The current Cadence QSPI driver sometimes caused a
"rcu_sched self-detected stall" while writing large files.
Stall Report:
'# mtd_debug write /dev/mtd1 0 48816464 blob.img
[ 1815.454227] rcu: INFO: rcu_sched self-detected stall on CPU
[ 1815.459789] rcu: 0-....: (2099 ticks this GP) idle=8c6/1/0x40000002
softirq=6492/6492 fqs=935
[ 1815.468442] rcu: (t=2100 jiffies g=8749 q=247)
<snip> (abbreviated backtrace)
[ 1815.772086] [<c05a3ea0>] (cqspi_exec_flash_cmd) (cqspi_read_reg)
[ 1815.786203] [<c05a5488>] (cqspi_read_reg) from (read_sr)
[ 1815.803790] [<c05a0330>] (read_sr) from
(spi_nor_wait_till_ready_with_timeout)
[ 1815.816610] [<c05a182c>] (spi_nor_wait_till_ready_with_timeout) from
(spi_nor_write+0x104/0x1d0)
[ 1815.836791] [<c05a1a44>] (spi_nor_write) from (part_write+0x50/0x58)
<snip>
[ 1815.997961] cadence-qspi ff809000.spi: Flash command execution timed out.
[ 1816.004733] error -110 reading SR
file_to_flash: write, size 0x2e8e150, n 0x2e8e150
write(): Connection timed out
This was caused by a tight loop in cqspi_wait_for_bit(). Fix by using
readl_relaxed_poll_timeout() which sleeps 10us while polling a register.
Fit onto 80 character line by truncating the bool clear parameter
Fixes: 1406234105 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller")
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAl0V1XYACgkQS1VPR6WN
FOkBbQf+Iv2+vmoDGDCVGO4LZh+N/l0Sh/C31hJj5y7GVkCdwMJCvdOrGEhDkseu
Dc0gchT6uy52pAp4N0B88avC8fSJY0UwFRbnqUUA546R9Uf6h+gbGIZCX/rzZuIi
IDDNHc06qbpxpesfC5CowhY49QVGG+O0scgUOE2gKHOfd04kXu6gqIV0BvQZg80R
EpSgifHLUk/b2015FyqB5YFuc2K3HMmcWc6uJx4kSHPCXiCOx8aaEqjKvK9vL0h5
XOxXim5HhuzFqQ8vSPqvnKDokkuV3pcSUcaQyjQjrebTlectaDjGZlLF17Udm9Q9
I0zI+7deXK9L4roatEryzOdW0Ql3Hw==
=J5Uw
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.3-v2' of gitolite.kernel.org:pub/scm/linux/kernel/git/mtd/linux into mtd/next
SPI-NOR core changes:
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control
Get the reset control properties for the QSPI controller and bring them
out of reset. Most will have just one reset bit, but there is an additional
OCP reset bit that is used ECC. The OCP reset bit will also need to get
de-asserted as well. [1]
The reason this patch is needed is in the case where a bootloader leaves
the QSPI controller in a reset state, or a state where init cannot occur
successfully, the patch will put the QSPI controller into a clean state.
[1] https://www.intel.com/content/www/us/en/programmable/hps/arria-10/hps.html#reg_soc_top/sfo1429890575955.html
Suggested-by: Tien-Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
[tudor.ambarus@microchip.com: declare rstc and rstc_ocp on the same line]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a spelling mistake in a dev_error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Cadence OSPI controller IP supports Octal IO (x8 IO lines),
It also has an integrated PHY. IP register layout is very
similar to existing QSPI IP except for additional bits to support Octal
and Octal DDR mode. Therefore, extend current driver to support Octal
mode. Only Octal SDR read (1-1-8)mode is supported for now.
Tested with mt35xu512aba Octal flash on TI's AM654 EVM.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
cadence-quadspi controller allows upto eight bytes of data to
be written in software Triggered Instruction generator (STIG) mode
of operation. Lower 4 bytes are written through writedatalower and
upper 4 bytes by writedataupper register.
