb: dwc3: Set the ClearPendIN bit on Clear
Stall EP command") sets ClearPendIN bit for all IN endpoints of
v2.60a+ cores. This causes ClearStall command fails on 2.60+ cores
operating in HighSpeed mode.
In page 539 of 2.60a specification:
"When issuing Clear Stall command for IN endpoints in SuperSpeed
mode, the software must set the "ClearPendIN" bit to '1' to
clear any pending IN transcations, so that the device does not
expect any ACK TP from the host for the data sent earlier."
It's obvious that we only need to apply this rule to those IN
endpoints that currently operating in SuperSpeed mode.
Fixes: 50c763f8c1 ("usb: dwc3: Set the ClearPendIN bit on Clear Stall EP command")
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cleaning up the loop in dwc3_cleanup_done_reqs() introduced a
gcc warning if built with "-Wmaybe-uninitialized":
drivers/usb/dwc3/gadget.c: In function 'dwc3_endpoint_transfer_complete':
drivers/usb/dwc3/gadget.c:2015:9: 'trb' may be used uninitialized in this function [-Wmaybe-uninitialized]
I believe it is a false positive and we always have a valid 'trb'
pointer at the end of the function, but neither I nor the compiler
are able to prove that.
This works around the warning by computing a flag earlier in the function
when it's guaranteed to be valid, which tells the compiler that it's
safe and makes it easier to understand to me.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 31162af447 ("usb: dwc3: gadget: avoid while (1) loop on completion")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When building a kernel with CONFIG_PM_SLEEP=n, we
get the following warning:
drivers/usb/dwc3/dwc3-pci.c:253:12: warning: 'dwc3_pci_pm_dummy' defined but not used
In order to fix this, we should only define
dwc3_pci_pm_dummy() when CONFIG_PM_SLEEP is defined.
Fixes: f6c274e11e ("usb: dwc3: pci: runtime_resume child device")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch follows the similar fix in dwc2. See
commit 5268ed9d2e ("usb: dwc2: Fix dr_mode validation")
Currently, the dr_mode is only checked against the module configuration.
It also needs to be checked against the hardware capablities.
The driver now checks if both the module configuration and hardware are
capable of the dr_mode value. If not, then it will issue a warning and
fall back to a supported value. If it is unable to fall back to a
suitable value, then the probe will fail.
Behavior summary:
module : actual
HW config dr_mode : dr_mode
---------------------------------
host host any : host
host dev any : INVALID
host otg any : host
dev host any : INVALID
dev dev any : dev
dev otg any : dev
otg host any : host
otg dev any : dev
otg otg any : dr_mode
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
ulpi_register_interface() accepts a const struct ulpi_ops and dwc3
doesn't perform any changes to this struct at runtime, so there's no
reason it shouldn't be constant.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With the removal of the old {read|write} operations, we can now safely
rename the new api operations {read|write}_dev to use the shorter and
clearer names {read|write}, respectively.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The old read, write callbacks in struct ulpi_ops have been deprecated
in favor of new callbacks that pass the parent device directly.
Replace the used callbacks in dwc3's ulpi component with the new api.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts commit 6f8245b4e3 ("usb: dwc3: gadget: always decrement
by 1").
We can't always decrement this value.
We should decrement only if the calculation of free slots results in a
LINK TRB being among one of the free slots (dequeue < enqueue).
Otherwise, if the LINK TRB is not among the free slots then it should
not be decremented.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case our TRB ring is full, we can avoid trying to
kick transfers which won't start and just add requests
to the queue.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
ENDXFER polling is available on version 3.10a and later of the
DWC_usb3 (USB 3.0) controller. With this feature, the software can poll
the CMDACT bit in the DEPCMD register after issuing an ENDXFER command.
This feature is enabled by writing GUCTL2[14].
This feature is NOT available on the DWC_usb31 (USB 3.1) IP.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add revision number constants for the 3.00a and 3.10a releases.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When dwc3 core enters into suspend mode, the system (especially for mobile
device) may power off the dwc3 controller for power saving, that will cause
dwc3 controller lost the mode operation when resuming dwc3 core.
Thus we can move the mode setting into dwc3_core_init() function to avoid this
issue.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Rockchip platform merely enable usb3 clocks and
populate its children. So we can use this generic
glue layer to support Rockchip dwc3.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a quirk to clear the GUSB3PIPECTL.DELAYP1TRANS bit,
which specifies whether disable delay PHY power change
from P0 to P1/P2/P3 when link state changing from U0
to U1/U2/U3 respectively.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Support to configure the UTMI+ PHY with an 8- or 16-bit
interface via DT. The UTMI+ PHY interface is a hardware
capability, and it's platform dependent. Normally, the
PHYIF can be configured during coreconsultant.
But for some specific USB cores(e.g. rk3399 SoC DWC3),
the default PHYIF configuration value is false, so we
need to reconfigure it by software.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a quirk to clear the GUSB2PHYCFG.U2_FREECLK_EXISTS bit,
which specifies whether the USB2.0 PHY provides a free-running
PHY clock, which is active when the clock control input is active.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Upon transfer completion after a full ring, let's
add more TRBs to our ring in order to complete our
request successfully.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There was a typo when generating endpoint name which
would be very confusing when debugging. Fix it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If the ring is full and we are processing a big
sglist, then let's interrupt so we can, later, add
more TRBs to the ring.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
These two fields will be used in a follow-up patch
to track how many entries of request's sglist we
have already processed. The reason is that if a
gadget driver sends an sglist with more entries then
we can fit in the ring, we will have to continue
processing remaining afterwards.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We know that we have to iterate over the list of
started requests. Instead of looping forever, we can
rely on list_for_each_entry(). Likewise, instead of
a do {} while loop over all, maybe available,
scatterlist entries, we can detect if $this request
uses scatterlist and rely on for_each_sg().
This makes the code easier to follow while making
sure that we will *always* break out of the loop.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Many of the comments in that function are really
outdated and don't match what the driver is
doing. Moreover, recent patches combined programming
model for all non-control endpoints, this gives us
an opportunity to get rid of our special cases in
__dwc3_gadget_ep_queue().
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We always need to decrement our index by at least
one. Simplify the implementation by using a
temporary local variable and making sure that we
will always decrement one extra if tmp == 0.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of waiting until giveback before
incrementing the dequeue pointer, we can increment
it from dwc3_cleanup_done_reqs(), that way we avoid
an extra loop over all TRBs during giveback.
While at that, also avoid using req->first_trb_index
as that's completely unnecessary. A follow-up patch
will clean up further uses of that and remove the
field altogether.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The only endpoint which actually requires LST bit
and XferComplete is ep0/1. Let's save some time by
completely removing LST bit support and
XferComplete.
This simplifies and consolidates endpoint handling
for all other 3 transfer types while also avoiding
extra interrupts.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
__dwc3_gadget_wakeup() is called while holding a spinlock, then depends on
jiffies in order to timeout while polling the USB core for a link state
update. In the case the wakeup failed, the timeout will never happen and
will also cause the cpu to stall until rcu_preempt kicks in.
This switches to a "decrement variable and wait" timeout scheme.
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After going through runtime_suspend/runtime_resume
cycle once we would be left with an unbalanced
pm_runtime_get() call. Fix that by making sure that
we try to suspend right after resuming so things are
balanced and device can runtime_suspend again.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
During runtime_resume of dwc3-pci.c, we need to
runtime suspend our child device (which is dwc3
proper) otherwise nothing will happen.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
stop consuming TRBs when we reach one with HWO bit
already set. This will prevent us from prematurely
retiring a TRB.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to Synopsys Databook 2.60a, section 8.3.4,
it's stated that:
The LST bit should be set to 0 (isochronous
transfers normally continue until the
endpoint is removed entirely, at which time
an End Transfer command is used to stop the
transfer).
This patch makes sure that detail is observed and
fixes a regression with Android Audio playback
caused by recent changes to DWC3 gadget.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add missing platform_set_drvdata() in dwc3_of_simple_probe(), otherwise
calling platform_get_drvdata() in remove returns NULL.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Intel Kabylake PCH has the same DWC3 than Intel
Sunrisepoint. Add the new ID to the supported devices.
Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If we stop earlier due to short packet, we will
not be able to giveback all TRBs.
Cc: <stable@vger.kernel.org>
Cc: Brian E Rogers <brian.e.rogers@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC3 has one interesting peculiarity with chained
transfers. If we setup N chained transfers and we
get a short packet before processing all N TRBs,
DWC3 will (conditionally) issue a XferComplete or
XferInProgress event and retire all TRBs from the
one which got a short packet to the last without
clearing their HWO bits.
This means SW must clear HWO bit manually, which
this patch is doing.
Cc: <stable@vger.kernel.org>
Cc: Brian E Rogers <brian.e.rogers@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When using SG lists, we would end up setting
request->actual to:
num_mapped_sgs * (request->length - count)
Let's fix that up by incrementing request->actual
only once.
Cc: <stable@vger.kernel.org>
Reported-by: Brian E Rogers <brian.e.rogers@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The whole Kconfig entries of the USB subsystem are surrounded with
"if USB_SUPPORT" ... "endif", so CONFIG_USB_SUPPORT=y is surely met
when these two Kconfig options are visible.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=PpU9
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-4.7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull more MFD fixes from Lee Jones:
"Apologies for missing these from the first pull request.
