* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xen-kbdfront - fix mouse getting stuck after save/restore
Input: estimate number of events per packet
Input: evdev - indicate buffer overrun with SYN_DROPPED
Input: document event types and codes and their intended use
Input: add KEY_IMAGES specifically for AL Image Browser
Input: twl4030_keypad - fix potential NULL dereference in twl4030_kp_probe()
Input: h3600_ts - fix error handling at connect
Input: twl4030_keypad - avoid potential NULL-pointer dereference
This patch allows to set a device name which helps distinguishing several
gpio-keys devices.
Signed-off-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
With this patch you can setup a group of GPIOs representing a specific
position on an EV_ABS axis.
Signed-off-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We should first check whether platform data is NULL or not, before
dereferencing it to get the keymap.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We should return IRQ_NONE from interrupt handler in case keyboard
does not report DATA_AVAIL condition.
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Extend the tca6416 driver to use enable_irq_wake() and disable_irq_wake()
in the suspend/resume hooks.
This makes it possible to wake up from suspend-to-ram using a tca6416 key
on the sh7372 mackerel board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The AT42QT1070 QTouch sensor supports up to 7 keys.
The driver has been tested on Atmel AT91SAM9M10-G45-EK board, and it
should work fine on other platforms.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The MCS50XX series has a HW bug that requires explicit chip power down.
If chip is not powered down before shutting the system down the control
pins (powerup, interrupt) are pulled up and residue current continues
flowing into the chips making them continue consuming power.
Signed-off-by: Heungjun Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This adds support for system-level suspend/resume to the driver.
Signed-off-by: Heungjun Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Enable Runtime PM functionality in OMAP4 driver based on the following
assumptions:
- keyboard controller in wakeup domain so it is always on and power
impact is minimal;
- in OMAP4 the device control is at module/device level and ick/fclk
level control is difficult so cutting of clocks will prevent
interrupts.
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is a general move to convert drivers to use dev_pm_ops rather than
bus specific ops to facilitate core work. Do this conversion for max7359.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is a general move away from bus specific PM operations to using
dev_pm_ops in order to facilicate core improvements. Update lm8323 to
the new model.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add Fn keymap support to allow for internal processing of Fn keys.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - pass touch resolution to clients through input_absinfo
Input: wacom - add 2 Bamboo Pen and touch models
Input: sysrq - ensure sysrq_enabled and __sysrq_enabled are consistent
Input: sparse-keymap - fix KEY_VSW handling in sparse_keymap_setup
Input: tegra-kbc - add tegra keyboard driver
Input: gpio_keys - switch to using request_any_context_irq
Input: serio - allow registered drivers to get status flag
Input: ct82710c - return proper error code for ct82c710_open
Input: bu21013_ts - added regulator support
Input: bu21013_ts - remove duplicate resolution parameters
Input: tnetv107x-ts - don't treat NULL clk as an error
Input: tnetv107x-keypad - don't treat NULL clk as an error
Fix up trivial conflicts in drivers/input/keyboard/Makefile due to
additions of tc3589x/Tegra drivers
This patch adds support for the internal matrix keyboard controller for
Nvidia Tegra platforms.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Reviewed-by: Trilok Soni <tsoni@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The driver does not require hardirq context and can work with threaded
interrupts as well, so let's switch to request_any_context_irq which
will select the context that is available for us.
Signed-off-by: Philippe Langlais <philippe.langlais@stericsson.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We should use IS_ERR() when checking whether clk_get() succeeded or
not since it returns errors by encoding error codes with ERR_PTR().
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The only platform using this driver (mach-aaec2000) is no longer in
the kernel so remove the driver.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (58 commits)
Input: wacom_w8001 - support pen or touch only devices
Input: wacom_w8001 - use __set_bit to set keybits
Input: bu21013_ts - fix misuse of logical operation in place of bitop
Input: i8042 - add Acer Aspire 5100 to the Dritek list
Input: wacom - add support for digitizer in Lenovo W700
Input: psmouse - disable the synaptics extension on OLPC machines
Input: psmouse - fix up Synaptics comment
Input: synaptics - ignore bogus mt packet
Input: synaptics - add multi-finger and semi-mt support
Input: synaptics - report clickpad property
input: mt: Document interface updates
Input: fix double equality sign in uevent
Input: introduce device properties
hid: egalax: Add support for Wetab (726b)
Input: include MT library as source for kerneldoc
MAINTAINERS: Update input-mt entry
hid: egalax: Add support for Samsung NB30 netbook
hid: egalax: Document the new devices in Kconfig
hid: egalax: Add support for Wetab
hid: egalax: Convert to MT slots
...
Fixed up trivial conflict in drivers/input/keyboard/Kconfig
There was a semi-colon missing and it broke the compile.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (243 commits)
omap2: Make OMAP2PLUS select OMAP_DM_TIMER
OMAP4: hwmod data: Fix alignment and end of line in structurefields
OMAP4: hwmod data: Move the DMA structures
OMAP4: hwmod data: Move the smartreflex structures
OMAP4: hwmod data: Fix missing SIDLE_SMART_WKUP in smartreflexsysc
arm: omap: tusb6010: add name for MUSB IRQ
arm: omap: craneboard: Add USB EHCI support
omap2+: Initialize serial port for dynamic remuxing for n8x0
omap2+: Add struct omap_board_data and use it for platform level serial init
omap2+: Allow hwmod state changes to mux pads based on the state changes
omap2+: Add support for hwmod specific muxing of devices
omap2+: Add omap_mux_get_by_name
OMAP2: PM: fix compile error when !CONFIG_SUSPEND
MAINTAINERS: OMAP: hwmod: update hwmod code, data maintainership
OMAP4: Smartreflex framework extensions
OMAP4: hwmod: Add inital data for smartreflex modules.
OMAP4: PM: Program correct init voltages for scalable VDDs
OMAP4: Adding voltage driver support
OMAP4: Register voltage PMIC parameters with the voltage layer
OMAP3: PM: Program correct init voltages for VDD1 and VDD2
...
Fix up trivial conflict in arch/arm/plat-omap/Kconfig
Add support for the keypad controller module found on the
TC3589X devices. This driver default adds the support for
TC35893 device.
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
[Some minor fixups for compilation]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Most keypad drivers make use of the <linux/input/matrix_keypad.h>
defined macros, structures and inline functions.
Convert omap-keypad driver to use those as well, as suggested by a
compile time warning, hardcoded into the OMAP <palt/keypad.h>.
