If station info contains a beacon loss count, return
it to userspace.
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nl80211 station handling code is a bit messy
and doesn't do a lot of validation. It seems like
this could be an issue for drivers that don't use
mac80211 to validate everything.
As cfg80211 doesn't keep station state, move the
validation of allowing supported_rates to change
for TDLS only in station mode to mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was evidently missed in the TDLS patch (07ba55d7).
Cc: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All nl80211 commands that need only the wiphy
still allow identifying it by giving an interface
index, except, as Kenny pointed out, the testmode
dump support.
Fix this by looking up the wiphy via the ifidx in
this case as well.
Tested-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prepare cfg80211 for IBSS HT:
* extend cfg80211 ibss struct with channel_type
* Check if extension channel can be used
* Export can_beacon_sec_chan for use in mac80211 (will be called
from ibss.c later).
Signed-off-by: Alexander Simon <an.alexsimon@googlemail.com>
[siwu@hrz.tu-chemnitz.de: Updates]
* fix cfg80211_can_beacon_ext_chan comment
* remove implicit channel_type enum assumptions
* remove radar channel flags check
* add HT IBSS feature flag
* reword commit message
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As per 802.11mb 13.9.11.3
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains the configuration changes in nl80211/cfg80211.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MAC addresses have a fixed length. The current
policy allows passing < ETH_ALEN bytes, which
might result in reading beyond the buffer.
Cc: stable@vger.kernel.org
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows users to disable features such as HT, HT40,
and to modify the MCS, AMPDU, and AMSDU settings for
drivers that support it.
The MCS, AMPDU, and AMSDU features that may be disabled are
are reported in the phy-info netlink message as a mask.
Attemping to disable features that are not supported will
take no affect, but will not return errors. This is to aid
backwards compatibility in user-space apps that may not be
clever enough to deal with parsing the the capabilities mask.
This patch only enables the infrastructure. An additional
patch will enable the feature in mac80211.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_vlan() sets the output parameter even if it
returns an error, which is a bit odd. Instead,
convert it to use ERR_PTR.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently mac80211 implements these for all devices,
but given restrictions of some devices that isn't
really true, so prepare for being able to remove the
capability for some mac80211 devices.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
User space might want to test if driver supports testmode. Adding testmode
to the list of supported commands makes this easier.
I omitted testmode_dump() in purpose. I assume all drivers implementing
testmode_dump() will also implement testmode_cmd().
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wireless-regdb now has support for mapping a country to
one DFS region. CRDA sends this to us now so process it
so we can provide that hint to drivers. This will later be
used by code for processing DFS in a way that meets the
criteria for the DFS region the country belongs to.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass probe-response data from usermode via beacon parameters.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Notify user-space about probe-response offloading support in the driver.
A wiphy flag is used to indicate support and a bitmap of protocols
determines which protocols are supported.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John reported the following warning:
net/wireless/nl80211.c: In function ‘nl80211_tx_mgmt’:
net/wireless/nl80211.c:5286:8: warning: ‘hdr’ may be used uninitialized in this function
Evidently, his version of gcc isn't able to see that
when "msg" is initialized, "hdr" must also be. My
gcc, 4.6.1, can actually see that and doesn't warn.
Simply initialize the variable to NULL. That means
if the compiler was ever right we'll crash though so
isn't really optimal since it may hide warnings from
the compiler when somebody modifies this code in the
future.
Reported-by: John Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new wifi socket TX capability should be
supported by wifi drivers, let them advertise
whether they do or not.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For probe responses it can be useful to not wait for ACK to
avoid retransmissions if the station that sent the probe is
already on the next channel, so allow userspace to request
not caring about the ACK with a new nl80211 flag.
Since mac80211 needs to be updated for the new function
prototype anyway implement it right away -- it's just a
few lines of code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The frames are used by AP/STA WDS mode, and hostapd
needs to know when such a frame was received to set
up the VLAN appropriately to allow using it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the ability to register to received beacon frames
to allow implementing OLBC logic in userspace. The
registration is per wiphy since there's no point in
receiving the same frame multiple times.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the AP SME in hostapd is used it wants to
probe the clients when they have been idle for
some time. Add explicit API to support this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the ability to advertise that the device
contains the AP SME and what features it can
support. There are currently no features in
the bitmap -- probe response offload will be
advertised by a few patches Arik is working
on now (who took over from Guy Eilam) and a
device with AP SME will typically implement
and require response offload.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To implement AP mode without monitor interfaces we
need to be able to send a deauth to stations that
send frames without being associated. Enable this
by adding a new nl80211 event for such frames that
an application can subscribe to.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WPI-SMS4 uses 16-octet PN field, so we need to allow longer key
sequence values to be configured.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
genlmsg_end() cannot fail, it just returns the length
of the message. Thus, error handling for it is useless.
While removing it, I also noticed a useless variable
and removed this it as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In other modes the parameters should not be set.