This patch allows all the 8 bytes to be written.
Signed-off-by: Purna Chandra Mandal <purna.chandra.mandal@intel.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
The current Cadence QSPI driver caused a kernel panic sporadically
when writing to QSPI. The problem was caused by writing more bytes
than needed because the QSPI operated on 4 bytes at a time.
<snip>
[ 11.202044] Unable to handle kernel paging request at virtual address bffd3000
[ 11.209254] pgd = e463054d
[ 11.211948] [bffd3000] *pgd=2fffb811, *pte=00000000, *ppte=00000000
[ 11.218202] Internal error: Oops: 7 [#1] SMP ARM
[ 11.222797] Modules linked in:
[ 11.225844] CPU: 1 PID: 1317 Comm: systemd-hwdb Not tainted 4.17.7-d0c45cd44a8f
[ 11.235796] Hardware name: Altera SOCFPGA Arria10
[ 11.240487] PC is at __raw_writesl+0x70/0xd4
[ 11.244741] LR is at cqspi_write+0x1a0/0x2cc
</snip>
On a page boundary limit the number of bytes copied from the tx buffer
to remain within the page.
This patch uses a temporary buffer to hold the 4 bytes to write and then
copies only the bytes required from the tx buffer.
Reported-by: Adrian Amborzewicz <adrian.ambrozewicz@intel.com>
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
We return 0 unconditionally in 'cqspi_direct_read_execute()'.
However, 'ret' is set to some error codes in several error handling
paths.
Return 'ret' instead to propagate the error code.
Fixes: ffa639e069 ("mtd: spi-nor: cadence-quadspi: Add DMA support for direct mode reads")
Cc: <stable@vger.kernel.org>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Clang warns when one enumerated type is converted implicitly to another.
drivers/mtd/spi-nor/cadence-quadspi.c:962:47: warning: implicit
conversion from enumeration type 'enum dma_transfer_direction' to
different enumeration type 'enum dma_data_direction' [-Wenum-conversion]
dma_dst = dma_map_single(nor->dev, buf, len, DMA_DEV_TO_MEM);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~
./include/linux/dma-mapping.h:428:66: note: expanded from macro
'dma_map_single'
~~~~~~~~~~~~~~~~~~~~ ^
drivers/mtd/spi-nor/cadence-quadspi.c:997:43: warning: implicit
conversion from enumeration type 'enum dma_transfer_direction' to
different enumeration type 'enum dma_data_direction' [-Wenum-conversion]
dma_unmap_single(nor->dev, dma_dst, len, DMA_DEV_TO_MEM);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~
./include/linux/dma-mapping.h:429:70: note: expanded from macro
'dma_unmap_single'
~~~~~~~~~~~~~~~~~~~~~~ ^
2 warnings generated.
Use the proper enums from dma_data_direction to satisfy Clang.
DMA_FROM_DEVICE = DMA_DEV_TO_MEM = 2
Link: https://github.com/ClangBuiltLinux/linux/issues/108
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
- Support 64-bit timestamps
MTD changes:
Core changes:
- Support sub-partitions
- Clarify mtd_oob_ops documentation
- Make Kconfig formatting consistent
- Fix potential overflows in mtdchar_{write,read}()
- Fallback to ->_{read,write}() when ->_{read,write}_oob() is missing
and no OOB data were requested
- Remove VLA usage in the bch lib
Driver changes:
- Use mtd_device_register() instead of mtd_device_parse_register()
where applicable
- Use proper printk format to print physical addresses in the
solutionengine driver
- Add missing mtd_set_of_node() call in the powernv driver
- Remove unneeded variables in a few drivers
- Plug the TRX part parser to the DT partition parsers logic
- Check ioremap_cache() return code in the gpio-addr-flash driver
- Stop using VMLINUX_SYMBOL_STR() in gen_probe.c
SPI NOR changes:
Core changes:
- Apply reset hacks only when reset is explicitly marked as broken in
the DT
Driver changes:
- Minor cleanup/fixes in the m25p80 driver
- Release flash_np in the nxp-spifi driver
- Add suspend/resume hooks to the atmel-quadspi driver
- Include gpio/consumer.h instead of gpio.h in the atmel-quadspi
driver
- Use %pK instead of %p in the stm32-quadspi driver
- Improve timeout handling in the cadence-quadspi driver
- Use mtd_device_register() instead of mtd_device_parse_register()
in the intel-spi driver
NAND changes:
Core changes:
- Add the SPI-NAND framework.