Created against linux-2.6.37-rc5.
Tested on Amstrad Delta.
Compile tested with omap1_defconfig and omap2plus_defconfig shrinked to
board-h4.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Reviewed-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The existing gpio-keys driver can be usable only for GPIO lines with
interrupt support. Several devices have buttons connected to a GPIO
line which is not capable to generate interrupts. This patch adds a
new input driver using the generic GPIO layer and the input-polldev
to support such buttons.
[Ben Gardiner <bengardiner@nanometrics.ca: fold code to use more
of the original gpio_keys infrastructure; cleanups and other
improvements.]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Many of the IBM Terminal keyboards from the 1980s and early 1990s communicate
using a protocol similar, but not identical to the AT keyboard protocol.
(Models known to be like this include 6110344, 6110668, 1390876, 1386887, and
possibly others.)
When the connector is rewired or adapter to an AT-DIN or PS/2 connector, they
can be connected to a standard PC, with three caveats:
a) They can only use scancode set 3; requests to use anything else are
quietly ignored.
b) The AT Command to request Make, Break and Repeat codes is not properly
interpreted.
c) The top function keys on a 122 key keyboard, and the arrow/edit keys in
the middle of the board send non-standard scancodes.
C) is easily taken care of in userspace, by use of setkeycodes
B) can be taken care of by a userspace hack (that makes the kernel complain
in dmesg)
A) is fixable in theory, but on the keyboard i tested on (6110668), it seems
to be detected unoverridably as Set 2, causing userspace oddities that make
it harder to fix C).
Enclosed is a small patch to the kernel that fixes A) and B) in the kernel,
making it much easier to fix C) in userspace. It adds a single kernel
command line parameter that overrides the detection that sets these boards
as set 2, and instead of sending the Make-break-repeat command to the
keyboard, it sends the make-break command, which is properly recognized by
these keyboards. Software level key repeating seems to make up for the lack
of hardware repeat codes perfectly.
Without manually setting the command line parameter (tentatively named
atkbd.terminal), this code has no effect, and the driver works exactly as
before.
See also:
http://www.seasip.info/VintagePC/ibm_1390876.htmlhttp://www.seasip.info/VintagePC/ibm_6110344.htmlhttp://geekhack.org/showwiki.php?title=Island:7306
Signed-off-by: Erika Quinn <erikas.aubade@gmail.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Unify adp5588-gpio and adp5588-keys common header defines (as per Andrew
Morton request). For consistency, move remaining defines and prefix
accordingly.
No functional changes.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (50 commits)
davinci: fix remaining board support after io_pgoffst removal
davinci: mityomapl138: make file local data static
arm/davinci: remove duplicated include
davinci: Initial support for Omapl138-Hawkboard
davinci: MityDSP-L138/MityARM-1808 read MAC address from I2C Prom
davinci: add tnetv107x touchscreen platform device
input: add driver for tnetv107x touchscreen controller
davinci: add keypad config for tnetv107x evm board
davinci: add tnetv107x keypad platform device
input: add driver for tnetv107x on-chip keypad controller
net: davinci_emac: cleanup unused cpdma code
net: davinci_emac: switch to new cpdma layer
net: davinci_emac: separate out cpdma code
net: davinci_emac: cleanup unused mdio emac code
omap: cleanup unused davinci mdio arch code
davinci: cleanup mdio arch code and switch to phy_id
net: davinci_emac: switch to new mdio
omap: add mdio platform devices
davinci: add mdio platform devices
net: davinci_emac: separate out davinci mdio
...
Fix up trivial conflict in drivers/input/keyboard/Kconfig (two entries
added next to each other - one from the davinci merge, one from the
input merge)
KBUILD_MODNAME normalizes "-" to "_". This is non-obvious and results in
the id name for ADP5588 being "adp5588_keys" while the other supported id
is "adp5587-keys". So avoid this define and use an explicit string as the
id name.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Program keyboard controller to generate a wake-up request on events and
on long key presses. It will not generate wake-up requests on timeouts
since driver code does not handle them.
This allows keyboard to wake-up OMAP from suspend.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Remove SYSCONFIG register configuration, omap hwmod framework will
use internal API to modify as required.
Other minor updates:
- Change a variable name from DEF to VAL, this represents a value
- Break line width to 80 characters
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Get mem and irq resources using platform helpers
- platform_get_base
- platform_get_irq
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add support for the keypad controller in the Scroll Key Encoder (SKE)
module on the Nomadik family and the DB8500 SoC.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We should not try to call free_irq() when request_irq() failed.
Reported-by: G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
mach-mmp needs to clear wake event in order to clear the keypad interrupt
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
mach-mmp utilizes pxa27x_keypad code so we need to move header to
platform pxa directory.
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
No need to call input_free_device() after input_unregister_device().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
They've been introduced by 987a6c02 ("Input: switch to input_abs_*()
access functions") and they appear to be some kind of debug left-over.
[Dmitry Torokhov: these are my fault - I added XX prefixes in places where
I wanted to do additional review of the code but failed to actually do
that in these particular instances.]
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an input driver for the keypad on STMPE I/O expanders. This driver
uses the common support provided by the STMPE MFD driver.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xpad - add USB-ID for PL-3601 Xbox 360 pad
Input: cy8ctmg100_ts - signedness bug
Input: elantech - report position also with 3 fingers
Input: elantech - discard the first 2 positions on some firmwares
Input: adxl34x - do not mark device as disabled on startup
Input: gpio_keys - add hooks to enable/disable device
Input: evdev - rearrange ioctl handling
Input: dynamically allocate ABS information
Input: switch to input_abs_*() access functions
Input: add static inline accessors for ABS properties
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
Input: adp5588-keypad - fix NULL dereference in adp5588_gpio_add()
Input: cy8ctmg110 - capacitive touchscreen support
Input: keyboard - also match braille-only keyboards
Input: adp5588-keys - export unused GPIO pins
Input: xpad - add product ID for Hori Fighting Stick EX2
Input: adxl34x - fix leak and use after free
Input: samsung-keypad - Add samsung keypad driver
Input: i8042 - reset keyboard controller wehen resuming from S2R
Input: synaptics - set min/max for finger width
Input: synaptics - only report width on hardware that supports it
Input: evdev - signal that device is writable in evdev_poll()
Input: mousedev - signal that device is writable in mousedev_poll()
Input: change input handlers to use bool when possible
Input: document the MT event slot protocol
Input: introduce MT event slots
Input: usbtouchscreen - implement reset_resume
Input: usbtouchscreen - implement runtime power management
Input: usbtouchscreen - implement basic suspend/resume
Input: Add ATMEL QT602240 touchscreen driver
Input: fix signedness warning in input_set_keycode()
...