Final patches fixing Reset API change"
* tag 'mfd-fixes-4.7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
usb: dwc3: st: Use explicit reset_control_get_exclusive() API
phy: phy-stih407-usb: Use explicit reset_control_get_exclusive() API
phy: miphy28lp: Inform the reset framework that our reset line may be shared
Looks like we lost all changes related to
commit 9522def400 ("usb: dwc3: core: cleanup IRQ resources") in host.c
when Felipe's next branch was merged into Greg's next branch.
Fixes 215db94818 ("Merge tag 'usb-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're making all reset line users specify whether their lines are
shared with other IP or they operate them exclusively. In this case
the line is exclusively used only by this IP, so use the *_exclusive()
API accordingly.
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- Use new reset_*_get_shared() variant to prevent reset line obtainment failure
- Fixes: 0b52297 ("reset: Add support for shared reset controls")
- Fix unintentional switch() fall-through into error path
- Fix uninitialised variable compiler warning
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=mo7m
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD fixes from Lee Jones:
"Contained are some standard fixes and unusually an extension to the
Reset API. Some of those changes are required to fix a bug introduced
in -rc1, which introduces extra 'reset line checks' i.e. whether the
line is shared or not. If a line is shared and the new *_shared() API
is not used, the request fails with an error. This breaks USB in v4.7
for ST's platforms.
Admittedly, there are some patches contained in our (MFD/Reset)
immutable branch which are not true -fixes, but there isn't anything I
can do about that. Rest assured though, there aren't any API
'changes'. Everything is the same from the consumer's perspective.
- Use new reset_*_get_shared() variant to prevent reset line
obtainment failure (Fixes commit 0b52297f2288: "reset: Add support
for shared reset controls")
- Fix unintentional switch() fall-through into error path
- Fix uninitialised variable compiler warning"
* tag 'mfd-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: da9053: Fix compiler warning message for uninitialised variable
mfd: max77620: Fix FPS switch statements
phy: phy-stih407-usb: Inform the reset framework that our reset line may be shared
usb: dwc3: st: Inform the reset framework that our reset line may be shared
usb: host: ehci-st: Inform the reset framework that our reset line may be shared
usb: host: ohci-st: Inform the reset framework that our reset line may be shared
reset: TRIVIAL: Add line break at same place for similar APIs
reset: Supply *_shared variant calls when using *_optional APIs
reset: Supply *_shared variant calls when using of_* API
reset: Ensure drivers are explicit when requesting reset lines
reset: Reorder inline reset_control_get*() wrappers
On the STiH410 B2120 development board the MiPHY28lp shares its reset
line with the Synopsys DWC3 SuperSpeed (SS) USB 3.0 Dual-Role-Device
(DRD). New functionality in the reset subsystems forces consumers to
be explicit when requesting shared/exclusive reset lines.
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here's the big pull request for Peripheral stack and
all related drivers.
This time around with 109 non-merge commits mostly
concentrated on drivers/usb/gadget/udc (41.5%) and
drivers/usb/dwc3 (28.1%).
There's a big rework on dwc3's transfer handling
which gave us almost 3x faster USB3 speeds with Mass
Storage on a particular test scenario I measured. We
are also removing platform_data from dwc3 after
converting all users to built-in properties instead.
For the Gadget API, we're just adding tracepoints to
aid debugging activities.
Other than these, there's the usual set of spelling
fixes, minor bug fixes and sparse warnings cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=PT1e
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.8 merge window
Here's the big pull request for Peripheral stack and
all related drivers.
This time around with 109 non-merge commits mostly
concentrated on drivers/usb/gadget/udc (41.5%) and
drivers/usb/dwc3 (28.1%).
There's a big rework on dwc3's transfer handling
which gave us almost 3x faster USB3 speeds with Mass
Storage on a particular test scenario I measured. We
are also removing platform_data from dwc3 after
converting all users to built-in properties instead.
For the Gadget API, we're just adding tracepoints to
aid debugging activities.
Other than these, there's the usual set of spelling
fixes, minor bug fixes and sparse warnings cleanups.
This should allow xhci to remove handling of platform data.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It had changed to be suspend event for BIT6 in DEVT register from
version 2.30a and above. Thus this patch introduces one suspend
event handler to handle the suspend event.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Implementations might use different IRQs for
host, gadget so use named interrupt resources
to allow device tree to specify the interrupts.
Following are the interrupt names
Peripheral Interrupt - peripheral
HOST Interrupt - host
Maintain backward compatibility for a single named
interrupt ("dwc3_usb3") for all interrupts as well as
unnamed interrupt at index 0 for all interrupts.
As platform_get_irq() variants are used, tackle
the -EPROBE_DEFER case as well.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It will be crash to stop gadget when the dwc3 device had been into suspend
state, thus we need to check if the dwc3 device had been into suspend state
when UDC try to stop gadget.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Because of recent changes to transfer handling on
DWC3, we will not get XferComplete unless we
completely fill up our TRB ring. This means that we
might get a Reset or Disconnect without getting a
XferComplete first.
In order to correctly release our allocated Transfer
Resource, we must issue ENDTRANSFER command whenever
dep->resource_index is valid.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If there is a failure after pm_runtime_enable/get_sync()
we need to call pm_runtime_disable/put_sync().
Otherwise it will lead to an unbalanced pm_runtime_enable() on the
subsequent probe if the earlier probe bailed out due to -EPROBE_DEFER.
pm_runtime_get_sync() can fail as well so deal with that case too.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
it's clear now that when is_on=true, we must loop
until DWC3_DSTS_DEVCTRLHLT clears; while when
is_on=false we must loop until DWC3_DSTS_DEVCTRLHLT
gets set.
Instead of adding actual if() statements, we can
rely on XOR operation to evaluate to true only when
the above conditions apply. Then, we can move the
break condition back to the while() statement
together with our timeout check and the resulting
code is very compact and simpler to read.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of looping forever and forcing a return if
timeout reaches zero, we can just use timeout and
loop's break condition directly.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
testing shows that udelay() is unnecessary as
controller reaches Halted state almost
instantenously as can be seen by our timeout
variable never actually decrementing.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We shouldn't change a host-only dwc3 to gadget-only
if driver is built as gadget-only. Fix that up here.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's know that Intel's SoCs' dwc3 integration is
peripheral-only since Intel implements its own
portmux for role-swapping. In order to prevent dwc3
from ever registering and XHCI platform_device,
let's just set dr-mode to peripheral-only on Intel
SoCs.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
'modify' is what the current action is called. Let's
rename it so it matches databook. While at that,
also make sure to add support 'init' action too.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now we can try to issue Update Transfer every time
gadget driver queues a new request. This will make
sure we keep controller's queue busy for as long as
possible.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Let's only set LST bit when we run out of space in
our TRB ring. For all other cases, we keep LST bit
unset which will prevent constant allocation and
deallocation of endpoint transfer resources.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of relying on empty list of queued requests,
let's rely on the fact that we have a TRB being
processed right now.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We will be using this information to change how we
figure out when we need LST bit. For now, just
update our counters.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to SNPS databook, we need to pass transfer
resource on update transfer command, let's do it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
No more users for it.
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This should allow the core driver to drop handling of
platform data and expect the platform specific details to
always come from properties.
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Huang Rui <ray.huang@amd.com>
CC: John Youn <John.Youn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
when passing strings to trace, we don't need the
trailing newline character. Trace already appends a
newline character automatically.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Don't make any decisions regarding VBUS session based on ID
status. That is best left to the OTG core.
Pass ID and VBUS events independent of each other so that OTG
core knows exactly what to do.
This makes dual-role with extcon work with OTG irq on OMAP platforms.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
TRM [1] recommends that POWERPRESENT bit must not be
set and left at it's default value of 0.
[1] OMAP542x TRM - http://www.ti.com/lit/pdf/swpu249
Section 23.11.4.5.1 Mailbox VBUS/ID Management
"Because PIPE powerpresent has a different meaning in host and in device mode,
and because of the redundancy with the UTMI signals, the controller ORes
together the appropriate PIPE and UTMI inputs to create its internal
VBUS status. For that reason, it is recommended to leave field
USBOTGSS_UTMI_OTG_STATUS[9] POWERPRESENT at its default value (=0), and only to
fill in the USB2 VBUS status fields in the same register."
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On OMAPs, OTG events come on the same IRQ so we need to share
this IRQ with the OTG device driver.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We intend to share this interrupt with the OTG driver an to ensure
that irqflags match for the shared interrupt handlers we use
request_threaded_irq()
If we don't use request_treaded_irq() then forced threaded irq will
set IRQF_ONESHOT and this won't match with the OTG IRQ handler's
IRQ flags.
NOTE: OTG IRQ handler is yet to be added. This is a preparatory step.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
GUCTL1 reg has some useful functions which can be
written by user. For rockchip platform, we set
GUCTL1.DEV_FORCE_20_CLK_FOR_30_CLK (bit26, applicable
for the core is programmed to operate in 2.0 device
only) to 1 in bootrom, and after start the kernel,
we want to check whether this bit can be reset to
default 0 after the core reset. Dump GUCTL1 reg from
debugfs is more convenient for us.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The DWC3_USB31_REVISION_110A macro uses an invalid constant name in its
definition. This is currently not used.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Correct the use of the DWC3_DSTS_XXX_SPEED and DWC3_DCFG_XXX_SPEED
macros. The wrong set of macros were being used in a few places.