- Create a helper to find the best ECC configuration.
- Create NAND controller operations.
- Allocate dynamically ONFI parameters structure.
- Add defines for ONFI version bits.
- Add manufacturer fixup for ONFI parameter page.
- Add an option to specify NAND chip as a boot device.
- Add Reed-Solomon error correction algorithm.
- Better name for the controller structure.
- Remove unused caller_is_module() definition.
- Make subop helpers return unsigned values.
- Expose _notsupp() helpers for raw page accessors.
- Add default values for dynamic timings.
- Kill the chip->scan_bbt() hook.
- Rename nand_default_bbt() into nand_create_bbt().
- Start to clean the nand_chip structure.
- Remove stale prototype from rawnand.h.
Raw NAND controllers drivers changes:
- Qcom: structuring cleanup.
- Denali: use core helper to find the best ECC configuration.
- Possible build of almost all drivers by adding a dependency on
COMPILE_TEST for almost all of them in Kconfig, implies various
fixes, Kconfig cleanup, GPIO headers inclusion cleanup, and even
changes in sparc64 and ia64 architectures.
- Clean the ->probe() functions error path of a lot of drivers.
- Migrate all drivers to use nand_scan() instead of
nand_scan_ident()/nand_scan_tail() pair.
- Use mtd_device_register() where applicable to simplify the code.
- Marvell:
* Handle on-die ECC.
* Better clocks handling.
* Remove bogus comment.
* Add suspend and resume support.
- Tegra: add NAND controller driver.
- Atmel:
* Add module param to avoid using dma.
* Drop Wenyou Yang from MAINTAINERS.
- Denali: optimize timings handling.
- FSMC: Stop using chip->read_buf().
- FSL:
* Switch to SPDX license tag identifiers.
* Fix qualifiers in MXC init functions.
Raw NAND chip drivers changes:
- Micron:
* Add fixup for ONFI revision.
* Update ecc_stats.corrected.
* Make ECC activation stateful.
* Avoid enabling/disabling ECC when it can't be disabled.
* Get the actual number of bitflips.
* Allow forced on-die ECC.
* Support 8/512 on-die ECC.
* Fix on-die ECC detection logic.
- Hynix:
* Fix decoding the OOB size on H27UCG8T2BTR.
* Use ->exec_op() in hynix_nand_reg_write_op().
-----BEGIN PGP SIGNATURE-----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=yIkF
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.19' of git://git.infradead.org/linux-mtd
Pull mtd updates from Boris Brezillon:
"JFFS2 changes:
- Support 64-bit timestamps
MTD core changes:
- Support sub-partitions
- Clarify mtd_oob_ops documentation
- Make Kconfig formatting consistent
- Fix potential overflows in mtdchar_{write,read}()
- Fallback to ->_{read,write}() when ->_{read,write}_oob() is missing
and no OOB data were requested
- Remove VLA usage in the bch lib
MTD driver changes:
- Use mtd_device_register() instead of mtd_device_parse_register()
where applicable
- Use proper printk format to print physical addresses in the
solutionengine driver
- Add missing mtd_set_of_node() call in the powernv driver
- Remove unneeded variables in a few drivers
- Plug the TRX part parser to the DT partition parsers logic
- Check ioremap_cache() return code in the gpio-addr-flash driver
- Stop using VMLINUX_SYMBOL_STR() in gen_probe.c
SPI NOR core changes:
- Apply reset hacks only when reset is explicitly marked as broken in
the DT
SPI NOR driver changes:
- Minor cleanup/fixes in the m25p80 driver
- Release flash_np in the nxp-spifi driver
- Add suspend/resume hooks to the atmel-quadspi driver
- Include gpio/consumer.h instead of gpio.h in the atmel-quadspi
driver
- Use %pK instead of %p in the stm32-quadspi driver
- Improve timeout handling in the cadence-quadspi driver
- Use mtd_device_register() instead of mtd_device_parse_register() in
the intel-spi driver
NAND core changes:
- Add the SPI-NAND framework.