Allow platform code to specify callbcks that will be invoked when
input device is opened or closed, allowing, for example, to enable
the device.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Change all call sites in drivers/input to not access the ABS axis
information directly anymore. Make them use the access helpers instead.
Also use input_set_abs_params() when possible.
Did some code refactoring as I was on it.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The kpad structure is assigned to i2c client via i2s_set_clientdata()
at the end of adp5588_probe(), but in adp5588_gpio_add() we tried to
access it (via dev_get_drvdata! which is not nice at all) causing an
oops.
Let's pass pointer to kpad directly into adp5588_gpio_add() and
adp5588_gpio_remove() to avoid accessing driver data before it is
set up.
Also split out building of gpiomap into a separate function to
clear the logic.
Reported-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch allows exporting GPIO pins not used by the keypad itself
to be accessible from elsewhere.
Signed-off-by: Xiaolong Chen <xiao-long.chen@motorola.com>
Signed-off-by: Yuanbo Ye <yuan-bo.ye@motorola.com>
Signed-off-by: Tao Hu <taohu@motorola.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - relax capability ID checks on newer hardware
Input: twl40300-keypad - fix handling of "all ground" rows
Input: gamecon - reference correct pad in gc_psx_command()
Input: gamecon - reference correct input device in NES mode
Input: w90p910_keypad - change platfrom driver name to 'nuc900-kpi'
Input: i8042 - add Gigabyte Spring Peak to dmi_noloop_table
Input: qt2160 - rename kconfig symbol name
This patch adds support for keypad driver running on Samsung cpus. This
driver is tested on GONI and Aquila board using S5PC110 cpu.
[ch.naveen@samsung.com: tested on SMDK6410, SMDKC100, and SMDKV210]
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Nokia RX51 board code (arch/arm/mach-omap2/board-rx51-peripherals.c)
defines a key map for the matrix keypad keyboard. The hardware seems to
use all of the 8 rows and 8 columns of the keypad, although not all
possible locations are used.
The TWL4030 supports keypads with at most 8 rows and 8 columns. Most keys
are defined with a row and column number between 0 and 7, except
KEY(0xff, 2, KEY_F9),
KEY(0xff, 4, KEY_F10),
KEY(0xff, 5, KEY_F11),
which represent keycodes that should be emitted when entire row is
connected to the ground. since the driver handles this case as if we
had an extra column in the key matrix. Unfortunately we do not allocate
enough space and end up owerwriting some random memory.
Reported-and-tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The name of platfrom device was changed and we need to make driver's
name match in order for it to bind to the device.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
drivers/input/keyboard/Kconfig defines QT2160 while the corresponding
Makefile expects CONFIG_KEYBOARD_QT2160 as all other keyboard drivers
do. To keep this Makefile consistent rename the config-token from
CONFIG_QT2160 to CONFIG_KEYBOARD_QT2160.
The various defconfig files are left alone.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This reverts commit 0b28bac5ae.
After adding x86_platform's detection for i8042 controller, we
don't need the force dependency on !X86_MRST any more
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
LKML-Reference: <1278342202-10973-5-git-send-email-feng.tang@intel.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This reverts commit 685afae025.
After adding x86_platform's detection for i8042 controller, we
don't need the force dependency on !X86_MRST any more
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
LKML-Reference: <1278342202-10973-4-git-send-email-feng.tang@intel.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
We reuse the "i" variable later on so if we goto fail3 or fail4
then "i" will be set to the wrong thing and cause a crash.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
gpiolib now has debounce support added in .35, so let's make use of it.
This allows to use hardware GPIO debouncing on some platforms like OMAP.
In case gpiolib debounce setup fails for some GPIO, the driver will fall
back to timer based debouncing, which is what it used before.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A column or row configured as a GPI can be programmed to be part
of the key event table and therefore also capable of generating a
key event interrupt. A key event interrupt caused by a GPI follows
the same process flow as a key event interrupt caused by a key
press. GPIs configured as part of the key event table allow single
key switches and other GPI interrupts to be monitored. As part of
the event table, GPIs are represented by the decimal value 97 (0x61
or 1100001) through the decimal value 114 (0x72 or 1110010). See
table below for GPI event number assignments for rows and columns.
GPI Event Number Assignments for Rows
Row0 Row1 Row2 Row3 Row4 Row5 Row6 Row7
97 98 99 100 101 102 103 104
GPI Event Number Assignments for Cols
Col0 Col1 Col2 Col3 Col4 Col5 Col6 Col7 Col8 Col9
105 106 107 108 109 110 111 112 113 114
Signed-off-by: Xiaolong Chen <xiao-long.chen@motorola.com>
Signed-off-by: Yuanbo Ye <yuan-bo.ye@motorola.com>
Signed-off-by: Tao Hu <taohu@motorola.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some of the recent X86_MRST additions make some "select"s
conditional on X86_MRST but missed some related kconfig symbols,
causing:
drivers/built-in.o: In function `ps2_end_command':
(.text+0x257ab2): undefined reference to `i8042_check_port_owner'
drivers/built-in.o: In function `ps2_end_command':
(.text+0x257ae1): undefined reference to `i8042_unlock_chip'
drivers/built-in.o: In function `ps2_begin_command':
(.text+0x257b40): undefined reference to `i8042_check_port_owner'
drivers/built-in.o: In function `ps2_begin_command':
(.text+0x257b6f): undefined reference to `i8042_lock_chip'
when SERIO_I8042=m, SERIO_LIBPS2=y, KEYBOARD_ATKBD=y.
We need to make i8042 dependant upon !X86_MRST and allow deselecting
atkbd on Moorestown even when !CONFIG_EMBEDDED.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This one adds support of a combined irq source for the whole matrix keypad.
This can be useful if all rows and columns of the keypad are e.g. connected
to a GPIO expander, which only has one interrupt line for all events on
every single GPIO.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
I2C drivers can use the clientdata-pointer to point to private data. As I2C
devices are not really unregistered, but merely detached from their driver, it
used to be the drivers obligation to clear this pointer during remove() or a
failed probe(). As a couple of drivers forgot to do this, it was agreed that it
was cleaner if the i2c-core does this clearance when appropriate, as there is
no guarantee for the lifetime of the clientdata-pointer after remove() anyhow.