This is only a cosmetic change as the values for both sets are
identical.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
From sparse:
warning: cast truncates bits from constant value (100 becomes 0)
The DWC3_TRB_NUM constant is too big for u8. Do the calculation a
slightly different way that should still be optimized out for the case
where DWC3_TRB_NUM == 256.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If the trb->enqueue == trb->dequeue, then it could be full or empty.
This could also happen at TRB index 0, so modify the check to handle
that condition. At index 0, the previous TRB is the one just before the
link TRB.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The TRBs left calculation didn't account for the link TRB taking up one
spot.
If the trb_dequeue < trb_enqueue, then the result includes the link
TRB slot so it must be adjusted.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The current calculation takes dep->trb_dequeue - dep->trb_enqueue to
find the TRB space left.
If you enqueue 1, that results in:
(u8) 0 - (u8) 1 = 0xff = 255 TRBs left.
This is correct if DWC3_TRB_NUM == 256.
If DWC3_TRB_NUM is less than 256 (but still a power of 2) you need to
mod the result by DWC3_TRB_NUM.
For example the same calculation with DWC3_TRB_NUM = 8, results in:
255 % 6 = 7 TRBs left.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If trbs_left == 0, we don't have any space left in the TRB ring so don't
prepare anything.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Clears out all the TRBs in the ring to clean up any stale data that
might be in them from the previous time the endpoint was enabled.
Also removed the existing clear of the LINK trb since the entire ring is
cleard just before.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make the skipping of the link TRBS built-in to the increment operation.
This simplifies the code wherever we increment the trb index and ensures
that we never end up pointing to a link trb.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Sparse complains even though it looks ok. Probably it cannot detect that
the wValue, wIndex, and wLength are declared __le16 due to the macro
magic.
Redeclare them as CPU endianness and make the conversion on assignment.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cleans up the sparse warning:
warning: dubious: x | !y
Since we do want a bitwise OR here, don't use a logical (true/false)
value. Probably is not a real issue but it cleans up the warning.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
u2sel and u2pel should be __le16. Doesn't fix any issue.
Found with sparse.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The wIndex passed in here is CPU endianness, but the function expects
little endian.
Found with sparse.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Just like we did for endpoint commands, let's have a
single trace output for the command and its
status. This will improve trace readability
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Just like we did for endpoint commands, let's use a
single return point for generic commands as
well. This aids readability.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of printing command's status with a separate
trace printout, let's print it within a single call.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of having infinite loop and always checking
timeout value as a break condition, we can just
decrement timeout inside while's condition.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
I really thought this would be useful, but as it
turns out, it creates more problems than fixes. The
amount of times we had to fix this because some
other commit shuffled things around and ended up
regressing this tiny little string manupulation...
Might as well remove it, since it has a negligible
added benefit.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Improve trb tracing by showing trb flags, interrupts
trb type.
trb flags:
- h - hardware owner of descriptor
- l - last TRB
- c - chain buffers
- s - continue on short packet
interrupt flags:
- s - interrupt on short packet
- c - interrupt on complete
Capital letter means that bit is set, while
lowercase letter means bit is cleared.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This will allow us to process several endpoints at a
time by making sure that we lock only shared
resources.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Allow for dwc3-pci to reach D3 and enable pm_runtime
by providing dummy PM hooks. Without them, PCI
subsystem won't put device to D3.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
this patch implements the most basic pm_runtime
support for dwc3. Whenever USB cable is dettached,
then we will allow core to runtime_suspend.
Runtime suspending will involve completely tearing
down event buffers and require a full soft-reset of
the IP.
Note that a further optimization could be
implemented once we decide to support hibernation,
which is to allow runtime_suspend with cable
connected when bus is in U3. That's subject to a
separate patch, however.
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
when we call dwc3_gadget_giveback(), we end up
releasing our controller's lock. Another thread
could get scheduled and disable the endpoint,
subsequently setting dep->endpoint.desc to NULL.
In that case, we would end up dereferencing a NULL
pointer which would result in a Kernel Oops. Let's
avoid the problem by simply returning early if we
have a NULL descriptor.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
commit f3af36511e ("usb: dwc3: gadget: always
enable IOC on bulk/interrupt transfers") ended up
regressing Isochronous endpoints by clearing
DWC3_EP_BUSY flag too early, which resulted in
choppy audio playback over USB.
Fix that by partially reverting original commit and
making sure that we check for isochronous endpoints.
Fixes: f3af36511e ("usb: dwc3: gadget: always enable IOC
on bulk/interrupt transfers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Konrad Leszczynski <konrad.leszczynski@intel.com>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As a micro-power optimization, let's only resume the
USB2 PHY if we're working on <=HIGHSPEED. If we're
gonna work on SUPERSPEED or SUPERSPEED+, there's no
point in resuming the USB2 PHY.
Fixes: 2b0f11df84 ("usb: dwc3: gadget: clear SUSPHY bit before ep cmds")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
by holding gadget's IRQ number in dwc->irq_gadget,
it'll be simpler to free_irq() and disable the IRQ
in case an IRQ fires while we are runtime suspended.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
now that we have re-factored dwc3_core_init() and
dwc3_core_exit() we can use them for suspend/resume
operations.
This will help us avoid some common mistakes when
patching code when we have duplicated pieces of code
doing the same thing.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The idea of this patch is for dwc3_core_init() to
abstract all the details about how to initialize
dwc3 and dwc3_core_exit() to do the same for
teardown.
With this, we can simplify suspend/resume operations
by a large margin and always know that we're going
to start dwc3 from a known starting point.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
this patch is in preparation for some further
re-factoring in dwc3 initialization. No functional
changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By adding a pointer to endpoint registers' base
address, we can avoid using our controller-wide
struct dwc3 pointer for everything. At some point
this will allow us to have per-endpoint locks which
will, in turn, let us queue requests to separate
endpoints in parallel.
Because of this change our debugfs interface and io
accessors need to be changed accordingly.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In all call sites of dwc3_send_gadget_ep_cmd() we
already had a valid dep pointer, so instead of
passing dwc and dep->number, which would be used to
fetch the same pointer we already had, just pass dep
directly.
In other words, we're changing:
struct dwc3_ep *dep = dwc[dep->number];
to just passing struct dwc3_ep *dep as argument.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of using burst size to configure NUMP, we
should be using RxFIFO Size instead. DWC3 is smart
enough to know that it shouldn't burst in case burst
size is 0.
Reported-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
To aid code readability, we're gonna split
__dwc3_gadget_kick_transfer() into its constituent
parts: scatter gather and linear buffers.
That way, it's easier to follow the code and focus
debug effort when one or the other fails.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of returning -EINVAL when someone calls
__dwc3_gadget_wakeup() in speeds > highspeed, let's
return 0. There are no problems for the driver for
calling it in superspeed as we cleanly just return.
This avoids an annoying WARN_ONCE() always
triggering during superspeed enumeration with LPM
enabled.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When we send an endpoint command, we want that to
complete as soon as possible, so let's remove the
unnecessary udelay(1) call.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
sg_is_last() and list_is_last() will encode the
required information for the driver to make
decisions WRT CHN and LST bits.
While at that, also replace '1' with 'true' for
consistency.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
as it turns out, we don't need the extra 'start_new'
argument as that can be inferred from DWC3_EP_BUSY
flag.
Because of that, we can simplify
__dwc3_gadget_kick_transfer() by quite a bit, even
allowing us to prepare more TRBs unconditionally.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If we're updating transfers, we can also prepare as
many TRBs as we can fit in the ring. Let's start
doing that.
This patch 'solves' a limitation of how many TRBs we
can prepare when we're getting close the end of the
ring. Instead driver to prepare only up to end of
the ring, we check if we have space to wrap around
the ring properly.
Note that this only happens when our enqueue and
dequeue pointers are equal (which is the case for
bulk endpoints after an XferComplete event).
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of trying hard to stay connected to the
host, it's best (and far easier) to disconnect from
the host already.
Anything relying on KEEP_CONNECT will just have that
ignored, but we don't have proper hibernation
implementation yet, so there are no regressions.
In any case, hibernation is only useful for runtime
PM, not system sleep.
While at that, also remove dwc3.dcfg which has been
rendered unnecessary.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we will be re-using it for suspend/resume, so
instead of duplicating code, let's just re-factor
the functions so they can be re-used.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As of core revision 2.60a the recommended programming model is to set
the ClearPendIN bit when issuing a Clear Stall EP command for IN
endpoints. This is to prevent an issue where some (non-compliant) hosts
may not send ACK TPs for pending IN transfers due to a mishandled error
condition. Synopsys STAR 9000614252.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Set USB3_FORCE_VBUSVALID when configured for USB_DR_MODE_PERIPHERAL
mode, as it is required to have a working setup.
This worked on the internal driver by relying on the reset
value of the syscfg register as the bits aren't explicity cleared
and set like the upstream driver.
Also add a comment about what setting this bit means.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3-exynos has two problems during init if the regulators are slow
to come up (for instance if the I2C bus driver is not on the initramfs)
and return probe deferral. First, every time this happens, the driver
leaks the USB phys created; they need to be deallocated on error.
Second, since the phy devices are created before the regulators fail,
this means that there's a new device to re-trigger deferred probing,
which causes it to essentially go into a busy loop of re-probing the
device until the regulators come up.