- Create a helper to find the best ECC configuration.
- Create NAND controller operations.
- Allocate dynamically ONFI parameters structure.
- Add defines for ONFI version bits.
- Add manufacturer fixup for ONFI parameter page.
- Add an option to specify NAND chip as a boot device.
- Add Reed-Solomon error correction algorithm.
- Better name for the controller structure.
- Remove unused caller_is_module() definition.
- Make subop helpers return unsigned values.
- Expose _notsupp() helpers for raw page accessors.
- Add default values for dynamic timings.
- Kill the chip->scan_bbt() hook.
- Rename nand_default_bbt() into nand_create_bbt().
- Start to clean the nand_chip structure.
- Remove stale prototype from rawnand.h.
Raw NAND controllers drivers changes:
- Qcom: structuring cleanup.
- Denali: use core helper to find the best ECC configuration.
- Possible build of almost all drivers by adding a dependency on
COMPILE_TEST for almost all of them in Kconfig, implies various
fixes, Kconfig cleanup, GPIO headers inclusion cleanup, and even
changes in sparc64 and ia64 architectures.
- Clean the ->probe() functions error path of a lot of drivers.
- Migrate all drivers to use nand_scan() instead of
nand_scan_ident()/nand_scan_tail() pair.
- Use mtd_device_register() where applicable to simplify the code.
- Marvell:
* Handle on-die ECC.
* Better clocks handling.
* Remove bogus comment.
* Add suspend and resume support.
- Tegra: add NAND controller driver.
- Atmel:
* Add module param to avoid using dma.
* Drop Wenyou Yang from MAINTAINERS.
- Denali: optimize timings handling.
- FSMC: Stop using chip->read_buf().
- FSL:
* Switch to SPDX license tag identifiers.
* Fix qualifiers in MXC init functions.
Raw NAND chip drivers changes:
- Micron:
* Add fixup for ONFI revision.
* Update ecc_stats.corrected.
* Make ECC activation stateful.
* Avoid enabling/disabling ECC when it can't be disabled.
* Get the actual number of bitflips.
* Allow forced on-die ECC.
* Support 8/512 on-die ECC.
* Fix on-die ECC detection logic.
- Hynix:
* Fix decoding the OOB size on H27UCG8T2BTR.
* Use ->exec_op() in hynix_nand_reg_write_op()"
* tag 'mtd/for-4.19' of git://git.infradead.org/linux-mtd: (188 commits)
mtd: rawnand: atmel: Select GENERIC_ALLOCATOR
MAINTAINERS: drop Wenyou Yang from Atmel NAND driver support
mtd: rawnand: allocate dynamically ONFI parameters during detection
mtd: spi-nor: only apply reset hacks to broken hardware
mtd: spi-nor: cadence-quadspi: fix timeout handling
mtd: spi-nor: atmel-quadspi: Include gpio/consumer.h instead of gpio.h
mtd: spi-nor: intel-spi: use mtd_device_register()
mtd: spi-nor: stm32-quadspi: replace "%p" with "%pK"
mtd: spi-nor: atmel-quadspi: add suspend/resume hooks
mtd: rawnand: allocate model parameter dynamically
mtd: rawnand: do not export nand_scan_[ident|tail]() anymore
mtd: rawnand: txx9ndfmc: convert driver to nand_scan()
mtd: rawnand: txx9ndfmc: clarify ECC parameters assignation
mtd: rawnand: tegra: convert driver to nand_scan()
mtd: rawnand: jz4740: convert driver to nand_scan()
mtd: rawnand: jz4740: group nand_scan_{ident, tail} calls
mtd: rawnand: jz4740: fix probe function error path
mtd: rawnand: docg4: convert driver to nand_scan()
mtd: rawnand: do not execute nand_scan_ident() if maxchips is zero
mtd: rawnand: atmel: convert driver to nand_scan()
...