This feature was added to the core with commit
e4a7b9b04d to fix the faulty drivers.
As there is no need anymore to clear the clientdata-pointer, remove all current
occurrences in the drivers to simplify the code and prevent confusion.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Moorestown does not have i8042 based keyboard controller, so give
an option to deselect i8042 for non-pc mid.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch implements a simple Keypad driver that functions
as an I2C client. It handles key press events for keys
connected to TCA6416 I2C based IO expander.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not leave dangling client data pointers when unbinding device from the
driver or when binding fails for some reason.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In an embedded system the matrix_keypad driver might be used to
interface with an external control panel and not an actual keyboard.
On the control panel some of the keys could be used to turn on/off
various functions. If key autorepeat is enabled this causes the
function to quickly toggle between the on and off states and makes
operation difficult.
Add an option in the platform-specific data to disable the key
autorepeat.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add ALDI/MEDION netbook E1222 to qurik reset table
Input: ALPS - fix stuck buttons on some touchpads
Input: wm831x-on - convert to use genirq
Input: ads7846 - add wakeup support
Input: appletouch - fix integer overflow issue
Input: ad7877 - increase pen up imeout
Input: ads7846 - add support for AD7843 parts
Input: bf54x-keys - fix system hang when pressing a key
Input: alps - add support for the touchpad on Toshiba Tecra A11-11L
Input: remove BKL, fix input_open_file() locking
Input: serio_raw - remove BKL
Input: mousedev - remove BKL
Input: add driver for TWL4030 vibrator device
Input: enable remote wakeup for PNP i8042 keyboard ports
Input: scancode in get/set_keycodes should be unsigned
Input: i8042 - use platfrom_create_bundle() helper
Input: wacom - merge out and in prox events
Input: gamecon - fix off by one range check
Input: wacom - replace WACOM_PKGLEN_PENABLED
We need to use the nosync version of disable_irq so that we don't hang in
the IRQ handler as we don't ACK the interrupt until later. This used to
work regardless, but at some point, the IRQ behavior changed. Not sure
when exactly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It is not necessary and is over-complicated for IRQ_LOCOMO_KEY to
be a cascaded IRQ of IRQ_LOCOMO_KEY_BASE. Removed and introduced
locomokbd_{open,close} for masking/unmasking of the keyboard IRQ.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Keycodes in 248 - 254 range were reserved for special needs (scrolling)
of atkbd driver. Now that the driver has been switched to use unsigned
short keycodes instead of unsigned char we can release this range back
into pull. We keep code 255 (ATKBD_KEY_NULL) reserved since users may
have been using it to silence keys they do not care about since atkbd
silently drops scancodes mapped to this keycode.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Update the Kconfig entry for the sh_keysc driver to
enable build on SH-Mobile ARM platforms.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add mode 6 support to the sh_keysc driver. Also update the KYOUTDR mask
value to include all 16 register bits.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use bitmaps instead of using 32-bit integers to keep track of the key
states. With this change in place the driver supports key pads with
more than 32 keys.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Update the sh_keysc driver to factor out the register access functions
sh_keysc_read(), sh_keysc_write() together with sh_keysc_level_mode().
This makes the code a bit easier to follow.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Provided that now keyboards on these devices are fully supported by
generic GPIO based matrix keypad driver, mark these hardcoded and
difficult to maintain drivers as deprecated.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Now gpio-keys input driver exports 4 new attributes to userland through
sysfs:
/sys/devices/platform/gpio-keys/keys [ro]
/sys/devices/platform/gpio-keys/switches [ro]
/sys/devices/platform/gpio-keys/disabled_keys [rw]
/sys/devices/platform/gpio-keys/disables_switches [rw]
With these attributes, userland program can read which keys and
switches can be disabled and then disable/enable them as needed.
Keys and switches are exported as stringified bitmap of codes
(keycodes or switch codes). For example keys 15, 89, 100, 101,
102 are exported as: '15,89,100-102'.
Description of the attributes:
keys - bitmap of keys which can be disabled
switches - bitmap of switches which can be disabled
disabled_keys - bitmap of currently disabled keys
(bit 1 means disabled, 0 enabled)
disabled_switches - bitmap of currently disabled switches
(bit 1 means disabled, 0 enabled)
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The IMX family of Application Processors is shipped with a Keypad Port
supported by this driver.
The peripheral can control up to an 8x8 matrix key pad where all the
scanning is done via software. The hardware provides two interrupts:
one for key presses (KDI) and one for all key releases (KRI). There is
also a simple circuit for glitch reduction (said for synchronization)
made by two series of 3 D-latches clocked by the keypad-clock that
stabilize the interrupts sources. KDI and KRI are fired only if the
respective conditions are maintained for at last 4 keypad-clock cycle.
Since those circuits are poor for a correct debounce process (the
keypad-clock frequency is 32K and bounces longer than 94us are not
masked) the driver, when an interrupt arrives, samples the matrix
with a period of 10ms until the readins are stable for
IMX_KEYPAD_SCANS_FOR_STABILITY times (currently set at 3). After
getting stable result appropriate events are sent through the input
stack.
If some keys are maintained pressed, the driver continues to scan
the matrix with a longer period (60ms) to catch possible multiple
key presses without overloading the cpu. This process ends when all
keys are released.
This driver is tested to build in kernel or as a module and follow
the specification of Freescale Application processors:
i.MX25 i.MX27 i.MX31 i.MX35 i.MX51 especially tested on i.MX31.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add Mode 4 and Mode 5 support to the SH_KEYSC driver. These modes allow
slightly larger key pad matrixes.
While at it, make use of resource_size().
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The ADP5587 is quite similar to the ADP5588 but features a greater I/O
voltage range and lacks the Dual Light Sensor Interface. This new part
is also supported by this driver.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: sentelic - fix left/right horizontal scroll mapping
Input: pmouse - move Sentelic probe down the list
Input: add compat support for sysfs and /proc capabilities output
Input: i8042 - add Dritek quirk for Acer Aspire 5610.