Right now, mac80211 will set them, even if the
user asked for setting them on VLANs which the
driver doesn't know about, causing all kinds of
trouble.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the NL80211_ATTR_HT_CAPABILITY attribute is
used as a struct, it needs a minimum, not maximum
length. Enforce that properly. Not doing so could
potentially lead to reading after the buffer.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reuse the already existing struct nl80211_sta_flag_update to specify
both, a flag mask and the flag set itself. This means
nl80211_sta_flag_update is now used for setting station flags and also
for getting station flags.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When adding a TDLS peer STA, mark it with a new flag in both nl80211 and
mac80211. Before adding a peer, make sure the wiphy supports TDLS and
our operating mode is appropriate (managed).
In addition, make sure all peers are removed on disassociation.
A TDLS peer is first added just before link setup is initiated. In later
setup stages we have more info about peer supported rates, capabilities,
etc. This info is reported via nl80211_set_station().
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for sending high-level TDLS commands and TDLS frames via
NL80211_CMD_TDLS_OPER and NL80211_CMD_TDLS_MGMT, respectively. Add
appropriate cfg80211 callbacks for lower level drivers.
Add wiphy capability flags for TDLS support and advertise them via
nl80211.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, when hostapd sets the station as authorized
we also overwrite its uAPSD parameter. This obviously
leads to buggy behaviour (later, with my patches that
actually add uAPSD support). To fix this, only apply
those parameters if they were actually set in nl80211,
and to achieve that add a bitmap of things to apply.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct flag usage - use it as a bit index instead of a bit value.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tx params are currently configured per hw, although they
should be configured per interface.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new nl80211 attribute to specify whether to send the management
frames in CCK rate or not. As of now the wpa_supplicant is disabling
CCK rate at P2P init itself. So this patch helps to send P2P probe
request/probe response/action frames being sent at non CCK rate in 2GHz
without disabling 11b rates.
This attribute is used with NL80211_CMD_TRIGGER_SCAN and
NL80211_CMD_FRAME commands to disable CCK rate for management frame
transmission.
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using a hardcoded list of cipher suites in nl80211.c, use a
shared function in util.c to verify that the driver advertises support
for the specified cipher. This provides more accurate validation of the
values and allows vendor-specific cipher suites to be added in drivers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NL80211_ATTR_AKM_SUITES can be used to configure new AKMs, like FT or
the SHA-256 -based AKMs or FT from 802.11r/802.11w. In addition, vendor
specific AKMs could be used. The current validation code for the connect
command prevents cfg80211-based drivers from using these mechanisms even
if the driver would not actually use this AKM value (i.e., it uses
WPA/RSN IE from user space). mac80211-based drivers allow any AKM to be
used since this value is not used there.
Remove the unnecessary validation step in cfg80211 to allow drivers to
decide what AKMs are supported. In theory, we could handle this by
advertising supported AKMs, but that would not be very effective unless
we enforce all drivers (including mac80211) to advertise the set of
supported AKMs. This would require additional changes in many places
whenever a new AKM is introduced even though no actually functionality
changes may be required in most drivers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incorrect variable was used in validating the akm_suites array from
NL80211_ATTR_AKM_SUITES. In addition, there was no explicit
validation of the array length (we only have room for
NL80211_MAX_NR_AKM_SUITES).
This can result in a buffer write overflow for stack variables with
arbitrary data from user space. The nl80211 commands using the affected
functionality require GENL_ADMIN_PERM, so this is only exposed to admin
users.
Cc: stable@kernel.org
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the driver (or most likely firmware) decides which AP to use
for roaming based on internal scan result processing, user space
needs to be notified of PMKSA caching candidates to allow RSN
pre-authentication to be used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The IBSS BSSID is never validated, so an
invalid one might end up being used. Fix
this by rejecting invalid configuration.
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The format is intended to be like the subfields
in the QoS Info field, verify that is the case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce filtering for scheduled scans to reduce the number of
unnecessary results (which cause useless wake-ups).
Add a new nested attribute where sets of parameters to be matched can
be passed when starting a scheduled scan. Only scan results that
match any of the sets will be returned.
At this point, the set consists of a single parameter, an SSID. This
can be easily extended in the future to support more complex matches.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add WIPHY_FLAG_AP_UAPSD flag to indicate uapsd support on
AP mode.
Advertise it to userspace by including a new
NL80211_ATTR_SUPPORT_AP_UAPSD attribute.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the rssi of the current AP drops, both wpa_supplicant and the
firmware may do a background scan to find a better AP and try to
associate. Since firmware based roaming is faster, inform
wpa_supplicant to avoid roaming and let the firmware decide to
roam if necessary.
For fullmac drivers like ath6kl, it is just enough to provide the
ESSID and the firmware will decide on the BSSID. Since it is not
possible to do pre-auth during roaming for fullmac drivers, the
wpa_supplicant needs to completely disconnect with the old AP and
reconnect with the new AP. This consumes lot of time and it is
better to leave the roaming decision to the firmware.
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new NL80211_ATTR_STA_WME nested attribute that contains
wme params needed by the low-level driver (uapsd_queues and
max_sp).
Add these params to the station_parameters struct as well.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to set NL80211_MESHCONF_GATE_ANNOUNCEMENTS attribute,
which will advertise this mesh node as being a mesh gate.
NL80211_HWMP_ROOTMODE must be set or this will do nothing.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to set Root Announcement Interval for our mesh
interface. Also, RANN interval is now in proper units of TUs.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Paul Stewart