wait_for_completion_timeout returns an unsigned long not an int, so
let's check its return value directly instead of storing it in ret,
and avoid checking for negative values since this cannot happen.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Sometimes when writing large size files to flash in direct/memory mapped
mode, it is seen that flash write enable command times out with error:
[ 503.146293] cadence-qspi 47040000.ospi: Flash command execution timed out.
This is because, we need to make sure previous direct write operation
is complete by polling for IDLE bit in CONFIG_REG before starting the
next operation.
Fix this by polling for IDLE bit after memory mapped write.
Fixes: a27f2eaf2b ("mtd: spi-nor: cadence-quadspi: Add support for direct access mode")
Cc: stable@vger.kernel.org
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Core changes:
- Add a sysfs attribute to expose available OOB size
Driver changes:
- Remove HAS_DMA dependency on various drivers
- Use dev_get_drvdata() instead of platform_get_drvdata() in docg3
- Replace msleep by usleep_range() in the dataflash driver
- Avoid VLA usage in nftl layers
- Remove useless .owner assignment in pismo
- Fix various issues in the CFI driver
- Improve TRX partition handling expose a DT compat for this part
parser
- Clarify OFFSET_CONTINUOUS meaning
NAND changes:
Core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
* Cleanup/simplification of a few aspects in the driver
* Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
* Use of_device_get_match_data() instead of of_match_device()
* Add an entry in MAINTAINERS for this driver
* Fix nand-ecc-step-size and nand-ecc-strength description in the DT
bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
SPI NOR changes:
Core changes:
- Add support for a bunch of SPI NOR chips
- Clear EAR reg when switching to 3-byte addressing mode on Winbond
chips
SPI NOR controller driver changes:
- cadence: Add DMA support for direct mode reads
- hisi: Prefix a few functions with hisi_
- intel:
* Mark the driver as "dangerous" in Kconfig
* Fix atomic sequence handling
* Pass a 40us delay (instead of 0us) to readl_poll_timeout()
- fsl:
* fix a typo in a function name
* add support for IP variants embedded in the ls2080a and ls1080a
SoCs
- stm32: request exclusive control of the reset line
-----BEGIN PGP SIGNATURE-----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=cHjU
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"Core changes:
- Add a sysfs attribute to expose available OOB size
Driver changes:
- Remove HAS_DMA dependency on various drivers
- Use dev_get_drvdata() instead of platform_get_drvdata() in docg3
- Replace msleep by usleep_range() in the dataflash driver
- Avoid VLA usage in nftl layers
- Remove useless .owner assignment in pismo
- Fix various issues in the CFI driver
- Improve TRX partition handling expose a DT compat for this part
parser
- Clarify OFFSET_CONTINUOUS meaning
NAND core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
+ Cleanup/simplification of a few aspects in the driver
+ Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
+ Use of_device_get_match_data() instead of of_match_device()
+ Add an entry in MAINTAINERS for this driver
+ Fix nand-ecc-step-size and nand-ecc-strength description in the
DT bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
SPI NOR core changes:
- Add support for a bunch of SPI NOR chips
- Clear EAR reg when switching to 3-byte addressing mode on Winbond
chips
SPI NOR controller driver changes:
- cadence: Add DMA support for direct mode reads
- hisi: Prefix a few functions with hisi_
- intel:
+ Mark the driver as "dangerous" in Kconfig
+ Fix atomic sequence handling
+ Pass a 40us delay (instead of 0us) to readl_poll_timeout()
- fsl:
+ fix a typo in a function name
+ add support for IP variants embedded in the ls2080a and ls1080a
SoCs
- stm32: request exclusive control of the reset line"
* tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd: (66 commits)
mtd: nand: Pass mode information to nand_page_io_req
mtd: cfi_cmdset_0002: Change erase one block to enable XIP once