Input: xbox - do not use GFP_KERNEL under spinlock
Input: psmouse - fix Synaptics detection when protocol is disabled
Input: bcm5974 - report ABS_MT events
Input: davinci_keyscan - add device_enable method to platform data
Input: evdev - be less aggressive about sending SIGIO notifies
Input: atkbd - fix canceling event_work in disconnect
Input: serio - fix potential deadlock when unbinding drivers
Input: gf2k - fix &&/|| confusion in gf2k_connect()
Use struct matrix_keymap_data to supply the keymap from the platform code
and matrix_keypad_build_keymap() to initialize the keymap.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The id_table field of the struct i2c_driver is defined as constant
in <linux/i2c.h> so it makes sense to mark the initialization data also
constant.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
dev_err(), dev_warn() and dev_dbg() ensure consistency in driver messages.
Also switch to using bool where appropriate and fix some formatting issues.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add a function pointer in the platform data of the DaVinci Keyscan driver
called device_enable, in order to perform board specific actions when
the device is initialized, like setup the PINMUX configuration.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We need to first unregister input device and only then cancel event work
since events can arrive (and cause event work to get scheduled again)
until input_unregister_device() returns.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
sysfs_remove_group() waits for sysfs attributes to be removed, therefore
we do not need to worry about driver-specific attributes being accessed
after driver has been detached from the device. In fact, attempts to take
serio->drv_mutex in attribute methods may lead to the following deadlock:
sysfs_read_file()
fill_read_buffer()
sysfs_get_active_two()
psmouse_attr_show_helper()
serio_pin_driver()
serio_disconnect_driver()
mutex_lock(&serio->drv_mutex);
<--------> mutex_lock(&serio_drv_mutex);
psmouse_disconnect()
sysfs_remove_group(... psmouse_attr_group);
....
sysfs_deactivate();
wait_for_completion();
Fix this by removing calls to serio_[un]pin_driver() and functions themselves
and using driver-private mutexes to serialize access to attribute's set()
methods that may change device state.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: iforce - wait for command completion when closing the device
Input: twl4030-pwrbutton - switch to using threaded IRQ
Input: twl4030_keypad - switch to using threaded IRQ
Input: lifebook - add CONFIG_DMI dependency
Input: wistron - fix test for CONFIG_PM
Input: psmouse - fix compile warning in hgpk module
Input: matrix-keypad - handle cases when GPIOs can't be wakeup sources
Input: iforce - fix oops on device disconnect
Input: ff-memless - add notion of direction to for rumble effects
Input: ff-memless - another fix for signed to unsigned overflow
Input: ff-memless - start playing FF effects immediately
Input: serio - do not mark kseriod freezable anymore
Input: speed up suspend/shutdown for PS/2 mice and keyboards
On certain boards not all GPIOs may be used as wakeup sources, in which
case some of enable_irq_wake() calls will fail. On resume calling
disable_irq_wake() will warn about unbalanced IRQ wake disable.
Solve this by checking whether enable_irq_wake() succeeded or not and
no not call disable_irq_wake() for these GPIOs/IRQs that have not been
enabled.
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of doing full-blown reset while suspending or shutting down
the box use lighter form of reset that should take less time.
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (22 commits)
Input: ALPS - add interleaved protocol support (Dell E6x00 series)
Input: keyboard - don't override beep with a bell
Input: altera_ps2 - fix test of unsigned in altera_ps2_probe()
Input: add mc13783 touchscreen driver
Input: ep93xx_keypad - update driver to new core support
Input: wacom - separate pen from express keys on Graphire
Input: wacom - add defines for data packet report IDs
Input: wacom - add support for new LCD tablets
Input: wacom - add defines for packet lengths of various devices
Input: wacom - ensure the device is initialized properly upon resume
Input: at32psif - do not sleep in atomic context
Input: i8042 - add Gigabyte M1022M to the noloop list
Input: i8042 - allow installing platform filters for incoming data
Input: i8042 - fix locking in interrupt routine
Input: ALPS - do not set REL_X/REL_Y capabilities on the touchpad
Input: document use of input_event() function
Input: sa1111ps2 - annotate probe() and remove() methods
Input: ambakmi - annotate probe() and remove() methods
Input: gscps2 - fix probe() and remove() annotations
Input: altera_ps2 - add annotations to probe and remove methods
...
This driver was merged before the ep93xx core support was added
for the keypad clock and acquiring/releasing the necessary gpio's.
Now that the proper support is in the ep93xx core this driver
needs to be updated to work correctly.
Summary of changes:
1) Remove some unused members from the platform data.
2) Remove the custom KEY macro and use the ones available in
<linux/input/matrix_keypad.h>
3) Remove the keypad_{readl/writel} macros and just use
__raw_{readl/writel} directly.
4) Update the clk_set_rate() call to work with the core support.
5) Cleanup the probe routine and remove some unneeded messages.
6) Use the ep93xx core functions to acquire and release the gpio's.
7) Fix the clk_get() call to get the keypad clock.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch renames function names like twl4030_i2c_write_u8,
twl4030_i2c_read_u8 to twl_i2c_write_u8, twl_i2c_read_u8
and also common variable in twl-core.c
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.
This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (51 commits)
Input: appletouch - give up maintainership
Input: dm355evm_kbd - switch to using sparse keymap library
Input: wistron_btns - switch to using sparse keymap library
Input: add generic support for sparse keymaps
Input: fix memory leak in force feedback core
Input: wistron - remove identification strings from DMI table
Input: psmouse - remove identification strings from DMI tables
Input: atkbd - remove identification strings from DMI table
Input: i8042 - remove identification strings from DMI tables
DMI: allow omitting ident strings in DMI tables
Input: psmouse - do not carry DMI data around
Input: matrix-keypad - switch to using dev_pm_ops
Input: keyboard - fix lack of locking when traversing handler->h_list
Input: gpio_keys - scan gpio state at probe and resume time
Input: keyboard - add locking around event handling
Input: usbtouchscreen - add support for ET&T TC5UH touchscreen controller
Input: xpad - add two new Xbox 360 devices
Input: polled device - do not start polling if interval is zero
Input: polled device - schedule first poll immediately
Input: add S3C24XX touchscreen driver
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (137 commits)
sh: include empty zero page in romImage
sh: Make associative cache writes fatal on all SH-4A parts.
sh: Drop associative writes for SH-4 cache flushes.
sh: Partial revert of copy/clear_user_highpage() optimizations.
sh: Add default uImage rule for se7724, ap325rxa, and migor.
sh: allow runtime pm without suspend/resume callbacks
sh: mach-ecovec24: Remove un-defined settings for VPU
sh: mach-ecovec24: LCDC drive ability become high
sh: fix sh7724 VEU3F resource size
serial: sh-sci: Fix too early port disabling.
sh: pfc: pr_info() -> pr_debug() cleanups.
sh: pfc: Convert from ctrl_xxx() to __raw_xxx() I/O routines.
sh: Improve kfr2r09 serial port setup code
sh: Break out SuperH PFC code
sh: Move KEYSC header file
sh: convert /proc/cpu/aligmnent, /proc/cpu/kernel_alignment to seq_file
sh: Add CPG save/restore code for sh7724 R-standby
sh: Add SDHI power control support to Ecovec
mfd: Add power control platform data to SDHI driver
sh: mach-ecovec24: modify address map
...