Move the phy creation to after the regulators have succeeded, and also
fix cleanup on failure. On my ODROID XU4 system (with Debian's initramfs
which doesn't contain the I2C driver), this reduces the number of probe
attempts (for each of the two controllers) from more than 2000 to eight.
Signed-off-by: Steinar H. Gunderson <sesse@google.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Fixes: d720f057fd ("usb: dwc3: exynos: add nop transceiver support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the original DWC3_DCFG_NUMP() was always zero. It looks like the
intent was to shift first and then do the mask.
Fixes: 2a58f9c12b ('usb: dwc3: gadget: disable automatic calculation of ACK TP NUMP')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big USB Gadget pull request. This time
not as large as usual with only 57 non-merge
commits.
The most important part here is, again, all the work
on dwc3. This time around we're treating all
endpoints (except for control endpoint) exactly the
same. They all have the same amount of TRBs on the
ring, they all treat the ring as an actual ring with
a link TRB pointing to the head, etc.
We're also helping the host side burst (on
SuperSpeed GEN1 or GEN2 at least) for as long as
possible until the endpoint returns NRDY.
Other than this big TRB ring rework on dwc3, we also
have a dwc3-omap DMA initialization fix, some extra
debugfs files to aid in some odd debug sessions and
a complete removal of our FIFO resizing logic.
We have a new quirk for some dwc3 P3 quirk in some
implementations.
The rest is basically non-critical fixes and the
usual cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7szP
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.7 merge window
Here's the big USB Gadget pull request. This time
not as large as usual with only 57 non-merge
commits.
The most important part here is, again, all the work
on dwc3. This time around we're treating all
endpoints (except for control endpoint) exactly the
same. They all have the same amount of TRBs on the
ring, they all treat the ring as an actual ring with
a link TRB pointing to the head, etc.
We're also helping the host side burst (on
SuperSpeed GEN1 or GEN2 at least) for as long as
possible until the endpoint returns NRDY.
Other than this big TRB ring rework on dwc3, we also
have a dwc3-omap DMA initialization fix, some extra
debugfs files to aid in some odd debug sessions and
a complete removal of our FIFO resizing logic.
We have a new quirk for some dwc3 P3 quirk in some
implementations.
The rest is basically non-critical fixes and the
usual cleanups.
Now that we calculate DCFG.NUMP, we can disable
dwc3's automatic calculation so we maximize our
chances of very high throughtput through the use of
bursts.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
NumP field of DCFG register is used on NumP field of
ACK TP header and it tells the host how many packets
an endpoint can receive before waiting for
synchronization.
Documentation says it should be set to anything
<=bMaxBurst. Interestingly, however, this setting is
not per-endpoint how it should be (different
endpoints could have different burst sizes), but
things seem to work okay right now.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
if Start Transfer command fails, let's try a little
harder to figure out why the command failed and give
slightly better return codes. This will be usefulf
or isochronous endpoints, at least, which could
decide to retry a given request.
Signed-off-by: Konrad Leszczynski <konrad.leszczynski@intel.com>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For convenience, passing the dwc3 platform device as a
parameter to dwc3_pci_quirks() function.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Setting the ACPI companion before calling dwc3_pci_quirks.
The ACPI companion will be set unconditionally as the
primary fwnode, overriding any previously set primary
fwnode. This will make sure that any build-in properties
added to the platform device will be added as the secondary
fwnode in cases where also ACPI companion exists.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case host sends us an unsupported test mode, we
*must* stall this request. This will tell the host
that the selector is invalid and we won't put the
controller in unsupported test modes which could
have undetermined side-effects.
Signed-off-by: Fei Yang <fei.yang@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's a bunch of information in the debug register
set from dwc3 which is useful in some debugging
scenarios. Let's dump them out in endpoint-specific
directories and designated files.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This helper will be used later to convert trb type
into a human-readable string for debugfs.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
this helper will be used, initially, to dump space
of different queues and fifos in dwc3 to
debugfs. Later, it'll be used to issue remote wakeup
when we want to start a transfer and there's
something in a TX FIFO.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Debugfs init failure is not so important. We can continue our job on
this failure. Also no break need for debugfs_create_file call failure.
Signed-off-by: Du, Changbin <changbin.du@intel.com>
[felipe.balbi@linux.intel.com :
- remove out-of-memory message, we get that from OOM.
- switch dev_err() to dev_dbg() ]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dma_status bit flag is set but never really used
so get rid of it.
Reported-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It makes no sense to interrupt in the middle of
chained transfer. This patch just makes sure we
don't do that.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of limiting link TRB only to Isoc endpoints,
let's use it for all endpoint types, this way we are
more likely to transfer more data before a
XferComplete event.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By moving our % DWC3_NUM_TRB operation to the
increment helpers, the rest of the driver can be
simplified.
It's also a good practice to make sure we will have
a single place dealing with details about how to
increment our enqueue and dequeue pointers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add three little helpers which will aid in making
the code slightly easier to read. One helper
increments enqueue pointer, another increments
dequeue pointer and the last one tests if we're
dealing with the last TRB.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of using a bitwise and, let's rely on the %
operator since that's a lot more clear. Also, GCC
will optimize % 256 to nothing anyway.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We *know* that we have 1 PAGE (4096 bytes) for our
TRB poll. We also know the size of each TRB and know
that we can fit 256 of them in one PAGE. By using a
u8 type we can make sure that:
enqueue++ % 256;
gets optimized to an increment only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This makes it clear that we're dealing with a queue
of TRBs. No functional changes. While at that, also
rename start_slot to first_trb_index for similar
reasons.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The DWC3 OMAP driver supports DT-boot only, as result dma_mask will be
always configured properly from DT -
of_platform_device_create_pdata()->of_dma_configure(). More over,
dwc3-omap.c can be built as module and in this case it's unsafe to
assign local variable as dma_mask.
Hence, remove dma_mask configuration code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some freescale QorIQ platforms require to disable receiver detection
in P3 for correct detection of USB devices. If GUSB3PIPECTL(DISRXDETINP3)
is set, Core will change PHY power state to P2 and then perform receiver
detection. After receiver detection, Core will change PHY power state to
P3. Same quirk would be added in dts file in future patches.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Synopsys Databook says we should move link to U0
before issuing a Start Transfer command. We could
require the gadget driver to call
usb_gadget_wakeup() however I feel that changing all
gadget drivers to keep track of Link State and
conditionally call usb_gadget_wakeup() would be far
too much work. For now we will handle this at the
UDC level, but at some point composite.c should be
one handling this.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Synopsys Databook 2.60a has a note that if we're
sending an endpoint command we _must_ make sure that
DWC3_GUSB2PHY(n).SUSPHY bit is cleared.
This patch implements that particular detail.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_send_gadget_ep_cmd() had three return
points. That becomes a pain to track when we need to
debug something or if we need to add more code
before returning.
Let's combine all three return points into a single
one just by introducing a local 'ret' variable.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we don't plan on using multiple event buffers, but
if we find a good use case for it, this little trick
will help us avoid a loop in hardirq handler looping
for each and every event buffer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Gadget controller might not be always active during system
suspend/resume as gadget driver might not have yet been loaded or
might have been unloaded prior to system suspend.
Check if we're active and only then perform
necessary actions during suspend/resume.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc->regset is allocated on dwc3_debugfs_init, and should
be released on init failure or dwc3_debugfs_exit. Btw,
The line "dwc->root = NULL" is unnecessary, so remove it.
Signed-off-by: Du, Changbin <changbin.du@intel.com>
[ felipe.balbi@linux.intel.com : add another err label for the new
error condition ]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we need to power off the PHY during suspend and
power it back on during resume.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
[nsekhar@ti.com: fix call to usb_phy_set_suspend() in dwc3_suspend()]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Even if pm_runtime_get*() fails, we *MUST* call
pm_runtime_put_sync() before disabling PM.
While at it, remove superfluous dwc3_omap_disable_irqs()
in error path.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
[nsekhar@ti.com: patch description updates]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we will be using a single event buffer and that
renders ev_buffs array unnecessary. Let's remove it
in favor of a single pointer to a single event
buffer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We never, ever route any of the other event buffers
so we might as well drop support for them.
Until someone has a real, proper benefit for
multiple event buffers, we will rely on a single
one. This also helps reduce memory footprint of
dwc3.ko which won't allocate memory for the extra
event buffers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
request_list and req_queued were, well, weird naming
choices.
Let's give those better names and call them,
respectively, pending_list and started_list. These
new names better reflect what these lists are
supposed to do.
While at that also rename req->queued to req->started.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
previously we were using a maximum of 32 TRBs per
endpoint. With each TRB being 16 bytes long, we were
using 512 bytes of memory for each endpoint.
However, SLAB/SLUB will always allocate PAGE_SIZE
chunks. In order to better utilize the memory we
allocate and to allow deeper queues for gadgets
which would benefit from it (g_ether comes to mind),
let's increase the maximum to 256 TRBs which rounds
up to 4096 bytes for each endpoint.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
CSP bit of TRB Control is useful for protocols such
CDC EEM/ECM/NCM where we're transferring in blocks
of MTU-sized requests (usually MTU is 1500 bytes).
We know we will always have a short packet after two
(for HS) wMaxPacketSize packets and, usually, we
will have a long(-ish) queue of requests (for our
g_ether gadget, we have at least 10
requests).
Instead of always stopping the queue processing to
interrupt, giveback and restart, let's tell dwc3 to
interrupt but continue processing following request
if we have anything already pending in the queue.