mtd: cfi_cmdset_0002: Change erase functions to check chip good only
mtd: cfi_cmdset_0002: Change erase functions to retry for error
mtd: cfi_cmdset_0002: Change definition naming to retry write operation
mtd: cfi_cmdset_0002: Change write buffer to check correct value
mtd: cmdlinepart: Update comment for introduction of OFFSET_CONTINUOUS
mtd: bcm47xxpart: add of_match_table with a new DT binding
dt-bindings: mtd: document Broadcom's BCM47xx partitions
mtd: spi-nor: Add support for EN25QH32
mtd: spi-nor: Add support for is25wp series chips
mtd: spi-nor: Add Winbond w25q32jv support
mtd: spi-nor: fsl-quadspi: add support for ls2080a/ls1080a
mtd: spi-nor: stm32-quadspi: explicitly request exclusive reset control
mtd: spi-nor: intel: provide a range for poll_timout
mtd: spi-nor: fsl-quadspi: fix api naming typo _init_ahb_read
mtd: spi-nor: intel-spi: Explicitly mark the driver as dangerous in Kconfig
mtd: spi-nor: intel-spi: Fix atomic sequence handling
mtd: rawnand: Do not check FAIL bit when executing a SET_FEATURES op
mtd: rawnand: use bit-wise majority to recover the ONFI param page
...
The current Cadence QSPI driver caused a kernel panic when loading
a Root Filesystem from QSPI. The problem was caused by reading more
bytes than needed because the QSPI operated on 4 bytes at a time.
<snip>
[ 7.947754] spi_nor_read[1048]:from 0x037cad74, len 1 [bfe07fff]
[ 7.956247] cqspi_read[910]:offset 0x58502516, buffer=bfe07fff
[ 7.956247]
[ 7.966046] Unable to handle kernel paging request at virtual
address bfe08002
[ 7.973239] pgd = eebfc000
[ 7.975931] [bfe08002] *pgd=2fffb811, *pte=00000000, *ppte=00000000
</snip>
Notice above how only 1 byte needed to be read but by reading 4 bytes
into the end of a mapped page, an unrecoverable page fault occurred.
This patch uses a temporary buffer to hold the 4 bytes read and then
copies only the bytes required into the buffer. A min() function is
used to limit the length to prevent buffer overflows.
Request testing of this patch on other platforms. This was tested
on the Intel Arria10 SoCFPGA DevKit.
Fixes: 0cf1725676 ("mtd: spi-nor: cqspi: Fix build on arches missing readsl/writesl")
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Add support to use DMA over memory mapped reads in direct mode. This
helps in reducing CPU usage from ~100% to ~10% when reading data from
flash. For non-DMA'able/vmalloc'd buffers, driver just falls back to CPU
based memcpy.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Cadence QSPI controller provides direct access mode through which flash
can be accessed in a memory-mapped IO mode. This enables read/write to
flash using memcpy*() functions. This mode provides higher throughput
for both read/write operations when compared to current indirect mode of
operation.
This patch therefore adds support to use QSPI in direct mode. If the
window reserved in SoC's memory map for MMIO access is less that of
flash size(like on most SoCFPGA variants), then the driver falls back
to indirect mode of operation.
On TI's 66AK2G SoC, with ARM running at 600MHz and QSPI at 96MHz
switching to direct mode improves read throughput from 3MB/s to 8MB/s.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Move configuring of indirect read/write start address to
cqspi_indirect_*_execute() function and rename cqspi_indirect_*_setup()
function. This will help to reuse cqspi_indirect_*_setup() function for
supporting direct access mode.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Add pm_runtime* calls to cadence-quadspi driver. This is required to
switch on QSPI power domain on TI 66AK2G SoC during probe.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Fix the reversed goto labels, so that we disable cqspi controller only
if its enabled previously. This is a minor cleanup.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cadence QSPI IP has a adapted loop-back circuit which can be enabled by
setting BYPASS field to 0 in READCAPTURE register. It enables use of
QSPI return clock to latch the data rather than the internal QSPI
reference clock. For high speed operations, adapted loop-back circuit
using QSPI return clock helps to increase data valid window.
Based on DT parameter cdns,rclk-en enable adapted loop-back circuit
for boards which do have QSPI return clock provided.
This patch also modifies cqspi_readdata_capture() function's bypass
parameter to bool to match how its used in the function.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
As per 66AK2G02 TRM[1] SPRUHY8F section 11.15.5.3 Indirect Access
Controller programming sequence, a delay equal to couple of QSPI master
clock(~5ns) is required after setting CQSPI_REG_INDIRECTWR_START bit and
writing data to the flash. Introduce a quirk flag CQSPI_NEEDS_WR_DELAY
to handle this and set this flag for TI 66AK2G SoC.
[1]http://www.ti.com/lit/ug/spruhy8f/spruhy8f.pdf
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
The variable was already marked 'const' before the previous
patch, but the qualifier was in an unusual place, and now the
extra 'const' causes a harmless warning:
drivers/mtd/spi-nor/cadence-quadspi.c:1286:34: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
This removes the other 'const' instead.
Fixes: f993c123b4 ("mtd: spi-nor: cqspi: make of_device_ids const")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
This patch changes the prototype of spi_nor_scan(): its 3rd parameter
is replaced by a 'struct spi_nor_hwcaps' pointer, which tells the spi-nor
framework about the actual hardware capabilities supported by the SPI
controller and its driver.
Besides, this patch also introduces a new 'struct spi_nor_flash_parameter'
telling the spi-nor framework about the hardware capabilities supported by
the SPI flash memory and the associated settings required to use those
hardware caps.
Then, to improve the readability of spi_nor_scan(), the discovery of the
memory settings and the memory initialization are now split into two
dedicated functions.
1 - spi_nor_init_params()
The spi_nor_init_params() function is responsible for initializing the
'struct spi_nor_flash_parameter'. Currently this structure is filled with
legacy values but further patches will allow to override some parameter
values dynamically, for instance by reading the JESD216 Serial Flash
Discoverable Parameter (SFDP) tables from the SPI memory.
The spi_nor_init_params() function only deals with the hardware
capabilities of the SPI flash memory: especially it doesn't care about
the hardware capabilities supported by the SPI controller.
2 - spi_nor_setup()
The second function is called once the 'struct spi_nor_flash_parameter'
has been initialized by spi_nor_init_params().
With both 'struct spi_nor_flash_parameter' and 'struct spi_nor_hwcaps',
the new argument of spi_nor_scan(), spi_nor_setup() computes the best
match between hardware caps supported by both the (Q)SPI memory and
controller hence selecting the relevant settings for (Fast) Read and Page
Program operations.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Checking for ret < 0 is redundant because a previous check on ret
being non-zero already handles the ret < 0 case. Remove the redundant
code. Found by CoverityScan, CID#1398863, CID#1398864
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
The x86-64 and some other architectures are missing readsl/writesl
functions, so this driver won't build on them. Use a more portable
ioread32_rep()/iowrite32_rep() instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alan Tull <atull@opensource.altera.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Graham Moore <grmoore@opensource.altera.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Yves Vandervennet <yvanderv@opensource.altera.com>
Suggested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
We return success or possibly uninitialized values on these error paths
instead of proper error codes.
Fixes: 1406234105 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
There are CQSPI_MAX_CHIPSELECT elements in the ->f_pdata array so the >
should be >=.
Fixes: 1406234105 ('mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Add support for the Cadence QSPI controller. This controller is
present in the Altera SoCFPGA SoCs and this driver has been tested
on the Cyclone V SoC.
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alan Tull <atull@opensource.altera.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Graham Moore <grmoore@opensource.altera.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Yves Vandervennet <yvanderv@opensource.altera.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>