The driver does not reference identification strings in DMI table and
since these strings are no longer required by DMI core we can safely
remove them and save some memory.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We need to read and report gpio state when we bind the driver to the
device and upon resume so that userspace has correct state of the
switches (and keys but they are less important since, even if they
are happened to be pressed, we'd expect them to be released fairly
soon).
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch moves the KEYSC header file from the
SuperH specific asm directory to a place where
it can be shared by multiple architectures.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move the code that deals with setting up each individual button out into
a new function to reduce the indentation and allow us to common up some
of the error recovery code.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The gpio keys driver should be using <linux/gpio.h> instead
of <asm/gpio.h>
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The gpio_keys driver is binding to a platform device but using pr_err()
to report errors. Change to using dev_err() so that all messages are
prefixed by the device name.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Even though input core tells us to restore LED state and repeat rate
at resume keyboard may be reconnected either by request from userspace
(via sysfs) or just by pulling it from the box and plugging it back in.
In these cases we still need to restore state ourselves.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is nothing that disallows gpio-keys to share it's IRQ line
w/ other drivers. Make it use IRQF_SHARED in request_irq().
An example of other driver with which I'd like to share IRQ line
for GPIO buttons is ledtrig-gpio.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
OQO 01+ multimedia keys produce 6x on press, e0 6x upon release.
As a result, Linux thinks that another key has been pressed (or is
repeating), when it is actually a release of the same key. Mangle the
release scancode when running on OQO so that driver recognizes it as
such.
Since the device does not have external PS/2 ports mangling is safe
since there is no chance that an external keyboard is connected.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some machines share same key list for volume up/down release key quirks,
use only one key list.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We need to postpone restoring LED state and typematic settings until
keyboard is finished reconnecting upon resume. Normally driver core
and PM infrastructure takes care of proper ordering and dependencies,
but or case actual reconnect is done asynchronously from kseriod.
So while driver core thinks that keyboard was resumed and it is time
to let input core run it's resume handlers in reality keyboard is not
ready yet. The solution is to keep rescheduling work that adjusts LED
and rate settings until keyboard is fully enabled.
Reported-by: Carlos R. Mafra <crmafra2@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This driver enables keypad support on DaVinci platforms. DM365 is the
only platform that uses this driver at the moment.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
- no spaces between function name and opening parenthesis
- switch statements were indented too much
This makes checkpatch (and me) happy.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix breakage caused by commit 9605fb48e1
While the input core indeed takes care of restoring led state and
typematic settings upon resume the driver still need to initialize
them properly when registering a new device
Reported-and-tested-by: Marin Mitov <mitov@issp.bas.bg>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
This version only supports individual cells (no slide support yet).
The code has been tested on proprietary development ARM board, but
should work fine on other machines.
Signed-off-by: Raphael Derosso Pereira <raphaelpereira@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Convert max7359 driver to use IRQ threading instead of using
workqueue.
Tested-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Maxim MAX7359 is a I2C interfaced key switch controller which
provides microprocessors with management of up to 64 key switches.
This patch adds support for the MAX7359 key switch controller.
Signed-off-by: Kim Kyuwon <q1.kim@samsung.com>
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (262 commits)
sh: mach-ecovec24: Add user debug switch support
sh: Kill off unused se_skipped in alignment trap notification code.
sh: Wire up HAVE_SYSCALL_TRACEPOINTS.
video: sh_mobile_lcdcfb: use both register sets for display panning
video: sh_mobile_lcdcfb: implement display panning
sh: Fix up sh7705 flush_dcache_page() build.
sh: kfr2r09: document the PLL/FLL <-> RF relationship.
sh: mach-ecovec24: need asm/clock.h.
sh: mach-ecovec24: deassert usb irq on boot.
sh: Add KEYSC support for EcoVec24
sh: add kycr2_delay for sh_keysc
sh: cpufreq: Include CPU id in info messages.
sh: multi-evt support for SH-X3 proto CPU.
sh: clkfwk: remove bogus set_bus_parent() from SH7709.
sh: Fix the indication point of the liquid crystal of AP-325RXA(AP3300)
sh: Add EcoVec24 romImage defconfig
sh: USB disable process is needed if romImage boot for EcoVec24
sh: EcoVec24: add HIZA setting for LED
sh: EcoVec24: write MAC address in boot
sh: Add romImage support for EcoVec24
...
Now that input core takes care of restoring state of input devices
upon resume we don't need to do anything special here.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Due to problems at cam.org, my nico@cam.org email address is no longer
valid. FRom now on, nico@fluxnic.net should be used instead.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After KYCR2 is set, udelay might become necessary if there are only a
small number of keys attached. This patch introduces an optional delay
through the platform data to address this problem.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Compaq Presario R4000-series laptops are not sending a "volume up button
release" and "volume down button release" signal in the PS/2 protocol for
atkbd. The URL below has some of confirmed reports:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/385477
Signed-off-by: Dave Andrews <jetdog330@hotmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There are more and more laptop requiring use of force_release quirk
for their multimedia and other specialized keys. Adding their DMI data
to the kernel is not sustainable; instead we will rely on help from
userspace (HAL) to do that for us.
This patch creates a new 'force_release' sysfs attribute (that belongs
to serio device to which keyboard is attached) which can be used to set
up force_release keymap. For example, Dell laptop owners might do:
echo 133-139,143,147 > /sys/devices/platform/i8042/serio0/force_release
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We should first check whether platform data is NULL or not, before
dereferencing it to get the keymap.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add a driver for the keypad controller on TWL4030 family chips.
These support up to an 8x8 key matrix. The TWL4030 multifunction
chips are mostly used on OMAP3 (or OMAP 2430) based boards.
[dtor@mail.ru: switch to matrix-keypad framework, fix changing
keymap from userspace]
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Direct to fail2 to gpio_free() the KEY_STROBEs as well as the KEY_SENSEs.
[dtor@mail.ru: change keymap from unsigned int to unsigned short]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Also have the driver send MSC_SCAN events as most keyboards do to aid
in updating keymap from userspace.
Tested-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add keypad driver for the 4x4 keypad on an evaluation board based
on w90p910.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
hil_kbd and hil_ptr look like twins so it makes sense to combine them
into a single driver.
[deller@gmx.de: add MODULE_ALIAS() entry for mouse]
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Rename functions and variables from [hil_]kbd to [hil_]dev in
preparation of merging hil_kbd and hil_ptr.
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Remove assumption on the shift and size of rows/columns form
matrix_keypad driver.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
clk_disable() in remove method is not needed since we already
have clk_disable in pxa27x_keypad_close().
Also make sure the driver uses resource_size() and helpers from
include/input/matrix_keypad.h
Tested-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Netbooks based on the Soltech TA12 do not send a key release
for volume keys causing Linux to think the key is constantly
being pressed forever.
Added quirk data for forced release keys.
BugLink: https://bugs.launchpad.net//bugs/397499
Signed-off-by: Jerone Young <jerone.young@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch enables forced releasing of the Fn+Volume hotkeys
on the Fujitsu Siemens Amilo Pi 3525 notebook.
Signed-off-by: Simon Davie <nexx@nexxdesign.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Original patch by Marek Vasut, modified by Eric in:
1. use delayed work to simplify the debouncing
2. combine col_polarity/row_polarity into a single active_low field
3. use a generic bit array based XOR algorithm to detect key
press/release, which should make the column assertion time
shorter and code a bit cleaner
4. remove the ALT_FN handling, which is no way generic, the ALT_FN
key should be treated as no different from other keys, and
translation will be done by user space by commands like 'loadkeys'.
5. explicitly disable row IRQs and flush potential pending work,
and schedule an immediate scan after resuming as suggested
by Uli Luckas
6. incorporate review comments from many others
Patch tested on Littleton/PXA310 (though PXA310 has a dedicate keypad
controller, I have to configure those pins as generic GPIO to use this
driver, works quite well, though), and Sharp Zaurus model SL-C7x0
and SL-C1000.
[dtor@mail.ru: fix error unwinding path, support changing keymap
from userspace]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Reviewed-by: Uli Luckas <u.luckas@road.de>
Reviewed-by: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The gpio_get_value function may sleep, so it should not be called in a
timer function. Move gpio_get_value calls to workqueue.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This reverts commit 0b346838c5.
This commit breaks GPIO debouncing by replacing the original mod_timer
with schedule_delayed_work in the interrupt handler. The latter does not
kick the timer further on GPIO line changes as it should to perform
debouncing.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The gpio_get_value function of I2C/SPI GPIO expander may sleep thus this
function call can not be called in a timer function.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
lm8323 is the keypad driver used in n810 device.
[akpm@linux-foundation.org: coding-style fixes]
[dtor@mail.ru: various cleanups]
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is a keyboard driver for the Cirrus Logic EP93xx keypad matrix
peripheral. This driver is based on the pxa27x_keypad driver.
[dtor@mail.ru: Plug in input_dev->keycode so keymap can be changed
from userspace.]
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
disable_irq() waits for all running handlers to complete before
returning. As such, if it's used to disable an interrupt from
that interrupt's handler it will deadlock. This replaces the
dangerous instances with the _nosync() variant which doesn't have
this problem.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Modify the sh_keysc driver to use enable/disable_irq_wake()
during suspend and resume. These functions are used to enable
the sh_keysc interrupt in the interrupt controller so the
keypad can be used to wakeup the system from suspend.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (422 commits)
[ARM] 5435/1: fix compile warning in sanity_check_meminfo()
[ARM] 5434/1: ARM: OMAP: Fix mailbox compile for 24xx
[ARM] pxa: fix the bad assumption that PCMCIA sockets always start with 0
[ARM] pxa: fix Colibri PXA300 and PXA320 LCD backlight pins
imxfb: Fix TFT mode
i.MX21/27: remove ifdef CONFIG_FB_IMX
imxfb: add clock support
mxc: add arch_reset() function
clkdev: add possibility to get a clock based on the device name
i.MX1: remove fb support from mach-imx
[ARM] pxa: build arch/arm/plat-pxa/mfp.c only when PXA3xx or ARCH_MMP defined
Gemini: Add support for Teltonika RUT100
Gemini: gpiolib based GPIO support v2
MAINTAINERS: add myself as Gemini architecture maintainer
ARM: Add Gemini architecture v3
[ARM] OMAP: Fix compile for omap2_init_common_hw()
MAINTAINERS: Add myself as Faraday ARM core variant maintainer
ARM: Add support for FA526 v2
[ARM] acorn,ebsa110,footbridge,integrator,sa1100: Convert asm/io.h to linux/io.h
[ARM] collie: fix two minor formatting nits
...
This patch changes sh_keysc to use to_platform_device()
for suspend. Thanks to Trilok Soni for this suggestion.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds wakeup support to the sh_keysc driver.
With this feature the ".../power/wakeup" file can be
used to enable and disable if the device takes the
system out of suspend. Default is enabled.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
pxa-regs.h and hardware.h are not intended for use directly in driver
code, remove those unnecessary references.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
On parisc machines, which don't have HIL, removing the hilkbd module
panics the kernel. Fix this by adding proper implementations for the
probe and remove functions to the parisc_driver structure.
A few functions were renamed to clean up the code and make it easier
readable.
Disable the MODULE_DEVICE_TABLE() macro on parisc since the kernel
module autoloader should instead prefer the hp_sdc driver which takes
care of full HIL support, including HIL mouse and HIL tablets.
[dtor@mail.ru: fix some section markups]
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The volume up and down keys on the Fujitsu Siemens Amilo PA 1510 laptop
won't generate release events, so we have to do that. Use the same
way that is already used with other models.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - touchpad driver miss-recognising logitech mice
Input: synaptics - ensure we reset the device on resume
Input: usbtouchscreen - fix eGalax HID ignoring
Input: ambakmi - fix timeout handling in amba_kmi_write()
Input: pxa930_trkball - fix write timeout handling
Input: struct device - replace bus_id with dev_name(), dev_set_name()
Input: bf54x-keys - fix debounce time validation
Input: spitzkbd - mark probe function as __devinit
Input: omap-keypad - mark probe function as __devinit
Input: corgi_ts - mark probe function as __devinit
Input: corgikbd - mark probe function as __devinit
Input: uvc - the button on the camera is KEY_CAMERA
Input: psmouse - make MOUSE_PS2_LIFEBOOK depend on X86
Input: atkbd - make forced_release_keys[] static
Input: usbtouchscreen - allow reporting calibrated data
This patch updates the maple bus to support asynchronous block reads
and writes as well as generally improving the quality of the code and
supporting concurrency (all needed to support the Dreamcast visual
memory unit - a driver will also be posted for that).
Changes in the bus driver necessitate some changes in the two maple bus
input drivers that are currently in mainline.
As well as supporting block reads and writes this code clean up removes
some poor handling of locks, uses an atomic status variable to serialise
access to devices and more robusly handles the general performance
problems of the bus.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
X86_PC is the only remaining 'sub' architecture, so we dont need
it anymore.
This also cleans up a few spurious references to X86_PC in the
driver space - those certainly should be X86.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
A pointer to spitzkbd_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
[dtor@mail.ru: fixed some more section markups]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A pointer to omap_kp_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
[dtor@mail.ru: fixed some more section markups]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A pointer to corgikbd_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
[dtor@mail.ru: fixed some more section markups]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (29 commits)
Input: i8042 - add Dell Vostro 1510 to nomux list
Input: gtco - use USB endpoint API
Input: add support for Maple controller as a joystick
Input: atkbd - broaden the Dell DMI signatures
Input: HIL drivers - add MODULE_ALIAS()
Input: map_to_7segment.h - convert to __inline__ for userspace
Input: add support for enhanced rotary controller on pxa930 and pxa935
Input: add support for trackball on pxa930 and pxa935
Input: add da9034 touchscreen support
Input: ads7846 - strict_strtoul takes unsigned long
Input: make some variables and functions static
Input: add tsc2007 based touchscreen driver
Input: psmouse - add module parameters to control OLPC touchpad delays
Input: i8042 - add Gigabyte M912 netbook to noloop exception table
Input: atkbd - Samsung NC10 key repeat fix
Input: atkbd - add keyboard quirk for HP Pavilion ZV6100 laptop
Input: libps2 - handle 0xfc responses from devices
Input: add support for Wacom W8001 penabled serial touchscreen
Input: synaptics - report multi-taps only if supported by the device
Input: add joystick driver for Walkera WK-0701 RC transmitter
...
It is always "an" if there is a vowel _spoken_ (not written).
So it is:
"an hour" (spoken vowel)
but
"a uniform" (spoken 'j')
Signed-off-by: Frederik Schwarzer <schwarzerf@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (407 commits)
[ARM] pxafb: add support for overlay1 and overlay2 as framebuffer devices
[ARM] pxafb: cleanup of the timing checking code
[ARM] pxafb: cleanup of the color format manipulation code
[ARM] pxafb: add palette format support for LCCR4_PAL_FOR_3
[ARM] pxafb: add support for FBIOPAN_DISPLAY by dma braching
[ARM] pxafb: allow pxafb_set_par() to start from arbitrary yoffset
[ARM] pxafb: allow video memory size to be configurable
[ARM] pxa: add document on the MFP design and how to use it
[ARM] sa1100_wdt: don't assume CLOCK_TICK_RATE to be a constant
[ARM] rtc-sa1100: don't assume CLOCK_TICK_RATE to be a constant
[ARM] pxa/tavorevb: update board support (smartpanel LCD + keypad)
[ARM] pxa: Update eseries defconfig
[ARM] 5352/1: add w90p910-plat config file
[ARM] s3c: S3C options should depend on PLAT_S3C
[ARM] mv78xx0: implement GPIO and GPIO interrupt support
[ARM] Kirkwood: implement GPIO and GPIO interrupt support
[ARM] Orion: share GPIO IRQ handling code
[ARM] Orion: share GPIO handling code
[ARM] s3c: define __io using the typesafe version
[ARM] S3C64XX: Ensure CPU_V6 is selected
...
Some Dells need the dell input quirk applied but have a different vendor
string in their DMI tables. Add an extra entry to cover these machines as
well.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add MODULE_ALIAS() to the HIL keyboard (hil_kbd.c) and HIL mouse
(hil_ptr.c) drivers to make kernel module autoloader functional.
Report HIL port number ID in serio id.id field.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add clock framework support to the sh_mobile keysc driver and
adjust the board specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the key repeat issue with the Fn+F? keys on the new
Samsung NC10 Netbook, so that the keys can be defined and used within
ACPID correctly, otherwise the keys repeat indefinately.
This solves part of http://bugzilla.kernel.org/show_bug.cgi?id=12021
Signed-off-by: Stuart Hopkins <stuart@dodgy-geeza.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add quirk for misbehaving volume buttons on HP Pavilion ZV6100 laptop which
are not sending keyrelease events, as reported by Aaron Pickett.
Signed-off-by: Rikard Ljungstrand <lrikard@student.chalmers.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Have most uses of OMAP_GPIO_IRQ() use gpio_to_irq() instead.
Calls used for table initialization are left alone, at least
this time around.
(This patch is for code in both the OMAP tree and mainline.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - add support for new USB Tablet PCs
Input: replace spin_lock_bh with spin_lock_irqsave in ml_ff_playback
Input: i8042 - add Compal Hel80 laptop to nomux blacklist
Input: cm109 - add keymap for ATCom AU-100 phone
Input: fix the example of an input device driver
Input: psmouse - fix incorrect validate_byte check in OLPC protocol
Input: atkbd - cancel delayed work before freeing its structure
Input: atkbd - add keymap quirk for Inventec Symphony systems
Input: i8042 - add Dell XPS M1530 to nomux list
Input: elo - fix format string in elo driver
Where devices only have one consumer, passing a consumer clock ID
has no real benefit. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pointed out by Oleg Nesterov. Since delayed work is used here, use of
flush_scheduled_work() is not sufficient in atkbd_disconnect(). It does
not wait for scheduled delayed work to finish. This patch prevents
delayed work to be processed after freeing atkbd structure (used struct
delayed_work is part of atkbd) by cancelling this delayed work.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Zepto 6615WD laptop (rebranded Inventec Symphony system) needs a
key release quirk for its volume keys to work. The attached patch adds
the quirk to the atkbd driver.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=460237
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is no reason to limit the GPIO rows to 6 for OMAP2.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The GPIO interrupts are disabled several times after the first key press.
No need to disable - again - the interrupts in the omap_kp_scan_keypad
function on OMAP2.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Linus Torvalds