This gave me a considerable improvement of 40% on my
test setup.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
That FIFO resizing logic was added to support OMAP5
ES1.0 which had a bogus default FIFO size. I can't
remember the exact size of default FIFO, but it was
less than one bulk superspeed packet (<1024) which
would prevent USB3 from ever working on OMAP5 ES1.0.
However, OMAP5 ES1.0 support has been dropped by
commit aa2f4b16f8 ("ARM: OMAP5: id: Remove ES1.0
support") which renders FIFO resizing unnecessary.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The Keystone 2 supports DT-boot only, as result dma_mask will be
always configured properly from DT -
of_platform_device_create_pdata()->of_dma_configure(). More over,
dwc3-keystone.c can be built as module and in this case it's unsafe to
assign local variable as dma_mask.
Hence, remove dma_mask configuration code.
Cc: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
BXT-M is a Intel Broxton SoC based platform with unique PCI ID.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We were exitting the function before actually
renaming anything. While at that, also always leave
control endpoint un-renamed.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's a requirement that we release controller's lock
while calling gadget API function pointers. This
patch just fixes that long standing bug.
Signed-off-by: Jiebing Li <jiebing.li@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to Synopsys Databook, we shouldn't be
relying on GCTL.CORESOFTRESET bit as that's only for
debugging purposes. Instead, let's use DCTL.CSFTRST
if we're OTG or PERIPHERAL mode.
Host side block will be reset by XHCI driver if
necessary. Note that this reduces amount of time
spent on dwc3_probe() by a long margin.
We're still gonna wait for reset to finish for a
long time (default to 1ms max), but tests show that
the reset polling loop executed at most 19 times
(modprobe dwc3 && modprobe -r dwc3 executed 1000
times in a row).
Suggested-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
new device support in terms of LoC, but there has been some cleanup
in the core as well as the usual minor clk additions to various
drivers.
Core:
- parent tracking has been simplified
- CLK_IS_ROOT is now a no-op flag, cleaning up drivers has started
- of_clk_init() doesn't consider disabled DT nodes anymore
- clk_unregister() had an error path bug squashed
- of_clk_get_parent_count() has been fixed to only return unsigned ints
- HAVE_MACH_CLKDEV is removed now that the last arch user (ARM) is gone
New Drivers:
- NXP LPC18xx creg
- QCOM IPQ4019 GCC
- TI dm814x ADPLL
- i.MX6QP
Updates:
- Cyngus audio clks found on Broadcom iProc devices
- Non-critical fixes for BCM2385 PLLs
- Samsung exynos5433 updates for clk id errors, HDMI support,
suspend/resume simplifications
- USB, CAN, LVDS, and FCP clks on shmobile devices
- sunxi got support for more clks on new SoCs and went through a minor
refactoring/rewrite to use a simpler factor clk construct
- rockchip added some more clk ids and added suport for fraction dividers
- QCOM GDSCs in msm8996
- A new devm helper to make adding custom actions simpler (acked by Greg)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=bZFY
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The clk changes for this release cycle are mostly dominated by new
device support in terms of LoC, but there has been some cleanup in the
core as well as the usual minor clk additions to various drivers.
Core:
- parent tracking has been simplified
- CLK_IS_ROOT is now a no-op flag, cleaning up drivers has started
- of_clk_init() doesn't consider disabled DT nodes anymore
- clk_unregister() had an error path bug squashed
- of_clk_get_parent_count() has been fixed to only return unsigned ints
- HAVE_MACH_CLKDEV is removed now that the last arch user (ARM) is gone
New Drivers:
- NXP LPC18xx creg
- QCOM IPQ4019 GCC
- TI dm814x ADPLL
- i.MX6QP
Updates:
- Cyngus audio clks found on Broadcom iProc devices
- Non-critical fixes for BCM2385 PLLs
- Samsung exynos5433 updates for clk id errors, HDMI support,
suspend/resume simplifications
- USB, CAN, LVDS, and FCP clks on shmobile devices
- sunxi got support for more clks on new SoCs and went through a
minor refactoring/rewrite to use a simpler factor clk construct
- rockchip added some more clk ids and added suport for fraction
dividers
- QCOM GDSCs in msm8996
- A new devm helper to make adding custom actions simpler (acked by Greg)"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (197 commits)
clk: bcm2835: fix check of error code returned by devm_ioremap_resource()
clk: renesas: div6: use RENESAS for #define
clk: renesas: Rename header file renesas.h
clk: max77{686,802}: Remove CLK_IS_ROOT
clk: versatile: Remove CLK_IS_ROOT
clk: sunxi: Remove use of variable length array
clk: fixed-rate: Remove CLK_IS_ROOT
clk: qcom: Remove CLK_IS_ROOT
doc: dt: add documentation for lpc1850-creg-clk driver
clk: add lpc18xx creg clk driver
clk: lpc32xx: fix compilation warning
clk: xgene: Add missing parenthesis when clearing divider value
clk: mb86s7x: Remove CLK_IS_ROOT
clk: x86: Remove clkdev.h and clk.h includes
clk: x86: Remove CLK_IS_ROOT
clk: mvebu: Remove CLK_IS_ROOT
clk: renesas: move drivers to renesas directory
clk: si5{14,351,70}: Remove CLK_IS_ROOT
clk: scpi: Remove CLK_IS_ROOT
clk: s2mps11: Remove CLK_IS_ROOT
...
Check that dwc->maximum_speed is set to a valid value. Also add an error
when we use it later if we encounter an invalid value.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Enable SuperSpeedPlus by programming the DCFG.speed and after
enumerating, set gadget->speed appropriately.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the maximum_speed is not set, set it to a known value, either
SuperSpeed or SuperSpeedPlus based on the type of controller we are
using. If we are on DWC_usb31 controller, check the PHY interface to see
if it is capable of SuperSpeedPlus.
Also this check is moved after dwc3_core_init() so that we can check
dwc->revision.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Update various places where the speed is checked so that it takes into
account SuperSpeedPlus properly.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Update various registers fields definitions for the DWC_usb31 controller
for SuperSpeedPlus support.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add a convenience function to check if the controller is DWC_usb31.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The check for < 0 is impossible now that
of_clk_get_parent_count() returns an unsigned int. Simplify the
code and update the types.
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The assignement of EP transfer resources was not handled properly in the
dwc3 driver. Commit aebda61871 ("usb: dwc3: Reset the transfer
resource index on SET_INTERFACE") previously fixed one aspect of this
where resources may be exhausted with multiple calls to SET_INTERFACE.
However, it introduced an issue where composite devices with multiple
interfaces can be assigned the same transfer resources for different
endpoints. This patch solves both issues.
The assignment of transfer resources cannot perfectly follow the data
book due to the fact that the controller driver does not have all
knowledge of the configuration in advance. It is given this information
piecemeal by the composite gadget framework after every
SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook
programming model in this scenario can cause errors. For two reasons:
1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and
SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple
interfaces.
2) The databook does not mention doing more DEPXFERCFG for new endpoint
on alt setting (8.1.6).
The following simplified method is used instead:
All hardware endpoints can be assigned a transfer resource and this
setting will stay persistent until either a core reset or hibernation.
So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for
every hardware endpoint as well. We are guaranteed that there are as
many transfer resources as endpoints.
This patch triggers off of the calling dwc3_gadget_start_config() for
EP0-out, which always happens first, and which should only happen in one
of the above conditions.
Fixes: aebda61871 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE")
Cc: <stable@vger.kernel.org> # v3.2+
Reported-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch is needed in order to pass one test case
defined in the OTG Automated Compliance Test specification.
Specification location:
http://www.usb.org/developers/onthego/otgeh_compliance_plan_1_2.pdf
This test case uses PET Tool, and PET Tool is one USB hardware
equipment provided by MQP Electronics.
Test case id is 6.8.3 B-UUT Bypass Capacitance.
We must set this otg flag in order to be able to return OTG
descriptor during enumeration, otherwise this test case with
failed with below error: "Get OTG descriptor request stalled".
Signed-off-by: Jianqiang Tang <jianqiang.tang@intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
if we have a !PM kernel build, our runtime
suspend/resume callbacks will be left defined but
unused. Add a ifdef CONFIG_PM guard.
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the request->length is zero, a ZLP should already be sent due to that
and another ZLP is not needed to terminate the transfer.
Fixes: 04c03d10e5 ("usb: dwc3: gadget: handle request->zero")
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
struct usb_request have 3 flags which might be
important to know about during debug. This patch
shows each of the 3 flags as a single letter:
z -> for zero
s -> short not okay
i -> interrupt
A capital letter means the feature is enabled
while a lower case letter means it is disabled;
Thus 'zsI' indicates that a ZLP is not needed,
that we can accept a short packet and interrupt
for this request should be enabled.
Signed-off-by: Felipe Balbi <balbi@ti.com>
So far, dwc3 has always missed request->zero
handling for every endpoint. Let's implement
that so we can handle cases where transfer must
be finished with a ZLP.
Note that dwc3 is a little special. Even though
we're dealing with a ZLP, we still need a buffer
of wMaxPacketSize bytes; to hide that detail from
every gadget driver, we have a preallocated buffer
of 1024 bytes (biggest bulk size) to use (and
share) among all endpoints.
Reported-by: Ravi B <ravibabu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now that we have a generic dwc3-of-simple.c, we can
use that instead of maintaining dwc3-qcom.c which is
extremely similar.
Cc: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For simple platforms which merely enable some clocks
and populate its children, we can use this generic
glue layer to avoid boilerplate code duplication.
For now this supports Qcom and Xilinx, but if we
find a way to add generic handling of regulators and
optional PHYs, we can absorb exynos as well.
Tested-by: Subbaraya Sundeep Bhatta <subbaraya.sundeep.bhatta@xilinx.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It just ocurred to me that dwc3 already gives a
really hint of when a setup packet is pending and
that's the SETUP_PENDING TRB Status for EP0 IRQs.
Fix setup_packet_pending initialization based on
that. While at that, also make sure the comment in
gadget.c matches what code is doing.
Signed-off-by: Felipe Balbi <balbi@ti.com>
In dwc3_cleanup_done_reqs() we expect that all
iterations of our while (1) loop will find a valid
struct dwc3_request *. In case we don't, we're
dumping a WARN_ON_ONCE() splat so that people report
the failure.
This patch is a simple cleanup converting:
if (!req) {
WARN_ON_ONCE(1);
return 1;
}
to:
if (WARN_ON_ONCE(!req))
return 1;
which is a little easier to read.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The last few dev_dbg() messages are converted to
tracepoints and we can finally ignore dev_dbg()
messages during debug sessions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The last few dev_dbg() messages are converted to
tracepoints and we can finally ignore dev_dbg()
messages during debug sessions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The last few dev_dbg() messages are converted to
tracepoints and we can finally ignore dev_dbg()
messages during debug sessions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
By moving our sanity checks our internal function
__dwc3_gadget_ep_queue() we can simplify the
externally visible API while also making sure that
callers of __dwc3_gadget_ep_queue() also make use of
the same checks.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Because interrupt endpoints usually transmit such
small amounts of data, it seems pointless to prestart
transfers and try to get speed improvements. This
patch also sorts out a problem with CDC ECM function
where its notification endpoint gets stuck in busy
state and we continuously issue Update Transfer
commands.
Fixes: 8a1a9c9e45 ("usb: dwc3: gadget: start transfer on XFER_COMPLETE")
Signed-off-by: Felipe Balbi <balbi@ti.com>
In some SoCs, dwc3 is implemented as a USB2.0 only
core, meaning that it can't ever achieve SuperSpeed.
Currect driver always sets gadget.max_speed to
USB_SPEED_SUPER unconditionally. This can causes
issues to some Host stacks where the host will issue
a GetBOS() request and we will reply with a BOS
containing Superspeed Capability Descriptor.
At least Windows seems to be upset by this fact and
prints a warning that we should connect $this device
to another port.
[ balbi@ti.com : rewrote entire commit, including
source code comment to make a lot clearer what the
problem is ]
Cc: <stable@vger.kernel.org>
Signed-off-by: Ben McCauley <ben.mccauley@garmin.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 8f2c9544ab.
As it breaks g_ether on my Baytrail FFRD8 device. Everything starts out
fine, but after a bit of data has been transferred it just stops
flowing.
Note that I do get a bunch of these "NOHZ: local_softirq_pending 08"
when booting the machine, but I'm not really sure if they're related
to this problem.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 70f3a9caa1.
That commit was causing a lockdep splat with g_ether and that
was interfering with proper functionality.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Certain Synopsys prototyping PHY boards are not able to meet timings
constraints for LPM. This allows the PHY to meet those timings by
leaving the PHY clock running during suspend.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add a quirk to clear the GUSB2PHYCFG.ENBLSLPM bit, which controls
whether the PHY receives the suspend signal from the controller.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add platform data and set usb3_lpm_capable and has_lpm_erratum.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the alignment of the PCI device definitions. Also change the hex
digit capitalization of one constant to make it consistent with the
rest of the file and driver.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch allows the dwc3 driver to run on the new Synopsys USB 3.1
IP core, albeit in USB 3.0 mode only.
The Synopsys USB 3.1 IP (DWC_usb31) retains mostly the same register
interface and programming model as the existing USB 3.0 controller IP
(DWC_usb3). However the GSNPSID and version numbers are different.
Add checking for the new ID to pass driver probe.
Also, since the DWC_usb31 version number is lower in value than the
full GSNPSID of the DWC_usb3 IP, we set the high bit to identify
DWC_usb31 and to ensure the values are higher.
Finally, add a documentation note about the revision numbering scheme.
Any future revision checks (for STARS, workarounds, and new features)
should take into consideration how it applies to both the 3.1/3.0 IP.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This adds the PCI product ID for the Synopsys USB 3.1 IP core
(DWC_usb31) on a HAPS-based PCI development platform.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This ID is for the Synopsys DWC_usb3 core with AXI interface on PCIe
HAPS platform. This core has the debug registers mapped at a separate
BAR in order to support enhanced hibernation.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We *know* our threads executes with our IRQs
disabled. We really don't need to use the _irqsave()
variant of spin_lock().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of limiting __dwc3_gadget_kick_transfer() to
Xfer Complete, we can try to issue Update Transfer
command from Xfer In Progress too.
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we get a Xfer Not Ready event with reason
"Transfer Active" it means endpoint is still
transferring data and we can use that to issue
update transfer for this particular endpoint
in case we have pending requests in our queue.
Signed-off-by: Felipe Balbi <balbi@ti.com>
if by the time we get to XFER_COMPLETE we have
pending requests to be processed, instead of waiting
for a following XFER_NOT_READY, let's start the request
right away and, maybe, save the time of a few NAKs
due to lack of started transfers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sharing the ACPI companion with dwc3 core so it has access
to the properties defined for DWC3 in ACPI tables.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
No functional affect on existing platforms, but the driver
is now ready to extract the properties also from ACPI tables
as well as from DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
of_usb_get_dr_mode will be converted into more generic
usb_get_dr_mode function that will take struct device
instead of struct device_node as its parameter.
To make the conversion possible later, waiting for the
platform device for dwc3 to be populated before calling
of_usb_get_dr_mode.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
CC: Giuseppe Cavallaro <peppe.cavallaro@st.com>
CC: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for USB DRVVBUS pinctrl state change during
suspend/resume. This helps is conserving power during
system sleep.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add adjust_frame_length_quirk for writing to fladj register
which adjusts (micro)frame length to value provided by
"snps,quirk-frame-length-adjustment" property thus avoiding
USB 2.0 devices to time-out over a longer run
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We shouldn't return -EBUSY, that's used only internally
when the core still has transfers in flight on a given
endpoint.
Also, combine the error reporting so that we don't have
to duplicate it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of clearing DWC3_PENDING_REQUEST when
we start transfer, let's do it when the request
is actually queued, that way we know for sure
that we're clearing in the right time.
Signed-off-by: Felipe Balbi <balbi@ti.com>
In an attempt to make dwc3 slightly faster, let's
start usb_requests as soon as they come as that will
let us avoid a XFER_NOT_READY event and save a little
bit of time.
Signed-off-by: Felipe Balbi <balbi@ti.com>
by moving trace_dwc3_ep_queue() from dwc3_gadget_ep_queue()
to __dwc3_gadget_ep_queue() after usb_request is properly
initialized, makes for a better output always showing a
request with 0 actual and -115 (-EINPROGRESS) status.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using spin_lock() in hard irq handler is pointless
and causes a BUG() in RT (real-time) configuration
so get rid of it.
The reason it's pointless is because the driver is
basically accessing register which is, anyways,
atomic.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we enable IRQs before requesting our
extcon device, we might fall into a situation
where and IRQ fires before we're ready to
handle it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use chained TRB mechanism to handle non maxpacket aligned transfers
greater than bounce buffer size. With this the first TRB will be programmed
to receive 'ALIGN(ur->length - maxp, maxp)' data and the second TRB
will be programmed to receive the remaining data using bounce buffer.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add chained TRB support to ep0. Now TRB's can be chained just by
invoking _dwc3_ep0_start_trans_ with 'chain' parameter set to true.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
No functional change. Added a new parameter in _dwc3_ep0_start_trans_ to
indicate whether the TRB is a chained TRB or last TRB. This is in
preparation for adding chained TRB support for ep0.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
No functional change. This is in preparation for handling non maxpacket
aligned transfers greater than bounce buffer size. This is basically to
avoid code duplication when using chained TRB transfers to handle
non maxpacket aligned transfers greater than bounce buffer size.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
No functional change. Used _roundup_ macro to calculate the transfer
size aligned to maxpacket in dwc3_ep0_complete_data. It also makes it
similar to how transfer size is calculated in __dwc3_ep0_do_control_data.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 uses bounce buffer to handle non max packet aligned OUT transfers and
the size of bounce buffer is 512 bytes. However if the host initiates OUT
transfers of size more than 512 bytes (and non max packet aligned), the
driver throws a WARN dump but still programs the TRB to receive more than
512 bytes. This will cause bounce buffer to overflow and corrupt the
adjacent memory locations which can be fatal.
Fix it by programming the TRB to receive a maximum of DWC3_EP0_BOUNCE_SIZE
(512) bytes.
Cc: <stable@vger.kernel.org> # 3.4+
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We have a "Enabling %s" trace when enabling an endpoint
but that message felt lonely without a matching
"Disabling %s". Add it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
When a SoC supports both PHY interfaces but
doesn't define HSPHY in DT/pdata, we will get
an unnecessary dev_warn() which can mislead users
into thinking that they're missing something.
Instead, let's just silently rely on a correct
default. If the HW default is wrong, then HSPHY
is required and USB won't work, this will be
motivation enough for engineers to patch their
way into a working setup.
Reported-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Use this additional parameter and the _optional variant to simplify the
driver and improve error handling. Also expand the comment to explain
why it's not sensible to switch to devm_gpiod_get and why the gpiod_put
is also necessary.
Furthermore this is one caller less that stops us making the flags
argument to gpiod_get*() mandatory.
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes the deprecated notifier API of extcon framwork
and then use the new extcon API with the unique id to indicate
the each external connector (USB, USB-HOST).
Alter deprecated API as following:
- extcon_register_interest() -> extcon_register_notifier()
- extcon_get_cable_state(*edev, char *) -> extcon_get_cable_state_(*edev, id)
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
now that we have no users of dev_dbg() in dwc3,
we can safely remove CONFIG_USB_DWC3_DEBUG.
If dev_dbg() is ever strictly necessary - and I
don't see why it would, considering we want to
rely on tracepoints for debug - we will depend
on DYNAMIC_PRINTK to enable such messages.
Signed-off-by: Felipe Balbi <balbi@ti.com>
the mode of operation is exposed through debugfs
at all times. Because of that, we're removing
the unnecessary messages.
Signed-off-by: Felipe Balbi <balbi@ti.com>
those two messages are informing that the clock
doesn't exist; that, however, is a valid situation
and driver continues just fine by ignoring the error.
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
that message is informing that the clock is missing.
However, that's a valid condition for some setups; driver
even ignores the error and continues just fine.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This fixes an issue introduced in commit b23c843992 (usb: dwc3:
gadget: fix DEPSTARTCFG for non-EP0 EPs) that made sure we would
only use DEPSTARTCFG once per SetConfig.
The trick is that we should use one DEPSTARTCFG per SetConfig *OR*
SetInterface. SetInterface was completely missed from the original
patch.
This problem became aparent after commit 76e838c9f7 (usb: dwc3:
gadget: return error if command sent to DEPCMD register fails)
added checking of the return status of device endpoint commands.
'Set Endpoint Transfer Resource' command was caught failing
occasionally. This is because the Transfer Resource
Index was not getting reset during a SET_INTERFACE request.
Finally, to fix the issue, was we have to do is make sure that
our start_config_issued flag gets reset whenever we receive a
SetInterface request.
To verify the problem (and its fix), all we have to do is run
test 9 from testusb with 'testusb -t 9 -s 2048 -a -c 5000'.
Tested-by: Huang Rui <ray.huang@amd.com>
Tested-by: Subbaraya Sundeep Bhatta <subbaraya.sundeep.bhatta@xilinx.com>
Fixes: b23c843992 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs)
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 3e10a2ce98 ("usb: dwc3: add hsphy_interface
property") introduced a possible NULL pointer
dereference because dwc->hsphy_interface can be
NULL.
In order to fix it, all we have to do is guard
strncmp() against a NULL argument.
Fixes: 3e10a2ce98 ("usb: dwc3: add hsphy_interface property")
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The USB_DWC3_ULPI Kconfig entry uses a UTF-8 non-breaking space (0xca20)
instead of a regular ASCII space (0x20). Commit 2e0d737fc7 ("kconfig:
don't silently ignore unhandled characters") exposes this by warning
about unhandled characters.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves a merge issue in musb_core.c and we want the fixes that
were in Linus's tree in this branch as well for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- dwc2 adds hibernation support
- preparation for sunxi glue to musb driver
- new ULPI bus
- new ULPI PHY driver for TUSB1210
- musb patches to support multiple DMA engines on same binary
- support for R-Car E2 on renesas_usbhs
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Jqzf
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.2 merge window
- dwc2 adds hibernation support
- preparation for sunxi glue to musb driver
- new ULPI bus
- new ULPI PHY driver for TUSB1210
- musb patches to support multiple DMA engines on same binary
- support for R-Car E2 on renesas_usbhs
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case of non-Isochronous transfers, we don't
want to clear DWC3_EP_BUSY flag until XferComplete
event. That's because XferInProgress was only enabled
so we can recycle TRBs and usb_requests quicker, but
there are still other pending requests being transferred.
In order to make sure we don't allow for another StartTransfer
command while the HW is still processing other transfers,
we must keep DWC3_EP_BUSY flag set and this what this patch
does.
Fixes: f3af36511e (usb: dwc3: gadget: always enable IOC on
bulk/interrupt transfers)
Cc: <stable@vger.kernel.org> # v3.15+
Reported-by: sundeep subbaraya <sundeep.lkml@gmail.com>
Tested-by: sundeep subbaraya <sundeep.lkml@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need to return error to caller if command is not sent to
controller succesfully.
Signed-off-by: Subbaraya Sundeep Bhatta <sbhatta@xilinx.com>
Fixes: 72246da40f (usb: Introduce DesignWare USB3 DRD Driver)
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need to return error to caller if command is not sent to
controller succesfully.
Signed-off-by: Subbaraya Sundeep Bhatta <sbhatta@xilinx.com>
Fixes: b09bb64239 (usb: dwc3: gadget: implement Global Command support)
Cc: <stable@vger.kernel.org> #v3.5+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Registers DWC3's ULPI interface with the ULPI bus when it's
available.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On some BYT platforms the USB2 PHY needs to be put into
operational mode by the controller driver with GPIOs
controlling the PHYs reset and cs signals.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Platforms that have configured DWC_USB3_HSPHY_INTERFACE with
value 3, i.e. UTMI+ and ULPI, need to inform the driver of
the actual HSPHY interface type with the property. "utmi" if
the interface is UTMI+ or "ulpi" if the interface is ULPI.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This allows dwc3_phy_setup() to be more useful later. There
is nothing preventing the PHY configuration registers from
being programmed early. They do not loose their context in
soft reset.
There are however other PHY related operations that should
be executed before the driver request handles to the PHYs,
such as registering DWC3's ULPI interface, which can now be
done in dwc3_phy_setup().
Also, if there ever was need for the two 100ms delays in
dwc3_phy_setup() there isn't anymore. The PHYs are now reset
after the PHY interfaces are setup.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So it can be called from other places later.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So they are available when ULPI interface support is added.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need to store it before phys are handled, so we can later
use it in ULPI interface support code.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make selection between ULPI and UTMI+ interfaces possible by
providing definition for the bit in Global USB2 PHY
Configuration Register that controls it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Definitions for Global USB2 PHY Vendor Control Register
bits. We will need them to access ULPI PHY registers later.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The macros related to register UTMI_OTG_CTRL and UTMI_OTG_STATUS are
swapped. Correct them for readability.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes "Enable USB3 LPM Capability" option from Kconfig
and adds snps,usb3_lpm_capable devicetree property instead of it.
USB3 LPM (Link Power Management) capability is hardware property, and
it's platform dependent, so if our hardware supports this feature, we
want rather to configure it in devicetree than having it as Kconfig option.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Removed FIXME from usb/dwc3/dwc3-pci.c by moving definition of
PCI_VENDOR_ID_SYNOPSYS shared with usb/dwc2 to linux/pci_ids.h.
Signed-off-by: Joseph Kogut <joseph.kogut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now that we're using XFERINPROGRESS for all endpoint
types (except Control), we will *always* be completing
one TRB at a time, so it's safe to remove the loop
from dwc3_cleanup_done_reqs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes a bug where removing dwc3-omap.ko
would not trigger removal of dwc3.ko.
of_platform_depopulate() already bakes an easy to
use API for removing all our children which were
populated during probe(); Let's use that one instead
of cooking our own solution.
Note that this is kind of a revert of commit c5a1fbc
(usb: dwc3: dwc3-omap: Fix the crash on module removal)
although we can't simply revert that because a direct
call to platform_device_unregister would also be flakey.
Signed-off-by: Felipe Balbi <balbi@ti.com>
That trick is only needed if we end up with an error, so
there's no point in messing that outside of an error path.
In fact doing so causes problems when removing dwc3.ko,
problems which commit c5a1fbc (usb: dwc3: dwc3-omap: Fix
the crash on module removal) mistakenly tried to fix.
Signed-off-by: Felipe Balbi <balbi@ti.com>
In the wrapper the IRQ disable should be done by writing 1's to the
IRQ*_CLR register. Existing code is broken because it instead writes
zeros to IRQ*_SET register.
Fix this by adding functions dwc3_omap_write_irqmisc_clr() and
dwc3_omap_write_irq0_clr() which do the right thing.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 8e74475b0e (usb: dwc3: gadget: use udc-core's
reset notifier) added support for the new UDC core's
reset notifier to dwc3 but while at it, it removed
a spin_lock() from dwc3_reset_gadget() which might
cause an unbalanced spin_unlock() further down the line
Fixes: 8e74475b0e (usb: dwc3: gadget: use udc-core's reset notifier)
Cc: <stable@vger.kernel.org> # v3.19
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sometimes we want to just print a formatted
string without passing any extra data. The
following will be used for removing reliance
on dev_vdbg() from dwc3.
