A secure element can be activated in different order.
The host_list is updated keeping a fixed order:
<terminal_host_id><uicc_id><ese_id>.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
After internal discussion, it appears this timing should be
increased to 20 ms for interoperability reason.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to align with st21nfca, dts configuration properties
ese_present and uicc_present are made available in st-nci driver.
So far, in early development firmware, because
nci_nfcee_mode_set(DISABLE) was not supported we had to try to
enable it during the secure element discovery phase.
After several trials on commercial and qualified firmware it appears
that nci_nfcee_mode_set(ENABLE) and nci_nfcee_mode_set(DISABLE) are
properly supported.
Such feature also help us to eventually save some time (~5ms) when
only one secure element is connected.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Potentially an unexpected HCI event may occur because of a
firmware bug. It could be transparent for the user but we need to
at least log it.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for proprietary commands useful mainly for
factory testings. Here is a list:
- FACTORY_MODE: Allow to set the driver into a mode where
no secure element are activated. It does not consider any
NFC_ATTR_VENDOR_DATA.
- HCI_CLEAR_ALL_PIPES: Allow to execute a HCI clear all pipes
command. It does not consider any NFC_ATTR_VENDOR_DATA.
- HCI_DM_PUT_DATA: Allow to configure specific CLF registry
like for example RF trimmings or low level drivers
configurations (I2C, SPI, SWP).
- HCI_DM_UPDATE_AID: Allow to configure an AID routing into the
CLF routing table following RF technology, CLF mode or protocol.
- HCI_DM_GET_INFO: Allow to retrieve CLF information.
- HCI_DM_GET_DATA: Allow to retrieve CLF configurable data such as
low level drivers configurations or RF trimmings.
- HCI_DM_DIRECT_LOAD: Allow to load a firmware into the CLF.
A complete packet can be more than 8KB.
- HCI_DM_RESET: Allow to run a CLF reset in order to "commit" CLF
configuration changes without CLF power off.
- HCI_GET_PARAM: Allow to retrieve an HCI CLF parameter (for example
the white list).
- HCI_DM_FIELD_GENERATOR: Allow to generate different kind of RF
technology. When using this command to anti-collision is done.
- HCI_LOOPBACK: Allow to echo a command and test the Dh to CLF
connectivity.
- HCI_DM_VDC_MEASUREMENT_VALUE: Allow to measure the field applied
on the CLF antenna. A value between 0 and 0x0f is returned. 0 is
maximum.
- HCI_DM_FWUPD_START: Allow to put CLF into firmware update mode.
It is a specific CLF command as there is no GPIO for this.
- HCI_DM_FWUPD_END: Allow to complete firmware update.
- HCI_DM_VDC_VALUE_COMPARISON: Allow to compare the field applied
on the CLF antenna to a reference value.
- MANUFACTURER_SPECIFIC: Allow to retrieve manufacturer specific data
received during a NCI_CORE_INIT_CMD.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It is useless to start from index 0 when looking for a gate
because only dynamic pipes are retrieved with
ST_NCI_DM_GETINFO(ST_NCI_DM_GETINFO_PIPE_LIST).
The first dynamic pipe is present at index 3.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NCI_HCI_IDENTITY_MGMT_GATE might be useful to get information
about hardware or firmware version.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When initializing ndev->hci_dev->init_data, only gates field
was set. gate_count needs to be initialized as well.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We need to keep initial st_nci_gates values in order for
nci_hci_dev_connect_gates to create and open pipe when necessary.
For example after a firmware update CLF pipes are cleared. Changing
pipe values in st_nci_gates was causing nci_hci_dev_connect_gates
not using accurate pipes value.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NCI_HCI_LINK_MGMT_PIPE was never opened in st_nci_hci_load_session.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard