Interrupt handler checked THRE bit (transmitter holding register
empty) in LSR to detect if TX fifo is empty.
In case when there is only receive interrupts the TX handling
got called because THRE bit in LSR is set when there is no
transmission (FIFO empty). TX handling caused TX stop, which in
RS-485 half-duplex mode actually resets receiver FIFO. This is not
desired during reception because of possible data loss.
The fix is to check if THRI is set in IER in addition of the TX
fifo status. THRI in IER is set when TX is started and cleared
when TX is stopped.
This ensures that TX handling is only called when there is really
transmission on going and an interrupt for THRE and not when there
are only RX interrupts.
Signed-off-by: Kimmo Rautkoski <ext-kimmo.rautkoski@vaisala.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove spin_lock_irqsave in stm32_config_rs485, it cause recursive locking.
Already locked in uart_set_rs485_config.
Fixes: 1bcda09d29 ("serial: stm32: add support for RS485 hardware control mode")
Signed-off-by: Borut Seljak <borut.seljak@t-2.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Deferred probe is an expected return value for clk_get() on many
platforms. The driver deals with it properly, so there's no need
to output a warning that may potentially confuse users.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_info() is more appropriate for printing messages inside drivers, so
switch to dev_info().
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_info() is more appropriate for printing messages inside drivers, so
switch to dev_info().
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to support Rx in-band wakeup, we need to enable irq wake on an
edge sensitive interrupt of Rx pin before suspend and disable it when
resuming.
This interrupt is used only as wake source to resume the system when
suspended. Note that the sent character will be lost as the controller is
actually suspended.
We use this to support wakeup on bluetooth. Bluetooth will repeatedly send
0xFD to wakeup host. Once host detects Rx falling, an interrupt is
triggered, and the system leaves sleep state. Then, the bluetooth driver
will send 0xFC to bluetooth and bluetooth can start to send normal HCI
packets.
Signed-off-by: Claire Chang <tientzu@chromium.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the cable is not connected then the target gets into
an infinite wait for tx empty.
Add a timeout to the tx empty wait.
Reported-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we are doing a read of the status register.
Move the spinlock after that as the reads need not be spinlock
protected. This patch prevents relaxing the cpu with spinlock held.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When modprobe/rmmod/modprobe module, if platform_driver_register() fails,
the kernel complained,
proc_dir_entry 'driver/digicolor-usart' already registered
WARNING: CPU: 1 PID: 5636 at fs/proc/generic.c:360 proc_register+0x19d/0x270
Fix this by adding uart_unregister_driver() when platform_driver_register() fails.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix sparse warning:
drivers/tty/serial/stm32-usart.c:603:14: warning:
symbol 'stm32_get_databits' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Select either pinctrl sleep state in suspend function or default state in
resume function.
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 84ecc2f6eb.
con_insert_unipair() is working with a sparse 3-dimensional array:
- p->uni_pgdir[] is the top layer
- p1 points to a middle layer
- p2 points to a bottom layer
If it needs to allocate a new middle layer, and then fails to allocate
a new bottom layer, it would previously free only p2, and now it frees
both p1 and p2. But since the new middle layer was already registered
in the top layer, it was not leaked.
However, if it looks up an *existing* middle layer and then fails to
allocate a bottom layer, it now frees both p1 and p2 but does *not*
free any other bottom layers under p1. So it *introduces* a memory
leak.
The error path also cleared the wrong index in p->uni_pgdir[],
introducing a use-after-free.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 84ecc2f6eb ("consolemap: Fix a memory leaking bug in drivers/tty/vt/consolemap.c")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As suggested by Uwe, add a note indicating that the modem control
signals do not support interrupts, which precludes the driver from
using mctrl_gpio_init().
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Add support for the generic mctrl gpio helper. This will allow us to
convert several board files to use the gpiod tables to assign GPIOs to
serial ports, rather than needing to have private function callbacks.
If the generic mctrl gpio helper fails, ignore the mctrl gpios rather
than preventing the (possibly console) serial port from being created.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
After memory allocation failure vc_allocate() doesn't clean up data
which has been initialized in visual_init(). In case of fbcon this
leads to divide-by-0 in fbcon_init() on next open of the same tty.
memory allocation in vc_allocate() may fail here:
1097: vc->vc_screenbuf = kzalloc(vc->vc_screenbuf_size, GFP_KERNEL);
on next open() fbcon_init() skips vc_font.data initialization:
1088: if (!p->fontdata) {
division by zero in fbcon_init() happens here:
1149: new_cols /= vc->vc_font.width;
Additional check is needed in fbcon_deinit() to prevent
usage of uninitialized vc_screenbuf:
1251: if (vc->vc_hi_font_mask && vc->vc_screenbuf)
1252: set_vc_hi_font(vc, false);
Crash:
#6 [ffffc90001eafa60] divide_error at ffffffff81a00be4
[exception RIP: fbcon_init+463]
RIP: ffffffff814b860f RSP: ffffc90001eafb18 RFLAGS: 00010246
...
#7 [ffffc90001eafb60] visual_init at ffffffff8154c36e
#8 [ffffc90001eafb80] vc_allocate at ffffffff8154f53c
#9 [ffffc90001eafbc8] con_install at ffffffff8154f624
...
Signed-off-by: Grzegorz Halat <ghalat@redhat.com>
Reviewed-by: Oleksandr Natalenko <oleksandr@redhat.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the RELEVANT_IFLAG() macro which hasn't been used at least since
the dawn of git.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_lookup_driver take a reference to the struct tty_driver, but forget
to release it on the error path, lead to a memory leak.
add a tty_driver_kref_put before error return.
Signed-off-by: Lin Yi <teroincn@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After memory allocation failure vc_allocate() doesn't clean up data
which has been initialized in visual_init(). In case of fbcon this
leads to divide-by-0 in fbcon_init() on next open of the same tty.
memory allocation in vc_allocate() may fail here:
1097: vc->vc_screenbuf = kzalloc(vc->vc_screenbuf_size, GFP_KERNEL);
on next open() fbcon_init() skips vc_font.data initialization:
1088: if (!p->fontdata) {
division by zero in fbcon_init() happens here:
1149: new_cols /= vc->vc_font.width;
Additional check is needed in fbcon_deinit() to prevent
usage of uninitialized vc_screenbuf:
1251: if (vc->vc_hi_font_mask && vc->vc_screenbuf)
1252: set_vc_hi_font(vc, false);
Crash:
#6 [ffffc90001eafa60] divide_error at ffffffff81a00be4
[exception RIP: fbcon_init+463]
RIP: ffffffff814b860f RSP: ffffc90001eafb18 RFLAGS: 00010246
...
#7 [ffffc90001eafb60] visual_init at ffffffff8154c36e
#8 [ffffc90001eafb80] vc_allocate at ffffffff8154f53c
#9 [ffffc90001eafbc8] con_install at ffffffff8154f624
...
Signed-off-by: Grzegorz Halat <ghalat@redhat.com>
Reviewed-by: Oleksandr Natalenko <oleksandr@redhat.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In function con_insert_unipair(), when allocation for p2 and p1[n]
fails, ENOMEM is returned, but previously allocated p1 is not freed,
remains as leaking memory. Thus we should free p1 as well when this
allocation fails.
Signed-off-by: Gen Zhang <blackgod016574@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SMC relocation can also be activated earlier by the bootloader,
so the driver's behaviour cannot rely on selected kernel config.
When the SMC is relocated, CPM_CR_INIT_TRX cannot be used.
But the only thing CPM_CR_INIT_TRX does is to clear the
rstate and tstate registers, so this can be done manually,
even when SMC is not relocated.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 9ab9212014 ("cpm_uart: fix non-console port startup bug")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checks the returned values of platform_get_irq() for both required
"event" and optional "wakeup" IRQs during probe. This allows the driver
probe to be deferred if needed.
Removes redundant checks for 'cfg.has_wakeup'.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds a check on the Transmission Complete bit status before closing the
com port. Prevents the port closure before the end of the transmission.
TC poll loop is moved from stm32_tx_dma_complete to stm32_shutdown
routine, in order to check TC before shutdown in both dma and
PIO tx modes.
TC clear is added in stm32_transmit_char routine, in order to be cleared
before transmitting in both dma and PIO tx modes.
Fixes: 3489187204 ("serial: stm32: adding dma support")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disables the tx irq when the transmission is ended and updates stop_tx
conditions for code cleanup.
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fixes a rx data error when data length < 8 bits and parity is enabled.
RDR register MSB is used for parity bit reception.
- Adds a mask to ignore MSB when data is get from RDR.
Fixes: 3489187204 ("serial: stm32: adding dma support")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fixes parity and framing error bit by clearing parity and framing error
flag. The current implementation doesn't clear the error bits when an
error is detected.
- Fixes the incorrect name of framing error clearing flag in header file.
- Fixes misalignement between data frame and errors status. The status
read for "n" frame was the status of "n+1" frame".
- Fixes break detection was not triggered by the expected register.
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STM32 supports either:
- 8 and 9 bits word length (including parity bit) for stm32f4 compatible
devices
- 7, 8 and 9 bits word length (including parity bit) for stm32f7 and
stm32h7 compatible devices.
As a consequence STM32 supports the following termios configurations:
- CS7 with parity bit, and CS8 (with or without parity bit) for stm32f4
compatible devices.
- CS6 with parity bit, CS7 and CS8 (with or without parity bit) for
stm32f7 and stm32h7 compatible devices.
This patch is fixing word length by configuring correctly the SoC with
supported configurations.
Fixes: ada8618ff3 ("serial: stm32: adding support for stm32f7")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The datasheet states:
Bit 4: ClockEnSet the ClockEn bit high to enable an external clocking
(crystal or clock generator at XIN). Set the ClockEn bit to 0 to disable
clocking
Bit 1: CrystalEnSet the CrystalEn bit high to enable the crystal
oscillator. When using an external clock source at XIN, CrystalEn must
be set low.
The bit 4, MAX310X_CLKSRC_EXTCLK_BIT, should be set and was not.
This was required to make the MAX3107 with an external crystal on our
board able to send or receive data.
Signed-off-by: Joe Burmeister <joe.burmeister@devtank.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As noted in commit 84b40e3b57 ("serial: 8250: omap: Disable DMA for
console UART"), UART console lines use low-level PIO only access functions
which will conflict with use of the line when DMA is enabled, e.g. when
the console line is also used for systemd messages. So disable DMA
support for UART console lines.
Reported-by: Michael Rodin <mrodin@de.adit-jv.com>
Link: https://patchwork.kernel.org/patch/10929511/
Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each time the DMA engine signals a transaction error the driver prints
a message at error level. Getting transaction errors is pretty much
expected on baudrate mismatches and the correspoding error counters
are increased in this case properly. Remove the error message which
is possibly repeated at a very high rate which can lock up the whole
system.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the tty layer requests the uart to throttle, the current code
executing in msm_serial will trigger "Bad mode in Error Handler" and
generate an invalid stack frame in pstore before rebooting (that is if
pstore is indeed configured: otherwise the user shall just notice a
reboot with no further information dumped to the console).
This patch replaces the PIO byte accessor with the word accessor
already used in PIO mode.
Fixes: 68252424a7 ("tty: serial: msm: Support big-endian CPUs")
Cc: stable@vger.kernel.org
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Batch read mode doesn't check any conditions or flags except the Rx
overflow one. But it may only happen after the last character is pushed
into the RHR register. In this case we shouldn't push all the read
characters with overrun flag set, but only the last one caused the
FIFO overflow. This commit splits the characters retrieval loop into
two parts. First one is ordinary intsert-chars procedure without taking
the overrun status into account. Second part inserts the last character
checking whether the overrun happened and pushing a '\0' character with
TTY_OVERRUN flag to a flip-buffer.
If we left the loop the way it was the '\0' character would be inserted
after each character retrieved at the overrun occasion.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART port might be pre-configured with rs485 enabled flag at the
time of the port starting up process. In this case we need to
have the hardware rs485-related registers initialized in accordance
with the rs485 flags and settings provided by the configs descriptor.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver currently sets the echo suppression bit by default when rs485
is enabled. Naturally it disables any data retrieval in rs485 mode while
RTSn is pushed up. The receiver gate (RX_) can be enabled just by clearing
(or not setting) the EchoSuprs bit of mode2 register. So by setting or
clearing the bit we implement the SER_RS485_RX_DURING_TX rs485 flag
support.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current calculator doesn't do it' job quite correct. First of all the
max310x baud-rates generator supports the divisor being less than 16.
In this case the x2/x4 modes can be used to double or quadruple
the reference frequency. But the current baud-rate setter function
just filters all these modes out by the first condition and setups
these modes only if there is a clocks-baud division remainder. The former
doesn't seem right at all, since enabling the x2/x4 modes causes the line
noise tolerance reduction and should be only used as a last resort to
enable a requested too high baud-rate.
Finally the fraction is supposed to be calculated from D = Fref/(c*baud)
formulae, but not from D % 16, which causes the precision loss. So to speak
the current baud-rate calculator code works well only if the baud perfectly
fits to the uart reference input frequency.
Lets fix the calculator by implementing the algo fully compliant with
the fractional baud-rate generator described in the datasheet:
D = Fref / (c*baud), where c={16,8,4} is the x1/x2/x4 rate mode
respectively, Fref - reference input frequency. The divisor fraction is
calculated from the same formulae, but making sure it is found with a
resolution of 0.0625 (four bits).
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SPI transfer tx/rx buffers must be DMA-safe and the structure
documentation clearly states this. Data declared on the system stack isn't
DMA-safe [1]. Instead at least kernel memory should be used for the
buffers. In order to fix this here we can create the buffers at the device
probing stage and use them without any synchronization, since batch
read/write methods are called from non-reentrant contexts - either from
rx-event IRQ threaded handler or from the tx workqueue item.
[1] Documentation/DMA-API-HOWTO.txt
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_port structure instance is embedded into the max310x_one
super-structure, which is accessed by some of the uart-port callback
methods. In order to improve the callback's code readability lets
define the to_max310x_port() wrapper which just translates the passed
uart_port pointer to the max310x_one one. It is also going to be
handy in future commits.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since cmwq introduction in the kernel, workqueues've been turned into
non-reentrant execution contexts [1]. It means any work item is
guaranteed to be executed by at most one worker system-wide at any
given time. Since tx-handler max310x_handle_tx() is called by a
single work item we don't need it to be self-protected by the mutex.
We also don't need to check the tx work item pending state before
scheduling it (which in the first place was racy btw), since cmwq will
make sure to reschedule the item if it wasn't pending at the moment of
schedule_work() call.
[1] Documentation/core-api/workqueue.rst
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PL011 register space includes all necessary status bits to
determine whether a device instance requires handling in response
to an interrupt. Therefore, multiple instances of the device could
be serviced by a single shared interrupt, which is the case on BCM7211.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev_dbg statement should print the value of uart.port.mapbase instead
of its address. Besides that, uart.port.irq and uart.port.iotype are all
unsigned types, so using %u is more appropriate.
Signed-off-by: Hao Lee <haolee.swjtu@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use of_device_get_match_data() to simplify the code a bit.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch set contains an assortment of RISC-V related patches that I'd
like to target for the 5.2 merge window. Most of the patches are
cleanups, but there are a handful of user-visible changes:
* The nosmp and nr_cpus command-line arguments are now supported, which
work like normal.
* The SBI console no longer installs itself as a preferred console, we
rely on standard mechanisms (/chosen, command-line, hueristics)
instead.
* sfence_remove_sfence_vma{,_asid} now pass their arguments along to the
SBI call.
* Modules now support BUG().
* A missing sfence.vma during boot has been added. This bug only
manifests during boot.
* The arch/riscv support for SiFive's L2 cache controller has been
merged, which should un-block the EDAC framework work.
I've only tested this on QEMU again, as I didn't have time to get things
running on the Unleashed. The latest master from this morning merges in
cleanly and passes the tests as well.
This patch set rebased my "5.2 MW, Part 1" patch set which includes an
erronous empty file. It's also a rebase of my "5.2 MW, Part 2" patch
set, in which I managed to create another file while attempting to
remove the empty file.
Sorry for all the noise!
-----BEGIN PGP SIGNATURE-----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=mZwx
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.2-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Pull RISC-V updates from Palmer Dabbelt:
"This contains an assortment of RISC-V related patches that I'd like to
target for the 5.2 merge window. Most of the patches are cleanups, but
there are a handful of user-visible changes:
- The nosmp and nr_cpus command-line arguments are now supported,
which work like normal.
- The SBI console no longer installs itself as a preferred console,
we rely on standard mechanisms (/chosen, command-line, hueristics)
instead.
- sfence_remove_sfence_vma{,_asid} now pass their arguments along to
the SBI call.
- Modules now support BUG().
- A missing sfence.vma during boot has been added. This bug only
manifests during boot.
- The arch/riscv support for SiFive's L2 cache controller has been
merged, which should un-block the EDAC framework work.
I've only tested this on QEMU again, as I didn't have time to get
things running on the Unleashed. The latest master from this morning
merges in cleanly and passes the tests as well"
* tag 'riscv-for-linus-5.2-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux: (31 commits)
riscv: fix locking violation in page fault handler
RISC-V: sifive_l2_cache: Add L2 cache controller driver for SiFive SoCs
RISC-V: Add DT documentation for SiFive L2 Cache Controller
RISC-V: Avoid using invalid intermediate translations
riscv: Support BUG() in kernel module
riscv: Add the support for c.ebreak check in is_valid_bugaddr()
riscv: support trap-based WARN()
riscv: fix sbi_remote_sfence_vma{,_asid}.
riscv: move switch_mm to its own file
riscv: move flush_icache_{all,mm} to cacheflush.c
tty: Don't force RISCV SBI console as preferred console
RISC-V: Access CSRs using CSR numbers
RISC-V: Add interrupt related SCAUSE defines in asm/csr.h
RISC-V: Use tabs to align macro values in asm/csr.h
RISC-V: Fix minor checkpatch issues.
RISC-V: Support nr_cpus command line option.
RISC-V: Implement nosmp commandline option.
RISC-V: Add RISC-V specific arch_match_cpu_phys_id
riscv: vdso: drop unnecessary cc-ldoption
riscv: call pm_power_off from machine_halt / machine_power_off
...
The Linux kernel will auto-disables all boot consoles whenever it
gets a preferred real console.
Currently on RISC-V systems, if we have a real console which is not
RISCV SBI console then boot consoles (such as earlycon=sbi) are not
auto-disabled when a real console (ttyS0 or ttySIF0) is available.
This results in duplicate prints at boot-time after kernel starts
using real console (i.e. ttyS0 or ttySIF0) if "earlycon=" kernel
parameter was passed by bootloader.
The reason for above issue is that RISCV SBI console always adds
itself as preferred console which is causing other real consoles
to be not used as preferred console.
Ideally "console=" kernel parameter passed by bootloaders should
be the one selecting a preferred real console.
This patch fixes above issue by not forcing RISCV SBI console as
preferred console.
Fixes: afa6b1ccfa ("tty: New RISC-V SBI console driver")
Cc: stable@vger.kernel.org
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
When kernel panic happens, it will first print the panic call stack,
then the ending msg like:
[ 35.743249] ---[ end Kernel panic - not syncing: Fatal exception
[ 35.749975] ------------[ cut here ]------------
The above message are very useful for debugging.
But if system is configured to not reboot on panic, say the
"panic_timeout" parameter equals 0, it will likely print out many noisy
message like WARN() call stack for each and every CPU except the panic
one, messages like below:
WARNING: CPU: 1 PID: 280 at kernel/sched/core.c:1198 set_task_cpu+0x183/0x190
Call Trace:
<IRQ>
try_to_wake_up
default_wake_function
autoremove_wake_function
__wake_up_common
__wake_up_common_lock
__wake_up
wake_up_klogd_work_func
irq_work_run_list
irq_work_tick
update_process_times
tick_sched_timer
__hrtimer_run_queues
hrtimer_interrupt
smp_apic_timer_interrupt
apic_timer_interrupt
For people working in console mode, the screen will first show the panic
call stack, but immediately overridden by these noisy extra messages,
which makes debugging much more difficult, as the original context gets
lost on screen.
Also these noisy messages will confuse some users, as I have seen many bug
reporters posted the noisy message into bugzilla, instead of the real
panic call stack and context.
Adding a flag "suppress_printk" which gets set in panic() to avoid those
noisy messages, without changing current kernel behavior that both panic
blinking and sysrq magic key can work as is, suggested by Petr Mladek.
To verify this, make sure kernel is not configured to reboot on panic and
in console
# echo c > /proc/sysrq-trigger
to see if console only prints out the panic call stack.
Link: http://lkml.kernel.org/r/1551430186-24169-1-git-send-email-feng.tang@intel.com
Signed-off-by: Feng Tang <feng.tang@intel.com>
Suggested-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kees Cook <keescook@chromium.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Updates to stm32 dma residue calculations
- Interleave dma capability to axi-dmac and
support for ZynqMP arch
- Rework of channel assignment for rcar dma
- Debugfs for pl330 driver
- Support for Tegra186/Tegra194, refactoring for new chips
and support for pause/resume
- Updates to axi-dmac, bcm2835, fsl-edma, idma64, imx-sdma,
rcar-dmac, stm32-dma etc
- dev_get_drvdata() updates on few drivers
-----BEGIN PGP SIGNATURE-----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=JDU6
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- Updates to stm32 dma residue calculations
- Interleave dma capability to axi-dmac and support for ZynqMP arch
- Rework of channel assignment for rcar dma
- Debugfs for pl330 driver
- Support for Tegra186/Tegra194, refactoring for new chips and support
for pause/resume
- Updates to axi-dmac, bcm2835, fsl-edma, idma64, imx-sdma, rcar-dmac,
stm32-dma etc
- dev_get_drvdata() updates on few drivers
* tag 'dmaengine-5.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (34 commits)
dmaengine: tegra210-adma: restore channel status
dmaengine: tegra210-dma: free dma controller in remove()
dmaengine: tegra210-adma: add pause/resume support
dmaengine: tegra210-adma: add support for Tegra186/Tegra194
Documentation: DT: Add compatibility binding for Tegra186
dmaengine: tegra210-adma: prepare for supporting newer Tegra chips
dmaengine: at_xdmac: remove a stray bottom half unlock
dmaengine: fsl-edma: Adjust indentation
dmaengine: fsl-edma: Fix typo in Vybrid name
dmaengine: stm32-dma: fix residue calculation in stm32-dma
dmaengine: nbpfaxi: Use dev_get_drvdata()
dmaengine: bcm-sba-raid: Use dev_get_drvdata()
dmaengine: stm32-dma: Fix unsigned variable compared with zero
dmaengine: stm32-dma: use platform_get_irq()
dmaengine: rcar-dmac: Update copyright information
dmaengine: imx-sdma: Only check ratio on parts that support 1:1
dmaengine: xgene-dma: fix spelling mistake "descripto" -> "descriptor"
dmaengine: idma64: Move driver name to the header
dmaengine: bcm2835: Drop duplicate capability setting.
dmaengine: pl330: _stop: clear interrupt status
...
Here is the "big" set of tty/serial driver patches for 5.2-rc1.
It's really pretty small, not much happening in this portion of the
kernel at the moment. When the "highlight" is the movement of the
documentation from .txt to .rst files, it's a good merge window.
There's a number of small fixes and updates over the various serial
drivers, and a new "tty null" driver for those embedded systems that
like to make things even smaller and not break things.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNKvrw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynR2wCfTrWM9Qm7oA1hgWeYZiLTrnYnOtsAoK4a629W
o7AAyVf8RJ4jdWaSgOqx
=9Dy/
-----END PGP SIGNATURE-----
Merge tag 'tty-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the "big" set of tty/serial driver patches for 5.2-rc1.
It's really pretty small, not much happening in this portion of the
kernel at the moment. When the "highlight" is the movement of the
documentation from .txt to .rst files, it's a good merge window.
There's a number of small fixes and updates over the various serial
drivers, and a new "tty null" driver for those embedded systems that
like to make things even smaller and not break things.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (45 commits)
tty: serial: add driver for the SiFive UART
dt-bindings: serial: add documentation for the SiFive UART driver
serial: uartps: Add support for cts-override
dt-bindings: xilinx-uartps: Add support for cts-override
serial: milbeaut_usio: Fix error handling in probe and remove
tty: rocket: deprecate the rp_ioctl
tty: rocket: Remove RCPK_GET_STRUCT ioctl
tty: update obsolete termios comment
tty: serial_core: fix error code returned by uart_register_driver()
serial: 8250-mtk: modify baudrate setting
serial: 8250-mtk: add follow control
docs: serial: convert docs to ReST and rename to *.rst
serial: 8250_exar: Adjust IOT2000 matching
TTY: serial_core, add ->install
serial: Fix using plain integer instead of Null pointer
tty:serial_core: Spelling mistake
tty: Add NULL TTY driver
tty: vt: keyboard: Allow Unicode compose base char
Revert "tty: fix NULL pointer issue when tty_port ops is not set"
serial: Add Milbeaut serial control
...
Here is the big staging and iio driver update for 5.2-rc1.
Lots of tiny fixes all over the staging and IIO driver trees here, along
with some new IIO drivers.
Also we ended up deleting two drivers, making this pull request remove a
few hundred thousand lines of code, always a nice thing to see. Both of
the drivers removed have been replaced with "real" drivers in their
various subsystem directories, and they will be coming to you from those
locations during this merge window.
There are some core vt/selection changes in here, that was due to some
cleanups needed for the speakup fixes. Those have all been acked by the
various subsystem maintainers (i.e. me), so those are ok.
We also added a few new drivers, for some odd hardware, giving new
developers plenty to work on with basic coding style cleanups to come in
the near future.
Other than that, nothing unusual here.
All of these have been in linux-next for a while with no reported
issues, other than an odd gcc warning for one of the new drivers that
should be fixed up soon.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNHGMQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynQRACgwtlC6DFsEFwCplYxQXP5uzuIVTMAoJ61xzC0
Qim7K31f5ulaa3GJuhzo
=zEY5
-----END PGP SIGNATURE-----
Merge tag 'staging-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / IIO driver updates from Greg KH:
"Here is the big staging and iio driver update for 5.2-rc1.
Lots of tiny fixes all over the staging and IIO driver trees here,
along with some new IIO drivers.
The "counter" subsystem was added in here as well, as it is needed by
the IIO drivers and subsystem.
Also we ended up deleting two drivers, making this pull request remove
a few hundred thousand lines of code, always a nice thing to see. Both
of the drivers removed have been replaced with "real" drivers in their
various subsystem directories, and they will be coming to you from
those locations during this merge window.
There are some core vt/selection changes in here, that was due to some
cleanups needed for the speakup fixes. Those have all been acked by
the various subsystem maintainers (i.e. me), so those are ok.
We also added a few new drivers, for some odd hardware, giving new
developers plenty to work on with basic coding style cleanups to come
in the near future.
Other than that, nothing unusual here.
All of these have been in linux-next for a while with no reported
issues, other than an odd gcc warning for one of the new drivers that
should be fixed up soon"
[ I fixed up the warning myself - Linus ]
* tag 'staging-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (663 commits)
staging: kpc2000: kpc_spi: Fix build error for {read,write}q
Staging: rtl8192e: Remove extra space before break statement
Staging: rtl8192u: ieee80211: Fix if-else indentation warning
Staging: rtl8192u: ieee80211: Fix indentation errors by removing extra spaces
staging: most: cdev: fix chrdev_region leak in mod_exit
staging: wlan-ng: Fix improper SPDX comment style
staging: rtl8192u: ieee80211: Resolve ERROR reported by checkpatch
staging: vc04_services: bcm2835-camera: Compress two lines into one line
staging: rtl8723bs: core: Use !x in place of NULL comparison.
staging: rtl8723bs: core: Prefer using the BIT Macro.
staging: fieldbus: anybus-s: fix wait_for_completion_timeout return handling
staging: kpc2000: fix up build problems with readq()
staging: rtlwifi: move remaining phydm .h files
staging: rtlwifi: strip down phydm .h files
staging: rtlwifi: delete the staging driver
staging: fieldbus: anybus-s: rename bus id field to avoid confusion
staging: fieldbus: anybus-s: keep device bus id in bus endianness
Staging: sm750fb: Change *array into *const array
staging: rtl8192u: ieee80211: Fix spelling mistake
staging: rtl8192u: ieee80211: Replace bit shifting with BIT macro
...
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlzMFaUACgkQt6xw3ITB
YzRICQgAiv7wF/yIbBhDOmCNCAKDO59chvFQWxXWdGk/aAB56kwKAMXJgLOvlMG/
VRuuLyParTFQETC3jaxKgnO/1hb+PZLDt2Q2KqixtjIzBypKUPWvK2sf6THhSRF1
GK0DBVUd1rCrWrR815+SPb8el4xXtdBzvAVB+Fx35PXVNpdRdqCkK+EQ6UnXGokm
rXXHbnfsnquBDtmb4CR4r2beH+aNElXbdt0Kj8VcE5J7f7jTdW3z6Q9WFRvdKmK7
yrsxXXB2w/EsWXOwFp0SLTV5+fgeGgTvv8uLjDw+SG6t0E0PebxjNAflT7dPrbYL
WecjKC9WqBxrGY+4ew6YJP70ijLBCw==
=aC8m
-----END PGP SIGNATURE-----
Merge tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull mmiowb removal from Will Deacon:
"Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb())
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
The only relatively recent changes have been addressing review
comments on the documentation, which is in a much better shape thanks
to the efforts of Ben and Ingo.
I was initially planning to split this into two pull requests so that
you could run the coccinelle script yourself, however it's been plain
sailing in linux-next so I've just included the whole lot here to keep
things simple"
* tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits)
docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section
arch: Remove dummy mmiowb() definitions from arch code
net/ethernet/silan/sc92031: Remove stale comment about mmiowb()
i40iw: Redefine i40iw_mmiowb() to do nothing
scsi/qla1280: Remove stale comment about mmiowb()
drivers: Remove explicit invocations of mmiowb()
drivers: Remove useless trailing comments from mmiowb() invocations
Documentation: Kill all references to mmiowb()
riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code
powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code
ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
m68k/io: Remove useless definition of mmiowb()
nds32/io: Remove useless definition of mmiowb()
x86/io: Remove useless definition of mmiowb()
arm64/io: Remove useless definition of mmiowb()
ARM/io: Remove useless definition of mmiowb()
mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors
...
Make the forward declaration actually match the real function
definition, something that previous versions of gcc had just ignored.
This is another patch to fix new warnings from gcc-9 before I start the
merge window pulls. I don't want to miss legitimate new warnings just
because my system update brought a new compiler with new warnings.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a serial driver for the SiFive UART, found on SiFive FU540 devices
(among others).
The underlying serial IP block is relatively basic, and currently does
not support serial break detection. Further information on the IP
block can be found in the documentation and Chisel sources:
https://static.dev.sifive.com/FU540-C000-v1.0.pdfhttps://github.com/sifive/sifive-blocks/tree/master/src/main/scala/devices/uart
This driver was written in collaboration with Wesley Terpstra
<wesley@sifive.com>.
Tested on a SiFive HiFive Unleashed A00 board, using BBL and the open-
source FSBL (using a DT file based on what's targeted for mainline).
This revision incorporates changes based on comments by Julia Lawall
<julia.lawall@lip6.fr>, Emil Renner Berthing <kernel@esmil.dk>, and
Andreas Schwab <schwab@suse.de>. Thanks also to Andreas for testing
the driver with his userspace and reporting a bug with the
set_termios implementation.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Wesley Terpstra <wesley@sifive.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Emil Renner Berthing <kernel@esmil.dk>
Cc: Andreas Schwab <schwab@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having flow is configurable. Add support for the same by
checking for cts-override.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_clk_get() is used so there is no reason to explicitly call
clk_put() in probe or remove functions. Also remove duplicate assign
for port->membase.
Fixes: ba44dc0430 ("serial: Add Milbeaut serial control")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Tested-by: Sugaya Taichi <sugaya.taichi@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rp_ioctl is deprecated.
Add dev_warn_ratelimited to warn the use of rp_ioctl.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the cmd is RCPK_GET_STRUCT, copy_to_user will copy
info to user space. As info->port.ops is the address of
a constant object rocket_port_ops (assigned in init_r_port),
a kernel address leakage happens.
Remove the RCPK_GET_STRUCT ioctl.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update an obsolete comment referring to the termios_locked structure
which was removed over a decade ago by commit fe6e29fdb1 ("tty:
simplify ktermios allocation").
While at it, fix the "Thus" typo.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_register_driver() returned -ENOMEM on any error, even when
tty_register_driver() call returned another one, such as -EBUSY.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SW and HW follow control function.
Signed-off-by: Long Cheng <long.cheng@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The converted files are focused at the Kernel internal API,
so, this is a good candidate for the kernel API set of books.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since there are more IOT2040 variants with identical hardware but
different asset tags, the asset tag matching should be adjusted to
support them.
As only the IOT2040 variants have the Exar chip on board, matching on
their board name is enough. In the future there will be no other devices
with the "SIMATIC IOT2000" DMI board name but different hardware.
Signed-off-by: Su Bao Cheng <baocheng.su@siemens.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to compute the uart state only on the first open. This is
usually what is done in the ->install hook. serial_core used to do this
in ->open on every open. So move it to ->install.
As a side effect, it ensures the state is set properly in the window
after tty_init_dev is called, but before uart_open. This fixes a bunch
of races between tty_open and flush_to_ldisc we were dealing with
recently.
One of such bugs was attempted to fix in commit fedb576064 (serial:
fix race between flush_to_ldisc and tty_open), but it only took care of
a couple of functions (uart_start and uart_unthrottle). I was able to
reproduce the crash on a SLE system, but in uart_write_room which is
also called from flush_to_ldisc via process_echoes. I was *unable* to
reproduce the bug locally. It is due to having this patch in my queue
since 2012!
general protection fault: 0000 [#1] SMP KASAN PTI
CPU: 1 PID: 5 Comm: kworker/u4:0 Tainted: G L 4.12.14-396-default #1 SLE15-SP1 (unreleased)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-0-ga698c89-prebuilt.qemu.org 04/01/2014
Workqueue: events_unbound flush_to_ldisc
task: ffff8800427d8040 task.stack: ffff8800427f0000
RIP: 0010:uart_write_room+0xc4/0x590
RSP: 0018:ffff8800427f7088 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 000000000000002f RSI: 00000000000000ee RDI: ffff88003888bd90
RBP: ffffffffb9545850 R08: 0000000000000001 R09: 0000000000000400
R10: ffff8800427d825c R11: 000000000000006e R12: 1ffff100084fee12
R13: ffffc900004c5000 R14: ffff88003888bb28 R15: 0000000000000178
FS: 0000000000000000(0000) GS:ffff880043300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000561da0794148 CR3: 000000000ebf4000 CR4: 00000000000006e0
Call Trace:
tty_write_room+0x6d/0xc0
__process_echoes+0x55/0x870
n_tty_receive_buf_common+0x105e/0x26d0
tty_ldisc_receive_buf+0xb7/0x1c0
tty_port_default_receive_buf+0x107/0x180
flush_to_ldisc+0x35d/0x5c0
...
0 in rbx means tty->driver_data is NULL in uart_write_room. 0x178 is
tried to be dereferenced (0x178 >> 3 is 0x2f in rdx) at
uart_write_room+0xc4. 0x178 is exactly (struct uart_state *)NULL->refcount
used in uart_port_lock from uart_write_room.
So revert the upstream commit here as my local patch should fix the
whole family.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Li RongQing <lirongqing@baidu.com>
Cc: Wang Li <wangli39@baidu.com>
Cc: Zhang Yu <zhangyu31@baidu.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix build warning that using plain integer as Null pointer.
This is reported by kbuild test robot.
Fixes: ba44dc0430 ("serial: Add Milbeaut serial control")
Signed-off-by: Sugaya Taichi <sugaya.taichi@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch breaks set_selection() into two functions so that when
called from kernel, copy_from_user() can be avoided. The two functions
are called set_selection_user() and set_selection_kernel() in order to
be explicit about their purposes. This also means updating any
references to set_selection() and fixing for name change. It also
exports set_selection_kernel() and paste_selection().
These changes are used the following patch where speakup's selection
functionality calls into the above functions, thereby doing away with
parallel implementation.
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Tested-by: Gregory Nowak <greg@gregn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err_spi is only called within SERIAL_SC16IS7XX_SPI
while err_i2c is called inside SERIAL_SC16IS7XX_I2C.
So we need to put err_spi and err_i2c into each #ifdef
accordingly.
This change fixes ("sc16is7xx: move label 'err_spi'
to correct section").
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch a6dbe44275 ("vt: perform safe console erase in the right
order") introduced a bug. The conditional do_update_region() was
replaced by a call to update_region() that does contain the conditional
already, but with unwanted extra side effects such as restoring the cursor
drawing.
In order to reproduce the bug:
- use framebuffer console with the AMDGPU driver
- type "links" to start the console www browser
- press 'q' and space to exit links
Now the cursor will be permanently visible in the center of the
screen. It will stay there until something overwrites it.
The bug goes away if we change update_region() back to the conditional
do_update_region().
[ nico: reworded changelog ]
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Cc: stable@vger.kernel.org
Fixes: a6dbe44275 ("vt: perform safe console erase in the right order")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err_spi is used when SERIAL_SC16IS7XX_SPI is enabled, so make
the label only available under SERIAL_SC16IS7XX_SPI option.
Otherwise, the below warning appears.
drivers/tty/serial/sc16is7xx.c:1523:1: warning: label ‘err_spi’ defined but not used [-Wunused-label]
err_spi:
^~~~~~~
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Fixes: ac0cdb3d99 ("sc16is7xx: missing unregister/delete driver on error in sc16is7xx_init()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The calculation of the sampling point has min() and max() exchanged.
Fix this by using the clamp() helper instead.
Fixes: 63ba1e00f1 ("serial: sh-sci: Support for HSCIF RX sampling point adjustment")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are several issues with the formula used for calculating the
deviation from the intended rate:
1. While min_err and last_stop are signed, srr and baud are unsigned.
Hence the signed values are promoted to unsigned, which will lead
to a bogus value of deviation if min_err is negative,
2. Srr is the register field value, which is one less than the actual
sampling rate factor,
3. The divisions do not use rounding.
Fix this by casting unsigned variables to int, adding one to srr, and
using a single DIV_ROUND_CLOSEST().
Fixes: 63ba1e00f1 ("serial: sh-sci: Support for HSCIF RX sampling point adjustment")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If no console driver is enabled (or if a non-present driver is selected
with something like console=null in an attempt to disable the console),
opening /dev/console errors out, and init scripts and other userspace
code that relies on the existence of a console will fail. Symlinking
/dev/null to /dev/console does not solve the problem since /dev/null
does not behave like a real TTY.
To just provide a dummy console to userspace when no console driver is
available or desired, add a ttynull driver which simply discards all
writes. It can be chosen on the command line in the standard way, i.e.
with console=ttynull.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass Unicode character to k_unicode handler function to honor possible
accent_table definition.
With introduction of KDSKBDIACRUC ioctl, it has been possible to set
compose characters (diacr, base and result) to any Unicode character
(below 0xf000 code point) as defined in struct kbdiacruc.
But it does not work with characters beyond Latin-1 as base, because
they are printed early and not passed to any of the handler functions,
thus breaking compose and dead keys.
It affects keyboard layouts defining such characters on level 1 and
relying on dead keys to access level 3 (e.g., lv-modern with some
modifications for extra characters on level 3 for ē, ā and ī keys).
Signed-off-by: Reinis Danne <rei4dan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f4e68d58cf.
TTY drivers using the tty-port abstraction all provide a pointer to a
set of port operations, which specifically cannot be NULL (or we'd find
out at first attempt to open a port).
Revert the recent commit which added unnecessary NULL-checks and whose
commit message indicated that it was fixing a real problem, which it did
not.
Note that even the two tty drivers for virtual devices currently
providing an empty set of operations probably should be implementing at
least some of the callbacks.
Cc: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add Milbeaut serial control including earlycon and console.
Signed-off-by: Sugaya Taichi <sugaya.taichi@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GIO_UNIMAP can easily result in a high order allocation,
seen 6th order allocation on radeondrmfb:
fbcon: radeondrmfb (fb0) is primary device
Console: switching to colour frame buffer device 160x64
radeon 0000:01:05.0: fb0: radeondrmfb frame buffer device
WARNING: CPU: 0 PID: 78661 at mm/page_alloc.c:3532
__alloc_pages_nodemask+0x1b1/0x600
order 6 >= 3, gfp 0x40d0
The warning is generated by a debug patch.
At the same time it's safe to use kvmalloc() for allocation in
con_get_unimap(), so let's do the substitution.
And do the same for con_set_unimap().
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'default n' is the default value for any bool or tristate Kconfig
setting so there is no need to write it explicitly.
Also since commit f467c5640c ("kconfig: only write '# CONFIG_FOO
is not set' for visible symbols") the Kconfig behavior is the same
regardless of 'default n' being present or not:
...
One side effect of (and the main motivation for) this change is making
the following two definitions behave exactly the same:
config FOO
bool
config FOO
bool
default n
With this change, neither of these will generate a
'# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
That might make it clearer to people that a bare 'default n' is
redundant.
...
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return from tty_write_room could potentially be negative if
a tty write_room driver returns an error number (not that any seem
to do). Rather than just check for a zero return, also check for
a -ve return. This avoids the unsigned nr being set to a large unsigned
value on the assignment from variable space and can lead to overflowing
the buffer buf. Better to be safe than assume all write_room
implementations in tty drivers are going to do the right thing.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
There were a few straggling files under drivers/tty/ that did not have
any SPDX identifier either because they entered the tree recently, or
they somehow missed the mass-tagging of commit b24413180f ("License
cleanup: add SPDX GPL-2.0 license identifier to files with no license")
This commit follows the same rule as b24413180f ("License cleanup: add
SPDX GPL-2.0 license identifier to files with no license") where files
without any specified license in them fall under GPL-2.0 as the correct
license for the individual file. Add that identifier to these remaining
files so that we don't have to guess at the license of them in the
future.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There were a few Kconfig and Makefiles under drivers/tty/ that were
missing a SPDX identifier. Fix that up so that automated tools can
properly classify all kernel source files.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Acked-by: David Sterba <dsterba@suse.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b9ca5f8560 as 0-day
shows it has a circular locking dependency.
Fixes: b9ca5f8560 ("tty: pty: Fix race condition between release_one_tty and pty_write")
Reported-by: kernel test robot <lkp@intel.com>
Cc: Sahara <keun-o.park@darkmatter.ae>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both /dev/vcs and /dev/vcs0 were in use in the past, but these days
/dev/vcs0 is mostly historical curiosity.
* "/dev/vcs" is the name that has always been in the Linux allocated
devices list.
* "vcs" is the device name in sysfs since Linux v2.6.12.
* MAKEDEV(1) in Debian used to create /dev/vcs0 only, but /dev/vcs was
added in 1999: https://bugs.debian.org/45698
* MAKEDEV(1) in RedHat switched from /dev/vcs0 to /dev/vcs in 2000:
* Fri Oct 20 2000 Nalin Dahyabhai <nalin@redhat.com>
- change vcs0 to vcs (ditto for vcsa0)
Signed-off-by: Jakub Wilk <jwilk@jwilk.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Especially when a linked tty is used such as pty, the linked tty
port's buf works have not been cancelled while master tty port's
buf work has been cancelled. Since release_one_tty and flush_to_ldisc
run in workqueue threads separately, when pty_cleanup happens and
link tty port is freed, flush_to_ldisc tries to access freed port
and port->itty, eventually it causes a panic.
This patch utilizes the magic value with holding the tty_mutex to
check if the tty->link is valid.
Fixes: 2b022ab754 ("pty: cancel pty slave port buf's work in tty_release")
Signed-off-by: Sahara <keun-o.park@darkmatter.ae>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, in the userspace, it was possible to use the "setterm" command
from util-linux to blank the VT console by default, using the following
command.
According to the man page,
> The force option keeps the screen blank even if a key is pressed.
It was implemented by calling TIOCL_BLANKSCREEN.
case BLANKSCREEN:
ioctlarg = TIOCL_BLANKSCREEN;
if (ioctl(STDIN_FILENO, TIOCLINUX, &ioctlarg))
warn(_("cannot force blank"));
break;
However, after Linux 4.12, this command ceased to work anymore, which is
unexpected. By inspecting the kernel source, it shows that the issue was
triggered by the side-effect from commit a4199f5eb8 ("tty: Disable
default console blanking interval").
The console blanking is implemented by function do_blank_screen() in vt.c:
"blank_state" will be initialized to "blank_normal_wait" in con_init() if
AND ONLY IF ("blankinterval" > 0). If "blankinterval" is 0, "blank_state"
will be "blank_off" (== 0), and a call to do_blank_screen() will always
abort, even if a forced blanking is required from the user by calling
TIOCL_BLANKSCREEN, the console won't be blanked.
This behavior is unexpected from a user's point-of-view, since it's not
mentioned in any documentation. The setterm man page suggests it will
always work, and the kernel comments in uapi/linux/tiocl.h says
> /* keep screen blank even if a key is pressed */
> #define TIOCL_BLANKSCREEN 14
To fix it, we simply remove the "blank_state != blank_off" check, as
pointed out by Nicolas Pitre, this check doesn't logically make sense
and it's safe to remove.
Suggested-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Fixes: a4199f5eb8 ("tty: Disable default console blanking interval")
Signed-off-by: Yifeng Li <tomli@tomli.me>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ipw->attr_memory and ipw->common_memory are assigned with the
return value of ioremap. ioremap may fail, but no checks
are enforced. The fix inserts the checks to avoid potential
NULL pointer dereferences.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The intention was clearly to use the tty_pgrp local variable rather than
re-read tty->pgrp outside of ctrl_lock, so do that.
This bug was introduced by commit 2812d9e9fd ("tty: Combine
SIGTTOU/SIGTTIN handling").
Signed-off-by: David Emett <dave@sp4m.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building with W=1 reports (among other things):
CC drivers/tty/tty_jobctrl.o
drivers/tty/tty_jobctrl.c:317: warning: Cannot understand *
on line 317 - I thought it was a doc line
Fix up the non-kerneldoc comment. (other warnings to be cleaned up in separate patch)
Signed-off-by Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Systems which don't provide arch_trigger_cpumask_backtrace() will
invoke showacpu() from a smp_call_function() function which is invoked
with disabled interrupts even on -RT systems.
The function acquires the show_lock lock which only purpose is to
ensure that the CPUs don't print simultaneously. Otherwise the
output would clash and it would be hard to tell the output from CPUx
apart from CPUy.
On -RT the spin_lock() can not be acquired from this context. A
raw_spin_lock() is required. It will introduce the system's latency
by performing the sysrq request and other CPUs will block on the lock
until the request is done. This is okay because the user asked for a
backtrace of all active CPUs and under "normal circumstances in
production" this path should not be triggered.
Signed-off-by: Julien Grall <julien.grall@arm.com>
[bigeasy@linuxtronix.de: commit description]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike 'client_ops' which is initialized to 'default_client_ops', the
port operations 'ops' may be left to NULL.
Check the 'ops' value before checking the 'ops->x' value.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is an ACPI method to enumerate such devices via specific ACPI ID
and use of compatible strings. It will not work for the drivers which
have no OF match ID table present.
Reported-by: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Tested-By: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of open coded variants, switch to direct use of
device_get_match_data().
Tested-By: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the property is provided and there are no other possibilities to detect
UART clock frequency, use it as a fallback.
Tested-By: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add DMA mode support for the Spreadtrum serial controller.
Signed-off-by: Lanqing Liu <lanqing.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds power management for the Spreadtrum serial controller.
Signed-off-by: Lanqing Liu <lanqing.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix sparse warning:
drivers/tty/serial/8250/8250_fintek.c:306:6: warning:
symbol 'fintek_8250_set_termios' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Echo "" to /sys/module/kgdboc/parameters/kgdboc will fail with "No such
device” error.
This is caused by function "configure_kgdboc" who init err to ENODEV
when the config is empty (legal input) the code go out with ENODEV
returned.
Fixes: 2dd4531686 ("kgdboc: Fix restrict error")
Signed-off-by: Wentao Wang <witallwang@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In half-duplex operation, RX should be started after TX completes.
If DMA is used, there is a case when the DMA transfer completes but the
TX FIFO is not emptied, so the RX cannot be restarted just yet.
Use a boolean variable to store this state and rearm TX interrupt mask
to be signaled again that the transfer finished. In interrupt transmit
handler this variable is used to start RX. A warning message is generated
if RX is activated before TX fifo is cleared.
Fixes: b389f173aa ("tty/serial: atmel: RS485 half duplex w/DMA: enable
RX after TX is done")
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a helper function to check that a port needs to use half duplex
communication, replacing several occurrences of multi-line bit checking.
Fixes: b389f173aa ("tty/serial: atmel: RS485 half duplex w/DMA: enable RX after TX is done")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel IOMMU, when enabled, tries to find the domain of the device,
assuming it's a PCI one, during DMA operations, such as mapping or
unmapping. Since we are splitting the actual PCI device to couple of
children via MFD framework (see drivers/mfd/intel-lpss.c for details),
the DMA device appears to be a platform one, and thus not an actual one
that performs DMA. In a such situation IOMMU can't find or allocate
a proper domain for its operations. As a result, all DMA operations are
failed.
In order to fix this, supply parent of the platform device
to the DMA engine framework and fix filter functions accordingly.
We may rely on the fact that parent is a real PCI device, because no
other configuration is present in the wild.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [for tty parts]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We disable transmission interrupt (clear SCSCR_TIE) after all data has been transmitted
(if uart_circ_empty(xmit)). While transmitting, if the data is still in the tty buffer,
re-enable the SCSCR_TIE bit, which was done at sci_start_tx().
This is unnecessary processing, wasting CPU operation if the data transmission length is large.
And further, transmit end, FIFO empty bits disabling have also been performed in the step above.
Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrey has reported on OpenWrt's bug tracking system[1], that he
currently can't use ar93xx_uart as pure serial UART without console
(CONFIG_SERIAL_8250_CONSOLE and CONFIG_SERIAL_AR933X_CONSOLE undefined),
because compilation ends with following error:
ar933x_uart.c: In function 'ar933x_uart_console_write':
ar933x_uart.c:550:14: error: 'struct uart_port' has no
member named 'sysrq'
So this patch moves all the code related to console handling behind
series of CONFIG_SERIAL_AR933X_CONSOLE ifdefs.
1. https://bugs.openwrt.org/index.php?do=details&task_id=2152
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Andrey Batyiev <batyiev@gmail.com>
Reported-by: Andrey Batyiev <batyiev@gmail.com>
Tested-by: Andrey Batyiev <batyiev@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When building with -Wsometimes-uninitialized, Clang warns:
drivers/tty/serial/qcom_geni_serial.c:1079:6: warning: variable 'baud'
is used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
It's not wrong; when options is NULL, baud has no default value. Use
9600 as that is a sane default.
Link: https://github.com/ClangBuiltLinux/linux/issues/395
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing uart_unregister_driver() and i2c_del_driver() before return
from sc16is7xx_init() in the error handling case.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case ioremap fails, the fix returns -ENOMEM to avoid NULL
pointer dereferences.
Multiple places use port.membase.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_match_device can return a NULL pointer when matching device is not
found. This patch avoids a scenario causing NULL pointer derefernce.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_match_device on failure to find a matching device can return a NULL
pointer. The patch checks for such a scenrio and passes the error upstream.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- dmatest updates for modularizing common struct and code
- remove SG support for VDMA xilinx IP and updates to driver
- Update to dw driver to support Intel iDMA controllers
multi-block support
- tegra updates for proper reporting of residue
- Add Snow Ridge ioatdma device id and support for IOATDMA v3.4
- struct_size() usage and useless LIST_HEAD cleanups in subsystem.
- qDMA controller driver for Layerscape SoCs
- stm32-dma PM Runtime support
- And usual updates to imx-sdma, sprd, Documentation, fsl-edma,
bcm2835, qcom_hidma etc
-----BEGIN PGP SIGNATURE-----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=Ykvn
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.1-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- dmatest updates for modularizing common struct and code
- remove SG support for VDMA xilinx IP and updates to driver
- Update to dw driver to support Intel iDMA controllers multi-block
support
- tegra updates for proper reporting of residue
- Add Snow Ridge ioatdma device id and support for IOATDMA v3.4
- struct_size() usage and useless LIST_HEAD cleanups in subsystem.
- qDMA controller driver for Layerscape SoCs
- stm32-dma PM Runtime support
- And usual updates to imx-sdma, sprd, Documentation, fsl-edma,
bcm2835, qcom_hidma etc
* tag 'dmaengine-5.1-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (81 commits)
dmaengine: imx-sdma: fix consistent dma test failures
dmaengine: imx-sdma: add a test for imx8mq multi sdma devices
dmaengine: imx-sdma: add clock ratio 1:1 check
dmaengine: dmatest: move test data alloc & free into functions
dmaengine: dmatest: add short-hand `buf_size` var in dmatest_func()
dmaengine: dmatest: wrap src & dst data into a struct
dmaengine: ioatdma: support latency tolerance report (LTR) for v3.4
dmaengine: ioatdma: add descriptor pre-fetch support for v3.4
dmaengine: ioatdma: disable DCA enabling on IOATDMA v3.4
dmaengine: ioatdma: Add Snow Ridge ioatdma device id
dmaengine: sprd: Change channel id to slave id for DMA cell specifier
dt-bindings: dmaengine: sprd: Change channel id to slave id for DMA cell specifier
dmaengine: mv_xor: Use correct device for DMA API
Documentation :dmaengine: clarify DMA desc. pointer after submission
Documentation: dmaengine: fix dmatest.rst warning
dmaengine: k3dma: Add support for dma-channel-mask
dmaengine: k3dma: Delete axi_config
dmaengine: k3dma: Upgrade k3dma driver to support hisi_asp_dma hardware
Documentation: bindings: dma: Add binding for dma-channel-mask
Documentation: bindings: k3dma: Extend the k3dma driver binding to support hisi-asp
...
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAlyCpL0UHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vzoHw//ZyFbwekF0mV3RZwcV35LkScIOw0d
O1DgjJo8UbuV51+/foQeUZ8IzjHlybQhoFdJupPuw+LyaDUkwqjAmdtY8J/FjWSm
AJeVzu6gMF0Z9kwwGO4NyqX2EWluTD0xNLgf8g+fe3p1MtEuH6VCrqe+hk3wma0K
CrSIKWY/sO408SpAaWiLTEZmVT+hXiP9hJw1qTrbqKLtyWa4oCjErdoyUDsA01+5
gPndKC/3pu6q6q9Dd94582HuQaE2dKHWQXx6Fzd/tdCyYffpbOUAUNP3aRXaTKrS
MwKxOF3y7yUnz5RbxRgopwNVf5WyXhCnnPZRLaSxqnTSZCY6FCUi3l6RpVyWu2Ha
iztBbkTP/x6WV3VWg810qgQKQ9wl8oALMkoOfR6lWCR7MTuJnMXJtbrz0jWpEC2O
ZPwK9fAxFj2/3e13hx88O7Ek8kfajTPM8T15K79pvpljfqa0BD9SrhPyQ5ssmxj4
idz4yIFCATULKszPXA1QbfC1/xCDveQOEPSerL3eACXsLN17vfpOwOT9vWJm6bpr
6u5ggM2dEA07eI1ANnY6twn5g0kSYU9qISNQO98tA86IvaCnME0Z+k+SCwUNIM9U
ep9k0NdAGDNsYOfdVEEY0fYGT9k+9f9w8AfZLNvh0N3s7mGQQ35jf0Z75jj/jsor
cbMcPAN2jOCyFVs=
=vf9L
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Use match_string() instead of reimplementing it (Andy Shevchenko)
- Enable SERR# forwarding for all bridges (Bharat Kumar Gogada)
- Use Latency Tolerance Reporting if already enabled by platform (Bjorn
Helgaas)
- Save/restore LTR info for suspend/resume (Bjorn Helgaas)
- Fix DPC use of uninitialized data (Dongdong Liu)
- Probe bridge window attributes only once at enumeration-time to fix
device accesses during rescan (Bjorn Helgaas)
- Return BAR size (not "size -1 ") from pci_size() to simplify code (Du
Changbin)
- Use config header type (not class code) identify bridges more
reliably (Honghui Zhang)
- Work around Intel Denverton incorrect Trace Hub BAR size reporting
(Alexander Shishkin)
- Reorder pciehp cached state/hardware state updates to avoid missed
interrupts (Mika Westerberg)
- Turn ibmphp semaphores into completions or mutexes (Arnd Bergmann)
- Mark expected switch fall-through (Mathieu Malaterre)
- Use of_node_name_eq() for node name comparisons (Rob Herring)
- Add ACS and pciehp quirks for HXT SD4800 (Shunyong Yang)
- Consolidate Rohm Vendor ID definitions (Andy Shevchenko)
- Use u32 (not __u32) for things not exposed to userspace (Logan
Gunthorpe)
- Fix locking semantics of bus and slot reset interfaces (Alex
Williamson)
- Update PCIEPORTBUS Kconfig help text (Hou Zhiqiang)
- Allow portdrv to claim subtractive decode Ports so PCIe services will
work for them (Honghui Zhang)
- Report PCIe links that become degraded at run-time (Alexandru
Gagniuc)
- Blacklist Gigabyte X299 Root Port power management to fix Thunderbolt
hotplug (Mika Westerberg)
- Revert runtime PM suspend/resume callbacks that broke PME on network
cable plug (Mika Westerberg)
- Disable Data Link State Changed interrupts to prevent wakeup
immediately after suspend (Mika Westerberg)
- Extend altera to support Stratix 10 (Ley Foon Tan)
- Allow building altera driver on ARM64 (Ley Foon Tan)
- Replace Douglas with Tom Joseph as Cadence PCI host/endpoint
maintainer (Lorenzo Pieralisi)
- Add DT support for R-Car RZ/G2E (R8A774C0) (Fabrizio Castro)
- Add dra72x/dra74x/dra76x SoC compatible strings (Kishon Vijay Abraham I)
- Enable x2 mode support for dra72x/dra74x/dra76x SoC (Kishon Vijay
Abraham I)
- Configure dra7xx PHY to PCIe mode (Kishon Vijay Abraham I)
- Simplify dwc (remove unnecessary header includes, name variables
consistently, reduce inverted logic, etc) (Gustavo Pimentel)
- Add i.MX8MQ support (Andrey Smirnov)
- Add message to help debug dwc MSI-X mask bit errors (Gustavo
Pimentel)
- Work around imx7d PCIe PLL erratum (Trent Piepho)
- Don't assert qcom reset GPIO during probe (Bjorn Andersson)
- Skip dwc MSI init if MSIs have been disabled (Lucas Stach)
- Use memcpy_fromio()/memcpy_toio() instead of plain memcpy() in PCI
endpoint framework (Wen Yang)
- Add interface to discover supported endpoint features to replace a
bitfield that wasn't flexible enough (Kishon Vijay Abraham I)
- Implement the new supported-feature interface for designware-plat,
dra7xx, rockchip, cadence (Kishon Vijay Abraham I)
- Fix issues with 64-bit BAR in endpoints (Kishon Vijay Abraham I)
- Add layerscape endpoint mode support (Xiaowei Bao)
- Remove duplicate struct hv_vp_set in favor of struct hv_vpset (Maya
Nakamura)
- Rework hv_irq_unmask() to use cpumask_to_vpset() instead of
open-coded reimplementation (Maya Nakamura)
- Align Hyper-V struct retarget_msi_interrupt arguments (Maya Nakamura)
- Fix mediatek MMIO size computation to enable full size of available
MMIO space (Honghui Zhang)
- Fix mediatek DMA window size computation to allow endpoint DMA access
to full DRAM address range (Honghui Zhang)
- Fix mvebu prefetchable BAR regression caused by common bridge
emulation that assumed all bridges had prefetchable windows (Thomas
Petazzoni)
- Make advk_pci_bridge_emul_ops static (Wei Yongjun)
- Configure MPS settings for VMD root ports (Jon Derrick)
* tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (92 commits)
PCI: Update PCIEPORTBUS Kconfig help text
PCI: Fix "try" semantics of bus and slot reset
PCI/LINK: Report degraded links via link bandwidth notification
dt-bindings: PCI: altera: Add altr,pcie-root-port-2.0
PCI: altera: Enable driver on ARM64
PCI: altera: Add Stratix 10 PCIe support
PCI/PME: Fix possible use-after-free on remove
PCI: aardvark: Make symbol 'advk_pci_bridge_emul_ops' static
PCI: dwc: skip MSI init if MSIs have been explicitly disabled
PCI: hv: Refactor hv_irq_unmask() to use cpumask_to_vpset()
PCI: hv: Replace hv_vp_set with hv_vpset
PCI: hv: Add __aligned(8) to struct retarget_msi_interrupt
PCI: mediatek: Enlarge PCIe2AHB window size to support 4GB DRAM
PCI: mediatek: Fix memory mapped IO range size computation
PCI: dwc: Remove superfluous shifting in definitions
PCI: dwc: Make use of GENMASK/FIELD_PREP
PCI: dwc: Make use of BIT() in constant definitions
PCI: dwc: Share code for dw_pcie_rd/wr_other_conf()
PCI: dwc: Make use of IS_ALIGNED()
PCI: imx6: Add code to request/control "pcie_aux" clock for i.MX8MQ
...
-----BEGIN PGP SIGNATURE-----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=57/1
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20190305' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit updates from Paul Moore:
"A lucky 13 audit patches for v5.1.
Despite the rather large diffstat, most of the changes are from two
bug fix patches that move code from one Kconfig option to another.
Beyond that bit of churn, the remaining changes are largely cleanups
and bug-fixes as we slowly march towards container auditing. It isn't
all boring though, we do have a couple of new things: file
capabilities v3 support, and expanded support for filtering on
filesystems to solve problems with remote filesystems.
All changes pass the audit-testsuite. Please merge for v5.1"
* tag 'audit-pr-20190305' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: mark expected switch fall-through
audit: hide auditsc_get_stamp and audit_serial prototypes
audit: join tty records to their syscall
audit: remove audit_context when CONFIG_ AUDIT and not AUDITSYSCALL
audit: remove unused actx param from audit_rule_match
audit: ignore fcaps on umount
audit: clean up AUDITSYSCALL prototypes and stubs
audit: more filter PATH records keyed on filesystem magic
audit: add support for fcaps v3
audit: move loginuid and sessionid from CONFIG_AUDITSYSCALL to CONFIG_AUDIT
audit: add syscall information to CONFIG_CHANGE records
audit: hand taken context to audit_kill_trees for syscall logging
audit: give a clue what CONFIG_CHANGE op was involved
Existing driver checks for alternate clock if devm_clk_get() fails
and returns error code for last clock failure. If xilinx_uartps is
called before clock driver, devm_clk_get() returns -EPROBE_DEFER.
In this case, probe should not check for alternate clock as main
clock is already present in DTS and return -EPROBE_DEFER only.
This patch fixes it by not checking for alternate clock when main
clock get returns -EPROBE_DEFER.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the source clock is not divisible by the expected baud rate and
the remainder is not less than half of the expected baud rate, the old
formular will round up the frequency division coefficient. This will
make the actual baud rate less than the expected value and can not meet
the external transmission requirements.
Thus this patch modifies the baud rate calculation formula to support
the serial controller output the maximum baud rate.
Signed-off-by: Lanqing Liu <lanqing.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two other drivers that bind to mrvl,mmp-uart and both of them
assume register shift of 2 bits. There are device trees that lack the
property and rely on that assumption.
If this driver wins the race to bind to those devices, it should behave
the same as the older deprecated driver.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like the other OF-enabled drivers, use the port number from the firmware if
the devicetree specifies an alias:
aliases {
...
serial2 = &uart2; /* Should be ttyS2 */
}
This is how the deprecated pxa.c driver behaved, switching to 8250_pxa
messes up the numbering.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warning:
drivers/tty/hvc/hvc_xen.c: In function ‘xencons_backend_changed’:
drivers/tty/hvc/hvc_xen.c:493:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (dev->state == XenbusStateClosed)
^
drivers/tty/hvc/hvc_xen.c:496:2: note: here
case XenbusStateClosing:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/tty/n_gsm.c: In function ‘gsm_dlci_data’:
drivers/tty/n_gsm.c:1582:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (tty) {
^
drivers/tty/n_gsm.c:1587:2: note: here
case 1:
^~~~
drivers/tty/n_gsm.c: In function ‘gsm1_receive’:
CC [M] drivers/scsi/snic/snic_disc.o
CC [M] drivers/net/wireless/realtek/rtlwifi/pci.o
CC drivers/usb/early/xhci-dbc.o
drivers/tty/n_gsm.c:1981:12: warning: this statement may fall through [-Wimplicit-fallthrough=]
gsm->fcs = INIT_FCS;
^
drivers/tty/n_gsm.c:1983:2: note: here
case GSM_ADDRESS: /* Address continuation */
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to the complexities of modern Qualcomm SoCs, about a half dozen drivers
must successfully probe before the clocks for the console are present, and
the console can successfully probe. Depending on several random factors
such as probe order and modules vs builtin, msm_serial may not be able to
successfully probe for some, at which point, __init annotated functions
may become unmapped. If this occurs, msm_console_setup() will be called
from the probe path, but will no longer exist, resulting in a kernel
panic.
Resolve this issue by removing the __init annotation from
msm_console_setup().
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Exynos 5260, like the 5433, appears to require baud clock as
well as pclk to be running before accessing any of the registers,
otherwise an external abort is raised.
The serial driver already enables baud clock when required, but only
if it knows which clock is baud clock. On older SoCs baud clock may be
selected from a number of possible clocks so to support this the driver
only selects which clock to use for baud clock when a port is opened,
at which point the desired baud rate is known and the best clock can be
selected.
The result is that there are a number of circumstances in which
registers are accessed without first explicitly enabling baud clock:
- while the driver is being initialised
- the initial parts of opening a port for the first time
- when resuming if the port hasn't been already opened
The 5433 overcomes this currently by marking the baud clock as
CLK_IGNORE_UNUSED, so the clock is always enabled, however
for the 5260 I've been trying to avoid this.
This change adds code to pick the first available clock to use
as baud clock and enables it while initialising the driver.
This code wouldn't be sufficient on a SoC which supports
multiple possible baud clock sources _and_ requires the
correct baud clock to be enabled before accessing any of the
serial port registers (in particular the register which selects
which clock to use as the baud clock). As far as I know
such hardware doesn't exist.
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If RX is disabled while there are still unprocessed bytes in RX FIFO,
cdns_uart_handle_rx() called from interrupt handler will get stuck in
the receive loop as read bytes will not get removed from the RX FIFO
and CDNS_UART_SR_RXEMPTY bit will never get set.
Avoid the stuck handler by checking first if RX is disabled. port->lock
protects against race with RX-disabling functions.
This HW behavior was mentioned by Nathan Rossi in 43e98facc4a3 ("tty:
xuartps: Fix RX hang, and TX corruption in termios call") which fixed a
similar issue in cdns_uart_set_termios().
The behavior can also be easily verified by e.g. setting
CDNS_UART_CR_RX_DIS at the beginning of cdns_uart_handle_rx() - the
following loop will then get stuck.
Resetting the FIFO using RXRST would not set RXEMPTY either so simply
issuing a reset after RX-disable would not work.
I observe this frequently on a ZynqMP board during heavy RX load at 1M
baudrate when the reader process exits and thus RX gets disabled.
Fixes: 61ec901698 ("tty/serial: add support for Xilinx PS UART")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
unlikely has already included in IS_ERR(),
so just remove redundant likely annotation.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/tty/n_hdlc.c: In function ‘n_hdlc_tty_ioctl’:
drivers/tty/n_hdlc.c:775:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
switch (arg) {
^~~~~~
drivers/tty/n_hdlc.c:782:2: note: here
default:
^~~~~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The four port Pericom chips have the fourth port at the wrong address.
Make use of quirk to fix it.
Fixes: c8d192428f ("serial: 8250: added acces i/o products quad and octal serial cards")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Have the correct number of ports created for ACCES serial cards. Two port
cards show up as four ports, and four port cards show up as eight.
Fixes: c8d192428f ("serial: 8250: added acces i/o products quad and octal serial cards")
Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4b4ecd9cb8 ("vt: Perform safe console erase only once") removed
what appeared to be an extra call to scr_memsetw(). This missed the fact
that set_origin() must be called before clearing the screen otherwise
old screen content gets restored on the screen when using vgacon. Let's
fix that by moving all the scrollback handling to flush_scrollback()
where it logically belongs, and invoking it before the actual screen
clearing in csi_J(), making the code simpler in the end.
Reported-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Matthew Whitehead <tedheadster@gmail.com>
Fixes: 4b4ecd9cb8 ("vt: Perform safe console erase only once")
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use pci_iomap instead of ioremap_nocache in nozomi_card_init(). This
is a cleaner way to do PCI MMIO (performs additional checks) and
allows to drop the manual call to pci_resource_start.
pci_iomap relies on ioremap for MMIO and thus has uncached behavior.
Signed-off-by: Hugo Lefeuvre <hle@owl.eu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ISA support in this driver is horribly outdated and the last
driver that passes a NULL dev argument to the DMA mapping routines.
Drop the support, if someone wants to go through the work of converting
it to a proper isa_driver we can resurrect it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial_pci_is_blacklisted() is very similar to pci_match_id() implementation.
Replace it with the latter.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small tty and serial fixes for 5.0-rc6.
Nothing huge, just a few small fixes for reported issues. The speakup
fix is in here as it is a tty operation issue.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXF09tg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yniTwCfQ9Owr8XFJRW7QC0BPKDjohqewA8AniK/9YJ/
l73fnvsXELOX9eE/ixCx
=0ylh
-----END PGP SIGNATURE-----
Merge tag 'tty-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty and serial fixes for 5.0-rc6.
Nothing huge, just a few small fixes for reported issues. The speakup
fix is in here as it is a tty operation issue.
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: fix race between flush_to_ldisc and tty_open
staging: speakup: fix tty-operation NULL derefs
serial: sh-sci: Do not free irqs that have already been freed
serial: 8250_pci: Make PCI class test non fatal
tty: serial: 8250_mtk: Fix potential NULL pointer dereference
The MODE1 register bits have different values for different ICs.
This patch corrects the initial setting of this register in accordance
with the datasheets, which will allow you to get the expected values
when debugging the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AUDIT_TTY records were logged as seperate events from their syscall
records. Join them so they are logged as the single event that they
are.
Please see the github issue
https://github.com/linux-audit/audit-kernel/issues/106
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
This patch set contains a handful of mostly-independent patches:
* A patch that causes our port to respect TIF_NEED_RESCHED, which fixes
CONFIG_PREEMPT=y kernels.
* A fix to avoid double-put on OF nodes.
* Fix a misspelling of target in our Kconfig.
* Generic PCIe is enabled in our defconfig.
* A fix to our SBI early console to properly handle line endings.
* A fix such that max_low_pfn is counted in PFNs.
* A change to TASK_UNMAPPED_BASE to match what other arches do.
This has passed by standard "boot Fedora" flow.
-----BEGIN PGP SIGNATURE-----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=Z3YY
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Pull RISC-V fixes from Palmer Dabbelt:
"This contains a handful of mostly-independent patches:
- make our port respect TIF_NEED_RESCHED, which fixes
CONFIG_PREEMPT=y kernels
- fix double-put of OF nodes
- fix a misspelling of target in our Kconfig
- generic PCIe is enabled in our defconfig
- fix our SBI early console to properly handle line
endings
- fix max_low_pfn being counted in PFNs
- a change to TASK_UNMAPPED_BASE to match what other
arches do
This has passed my standard 'boot Fedora' flow"
* tag 'riscv-for-linus-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
riscv: Adjust mmap base address at a third of task size
riscv: fixup max_low_pfn with PFN_DOWN.
tty/serial: use uart_console_write in the RISC-V SBL early console
RISC-V: defconfig: Add CRYPTO_DEV_VIRTIO=y
RISC-V: defconfig: Enable Generic PCIE by default
RISC-V: defconfig: Move CONFIG_PCI{,E_XILINX}
RISC-V: Kconfig: fix spelling mistake "traget" -> "target"
RISC-V: asm/page.h: fix spelling mistake "CONFIG_64BITS" -> "CONFIG_64BIT"
RISC-V: fix bad use of of_node_put
RISC-V: Add _TIF_NEED_RESCHED check for kernel thread when CONFIG_PREEMPT=y
Move the Rohm Vendor ID to pci_ids.h instead of defining it in several
drivers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
There still is a race window after the commit b027e2298b
("tty: fix data race between tty_init_dev and flush of buf"),
and we encountered this crash issue if receive_buf call comes
before tty initialization completes in tty_open and
tty->driver_data may be NULL.
CPU0 CPU1
---- ----
tty_open
tty_init_dev
tty_ldisc_unlock
schedule
flush_to_ldisc
receive_buf
tty_port_default_receive_buf
tty_ldisc_receive_buf
n_tty_receive_buf_common
__receive_buf
uart_flush_chars
uart_start
/*tty->driver_data is NULL*/
tty->ops->open
/*init tty->driver_data*/
it can be fixed by extending ldisc semaphore lock in tty_init_dev
to driver_data initialized completely after tty->ops->open(), but
this will lead to get lock on one function and unlock in some other
function, and hard to maintain, so fix this race only by checking
tty->driver_data when receiving, and return if tty->driver_data
is NULL, and n_tty_receive_buf_common maybe calls uart_unthrottle,
so add the same check.
Because the tty layer knows nothing about the driver associated with the
device, the tty layer can not do anything here, it is up to the tty
driver itself to check for this type of race. Fix up the serial driver
to correctly check to see if it is finished binding with the device when
being called, and if not, abort the tty calls.
[Description and problem report and testing from Li RongQing, I rewrote
the patch to be in the serial layer, not in the tty core - gregkh]
Reported-by: Li RongQing <lirongqing@baidu.com>
Tested-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Wang Li <wangli39@baidu.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang warns:
drivers/tty/serial/mps2-uart.c:351:6: warning: logical not is only
applied to the left hand side of this bitwise operator
[-Wlogical-not-parentheses]
if (!mps_port->flags & UART_PORT_COMBINED_IRQ) {
^ ~
drivers/tty/serial/mps2-uart.c:351:6: note: add parentheses after the
'!' to evaluate the bitwise operator first
if (!mps_port->flags & UART_PORT_COMBINED_IRQ) {
^
( )
drivers/tty/serial/mps2-uart.c:351:6: note: add parentheses around left
hand side expression to silence this warning
if (!mps_port->flags & UART_PORT_COMBINED_IRQ) {
^
( )
1 warning generated.
As it was intended for this check to be the inverse of the one at the
bottom of mps2_init_port, add parentheses around the whole conditional.
Fixes: 775ea4ea2f ("serial: mps2-uart: support combined irq")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Vladimir Murzin <vladimir.murzin@arm.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/344
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We increase the default limit for buffer memory allocation by a factor of
10 to 640K to prevent data loss when using fast serial interfaces.
For example when using RS485 without flow-control at speeds of 1Mbit/s
an upwards we've run into problems such as applications being too slow
to read out this buffer (on embedded devices based on imx53 or imx6).
If you want to write transmitted data to a slow SD card and thus have
realtime requirements, this limit can become a problem.
That shouldn't be the case and 640K buffers fix such problems for us.
This value is a maximum limit for allocation only. It has no effect
on systems that currently run fine. When transmission is slow enough
applications and hardware can keep up and increasing this limit
doesn't change anything.
It only _allows_ to allocate more than 2*64K in cases we currently fail to
allocate memory despite having some.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@ginzinger.com>
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a potential NULL pointer dereference in case
alloc_ctrl_packet() fails and returns NULL.
Fixes: 099dc4fb62 ("ipwireless: driver for PC Card 3G/UMTS modem")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turns out that some designs went for implementing only combined
interrupt for rx, tx and overrun, which is currently not supported
by the driver. Support of combined irq is built on top of existent
irq handlers and activated automatically if only single irq was
specified in device tree.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some designs, like MPS3, expose number of virtual serial ports which
already close or exceeds MPS2_MAX_PORTS. Increasing MPS2_MAX_PORTS
would have negative impact (in terms of memory consumption) on tiny
MPS2 platform which, in fact, has only one physically populated UART.
Start with converting existent static port array to idr. As a bonus it
make driver not to fail in case when no alias was specified in device
tree.
Note: there is no need in idr_destroy() because code doesn't unload
since ce87122911 ("serial: mps2-uart: make driver explicitly non-modular")
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty struct holds a pointer to the driver's tty operations so drop
the unnecessary driver dereference when calling tiocmget and tiocmset.
Note that this also makes the calls match the preceding sanity checks as
expected.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since IRQs might be muxed on some parts, we need to pay attention when we
are freeing them.
Otherwise we get the ugly WARNING "Trying to free already-free IRQ 20".
Fixes: 628c534ae7 ("serial: sh-sci: Improve support for separate TEI and DRI interrupts")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As has been reported the National Instruments serial cards have broken
PCI class.
The commit 7d8905d064
("serial: 8250_pci: Enable device after we check black list")
made the PCI class check mandatory for the case when device is listed in
a quirk list.
Make PCI class test non fatal to allow broken card be enumerated.
Fixes: 7d8905d064 ("serial: 8250_pci: Enable device after we check black list")
Cc: stable <stable@vger.kernel.org>
Reported-by: Guan Yung Tseng <guan.yung.tseng@ni.com>
Tested-by: Guan Yung Tseng <guan.yung.tseng@ni.com>
Tested-by: KHUENY.Gerhard <Gerhard.KHUENY@bachmann.info>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a potential NULL pointer dereference in case devm_kzalloc()
fails and returns NULL.
Fix this by adding a NULL check on data->dma
This bug was detected with the help of Coccinelle.
Fixes: 85b5c1dd04 ("serial: 8250-mtk: add uart DMA support")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Tegra Combined UART (TCU) is a mailbox-based mechanism that allows
multiplexing multiple "virtual UARTs" into a single hardware serial
port. The TCU is the primary serial port on Tegra194 devices.
Add a TCU driver utilizing the mailbox framework, as the used mailboxes
are part of Tegra HSP blocks that are already controlled by the Tegra
HSP mailbox driver.
Based on work by Mikko Perttunen <mperttunen@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for probing the 8250_ingenic driver on the
X1000 Soc from Ingenic.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for device tree probing for the Intel
Xscale 8250 variant needed to support device tree on
the Intel IXP4xx platforms.
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add DMA support for 32-bit variant of the LPUART, such as LS1021A.
Signed-off-by: Tomonori Sakita <tomonori.sakita@sord.co.jp>
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By default, the kernel will automatically load the module of any line
dicipline that is asked for. As this sometimes isn't the safest thing
to do, provide a sysctl to disable this feature.
By default, we set this to 'y' as that is the historical way that Linux
has worked, and we do not want to break working systems. But in the
future, perhaps this can default to 'n' to prevent this functionality.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 97f5f0cd8c ("Input: implement SysRq as a separate input
handler") added pr_fmt() definition. It caused a duplicated message
prefix in the sysrq header messages, for example:
[ 177.053931] sysrq: SysRq : Show backtrace of all active CPUs
[ 742.864776] sysrq: SysRq : HELP : loglevel(0-9) reboot(b) crash(c)
Fixes: 97f5f0cd8c ("Input: implement SysRq as a separate input handler")
Signed-off-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sysrq header line is printed with an increased loglevel
to provide users some positive feedback.
The original loglevel is not restored when the sysrq operation
is disabled. This bug was introduced in 2.6.12 (pre-git-history)
by the commit ("Allow admin to enable only some of the Magic-Sysrq
functions").
Signed-off-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The geni set/get_mctrl() functions currently do nothing unless
hardware flow control is enabled. Remove this arbitrary limitation.
Suggested-by: Johan Hovold <johan@kernel.org>
Fixes: 8a8a66a1a1 ("tty: serial: qcom_geni_serial: Add support for flow control")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some tty line disciplines do not have a receive buf callback, so
properly check for that before calling it. If they do not have this
callback, just eat the character quietly, as we can't fail this call.
Reported-by: Jann Horn <jannh@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
csi sequences can contain subparameters delimited by ':' characters. For
now just ignore the whole sequence in this case. Such sequences are used by
more capable terminal implementations with T.416 high color modes or
extended underline rendition attributes.
Also ignore sequences with private use characters '?', '>', '='
and '>' that are not at the initial position.
Signed-off-by: Martin Hostettler <textshell@uchuujin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Various csi sequences contain intermediate characters between the
parameters and the final character. Introduce a additional state that
cleanly ignores these sequences.
This allows the vt to ignore these sequences used by more capable
terminal implementations such as "request mode", etc.
Signed-off-by: Martin Hostettler <textshell@uchuujin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Private sequences can start with '>', '=' and (in theory) '<'.
Implement correct parsing for these. The newly parsable sequences are
cleanly ignored as it is customary with terminal emulators.
This allows the vt to ignore various sequences used by more capable
terminal implementations such as "Secondary Device Attributes",
"Tertiary Device Attributes" and various advanced configuration commands
that don't have dedicated terminfo entries.
Signed-off-by: Martin Hostettler <textshell@uchuujin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vc_ques keeps track if a csi sequence is a private DEC control
function beginning with '?'. Nowadays some private control functions
begin with '>' and '='. Switch the code to instead use a new 3-bit
vc_priv that allows for all private use parameter prefixes.
Signed-off-by: Martin Hostettler <textshell@uchuujin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a plan to build the kernel with -Wimplicit-fallthrough and
these places in the code produced warnings (W=1). Fix them up.
This commit remove the following warning:
drivers/tty/vt/vt.c:2112:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/tty/vt/vt.c:2237:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Restore and document the forced initial POLLPRI event reporting when
poll() is used for the first time. This used to be the implemented
behavior before recent changes. Because of the way poll() is implemented,
this prevents losing an event happening between the last read() and the
first poll() invocation.
Since poll() for /dev/vcs* was not always supported, user space probes
for its availability as follows:
int fd = open("/dev/vcsa", O_RDONLY);
struct pollfd p = { .fd = fd, .events = POLLPRI };
available = (poll(&p, 1, 0) == 1);
Semantically, it makes sense to signal the first event as such even if
it might be spurious. The screen could be modified, and modified back
to its initial state before we get to read it, so users must be prepared
for that anyway.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We use POLLPRI not POLLIN to wait for data with poll() as there is
never any incoming data stream per se. Let's use the same semantic
with fasync() for consistency, including the fact that a vt may go away.
No known user space ever relied on the SIGIO reason so far, let alone
FASYNC, so the risk of breakage is pretty much nonexistent.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When VT_DISALLOCATE is used on a vt, user space waiting with poll() on
the corresponding /dev/vcs device is not awakened. This is now fixed by
returning POLLHUP|POLLERR to user space.
Also, in the normal screen update case, we don't set POLLERR anymore as
POLLPRI alone is a much more logical response in a non-error situation,
saving some confusion on the user space side. The only known user app
making use of poll() on /dev/vcs* is BRLTTY which is known to cope with
that change already, so the risk of breakage is pretty much nonexistent.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The /dev/vcsa* devices have a fixed char-sized header that stores the
screen geometry and cursor location. Let's make sure it doesn't contain
random garbage when those values exceed 255. If ever it becomes necessary
to convey larger screen info to user space then a larger header in the
not-yet-implemented /dev/vcsua* devices should be considered.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
User space using poll() on /dev/vcs devices are not awaken when a
screen size change occurs. Let's fix that.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every invocation of notify_write() and notify_update() is performed
under the console lock, except for one case. Let's fix that.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When kernel messages are printed to the console, they appear blank on
the unicode screen. This is because vt_console_print() is lacking a call
to vc_uniscr_putc(). However the later function assumes vc->vc_x is
always up to date when called, which is not the case here as
vt_console_print() uses it to mark the beginning of the display update.
This patch reworks (and simplifies) vt_console_print() so that vc->vc_x
is always valid and keeps the start of display update in a local variable
instead, which finally allows for adding the missing vc_uniscr_putc()
call.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix __might_sleep warning[1] in tty/n_hdlc.c read due to copy_to_user
call while current is TASK_INTERRUPTIBLE. This is a false positive
since the code path does not depend on current state remaining
TASK_INTERRUPTIBLE. The loop breaks out and sets TASK_RUNNING after
calling copy_to_user.
This patch supresses the warning by setting TASK_RUNNING before calling
copy_to_user.
[1] https://syzkaller.appspot.com/bug?id=17d5de7f1fcab794cb8c40032f893f52de899324
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Reported-by: syzbot <syzbot+c244af085a0159d22879@syzkaller.appspotmail.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: stable <stable@vger.kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Give a better descriptions of what WAKEUP_CHARS represents.
Signed-off-by: Valentin Vidic <Valentin.Vidic@CARNet.hr>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The initialization code of interrupt backoff work might reference NULL
pointer and cause the following crash, if no port was found.
[ 10.017727] CPU 0 Unable to handle kernel paging request at virtual address 000001b0, epc == 807088e0, ra == 8070863c
---- snip ----
[ 11.704470] [<807088e0>] serial8250_register_8250_port+0x318/0x4ac
[ 11.747251] [<80708d74>] serial8250_probe+0x148/0x1c0
[ 11.789301] [<80728450>] platform_drv_probe+0x40/0x94
[ 11.830515] [<807264f8>] really_probe+0xf8/0x318
[ 11.870876] [<80726b7c>] __driver_attach+0x110/0x12c
[ 11.910960] [<80724374>] bus_for_each_dev+0x78/0xcc
[ 11.951134] [<80725958>] bus_add_driver+0x200/0x234
[ 11.989756] [<807273d8>] driver_register+0x84/0x148
[ 12.029832] [<80d72f84>] serial8250_init+0x138/0x198
[ 12.070447] [<80100e6c>] do_one_initcall+0x5c/0x2a0
[ 12.110104] [<80d3a208>] kernel_init_freeable+0x370/0x484
[ 12.150722] [<80a49420>] kernel_init+0x10/0xf8
[ 12.191517] [<8010756c>] ret_from_kernel_thread+0x14/0x1c
This patch makes sure the initialization code can be reached only if a port
is found.
Fixes: 6d7f677a2a ("serial: 8250: Rate limit serial port rx interrupts during input overruns")
Signed-off-by: He Zhe <zhe.he@windriver.com>
Reviewed-by: Darwin Dingel <darwin.dingel@alliedtelesis.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to prepare for adding serdev driver support, let's constify
the use of u8 and unsigned char for n_gsm.
Note that gsm_control_modem() gsm_control_rls() read the data for tty
control characters and then call gsm_control_reply() that allocates a
new reply and copies the data.
Cc: linux-serial@vger.kernel.org
Cc: Alan Cox <alan@llwyncelyn.cymru>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Johan Hovold <johan@kernel.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For supporting serdev drivers, we need to be able to configure n_gsm
from drivers. Let's prepare for that by adding copy_config() and
gsm_config() helper functions by moving the code around a bit.
Let's also unify the comments to keep checkpatch happy while at it.
Cc: linux-serial@vger.kernel.org
Cc: Alan Cox <alan@llwyncelyn.cymru>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Johan Hovold <johan@kernel.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When probing the HSUART, it is put in loopback mode in order to prevent a
potential issue that may happen on RX (Errata HSUART.1).
serial_lpc32xx_startup() moves it out of loopback mode but this is too late
to get the kernel boot messages before userspace opens the device.
Also get out of loopback mode in lpc32xx_hsuart_console_setup().
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250_omap driver uses clock-frequency DT property to obtain functional
clk frequency. This is not ideal as users need to calculate functional
clk frequency offline and populate it in DT.
Therefore add support to obtain functional clock frequency using clk
APIs when clock-frequency DT property is not defined.
Suggested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250_omap is DT only driver so dev->of_node always exists. Drop check
for existence of valid dev->of_node to simplify omap8250_probe().
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At probe, the uart driver tries to get an id from a device tree alias.
When no alias was specified, the driver would return an error and probing
would fail.
Providing an alias for registering a serial device should not be mandatory.
If the device tree does not specify an alias, provide an id from a reserved
range so that the probing can continue.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Loys Ollivier <lollivier@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are 2 tty and serial fixes for 5.0-rc2 that resolve some reported
issues.
The first is a simple serial driver fix for a regression that showed up
in 5.0-rc1. The second one resolves a number of reported issues with
the recent tty locking fixes that went into 5.0-rc1. Lots of people
have tested the second one and say it resolves their issues.
Both have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXDsOzA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl8OACgg3KREaqF3vizmxVr3xzKk2xG7x0An28XJcYA
z95ZRO/BuSATH1kTM36D
=p+SA
-----END PGP SIGNATURE-----
Merge tag 'tty-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are 2 tty and serial fixes for 5.0-rc2 that resolve some reported
issues.
The first is a simple serial driver fix for a regression that showed
up in 5.0-rc1. The second one resolves a number of reported issues
with the recent tty locking fixes that went into 5.0-rc1. Lots of
people have tested the second one and say it resolves their issues.
Both have been in linux-next with no reported issues"
* tag 'tty-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Don't hold ldisc lock in tty_reopen() if ldisc present
serial: lantiq: Do not swap register read/writes
Try to get reference for ldisc during tty_reopen().
If ldisc present, we don't need to do tty_ldisc_reinit() and lock the
write side for line discipline semaphore.
Effectively, it optimizes fast-path for tty_reopen(), but more
importantly it won't interrupt ongoing IO on the tty as no ldisc change
is needed.
Fixes user-visible issue when tty_reopen() interrupted login process for
user with a long password, observed and reported by Lukas.
Fixes: c96cf923a9 ("tty: Don't block on IO when ldisc change is pending")
Fixes: 83d817f410 ("tty: Hold tty_ldisc_lock() during tty_reopen()")
Cc: Jiri Slaby <jslaby@suse.com>
Reported-by: Lukas F. Hartmann <lukas@mntmn.com>
Tested-by: Lukas F. Hartmann <lukas@mntmn.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In RISC-V, the M-mode runtime firmware provide SBI calls for
debug prints. This patch adds earlycon support using RISC-V
SBI console calls. To enable it, just pass "earlycon=sbi" in
kernel parameters.
Signed-off-by: Anup Patel <anup@brainfault.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Use u32 rather than unsigned long for register variables for clarity and
consistency.
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver only supports FIFO mode so setting and checking this variable
is unnecessary. If DMA support is ever added then such checks can be
introduced.
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variables of tx_wm and rx_wm were set to the same define value in
all cases, never updated, and the define was sometimes used
interchangably. Remove the variables/function and use the fixed value.
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A frequent side comment has been to remove the use of writel_relaxed,
readl_relaxed, and mb. This reduces driver complexity and the _relaxed
variants were not known to provide any noticeable performance benefit.
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most RX/TX-specific DMA functions are prefixed with "sci_dma_[rt]x_".
Rename the exceptions to increase consistency.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When submitting a DMA request fails in sci_dma_rx_complete(), the driver
tries to fall back to PIO, but that does not work: no more data will be
received, or the kernel will even crash.
Fix this similar as in (but not identical to) sci_submit_rx():
- On SCIF, PIO cannot take over if any DMA transactions are pending,
hence they must be terminated first.
- All active cookies must be invalidated, else rx_timer_fn() may
trigger a NULL pointer dereference.
- Restarting the port is not needed, as it is already running, but
serial port interrupts must be directed back from the DMA engine to
the CPU.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extract the functionality to direct new serial port interrupts back to
the CPU into its own helper, to prepare for using it from a second
callsite.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cookies and channel pointer for the DMA receive channel are
invalidated in two places, and one more is planned.
Extract this functionality in a common helper.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
spi_register_driver() may fail, so let's pass its return value upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since board support for the CLPS711X platform was removed
(commit 4a56f46a7d ("ARM: clps711x: Remove boards support")),
remove the board support from the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ltq_r32() and ltq_w32() macros use the __raw_readl() and
__raw_writel() functions which do not swap the value to little endian.
On the big endian vrx200 SoC the UART is operated in big endian IO mode,
the readl() and write() functions convert the value to little endian
first and then the driver does not work any more on this SoC.
Currently the vrx200 SoC selects the CONFIG_SWAP_IO_SPACE option,
without this option the serial driver would work, but PCI devices do not
work any more.
This patch makes the driver use the __raw_readl() and __raw_writel()
functions which do not swap the endianness. On big endian system it is
assumed that the device should be access in big endian IO mode and on a
little endian system it would be access in little endian mode.
Fixes: 89b8bd2082 ("serial: lantiq: Use readl/writel instead of ltq_r32/ltq_w32")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit a9ddb575d6
("dmaengine: dw_dmac: Enhance device tree support")
introduces is_private property in uncertain understanding what does it mean.
First of all, documentation defines DMA_PRIVATE capability as
Documentation/crypto/async-tx-api.txt:
The DMA_PRIVATE capability flag is used to tag dma devices that should not be
used by the general-purpose allocator. It can be set at initialization time
if it is known that a channel will always be private. Alternatively,
it is set when dma_request_channel() finds an unused "public" channel.
A couple caveats to note when implementing a driver and consumer:
1/ Once a channel has been privately allocated it will no longer be
considered by the general-purpose allocator even after a call to
dma_release_channel().
2/ Since capabilities are specified at the device level a dma_device with
multiple channels will either have all channels public, or all channels
private.
Documentation/driver-api/dmaengine/provider.rst:
- DMA_PRIVATE
The devices only supports slave transfers, and as such isn't available
for async transfers.
The capability had been introduced by the commit 59b5ec2144
("dmaengine: introduce dma_request_channel and private channels")
and some code didn't changed from that times ever.
Taking into consideration above and the fact that on all known platforms
Synopsys DesignWare DMA engine is attached to serve slave transfers,
the DMA_PRIVATE capability must be enabled for this device unconditionally.
Otherwise, as rightfully noticed in drivers/dma/at_xdmac.c:
/*
* Without DMA_PRIVATE the driver is not able to allocate more than
* one channel, second allocation fails in private_candidate.
*/
because of of a caveats mentioned in above documentation excerpts.
So, remove conditional around DMA_PRIVATE followed by removal leftovers.
If someone wonders, DMA_PRIVATE can be not used if and only if the all channels
of the DMA controller are supposed to serve memory-to-memory like operations.
For example, EP93xx has two controllers, one of which can only perform
memory-to-memory transfers
Note, this change doesn't affect dmatest to be able to test such controllers.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> (maintainer:SERIAL DRIVERS)
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
A few updates that we merged late but are low risk for regressions for
other platforms (and a few other straggling patches):
- I mis-tagged the 'drivers' branch, and missed 3 patches. Merged in
here. They're for a driver for the PL353 SRAM controller and a build
fix for the qualcomm scm driver.
- A new platform, RDA Micro RDA8810PL (Cortex-A5 w/ integrated Vivante
GPU, 256MB RAM, Wifi). This includes some acked platform-specific
drivers (serial, etc). This also include DTs for two boards with this
SoC, OrangePi 2G and OrangePi i86.
- i.MX8 is another new platform (NXP, 4x Cortex-A53 + Cortex-M4, 4K
video playback offload). This is the first i.MX 64-bit SoC.
- Some minor updates to Samsung boards (adding a few peripherals in
DTs).
- Small rework for SMP bootup on STi platforms.
- A couple of TEE driver fixes.
- A couple of new config options (bcm2835 thermal, Uniphier MDMAC)
enabled in defconfigs.
-----BEGIN PGP SIGNATURE-----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=qgZw
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull more ARM SoC updates from Olof Johansson:
"A few updates that we merged late but are low risk for regressions for
other platforms (and a few other straggling patches):
- I mis-tagged the 'drivers' branch, and missed 3 patches. Merged in
here. They're for a driver for the PL353 SRAM controller and a
build fix for the qualcomm scm driver.
- A new platform, RDA Micro RDA8810PL (Cortex-A5 w/ integrated
Vivante GPU, 256MB RAM, Wifi). This includes some acked
platform-specific drivers (serial, etc). This also include DTs for
two boards with this SoC, OrangePi 2G and OrangePi i86.
- i.MX8 is another new platform (NXP, 4x Cortex-A53 + Cortex-M4, 4K
video playback offload). This is the first i.MX 64-bit SoC.
- Some minor updates to Samsung boards (adding a few peripherals in
DTs).
- Small rework for SMP bootup on STi platforms.
- A couple of TEE driver fixes.
- A couple of new config options (bcm2835 thermal, Uniphier MDMAC)
enabled in defconfigs"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
ARM: multi_v7_defconfig: enable CONFIG_UNIPHIER_MDMAC
arm64: defconfig: Re-enable bcm2835-thermal driver
MAINTAINERS: Add entry for RDA Micro SoC architecture
tty: serial: Add RDA8810PL UART driver
ARM: dts: rda8810pl: Add interrupt support for UART
dt-bindings: serial: Document RDA Micro UART
ARM: dts: rda8810pl: Add timer support
ARM: dts: Add devicetree for OrangePi i96 board
ARM: dts: Add devicetree for OrangePi 2G IoT board
ARM: dts: Add devicetree for RDA8810PL SoC
ARM: Prepare RDA8810PL SoC
dt-bindings: arm: Document RDA8810PL and reference boards
dt-bindings: Add RDA Micro vendor prefix
ARM: sti: remove pen_release and boot_lock
arm64: dts: exynos: Add Bluetooth chip to TM2(e) boards
arm64: dts: imx8mq-evk: enable watchdog
arm64: dts: imx8mq: add watchdog devices
MAINTAINERS: add i.MX8 DT path to i.MX architecture
arm64: add support for i.MX8M EVK board
arm64: add basic DTS for i.MX8MQ
...
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the large TTY/Serial driver set of patches for 4.21-rc1.
A number of small serial driver changes along with some good tty core
fixes for long-reported issues with locking. There is also a new
console font added to the tree, for high-res screens, so that should be
helpful for many.
The last patch in the series is a revert of an older one in the tree, it
came late but it resolves a reported issue that linux-next was having
for some people.
Full details are in the shortlog, and all of these, with the exception
of the revert, have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iGwEABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXCY+1w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl9PgCXckFuSe66uNMzdq2jsVgLKtMR+ACbBzrLQeMZ
LU8UpaVqDJrrPxVURGY=
=a/Xk
-----END PGP SIGNATURE-----
Merge tag 'tty-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the large TTY/Serial driver set of patches for 4.21-rc1.
A number of small serial driver changes along with some good tty core
fixes for long-reported issues with locking. There is also a new
console font added to the tree, for high-res screens, so that should
be helpful for many.
The last patch in the series is a revert of an older one in the tree,
it came late but it resolves a reported issue that linux-next was
having for some people.
Full details are in the shortlog, and all of these, with the exception
of the revert, have been in linux-next for a while with no reported
issues"
* tag 'tty-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (85 commits)
Revert "serial: 8250: Default SERIAL_OF_PLATFORM to SERIAL_8250"
serial: sccnxp: Allow to use non-standard baud rates
serial: sccnxp: Adds a delay between sequential read/write cycles
tty: serial: qcom_geni_serial: Fix UART hang
tty: serial: qcom_geni_serial: Fix wrap around of TX buffer
serial: max310x: Fix tx_empty() callback
dt-bindings: serial: sh-sci: Document r8a774c0 bindings
dt-bindings: serial: sh-sci: Document r8a774a1 bindings
Fonts: New Terminus large console font
dt-bindings: serial: lpuart: add imx8qxp compatible string
serial: uartps: Fix interrupt mask issue to handle the RX interrupts properly
serial: uartps: Fix error path when alloc failed
serial: uartps: Check if the device is a console
serial: uartps: Add the device_init_wakeup
tty: serial: samsung: Increase maximum baudrate
tty: serial: samsung: Properly set flags in autoCTS mode
tty: Use of_node_name_{eq,prefix} for node name comparisons
tty/serial: do not free trasnmit buffer page under port lock
serial: 8250: Rate limit serial port rx interrupts during input overruns
dt-bindings: serial: 8250: Add rate limit for serial port input overruns
...
-----BEGIN PGP SIGNATURE-----
iQJIBAABCAAyFiEES0KozwfymdVUl37v6iDy2pc3iXMFAlwhAwIUHHBhdWxAcGF1
bC1tb29yZS5jb20ACgkQ6iDy2pc3iXNl1w/+PKsewN5VkmmfibIxZ+iZwe1KGB+L
iOwkdHDkG1Bae5A7TBdbKMbHq0FdhaiDXAIFrfunBG/tbgBF9O0056edekR4rRLp
ReGQVNpGMggiATyVKrc3vi+4+UYQqtS6N7Y8q+mMMX/hVeeESXrTAZdgxSWwsZAX
LbYwXXYUyupLvelpkpakE6VPZEcatcYWrVK/vFKLkTt2jLLlLPtanbMf0B71TULi
5EZSVBYWS71a6yvrrYcVDDZjgot31nVQfX4EIqE6CVcXLuL9vqbZBGKZh+iAGbjs
UdKgaQMZ/eJ4CRYDJca0Bnba3n1AKO4uNssY0nrMW4s/inDPrJnMZ0kgGWfayE3d
QR96aHEP5W3SZoiJCUlYm8a4JFfndYKn4YBvqjvLgIkbd784/rvI+sNGM9BF1DNP
f05frIJVHLNO3sECKWMmQyMGWGglj7bLsjtKrai5UQReyFLpM/q/Lh3J1IHZ9KZq
YWFTA4G0rg7x2bdEB4Qh/SaLOOHW7uyQ7IJCYfzSKsZCIO++RqCQoArxiKRE6++C
hv0UG6NGb6Z6a+k1JSzlxCXPmcui0zow7aqEpZSl/9kiYzkLpBITha/ERP7at5M2
W3JVNfQNn6kPtZFgmNuP7rNE9Yn6jnbIdks0nsi/J/4KUr/p2Mfc5LamyTj1unk6
xf7S+xmOFKHAc2s=
=PCHx
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20181224' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit updates from Paul Moore:
"In the finest of holiday of traditions, I have a number of gifts to
share today. While most of them are re-gifts from others, unlike the
typical re-gift, these are things you will want in and around your
tree; I promise.
This pull request is perhaps a bit larger than our typical PR, but
most of it comes from Jan's rework of audit's fanotify code; a very
welcome improvement. We ran this through our normal regression tests,
as well as some newly created stress tests and everything looks good.
Richard added a few patches, mostly cleaning up a few things and and
shortening some of the audit records that we send to userspace; a
change the userspace folks are quite happy about.
Finally YueHaibing and I kick in a few patches to simplify things a
bit and make the code less prone to errors.
Lastly, I want to say thanks one more time to everyone who has
contributed patches, testing, and code reviews for the audit subsystem
over the past year. The project is what it is due to your help and
contributions - thank you"
* tag 'audit-pr-20181224' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit: (22 commits)
audit: remove duplicated include from audit.c
audit: shorten PATH cap values when zero
audit: use current whenever possible
audit: minimize our use of audit_log_format()
audit: remove WATCH and TREE config options
audit: use session_info helper
audit: localize audit_log_session_info prototype
audit: Use 'mark' name for fsnotify_mark variables
audit: Replace chunk attached to mark instead of replacing mark
audit: Simplify locking around untag_chunk()
audit: Drop all unused chunk nodes during deletion
audit: Guarantee forward progress of chunk untagging
audit: Allocate fsnotify mark independently of chunk
audit: Provide helper for dropping mark's chunk reference
audit: Remove pointless check in insert_hash()
audit: Factor out chunk replacement code
audit: Make hash table insertion safe against concurrent lookups
audit: Embed key into chunk
audit: Fix possible tagging failures
audit: Fix possible spurious -ENOSPC error
...
This reverts commit 6d11023c34.
It causes issues with Guenter's test systems and since there seems to
not be any agreement about _why_ this is a problem, but reverting it
fixes things, let's revert until the root cause is found.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull sparc fixes from David Miller:
"Just some small fixes here and there, and a refcount leak in a serial
driver, nothing serious"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
serial/sunsu: fix refcount leak
sparc: Set "ARCH: sunxx" information on the same line
sparc: vdso: Drop implicit common-page-size linker flag
The function of_find_node_by_path() acquires a reference to the node
returned by it and that reference needs to be dropped by its caller.
su_get_type() doesn't do that. The match node are used as an identifier
to compare against the current node, so we can directly drop the refcount
after getting the node from the path as it is not used as pointer.
Fix this by use a single variable and drop the refcount right after
of_find_node_by_path().
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the use of non-standard baud rates.
For these purposes, we use the built-in timer/counter.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a delay between sequential read/write cycles,
to ensure the required minimum inactive time (tRWD). A time value
from the datasheet has been added for each type of supported chips.
The “inline” compiler attribute has been removed from the
read/write functions, simply allow the compiler to control this.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a serial console write occured while a UART transmit command was
waiting for a done signal then no further data would be sent until
something new kicked the system into gear. If there is already data
waiting in the circular buffer we must re-enable the tx watermark so we
receive the expected interrupts.
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before commit a1fee899e5 ("tty: serial: qcom_geni_serial: Fix
softlock") the size of TX transfers was limited to the TX FIFO size,
and wrap arounds of the UART circular buffer were split into two
transfers. With the commit wrap around are allowed within a transfer.
The TX FIFO of the geni serial port uses a word size of 4 bytes. In
case of a circular buffer wrap within a transfer the driver currently
may write an incomplete word to the FIFO, with some bytes containing
data from the circular buffer and others being zero. Since the
transfer isn't completed yet the zero bytes are sent as if they were
actual data.
Handle wrap arounds of the TX buffer properly and ensure that words
written to the TX FIFO always contain valid data (unless the transfer
is completed).
Fixes: a1fee899e5 ("tty: serial: qcom_geni_serial: Fix softlock")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Tested-by: Ryan Case <ryandcase@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function max310x_tx_empty() accesses the IRQSTS register, which is
cleared by IC when reading, so if there is an interrupt status, we
will lose it. This patch implement the transmitter check only by
the current FIFO level.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch Correct the RX interrupt mask value to handle the
RX interrupts properly.
Fixes: c8dbdc842d ("serial: xuartps: Rewrite the interrupt handling logic")
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When cdns_uart_console allocation failed there is a need to also clear
ID from ID list.
Fixes: ae1cca3fa3 ("serial: uartps: Change uart ID port allocation")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While checking for console_suspend_enabled also check if the
device is a console.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialise the device wakeup.
The device_init_wakeup is needed for the wakeup to work by default.
Uart can be configured as the primary wakeup source so it is good to
enable wakeup by default.
The same functionality is enabled also by 8250_omap, atmel_serial,
omap-serial and stm32-usart.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f6aa5beb45 ("serial: 8250: Fix clearing FIFOs in RS485 mode
again") makes a change to FIFO clearing code which its commit message
suggests was intended to be specific to use with RS485 mode, however:
1) The change made does not just affect __do_stop_tx_rs485(), it also
affects other uses of serial8250_clear_fifos() including paths for
starting up, shutting down or auto-configuring a port regardless of
whether it's an RS485 port or not.
2) It makes the assumption that resetting the FIFOs is a no-op when
FIFOs are disabled, and as such it checks for this case & explicitly
avoids setting the FIFO reset bits when the FIFO enable bit is
clear. A reading of the PC16550D manual would suggest that this is
OK since the FIFO should automatically be reset if it is later
enabled, but we support many 16550-compatible devices and have never
required this auto-reset behaviour for at least the whole git era.
Starting to rely on it now seems risky, offers no benefit, and
indeed breaks at least the Ingenic JZ4780's UARTs which reads
garbage when the RX FIFO is enabled if we don't explicitly reset it.
3) By only resetting the FIFOs if they're enabled, the behaviour of
serial8250_do_startup() during boot now depends on what the value of
FCR is before the 8250 driver is probed. This in itself seems
questionable and leaves us with FCR=0 & no FIFO reset if the UART
was used by 8250_early, otherwise it depends upon what the
bootloader left behind.
4) Although the naming of serial8250_clear_fifos() may be unclear, it
is clear that callers of it expect that it will disable FIFOs. Both
serial8250_do_startup() & serial8250_do_shutdown() contain comments
to that effect, and other callers explicitly re-enable the FIFOs
after calling serial8250_clear_fifos(). The premise of that patch
that disabling the FIFOs is incorrect therefore seems wrong.
For these reasons, this reverts commit f6aa5beb45 ("serial: 8250: Fix
clearing FIFOs in RS485 mode again").
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: f6aa5beb45 ("serial: 8250: Fix clearing FIFOs in RS485 mode again").
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Daniel Jedrychowski <avistel@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: linux-mips@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Cc: stable <stable@vger.kernel.org> # 4.10+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver can be used to communicate with Bluetooth chip in high-speed
UART mode, so increase the maximum baudrate to 3Mbps.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
[mszyprow: rephrased commit message]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 391f93f2ec ("serial: core: Rework hw-assited flow control support")
has changed the way the autoCTS mode is handled.
According to that change, serial drivers which enable H/W autoCTS mode must
set UPSTAT_AUTOCTS to prevent the serial core from inadvertently disabling
TX. This patch adds proper handling of UPSTAT_AUTOCTS flag.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
[mszyprow: rephrased commit message]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
For hvc, the code can also be simplified by using of_stdout pointer
instead of searching again for the stdout node.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-serial@vger.kernel.org
Cc: sparclinux@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LKP has hit yet another circular locking dependency between uart
console drivers and debugobjects [1]:
CPU0 CPU1
rhltable_init()
__init_work()
debug_object_init
uart_shutdown() /* db->lock */
/* uart_port->lock */ debug_print_object()
free_page() printk()
call_console_drivers()
debug_check_no_obj_freed() /* uart_port->lock */
/* db->lock */
debug_print_object()
So there are two dependency chains:
uart_port->lock -> db->lock
And
db->lock -> uart_port->lock
This particular circular locking dependency can be addressed in several
ways:
a) One way would be to move debug_print_object() out of db->lock scope
and, thus, break the db->lock -> uart_port->lock chain.
b) Another one would be to free() transmit buffer page out of db->lock
in UART code; which is what this patch does.
It makes sense to apply a) and b) independently: there are too many things
going on behind free(), none of which depend on uart_port->lock.
The patch fixes transmit buffer page free() in uart_shutdown() and,
additionally, in uart_port_startup() (as was suggested by Dmitry Safonov).
[1] https://lore.kernel.org/lkml/20181211091154.GL23332@shao2-debian/T/#u
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Waiman Long <longman@redhat.com>
Cc: Dmitry Safonov <dima@arista.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port gets faulty or gets flooded with inputs, its interrupt
handler starts to work double time to get the characters to the workqueue
for the tty layer to handle them. When this busy time on the serial/tty
subsystem happens during boot, where it is also busy on the userspace
trying to initialise, some processes can continuously get preempted
and will be on hold until the interrupts subside.
The fix is to backoff on processing received characters for a specified
amount of time when an input overrun is seen (received a new character
before the previous one is processed). This only stops receive and will
continue to transmit characters to serial port. After the backoff period
is done, it receive will be re-enabled. This is optional and will only
be enabled by setting 'overrun-throttle-ms' in the dts.
Signed-off-by: Darwin Dingel <darwin.dingel@alliedtelesis.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable M_TX_FIFO_WATERMARK_EN after we've sent all data for a given
transaction so we don't continue to receive a flurry of free space
interrupts while waiting for the M_CMD_DONE notification. Re-enable the
watermark when establishing the next transaction.
Also clear the watermark interrupt after filling the FIFO so we do not
receive notification again prior to actually having free space.
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On (H)SCIF, sci_submit_rx() is called in the receive interrupt handler.
Hence if DMA submission fails, the interrupt handler should resume
handling reception using PIO, else no more data is received.
Make sci_submit_rx() return an error indicator, so the receive interrupt
handler can act appropriately.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When falling back to PIO, active_rx must be set to a different value
than cookie_rx[i], else sci_dma_rx_find_active() will incorrectly find a
match, leading to a NULL pointer dereference in rx_timer_fn() later.
Use zero instead, which is the same value as after driver
initialization.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some callers of sci_submit_rx() hold the port spinlock, others don't.
During fallback to PIO, the driver needs to obtain the port spinlock.
If the lock was already held, spinlock recursion is detected, causing a
deadlock: BUG: spinlock recursion on CPU#0.
Fix this by adding a flag parameter to sci_submit_rx() for the caller to
indicate the port spinlock is already held, so spinlock recursion can be
avoided.
Move the spin_lock_irqsave() up, so all DMA disable steps are protected,
which is safe as the recently introduced dmaengine_terminate_async() can
be called in atomic context.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are three small tty driver fixes for 4.20-rc6
Nothing major, just some bug fixes for reported issues. Full details
are in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXAz36A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymYQgCgqA04cNFcelv38uoh9I1+AtOCRtEAnA64BAPe
HSAR9D0dbU2kb7vmIHg8
=vppK
-----END PGP SIGNATURE-----
Merge tag 'tty-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty driver fixes from Greg KH:
"Here are three small tty driver fixes for 4.20-rc6
Nothing major, just some bug fixes for reported issues. Full details
are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
kgdboc: fix KASAN global-out-of-bounds bug in param_set_kgdboc_var()
tty: serial: 8250_mtk: always resume the device in probe.
tty: do not set TTY_IO_ERROR flag if console port
Here are some small USB fixes for 4.20-rc6
The "largest" here are some xhci fixes for reported issues. Also here
is a USB core fix, some quirk additions, and a usb-serial fix which
required the export of one of the tty layer's functions to prevent code
duplication. The tty maintainer agreed with this change.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXAz3WA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl+mwCgox0WZiO3qfnpQsIrJ5gJFCTrcmMAoMBC5jDf
e81bwzu507PcqvEXh+rg
=giw6
-----END PGP SIGNATURE-----
Merge tag 'usb-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 4.20-rc6
The "largest" here are some xhci fixes for reported issues. Also here
is a USB core fix, some quirk additions, and a usb-serial fix which
required the export of one of the tty layer's functions to prevent
code duplication. The tty maintainer agreed with this change.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: Prevent U1/U2 link pm states if exit latency is too long
xhci: workaround CSS timeout on AMD SNPS 3.0 xHC
USB: check usb_get_extra_descriptor for proper size
USB: serial: console: fix reported terminal settings
usb: quirk: add no-LPM quirk on SanDisk Ultra Flair device
USB: Fix invalid-free bug in port_over_current_notify()
usb: appledisplay: Add 27" Apple Cinema Display
This patch is trying to fix KE issue due to
"BUG: KASAN: global-out-of-bounds in param_set_kgdboc_var+0x194/0x198"
reported by Syzkaller scan."
[26364:syz-executor0][name:report8t]BUG: KASAN: global-out-of-bounds in param_set_kgdboc_var+0x194/0x198
[26364:syz-executor0][name:report&]Read of size 1 at addr ffffff900e44f95f by task syz-executor0/26364
[26364:syz-executor0][name:report&]
[26364:syz-executor0]CPU: 7 PID: 26364 Comm: syz-executor0 Tainted: G W 0
[26364:syz-executor0]Call trace:
[26364:syz-executor0][<ffffff9008095cf8>] dump_bacIctrace+Ox0/0x470
[26364:syz-executor0][<ffffff9008096de0>] show_stack+0x20/0x30
[26364:syz-executor0][<ffffff90089cc9c8>] dump_stack+Oxd8/0x128
[26364:syz-executor0][<ffffff90084edb38>] print_address_description +0x80/0x4a8
[26364:syz-executor0][<ffffff90084ee270>] kasan_report+Ox178/0x390
[26364:syz-executor0][<ffffff90084ee4a0>] _asan_report_loadi_noabort+Ox18/0x20
[26364:syz-executor0][<ffffff9008b092ac>] param_set_kgdboc_var+Ox194/0x198
[26364:syz-executor0][<ffffff900813af64>] param_attr_store+Ox14c/0x270
[26364:syz-executor0][<ffffff90081394c8>] module_attr_store+0x60/0x90
[26364:syz-executor0][<ffffff90086690c0>] sysfs_kl_write+Ox100/0x158
[26364:syz-executor0][<ffffff9008666d84>] kernfs_fop_write+0x27c/0x3a8
[26364:syz-executor0][<ffffff9008508264>] do_loop_readv_writev+0x114/0x1b0
[26364:syz-executor0][<ffffff9008509ac8>] do_readv_writev+0x4f8/0x5e0
[26364:syz-executor0][<ffffff9008509ce4>] vfs_writev+0x7c/Oxb8
[26364:syz-executor0][<ffffff900850ba64>] SyS_writev+Oxcc/0x208
[26364:syz-executor0][<ffffff90080883f0>] elO_svc_naked +0x24/0x28
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:report&]The buggy address belongs to the variable:
[26364:syz-executor0][name:report&] kgdb_tty_line+Ox3f/0x40
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:report&]Memory state around the buggy address:
[26364:syz-executor0] ffffff900e44f800: 00 00 00 00 00 04 fa fa fa fa fa fa 00 fa fa fa
[26364:syz-executor0] ffffff900e44f880: fa fa fa fa 00 fa fa fa fa fa fa fa 00 fa fa fa
[26364:syz-executor0]> ffffff900e44f900: fa fa fa fa 04 fa fa fa fa fa fa fa 00 00 00 00
[26364:syz-executor0][name:report&] ^
[26364:syz-executor0] ffffff900e44f980: 00 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
[26364:syz-executor0] ffffff900e44fa00: 04 fa fa fa fa fa fa fa 00 fa fa fa fa fa fa fa
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:panic&]Disabling lock debugging due to kernel taint
[26364:syz-executor0]------------[cut here]------------
After checking the source code, we've found there might be an out-of-bounds
access to "config[len - 1]" array when the variable "len" is zero.
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit eca42d4cf3.
During review it was rejected, so drop it from the tree.
Cc: Rajan Vaja <RAJANV@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It seems like when ldsem_down_read() fails with timeout, it misses
update for sem->wait_readers. By that reason, when writer finally
releases write end of the semaphore __ldsem_wake_readers() does adjust
sem->count with wrong value:
sem->wait_readers * (LDSEM_ACTIVE_BIAS - LDSEM_WAIT_BIAS)
I.e, if update comes with 1 missed wait_readers decrement, sem->count
will be 0x100000001 which means that there is active reader and it'll
make any further writer to fail in acquiring the semaphore.
It looks like, this is a dead-code, because ldsem_down_read() is never
called with timeout different than MAX_SCHEDULE_TIMEOUT, so it might be
worth to delete timeout parameter and error path fall-back..
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure under CONFIG_LOCKDEP that each change to line discipline
is done with held write semaphor.
Otherwise potential reader will have a good time dereferencing
incomplete/uninitialized ldisc.
An exception here is tty_ldisc_open(), as it's called without ldisc_sem
locked by tty_init_dev() => tty_ldisc_setup() for the tty->link.
It seem valid as tty_init_dev() will call tty_driver_install_tty()
which will find ops->install(). Install will establish tty->link in
pty_common_install(), just after allocation of slave tty with
alloc_tty_struct(). So, no one should have a reference to slave pty yet.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some reason ldsem has its own lockdep wrappers, make them go away.
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There might be situations where tty_ldisc_lock() has blocked, but there
is already IO on tty and it prevents line discipline changes.
It might theoretically turn into dead-lock.
Basically, provide more priority to pending tty_ldisc_lock() than to
servicing reads/writes over tty.
User-visible issue was reported by Mikulas where on pa-risc with
Debian 5 reboot took either 80 seconds, 3 minutes or 3:25 after proper
locking in tty_reopen().
Cc: Jiri Slaby <jslaby@suse.com>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_ldisc_reinit() doesn't race with neither tty_ldisc_hangup()
nor set_ldisc() nor tty_ldisc_release() as they use tty lock.
But it races with anyone who expects line discipline to be the same
after hoding read semaphore in tty_ldisc_ref().
We've seen the following crash on v4.9.108 stable:
BUG: unable to handle kernel paging request at 0000000000002260
IP: [..] n_tty_receive_buf_common+0x5f/0x86d
Workqueue: events_unbound flush_to_ldisc
Call Trace:
[..] n_tty_receive_buf2
[..] tty_ldisc_receive_buf
[..] flush_to_ldisc
[..] process_one_work
[..] worker_thread
[..] kthread
[..] ret_from_fork
tty_ldisc_reinit() should be called with ldisc_sem hold for writing,
which will protect any reader against line discipline changes.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: stable@vger.kernel.org # b027e2298b ("tty: fix data race between tty_init_dev and flush of buf")
Reviewed-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: syzbot+3aa9784721dfb90e984d@syzkaller.appspotmail.com
Tested-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Tested-by: Tycho Andersen <tycho@tycho.ws>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ldsem_down_read() will sleep if there is pending writer in the queue.
If the writer times out, readers in the queue should be woken up,
otherwise they may miss a chance to acquire the semaphore until the last
active reader will do ldsem_up_read().
There was a couple of reports where there was one active reader and
other readers soft locked up:
Showing all locks held in the system:
2 locks held by khungtaskd/17:
#0: (rcu_read_lock){......}, at: watchdog+0x124/0x6d1
#1: (tasklist_lock){.+.+..}, at: debug_show_all_locks+0x72/0x2d3
2 locks held by askfirst/123:
#0: (&tty->ldisc_sem){.+.+.+}, at: ldsem_down_read+0x46/0x58
#1: (&ldata->atomic_read_lock){+.+...}, at: n_tty_read+0x115/0xbe4
Prevent readers wait for active readers to release ldisc semaphore.
Link: lkml.kernel.org/r/20171121132855.ajdv4k6swzhvktl6@wfg-t540p.sh.intel.com
Link: lkml.kernel.org/r/20180907045041.GF1110@shao2-debian
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sysrq_do_reset() is called in softirq context, so it cannot call
sync() directly. Instead, call orderly_reboot(), which creates a work
item to run /sbin/reboot, or do emergency_sync and restart if the
command fails.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_register_8250_port calls uart_config_port, which calls
config_port on the port before it tries to power on the port. So we need
the port to be on before calling serial8250_register_8250_port. Change
the code to always do a runtime resume in probe before registering port,
and always do a runtime suspend in remove.
This basically reverts the change in commit 68e5fc4a25 ("tty: serial:
8250_mtk: use pm_runtime callbacks for enabling"), but still use
pm_runtime callbacks.
Fixes: 68e5fc4a25 ("tty: serial: 8250_mtk: use pm_runtime callbacks for enabling")
Signed-off-by: Peter Shih <pihsun@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB-serial console implementation has never reported the actual
terminal settings used. Despite storing the corresponding cflags in its
struct console, these were never honoured on later tty open() where the
tty termios would be left initialised to the driver defaults.
Unlike the serial console implementation, the USB-serial code calls
subdriver open() already at console setup. While calling set_termios()
and write() before open() looks like it could work for some USB-serial
drivers, others definitely do not expect this, so modelling this after
serial core is going to be intrusive, if at all possible.
Instead, use a (renamed) tty helper to save the termios data used at
console setup so that the tty termios reflects the actual terminal
settings after a subsequent tty open().
Note that the calls to tty_init_termios() (tty_driver_install()) and
tty_save_termios() are serialised using the disconnect mutex.
This specifically fixes a regression that was triggered by a recent
change adding software flow control to the pl2303 driver: a getty trying
to disable flow control while leaving the baud rate unchanged would now
also set the baud rate to the driver default (prior to the flow-control
change this had been a noop).
Fixes: 7041d9c3f0 ("USB: serial: pl2303: add support for tx xon/xoff flow control")
Cc: stable <stable@vger.kernel.org> # 4.18
Cc: Florian Zumbiehl <florz@florz.de>
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Modify uart register to support DMA function.
Signed-off-by: Long Cheng <long.cheng@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Existing driver checks for alternate clock if devm_clk_get() fails
and returns error code for last clock failure. If xilinx_uartps is
called before clock driver, devm_clk_get() returns -EPROBE_DEFER.
In this case, probe should not check for alternate clock as main
clock is already present in DTS and return -EPROBE_DEFER only.
This patch fixes it by not checking for alternate clock when main
clock get returns -EPROBE_DEFER.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Transfers were being divided into device FIFO sized (64 byte max)
operations which would poll for completion within a spin_lock_irqsave /
spin_unlock_irqrestore block. This both made things slow by waiting for
the FIFO to completely drain before adding further data and would also
result in softlocks on large transmissions.
This patch allows larger transfers with continuous FIFO additions as
space becomes available and removes polling from the interrupt handler.
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 20d8e8611e.
As David Miller points out, it's wrong.
Reported-by: David Miller <davem@davemloft.net>
Cc: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rautkoski Kimmo EXT