Signed-off-by: Felipe Balbi <balbi@ti.com>
if an unknown IRQ event is triggered, that means
the HW is really misbehaving. Instead of printing
a debug message, let's WARN() so users report
when that happens.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Removing a few items that are not needed anymore and
adding separate function for quirks.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is nothing specific being done in the suspend and
resume callbacks that is not already taken care of in PCI
driver core, so dropping the functions.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
None of the PCI platforms need the NOP transceivers, and
since we can now live without the PHYs, removing
registration of the platform devices for them.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 gadget sets up a pool of 32 TRBs for each EP during initialization. This
means, the max TRBs that can be submitted for an EP is fixed to 32. Since the
request queue for an EP is a linked list, any number of requests can be queued
to it by the gadget layer. However, the dwc3 driver must not submit TRBs more
than the pool it has created for. This limit wasn't respected when SG was used
resulting in submitting more than the max TRBs, eventually leading to
non-transfer of the TRBs submitted over the max limit.
Root cause:
When SG is used, there are two loops iterating to prepare TRBs:
- Outer loop over the request_list
- Inner loop over the SG list
The code was missing break to get out of the outer loop.
Fixes: eeb720fb21 (usb: dwc3: gadget: add support for SG lists)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When scatter gather (SG) is used, multiple TRBs are prepared from one DWC3
request (dwc3_request). So while preparing TRBs, the 'last' flag should be set
only when it is the last TRB being prepared from the last dwc3_request entry.
The current implementation uses list_is_last to check if the dwc3_request is the
last entry from the request_list. However, list_is_last returns false for the
last entry too. This is because, while preparing the first TRB from a request,
the function dwc3_prepare_one_trb modifies the request's next and prev pointers
while moving the URB to req_queued. Hence, list_is_last always returns false no
matter what.
The correct way is not to access the modified pointers of dwc3_request but to
use list_empty macro instead.
Fixes: e5ba5ec833 (usb: dwc3: gadget: fix scatter gather implementation)
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc3_gadget_init_hw_endpoints calls dwc3_alloc_trb_pool only if epnum is not
equal to 0 or 1. Hence, rechecking it in the called function is redundant.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
of non-dt boot. Adds three new PHY drivers using the PHY framework and some
miscellaneous fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=oo3u
-----END PGP SIGNATURE-----
Merge tag 'for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-testing
Kishon writes:
Improvements in phy-core specifically on PHY core finds the PHY in the case
of non-dt boot. Adds three new PHY drivers using the PHY framework and some
miscellaneous fixes and cleanups.
Copy-paste error from the previous block of error handling code.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,e1;
@@
if (IS_ERR(e)) {
...
(
ret = PTR_ERR(e);
|
* ret = PTR_ERR(e1);
)
...
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On some platforms a PHY may need to be handled also in the
host controller driver. Exynos5420 SoC requires some "PHY
tuning" based on the USB speed. This patch delivers dwc3's
PHYs to the xhci platform device when it's created.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
DWC3 controller on Exynos7 SoC has separate control for
AXI UpScaler which connects DWC3 DRD controller to AXI bus.
Get the gate clock for the same to control it across power
cycles.
Suggested-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 controller on Exynos SoC series have separate control for
suspend clock which replaces pipe3_rx_pclk as clock source to
a small part of DWC3 core that operates when SS PHY is in its
lowest power state (P3) in states SS.disabled and U3.
Suggested-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There's no need to keep one local variable for clock, and
then assign the same to 'clk' member of dwc3_exynos.
Just cleaning it up.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There was another instance where we were
holding pointers which could be long gone.
Fix that by caching only values pointed to
by such pointer.
Because no crash has been observed, this patch
will be sent on v3.19 merge window, instead of
-rc.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 6856d30 (usb: dwc3: ep0: return early
on NULL requests) tried to fix a minor corner
case where we could dereference a NULL pointer
but it also ended up introducing some dead code.
Unfortunately, that dead code, if reached, could
end up starving the endpoint request list because
a request would never be given back when it should.
Fix this by moving the check for empty request list
before its first use.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
as it turns out, at least AM437x silicon (non-FPGA)
needs to enable PHY suspend quirk. So let's allow
for PHY suspend quirk to be used with non-FPGA
builds too.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the following checkpatch warning.
WARNING: break is not useful after a goto or return
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 Exynos Specific Glue layer can be used only for Exynos SoCs.
In addition, non-DT for EXYNOS SoCs is not supported from v3.11;
thus, there is no need to support non-DT for DWC3 Exynos Specific
Glue layer.
The 'linux/platform_data/dwc3-exynos.h' file has been used for
non-DT support. Thus, the 'dwc3-exynos.h' file is removed, because
it is not used anymore.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
HIRD threshold should be configurable by different platforms.
From DesignWare databook:
When HIRD_Threshold[4] is set to 1b1 and HIRD value is greater than or
equal to the value in HIRD_Threshold[3:0], dwc3 asserts output signals
utmi_l1_suspend_n to put PHY into Deep Low-Power mode in L1.
When HIRD_Threshold[4] is set to 1b0 or the HIRD value is less than
HIRD_Threshold[3:0], dwc3 asserts output signals utmi_sleep_n on L1.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds support for AMD Nolan (NL) FPGA and SoC platform.
Cc: Jason Chang <jason.chang@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disable usb2 suspend phy quirk, and some special platforms
can configure that if it is needed.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disable usb3 suspend phy quirk, and some special platforms
can configure that if it is needed.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds Tx de-emphasis quirk, and the Tx de-emphasis value is
configurable according to PIPE3 specification.
Value Description
0 -6dB de-emphasis
1 -3.5dB de-emphasis
2 No de-emphasis
3 Reserved
It can be configured on DT or platform data.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It is recommended to set USB3 and USB2 SUSPHY bits to '1' after the core
initialization is completed above the dwc3 revision 1.94a.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds RX_DETECT to Polling.LFPS control quirk, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds LFPS filter quirk, and some special platforms can configure
that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds delay PHY power change from P0 to P1/P2/P3 when link state
changing from U0 to U1/U2/U3 respectively, and some special platforms can
configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds delay P0 to P1/P2/P3 quirk for U2/U2/U3, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds request P1/P2/P3 quirk for U2/U2/U3, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds P3 in U2 SS inactive quirk, and some special platforms can
configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds u2exit lfps quirk, and some special platforms can configure
that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When parameter DWC_USB3_LPM_ERRATA_ENABLE is enabled in Andvanced
Configuration of coreConsultant, it supports of xHCI BESL Errata Dated
10/19/2011 is enabled in host mode. In device mode it adds the capability
to send NYET response threshold based on the BESL value received in the LPM
token, and the threhold is configurable for each soc platform.
This patch adds an entry that soc platform is able to define the lpm
capacity with their own device tree or bus glue layer.
[ balbi@ti.com : added devicetree documentation, spelled threshold
completely, made sure threshold is only applied to
proper core revisions. ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disscramble quirk, and it only needs to be enabled at fpga
board on some vendor platforms.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch initializes platform data at pci glue layer, and SoCs x86-based
platform vendor is able to define their flags in platform data at bus glue
layer. Then do some independent behaviors at dwc3 core level.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some chip vendor is on pre-silicon phase, which needs to use the simulation
board. It should have the same product and vendor id with the true soc, but
might have some minor different configurations.
Below thread discussion proposes to find a method to distinguish between
simulation board and soc.
http://marc.info/?l=linux-usb&m=141194772206369&w=2
In Andvanced Configuration of coreConsultant, there is the parameter of
DWC_USB_EN_FPGA. This bit has the function we need. And it would response as 7
bit of GHWPARAMS6 register. So it's able to check this functional bit to confirm
if works on FPGA board.
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It enables hibernation if the function is set in coreConsultant.
Suggested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sanity check on resource happening with devm_ioremap_resource().
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
now that no UDC driver relies on the extra
'driver' argument to ->udc_stop(), we can
safely remove it.
This commit is based on previous work by
Robert Baldyga <r.baldyga@samsung.com> which
can be found at [1]; however that patch turned
out to have a high probability of regressing
many UDC drivers because of a blind search & replace
s/driver/$udc->driver/ which caused the 'driver'
argument to stop_activity() to be a valid non-NULL
pointer when it should be NULL, thus causing UDCs
to mistakenly call gadget driver's ->disconnect()
callback.
[1] http://markmail.org/message/x5zneg4xea4zntab
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some gadget/function drivers might want to do
improper request recycling by allocating a single
request from one particular endpoint and queueing
it to another completely unrelated endpoint.
One such case was found with f_loopback.c.
To prevent such cases from happening again, let's
WARN() so we get a loud enough failure and persuade
users to report errors.
Signed-off-by: Felipe Balbi <balbi@ti.com>
whenever we get a Disconnect Interrupt, we should
make sure to update out udc state to NOT_ATTACHED,
otherwise sysfs will show wrong values.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using ->prepare()/->complete() to mask/unmask
IRQs is wrong at least for dwc3. We need to
make sure that by the end of ->resume(), IRQs
are working and ready to fire because a child
device may need working IRQs for its own ->resume()
method.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Enabling the core interrupts in complete is too late for
XHCI, and stops it from proper operation. The root of the
problem is due to a disagreement between dwc3-omap and XHCI
about when IRQs should be enabled.
As it turns out, ->resume's documentation states that:
"... generally the driver is expected to start working
again, responding to hardware events and software requests
(the device itself may be left in a low-power state, waiting
for a runtime resume to occur) ..."
From that we infer that IRQs must be unmasked by the end of
->resume().
Due to that, we will remove ->prepare() and ->complete() and
disable/enable interrupts in ->suspend()/->resume().
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the probe drivers have already set the dma_mask, not
replacing the value.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Grygorii Strashko